EPOX EP-MVP3C2 Manuale utente

TRADEMARK

All products and company names are trademarks or registered

trademarks of their respective holders.

These specifications are subject to change without notice.

Manual Revision 1.1

October 1, 1999

EP-MVP3CEP-MVP3C

EP-MVP3C

EP-MVP3C2EP-MVP3C2

EP-MVP3C2

ISA/PCI AGP Mainboard with OnboardISA/PCI AGP Mainboard with Onboard

ISA/PCI AGP Mainboard with Onboard

PCI IDE and Super Multi-I/OPCI IDE and Super Multi-I/O

PCI IDE and Super Multi-I/O

EP-MVP3C/2

User Notice

No part of this product, including the product and software may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language in

any form without the express written permission of EPoX Computer Company

(hereinafter referred to as EPoX) except for documentation kept by the purchaser for

backup purposes.

We provide this manual “as is” without warranty of any kind, either expressed or

implied, including but not limited to the implied warranties or conditions of merchant-

ability or fitness for a particular purpose. In no event shall EPoX be liable for any loss

of profits, loss of business, loss of use or data, interruption of business or for indirect,

special incidental, or consequential damages of any kind, even if EPoX has been

advised of the possibility of such damages arising from any defect or error in the

manual or product. EPoX may revise this manual from time to time without notice.

For updated BIOS, drivers, or product release information you may visit our websites

at http://www.epox.com or http://www.epox.com.tw.

Products mentioned in this manual are mentioned for identification purposes only.

Product names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies. The product name and revision number

are both printed on the mainboard itself.

Handling Procedures

Static electricity can severely damage your equipment. Handle the EP-MVP3C/2 and

any other device in your system with extreme care and avoid unnecessary contact with

system components on the mainboard. Always work on an antistatic surface to avoid

possible damage to the mainboard from static discharge. Always have the power

supply unplugged and powered off when inserting and removing devices within the

computer chassis. EPoX assumes no responsibility for any damage to the EP-MVP3C/

2 mainboard that results from failure to follow instruction or failure to observe safety

precautions.

CAUTION

The EP-MVP3C/2 mainboard is subject to

damage by static electricity. Always

observe the handling procedures.

EP-MVP3C/2

Technical Support Services

If you need additional information, help during installation or normal use of this

product, please contact your retailer. Your retailer will have the most current informa-

tion about your configuration. If your retailer cannot help, you may visit our online

technical support website and/or contact our support technicians at the locations listed

below.

Record your serial number before installing your EP-MVP3C/2 mainboard. (The serial

number is located near the ISA slots at the edge of the board.)

EP-MVP3C/2 serial number: _________________________________

Contacting Technical Support

EPoX technical support is working hard to answer all of your questions online. From

our website you can find answers to many common questions, drivers, BIOS updates,

tech notes, and important technical bulletins. If you are still unable to locate the

solution you are seeking, you always have the option to contact our support technicians

directly.

North American website (English language)

http://www.epox.com

[email protected]

European website (Multi-language)

http://www.epox.nl

[email protected]

Taiwan website (Chinese language)

http://www.epox.com.tw

[email protected]

Thank you for using EPoX mainboards!

