ASROCK P45X3 DELUXE Manuale del proprietario

11

1

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or trans-

lated in any language, in any form or by any means, except duplication of documen-

tation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identifica-

tion or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or omissions

that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any kind,

either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose. In no event shall

ASRock, its directors, officers, employees, or agents be liable for any indirect, special,

incidental, or consequential damages (including damages for loss of profits, loss of

business, loss of data, interruption of business and the like), even if ASRock has been

advised of the possibility of such damages arising from any defect or error in the guide

or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic

substance controlled in Perchlorate Best Management Practices (BMP) regulations

passed by the California Legislature. When you discard the Lithium battery in

California, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see

www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

Published May 2009

22

2

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

Motherboard LayoutMotherboard Layout

Motherboard Layout

1 PS2_USB_PWR1 Jumper 21 South Bridge Controller

2 ATX 12V Connector (ATX12V1) 22 USB 2.0 Header (USB8_9, Blue)

3 775-Pin CPU Socket 23 Debug LED

4 North Bridge Controller 24 System Panel Header (PANEL1, Orange)

5 CPU Fan Connector (CPU_FAN1) 25 Chassis Speaker Header (SPEAKER 1, Purple)

6 2 x 240-pin DDR3 DIMM Slots 26 TPM Header (TPM1)

(Dual Channel A: DDR3_A1, DDR3_B1; Blue) 27 Floppy Connector (FLOPPY1)

7 2 x 240-pin DDR3 DIMM Slots 28 COM Port Header (COM1)

(Dual Channel B: DDR3_A2, DDR3_B2; White) 29 Front Panel Audio Header

8 ATX Power Connector (ATXPWR1) (HD_AUDIO1, Lime)

9 IDE1 Connector (IDE1, Blue) 30 HDMI_SPDIF Header (HDMI_SPDIF1, Yellow)

10 Front Panel IEEE 1394 Header 31 Internal Audio Connector: CD1 (Black)

(FRONT_1394; Red) 32 PCI Slots (PCI1- 2)

11 Fourth SATAII Connector (SATAII_4; Red) 33 PCI Express x16 Slot (PCIE5; Orange)

12 Secondary SATAII Connector (SATAII_2; Red) 34 Infrared Module Header (IR1)

13 Chassis Fan Connector (CHA_FAN1) 35 PCI Express x1 Slot (PCIE4)

14 Primary SATAII Connector (SATAII_1; Red) 36 SLI/XFire Switch Card Retention Slot

15 Third SATAII Connector (SATAII_3; Red) 37 PCI Express x1 Slot (PCIE3)

16 Fifth SATAII Connector (SATAII_5; Red) 38 PCI Express x16 Slot (PCIE2; Blue)

17 Sixth SATAII Connector (SATAII_6; Red) 39 PCI Express x1 Slot (PCIE1)

18 Reset Switch (RSTBTN) 40 Clear CMOS Jumper (CLRCMOS1)

19 Power Switch (PWRBTN) 41 Power Fan Connector (PWR_FAN1)

20 USB 2.0 Header (USB10_11, Blue) 42 NB Fan Connector (NB_FAN1)

33

3

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

I/O PI/O P

I/O P

anelanel

anel

To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. After restarting your computer, you will find “Mixer” tool on your system.

Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click

“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA

Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek

HDA Audio 2nd output” to use front panel audio.

** If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.

See the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker

(No. 10) (No. 7) (No. 8) (No. 6)

2 V -- -- --

4VV----

6 VVV--

8 VVVV

1 PS/2 Mouse Port (Green) ** 10 Front Speaker (Lime)

2 Coaxial SPDIF Out Port 11 Microphone (Pink)

3 USB 2.0 Port (USB0) 12 USB 2.0 Ports (USB67)

4 IEEE 1394 Port (IEEE 1394) 13 USB 2.0 Ports (USB45)

* 5 LAN RJ-45 Port 14 USB 2.0 Ports (USB23)

6 Side Speaker (Gray) 15 Powered eSATAII/USB Connector

7 Rear Speaker (Black) 16 Optical SPDIF Out Port

8 Central / Bass (Orange) 17 Clear CMOS Switch (CLRCBTN)

9 Line In (Light Blue) 18 PS/2 Keyboard Port (Purple)

LAN Port

ACT/LINK

LED

SPEED

LED

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED

indications.

