Maytag MDE25PN Installation Instructions Manual

INSTALLATION

INSTRUCTIONS

CommerCial He Dryer

eleCtriC

INSTRUCTIONS

D’INSTALLATION

SèCHe-linge He CommerCial

eleCtrique

INSTRUCCIONES

DE INSTALACIÓN

SeCaDora He ComerCial

eléCtriCa

ISTRUZIONI

D’INSTALLAZIONE

aSCiugatriCe He CommerCiale

elettriCa

www.maytagcommerciallaundry.comW10746731A

MDE25PN

MDE25PD

2

TABLE OF CONTENTS

Page

Dryer Safety ............................................................................ 3

Dryer Disposal ........................................................................ 5

Tools & Parts .......................................................................... 6

Dimensions/Clearances ........................................................ 7

Installation Requirements ..................................................... 8

Venting Requirements ......................................................... 10

Installing Leveling Legs, Coin Slide, and Coin Box .......... 13

Leveling ................................................................................ 14

Complete Installation .......................................................... 15

Reversing Door Swing (optional) ........................................ 16

Maintenance Instructions ................................................... 18

If You Need Assistance ....................................................... 18

Electronic Control Setup Instructions ............................... 19

Warranty ............................................................................... 24

TABLE DES MATIÈRES

Page

Sécurité du sèche-linge ........................................................ 25

Élimination du sèche-linge ................................................... 27

Outils et pièces ..................................................................... 28

Dimensions/Distances de dégagement ............................. 29

Exigences d’installation ....................................................... 30

Exigences concernant l’évacuation .................................... 32

Installation des pieds de nivellement, de la glissière

à monnaie et de la caisse à monnaie .................................. 35

Nivellement ........................................................................... 36

Achever l’installation ............................................................ 37

Inversion du sens d’ouverture de la porte (facultatif) ........ 38

Instructions d’entretien ........................................................ 40

Si vous avez besoin d’assistance ....................................... 40

Instructions de réglage du tableau

de commande électronique ................................................. 41

Garantie ................................................................................. 47

ÍNDICE

Página

Seguridad de la secadora ..................................................... 48

Eliminación de la secadora .................................................. 50

Herramientas y piezas .......................................................... 51

Dimensiones y espacios libres ............................................ 52

Requisitos de instalación ..................................................... 53

Requisitos de ventilación ..................................................... 55

Instalación de las patas, del tragamonedas

y la caja de monedas ............................................................ 58

Nivelación .............................................................................. 59

Complete la instalación ....................................................... 60

Cómo invertir el cierre de la puerta (opcional) .................. 61

Instrucciones de mantenimiento ......................................... 63

Si necesita ayuda ................................................................. 63

Instrucciones de programación

del control electrónico ......................................................... 64

Garantía ................................................................................. 70

INDICE

Pagina

Sicurezza dell’asciugatrice .................................................. 71

Eliminazione dell’asciugatrice ............................................. 73

Attrezzi e componenti ......................................................... 74

Dimensioni/spazi ................................................................. 75

Requisiti dell’installazione .................................................. 76

Requisiti di scarico .............................................................. 78

Installazione dei piedini di regolazione, dello scivolo

monete e del salvadanaio ................................................... 81

Livellamento ......................................................................... 82

Completamento dell’installazione ..................................... 83

Inversione della rotazione di apertura (facoltativo) .......... 84

Istruzioni di manutenzione .................................................. 86

Se avete bisogno dell’assistenza ....................................... 86

Congurazione dei controlli elettronici ............................. 87

Garanzia ............................................................................... 93

3

DRYER SAFETY

FOR YOUR SAFETY

1. DO NOT USE OR STORE PETROL OR OTHER FLAMMABLE MATERIALS IN THIS APPLIANCE OR NEAR THIS APPLIANCE.

2. DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

3. DO NOT MODIFY THIS APPLIANCE.

4

DRYER SAFETY

n Do not install or store the dryer where it will be exposed

to the weather.

n Do not tamper with controls.

n Clean dryer lint screen before or after each load.

n Do not use this dryer without the lint screen in place.

n Do not repair or replace any part of the dryer or attempt

any servicing unless specically recommended in

this Use and Care Guide or in published user-repair

instructions that you understand and have the skills

to carry out.

n Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

n Do not use heat to dry articles containing foam rubber

or similarly textured rubber-like materials.