EP-MVP3C/2

Table of Contents

Section 1 Introduction

Components Checklist ................................... 1-1

Overview

Power-On/Off (Remote) ................................. 1-2

System Block Diagram ................................... 1-3

Section 2 Features

EP-MVP3C/2 Features.................................. 2-1

Section 3 Installation

EP-MVP3C/2 Detailed Layout ...................... 3-2

Easy Installation Procedure

Configure Jumpers......................................... 3-3

System Memory Configuration ........................ 3-5

Device Connectors ......................................... 3-8

External Modem Ring-in Power ON and

Keyboard Power ON Function (KBPO) ........ 3-10

Section 4 Award BIOS Setup

BIOS Instructions ........................................... 4-1

Standard CMOS Setup .................................. 4-2

BIOS Features Setup ..................................... 4-3

Chipset Features Setup ................................... 4-7

Power Management Setup .............................. 4-9

PNP/PCI Configuration .................................. 4-12

Load Setup Defaults ....................................... 4-14

Integrated Peripherals ..................................... 4-14

Change Supervisor or User Password ............. 4-18

IDE HDD Auto Detection............................... 4-19

HDD Low Level Format................................. 4-21

Page

EP-MVP3C/2

Save & Exit Setup ......................................... 4-21

Exit Without Saving......................................... 4-21

Appendix

Appendix A

Memory Map................................................. A-1

I/O Map......................................................... A-1

Timer & DMA Channels Map......................... A-2

Interrupt Map ................................................. A-2

RTC & CMOS RAM Map ............................ A-3

Appendix B

POST Codes ................................................. A-5

Unexpected Errors ......................................... A-8

Appendix C

Load Setup Defaults ...................................... A-9

Appendix D

GHOST 5.1 Quick User’s Guide................... A-11

EP-MVP3C/2

Page Left Blank

IntroductionEP-MVP3C/2

Page 1-1

Section 1

INTRODUCTION

Components Checklist

üü

ü A. (1) One mainboard

üü

ü B. (1) One user’s manual

üü

ü C. (1) Floppy ribbon cable

üü

ü D. (1) IDE ribbon cables

ATA-66 IDE ribbon cable (EP-MVP3C2 only)

E. (1) PS/2 Mouse connector

üü

ü F. (1) COM Port/LPT Port Connector

üü

ü G. (1) Driver and Utility

USERS

MANUAL

EP-MVP3C/2

B

A

C

D

G

or

E

F

Introduction EP-MVP3C/2

Page 1-2

ATX

POWER SUPPLY

EP-MVP3C/2 Board

Power-On/Off (Remote)

The EP-MVP3C/2 has a single 20-pin connector for ATX power supplies. For ATX

power supplies that support the Remote On/Off feature, this should be connected to

the systems front panel for system Power On/Off button. The systems power On/

Off button should be a momentary button that is normally open.

The EP-MVP3C/2 has been designed with “Soft Off" functions. You can turn Off the

system from one of two sources: The first is the front panel Power On/Off button,

and the other is the "Soft Off" function (coming from the EP-MVP3C/2’s onboard

circuit controller) that can be controlled by the operating system. Windows 95/98 will

control this when the user clicks that they are ready to Shutdown the system.

Case (chassis) Power

ON/OFF button

Figure 4: Simple ATX Power

ON/OFF Controller

J3

IntroductionEP-MVP3C/2

Page 1-3

Figure 5: System Block Diagram

System Block Diagram

PAC

PCI Bridge

and memory

controller

VT82C598

VT82C596

I/O Bridge

Socket 7

Processor

100/66 MHz

66 MHz

Winbond

83877TF

USB 0

USB 1

Introduction EP-MVP3C/2

Page 1-4

Page Left Blank

FeaturesEP-MVP3C/2

Page 2-1

Section 2

FEATURES

EP-MVP3C/2 Features:

• Intel Pentium

®

Processor with MMX technology, AMD K6/K6-2/K6 III, Cyrix

6x86MX/MII, IDT C6 & Rise MP6 operating at 133 ~ 500 MHz with 321 ZIF

socket 7 provides scalability to accept faster Processors in the future. The board

is configured by an Easy-Setting-Dual-Jumper (E.S.D.J.) to match your CPU

clock speed.

• Designed with VIA MVP3 AGPset.

• Supports up to 384 MB of DRAM (minimum of 16 MB) on board, You can

use 168-pin DIMM x 3. It will automatically detect Extended Data Output

(EDO) DRAM at 66MHz only or Synchronous DRAM memory (SDRAM) at

66MHz or 100MHz (please see Section 3-2).

• Supports (2) 16 bit ISA slots, (4) 32 bit PCI slots, (1) AGP slot and provides

(2) independent high performance PCI IDE interfaces capable of supporting

PIO Mode 3/4 and Ultra DMA 33/66(for EP-MVP3C2 only) devices.

The EP-MVP3C/2 supports (4) PCI Bus Master slots and a jumperless PCI

INT# control scheme which reduces configuration confusion when plugging in

PCI card(s).

ATA-66 HDD Tested & Recommended: WD AC-313000

for EP-MVP3C2 IBM DJNA-370910

Fujitsu Mpd3043AT

Quantum CR8400AT

• Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary IDE

interfaces.

• Designed with Winbond W83877TF Multi I/O: (1) floppy port, (1) parallel port

(EPP, ECP), and (2) serial ports (16550 Fast UART).

