Sentiotec Pro C3 Manuale utente

Version 11/22 Ident-Nr. ST-M-00007-00

Sauna control unit PRO C

new function „Door sensor“

Supplement / change to the operating instructions:

PRO-C2 /1-015-448 , PRO-C3 /1-015-451 Version 12/21

Product manual you can nd at: https://www.sentiotec.com/downloads or

The new function ensures optimal door monitoring for remote control!

Optionale accessories: Door sensor home SAB00103 / 1-052-723

The connection position of

STB and OSG were exchanged!

Note the change in the above product manual under the following points:

5.5. Installing bench sensor (clamp red wires at STB)

5.8. Connecting safety device or NEW connecting door sensor

8. Starting up

Remote start release:

●As standard the function selection switch is in the OFF position.

The remote star is operated using „Standby for remote control“.

●If you want to enable the remote start output for various devices (e.g.

coinoperated unit, remote start system), set the function selection

switch 4 in the ON position

8.2. Settings in the technician menu

Activate door sensor

1. Open the technician menu (press the lower bottom knob and the ON/OFF switch at the same time)

2. Activate the door-function

If the remote start enable is switched ON, the door sensor must be activated. To do this, carry out

the following steps:

a. Turn the top knob to the remote start symbol

►The remote start symbol ash

►In the top display „SdO“ appears

►In the bottom display „SAFE“ appears (= Standard setting)

EN

NEW

STB

Heating period

limit

Phase

alignment

Remote start

release

Status output

Light mode

Not assigned

Additional out-

put mode

OFF

OSG

STBOSG

Function selection switch

- Standard setting

DE

EN

Additional sheet for instructions for use p. 2/2

b. Turn the lower knob to the right

►In the lower display “door“ appears

3. Exiting the technician menu (Longpress on the lower knob)

10. Operation

Activating „Standby for remote operation“ with door sensor

1. Turn the top knob to the remote start symbol

►In the lower display „oFF“ appears

►The remote start symbol ash.

2. Press the lower knob

►A countdown of 30 seconds is shown in the lower display. During this time, the door can be opened/

closed as often as you like. After the countdown has expired, the door must be closed!

►In the lower display „rc“ appears

►The sauna control is now ready to be started and stopped once via a remote start signal = Mode

„Standby for remote operation“

Door is opened - warning „door“ appears in the display

- at mode „Standby for remote operation“:

To continue the mode, the door must be closed and the lower button has to be press two times.

► The countdown (30 sec.) is shown again in the lower display.

- in operation or enable remot start output (for coinoperated unit or door sensor system):

The acknowledgment takes place automatically when the door is closed.

11. User programm

The settings in the user programs has been added with the function runtime (hours) . A runtime of 2 hours is

stored in all preset user programs and can be changed as described under „Creating your own user programs“.

additional to PRO C3:

8.2. Settings in the technician menu

Setting the runtime of the post-drying programme

1. Open the technician menu (press the lower bottom knob and the ON/OFF switch at the same time)

2. Turn the top knob to the humidity symbol

► The humidity symbol lights up.

► In the top display „SIn“ appears.

► In the bottom display „OFF“ appears

3. Press the lower buttom

► In the top display„dry“ appears

► In the bottom display „t60“ appears

4. Turn the lower buttom (Selection 0 - 60; 0 = post-drying progamm off , 60 = maximum runtime in minutes)

5. Exiting the technician menu (Longpress on the lower knob)

Setting option up to the set heating period limit - see starting up function selector switches 1

and 2 (standard setting 6 hours)

Version 11/22 Ident-Nr. ST-M-00007-00

Saunasteuerung PRO C

neue Funktion „Türsensor“

Ergänzung / Änderung zu den Bedienungsanleitungen:

PRO-C2 /1-015-448 , PRO-C3 /1-015-451 Version 12/21

Bedienungsanleitung unter: https://www.sentiotec.com/downloads oder

Die neue Funktion gewährleistet die eine optimale Türüberwachung bei Fermwirken!

optionales Zubehör: Türsensor Home SAB00103 / 1-052-723

Die Anschlussposition von

STB und OSG wurden getauscht!

Beachten Sie die Änderungen in den oben angeführten Bedienungsanleitungen unter folgenden Punkten:

5.5. Ofenfühler anschließen (rote Leitungen an STB anklemmen)

5.8. Sicherheitsabschaltung anschließen bzw. NEU Türsensor

8. Inbetriebnahme

Fernstart-Freigabe:

●Standardmäßig bendet sich der Funktionswahlschalter 4 in OFF-

Position. Der Fernstart wird mittels „Standby für Fernwirken“ aktiviert.