n The nal part of a tumble dryer cycle occurs without

heat (cool-down cycle) to ensure that the articles are left

at a temperature that ensures that the items will not be

damaged.

n WARNING: Never stop a tumble dryer before the end

of the drying cycle unless all items are quickly removed

and spread out so that the heat is dissipated. (Avoids risk

of spontaneous combustion).

n In case of electrical supply failure, remove the load

quickly and spread it out to avoid risk of spontaneous

combustion.

n Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

n The fresh air ventilation openings into the room and into

the dryer must not be blocked or sealed.

n Emergency stop control: After installation, access to

mains plug or disconnection from mains supply via a

double-pole switch must be ensured at all times in order

to ensure immediate deactivation of the dryer in case of

emergency.

n The interior of the dryer and dryer exhaust vent should be

cleaned periodically by qualied service personnel.

n See “Electrical Requirements” section for earthing

instructions.

n The dryer shall be disconnected from its power source

during service and when replacing parts. If the removal

of the plug is foreseen, it shall be clearly indicated that it

be possible for the operator to conrm the removal of the

plug from any point of access.

If this is not possible due to the construction of the

appliance or its installation, a disconnection with a

locking system in the isolated position shall be provided.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of re, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

SAVE THESE INSTRUCTIONS

n Read all instructions before using the dryer.

n This dryer is intended only for drying clothes and textiles

that have been washed in water. Do not use for any other

purpose.

n Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch re.

n If it is unavoidable that fabrics that contain vegetable or

cooking oil or that have been contaminated by hair care

products be placed in a tumble dryer, they should rst

be washed in hot water with extra detergent – this will

reduce, but not eliminate the hazard.

n Do not dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with petrol,

dry-cleaning solvents, other ammable, or explosive

substances as they give off vapors that could ignite

or explode.

n Items that have been soiled with substances such

as acetone, alcohol, petrol, kerosene, spot removers,

turpentine, waxes, and wax removers should be washed

in hot water with extra detergent before being dried in

the dryer.

n Do not dry unwashed items in the dryer.

n Do not use this dryer if industrial chemicals have been

used for cleaning. The possible presence of residual

quantities of aggressive or decomposed chemicals in

the load may produce damage to the dryer and harmful

fumes.

n Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

n This dryer is not intended for use by persons (including

children) with reduced physical, sensory, or mental

capabilities, or lack of experience or knowledge,

unless they have been given supervision or instruction

concerning use of the dryer by a person responsible

for their safety.

n Before the dryer is removed from service or discarded,

remove the door to the dryer compartment.

n Do not reach into the dryer if the drum is moving.

n Opening the dryer door will stop the function of the dryer.

n When loading or re-loading the dryer, avoid touching hot

metal parts of the drum (burn risk).

n If drum rotation is blocked due to trapped textiles,

disconnect the dryer from the electrical supply before

gently removing the blockage.

n If the dryer is not heating, or appears to be defective or

damaged, do not use it. Contact the owner.

5

DRYER DISPOSAL

This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment

(WEEE).

By ensuring this product is disposed of correctly, you will help avoid potential negative consequences for the environment

and human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be

treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical

and electronic equipment.

Disposal must be carried out in accordance with local environmental regulations for waste disposal.

For more detailed information about treatment, recovery and recycling of this product, please contact your local city ofce,

your household waste disposal service or the shop where you purchased the product.

MODEL NOMENCLATURE:

MDE – Maytag Dryer – Electric PN – Electronic Control – Non-Pay

## (e.g. 25) – Model Type Number PD – Electronic Control – Coin Drop Enabled

6

Tools Needed:

203 mm (8") 203 mm (8") or 254 mm (10") Flat-blade screwdriver Phillips screwdriver

or 254 mm (10") Adjustable wrench

Pipe wrench that opens to 25 mm (1")

Torx T20

®†

Security 25 mm (1") Hex-head 8 mm (5/16") Socket wrench Pliers

screwdriver or bit socket wrench (that open to 39 mm [1

9

/

16

"])

Level Utility knife 6 mm (1/4") Nut driver Locking pliers

Caulk gun and caulk Vent clamps Pipe-joint compound 686 mm (27") Wood block

(for installing new exhaust vent) suitable for gas type

Flashlight (optional) 13 mm (1/2") and 14 mm Ruler or measuring tape Putty knife

(9/16") Open-end wrenches

TOOLS & PARTS

†® TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

NOTE: The circuit diagram for this dryer is located inside the lower front panel, within the Tech Sheets.

