Candy CDC 168-SY Manuale utente

Categoria
Asciugatrici elettriche
Tipo
Manuale utente
User Instructions
Mode d’emploi
Instruções do utilizador
Brugervejledning
Bruksanvisning
Brukerveiledning
Käyttöohjeet
Gebruiksaanwijzingen
Istruzioni per l’uso
CDC 168
Reverse Action
EN
FR
PT
S
NO
SF
DA
NL
IT
40001717ENG.fm Page 1 Saturday, July 10, 2004 7:32 PM
2
2
2
1
3
3
4
7
6
5
40001717ENG.fm Page 2 Saturday, July 10, 2004 7:32 PM
12
1
2
3
4
5
9
10
11
8
40001717ENG.fm Page 3 Saturday, July 10, 2004 7:32 PM
ENGLISH
4
Safety Reminders
WARNING Check that the product has no
visible signs of damage before use. If damaged
do not use and please contact GIAS Service.
WARNING Do not use the product if the fluff
filter is not in position or is damaged; fluff
could be ignited.
WARNING Foam rubber materials can, under
certain circumstances, when heated become
ignited by spontaneous combustion. Foam
plastic, foam rubber and rubber-like material
are not suitable for tumble drying. Articles
made from these materials MUST NOT be
placed in the dryer.
Always refer to the laundry care labels for
directions on suitability for drying.
WARNING Misuse of a tumble dryer may
create a fire hazard.
WARNING Where the hot surface symbol
is located the temperature rise during operation
of the tumble dryer may be in excess of 60° C.
User’s manual. This machine should only be
used for its intended purpose as described in
this manual. Ensure that it is fully understood
before operating.
Installation. This machine should not be
installed in a bathroom or shower room.
Never install the dryer against curtains and be
sure to prevent items from falling or collecting
behind the dryer.
Ventilation. Adequate ventilation must be
provided in the room where the tumble dryer is
located to prevent gases from appliances burning
other fuels, including open fires, being drawn into
the room during operation of the tumble dryer.
Exhaust air must not be discharged into a flue
which is used for exhausting fumes from
appliances burning gas or other fuels.
Check regularly that the air flowing through the
dryer is not restricted
Check the fluff filter after use, and clean, if
necessary.
The venting hose or duct should be checked
periodically and any accumulation of fluff
removed.
The inlet and outlets should be kept free from
obstructions.
If the dryer is used frequently the period
between checks should be reduced accordingly.
Dryness. Clothes should be spin dried or
thoroughly wrung before they are put into the
tumble dryer. Clothes that are dripping wet
should NOT be put into the dryer.
Lighters and matches must not be left in
pockets and NEVER use flammable liquids
near the machine.
Glass fibre curtains should never be put in this
machine. Skin irritation may occur if other
garments are contaminated with the glass fibres.
Garments treated or contaminated with
flammable cleaning sprays or liquids such as
petrol, cooking oil or aerosol sprays must not be
put in this machine.
Lint or fluff must not be allowed to collect on
the floor around the outside of the machine.
Cool down period. The drum inside may be
very hot. Always allow the dryer to complete
the cool down period before removing the
laundry.
Faults. Do not continue to use this machine if it
appears to be faulty.
After use. Remove the plug from the electricity
supply. Always remove the plug before cleaning
the appliance.
Supply cord. If the supply cord on this
appliance is damaged, it must be replaced by a
special cord which is only available from GIAS
Service or an authorised dealer.
GIAS Service. To ensure the continued safe
and efficient operation of this appliance we
recommend that any servicing or repairs are
only carried out by an authorised service
engineer.
40001717ENG.fm Page 4 Saturday, July 10, 2004 7:32 PM
5
ENGLISH
Safety reminders 4 Filter 7
Electrical requirements 5 Water container 8
Installation requirements 6 Condenser 8
Preparing the load 6 Drying guide 9
Clothes preparation 6 Controls & indicators 10
Maximum drying weight 6 Operation 11
Sorting the load 6-7 Cleaning the dryer 12
Do not tumble dry 7 Technical specification 12
Energy saving 7 Trouble shooting 13
Opening the door 7
PLEASE READ THESE INSTRUCTIONS THOROUGHLY
This appliance must be operated in accordance with the instructions given in this manual.