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description

Off No Activity Off 10Mbps connection

Blinking Data Activity Orange 100Mbps connection

Green 1Gbps connection

44

4

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

1. Introduction1. Introduction

1. Introduction

Thank you for purchasing ASRock P45X3 Deluxe motherboard, a reliable motherboard

produced under ASRock’s consistently stringent quality control. It delivers excellent

performance with robust design conforming to ASRock’s commitment to quality and

endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-step

installation guide. More detailed information of the motherboard can be found in the user

manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might be

updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock website

as well. ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit

our website for specific information about the model you are using.

www.asrock.com/support/index.asp

1.1 Package Contents1.1 Package Contents

1.1 Package Contents

ASRock P45X3 Deluxe Motherboard

(ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm)

ASRock P45X3 Deluxe Quick Installation Guide

ASRock P45X3 Deluxe Support CD

One ASRock SLI/XFire Switch Card

One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable

One Ribbon Cable for a 3.5-in Floppy Drive

Four Serial ATA (SATA) Data Cables (Optional)

One Serial ATA (SATA) HDD Power Cable (Optional)

One I/O Panel Shield

55

5

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform - ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm

- All Solid Capacitor design (100% Japan-made high-quality

Conductive Polymer Capacitors)

CPU - LGA 775 for Intel

®

Core

TM

2 Extreme / Core

TM

2 Quad / Core

TM

2 Duo / Pentium

®

Dual Core / Celeron

®

Dual Core / Celeron

®

,

supporting Penryn Quad Core Yorkfield and Dual Core

Wolfdale processors

- Compatible with FSB2000/1600/1333/1066/800 MHz

(see CAUTION 1)

- Advanced V8 Power Phase Design

- Supports Hyper-Threading Technology (see CAUTION 2)

- Supports Untied Overclocking Technology (see CAUTION 3)

- Supports EM64T CPU

Chipset - Northbridge: Intel

®

P45

- Southbridge: Intel

®

ICH10

Memory - Dual Channel DDR3 Memory Technology (see CAUTION 4)

- 4 x DDR3 DIMM slots

- Support DDR3 1600/1333/1066/800 non-ECC, un-buffered

memory (see CAUTION 5)

- Max. capacity of system memory: 16GB (see CAUTION 6)

Expansion Slot - 2 x PCI Express 2.0 x16 slots

(blue @ x16 mode, orange @ x8 mode)

- 3 x PCI Express x1 slots

- 2 x PCI slots

- Supports ATI

TM

CrossFireX

TM

(see CAUTION 7)

Audio - 7.1 CH Windows

®

Vista

TM

Premium Level HD Audio

(ALC888 Audio Codec)

LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111DL

- Supports Wake-On-LAN

Rear Panel I/O I/O Panel

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Coaxial SPDIF Out Port

- 1 x Optical SPDIF Out Port

- 1 x IEEE 1394 Port

- 7 x Ready-to-Use USB 2.0 Ports

- 1 x Powered eSATAII/USB Connector

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)

66

6

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

- 1 x Clear CMOS Switch with LED

- HD Audio Jack: Side Speaker/Rear Speaker/Central/Bass/

Line in/Front Speaker/Microphone (see CAUTION 8)

Connector - 6 x SATAII 3.0Gb/s connectors, support NCQ, AHCI and “Hot

Plug” functions (see CAUTION 9)

- 1 x ATA133 IDE connector (supports 2 x IDE devices)

- 1 x Floppy connector

- 1 x IR header

- 1 x COM port header

- 1 x HDMI_SPDIF header

- 1 x IEEE 1394 header

- 1 x TPM header

- CPU/Chassis/NB/Power FAN connector

- 24 pin ATX power connector

- 8 pin 12V power connector

- CD in header

- Front panel audio connector

- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

(see CAUTION 10)

Quick Switch - 1 x Clear CMOS Switch with LED

- 1 x Power Switch with LED

- 1 x Reset Switch with LED

BIOS Feature - 8Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- AMBIOS 2.3.1 Support

- CPU, VCCM, VTT Voltage Multi-adjustment

- Supports I. O. T. (Intelligent Overclocking Technology)

- Supports Smart BIOS

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version)

Unique Feature - ASRock OC Tuner (see CAUTION 11)

- Intelligent Energy Saver (see CAUTION 12)

- Instant Boot

- ASRock Instant Flash (see CAUTION 13)

- Hybrid Booster:

- CPU Frequency Stepless Control (see CAUTION 14)

- ASRock U-COP (see CAUTION 15)

- Boot Failure Guard (B.F.G.)

