Samsung SC21F50VA Manuale utente

English

Vacuum Cleaner

user manual

Thank you for purchasing a Samsung product.

To receive a more complete service,

please register your product at

www.samsung.com/register

SC21F50 series

✻ Before operating this unit, please read the instructions carefully.

✻ For indoor use only.

02_ safety information

safety information

SAFETY INFORMATION

WARNING

• Before operating the appliance, please read this manual thoroughly and retain it for your

reference.

WARNING

• Because these following operating instructions cover various models, the characteristics of

your vacuum cleaner may differ slightly from those described in this manual.

CAUTION/WARNING SYMBOLS USED

WARNING

Indicates that a danger of death or serious injury exists.

CAUTION

Indicates that a risk of personal injury or material damage exists.

OTHER SYMBOLS USED

Represents something you must NOT do.

Represents something you must follow.

Indicates that you must disconnect the power plug from the socket.

This vacuum cleaner is designed for household use only.

Do not use this vacuum cleaner to clean building waste and debris.

Regularly keep the ﬁ lters in clean conditions to prevent of collecting ﬁ ne dust in them.

Do not use this vacuum cleaner with any of the ﬁ lters removed.

Failure to meet these requirements could cause damage to the internal parts and void

your warranty.

WARNING

safety information _03

IMPORTANT SAFEGUARDS

GENERAL

• Read all instructions carefully. Before switching on, make sure

that the voltage of your electricity supply is the same as that

indicated on the rating plate on the bottom of the cleaner.

• WARNING : Do not use the vacuum cleaner when rug or ﬂ oor is

wet. Do not use to suck up water.

• Close supervision is necessary when any appliance is used by

or near children. Do not allow the vacuum cleaner to be used

as a toy. Do not allow the vacuum cleaner to run unattended at

any time. Use the vacuum cleaner only for its intended use as

described in these instructions.

• Do not use the vacuum cleaner without a dust bin.

Empty the dust bin before it is full in order to maintain the best

efﬁ ciency.

• Do not use the vacuum cleaner to pick up matches, live ashes or

cigarette butts. Keep the vacuum cleaner away from stoves and

other heat sources. Heat can deform and discolour the plastic

parts of the unit.

• Avoid picking up hard, sharp objects with the vacuum cleaner as

they may damage the cleaner parts.

Do not stand on the hose assembly. Do not put weight on the

hose.

Do not block the suction or the exhaust port.

• Switch the vacuum cleaner off on the body of the machine

before unplugging from the electrical outlet. Disconnect the plug

from the electrical outlet before emptying the dust bin. To avoid

damage, please remove the plug by grasping the plug itself, not

by pulling on the cord.

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

04_ safety information

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance. Cleaning and user

maintenance shall not be made by children without supervision.

• Children should be supervised to ensure that they do not play

with the appliance.

• The plug must be removed from the socket outlet before

cleaning or maintaining the appliance.

• The use of an extension cord is not recommended.

• If your vacuum cleaner is not operating correctly, switch off the

power supply and consult an authorized service agent.

• If the supply cord is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualiﬁ ed person in

order to avoid a hazard.

• Don’t carry the vacuum cleaner by holding the hose.

Use the handle on the vacuum cleaner set.

• Unplug the cleaner when not in use.

Turn off the power switch before unplugging.

UV BRUSH

• Since the UV rays from the UV Brush damage skin and eyes,

never allow the rays to make contact with skin or eyes and do

not let children or the elderly use the UV Brush. It may damage

your eyesight.

• If the transparent window is broken and the UV rays are exposed

directly, turn the power off and contact the service center.

• Do not use the UV Brush for purposes other than the sterilization

of mattresses, bedclothes, beds, cushions and so on made from

material. The company will not be held liable for any loss due to

accidents from using the UV Brush for purposes other than its

original purpose as listed above.

safety information

safety information _05

• Do not sit on the UV Brush or drop it, and avoid imparting

impacts on the product. Failing to do so may result in injury or

product damage.

• Do not touch the power terminals on the back of the UV Brush

with a metal pin or rod. This may result in electric shock or ﬁ re.

• When the UV lamp is out of order, never disassemble or modify

the product yourself.

Please contact the manufacturer or service center for a

replacement.