It is for domestic use only in drying household textiles and garments where a water solution
has been used in the cleaning process. It MUST NOT be used with dry cleaning fluids. For
your safety, this dryer must be correctly installed.
If there is any doubt about installation, call the national GIAS Service number for advice.
Before using the tumble dryer for the
first time:
please read this instruction book
thoroughly.
remove all items packed inside drum.
wipe the inside of the drum and door
with a damp cloth to remove any dust
which may have settled in transit.
IMPORTANT: This dryer must only be
used for drying household textiles and
garments where a water solution has
been used for the cleaning process.
DO NOT tumble dry fabrics treated with
dry cleaning fluids.
Electrical requirements
This appliance is fitted with a moulded-on
non-rewireable plug.
The plug should be accessible for
disconnection after the appliance has been
installed.
IMPORTANT: The wires in the mains
lead are coloured in accordance with the
following code:
Blue - NEUTRAL
Brown - LIVE
Green-and-yellow - EARTH
If the supply cord on this appliance is
damaged, it must be replaced by a
special cord which is only available from
GIAS Service or an authorised Dealer.
WARNING!
ELECTRICITY CAN BE
EXTREMELY DANGEROUS.
THIS APPLIANCE MUST BE
EARTHED.
40001717ENG.fm Page 5 Saturday, July 10, 2004 7:32 PM
ENGLISH
6
Installation
requirements
IMPORTANT: This dryer must be
installed such that the air inlets and
outlets are not restricted (fig. 1).
1 - Supply cord
2 - Air inlets
3 - Air outlets
There should be a gap of at least 12 mm
(0.5 inches) between the sides rear and base
of the machine and the surrounding walls,
cabinets and floor.
To ensure adequate ventilation the space
between the bottom of the machine and the
floor must not be obstructed.
NEVER install the dryer up against
curtains.
Prevent items from falling or collecting
behind and beneath the dryer as these may
obstruct the air inlets and outlets.
Preparing the load
Before using the dryer for the first time
wipe the inside of the drum and door with a
damp cloth.
Make sure that the laundry you are going to
dry is suitable for drying in a tumble dryer,
as shown by the care symbols on each item.
Clothes preparation
Check that all fastenings are closed and that
pockets are empty. Turn the articles inside
out. Place clothes loosely in the drum to
make sure that they don’t get tangled.
Do not overload the drum, particularly
when drying large items, otherwise, the
laundry may stick to the drum and not dry
evenly.
Maximum drying weight
Cottons Max. 6 kg
Synthetics Max. 3 kg
Sort the load as follows:
A) By care symbols
On the collar or inside seam:
Suitable for tumble drying.
Tumble drying at high temperature.
Tumble drying at low temperature only.
Do not tumble dry.
B) By amount and thickness
Whenever the load is bigger than the
dryer capacity, separate clothes
according to thickness (e.g. towels
from thin underwear).
C) By type of fabric
Cottons/linen: Towels, cotton jersey,
bed and table linen.
Synthetics: Blouses, shirts, overalls,
etc. made of polyester or polyamid, as
well as for cotton/synthetic mixes.
40001717ENG.fm Page 6 Saturday, July 10, 2004 7:32 PM
7
ENGLISH
D) By drying level
Sort into: iron dry, cupboard dry, etc.
For delicate articles press the
‘DELICATES’ button to select low
drying temperature ( ).
For airing or drying very delicate
articles select the airing option on the
dial ( ).
Do not tumble dry:
Woollens, silk, delicate fabrics, nylon
stockings, delicate embroidery, fabrics
with metallic decorations, garments with
PVC or leather trimmings, training shoes,
bulky items such as sleeping bags, etc.
IMPORTANT: Do not dry articles
which have been treated with a dry
cleaning fluid or rubber clothes (danger
of fire or explosion).
Energy saving
Only put into the tumble dryer laundry
which has been thoroughly wrung or spin-
dried. The drier the laundry the shorter the
drying time thus saving electricity.