Hardware - CPU Temperature Sensing

Monitor - Chassis Temperature Sensing

77

7

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

WARNING

Please realize that there is a certain risk involved with overclocking, including adjusting

the setting in the BIOS, applying Untied Overclocking Technology, or using the third-

party overclocking tools. Overclocking may affect your system stability, or even

cause damage to the components and devices of your system. It should be done at

your own risk and expense. We are not responsible for possible damage caused by

overclocking.

CAUTION!

1. Some CPU you adopt may be overclocked to FSB2000 MHz, in this

situation, please adopt DDR3 1333 or DDR3 1600 memory modules on

this motherboard.

2. About the setting of “Hyper Threading Technology”, please check page 49

of “User Manual” in the support CD.

3. This motherboard supports Untied Overclocking Technology. Please read

“Untied Overclocking Technology” on page 32 for details.

4. This motherboard supports Dual Channel Memory Technology. Before you

implement Dual Channel Memory Technology, make sure to read the

installation guide of memory modules on page 12 for proper installation.

5. Please check the table below for the CPU FSB frequency and its

corresponding memory support frequency.

CPU FSB Frequency Memory Support Frequency

1600 DDR3 800, DDR3 1066, DDR3 1333,

DDR3 1600

1333 DDR3 800, DDR3 1066, DDR3 1333

1066 DDR3 800, DDR3 1066

800 DDR3 800

* DDR3 1600 memory module is operating in overclocking mode.

6. Due to the operating system limitation, the actual memory size may be

less than 4GB for the reservation for system usage under Windows

®

XP

and Windows

®

Vista

TM

. For Windows

®

XP 64-bit and Windows

®

Vista

TM

64-

bit with 64-bit CPU, there is no such limitation.

7. This motherboard supports ATI

TM

CrossFireX

TM

technology. If you want to use

CrossFireX

TM

function, please follow the instructions on page 17 to reverse the

direction of ASRock SLI/XFire Switch Card in advance.

- CPU/Chassis/NB/Power Fan Tachometer

- CPU Quiet Fan

- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore

OS - Microsoft

®

Windows

®

2000 / XP / XP 64-bit / Vista

TM

/

Vista

TM

64-bit compliant (see CAUTION 16)

Certifications - FCC, CE, WHQL

* For detailed product information, please visit our website: http://www.asrock.com

88

8

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

8. For microphone input, this motherboard supports both stereo and mono

modes. For audio output, this motherboard supports 2-channel, 4-channel,

6-channel, and 8-channel modes. Please check the table on page 3 for

proper connection.

9. Before installing SATAII hard disk to SATAII connector, please read the

“SATAII Hard Disk Setup Guide” on page 37 of “User Manual” in the support

CD to adjust your SATAII hard disk drive to SATAII mode. You can also

connect SATA hard disk to SATAII connector directly.

10. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

Vista

TM

64-bit / Vista

TM

/ XP 64-bit / XP SP1 or SP2 / 2000 SP4.

11. It is a user-friendly ASRock overclocking tool which allows you to surveil

your system by hardware monitor function and overclock your hardware

devices to get the best system performance under Windows

®

environment.

Please visit our website for the operation procedures of ASRock OC

Tuner. ASRock website: http://www.asrock.com

12. Featuring an advanced proprietary hardware and software design,

Intelligent Energy Saver is a revolutionary technology that delivers

unparalleled power savings. In other words, it is able to provide exceptional

power saving and improve power efficiency without sacrificing computing

performance. Please visit our website for the operation procedures of

Intelligent Energy Saver.

ASRock website: http://www.asrock.com

13. ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM.