• Since an internal discharge occurs within the UV Brush, never

use the product near an inﬂ ammable spray or substance.

• Take care not to touch the UV lamp window after using the

UV Brush for an extended period of time as the surface of the

window may be hot.

• The UV Brush may start slowly at a low temperature due to the

inherent characteristics of UV lamps. Please keep the UV Brush

indoors.

06_ contents

contents

ASSEMBLING THE CLEANER

07

OPERATING THE CLEANER

08

08 Power cord

08 Power control

10 Using the UV brush (SC21F50U Series)

MAINTAIN TOOLS AND FILTER

11

11 Using accessory

13 Maintain ﬂ oor tools

16 Emptying the dust bin

17 Cleaning the dust ﬁ lter

18 Cleaning the dust ﬁ lter

19 Cleaning the outlet ﬁ lter

TROUBLESHOOTING

20

assembling the cleaner _07

01 ASSEMBLING THE CLEANER

• Please do not press the button of dust bin handle

when carrying machine.

• For storage, park the ﬂ oor nozzle.

assembling the cleaner

OPTION

08_ operating the cleaner

POWER CORD

CAUTION

• When removing the plug from the electrical outlet, grasp the plug, not the

cord.

POWER CONTROL

Radio frequency remote-control (SC21F50H, SC21F50U Series)

HOSE (SC21F50H Series)

1. ON/OFF [ ] Button

- Press the [

] button to operate the vacuum cleaner. Press

again to stop the vacuum cleaner.

2. Suction [+], [-] Button

- Press the [+] button to operate the vacuum to high suction

power. Press the [-] button to operate the vacuum to low

suction power.

If no button is pressed for 30 minutes while cleaning, the safety device is activated and the

power is cut off.

In this case, press the [Power] button on the main unit or unplug and then plug the power cord

in again.

operating the cleaner

Handle Control

The cleaner is controlled by radio

frequency signals.

sender

operating the cleaner _09

02 OPERATING THE CLEANER

HOSE (SC21F50U Series)

1. ON/OFF [ ] Button

- Press the [ ] button to operate the vacuum cleaner. Press

again to stop the vacuum cleaner.

2. [SUCTION (-/+)] Button

- Press the [SUCTION (-/+)] button to increase or decrease the

suction power. Each time you press the button, you gradually

increase the suction power. After the suction power reaches its

maximum, the next time you press the button, you return the

suction power to its minimum.

3. [BRUSH ON/OFF] Button

- Press the [BRUSH ON/OFF] button to operate the UV Brush. Press again to stop the UV Brush.

If no button is pressed for 30 minutes while cleaning, the safety device is activated and the

power is cut off.

In this case, press the [Power] button on the main unit or unplug and then plug the power cord

in again.

Change the battery

• When the vacuum cleaner does not work, replace the batteries.

If the problem persists, please contact our authorized dealer.

• Use 2 batteries of size AAA.

1. Never disassemble or recharge the batteries.

2. Never heat up the batteries or throw them into ﬁ re.

3. Do not reverse (+), (-) poles.

4. Dispose of the batteries property.

BODY

Press the power ON/OFF button repeatedly to start and to stop

the vacuum cleaner. (OFF → ON → OFF)

If the remote handle control is not working, the cleaner

can be operated using the ON/OFF button on the body

of the machine.

The ON/OFF button operates the vacuum cleanner or stops it.

The ﬁ lter light is illuminated when the dust pack requires checking or emptying.

CAUTION

Handle Control

The cleaner is controlled by radio

frequency signals.

sender

1

2

BATTERY TYPE : AAA Size

10_ operating the cleaner

Body-control type (SC21F50V Series)

- HOSE

To reduce suction for leaning draperies, small rugs, and other

light fabrics, pull the tap air until the hole is open

- BODY

To control power level, just slide the power control up and

down.

MIN = For delicate fabrics, e.g.net curtains.

MAX = For hard ﬂ oors and heavily soiled carpets.

USING THE UV BRUSH (SC21F50U SERIES)

1. Insert the brush into the hose handle.

• Insert the UV brush securely into the hose handle until you hear a “clicking”

sound.

2. Press the [BRUSH ON/OFF] button to start cleaning.

• Press the [BRUSH ON/OFF] button and choose the appropriate

suction strength for the cleaner.