ALWAYS try to dry the maximum weight
of laundry, this will save time and
electricity.
NEVER exceed the maximum weight, this
will waste time and electricity.
ALWAYS check that the filter is clean
before every drying cycle as this aids
efficiency.
NEVER put dripping wet items into the
tumble dryer, this may damage the
appliance and waste time and efficiency.
Opening the door
Pull on handle to open the door (fig. 2).
To restart the dryer, close the door and
press the ‘ON’ button ().
Filter
IMPORTANT: To maintain the
efficiency of the dryer check that the
fluff filter is clean before each drying
cycle.
1. Pull the filter upwards (fig. 3).
2. Open filter as shown (fig. 4).
3. Gently remove lint using a soft brush or
your fingertips.
4. Snap the filter together and push back
into place.
Filter Care Indicator ( )
Lights when the filter needs cleaning.
If the laundry is not drying check that the
filter is not clogged.
WARNING!
WHEN THE TUMBLE DRYER
IS IN USE THE DRUM AND
DOOR MAY BE VERY HOT.
40001717ENG.fm Page 7 Saturday, July 10, 2004 7:32 PM
ENGLISH
8
Water Container
The water removed from the laundry
during the drying cycle is collected in a
container at the bottom of the dryer.
We recommend that the container is
emptied after each drying cycle.
To remove the container:
1. Gently pull the bottom of the kickplate
so that it unclips from the dryer (fig. 5).
The top section can then be unhinged
allowing the kickplate to be completely
removed.
2. Pull firmly on the handgrip and slide
the water container out of the dryer
(fig. 6). Support the container with both
hands. When full, the water container
will weigh about 4 kg (fig. 7).
3. Open the lid located on the top of the
container and empty the water (fig. 8).
4. Refit the lid and slide the water
container back into position. PUSH
FIRMLY INTO PLACE.
5. Refit the kickplate by engaging the
hinges at the top and ‘snapping’ the
lower clips into place.
Condenser
IMPORTANT: Always switch off and
remove the plug from the electricity
supply before cleaning the condenser.
To maintain the efficiency of the dryer
regularly check that the condenser is
clean.
To remove the condenser:
1. Remove the kickplate (fig. 5).
2. Turn the two locking levers anti-
clockwise (fig. 9).
3. Pull out the condenser unit (fig. 10).
4. Gently remove any dust or fluff with a
cloth, then wash the unit by holding it
under a running tap (fig. 11) turning it
so that water flows between the plates,
to remove any dust or fluff.
5. Refit the condenser ensuring it is
pushed firmly into place. Lock the two
levers by turning them clockwise.
6. Refit the kickplate.
40001717ENG.fm Page 8 Saturday, July 10, 2004 7:32 PM
9
ENGLISH
Drying guide
The table shows approximate drying times, depending on the type of fabric and dampness
of the clothes.
PRE-IRON PROGRAM: RELAXES CREASES – EASIER TO IRON
REMEMBER: During the last 10 minutes the load is always tumbled in cool air.
HEAT SETTING HEAVY LOAD MEDIUM LOAD LIGHT LOAD
COTTON
HIGH 120-140 Min 70-80 Min 30-50 Min
SYNTHETICS
LOW 70-80 Min 30-40 Min
ACRYLICS
LOW 50-65 Min 20-30 Min
40001717ENG.fm Page 9 Saturday, July 10, 2004 7:32 PM
ENGLISH
10
Control panel and indicator lights (fig. 12)
1. ‘ON’ button and indicator press to switch on, the indicator will light ().
2. ‘DELICATES’ button press to reduce the heat level for delicate items, press again
to select high temperature ( ).
HIGH Heat setting
LOW Heat setting
3. ‘DRYING TIME’ dial selects drying time or pre-ironing option.
4. ‘FILTER CARE’ indicator lights when filter needs cleaning ().
5. EMPTY WATER’ indicator lights when water container is full ( ).
40001717ENG.fm Page 10 Saturday, July 10, 2004 7:32 PM
11
ENGLISH
Operation
1. Open the door and load the drum with
laundry. Ensure that garments do not
hinder closure of the door.
