DREAME VVN5 Manuale utente

Dreame

Cordless Vacuum Cleaner

User Manual

Merci d’avoir choisi L’aspirateur

Sans Fil Dreame 21

Dreame Cordless Vacuum Cleaner

User Manual 1

Dreame Bedienungsanleitung für

kabellosenStaubsauger 42

Приятного пользования!

Беспроводной пылесос Dreame 62

Benvenuto in Dreame - aspirapolvere

senza 󼴩li 84

Manual de usuario de la aspiradora

inalámbrica Dreame 102

122

144

1

Safety Instructions

Warning

To prevent accidents including electric shock or 󼴩󼴩re caused by improper use, please

read this manual carefully before use and retain it for future reference.

This product can be used by children aged from 8 years and above and persons with

physical, sensory, intellectual de󼴩ciencies, or limited experience or knowledge under

the supervision of a parent or guardian to ensure safe operation and to avoid any

risk of hazards. Cleaning and maintenance shall not be made by children without

supervision.

The vacuum cleaner is not a toy. Children shall not play with or operate this product.

Please exercise caution when using the vacuum cleaner near children. Do not allow

children to clean or maintain the vacuum cleaner unless supervised by a parent or

guardian.

Do not use the vacuum cleaner outdoors or on wet surfaces. Only use the vacuum

cleaner on dry indoor surfaces. Do not touch the plug or any part of the vacuum

cleaner with wet hands.

To reduce the risk of 󼴩re, explosion, or injury, check to make sure the lithium battery

and charging adapter are undamaged before use. Do not use the vacuum cleaner if

either the lithium battery or charger is damaged.

The soft roller nozzle, battery, metal connector pin, and vacuum cleaner are

electrically conductive and should not be immersed in water or other liquid. Make

sure to dry all 󼴩lters after cleaning.

To prevent injury caused by moving parts, turn oﬀ the vacuum cleaner before

cleaning the soft roller nozzle. The soft roller brushbar, dust compartment, and 󼴩lter

must all be properly installed before using the vacuum cleaner.

Only use the original charging adapter. Never use an unoriginal adapter, as this may

cause the lithium battery to catch 󼴩re.

Do not use the vacuum cleaner to pick up ﬂammable or combustible liquids, such as

gasoline, or bleach, ammonia, drain cleaners or other liquids.

Do not use the vacuum cleaner to pick up drywall particles, ashes like 󼴩replace ash,

or smoking or burning materials such as coal, cigarette butts or matches.

Do not use the vacuum to pick up sharp or hard objects, such as glass, nails, screws,

or coins, which may damage the machine.

Keep hair, loose clothing, 󼴩ngers and other parts of the body away from the vacuum

cleaner's openings and moving parts. Do not point the hose, wand or tools at your

eyes or ears or put them in your mouth.

2

Do not put any object into the vacuum's openings. Do not use the vacuum cleaner

with any opening blocked. Keep free of dust, lint, hair, or other items which may

reduce airﬂow.

Do not rest the vacuum cleaner against a chair, table, or other unstable surface, as

this may cause damage to the machine or personal injury. If the vacuum cleaner

becomes damaged from being knocked over or is otherwise malfunctioning, please

contact our authorized service department. Never attempt to disassemble the device

on your own.

All instructions in the manual for recharging the battery must be strictly followed.

Failure to properly charge the battery within the speci󼴩ed temperature range could

damage the battery.

Only use accessories and replacement parts that are approved by Dreame.

Do not use the vacuum cleaner without the clear dust compartment and 󼴩lter in

place.

Make sure the vacuum is unplugged when not used for extended periods as well as

prior to performing any maintenance or repairs.

Please be extra careful when using the vacuum cleaner to clean stairs.

Do not install, charge, or use this product outdoors, in bathrooms, or around a pool.

Fire Hazard Warning: Do not apply any type of fragrance to the vacuum cleaner's

󼴩lter. These types of products are known to contain ﬂammable chemicals which may

cause the vacuum cleaner to catch 󼴩re.

This product is designed for home use only.

We Dreame Technology (Tianjin) Limited, hereby, declares that this equipment is in

compliance with the applicable Directives and European Norms, and amendments.

The full text of the EU declaration of conformity is available at the following internet

address: www.dreame.tech

means detachable supply unit

3

Product Overview

Part Names

Display Screen

HEPA Filter Assembly

Extension Rod

Release Button

Brushbar Head

Release Button

Extension Rod

Soft Roller Nozzle

Charging Port

On/Oﬀ Switch

· Push to turn on

· Release to turn oﬀ

Dust Compartment

Release Button

Cyclone Assembly

4

Product Overview

Accessories

Extension Rod

Power Adapter 2-in-1 Crevice

Nozzle

Extension Hose 2-in-1 Brush

Nozzle

Soft Roller Nozzle Mini-Motorized

Nozzle

2-in-1 Charging &

Storage Mount

( Including screws ×2,

wall plugs ×2）

5

Installation

Vacuum and Accessories

Installation Diagram

6

Installation

Vacuum and Accessories

Installation Diagram

7

Installation

Installing the 2-in-1 Charging & Storage Mount

1. The 2-in-1 charging & storage mount is an optional accessory, you can install it

based on your requirements.