Parts Supplied:

Foot boots (4) Leveling legs (4) PD models: Cam for service PN models: Card reader

door lock bezel, card reader wire

harness, hardware

NOISE: Sound Pressure Level, Lpa: 58 dBA (uncertainty,

Kpa: +/–10 dBA).

Technical Specications: Clothes Capacity:

220–240 V, 50 HZ. AC 4575 W 9 kg max.

Total mass: 68 kg max.

7

DIMENSIONS/CLEARANCES

Front View Side View Back View

Dimensions

Clearances

Recessed Front View

686 mm

(27")

965 mm

(38")

25 mm

(

1"

)

736 mm

(29")

921 mm

(36

1

/4")

25 mm

(

1"

)

695 mm

(27

1

/4")

203 mm

(8")

356 mm

(14")

25 mm

(1")

0 mm

(0")

381 mm

(15")

0 mm

(0")

159 mm

(6

1

/4")

715 mm

(28

1

/8")

89 mm

(3

1

/2")

358 mm

(14")

Closet Side View

8

Your dryer can be installed in a basement, laundry room,

or recessed area.

Companion appliance location requirements should also

be considered.

IMPORTANT: Do not install or store the dryer where it

will be exposed to the weather. Proper installation is your

responsibility.

You will need:

n A level oor with a maximum slope of 25 mm (1") under

entire dryer. Installing the dryer on soft oor surfaces,

such as carpets or surfaces with foam backing, is not

recommended.

n A sturdy and solid oor to support the dryer with a total

weight (load) of 204 kg (450 lbs).

Installation clearances

n The location must be large enough to allow the dryer door

to be fully opened.

n Additional spacing should be considered for ease of

installation and servicing. The door opens more than 180°.

n Additional clearances might be required for wall, door,

and oor moldings.

n Additional spacing of 25 mm (1") on all sides of the dryer

is recommended to reduce noise transfer.

n Companion appliance spacing should also be considered.

Location

INSTALLATION REQUIREMENTS

Recessed Area and Closet Installation Instructions

This dryer may be installed in a recessed area or closet. The

dryer must not be installed behind a lockable door, a sliding door,

or a door with a hinge on the opposite side to that of the dryer

in such a way that a full opening of the dryer door is restricted.

For recessed area and closet installations, minimum clearances

can be found on the warning label on the rear of the dryer or in

“Dimensions/Clearances.”

The installation spacing is in millimeters and is the minimum

allowable. Additional spacing should be considered for ease

of installation, servicing, and compliance with local codes

and ordinances.

If closet door is installed, the minimum unobstructed air

opening in the top and bottom is required. Louvered doors

with equivalent air openings are acceptable.

The dryer must be exhausted outdoors.

NOTE: For installation in Australia and New Zealand, refer

to AS/NZS 5601.1 for ventilation requirements.

9

INSTALLATION REQUIREMENTS

Electrical Requirements

This is 3-wire appliance which must be earthed.

This dryer is supplied without an electric cord and plug.

It must be connected by a competent electrician to a single-

phase electricity supply at the voltage shown on the dataplate,

using a suitable xed wiring installation in accordance with local

and national wiring regulations.

n A 3-wire circular cord of minimum conductor size 2.5 mm

2

cross-section area should be used.

n A 30A supply fuse should be used, and a switch having

a contact separation in both poles that provides full

disconnection under over-voltage category III conditions

must be incorporated into the xed wiring in accordance

with local wiring regulations. The dryer should be positioned

so that the disconnection switch is clearly visible and easily

accessible to the user. This disconnection switch also

provides the function of an emergency stop control

for the user.

n A cord clamp bush is provided on the dryer, and should

be tightened on completion of wiring. The electrical mains

terminals are located behind the small rear access panel

(terminal block cover), and connections should be made

in accordance with the terminal markings. Remember to

replace the terminal access panel (terminal block cover).

NOTE: In accordance with the European EMC Directive

(2004/108/EC), the maximum electricity supply system

impedance to which the electric dryer should be connected

is declared to be 0.054 Ohm + j0.034 Ohm.

NOTE: Electrical safety standards: The manufacturer has

chosen compliance with IEC/EN.60335 standards as the

most appropriate for this product.

If codes permit and an additional earth bond wire is used,

it is recommended that a qualied electrician determine that

the earth bond path is adequate.