2. If drying delicate items press the
‘DELICATES’ button to reduce the
heat level. Press again on completion,
to select high temperature.
HIGH Heat setting
LOW Heat setting
3. Turn ‘DRYING TIME’ dial until the
required drying time aligns with the
symbol T.
The Pre-ironing setting shown by the
symbol on the ‘DRYING TIME’
dial provides a conditioning and anti-
crease function. The dryer will heat the
load for 9 minutes followed by a 3
minute cool down period and is
especially good for garments which
may have been left for some time prior
to ironing, in a linen basket for
example. Garments may also become
stiffened when dried outside on a
washing line or inside on radiators. The
PRE-IRONING process relaxes the
creases in the fabric making ironing
quicker and easier.
4. Gently close the door pushing it slowly
until you hear the door ‘click’ shut.
5. Press the ‘ON’ button. The indicator
will light and the drying cycle begins.
6. The load is dried by tumbling in
thermostatically controlled warm air.
Cool air is used for the last 10 minutes
to reduce creasing and cool the load
ready for handling.
7. When the program is fully completed
the drum will stop rotating and the dial
will point to the symbol T.
Open the door and remove the load.
8. Clean the filter and empty the water
container after every drying cycle to
ensure maximum dryer efficiency.
(See ‘Filter’ and ‘Water Container’
sections.)
9. Clean the condenser after
approximately every 10 drying cycles
to ensure maximum dryer efficiency.
(See ‘Condenser’ section.)
WARNING!
THE DRUM, DOOR AND LOAD
MAY BE VERY HOT.
40001717ENG.fm Page 11 Saturday, July 10, 2004 7:32 PM
ENGLISH
12
Cleaning the dryer
IMPORTANT: Always switch off and
remove the plug from the electricity
supply before cleaning this appliance.
Clean the filter and empty the water
container after every drying cycle.
Regularly clean the condenser.
After each period of use, wipe the inside of
the drum and leave the door open for a
while to allow circulation of air to dry it.
Wipe the outside of the machine and the
door with a soft cloth.
DO NOT use abrasive pads or cleaning
agents.
To prevent the door sticking, periodically
clean the door gasket with a 'non-scratch
cream cleaner.'
Technical specifications
Drum capacity 115 litres
Maximum load 6 kg
Height 85 cm
Width 60 cm
Depth 60 cm
Energy Label Band C
Note: For electrical data refer to the rating
label on the front of the dryer cabinet (with
the door open).
40001717ENG.fm Page 12 Saturday, July 10, 2004 7:32 PM
13
ENGLISH
Trouble shooting
Should your dryer operate incorrectly,
check the following points before calling
for a service engineer.
Drying time is too long/clothes are not
dry enough:
Have you selected the correct drying
time/programme? Go to page 9.
Were the clothes too wet? Were the
clothes thoroughly wrung or spin-
dried?
Does the filter need cleaning? Go to
page 7.
Does the condenser need cleaning? Go
to page 8.
Is the dryer overloaded? Go to page 6.
Are the inlets, outlets and base of the
dryer free from obstructions?
Has the ‘DELICATES’ button been
selected from a previous cycle? Go to
page 10.
The dryer does not operate:
Is there a working electricity supply to
the dryer? Check using another
appliance such as a table lamp.
Is the plug properly connected to the
mains supply?
Is there a power failure?
Has the fuse blown?
Is the door fully closed? Go to page 11.
Is the dryer switched on, both at the
mains supply and at the machine? Go to
page 10.
Has the drying time or the programme
been selected? Go to page 10.
Has the machine been switched on
again after opening the door? Go to
page 7.
Has the dryer stopped operating
because the water tray is full and needs
emptying? Go to page 8.
Filter Care Indicator on
Does the filter need cleaning? Go to
page 7.
Empty Water Indicator on
Does the water container need
emptying? Go to page 8.
If the supply cord on this appliance is
damaged, it must be replaced by a special
cord which is only available from GIAS
Service or an authorised Dealer.
