Scalable airFiber
®
MIMO Multiplexer
Models: AF-MPx4, AF-MPx8
Introduction
Thank you for purchasing the Ubiquiti Networks® airFiberNxN
MIMO Multiplexer. This Quick Start Guide is designed to guide
you through installation and also includes warranty terms.
Package Contents
or
AF-MPx4
airFiber NxN Multiplexer
AF-MPx8
airFiber NxN Multiplexer
Ubiquiti Networks, Inc. www.ubnt.com
Ubiquiti Networks, Inc. www.ubnt.com
4x4 Radio Bracket 8x8 Radio Bracket* Protective Shrouds
(Left and Right)
Scalable airFiber
®
MIMO Multiplexer
Models: AF-MPx4, AF-MPx8
M4x12 Screws
(Qty. 2)
M3x8 Screws*
(Qty. 4)
Quick Start Guide
* Only included with the AF-MPx8.
TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet
cable and earth grounding must be used as conditions of product warranty. TOUGHCable
™
is designed for outdoor installations. It is the customer’s responsibility to follow local country
regulations, including operation within legal frequency channels, output power, and Dynamic
Frequency Selection (DFS) requirements.
airFiber X Compatibility
The airFiber NxN is designed for use with airFiber 5X radios,
(model AF-5X) and 5 GHz airFiber X or RocketDish
™
antennas.
Note: The airFiber X Antenna OMT Conversion Kit
(AF-5G-OMT-S45) is highly recommended when using a
RocketDish for proper fitting and improved frequency
isolation.
Installation Requirements
• (2) airFiber 5X radios for AF-MPx4
• (4) airFiber 5X radios for AF-MPx8
• airFiber X or RocketDish antenna
• Clear view of the sky for proper GPS operation
• Ground wires – min. 10 AWG (5 mm
2
) and max. length:
1m. Asa safety precaution, ground the airFiber radios to
grounded masts, poles, towers, or grounding bars.
WARNING: Failure to properly ground your
airFiber radio will void your warranty.
Note: For guidelines about grounding and
lightning protection, follow your local electrical
regulatorycodes.
• Outdoor, shielded Category 6 (or above) cabling and
shielded RJ-45 connectors are required for all wired
Ethernetconnections.
Hardware Overview
airFiber NxN Multiplexer
Chain 0 Chain 1
RF Cables
(AF-MPx8 Shown)
Chain 0 Connect the antenna RF +45° to this connector.
Chain 1 Connect the antenna RF -45° to this connector.
RF Cables Connect each RF Cable pair to the corresponding
RFconnection chain on each airFiber 5X radio. For example,
connect cable A0 to Chain 0, and cable A1 to Chain 1.
Configure the airFiber 5X Radio
Note: The airFiber 5X radios must be running airOS®F
v3.2.1 or newer. The latest firmware is available at:
downloads.ubnt.com/airfiber
Each airFiber 5X radio must be preconfigured for use with the
airFiberNxN before installing them at the site. Configuration
details are available in the airFiber X User Guide, available at:
downloads.ubnt.com/airfiber
Enable airFiber NxN support on each radio:
1. Log into the airOS F Configuration Interface.
2. Click the Wireless tab.
3. Enter the additional Cable Loss value (dB):
a. 4.1 for the AF-MPx4, or
b. 7.2 for the AF-MPx8
4. For the NxN Radio setting, select Enable.
5. Click Change, and then click Apply.
Hardware Installation
The following installation shows the AF-MPx8. For the
AF-MPx4 installation, only the mounting and connecting of
two airFiber 5X radios apply.
1. (For AF-MPx8 only) Attach the 8x8 Radio Bracket to the 4x4
Radio Bracket using four M3x8 Screws.
2. Seat the airFiber NxN Multiplexer into the 4x4 Radio Bracket
either at (a) a 15° angle or (b) vertically:
a. For most antenna models, the airFiber NxN Multiplexer
should be installed at a 15° angle. Insert the airFiber NxN
Multiplexer from behind the 4x4 Radio Bracket and slide
the 15° Angle Tabs into the slots on the bracket.
15° Angle Tab
b. For other antenna configurations that require the
airFiber NxN assembly to be mounted to a pole, the
airFiber NxN Multiplexer must be installed vertically.
Insert the airFiber NxN Multiplexer from behind the 4x4
Radio Bracket and slide the Vertical Tabs into the slots
on the bracket.