Note: Japanese “Floppy 3 mode” is also supported.

• Built-in ATX 20-pin and AT 12-Pin power supply connector.

• Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released. (http://www.epox.com

please visit our Technical Support section for the latest updates).

Features EP-MVP3C/2

Page 2-2

• EP-MVP3C/2 utilizes a Lithium battery which provides environmental protection

and longer battery life.

• Software power-down when using Windows

®

95/98.

• Supports ring-in feature (remote power-on through external modem,

allows system to be turned on remotely).

• Resume by Alarm - Allows your system to turn on at a preselected time.

• Supports CPU Hardware sleep and SMM (System Management Mode).

• Supports Keyboard power ON function (KBPO).

• Supports USDM software to offer motherboard various status.

• Supports the CPU, PWR and Chassis fan Auto stop in sleep mode.

• Built-in WOL (Wake On Lan) Connector.

• Built-in SB-LINK Header for Creative Blaster

®

compatible AWE64D PCI Bus

Sound Card.

InstallationEP-MVP3C/2

Page 3-1

Section 3

INSTALLATION

Installation EP-MVP3C/2

Page 3-2

Figure 1

EP-MVP3C/2 Detailed Layout

AGP SLOT

PCI Slot #2

VIA

VT82C598

J7

WOL

J1

1

IDE1IDE2

FDD1

DIMM 1

DIMM 2

Bank 1

Bank 0

DIMM 3

Bank 2

PCI Slot #1

J2

RESET

SPK

KEYLOCK

POWER_ON

1

J3

IR CONN.

+

5

1

5

JP5

1

JP4

POWER_ON

JP3

2 1

28 27

PCI Slot #3

PCI Slot #4

ISA Slot #1

BIOS

1

JP1

J4

CPU FAN

J6

CHASSIS FAN

J8

SB_Link

1

2

5

6

USB CONN.

19

816

ISA Slot #2

PW1

PW2

InstallationEP-MVP3C/2

Page 3-3

Easy Installation Procedure

The following must be completed before powering on your new system:

3-1. Configure Jumpers

3-2. System Memory Configuration

3-3. Device Connectors

3-4. External Modem Ring-in Power ON and Keyboard Power ON

Functions (KBPO)

Section 3-1

Configure Jumpers

We design this motherboard with the fewest jumpers to make your install fast and

easy.

The following will describe all of the jumpers that you are required to set before

moving on to step 3-2.

Note: The jumpers as depicted as shown (Figure 1) in their correct physical

orientation.

J7 WOL (Wake On Lan) Connector

Reserved for NIC (Network Interface Card) to

Wake the System.

1-2 - Run Mode (Default)

2-3 - Clear CMOS (momentarily)

JP1 CMOS Clear

1

3

J8 SB-LINK Header

Reserved for Creative SB-LINK (Sound Blaster

LINK ) with the Sound Blaster AWE64D PCI

Sound Card to Compatible DOS games and

Multimedia applications.

TM

JP4

Disabled(Default)

Enabled

Keyboard Power-ON function (refer to the section 3-5)