●Wenn Sie den Fernstart-Ausgang für div. Geräte (wie z.B. Münzer,

Türsensor-System) freischalten möchten, bringen Sie den Funkti-

onswahlschalter 4 in ON-Position.

8.2. Einstellungen im Technikermenü

Türsensor aktivieren

1. Rufen Sie das Techniker-Menü auf (beim Einschalten gleichzeitig den unteren

Drehknopf und EIN/AUS drücken

2. Aktivieren Sie die Door-Funktion

Standardmäßig bendet sich der Funktionswahlschalter 4 in OFF-Position.

Zur Aktivierung des Türsensors, führen Sie folgende Schritte durch:

a. Drehen Sie den oberen Drehknopf auf das Fernstartsymbol

►Das Fernstartsymbol blinkt.

►Im oberen Display erscheint „SdO“

►Im unteren Display erscheint „SAFE“

NEU

STB

Heizzeitbe-

grenzung

Phasen-

rollierung

Fernstart-

Freigabe

Status Ausgang

Licht-

Modus

Nicht belegt

Zusatzausgang-

Modus

OFF

OSG

STBOSG

Funktionswahlschalter-

Standardeinstellung

DE

Zusatzblatt zur Bedienungsanleitung S. 2/2

b. Drehen Sie den unteren Drehknopf nach rechts

►Im unteren Display erscheint “door“

3. Verlassen Sie das Technikermenü (Longpress auf unteren Drehregler)

10. Bedienung

Standby für Fernwirken (mit Türsensor) aktivieren

1. Drehen Sie den oberen Drehknopf auf das Fernstartsymbol

►Im unteren Display wird „oFF“ angezeigt

►Das Fernstartsymbol leuchtet

2. Drücken Sie den unteren Drehknopf

►Im unteren Display wird ein Countdown von 30 Sekunde angezeigt. Die Tür kann in dieser Zeit

beliebig oft geöffnet / geschlossen werden. Nach Ablauf des Countdown muss die Türe geschlos-

sen sein!

►Im unteren Display wird „rc“ angezeigt

►Die Saunasteuerung ist nun bereit um über ein Fernstartsignal einmalig gestartet und gestopt zu

werden = Modus „Standby für Fernwirken“

Tür wird geöffnet - im Display erscheint Warnung „door“

- im Modus Standby für Fernwirken:

Um den Modus fortzusetzen muss die Tür geschlossen werden und der untere Drehknopf muss zwei mal

gedrückt werden. ► Im unteren Display wird wieder der Countdown (30 Sek.) angezeigt

- im laufenden Betrieb oder freigegebenen Fernstart-Ausgang (für Münzer oder Türsensor-System):

Die Quittierung erfolgt automatisch, wenn die Tür geschlossen wird.

11. Benutzerprogramme

Die Einstellungen in den Benutzerprogrammen wurden um die Funktion Laufzeit (Stunden) erweitert. In allen

voreingestellten Benutzerprogrammen ist eine Laufzeit von 2 Stunden hinterlegt und kann, wie unter „Eigene

Benutzerprogramme erstellen“ verändert werden.

zusätzlich bei PRO C3:

8.2. Einstellungen im Technikermenü

Nachtrockenprogramm-Laufzeit einstellen

1. Rufen Sie das Techniker-Menü auf (beim Einschalten gleichzeitig den unteren Drehknopf und EIN/AUS

drücken)

2. Drehen Sie den oberen Drehknopf auf das Feuchtesymbol

► Das Feuchtesymbol blinkt.

► Im oberen Display erscheint „SIn“.

► Im unteren Display erscheint „OFF“.

3. Drücken Sie den unteren Drehknopf

► Im oberen Display erscheint „dry“

► Im unteren Display erscheint „t60

4. Drehen Sie den unteren Drehknopf (Auswahl 0 - 60; 0 = Nachtrockenprogramm ausgesschaltet,

60 = maximale Laufzeit in Minuten)

5. Verlassen Sie das Technikermenü (Longpress auf unteren Drehregler)

Einstellmöglichkeit bis maximal der eingestellten Heizzeitbegrenzung - siehe Inbetriebnahme

Funktionswahlschalter 1 und 2 (Standardeinstellung 6 Stunden)