This convenient BIOS update tool allows you to update system BIOS

without entering operating systems first like MS-DOS or Windows

®

. With

this utility, you can press <F6> key during the POST or press <F2> key to

BIOS setup menu to access ASRock Instant Flash. Just launch this tool

and save the new BIOS file to your USB flash drive, floppy disk or hard

drive, then you can update your BIOS only in a few clicks without prepar-

ing an additional floppy diskette or other complicated flash utility. Please

be noted that the USB flash drive or hard drive must use FAT32/16/12 file

system.

14. Although this motherboard offers stepless control, it is not recommended

to perform over-clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU.

15. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC system.

16. AHCI function is not supported under Windows

®

2000 OS. It is recom-

mended to use IDE mode under Windows

®

2000. Please refer to page 59 of

“User Manual” in the support CD for detailed setup.

99

9

ASRock P45X3 Deluxe Motherboard

2.2.

2.

InstallationInstallation

Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet

or the like. Also remember to use a grounded wrist strap or touch

a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded

antstatic pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the

motherboard to the chassis, please do not over-tighten the

screws! Doing so may damage the motherboard.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

For the installation of Intel 775-LAND CPU,

please follow the steps below.

Before you insert the 775-LAND CPU into the socket, please check if

the CPU surface is unclean or if there is any bent pin on the socket.

Do not force to insert the CPU into the socket if above situation is

found. Otherwise, the CPU will be seriously damaged.

775-Pin Socket Overview

EnglishEnglish

English

1010

10

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing

down and out on the hook to clear

retention tab.

Step 1-2. Rotate the load lever to fully open po-

sition at approximately 135 degrees.

Step 1-3. Rotate the load plate to fully open po-

sition at approximately 100 degrees.

Step 2. Insert the 775-LAND CPU:

Step 2-1. Hold the CPU by the edges where are

marked with black lines.

Step 2-2. Orient the CPU with IHS (Integrated

Heat Sink) up. Locate Pin1 and the two

orientation key notches.

For proper inserting, please ensure to match the two orientation key

notches of the CPU with the two alignment keys of the socket.

Step 2-3. Carefully place the CPU into the socket

by using a purely vertical motion.

Step 2-4. Verify that the CPU is within the socket

and properly mated to the orient keys.

Step 3. Remove PnP Cap (Pick and Place Cap):

Use your left hand index finger and thumb to

support the load plate edge, engage PnP cap

with right hand thumb and peel the cap from the

socket while pressing on center of PnP cap to

assist in removal.

black line

775-Pin Socket

Pin1

alignment key

Pin1

orientation

key notch

orientation

key notch

775-LAND CPU

1111

11

ASRock P45X3 Deluxe Motherboard

1. It is recommended to use the cap tab to handle and avoid kicking

off the PnP cap.

2. This cap must be placed if returning the motherboard for after

service.

Step 4. Close the socket:

Step 4-1. Rotate the load plate onto the IHS.

Step 4-2. While pressing down lightly on load

plate, engage the load lever.

Step 4-3. Secure load lever with load plate tab

under retention tab of load lever.

2.22.2

2.2

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

Installation of CPU Fan and Heatsink

For proper installation, please kindly refer to the instruction manuals of your CPU fan

and heatsink.

Below is an example to illustrate the installation of the heatsink for 775-LAND CPU.

Step 1. Apply thermal interface material onto center

of IHS on the socket surface.

Step 2. Place the heatsink onto the socket. Ensure

fan cables are oriented on side closest to the

CPU fan connector on the motherboard

(CPU_FAN1, see page 2, No. 5).

Step 3. Align fasteners with the motherboard

throughholes.

Step 4. Rotate the fastener clockwise, then press

down on fastener caps with thumb to install

and lock. Repeat with remaining fasteners.

If you press down the fasteners without rotating them clockwise,

the heatsink cannot be secured on the motherboard.

Step 5. Connect fan header with the CPU fan

connector on the motherboard.

Step 6. Secure excess cable with tie-wrap to ensure

cable does not interfere with fan operation or

contact other components.

