TRADEMARK
All products and company names are trademarks or registered
trademarks of their respective holders.
These specifications are subjected to change without notice.
Manual Revision 1.0
Feb. 16 , 2000
BX6
A PA P
A PA P
A P
entiumentium
entiumentium
entium
®®
®®
®
II/III/Celer II/III/Celer
II/III/Celer II/III/Celer
II/III/Celer
onon
onon
on
Slot1 Processor based AGPSlot1 Processor based AGP
Slot1 Processor based AGPSlot1 Processor based AGP
Slot1 Processor based AGP
motherboard
FeaturesBX6
Page 2
FEATURES
BX6 Features:
•BX6 is based on the Pentium
®
II or Pentium
®
III Processor operating
at 233 ~ 400MHz (66MHz) or 300 ~ 600MHz (100MHz) on Slot 1.
There are no jumper setting for CPU Speed Setup but detected automati-
cally through the BIOS.
• Designed with Intel’s 82443 BX AGPset.
• Supports up to 768MB of SDRAM (minimum of 8 MB) on board, You can
use 168-pin DIMM x 3. It will automatically detect Extended Data Output
(EDO) DRAM at 66MHz only or Synchronous DRAM memory (SDRAM)
at 66MHz or 100MHz.
•BX6 will not support Error Checking and Correcting (ECC) when using
parity DRAM memory modules.
• Supports (1) 16 bit ISA slots, (6) 32 bit PCI slots, (1) AGP slot and provides
(2) independent high performance PCI IDE interfaces capable of supporting
PIO Mode 3/4 and Ultra DMA 33 devices. The BX6 supports (6) PCI
Bus Master slots and a jumperless PCI INT# control scheme which reduces
configuration confusion when plugging in PCI card(s).
• Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary
IDE interfaces.
• Designed with Winbond W83977TF/EF Multi I/O: (1) floppy port, (1)
parallel port (EPP, ECP), and (2) serial ports (16550 Fast UART).
Note: Japanese “Floppy 3 mode” is also supported.
• Includes a PS/2 mouse connector.
• Allows use of a PS/2 keyboard.
• Features Award Plug & Play BIOS. With Flash Memory you can always
upgrade to the current BIOS as they are released. (http://www.2themax.com
please visit our Technical Support section for the latest updates).
FeaturesBX6
Page 3
•BX6 utilizes a Lithium battery which provides environmental protec-
tion and longer battery life.
• Supports the Universal Serial Bus (USB) connector. The onboard PIIX4E
chip provides the means for connecting PC peripherals such as; keyboards,
joysticks, telephones, and modems.
• Built-in ATX 20-pin power supply connector.
• Software power-down when using Windows
®
95/98.
• Supports ring-in feature (remote power-on through external modem,
allow system to be turned on remotely).
• Resume by Alarm - Allow your system to turn on at a preselected time.
•
Power Loss Recovery - In the event of a power outage your system will
automatically turn itself back on without user intervention.
• Supports CPU Hardware sleep and SMM (System Management Mode).
• Supports Desktop Management Interface (DMI) facilitating the manage-
ment of desktop computers, hardware and software components and
peripherals, whether they are stand-alone systems or linked into networks.
(optional)
• Supports Hot key, Any key or password Keyboard power ON function
(KBPO).
• Supports USDM software to allow the status monitoring of various aspects
of the system when using Windows
®
95/98 or Windows
®
NT 4.0.
• Supports the CPU, PWR and Chassis fan Auto stop in the sleep mode.
• Supports the onboard standby in suspend green or STR mode LED (D2).
• Supports the STR (Suspend To RAM) power management by ACPI’s S3.
•Supports the STR indicator red LED (D8) to avoid plugging or un-plugging
DIMM modules when in a STR mode.
• Supports the System Power LED (PANEL) blinks in the sleep mode.
• Built-in WOL (Wake On Lan) Connector.