Version 12/21 ID no. 1-026-969

INSTRUCTIONS FOR INSTALLATION AND USE

English

EN

DE

FR

IT

NL

SV

FI

Sauna control unit

PRO C3

PRO-C3 / 1-015-451

Table of Contents

1. About this instruction manual 5

2. Important information for your safety 6

2.1. Intended use 6

2.2. Safety information for the installer 7

2.3. Safety information for the user 8

3. Product description 9

3.1. Scope of delivery 9

3.2. Optional accessories 9

3.3. Product functions 9

3.4. Sauna operating modes 11

3.5. Sensor operating modes 11

4. Installation 13

4.1. Installing the sauna control unit 13

4.2. Installing the heater sensor F1 with excess temperature fuse 15

4.3. Installing bench sensor F2 (optional) 16

4.4. Installing the humidity temperature sensor FTS2 (optional) 16

4.5. Installing the foil sensor (optional) 17

5. Electrical connection 18

5.1. Connecting the power supply cable, heater and evaporator 19

5.2. Connecting the light 19

5.3. Connecting the fan (optional) 20

5.4. Connecting the additional output (optional) 20

5.5. Connecting the power booster (optional) 20

5.6. Connecting heater sensor F1 21

5.7. Installing bench sensor F2 (optional) 21

5.8. Installing humidity temperature sensor FTS2 (optional) 21

5.9. Connectingthelmsensor(optional) 21

5.10. Connectingthesafetyshut-o 22

EN

5.11. Remote start 22

5.12. Status output 22

5.13. Finishing installation 22

6. Performing tests 23

7. Connection diagram 24

8. Starting up 25

8.1. Function selection switch settings 25

8.2. Settings in the technician menu 27

9. Operating elements 32

9.1. Description of the operating elements 32

9.2. The function selector 32

9.3. The intensity selector 33

10. Operation 33

10.1. Switching on the light 33

10.2. Switching on the sauna control unit 34

10.3. Starting sauna mode 34

10.4. Starting combi mode 35

10.5. Starting additional output 36

10.6. Switching on the light 38

10.7. Starting the fan 39

10.8. Setting the preset time 40

10.9. Cancelling the preset time function 41

10.10. Setting the duration 41

10.11. Activating standby for remote operation 42

10.12. Changing the preset values 42

10.13. Cancelling the post-drying programme 43

10.14.Switchingofunctions 43

10.15.Switchingothesaunacontrolunit 43

11. User program 44

11.1. Preset user programs 44

11.2. Accessing user programs 45

11.3. Creating your own user programs 45

12. The Eco-function 47

13. Cleaning and maintenance 48

13.1. Cleaning 48

13.2. Maintenance 48

14. Disposal 48

15. Troubleshooting 49

15.1. Error messages 49

15.2. Low-water display 50

15.3. Fuses 50

16. Technical data 51

EN

Instructions for installation and use p. 5/52

1. About this instruction manual

Read these instructions for installation and use carefully and keep them within

reach of the sauna control unit. This ensures that you can refer to information

regarding your safety and regarding operation at any time.

Symbols used for warning notices

In these instructions for installation and use, a warning notice located next to

an activity indicates that this activity poses a risk. Always observe the warning

notices. This prevents damage to property and injuries, which in the worst case

may be fatal.

The warning notices contain keywords, which have the following meanings:

DANGER!

Serious or fatal injury will occur if this warning notice is not observed.

WARNING!

Serious or fatal injury can occur if this warning notice is not observed.

CAUTION!

Minor injuries can occur if this warning notice is not observed.

ATTENTION!

This keyword is a warning that damage to property can occur.

Other symbols

This symbol indicates tips and useful information.

These installation and operating instructions can also be found in the

downloads section of our website: www.sentiotec.com/downloads.

Instructions for installation and use p. 6/52

2. Important information for your safety

The sauna control unit Pro C3 has been produced in accordance

with the applicable safety regulations for technical units. However,

hazards may occur during use. Therefore adhere to the following

safetyinformationandthespecicwarningnoticesintheindividual

chapters. Also observe the safety information for the devices con-

nected.

2.1. Intended use

The sauna control unit Pro C3 is used exclusively for operating and

controlling the sauna functions in accordance with the technical data.

The sauna control unit Pro C3 may only be used for operating and

controllingasaunaheaterwhichhasbeencertiedassatisfying

the combustion test described in paragraph 19.101 of EN 60335-

2-53. If the heater does not meet this requirement, an appropriate

safetyprecautionmustbetaken(forexample:safetyshut-o,see

5.10 on page 22).