Vertical Tab
3. Secure the airFiber NxN Multiplexer to the 4x4 Radio Bracket
using two M4x12 Screws.
Note: Ensure the airFiber 5X radios are preconfigured
and the ground wires are installed as outlined in the
radio’s Quick Start Guide before mounting the radios.
4. Mount the airFiber 5X radios to the 4x4 Radio Bracket:
a. Align the mounting tabs on the back of the radio with
the mounting bracket.
b. Slide the radio down to lock it into place.
Ubiquiti Networks, Inc. www.ubnt.com
Ubiquiti Networks, Inc. www.ubnt.com
5. Mount the airFiber 5X radios to the 8x8 Radio Bracket:
a. Align the mounting tabs on the back of the radio with
the mounting bracket.
b. Slide the radio down to lock it into place.
Ubiquiti Networks, Inc. www.ubnt.com
Ubiquiti Networks, Inc. www.ubnt.com
*640-00230-02*
640-00230-02
6. Connect the RF Cables to the airFiber 5X radios. Connect
each RF Cable pair to the corresponding RFconnection
chain on each radio. For example, connect cable A0 to
Chain 0, and cable A1 to Chain 1.
7. Attach the airFiber NxN assembly to the airFiber X or
RocketDish antenna:
a. Align the mounting tabs on the back of the airFiber NxN
Multiplexer with the mounting bracket.
b. Slide the airFiber NxN Multiplexer down to lock it into
place on the bracket.
Note: The airFiber NxN assembly may be pole-mounted
if it cannot be attached to the antenna. See the
Pole-Mounting section for details.
8. Connect the RF cables from the antenna to the RF
connectors on the airFiber NxN Multiplexer. Connect +45° to
Chain 0 and -45° to Chain 1.
9. Attach the GPS antennas to each of the airFiber 5X radios.
10. Mount the GPS antennas in a location that has a clear view
of the sky, and is above and as far away from the radios as
possible.
11. Attach the Protective Shrouds:
a. Insert the Protective Shroud’s attachment tab between
the airFiber 5X radio and the 4x4 Radio Bracket.
b. Push the Protective Shroud down until the attachment
tab locks into place.
12. Secure the grounding wire from each radio to a grounded
mast, pole, tower, or grounding bar.
WARNING: Failure to properly ground your
airFiber radio will void your warranty.
Note: The ground wire should be as short as
possible and no longer than one meter in length.
Pole-Mounting
1. Ensure the airFiber NxN Multiplexer is installed vertically in
the 4x4 Radio Bracket.
2. Mount the airFiber NxN assembly to the pole using two
metal straps (not included):
a. Insert a metal strap through each mounting bracket on
the back of the airFiber NxN Multiplexer and 4x4 Radio
Bracket.
b. Secure both staps around the pole.
3. Connect the RF cables from the antenna to the
RFconnectors on the airFiber NxN Multiplexer. Connect
+45° to Chain 0 and -45° to Chain 1.
Specifications
AF-MPx4
Dimensions 197.5 x 240.9 x 103.2 mm
(7.78 x 9.48 x 4.06")
Weight 0.4 kg (0.8 lb)
RF Connectors (2) RP-SMA Weatherproof (CH0, CH1)
(4) RP-SMA Weatherproof
(A0, A1, B0, B1)
Cable Loss 4.1 dB
Supported airFiber X Radio AF-5X
Multiplex MIMO 2 x (2x2)
Mounting airFiber X/Rocket Mount Compatible
AF-MPx8
Dimensions 210.5 x 240.9 x 109 mm
(8.29 x 9.48 x 4.29")
Weight 0.45 kg (1.0 lb)
RF Connectors (2) RP-SMA Weatherproof (CH0, CH1)
(8) RP-SMA Weatherproof
(A0, A1, B0, B1, C0, C1, D0, D1)
Cable Loss 7.2 dB
Supported airFiber X Radio AF-5X
Multiplex MIMO 4 x (2x2)
Mounting airFiber X/Rocket Mount Compatible
Limited Warranty
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the
product(s) furnished hereunder (the “Product(s)”) shall be free from defects
in material and workmanship for a period of one (1) year from the date
of shipment by UBIQUITI NETWORKS under normal use and operation.