Should there still be a problem with your
dryer after completing all the
recommended checks, please call GIAS
Service for advice. They may be able to
assist you over the telephone or arrange for
a suitable appointment for an engineer to
call under the terms of your guarantee.
However, a charge may be made if any of
the following applies to your machine:
Is found to be in working order.
Has not been installed in accordance
with the installation instructions.
Has been used incorrectly.
40001717ENG.fm Page 13 Saturday, July 10, 2004 7:32 PM
FRANÇAIS
14
Rappels de sécurité
ATTENTION Vérifiez que la machine ne
présente aucun signe visible de détérioration
avant de l’utiliser. En cas de détérioration,
n’utilisez pas la machine et veuillez contacter
Service GIAS.
ATTENTION N’utilisez pas cette machine si
le filtre à peluches n’est pas en place ou s’il est
endommagé ; les peluches risquent en effet de
s’allumer.
ATTENTION Quand elles sont chauffées, les
mousses alvéolaires peuvent dans certains cas
brûler par combustion spontanée. Les articles
en plastique alvéolaire, en caoutchouc
alvéolaire et en caoutchouc ne conviennent pas
au séchage en machine. Les articles fabriqués à
partir de ces matériaux NE DOIVENT PAS être
placés dans le sèche-linge.
Reportez-vous toujours aux étiquettes
d’entretien du linge pour vérifier le mode de
séchage recommandé.
ATTENTION La mauvaise utilisation d’un
sèche-linge risque de causer un incendie.
ATTENTION L’augmentation de température
pendant le fonctionnement du sèche-linge peut
être supérieure à 60°C là où se trouve le
symbole de surface chaude .
Manuel de l’utilisateur. Cette machine ne doit
être utilisée que pour l’emploi auquel elle est
destinée et qui est décrit dans ce manuel. Veillez
à bien comprendre ce manuel avant d’utiliser la
machine.
Installation. Cette machine ne doit pas être
installée dans une salle de bain ou de douche.
Veillez à ne pas installer le sèche-linge contre
des rideaux et assurez-vous que rien ne pourra
tomber ou s’accumuler derrière le sèche-linge.
Ventilation. La pièce où se trouve le sèche-
linge doit avoir une ventilation adéquate de
manière à ce que les gaz des appareils qui
brûlent d’autres combustibles, y compris les
cheminées, ne soient pas attirés dans la pièce
pendant que le sèche-linge est en marche.
L’air d’échappement ne doit pas être évacué par
un conduit qui est également utilisé pour
évacuer les fumées d’échappement d’appareils
qui brûlent du gaz ou d’autres combustibles.
Vérifiez régulièrement que l’air peut circuler
librement dans le sèche-linge :
Vérifiez le filtre à peluches après usage, et
nettoyez-le le cas échéant.
Il est nécessaire d’inspecter régulièrement le
tuyau ou la conduite de ventilation et d’éliminer
les accumulations éventuelles de peluches.
Les entrées et sorties doivent être libres
d’obstructions.
Si le sèche-linge est utilisé fréquemment, les
intervalles entre les inspections doivent être
réduits en conséquence.
Degré de séchage. Les vêtements doivent être
essorés en machine ou à la main avant d’être
placés dans le sèche-linge. Les vêtements qui
dégoulinent NE DOIVENT PAS être mis dans
le sèche-linge.
Enlevez les briquets et les allumettes des
poches et veillez à ne JAMAIS utiliser de
liquides inflammables à proximité de la
machine.
Les rideaux en fibres de verre ne doivent
jamais être placés dans cette machine. La
contamination d’autres vêtements par les fibres
de verre peut entraîner des irritations de la peau.
Les vêtements traités ou contaminés par des
produits de nettoyage ou des liquides
inflammables, comme l’essence, l’huile de
cuisson ou les aérosols ne doivent pas être
placés dans la machine.
Veillez à ce que les peluches ne puissent pas
s’accumuler sur le sol, à l’extérieur de la
machine.
Période de refroidissement. Il se peut que
l’intérieur du tambour soit très chaud. Veillez à
ce que le sèche-linge termine son cycle de
refroidissement avant d’en sortir le linge.