The sauna control unit Pro C3 may only be used for operating and

controlling 3 heating circuits with a maximum heating capacity of

3.5 kW per heating circuit. The maximum evaporator capacity totals

3.5 kW. The maximum additional output capacity totals 3.5 kW.

Any use exceeding this scope is considered improper use. Improper

use can result in damage to the product, in severe injuries or death.

EN

Instructions for installation and use p. 7/52

2.2. Safety information for the installer

●Installationmayonlybeperformedbyaqualiedelectricianor

similarlyqualiedperson.

●Work on the sauna control unit may only be performed when the

power has been disconnected.

● Anall-poledisconnectingdevicewithfullcut-ocompliantwith

overvoltagecategoryIIImustbettedon-site.

●The sauna control unit must be installed outside the sauna room

at a height of approx. 1.70 m or in accordance with the rec-

ommendation issued by the sauna manufacturer. The ambient

temperature must be within a range spanning -10 °C to +40 °C.

●The heater sensor must be attached in a way that it is not af-

fectedbyaowofair.

●The heater supply cable must have a minimum cross-section of

2.5 mm2 and be temperature resistant up to 150 °C.

●Also comply with the regulations applicable at the installation

location.

●For your own safety, consult your supplier in the event of prob-

lemsthatarenotexplainedinsucientdetailintheinstallation

instructions.

Instructions for installation and use p. 8/52

2.3. Safety information for the user

●The sauna control unit must not be used by children under

8 years old.

●The sauna control unit may only be used by children above 8 years

old, by persons with limited psychological, sensory or mental

capabilities or by persons with lack of experience/knowledge:

– When they are supervised.

– When they have been shown how to use the device safely

and are aware of the hazards that could occur.

●Children must not play with the sauna control unit.

●Children under 14 years of age may only clean the sauna control

unit if they are supervised.

● Forhealthreasons,donotusethesaunawhenundertheinu-

ence of alcohol, medication or drugs.

● Makesurethatnoammableobjectshavebeenplacedonthe

sauna heater before the sauna control unit is switched on.

● Makesurethatnoammableobjectshavebeenplacedonthe

heater before activating the preset time function or the stand-by

mode for the remote start.

●Make sure that no flammable objects have been placed on

or in front of the infrared lamp before the sauna control unit is

switched on.

● Makesurethatnoammableobjectshavebeenplacedonthe

heater before activating the infrared lamp or the stand-by mode

for the remote start.

●For your own safety, consult your supplier in the event of prob-

lemsthatarenotdescribedinsucientdetailintheoperating

instructions.

EN

Instructions for installation and use p. 9/52

3. Product description

3.1. Scope of delivery

●Sauna control unit

●Heater sensor with integrated excess temperature fuse

●Installation material

●Wire jumper for bridging terminals V1 and Wm for combi heaters without

low-watershut-o

3.2. Optional accessories

●Bench sensor (item number: O-F2), sensor wires 1.5 m

●Humidity temperature sensor (item number: O-FTS2), sensor wires 3 m

●Foil sensor (item number: P-ISX-FF), sensor wires 3 m

●Power booster (item number: O-S2-18 / O-S2-30)

● Safetyshut-o(itemnumber:HT-SWL)

●pronet web server (item number: PRO-NET)

3.3. Product functions

The sauna control unit Pro C3 features the following functions:

●Regulation of combi heaters with a heating output of up to 10.5 kW and

evaporator output of up to 3.5 kW in the temperature range spanning 30 °C

to 110 °C and a humidity range spanning 5 % to 100 %.

●A power booster allows the maximum contact rating to be increased from

10.5 kW to 18 kW or 30 kW.

●Optional dimming or activation of a room light (up to 100 W)

●Optional dimmer function or activation of a fan (up to 100 W)

●Remote start function

Instructions for installation and use p. 10/52

●Status output

●Preset time function (up to 24 hours)

●Additional output

Either for dimming (up to 500 W), switching (up to 3.5 kW) or regulating the

sauna room temperature via the additional output.

The additional output has no excess temperature fuse. For this reason, only

intrinsically safe devices should be operated using the additional output.

– If infrared heaters are connected to the additional output, these must

have an excess temperature fuse. We recommend using the following

infrared lamps:

●DIR-350-R, WIR-350-R, DIR-500-R, WIR-500-R, DIR-750-R,

WIR-750-R, DIR-1300-R, WIR-1300-R

●ECO-350-R, ECO-350-G, ECO-500-R, ECO-500-G, ECO-750-R

– If one of the following infrared heat plates is connected to an additional

output, the foil sensor P-ISX-FF must be used, and must be activated

in the technician menu (see 8.2. Settings in the technician menu on

page 27):

●IR-WP-100, IR-WP-175, IR-WP-390, IR-WP-510

●IR-WPHL-100, IR-WPHL-175, IR-WPHL-390, IR-WPHL-510

●User program

The user program enables favourite sauna settings to be saved and accessed

again.Thereare5presetuserprogramsavailablewhichcanbemodied

according to user requirements.