InstallationBX6
Page 4
Figure 1
BX6 Detailed Layout
Installation
BX6
Page 5
Easy Installation Procedure
Easy Installation Procedure
The following must be completed before powering on your new system:
Configure Jumpers
System memory Configuration
Device Connectors
Configure Settings
The following will describe all of the setting that you are required to set before
moving on to step 2.
ROM PCI/ISA BIOS(2A69KPAI)
SENSOR & CPU SPEED SETTING
AWARD SOFTWARE, INC.
Auto Detect DIMM/PCI Clk : Enabled
Spread Spectrum Modulated : Disabled
CPU Host Clock : Default
CPU/PCI Clk Ratio : Auto
CPU/AGP Clk Ratio : Auto
CPU Int Clk Ratio : x3
CPU Clk Frequency : 300(100x3) MHz
CPU:AGP (Clk:Clk) : 3:2 (100:66)
CPU:PCI (Clk:Clk) : 3:1 (100:33)
CPU Vio Voltage : 3.40V
CPU Vcore Voltage : +0.10V
CPU Vcore Voltage : 2.10V
CPU Warning Temperature : 95
O
C/205
O
C
Extended JP2 Temperature : 0
O
C/32
O
C
Current CPU Temperature : 0
O
C/32
O
C
Current System Temperature : 0
O
C/32
O
C
Current POWER FAN Speed :4900 RPM
Current CPU FAN Speed :4900 RPM
Current CHASSIS FAN Speed : 4900 RPM
Vcore : 2.10V Vtt(V) : 1.55V
Vio(V) : 3.47V +5V :5.02V
+12V : 12.40V -12V : -11.95V
-5V : -5.50V VBAT (V) : 3.44V
5VSB (V) : 5.08V
Shutdown Temperature : 100
O
C/167
O
C
Esc:Quit : Select Item
F1 : Help PU/PD/+/-: Modify
F5 : Old Values (Shift) F2 : Color
F7 : Load Setup Defaults
éé
éé
é
êê
êê
ê
èè
èè
è
çç
çç
ç
InstallationBX6
Page 6
Note:Based on the implementation of the Intel 440BX AGPset, the BX6
is able to provide multiple front side bus (FSB) frequencies for Slot 1
processors and memory operations. The motherboard's FSB is easily se-
lected by BIOS Setup listed above to match the FSB required by your
processor. When using the 100MHz FSB (or higher) you must use
PC100 (or better) compliant SDRAM.
Memory is an important component of any motherboard. When
selecting memory for use on the 2themax brand motherboard we
recommend use only the finest quality modules. 2themax would like to
stress that using non-compliant PC100 SDRAM modules with a
100MHz (or higher) FSB severely compromises the integrity of the
system.
epyTUPCkcolClanretxEoitaR
epyT1tolS
IImuitneP
IIImuitneP
noreleC
draCtrevnoC+073S
66
ro
001
0.2
5.2
0.3
5.3
0.4
5.4
0.5
5.5
0.6
5.6
0.7
5.7
0.8
JP1 = 1-2 - Normal (Default)
= 2-3 - Clear CMOS (momentarily)
JP2 CMOS Clear
1
JP1 = 1-2 - Normal (Default)
= 2-3 - Clear CMOS (momentarily)
JP1 Chassis (Case) intruder detect
1
JP4 Keyboard Power-ON function
JP4 = 1-2 - Enabled
= 2-3 - Disabled (Default)
1
Installation
BX6
Page 7
J7
Reserved for NIC (Network Interface Card) to
Wake the System.