AUSTRALIA ONLY

For Australia, each single electric dryer is tted with a cord

and plug, with conductors of 2.5 mm

2

cross sectional area,

and should be plugged into a suitable electrical socket at the

voltage shown on the dataplate. Do not use extension lead

assemblies on commercial installations. If the supply cord is

damaged, it must be replaced with a specially terminated cord

by an authorized service agent or a similarly qualied person in

order to avoid a hazard. Each electric dryer for other countries

is supplied without an electric cord and plug.

Recommended Earthing Method

It is your responsibility to contact a qualied electrical installer

to ensure that the electrical installation is adequate and in

conformance with all local codes and ordinances.

10

VENTING REQUIREMENTS

WARNING: To reduce the risk of re, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

■ Following these venting requirements will minimise ducting

air noise.

■ Adequate ventilation has to be provided to avoid the

backow of gases into the room from appliances burning

other fuels, including open res (i.e. available airow into

the room should match airow out from the room).

■ Dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, attic, crawlspace, or a concealed

space of a building. Only rigid or exible metal vent shall

be used for exhausting.

■ Do not use an exhaust hood with a magnetic latch.

■ Only a 102 mm (4") heavy, metal exhaust vent and clamps

may be used.

■ Do not use plastic or metal foil vent.

Rigid metal vent:

■ Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

■ Must be fully extended and supported in nal dryer location.

■ Remove excess to avoid sagging and kinking that may

result in reduced airow and poor performance.

■ Do not install in enclosed walls, ceilings, or oors.

■ The total length should not exceed 2.4 m (7

3

⁄

4

ft.).

■ An exhaust hood should cap the vent to keep rodents and

insects from entering the building.

NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not

plugged with lint. Replace plastic or metal foil vents with rigid

metal or exible metal vents. Review “Vent System Chart” and

if necessary, modify existing vent system to achieve best drying

performance.

102 mm

(

4"

)

102 mm (4") heavy, metal exhaust vent

Elbows:

■ 45° elbows provide better airow than 90° elbows.

■ Plan installation to use the fewest number of elbows

and turns.

■ Allow as much room as possible when using elbows

or making turns. Bend vent gradually to avoid kinking.

■ Vent outlet is located at the center of the bottom dryer back.

■ The vent can be routed up, down, left, right, behind the

dryer, or straight out the back of the dryer.

Clamps:

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with

screws or other fastening devices that extend into interior

of duct and catch lint. Do not use duct tape.

Better

Good

11

12" min.

(305 mm)

102 mm (4") Diameter Exhaust Hoods

Box hood Louvered hood Angled hood

Vent Hoods

VENTING REQUIREMENTS

Exhaust hood must be at least 305 mm (12") from the ground

or any object that may be in the path of the exhaust (such as

owers, rocks, bushes, or snow).

Maximum Vent Length/Vent Connection

Maximum length of vent system depends upon the type of vent

used, number of elbows, and type of exhaust hood.

Vent System Chart (Rigid Metal Vent)

No. of 90˚ Turns

Box and

Louvered Hood

Angled Hood

0 39.6 m (130 ft.) 39.3 m (129 ft.)

1 38.1 m (125 ft.) 36.3 m (119 ft.)

2 35.1 m (115 ft.) 33.2 m (109 ft.)

3 32.3 m (106 ft.) 30.5 m (100 ft.)

4 29.9 m (98 ft.) 28.0 m (92 ft.)

For vent systems not covered by the “Vent Specication Chart,”

see your parts distributor.

Provision must be made for enough air for combustion and

ventilation. (Check governing codes and ordinances.) See

“Recessed Area and Closet Installation Instructions” in the

“Location” section.

A 102 mm (4") outlet hood is preferred. However, a 64 mm

(2

1

⁄

2

") outlet exhaust hood may be used. A 64 mm (2

1

⁄

2

") outlet

creates greater back pressure than other hood types. For

permanent installation, a stationary vent system is required.

Connect Vent

1. If connecting to existing vent, make sure the vent is clean.

2. Using a 102 mm (4") clamp, connect vent to exhaust outlet

in dryer.

NOTE: Do not remove vent collar.

Vent System Length

3. Tighten hose clamp with Phillips screwdriver.

4. Make sure the vent is secured to exhaust hood with

a 102 mm (4") clamp.

5. Move dryer into nal position. Do not crush or kink vent.

Make sure dryer is level.

Vent collar

305 mm min.

(12")

12

The outside end of main vent should have a sweep elbow

directed downward.