●Automatic heating period limiter

The sauna control unit shuts down automatically after the maximum heating

period for safety reasons. The maximum heating period can be set to 6 h,

12 h, 18 h or 24 h.

●Post-drying programme

Oncecombi-modehasnished,thepost-dryingprogrammestartsautomati-

cally to prevent mould or rot from forming in the sauna room. This involves

heating the sauna room to 80 °C with the fan running for 30 minutes.

EN

Instructions for installation and use p. 11/52

●Excess temperature fuse

The excess temperature fuse is installed in the housing for the heater sen-

sor. Should the sauna heater continue heating after reaching the preferred

temperature due to a defect, the excess temperature fuse switches the sauna

heateroatatemperatureofapprox.139°C.

3.4. Sauna operating modes

The sauna control unit Pro C3 provides two operating modes, sauna mode and

combi mode.

Sauna mode

Dry heat is provided in sauna mode. The temperature in the room is high (80 to

100 °C) The humidity level of maximum 10 % is low.

Combi mode

The evaporator operates along with the sauna heater in combi mode. The

temperature in the sauna room is lower (approx. 40 to 65 °C) than in sauna

mode, with the relative humidity being considerably higher, spanning 35 % to

approximately 70 %. The maximum humidity level which can be set depends on

the temperature of the sauna. The higher the sauna temperature, the lower the

maximum humidity level which can be set.

3.5. Sensor operating modes

The sauna control unit can be operated with one or two sensors. A temperature

sensor (bench sensor, F2) or a humidity sensor (FTS2) can be used as the

second sensor.

Single-sensor mode (F1)

Single-sensor mode must be activated in the technician menu (see 8.2. Settings

in the technician menu on page 27).

In single-sensor mode, the sauna control unit is operated with the heater sensor

with excess temperature fuse (F1) only. This is included in the scope of delivery.

Instructions for installation and use p. 12/52

In single-sensor mode, the sauna control unit only displays the set temperature

as standard. The actual temperature is not displayed. Should the sauna control

unit display the temperature above the heater (F1) as an actual temperature in

single-sensormode,itmustbeactivatedwhenstartingupforthersttime(see

8.2. Settings in the technician menu on page 27)

The maximum humidity level which can be set in single-sensor mode is based

on the temperature above the heater and the humidity is timed. Only the set

value for the humidity level (in % of relative humidity) is displayed by the sauna

control unit. The actual humidity level in the sauna room when humidity is timed

depends on the size of the room and the evaporator capacity, and may deviate

from the set value.

Two-sensor mode with bench sensor (F2)

In two-sensor mode with bench sensor, a second temperature sensor (bench

sensor) is installed above the rear sauna bench. The sauna control unit displays

the temperature measured by the bench sensor as the actual temperature.

In two-sensor mode with bench sensor, the humidity is timed. Only the set

value for the humidity level (in % of relative humidity) is displayed by the sauna

control unit. The actual humidity level in the sauna room when humidity is timed

depends on the size of the room and the evaporator capacity, and may deviate

from the set value.

Two-sensor mode with humidity temperature sensor (FTS2)

When a humidity temperature sensor is used in two-sensor mode, the sauna

control unit displays the temperature which is measured by the humidity tem-

perature sensor as the actual temperature.

In two-sensor mode with humidity temperature sensor, the evaporator is regu-

lated in accordance with the humidity level measured in the sauna room. The

actual value for the humidity level (in % of relative humidity) is displayed by the

sauna control unit.

EN

Installation instructions, only for experts p. 13/52

4. Installation

4.1. Installing the sauna control unit

Observe the following points when installing the sauna control unit:

●The sauna control unit must be installed outside the sauna room or in accord-

ance with the recommendation issued by the sauna manufacturer.

●The ambient temperature must be within a range spanning -10 °C to +40 °C.

●The sensors may only be connected using the sensor wires provided with the

unit, which are heat-resistant up to 150 °C.

ATTENTION!

Damage to the unit

The sauna control unit is protected against jets of water, however direct contact

with water could still damage the unit.