Pannes. Cessez d’utiliser la machine si elle
semble défectueuse.
Après usage. Débranchez du courant de
secteur. Retirez toujours la prise avant de
nettoyer la machine.
Cordon d’alimentation. Si le cordon
d’alimentation de cet appareil est endommagé,
il doit être remplacé par un cordon spécial
exclusivement disponible auprès de GIAS
Service ou d’un distributeur agréé.
Service GIAS. Pour veiller au fonctionnement
sûr et efficace de cet appareil, il est conseillé de
faire appel à un technicien agréé pour les
entretiens et les réparations.
40001717FRE.fm Page 14 Sunday, July 11, 2004 1:41 PM
15
FRANÇAIS
Rappels de sécurité 14 Filtre 17
Besoins électriques 15 Réservoir d’eau 18
Besoins d’installation 16 Condenseur 18
Préparation de la charge 16 Guide de séchage 19
Préparation des vêtements 16 Commandes & témoins 20
Poids de séchage maximum 16 Fonctionnement 21
Tri de la charge 16-17 Nettoyage du sèche-linge 22
Ne séchez pas en machine 17 Spécification technique 22
Economies d’énergie 17 Dépistage de pannes 23
Ouverture de la porte 17 Garantie 24
VEUILLEZ LIRE CES INSTRUCTIONS EN DETAIL
L’utilisation de cet appareil doit respecter les instructions qui figurent dans ce manuel. Il
est prévu pour usage domestique uniquement, afin de sécher le linge de maison et les
vêtements qui ont été nettoyés avec une solution aqueuse. Il NE DOIT PAS être utilisé avec
des liquides de nettoyage à sec. Par mesure de sécurité, veillez à installer ce sèche-linge
correctement.
En cas de doute concernant l’installation, veuillez appeler le numéro de Service GIAS
national pour obtenir des conseils.
Avant d’utiliser le sèche-linge pour la
première fois :
veuillez lire ce manuel d’instruction en
détail.
retirez tous les articles qui se trouvent à
l’intérieur du tambour.
essuyez l’intérieur du tambour et de la
porte avec un chiffon humide pour
éliminer la poussière éventuelle qui
aurait pu s’y infiltrer en transit.
IMPORTANT : Ce sèche-linge doit être
utilisé exclusivement pour sécher le linge
de maison et les vêtements qui ont été
nettoyés avec une solution aqueuse.
NE séchez PAS les tissus qui ont été
traités avec des liquides de nettoyage à
sec.
Besoins électriques
Cet appareil est équipé d’une fiche moulée
qu’il est impossible de recâbler.
La fiche doit être accessible pour
débrancher l’appareil une fois qu’il a été
installé.
IMPORTANT : Les fils du câble de
secteur sont codés par couleur, comme
suit :
Bleu - NEUTRE
Marron - SOUS TENSION
Vert et jaune - TERRE
Si le cordon d’alimentation de cet
appareil est endommagé, il doit être
remplacé par un cordon spécial
exclusivement disponible auprès de
GIAS Service ou d’un distributeur
agréé.
ATTENTION !
L’ELECTRICITE PEUT ETRE
EXTREMEMENT DANGEREUSE.
CET APPAREIL DOIT ETRE MIS A
LA TERRE.
40001717FRE.fm Page 15 Sunday, July 11, 2004 1:41 PM
FRANÇAIS
16
Besoins d’installation
IMPORTANT : Ce sèche-linge doit être
installé de manière à ce que les entrées et
sorties d’air ne soient pas obstruées
(fig.1).
1 – Cordon d’alimentation
2 – Entrées d’air
3 – Sorties d’air
Il doit y avoir un espace d’au moins 12 mm
entre les côtés, l’arrière et le bas de la
machine et les murs, les armoires et le sol
qui l’entourent.
Pour veiller à une ventilation adéquate,
l’espace entre le bas de la machine et le sol
ne doit pas être obstrué.
N’installez JAMAIS le sèche-linge contre
des rideaux.
Veillez à ce que rien ne puisse tomber ou
s’accumuler derrière ou sous le sèche-linge
afin de ne pas obstruer les entrée et sorties
d’air.