UBIQUITI NETWORKS’ sole and exclusive obligation and liability under
the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,
to repair or replace any Product that fails to conform to the above
warranty during the above warranty period. The expense of removal and
reinstallation of any Product is not included in this warranty. The warranty
period of any repaired or replaced Product shall not extend beyond its
original term.
Warranty Conditions
The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an addition made thereto,
except by Ubiquiti Networks, or Ubiquiti Networks’ authorized
representatives, or as approved by Ubiquiti Networks in writing;
(II) has been painted, rebranded or physically modified in any way;
(III) has been damaged due to errors or defects in cabling;
(IV) has been subjected to misuse, abuse, negligence, abnormal
physical, electromagnetic or electrical stress, including lightning
strikes, or accident;
(V) has been damaged or impaired as a result of using third party
firmware;
(VI) has no original Ubiquiti MAC label, or is missing any other original
Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within 30 days of issuance of
the RMA.
In addition, the above warranty shall apply only if: the product has been
properly installed and used at all times in accordance, and in all material
respects, with the applicable Product documentation; all Ethernet cabling
runs use CAT5 (or above), and for outdoor installations, shielded Ethernet
cabling is used, and for indoor installations, indoor cabling requirements
are followed.
Returns
No Products will be accepted for replacement or repair without obtaining
a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS
during the warranty period, and the Products being received at UBIQUITI
NETWORKS’ facility freight prepaid in accordance with the RMA process of
UBIQUITI NETWORKS. Products returned without an RMA number will not
be processed and will be returned freight collect or subject to disposal.
Information on the RMA process and obtaining an RMA number can be
found at: www.ubnt.com/support/warranty.
Disclaimer
EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI
NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,
SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM
AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,
EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,
REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,
ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,
SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS
FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY
WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR
TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.
BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR
ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE
TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING
THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE
SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS
AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS
FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD
PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,
DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT
CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY
OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant
that the operation of the Products will be error-free or that operation will
be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible
for damages or claims of any nature or description relating to system
performance, including coverage, buyer’s selection of products (including
the Products) for buyer’s application and/or failure of products (including
the Products) to meet government or regulatory requirements.
Limitation of Liability
EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL
UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR
DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES
(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING
OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE
PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER
LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
Note
Some countries, states and provinces do not allow exclusions of implied
warranties or conditions, so the above exclusion may not apply to you.
You may have other rights that vary from country to country, state to
state, or province to province. Some countries, states and provinces do not
allow the exclusion or limitation of liability for incidental or consequential
damages, so the above limitation may not apply to you. EXCEPT TO
THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO
NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE
MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY
SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations
Convention on Contracts for the International Sale of Goods shall not apply
to any transactions regarding the sale of the Products.
Declaration of Conformity
Česky
[Czech]
UBIQUITI NETWORKS tímto prohlašuje, že toto UBIQUITI
NETWORKS zařízení, je ve shod se základními požadavky a dalšími
příslušnými ustanoveními směrnice 1999/5/ES.
Dansk
[Danish]
Hermed, UBIQUITI NETWORKS, erklærer at denne UBIQUITI
NETWORKS enhed, er i overensstemmelse med de væsentlige krav
og øvrige relevante krav i direktiv 1999/5/EF.
Nederlands
[Dutch]
Hierbij verklaart UBIQUITI NETWORKS, dat deze UBIQUITI
NETWORKS apparaat, in overeenstemming is met de essentiële
eisen en de andere relevante bepalingen van richtlijn 1999/5/EC.
English
Hereby, UBIQUITI NETWORKS, declares that this UBIQUITI
NETWORKS device, is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
Eesti
[Estonian]
Käesolevaga UBIQUITI NETWORKS kinnitab, et antud UBIQUITI
NETWORKS seade, on vastavus olulistele nõuetele ja teistele
asjakohastele sätetele direktiivi 1999/5/EÜ.
Suomi
[Finnish]
Täten UBIQUITI NETWORKS vakuuttaa, että tämä UBIQUITI
NETWORKS laite, on yhdenmukainen olennaisten vaatimusten ja
muiden sitä koskevien direktiivin 1999/5/EY.
Français
[French]
Par la présente UBIQUITI NETWORKS déclare que l’appareil
UBIQUITI NETWORKS, est conforme aux exigences essentielles et
aux autres dispositions pertinentes de la directive 1999/5/CE.