●Install the sauna control unit in a dry place at which a maximum humidity of

95 % is not exceeded.

The sensor wires may be extended under the following conditions:

●When a silicon wire resistant to temperatures up to 150 °C is used.

●The minimum cross-section of the wire is 0.5 mm2.

●The length of the heater sensor wires may NOT exceed 10 m.

ATTENTION!

Sources of interference can have a negative eect on signal transmission

●Lay all sensor wires separately from other mains wires and control wires.

●Protect wires with only one layer of insulation by using a pipe (double insulation).

Installation instructions, only for experts p. 14/52

Fig. 1 Position of the attachment device and the installation holes

(dimensions in mm)

C

To install the sauna control unit, perform the following steps:

1. Screw two Phillips-head screws (16 mm) into the wall of the sauna at a height

of approx. 1.70 m to a distance of up to 7 mm. The two screws must be

placed at a distance of 145 mm from each other (see Fig. 1).

2. Press the clip locks C in lightly using a screwdriver and remove the cover

from the housing (see Fig. 2).

3. Fasten the sauna control unit onto the Phillips-head screws using the at-

tachment device A as an aid (see Fig. 1).

4. Screw two Phillips-head screws (16 mm) into the lower fastening holes B

(see Fig. 1).

82

80

34

175

145

34

43

40

A

B

Fig. 2 Removing the cover from the housing

EN

Installation instructions, only for experts p. 15/52

4.2. Installing the heater sensor F1 with excess temperature fuse

Observe the following points when installing the heater sensor:

●The heater sensor must be installed on the rear of the heater, above the mid-

dle of the sauna heater. An interval of approx. 15 cm to the roof of the sauna

room must be maintained.

● Theheatersensormustbeattachedinawaythatitisnotaectedbyaow

of air.

To install the heater sensor, perform the following steps (see Fig. 3):

1. Lay the two 2-pin heater sensor wires in the wall of the sauna room, leading

themtotheheatersensorinstallationlocationandaxtheheatersensor

wires using wire clips.

2. Pull the two half-shells 1 of the heater sensor apart.

3. Connect the four connectors for the heater sensor wire 5 in accordance

with the Fig. 3.

4. Place the connection panel 2 crossways (as shown in Fig. 3) in the heater

sensor half-shells.

5. Place the two half-shells together, screw them together using the two Phillips-

head screws 3 (9 mm) and check whether the heater sensor has been

securely closed.

6. Install the heater sensor on the rear of the heater using the two wood screws

enclosed 6 (16 mm).

1 Heater sensor half-shells

2 Connection panel

3 Phillips-head screws (9 mm)

4 Heater sensor

5 Heater sensor wires

6 Wood screws (16 mm)

Fig. 3 Installing the

heater sensor

Red

White

Red

Installation instructions, only for experts p. 16/52

4.3. Installing bench sensor F2 (optional)

The bench sensor must be installed on the wall of the sauna room, above the

rear bench seat. An interval of approx. 15 cm to the roof of the sauna room must

be maintained.

To install the bench sensor, perform the following steps:

1. Lay the two 2-pin bench sensor wires in the wall of the sauna room, leading

themtothebenchsensorinstallationlocationandaxthebenchsensor

wires using wire clips.

2. Pull the two half-shells of the bench sensor apart.

3. Connect the two connectors for the bench sensor wire to the two middle

terminals on the connection panel.

4. Place the connection panel crossways in the bench sensor half-shells.

5. Place the two half-shells together and screw them together using the two

Phillips-head screws (9 mm).

6. Check whether the bench sensor has been securely closed.

7. Install the bench sensor on the wall of the sauna room using the two wood

screws enclosed (16 mm). Maintain an interval of 15 cm to the roof of the

sauna room.

4.4. Installing the humidity temperature sensor FTS2 (optional)

The humidity temperature sensor must be installed on the wall of the sauna room

above the rear bench seat. A distance of approx. 15 cm to the roof of the sauna

must be maintained.

To install the humidity temperature sensor, perform the following steps:

1. Lay the two 5-pin bench sensor wires in the wall of the sauna room, leading

themtothehumiditytemperaturesensorinstallationlocationandaxthe

sensor wires using wire clips.

2. Install the humidity temperature sensor to the wall of the sauna room using

the two wood screws enclosed (16 mm). Maintain an interval of 15 cm to

the roof of the sauna room.

La pagina sta caricando ...

Sentiotec Pro C3 Manuale utente

Sentiotec Pro C3 Manuale utente

in altre lingue

Documenti correlati

Altri documenti