If main vent travels vertically through the roof, rather than

through wall, install a 180° sweep elbow on end of vent at least

610 mm (2 ft.) above surface of roof.

The opening in wall or roof shall have a diameter 13 mm (1⁄2")

larger than vent diameter. Vent should be centered in opening.

Do not install screening over end of vent for best performance.

A main vent can be used for venting a group of dryers. The

main vent should be sized to remove 5663 l/min. (200 CFM)

of air per dryer. Large-capacity lint screens of proper design

may be used in main vent if checked and cleaned frequently.

The room where the dryers are located should have make-up

air equal to or greater than CFM of all the dryers in the room.

Back-draft Damper Kit, Part No. 3391910, is available from

your distributor and should be installed in the vent of each

dryer to keep exhausted air from returning into dryers and to

keep exhaust in balance within main vent. Unobstructed return

air openings are required.

Each vent should enter the main vent at an angle pointing in

the direction of the airow. Vents entering from the opposite

side should be staggered to reduce the exhausted air from

interfering with the other vents.

The maximum angle of each vent entering the main vent should

be no more than 30°.

Keep air openings free of dry cleaning uid fumes. Fumes

create acids which, when drawn through the dryer heating

units, can damage dryers and items being dried.

A clean-out cover should be located on the main vent for

periodic cleaning of the vent system.

If an Exhaust Hood Cannot be Used Multiple Dryer Venting

VENTING REQUIREMENTS

30˚ max.

air ow

* Minimum clearance above

any accumulation of snow,

ice, or debris such as leaves

13

INSTALLING LEVELING LEGS, COIN SLIDE, AND COIN BOX

The coin slide mechanism, control panel lock and key, and

coin box lock and key are not included and are available from

usual industry sources. A special coin slide extension must be

used on this model and can be purchased from the coin slide

distributor.

1. Prepare dryer for leveling legs

NOTE: Slide dryer onto cardboard or hardboard before moving

to avoid damaging oor covering.

Using two or more people, move dryer to desired installation

location.

Take tape off front corners of dryer. Open dryer and remove

the literature and parts packages. Wipe drum interior with damp

cloth to remove any dust.

Take two cardboard corners from the dryer carton and place

them on the oor in back of the dryer. Firmly grasp body of the

dryer and gently lay it on its back on the cardboard corners.

2. Screw in leveling legs

Examine leveling legs and nd diamond

marking. Screw legs into leg holes by

hand. Use an adjustable wrench or

25 mm (1") hex-head socket wrench to

nish turning legs until diamond marking

is no longer visible. Then t a covered foot

boot over each leg foot.

To protect the oor, use a large piece of cardboard from the

dryer carton. Stand dryer up on the cardboard. Slide the dryer

until it is close to its nal location. Leave enough room for

electrical connection and to connect the exhaust vent.

3. Install coin slide and coin box

Remove the service door of the meter case by lifting it up

at the back. Install the money-accepting device. (Refer to

manufacturer’s instructions for proper installation.)

Replace the meter case service door. Put the coin vault with

lock and key in the meter case opening.

Remove cardboard or hardboard from under dryer. Adjust the

legs of the dryer up or down until the dryer is level.

Foot

Diamond

marking

14

1. Remove cardboard from beneath dryer. Place a level on top

edges of dryer, checking each side and front. If not level, tip

dryer and adjust feet up or down as shown in Steps 3 and 4,

repeating as necessary.

LEVELING

Leveling your dryer properly reduces excess noise and vibration.

Not Level LEVEL Not Level

2. Grip dryer from top and rock back and forth, making sure all

four feet are rmly on oor. Repeat, rocking dryer from side

to side. If dryer rocks, go to Step 3 and adjust leveling feet.

If all four feet are in rm contact with oor, go to Step 4.

4. When dryer is level and all four feet are rmly in contact with

the oor, use a 14 mm or 9/16" open-end or adjustable

wrench to turn jam nuts counterclockwise (as viewed from

above) on leveling feet tightly against dryer cabinet.

HELPFUL TIP: You may want to prop dryer with wooden

block.

3. If dryer is not level, use a 14 mm or 9/16" open-end or

adjustable wrench to turn jam nuts clockwise (as viewed from

above) on feet until they are about 13 mm (1/2") from the dryer

cabinet. Then turn the leveling foot counterclockwise to lower

the dryer or clockwise to raise the dryer. Recheck levelness of

dryer and that all four feet are rmly in contact with the oor.

Repeat as needed.