EnglishEnglish

English

1212

12

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

2.3 Installation of Memory Modules (DIMM)2.3 Installation of Memory Modules (DIMM)

2.3 Installation of Memory Modules (DIMM)

This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots,

and supports Dual Channel Memory Technology. For dual channel configuration,

you always need to install identical (the same brand, speed, size and chip-

type) DDR3 DIMM pair in the slots of the same color. In other words, you have to

install identical DDR3 DIMM pair in Dual Channel A (DDR3_A1 and DDR3_B1;

Blue slots; see p.2 No.6) or identical DDR3 DIMM pair in Dual Channel B

(DDR3_A2 and DDR3_B2; white slots; see p.2 No.7), so that Dual Channel

Memory Technology can be activated. This motherboard also allows you to

install four DDR3 DIMMs for dual channel configuration, and please install iden-

tical DDR3 DIMMs in all four slots. You may refer to the Dual Channel Memory

Configuration Table below.

Dual Channel Memory Configurations

DDR3_A1 DDR3_A2 DDR3_B1 DDR3_B2

(Blue Slot) (White Slot) (Blue Slot) (White Slot)

(1) Populated - Populated -

(2) - Populated - Populated

(3)* Populated Populated Populated Populated

* For the configuration (3), please install identical DDR3 DIMMs in all four

slots.

1. If you want to install two memory modules, for optimal compatibility

and reliability, it is recommended to install them in the slots of the

same color. In other words, install them either in the set of blue slots

(DDR3_A1 and DDR3_B1), or in the set of white slots (DDR3_A2

and DDR3_B2).

2. If only one memory module or three memory modules are installed

in the DDR3 DIMM slots on this motherboard, it is unable to activate

the Dual Channel Memory Technology.

3. If a pair of memory modules is NOT installed in the same Dual

Channel, for example, installing a pair of memory modules in

DDR3_A1 and DDR3_A2, it is unable to activate the Dual Channel

Memory Technology .

4. It is not allowed to install a DDR or DDR2 memory module into

DDR3 slot;otherwise, this motherboard and DIMM may be damaged.

5. If you adopt a DDR3 1600 memory module, you can only install it on

DDR3_A1 slot.

1313

13

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the slot

at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

1414

14

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

2.4 Expansion Slots (PCI and PCI Express Slots)2.4 Expansion Slots (PCI and PCI Express Slots)

2.4 Expansion Slots (PCI and PCI Express Slots)

There are 2 PCI slots and 5 PCI Express slots on this motherboard.

PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

PCIE Slots:

PCIE1 / PCIE3 / PCIE4 (PCIE x1 slot; White) is used for PCI Express

cards with x1 lane width cards, such as Gigabit LAN card, SATA2

card, etc.

PCIE2 (PCIE x16 slot; Blue) is used for PCI Express x16 lane width

graphics cards, or used to install PCI Express graphics cards to

support CrossFireX

TM

function.

PCIE5 (PCIE x16 slot; Orange) is used for PCI Express x1 lane width

cards, such as Gigabit LAN card, SATA2 card, etc., or used to install

PCI Express graphics cards to support CrossFireX

TM

function.

PCIE2 / PCIE5 / SLI/XFire Switch Card Retention Slot

Configurations

PCIE2 Slot PCIE5 Slot SLI/XFire Switch Card

(Blue) (Orange) Retention Slot

Single Graphics Card PCIE x16 N/A

Dual Graphics Cards PCIE x8 PCIE x8

in CrossFireX

TM

Mode

(Default)

1515

15

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

1. If you plan to install only one PCI Express VGA card on this

motherboard, please install it on PCIE2 slot (Blue). In this mode,

you do not need to adjust the default setting of ASRock SLI/XFire

Switch Card, and please do not remove or lose ASRock SLI/XFire

Switch Card when it is still in working condition.

2. For the information of the compatible CrossFireX

TM

Mode PCI

Express VGA cards and CrossFireX

TM

setup procedures, please refer

to “CrossFireX

TM

Operation Guide” on page 16.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed in

a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screws for later use.