Préparation de la charge
Avant d’utiliser le sèche-linge pour la
première fois, essuyez l’intérieur du
tambour et de la porte à l’aide d’un chiffon
humide.
Vérifiez sur les étiquettes comportant les
symboles d’entretien que le linge que vous
souhaitez sécher convient au séchage en
machine.
Préparation des
vêtements
Vérifiez que toutes les fermetures sont
fermées et que les poches sont vides.
Mettez les articles à l’envers. Placez les
vêtements en vrac dans le tambour en
veillant à ce qu’ils ne s’emmêlent pas les
uns avec les autres.
Ne surchargez pas le tambour,
particulièrement lorsque vous séchez de
grands articles, sinon le linge risque
d’adhérer au tambour et de ne pas sécher de
manière uniforme.
Poids de séchage
maximum
Coton, 6 kg maxi
Synthétiques, 3 kg maxi
Triez la charge comme
suit :
A) Par symbole de soin d’entretien
Sur le col ou la couture intérieure :
Convient pour séchage en machine.
Séchage à haute température.
Séchage à basse température
uniquement.
Ne pas sécher en machine.
B) Par quantité et épaisseur
Lorsque la charge est plus importante
que la capacité du sèche-linge, séparez
les vêtements selon leur épaisseur (ex :
les serviettes des sous-vêtements fins).
C) Par type de tissu
Coton/toile de lin : Serviettes, jersey en
coton, linge de lit ou de table.
Synthétiques : Chemisiers, chemises,
blouses, etc. en polyester ou polyamide
ainsi que les mélanges de coton/
synthétique.
D) Par degré de séchage
Triez selon : Sec pour repassage, sec
pour rangement, etc.
Pour les articles délicats, appuyez sur le
bouton pour sélectionner une
température de séchage basse.
40001717FRE.fm Page 16 Sunday, July 11, 2004 1:41 PM
17
FRANÇAIS
Sélectionnez l’option aération sur le
cadran pour l’aération ou le séchage
d’articles très délicats ( ).
Ne séchez pas en
machine :
Les lainages, la soie, les tissus délicats, les
bas de nylon, les broderies délicates, les
tissus ayant des décorations métalliques,
les vêtements avec des bordures en PVC ou
en cuir, les chaussures de sport, les articles
volumineux comme les sacs de couchage,
etc.
IMPORTANT : Ne séchez pas les
articles qui ont été traités avec un liquide
de nettoyage à sec ou les vêtements en
caoutchouc (risque d’incendie ou
d’explosion).
Economies d’énergie
Ne mettez que du linge essoré en machine
ou à la main dans le sèche-linge. Plus le
linge est sec, plus le temps de séchage sera
court, ce qui économisera de l’énergie.
Essayez TOUJOURS de sécher le poids de
linge maximum, pour économiser du temps
et de l’électricité.
Ne dépassez JAMAIS le poids maximum
pour ne pas gaspiller du temps ou de
l’électricité.
Vérifiez TOUJOURS que le filtre est
propre avant chaque cycle de séchage, pour
assurer une efficacité de séchage
maximale.
Ne mettez JAMAIS d’articles dégoulinant
d’eau dans le sèche-linge, pour ne pas
endommager la machine et perdre du temps
et de l’efficacité.
Ouverture de la porte
Tirez sur la poignée pour ouvrir la porte
(fig. 2).
Pour remettre le sèche-linge en marche,
fermez la porte et appuyez sur le
bouton .
Filtre
IMPORTANT : Pour assurer l’efficacité
du sèche-linge, vérifiez que le filtre à
peluches est propre avant chaque cycle
de séchage.
1. Tirez le filtre vers le haut (fig. 3).
2. Ouvrez le filtre, comme illustré (fig. 4).
3. Retirez doucement les peluches à l’aide
d’une brosse douce ou du bout des
doigts.
4. Réenclenchez le filtre et poussez-le en
place.
Indicateur d’entretien du filtre ( )
S’allume lorsqu’il faut nettoyer le filtre.
Si le linge ne sèche pas, vérifiez que le filtre
n’est pas colmaté.