2. The mount should be installed in a cool, dry place near a power outlet, out of

direct sunlight, and away from moisture-prone areas, such as a kitchen.

3. Securely install the mount using mounting hardware suitable for the type of wall

selected. Make sure the installation area is clear of any pipes such as gas or water

lines, and air ducts, electric wires and cables, or drainage lines.

4. It is recommended to hire a professional to install the mount and to use protective

clothing, goggles, and other protective equipment where necessary.

5. Using an electric drill, mark and drill two 8 mm diameter holes into the wall where

desired to a depth of about 30 mm. Insert the wall plugs into the holes, position the

mount, then fasten it to the wall with the included screws.

106 cm

8

Charging

Note:

• Fully charge the vacuum cleaner before using it for the 󼴩rst time. This will take

about 3.5 hours.

• Vacuum cleaner cannot be used while charging.

• Vacuuming at turbo mode for a prolonged period will cause the battery to heat

up, which increases charging time. Allow the vacuum cleaner to cool down for 30

minutes before charging it.

Battery Status Indicator

Note:

Once the vacuum cleaner is fully charged, the indicator will turn oﬀ after 5 minutes,

and the vacuum cleaner will enter the energy-saving mode.

Oﬀ Blinking On

Low battery

Half battery

Nearly full

Fully charged

9

How to Use

Function introduction of display screen

Electronic lock / Reset 󼴩lter

·Click to switch Working Mode

·Press and hold for 1.5 seconds to enter the

󼴩lter reset interface

Battery level monitor ring

·Blue: Battery level is more than 20%

·Red: Battery level is less than < 20%

Gear switch / Language setup

·Click to switch Eco Mode、Med Mode、

Turbo Mode

·Press and hold for 3 seconds to enter the

language setting interface

Note: If you need to pay attention to any abnormality during the use of the product,

the screen will push a prompt message. You should follow the instructions on the

screen to keep the performance normal.

You may set the display prompt language (Simpli󼴩ed English is the default when you

start the machine) by the following methods as you need.

Language setup

Note: If there is no operation for more than 5 seconds, it will automatically exit from

the language setting interface, and the display information will be oﬀ.

a.Press and hold for 3 seconds to enter the

language selection interface

b.Click to scroll through the language list, select

the appropriate language

c.Press and hold for 3 seconds to save your

setting setting.

10

How to Use

Cleaning Mode

Mode 1: Discontinuous Cleaning Mode

Press and hold the switch of the vacuum cleaner to start working, and release it to

stop immediately.

Mode 2: Continuous Cleaning Mode (Electronic lock)

In standby mode, click the electronic lock key to switch to Continuous Cleaning

Mode, and then brieﬂy press the switch to make the vacuum cleaner in Continuous

Cleaning Mode.

Use the electronic lock to free your 󼴩ngers and avoid 󼴩nger fatigue caused by holding

the switch.

Note:

• In this mode, brieﬂy press the switch to suspend the operation or start agian，

and the working mode of the vacuum cleaner will not change.

• Click the electronic lock again to quit the Continuous Cleaning Mode.

There are two working modes for the vacuum cleaner, which can be selected

according to your own needs.

11

How to Use

Using Di󼴨erent Attachments

Soft Roller Nozzle

Suitable for vacuuming wood, tile,

marble, and other hard ﬂoor surfaces as

well as for vacuuming up larger pieces of

dirt and debris.

The soft roller nozzle can also be directly

attached to the vacuum cleaner.

2-in-1 Brush Nozzle

Suitable for vacuuming up dust

and mites on beds, sofas, and other

furniture fabric.

Mini-Motorized Nozzle

Strong vibrations yield deep cleaning

action for removing mites and dust

from mattresses and fabric surfaces.

2-in-1 Crevice Nozzle

Suitable for vacuuming cracks, corners

of doors and windows, stairs, and other

hard-to-reach places.

Reset ﬁlter

Press and hold for 5

seconds to enter the ﬁlter

reset countdown screen.

When appears on the

screen, it indicates that the

reset is successful.

The battery runs out

Please charge as soon as

possible.

Battery Error

Please contact our

after-sales service

personnel for

maintenance.

更换滤芯

参考维护保养【清洁滤

芯】部分拆下滤芯更换。

Replace the ﬁlter

Refer to the maintenance

manual [Cleaning HEPA

Filter] section to remove

the ﬁlter and replace it.

Low battery capacity

Please charge as soon as

possible.

Battery overheating

Please wait and

continue to use after

motor temperature is

normal.

Air duct blocked

Check whether the dust

compartment, extension

rod, and soft roller nozzle

are blocked.

Clean the brush

Refer to the maintenance

manual [Soft Roller Nozzle]

section to clean the ﬁber

material and hairs

wrapped around the roller

brush.

12

Note：

• If any rotating part becomes stuck, the vacuum may turn oﬀ automatically. Remove

any trapped foreign objects, then resume use.

• The vacuum cleaner will automatically shut oﬀ if its motor enters overheat

protection mode. Wait until the motor's temperature returns to normal before

resuming use.