HELPFUL TIP: You may want to prop up front of dryer about

102 mm (4") with a wood block or similar object that will

support weight of dryer.

Jam nut

15

1. Check the electrical requirements. Be sure that you have

the correct electrical supply and the recommended earthing

method. See “Electrical Requirements.”

2. Check that all parts are now installed. If there is an extra part,

go back through the steps.

3. Check that you have all of your tools.

4. Dispose of/recycle all packaging materials.

5. Switch on power supply.

COMPLETE INSTALLATION

6. Check dryer operation. Using a full heat cycle, let the dryer

run for at least ve minutes. Dryer will stop when time is

used up.

NOTE: Dryer door must be closed for dryer to operate.

When door is open, dryer stops, but timer continues to run.

To restart dryer, close door and press cycle button.

WARNING

Electric Shock Hazard

This dryer must be earthed.

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electric shock.

16

REVERSING DOOR SWING (OPTIONAL)

Remove the Door Assembly

1. Place a towel or soft cloth on top of dryer or work space to

avoid scratching of the surface.

2. Remove 3 of the 4 screws that hold the door hinge on the

front panel of the dryer. Partially loosen the remaining screw

with keyhole opening and lift the door off the screw.

3. Lay the door assembly on a previously prepared at surface

with the inside (inner door assembly) facing up, and remove

6 Phillips-head screws to release outer door assembly from

inner door assembly.

NOTE: It is important that you remove only 6 indicated screws.

4. Lift the inner door assembly off outer door assembly.

5. Rotate outer door 180°.

Reverse Hinge

1. Use a small at-blade screwdriver to remove 2 plug strips

from the inner door. Slide the head of the screwdriver under

the plugs, without scratching inner door surface, and lift up

strip.

2. Remove the 4 screws that attach to inner door hinge.

17

REVERSING DOOR SWING (OPTIONAL)

3. Move hinge to other side. Reinstall 4 screws.

4. Reinstall plug strips on opposite side of the inner door.

5. Check for ngerprints on the glass. Clean if necessary.

Replace the Door Assembly

1. Place the inner door assembly inside the outer door

assembly.

2. Reassemble the inner and outer door assemblies with the

6 screws.

Reverse the Strike

1. Use a small at-blade screwdriver to remove plug strip from

the dryer door opening. Slide the head of the screwdriver

under the plugs, without scratching dryer surface, and lift

up strip.

2. Remove the strike using a Phillips screwdriver.

3. Insert strike on the opposite side.

Reinstall the Door

1. Partially insert the third screw from the top; then slide the

hinge onto this screw while hooking the hinge into the front

panel hole. Reattach door to dryer front panel with the

remaining three screws.

2. Check for ngerprints on the glass. Clean if necessary.

3. Close door and check that it latches securely.

18

MAINTENANCE INSTRUCTIONS

■ Clean lint screen before and after each cycle.

■ Removing accumulated lint:

From inside the dryer cabinet:

Lint should be removed every 2

years or more often, depending

on dryer usage. Cleaning should

be done by a qualied person.

From the exhaust vent:

Lint should be removed every 2

years, or more often, depending

on dryer usage.

If dryer does not operate, check the following:

■ Electrical supply is connected.

■ Circuit breaker is not tripped or house fuse is

not blown.

■ Door is closed. Listen closely to hear the door switch

activate.

■ Cycle selection button has been pushed rmly and display

shows cycle time.

If you need help, contact the dealer from whom you purchased

the appliance, or a Maytag designated service company.

When calling, please know the purchase date and the complete

model and serial number of your appliance. This information

will help us to better respond to your request.

IF YOU NEED ASSISTANCE

19

ELECTRONIC CONTROL SETUP INSTRUCTIONS

General User Information

“OUT OF ORDER” SHOWING IN DISPLAY –

This condition

indicates the dryer is inoperative. Diagnostic or failure code

will follow the scrolling message.

“0 MINUTES” SHOWING IN DISPLAY – This indicates the

cycle is complete and the dryer cannot be operated. Coins

dropped or debit inputs during this condition will be stored in

escrow but cannot be used until normal operation is restored

by opening and closing the door. If a door switch has failed,

it must be replaced before normal operation can be restored.

COLD START (Initial rst use) – Dryer is programmed at the

factory as follows:

45 minutes dry time for PN models; 5 minutes per coin for

PD models.