Step 4. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

1616

16

ASRock P45X3 Deluxe Motherboard

2.5 CrossFireX2.5 CrossFireX

2.5 CrossFireX

TMTM

TM

Operation Guide Operation Guide

Operation Guide

This motherboard supports CrossFireX

TM

feature. CrossFireX

TM

technology offers

the most advantageous means available of combining multiple high performance

Graphics Processing Units (GPU) in a single PC. Combining a range of different

operating modes with intelligent software design and an innovative interconnect

mechanism, CrossFireX

TM

enables the highest possible level of performance and

image quality in any 3D application. Currently CrossFireX

TM

feature is supported with

Windows

®

XP with Service Pack 2 and Vista

TM

OS. Please check AMD website for

ATI

TM

CrossFireX

TM

driver updates.

EnglishEnglish

English

1. If a customer incorrectly configures their system they will not see the

performance benefits of CrossFireX

TM

. All three CrossFireX

TM

components, a

CrossFireX

TM

Ready graphics card, a CrossFireX

TM

Ready motherboard and a

CrossFireX

TM

Edition co-processor graphics card, must be installed correctly to

benefit from the CrossFireX

TM

multi-GPU platform.

2. If you pair a 12-pipe CrossFireX

TM

Edition card with a 16-pipe card, both cards will

operate as 12-pipe cards while in CrossFireX

TM

mode.

What graphics cards work with CrossFireX

TM

?

A complete CrossFireX

TM

system requires a CrossFireX

TM

Ready motherboard, a

CrossFireX

TM

Edition graphics card and a compatible standard Radeon (CrossFireX

TM

Ready) graphics card from the same series, or two CrossFireX

TM

Ready cards. This

applies to cards from ATI

TM

or any of its partners. Please refer to below table for

CrossFireX

TM

VGA card support list according to the OS you install.

For Windows

®

XP

Vendor Chipset Model Driver

ATI Radeon HD 2600PRO MSI RX2600PRO-T2D256EZ Catalyst 9.1

Radeon HD 2600XT Gigabyte GV-RX26T256HP-B Catalyst 9.1

RADEON 3650 Powercolor AX3650 512MMD3-XP Catalyst 9.1

RADEON 3850 Gigabyte GV-RX385256H-B Catalyst 9.1

RADEON 3870 Powercolor AX3870 512MD4-H Catalyst 9.1

Radeon HD 4350 ASUS EAH4350 SILENT/DI/512MD2/A Catalyst 9.1

RADEON 4670 Powercolor AX4670 512MD3-P Catalyst 9.1

RADEON 4850 Gecube GC-HD485PG3-E3 Catalyst 9.1

For Windows

®

Vista

Vendor Chipset Model Driver

ATI Radeon HD 2600PRO MSI RX2600PRO-T2D256EZ Catalyst 9.1

Radeon HD 2600XT Gigabyte GV-RX26T256HP-B Catalyst 9.1

RADEON 3650 Powercolor AX3650 512MMD3-XP Catalyst 9.1

RADEON 3850 Gigabyte GV-RX385256H-B Catalyst 9.1

RADEON 3870 Powercolor AX3870 512MD4-H Catalyst 9.1

RADEON 3870 Powercolor AX3870X2 1GBD3-H Catalyst 9.1

Radeon HD 4350 ASUS EAH4350 SILENT/DI/512MD2/A Catalyst 9.1

RADEON 4670 Powercolor AX4670 512MD3-P Catalyst 9.1

RADEON 4850 Gecube GC-HD485PG3-E3 Catalyst 9.1

Radeon HD 4870X2 ASUS EAH4870X2/HDTI/2G Catalyst 9.1

1717

17

ASRock P45X3 Deluxe Motherboard

Step 1. There is one ASRock SLI/XFire Switch Card factory-mounted on this

motherboard. This card served as a switch between the default mode

(x16) and CrossFireX

TM

mode (x8 / x8). ASRock SLI/XFire Switch Card is

factory-mounted with its default mode (x16) side toward the retention slot

base.

Step 2. To change it to CrossFireX

TM

Mode, you need to reverse the direction of

ASRock SLI/XFire Switch Card. Please simultaneously pull open both the

retention arms that hold the card in position. The card itself will spring

away from the retention slot. Take it out gently by holding its edges, and

keep away from touching the connectors (Golden Fingers).

Step 3. Reverse the card direction so as to have the “X8 / X8 MODE” wording side

toward the retention slot base. Insert the card into the bottom of the base.