ATTENTION !
LORSQUE LE SECHE-LINGE EST
EN COURS D’UTILISATION, IL SE
PEUT QUE LE TAMBOUR ET LA
PORTE SOIENT TRES CHAUDS.
40001717FRE.fm Page 17 Sunday, July 11, 2004 1:41 PM
FRANÇAIS
18
Réservoir d’eau
L’eau récupérée du linge pendant le cycle
de séchage est recueillie dans un réservoir
situé en bas du sèche-linge.
Nous recommandons de vider le
réservoir après chaque cycle de séchage.
Pour retirer le réservoir :
1. Tirez doucement le bas de la plaque de
protection pour la décrocher du sèche-
linge (fig. 5). La section supérieure
peut être ôtée de ses charnières pour
permettre le retrait total de la plaque de
protection.
2. Tirez fermement sur la poignée et faites
glisser le réservoir d’eau en dehors du
sèche-linge (fig. 6). Tenez-le
fermement à deux mains. Lorsque le
bac est plein, il pèse environ 4 kg
(fig. 7).
3. Ouvrez le couvercle qui se trouve sur le
dessus du bac et videz l’eau (fig. 8).
4. Refermez le couvercle et glissez le bac
de récupération de l’eau dans sa
position. POUSSEZ-LE
FERMEMENT EN PLACE.
5. Remettez la plaque de protection en
place en engageant les charnières du
haut et en enclenchant les attaches
inférieures en place.
Condenseur
IMPORTANT : Coupez toujours le
courant et débranchez la prise avant de
nettoyer le condenseur.
Pour maintenir l’efficacité du sèche-
linge, vérifiez régulièrement la propreté
du condenseur.
Pour retirer le condenseur :
1. Retirez la plaque de protection (fig. 5).
2. Tournez les deux leviers de blocage
dans le sens contraire des aiguilles
d’une montre (fig. 9).
3. Tirez l’ensemble du condenseur vers
l’extérieur (fig. 10).
4. Retirez doucement la poussière ou les
peluches avec un chiffon, puis lavez-le
en le tenant sous un robinet d’eau
(fig. 11) pour que l’eau coule entre les
plaques afin d’enlever la poussière ou
les peluches éventuelles.
5. Remettez le condenseur en place le
poussant fermement. Bloquez les deux
leviers en position en les tournant dans
le sens des aiguilles d’une montre.
6. Remettez la plaque de protection en
place.
40001717FRE.fm Page 18 Sunday, July 11, 2004 1:41 PM
19
FRANÇAIS
Guide de séchage
Ce tableau indique les temps de séchage approximatifs, selon le type de tissu et le degré
d’humidité des vêtements.
PROGRAMME PRE-REPASSAGE : ANTI-FROISSEMENT –
PLUS FACILE A REPASSER
ATTENTION : Pendant les 10 dernières minutes, la charge est toujours séchée dans de
l’air froid.
PUISSANCE DE
SECHAGE
PLEINE
CHARGE
1/2 CHARGE
PETITE
CHARGE
COTON
HAUT 120-140 min 70-80 min 30-50 min
SYNTHETIQUES
BAS 70-80 min 30-40 min
ACRYLIQUE
BAS 50-65 min 20-30 min
40001717FRE.fm Page 19 Sunday, July 11, 2004 1:41 PM
FRANÇAIS
20
Panneau de commande et témoins indicateurs
(fig. 12)
1. Bouton et indicateur appuyez pour mettre en marche ; l’indicateur s’allumera.
2. Bouton appuyez pour diminuer le niveau de chaleur, pour les articles délicats, et
appuyez à nouveau pour sélectionner une température élevée.
Puissance de séchage HAUTE
Puissance de séchage BASSE
3. Cadran ‘TEMPS DE SECHAGE’ sélectionne le temps de séchage ou l’option de
pré-repassage.
4. L’indicateur s’allume lorsque le filtre a besoin d’être nettoyé.
5. L’indicateur s’allume lorsque le réservoir d’eau est plein.
40001717FRE.fm Page 20 Sunday, July 11, 2004 1:41 PM
1 / 1