$1.50 dry price (xed cycle with top off – PD Models)

$0.00 dry price (xed cycle – PN Models)

WARM START (after power failure) – A few seconds after

power is restored, if a cycle was in progress at the time of the

power failure, “RESELECT CYCLE” will ash in the display.

This indicates a fabric setting button needs to be pressed

to restart dryer.

PRICING – After the door is opened and then closed following

the completion of a cycle, the display indicates the cycle price

(unless set for free operation). As coins are dropped or debit

inputs arrive, the display will change to lead the user through

the initiation of a cycle.

There are four (4) types of dryer pricing:

Fixed “Vend” Pricing

A dryer set up for “Fixed Cycle” operation can only accept

additional time accumulated by increments equal to the length

of a complete dry cycle. A maximum of 99 minutes may be

purchased; no additional credit is given with 99 minutes in

the display.

Accumulator Pricing

If the price is set to one coin 1, then accumulator pricing

is in effect. Cycle time can be purchased one coin at a time

(PD models) up to the maximum time of 99 minutes.

IMPORTANT

Electrostatic Discharge (ESD)

Sensitive Electronics

ESD problems are present everywhere. ESD may damage

or weaken the electronic control assembly. The new control

assembly may appear to work well after repair is nished,

but failure may occur at a later date due to ESD stress.

n Use an anti-static wrist strap. Connect wrist strap to green

earth connection point or unpainted metal in the appliance.

-OR-

Touch your nger repeatedly to a green earth connection

point or unpainted metal in the appliance.

n Before removing the part from its package, touch the

anti-static bag to a green ground connection point or

unpainted metal in the appliance.

n Avoid touching electronic parts or terminal contacts;

handle electronic control assembly by edges only.

n When repackaging failed electronic control assembly

in anti-static bag, observe above instructions.

Fixed Cycle With Top Off Pricing

A dryer set to offer “Top Off” capability will allow time to be

added to an existing dry cycle in increments equal to the

number of minutes of dry time per coin (coin 1), up to 99

minutes, regardless of the cost required to start the dryer. No

credit is given for coins or debit inputs entered when the control

is displaying 99 minutes.

PN Models set up as PR: In Enhanced Debit Mode, the top

off price can be set independently (see VALUE OF COIN 2),

and the top off time is calculated according to the following

equation:

Hundredth increment offset is not applied to top off purchases.

PN Models – The factory has preset the cycle price to zero.

When this happens, “SELECT CYCLE” will appear rather than

a cycle price. Any cycle started as a free cycle will automatically

terminate when the door is opened.

DEBIT CARD READY – This dryer has a control that is debit

card ready, but the dryer is not.

Display

After the dryer has been installed and plugged in, the display

will show “0 minutes.”

PD Models

Once the dryer has been plugged in and the dryer door opened

and closed, the display will show the vent price. PN models are

factory preset for free cycles; the display will ash “SELECT

CYCLE.”

PN Models

Control Set-up Procedures

IMPORTANT: Read all instructions before operating.

The fabric setting buttons along with the digital display

are used to set up the dryer controls. The display can contain

4 numbers and/or letters and a decimal point. These are used

to indicate the set-up codes and related code values available

for use in programming the dryer.

How to Use the Buttons to Program the Controls

1. The WHITES AND COLORS button is used to adjust the

values associated with set-up codes. Pressing the button

will change the value by increments. Rapid adjustment is

possible by holding down the button.

2. The PERM. PRESS button will advance the display

through the set-up codes. Pressing the button will advance

the display to the next available set-up code. Holding down

the PERM. PRESS button will automatically advance through

the set-up codes at a rate faster than 1 per second.

3. The DELICATES button is used to select or deselect options.

1.50

PRICE

top off time

full cycle length

top off price

full cycle price

=

20

ELECTRONIC CONTROL SETUP INSTRUCTIONS

The set-up code is indicated by the one or two left-hand

characters. The set-up code value is indicated by the two or

three right-hand characters.

NOTE: The rst line of each code indicates the factory default.

Code Explanation

6 06 REGULAR CYCLE PRICE

6 06 Represents the number of quarters (coin 1) needed to

start the dryer; may adjust from 0–39. (See b.xx set up

for VALUE OF COIN 1.) Advance from 0–39 by pressing

the WHITES AND COLORS button. Factory default of

6 x coin 1.

6 00 PN MODELS ONLY: Factory default of 6 00, or 0 coins.

• Press the PERM. PRESS button once to advance

to next code.