• It is advisable to select the (Max) suction strength setting.

• UV sterilization cannot be activated by itself.

3. When you have ﬁ nished UV cleaning, press the [

] button.

• Press the [ ] button to stop the cleaner.

- For safety reasons, UV brushing only runs for 30 minutes and then stops

operating. To resume the operation, press the [SUCTION (-/+)] button again.

The UV brush, which is inserted into the hose handle (not directly connected to the telescopic

pipe), is dedicated for bedclothes.

CAUTION

MIN

MAX

MIN

MAX

maintain tools and ﬁ lter _11

03 MAINTAIN TOOLS AND FILTER

USING ACCESSORY

Pipe

• Adjust the length of the telescopic pipe by sliding the length control

button located in the center of the telescopic pipe back and forth.

• To check for blockages, separate the telescopic pipe and adjust to

shorten. This allows for easier removal of waste clogging the tube.

Accessory (SC21F50H, SC21F50V Series)

• To use the upholstery tool, push the accessory

on to the end of the hose handle.

• Pull out the button, to use the dusting brush.

• To use the crevice tool, push the accessory on

to the end of the hose handle in the opposite

direction.

maintain tools and ﬁ lter

12_ maintain tools and ﬁ lter

Accessories (SC21F50U Series)

• Push the accessory onto the end of the hose

handle.

• Pull out the dusting brush to use the crevice tool.

• Push the accessory onto the end of the pipe.

• Pull out the dusting brush to use the crevice

tool.

maintain tools and ﬁ lter

maintain tools and ﬁ lter _13

03 MAINTAIN TOOLS AND FILTER

MAINTAIN FLOOR TOOLS

2-Step Brush

• Adjust the inlet lever according to the ﬂ oor surface.

• Remove waste matter completely if the inlet is blocked.

Power Pet Plus Brush (Option)

Frequent vacuuming of hair or pet fur may cause a falling-off of the rotation due to matters tangled around

the drum. In this case, clean the drum with care.

1. Push the Open button of the transparent screen cover to separate the cover.

2. Remove the brushbar from the transparent screen.

3. Remove waste matter such as dust and hair tangled around the brushbar using scissors.

4. Remove dust inside the brush housing using a dry duster or crevice tool.

5. Insert brushbar into rotating belt and assemble.

6. Click the transparent screen cover back into place to reassemble.

Parquet Master Brush (Option)

• Vacuum dust in wide area at once.

• Remove waste matter completely if the inlet is

blocked.

Carpet Cleaning Floor Cleaning

1 2

4 5

3

6

For improved pickup

of pet hair and ﬁ bre on

carpets.

14_ maintain tools and ﬁ lter

Mini turbo brush (Option)

- To replace brushroll

1. If a clog is present or debris is visible, unscrew the two screws on

the back of the Mini turbo brush to remove the faceplate and clear

any obstructions.

2. Inspect condition of brushroll.

Replace brushroll if brushes are worn down.

To remove brushroll, pull up and out of end slots in nozzle housing.

Insert ends of brushroll into same slots to replace.

Inspect belt to ensure that it is in good condition.

If belt is broken or cracked, replace belt according to To Replace

Belt instructions.

3. Using at MAX.

Press the MAX button to operate the vacuum at maximum intake.

- To replace belt

1. Remove bottom plate.

See ﬁ gure in To Replace Brushroll instructions.

2. Loop one end of new belt around shaft of pulley.

3. Loop other end of belt around designated area for it on brushroll.

Insert brushroll into slots in nozzle housing.

See ﬁ gure in To Replace Brushroll instructions.

4. Fit Mini turbo brush back together as described in To Replace

Brushroll instructions.

maintain tools and ﬁ lter

maintain tools and ﬁ lter _15

03 MAINTAIN TOOLS AND FILTER

To remove dust from the dust bin of the UV brush (SC21F50U Series)

When you notice that the dust bin is ﬁ lled, use the [Dust Removal] button to empty the dust bin.

1. To remove dust from the dust bin, move the [Dust Removal] button

to the “Open” position.

- While the cleaner is operating (suction), use the [Dust Removal]

button for this purpose.

2. When done, move the [Dust Removal] button to the “Close”

position.

- When the [Dust Removal] button is in the “Open” position, the

suction power of the cleaner is reduced.