Deutsch
[German]
Hiermit erklärt UBIQUITI NETWORKS, dass sich dieses UBIQUITI
NETWORKS Gerät, in Übereinstimmung mit den grundlegenden
Anforderungen und den anderen relevanten Vorschriften der
Richtlinie 1999/5/EG befindet.
Ελληνική
[Greek]
Δια του παρόντος, UBIQUITI NETWORKS, δηλώνει ότι αυτή η
συσκευή UBIQUITI NETWORKS, είναι σε συμμόρφωση με τις
βασικές απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας
1995/5/ΕΚ.
Magyar
[Hungarian]
Ezennel UBIQUITI NETWORKS kijelenti, hogy ez a UBIQUITI
NETWORKS készülék megfelel az alapvető követelményeknek és
más vonatkozó 1999/5/EK irányelv rendelkezéseit.
Íslenska
[Icelandic]
Hér, UBIQUITI NETWORKS, því yfir að þetta UBIQUITI NETWORKS
tæki er í samræmi við grunnkröfur og önnur viðeigandi ákvæði
tilskipun 1999/5/EC.
Italiano
[Italian]
Con la presente, UBIQUITI NETWORKS, dichiara che questo
dispositivo UBIQUITI NETWORKS, è conforme ai requisiti essenziali
ed alle altre disposizioni pertinenti della direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo, UBIQUITI NETWORKS, deklarē, ka UBIQUITI NETWORKS
ierīce, ir saskaņā ar būtiskajām prasībām un citiem attiecīgiem
noteikumiem Direktīvā 1999/5/EK.
Lietuviškai
[Lithuanian]
UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKS
įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB
Direktyvos nuostatas.
Malti
[Maltese]
Hawnhekk, UBIQUITI NETWORKS, tiddikjara li dan il-mezz
UBIQUITI NETWORKS huwa konformi mar-rekwiżiti essenzjali u
dispożizzjonijiet rilevanti oħrajn ta ‘Direttiva 1999/5/EC.
Norsk
[Norwegian]
Herved UBIQUITI NETWORKS, erklærer at denne UBIQUITI
NETWORKS enheten, er i samsvar med de grunnleggende kravene
og andre relevante bestemmelser i direktiv
1999/5/EF.
Slovensky
[Slovak]
Týmto
UBIQUITI NETWORKS
, prehlasuje, že toto
UBIQUITI
NETWORKS
zariadenie, je v súlade so základnými požiadavkami a
ďalšími relevantnými ustanoveniami smernice 1999/5/ES.
Svenska
[Swedish]
Härmed UBIQUITI NETWORKS, intygar att denna UBIQUITI
NETWORKS enhet är i överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser som framgår av
direktiv 1999/5/EG.
Español
[Spanish]
Por medio de la presente UBIQUITI NETWORKS declara que este
dispositivo UBIQUITI NETWORKS, cumple con los requisitos
esenciales y cualesquiera otras disposiciones aplicables o exigibles
de la Directiva 1999/5/CE.
Polski
[Polish]
Niniejszym, Ubiquiti Networks, oświadcza, że urządzenie UBIQUITI
NETWORKS, jest zgodny z zasadniczymi wymaganiami oraz
pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português
[Portuguese]
UBIQUITI NETWORKS declara que este dispositivo UBIQUITI
NETWORKS, está conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.
Română
[Romanian]
Prin prezenta, UBIQUITI NETWORKS declară că acest dispozitiv
UBIQUITI NETWORKS este în conformitate cu cerințele esențiale și
alte prevederi relevante ale Directivei 1999/5/CE.
Online Resources
Support support.ubnt.com
Community community.ubnt.com
Downloads downloads.ubnt.com
©2016 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti
Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airFiber, airOS, Rocket,
RocketDish, and TOUGHCable are trademarks or registered trademarks of
Ubiquiti Networks, Inc. in the United States and in other countries. All other
trademarks are the property of their respective owners. PH012816
www.ubnt.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Ubiquiti AF-MPx4 Guida Rapida
- Tipo
- Guida Rapida
- Questo manuale è adatto anche per
in altre lingue
Documenti correlati
-
Ubiquiti AF-5G23-S45 Guida Rapida
-
Ubiquiti airFiber AF-5X Manuale utente
-
-
-
-
-
-
Ubiquiti Edge Point EP-R8 Guida Rapida
-
-