7 05 REGULAR DRY TIME

7 05 PD MODELS: Represents the number of minutes

per coin (coin 1).

Factory default of 5 minutes per coin.

Example: 6 coins x 5 minutes = 30 minutes.

By pressing the WHITES AND COLORS button,

value adjusts from 1–99 minutes.

7 45 PN MODELS: Represents the cycle length for free

cycles. Example: “7 45” = 45 minutes.

• Press the PERM. PRESS button once to advance

to next code.

8 00 TYPE OF DRYER PRICING

8 00 Fixed Cycle with Top Off. For detailed description,

see “General User Information.”

8 FC PN MODELS ONLY: Factory default of FC. Fixed

Cycle. For detailed description, see “General User

Information.” Use the DELICATES button to change

this selection.

• Press the PERM. PRESS button once to advance

to next code.

9 00 CYCLE COUNTER OPTION

This option is either NOT SELECTED “OFF”

or SELECTED “ON.”

9 00 Not Selected “OFF.”

9 0C Selected “ON” and not able to be deselected.

• Press the DELICATES button 3 consecutive times

to select “ON.” Once selected “ON,” it cannot be

deselected.

• Press the PERM. PRESS button once to advance

to next code.

If cycle counter (9 0C) is selected, the following is true:

1 00 Cycles in HUNDREDS 1 02 = 200

2 00 Cycles in ONES 2 25 = 25

TOTAL CYCLES = 225

This is “VIEW ONLY” and cannot be cleared.

• Press the PERM. PRESS button once to advance

to next code.

Start Operating Set-up

■ PD Models: Insert service door key, turn, and lift to remove

service door.

■ PN Models: Remove the AA1 jumper from the control board

(see procedure below) or use the Service Access Code

below. Once the debit card reader is installed (according

to the reader manufacturer’s instructions), the set-up mode

can be entered by inserting a manual set-up card (supplied

by the reader manufacturer) into the card slot. If manual

set-up card is not available, manual set-up mode cannot

be entered. However, diagnostic mode can be entered

by removing connector AA1 on the circuit board.

IMPORTANT: The console must not be opened unless

power is rst removed from the dryer. To access connector

AA1:

g

Unplug dryer or disconnect power.

g

Open console, disconnect plug on AA1, close console.

g

Plug in dryer or reconnect power.

n PN Models Equipped with Programming Switch: Insert

access panel key and turn counterclockwise.

n PN Models with Gen. 2 Debit Card Reader: Once a Gen.

2 debit card reader is installed (according to the reader

manufacturer’s instructions), the set-up mode can only be

entered by inserting a manual set-up card (supplied by the

reader manufacturer) into the card slot.

If manual set-up card is not available, only diagnostic mode

can be entered.

n Alternate method of entering Set-up Mode by entering

Service Access Code: This code can be entered to access

set-up mode without removing the console on dryers just

removed from the carton, or not yet programmed. The

Service Access Code only functions on dryers set up for 0

vend price without any Special Pricing setup, and the Coin/

Debit Option must be set to “J._d”. If the dryer is not in

failure mode, the door must be opened to proceed. Using

only the three bottom buttons (numbered 1, 2, and 3 from

left to right):

1. Press 2 for longer than 2 seconds but less than

10 seconds.

2. Press 1 and 3 simultaneously for 2 seconds. Display

shows S 3.

3. Press 1 and 2 simultaneously. Display shows S 4.

4. Press 2 and 3 simultaneously. Display shows S 5.

5. Press 2.

6. Wait at least 2 seconds, but not more than 15 seconds;

then press in succession: 3, 2, 1, 3.

The dryer is now in the set-up mode.

NOTE: This dryer is preset at the factory and does not require

any programming. However, if you want to change the settings,

follow the “Set-Up Codes” guide below. PD models require a

payment system or OPL kit to be installed prior to operation.

n

PD units are pre-set at the factory for xed cycle price with

top off.

n

PN units are pre-set for xed cycle operation so they can

be run without payment.

Set-Up Codes

■ The PERM. PRESS button will advance you from code to

code.

■ The WHITE AND COLORS button will change the code

value.

■

The DELICATES button will select or deselect options.

PN MODELS: The set-up codes are the same as for the PD

models except where noted.

La pagina sta caricando ...

Maytag MDE25PN Installation Instructions Manual

Questo manuale è adatto anche per

Maytag MDE25PN Installation Instructions Manual

in altre lingue

Documenti correlati

Altri documenti