Cleaning the UV brush (Cleaning the drum) (SC21F50U Series)

Human and pet hair often becomes tangled in the drum, causing a reduction in the rotary power of the

the drum. To prevent this, clean the drum on a regular basis.

1. Push the [Open Transparent Cover] button inward to remove the

cover.

2. Use the crevice tool to remove impurities such as dust and hair

from around the drum.

3. When done, push the [Open Transparent Cover] button outward to

close the cover.

16_ maintain tools and ﬁ lter

EMPTYING THE DUST BIN

maintain tools and ﬁ lter

1

2

Once dust reaches the dust full

mark, empty the dust bin.

Take the dust bin out by pushing

the button.

Separate the dust bin cover.

1

2

Click

Throw the dust away in the bin. Close the dust bin cover.

Before use, push the dust

bin into the main body of the

vacuum cleaner until you hear

the “click” sound.

12 3

45 6

You may rinse the dust bin with cold

water.

• Empty into a plastic bag.

(recommended for asthma/allergy sufferers)

maintain tools and ﬁ lter _17

03 MAINTAIN TOOLS AND FILTER

CLEANING THE DUST FILTER

When to clean the dust ﬁ lter

• The lamp will turn red when suction is

reduced. If the light comes on, please

clean the dust ﬁ lter.

• Turn the vacuum power to ‘MAX’.

• If the ﬁ lter check indicator turns red with the inlet ﬂ oating 10cm above

ﬂ at ﬂ oor, clean the dust pack.

When suction is noticeably reduced continuously or vacuum cleaner abnormally overheats,

please clean the dust pack.

Handle Control

Body Control

18_ maintain tools and ﬁ lter

CLEANING THE DUST FILTER

Make sure the ﬁ lter is completely dry before putting it back into the

vacuum cleaner. Allow 12 hours for it to dry.

maintain tools and ﬁ lter

12 3

78

Take the dust bin out. Pull the dust bin cover to open.

Remove the ﬁ lter from the dust

bin.

Shake the ﬁ lter over a garabage

can to remove loose dust, then

wash the ﬁ lter with water.

Let the ﬁ lter dry in the shade for

more than 12 hours.

Put the ﬁ lter into the dust bin.

Close the dust bin cover.

Before use, push the dust

bin into the main body of the

vacuum cleaner until you hear

the “click” sound.

To close the dust bin cover,

ﬁ lter should be assembled.

45

6

maintain tools and ﬁ lter _19

03 MAINTAIN TOOLS AND FILTER

CLEANING THE OUTLET FILTER

• When suction is noticeably reduced continuously or vacuum cleaner abnormally overheats,

please clean the outlet ﬁ lter. Note. Do not wash HEPA ﬁ lter.

If cleaning does not resolve the problem Please replace blocked out ﬁ lter.

• Replacement ﬁ lters are available at your local Samsung distributor.

Remove the ﬁ xed frame part at

the back of the main body.

Pull out the HEPA ﬁ lter using the

tab.

Pull out the micro ﬁ lter

Clean the ﬁ lter. Put the HEPA ﬁ lter and frame part into the main body.

12 3

45

20_ troubleshooting

troubleshooting

PROBLEM SOLUTION

Motor does not start.

• Check cable, pulg and socket.

• Leave to cool.

Suction force is gradually

decreasing.

• Check for blockage and remove.

Cord does not rewind

fully.

• Pull the cord out 2-3m and push down the cord rewind button.

Vacuum cleaner dows not

pick up dirt.

• Check hose and replace if required.

Low or decreasing

suction.

• Please check ﬁ lter and, if required, clean as illustrated in the

instructions. if ﬁ lters are out of condition change them to new ones.

Body overheating. • Please check ﬁ lters, if required clean as illustrated in the instruction.

Static electicity

discharge.

• Please decrease power suction.

• This can also occur when air in the room is very dry.

Please ventilate the room to air humidity become a normal.

This Vacuum cleaner is approved the following.

Electromagnetic Compatibility Directive : 2004/108/EEC

Low Voltage Directive : 2006/95/EC

La pagina si sta caricando...

Samsung SC21F50VA Manuale utente

Questo manuale è adatto anche per

Samsung SC21F50VA Manuale utente

in altre lingue

Documenti correlati

Altri documenti