How to Use

Extension Hose

use for hard-to-reach corner cleaning.

Reset ﬁlter

Press and hold for 5

seconds to enter the ﬁlter

reset countdown screen.

When appears on the

screen, it indicates that the

reset is successful.

The battery runs out

Please charge as soon as

possible.

Battery Error

Please contact our

after-sales service

personnel for

maintenance.

更换滤芯

参考维护保养【清洁滤

芯】部分拆下滤芯更换。

Replace the ﬁlter

Refer to the maintenance

manual [Cleaning HEPA

Filter] section to remove

the ﬁlter and replace it.

Low battery capacity

Please charge as soon as

possible.

Battery overheating

Please wait and

continue to use after

motor temperature is

normal.

Air duct blocked

Check whether the dust

compartment, extension

rod, and soft roller nozzle

are blocked.

Clean the brush

Refer to the maintenance

manual [Soft Roller Nozzle]

section to clean the ﬁber

material and hairs

wrapped around the roller

brush.

13

How to Use

If you need to pay attention to any abnormality during the use of the product, the

screen will push a prompt message. You should follow the instructions on the screen

to keep the performance normal.

14

Care & Maintenance

Tips:

1. Always use genuine parts to keep your warranty from being voided.

2. If the 󼴩lter or nozzle becomes clogged, the vacuum will stop working shortly after

being turned on. To restore functionality, clean the 󼴩lter or nozzle.

3. If the vacuum will not be used for an extended period, fully charge it, unplug its

power adapter, and store it in a cool, low-humidity environment away from direct

sunlight. To avoid over-discharging the battery, recharge the vacuum at least

once every 3 months.

Cleaning the Vacuum Cleaner

Wipe the vacuum with a soft dry cloth.

Cleaning the Dust Compartment

Before cleaning the dust compartment, disconnect the adapter and keep the

vacuum's power switch in the oﬀ position. The vacuum's cleaning ability will be

reduced if the dust compartment is 󼴩lled to the "MAX" mark. To regain performance,

empty the compartment.

1. To empty the dust compartment: Press the release button on the bottom of the

compartment, then empty its contents.

2. Clean the dust compartment: Use a dry cloth or paper towel to wipe the dust from

the inner wall of the dust compartment.

15

Care & Maintenance

1.Rotate the cyclone assembly in the direction illustrated to unlock it, then remove

the cyclone assembly.

Note:Remove Cyclone Separator from the housing by turning in the direction as

shown in the diagram for a thorough cleaning.

2. Rinse the cyclone assembly with water until it is clean. To thoroughly dry the

cyclone assembly,

Note:Keep it in a ventilated or cool place for at least 24 hours.

2

3

1

12

6

111

57

210

48

39 24 hrs

Cleaning the Cyclone Assembly

16

1. Place the vacuum cleaner securely on a ﬂat surface, then turn the HEPA 󼴩lter

assembly cover in the direction indicated and remove the HEPA 󼴩lter assembly.

Note: Remove the built-in foam pad before cleaning the HEPA 󼴩lter assembly. Rinse

the HEPA 󼴩lter and foam pad with water.

2.Rinse the HEPA filter and foam pad with water. To thoroughly remove all dust

caught in the 󼴩lter, rotate the HEPA 󼴩lter by 360 degrees while rinsing. Lightly tap the

󼴩lter against a sink several times to remove any excess debris.Keep the HEPA 󼴩lter in

a well-ventilated and cool place to fully dry.

Note: Fully dry the 󼴩lter (at least 24 hours) before reinstalling it.

1

2

3

12

6

111

57

210

48

924 hrs

Care & Maintenance

Cleaning the HEPA Filter Assembly

17

Cleaning the Soft Roller Brushbar

1. Push the brushbar head release

button in the direction of the arrow until

the cover of the brushbar head pops to

open, then remove the brushbar head

by lifting it in the direction indicated.

2. Use scissor to cut oﬀ the hairs and

󼴩bers that stick on the brushbar head.

Wipe the dust from the notch and

transparent cover with a dry cloth or

paper towel.

3. When it is dirty, rinse the brushbar

head with clean water until it is clean.

4. Stand the brushbar head upright for

at least 24 hours until it is fully dry.

12

6

111

57

210

48

39 24 hrs

12

6

111

57

210

48

39 24 hrs

12

6

111

57

210

48

39 24 hrs

Care & Maintenance

18

Cleaning the Electric Mite Brush

1. Use a coin as illustrated to rotate the

lock counterclockwise until you hear a

click.

Note: It is recommended to clean the

electric mite brush after each use.

3. Stand the brush head upright in a

well-ventilated area for at least 24 hours

until it is fully dry.

2. After unlocking the brush head,

remove it from the electric mite brush,

then rinse and clean the brush head.

4. Once the soft roller brushbar is dry,

reinstall it by following the disassembly

steps in reverse.

12

6

111

57

210

48

39 24 hrs

Care & Maintenance

La pagina sta caricando ...

DREAME VVN5 Manuale utente

DREAME VVN5 Manuale utente

in altre lingue

Documenti correlati

Altri documenti