1-2 -

2-3 -

3

1

JP5 DIMM Clock Selection

1-2 - DIMM = AGP

2-3 - DIMM = CPU

3

1

Installation EP-MVP3C/2

Page 3-4

1

2

34

ON

5

1WS

UPC

erocV

1234 5

NONONOV8.1

NONONONOV0.2

NOV1.2

NOV2.2

NONOV3.2

NOV4.2

NOV8.2

NONOV9.2

NONOV2.3

SW1: CPU Vcore Voltage Selection

JP3: CPU Speed Selection

JP3

27

28

21

100MHz

112MHz

95MHz

83MHz

75MHz

66MHz

5.5X

5X

4.5X

4X

3.5X

3X

2.5X

2X

ESDJ

CPU Type

CPU

Bus

Clock

CPU

Multiplier

Pentium/MMX

AMD K6/K6-2/K6III

IDT-C6

Cyrix /IBM

6x86MX/MII

IDT Winchip 2 Rise MP6

166MHz PR200 66MHz

2.5X

PR233 75MHz

PR266 233MHz 83MHz

PR300 *PR333 95MHz

250MHz PR366 300MHz *PR366 100MHz

200MHz PR266 200MHz 66MHz

3X

PR300 225MHz 75MHz

250MHz PR333 266Mhz 83MHz

PR400 *PR380 95MHz

300MHz *PR433 *PR400 100MHz

233MHz PR300 233MHz 66MHz

3.5X

PR333 75MHz

*PR400 83MHz

333MHz *PR466 *PR433 95MHz

350MHz *PR500 *PR466 100MHz

266MHz *PR333 266MHz 66MHz

4X

*PR400 75MHz

333MHz *PR466 83MHz

380MHz *PR533 95MHz

400MHz *PR550 100MHz

300MHz 66MHz

4.5X

450MHz 100MHz

333MHz 66MHz

5X475MHz 95MHz

*500MHz 266MHz 100MHz

366MHz 66MHz

5.5X

*550MHz 300MHz 100MHz

* Reserved

InstallationEP-MVP3C/2

Page 3-5

Section 3-2

System Memory Configuration

Memory Layout

The EP-MVP3C/2 supports (3) 168-pin DIMMs (Dual In-line Memory Module). The

DIMMs can be either EDO (Extended Data Out) or SDRAM (Synchronized

DRAM). The DIMMs may be installed using just one chip.

• We recommend using SDRAM DIMM can not mixing

with EDO DIMM modules.

• DIMM SDRAM may be 83MHz (-12ns), 100MHz (-10ns) or

125MHz (-8ns) bus speed.

• No Registered DIMM support.

Figure 2 and Table 1 show several possible memory configurations using

* SDRAM only supports 8, 16, 32, 64, 128MB DIMM modules.

Table 1

DIMM 1

DIMM 2

Bank 0/1

Bank 2/3

-Synchronous

-EDO

DIMM 3

Bank 4/5

yromeMlatoT

1MMID

)1/0knaB(

2MMID

)3/2knaB(

3MMID

)5/4knaB(

BM821=

mumixaM

*MARDS/ODE

,BM23,BM61,BM8

1XBM821,BM46

enoNenoN

BM652=

mumixaM

*MARDS/ODE

,BM23,BM61,BM8

1XBM821,BM46

*MARDS/ODE

,BM23,BM61,BM8

1XBM821,BM46

enoN

BM483=

mumixaM

*MARDS/ODE

,BM23,BM61,BM8

1XBM821,BM46

*MARDS/ODE

,BM23,BM61,BM8

1XBM821,BM46

*MARDS/ODE

,BM23,BM61,BM8

1XBM821,BM46

Figure 2

Installation EP-MVP3C/2

Page 3-6

DIMM Module Installation

Figure 3 displays the notch marks and what they should look like on your DIMM

memory module.

DIMMs have 168-pins and two notches that will match with the onboard DIMM

socket. DIMM modules are installed by placing the chip firmly into the socket at a

90 degree angle and pressing straight down (figure 6) until it fits tightly into the

DIMM socket (figure 7).

Figure 3

CENTER KEY ZONE

(3.3 V DRAM)

LEFT KEY ZONE

(UNBUFFERED)

InstallationEP-MVP3C/2

Page 3-7

Figure 4

DIMM Module clip before installation

Figure 5

DIMM Module clip after installation

To remove the DIMM module simply press down both of the white clips on either

side and the module will be released from the socket.

Installation EP-MVP3C/2

Page 3-8

Section 3-3

Device Connectors

Please install the motherboard into the chassis.

Now that your motherboard is installed you are ready to connect all your connections

(figure 1).

J1: PS/2 mouse connector

J4: CPU Fan Power

• A plug-in for the CPU Fan Power

J6: Chassis Fan Power

• A plug-in for the chassis Fan Power

J7: WOL (Wake On Lan) Connector

J8: SB-LINK Connector

• 5-PIN Header for Creative Blaster

®

AWE64D PCI Sound Card.

PW1: AT Power Connector

• 12-pin power connector

PW2: ATX Power Connector

• 20-pin power connector

J2,J3:Chassis Panel Connector

• Keylock, Speaker, Reset, Sleep, Turbo LED and HDD LED

IDE1:Primary IDE Connector

IDE2:Secondary IDE Connector

FDD1:Floppy Controller Connector

La pagina sta caricando ...

EPOX EP-MVP3C2 Manuale utente

Questo manuale è adatto anche per

EPOX EP-MVP3C2 Manuale utente

in altre lingue

Documenti correlati

Altri documenti