WOL (Wake On Lan) Connector
J1 SB-LINK Connector
Reserved for Creative SB-LINK (Sound
Blaster LINK ) with the Sound Blaster
AWE64D PCI Sound Card to compatible
TM
TM
= 1-2 - Sixth Slave (Default)
= 2-3 - Sixth Master
JPX1&JPX2 The Fifth or Sixth PCI Master Select
1
1
JPX1
&
JPX2
LED1
LED2
Debug card on board
(Please refer to Appendix B for POST codes)
InstallationBX6
Page 8
yromeMlatoT
1MMID
)1/0knaB(
2MMID
)3/2knaB(
3MMID
)5/4knaB(
BM652=
mumixaM
*MARDS/ODE
,BM23,BM61,BM8
,BM821,BM46
1xBM652
enoNenoN
BM215=
mumixaM
*MARDS/ODE
,BM23,BM61,BM8
,BM821,BM46
1xBM652
*MARDS/ODE
,BM23,BM61,BM8
,BM821,BM46
1xBM652
enoN
BM867=
mumixaM
*MARDS/ODE
,BM23,BM61,BM8
,BM821,BM46
1xBM652
*MARDS/ODE
,BM23,BM61,BM8
,BM821,BM46
1xBM652
*MARDS/ODE
,BM23,BM61,BM8
,BM821,BM46
1xBM652
* SDRAM only supports 8, 16, 32, 64, 128MB DIMM modules.
*
Using non-compliant memory with higher bus speed (over clocking)
may severely compromise the integrity of the system.
System Memory Configuration
Memory Layout
The BX6 supports (3) 168-pin DIMMs (Dual In-line Memory Module). The
DIMMs can be either EDO (Extended Data Out) or SDRAM (Synchronized
DRAM).
• We recommend not mixing SDRAM DIMM and EDO DIMM together.
• EDO DIMM can only be used with the 66MHz FSB.
• We recommend using at least 125MHz (-8ns) SDRAM DIMM at the 100MHz
(or higher) FSB as timing becomes more critical at these higher speeds.
• DIMM SDRAM may be 83MHz (-12ns), 100MHz (-10ns) or 125MHz
(-8ns) bus speed.
Figure 2 and Table 1 show several possible memory configurations using
Figure 2
Table 1
DIMM 1 (M1)
DIMM 2 (M2)
DIMM 3 (M3)
Bank 0/1
Bank 2/3
Bank 4/5
-Synchronous
-SDRAM or EDO
DIMM
InstallationBX6
Page 9
Device Connectors
Please install the motherboard into the chassis.
Now that your motherboard is installed you are ready to connect all your connec-
tions (figure 7).
Figure 7
PS/2 Mouse
PS/2 Keyboard
Parallel Port
COM1USB
COM2
J2,J3: Chassis Panel Connector
• Power LED, Speaker, Reset, Turbo LED, HDD LED, IR Conn., Sleep/
Power_ON
J4: CPU Fan Power
• A plug-in for the CPU Fan Power
J6: Power Supply Fan Monitoring
• A plug-in for the Power supply so that BIOS can monitor the RPM’s
J8: Chassis Fan Power
• A plug-in for the chassis Fan Power
IDE1: Primary IDE Connector
IDE2: Secondary IDE Connector
FDD1: Floppy Controller Connector
PW1: ATX Power Connector
• 20-pin power connector
Installation
BX6
Page 10
Device Connectors (continued)
(This is connected to the power button on the case. Using the Soft-
Off by Pwr-BTTN feature, you can choose either Instant Off (turns
system off immediately), or 4 sec delay (you need to hold the button
down for 4 seconds before the system turns off). When the system is
in 4 sec delay mode, there is a special feature to make the system to
go into suspend mode when the button is pressed momentarily.)
Turbo LED indicator - LED ON when higher speed is selected
IDE LED indicator - LED ON when Onboard PCI IDE Hard disks
is activate
J3
1
+
+
IR Connector
1. VCC 4. GND
2. NC 5. IRTX
3. IRRX
1
Power On/Off
J2
Speaker -
Connect to the system's speaker for beeping
1. Speaker 3. GND
2. N/C 4. GND
Reset - Closed to restart system.
KeyLock - Keyboard lock switch & Power LED connector
1. Power LED(+) 4. KeyLock
2. N/C 5. GND
3. GND
1
1
1
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
EPOX BX6 Instructions Manual
- Tipo
- Instructions Manual
- Questo manuale è adatto anche per
in altre lingue
- English: EPOX BX6