Enjoy the benefit of CrossFireXEnjoy the benefit of CrossFireX

Enjoy the benefit of CrossFireX

TMTM

TM

Different CrossFireX

TM

cards may require different methods to enable CrossFireX

TM

feature. In below procedures, we use Radeon 4850 as the example graphics card. For

other CrossFireX

TM

cards that ATI

TM

has released or will release in the future, please

refer to ATI

TM

graphics card manuals for detailed installation guide.

EnglishEnglish

English

1818

18

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

Step 5. Install one Radeon graphics card to PCIE2 slot. For the proper installation

procedures, please refer to section “Expansion Slots”.

Step 6. Install one Radeon graphics card to PCIE5 slot. For the proper installation

procedures, please refer to section “Expansion Slots”.

Step 7. Connect two Radeon graphics cards by installing two CrossFire

TM

Bridge

on CrossFire

TM

Bridge Interconnects on the top of Radeon graphics cards.

(CrossFire

TM

Bridge is provided with the graphics card you purchase, not

bundled with this motherboard. Please refer to your graphics card vendor

for details.)

CrossFire

TM

Bridge

Step 4. Push the card down into the retention slot till both the retention arms firmly

hold the card into position. Also, keep away from touching the connectors

(Golden Fingers).

1919

19

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

Step 9. Power on your computer and boot into OS.

Step 10. Remove the ATI

TM

driver if you have any VGA driver installed in your system.

The Catalyst Uninstaller is an optional download. We recommend using this

utility to uninstall any previously installed Catalyst drivers prior to installation.

Please check AMD website for ATI

TM

driver updates.

Step 11. Install the required drivers to your system.

For Windows

®

XP OS:

A. ATI

TM

recommends Windows

®

XP Service Pack 2 or higher to be

installed (If you have Windows

®

XP Service Pack 2 or higher installed

in your system, there is no need to download it again):

http://www.microsoft.com/windowsxp/sp2/default.mspx

B. You must have Microsoft .NET Framework installed prior to

downloading and installing the CATALYST Control Center. Please

check Microsoft website for details.

For Windows

®

Vista

TM

OS:

Install the CATALYST Control Center. Please check AMD website for details.

Step 12. Restart your computer.

Step 13. Install the VGA card drivers to your system, and restart your computer.

Then you will find “ATI Catalyst Control Center” on your Windows

®

taskbar.

ATI Catalyst Control Center

Step 8. Connect the DVI monitor cable to the DVI connector on the Radeon graphics

card on PCIE2 slot. (You may use the DVI to D-Sub adapter to convert the

DVI connector to D-Sub interface, and then connect the D-Sub monitor

cable to the DVI to D-Sub adapter.)

2020

20

ASRock P45X3 Deluxe Motherboard

EnglishEnglish

English

Although you have selected the option “Enable CrossFire

TM

”, the CrossFireX

TM

function may not work actually. Your computer will automatically reboot. After

restarting your computer, please confirm whether the option “Enable CrossFire

TM

”

in “ATI Catalyst Control Center” is selected or not; if not, please select it again,

and then you are able to enjoy the benefit of CrossFireX

TM

feature.

Step 15. You can freely enjoy the benefit of CrossFireX

TM

feature.

* CrossFireX

TM

appearing here is a registered trademark of ATI

TM

Technologies Inc., and is used

only for identification or explanation and to the owners’ benefit, without intent to infringe.

* For further information of ATI

TM

CrossFireX

TM

technology, please check AMD website for

updates and details.

2.6 Surround Display Feature2.6 Surround Display Feature

2.6 Surround Display Feature

This motherboard supports Surround Display upgrade. With the external add-on

PCI Express VGA cards, you can easily enjoy the benefits of Surround Display

feature. For the detailed instruction, please refer to the document at the following

path in the Support CD:

..\ Surround Display Information

Step 14. Double-click “ATI Catalyst Control Center”. Click “View”, and select

“Advanced View”. Click “CrossFire

TM

”, and then set the option “Enable

CrossFire

TM

” to “Yes”.

View

CrossFire

TM

Enable CrossFire

TM

La pagina sta caricando ...

ASROCK P45X3 DELUXE Manuale del proprietario

ASROCK P45X3 DELUXE Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti