Philips SC2000/00 Manuale utente

Register your product and get support at

www.philips.com/SatinLux

or call 00800-S-A-T-I-N-L-U-X (7-2-8-4-6-5-8-9)

SC2000

2

3

A

M

B

D

C

E

F

G

H

I

J

K

N

L

1

4

SC2000

ENGLISH 6

DEUTSCH 22

ESPAÑOL 40

FRANÇAIS

57

ITALIANO 74

NEDERLANDS 92

PORTUGUÊS

110

6

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet

from the support that Philips offers, register your product at www.philips.

com/satinlux.

Hair removal with light is one of the most effective methods to get

rid of unwanted body hair with longer lasting results. It is completely

different from current home hair removal methods and Philips has been

investigating this method together with leading dermatologists for almost

10 years. You can now use this innovative technology comfortably in the

privacy of your own home, whenever you want.

This appliance is intended for removing women’s body hair on areas below

the neck:

underarms

bikini area

legs

The appliance is not intended for:

persons with a too light body hair colour (light blond, red, grey or

white body hair) or a very dark skin. See chapter ‘Preparing for use’,

section ‘Setting the light intensity’.

For more information about the SatinLux, see www.philips.com/satinlux.

How photo-epilation works

Hair growth

Depending on age, metabolism and other factors, everyone’s hair grows

differently, but hair normally grows in three phases:

1 Anagen phase (growing phase)

The hair grows actively from the root. In this phase the concentration

of melanin is highest. Melanin is responsible for the pigmentation of the

hair. The more melanin there is in the root, the darker the hair is. Melanin

concentration is also the determining factor for the efcacy of this method.

Only hairs in the anagen phase are susceptible to treatment with light.

2 Catagen phase (degradation phase)

The hair growth stops and the root shrinks before the hair sheds.

3 Telogen phase (resting phase)

The old hair separates from the root and the new hair slowly pushes out

the old hair. The root remains at rest until the biological clock tells it to

become active again and grow a new hair (4). Hairs on an area of skin are

usually in different stages of the cycle of hair growth.

Working principle

The appliance removes hair by heating up the hair and root beneath the

skin. The melanin in the hair and hair root absorbs the released light pulses.

The darker the colour of the hair, the more heat can be produced. This

process stimulates the hair to go into the resting phase.

The hair now sheds naturally and the hair growth is inhibited.

Optimal hair removal cannot be obtained with a single session, since only

hairs in the anagen phase are susceptible to treatment with light. During

a treatment, hairs on the treated area are usually in different stages of the

cycle of hair growth.

To treat all hairs successfully and to prevent the hair root from becoming

active again, the treatments have to be repeated once every two weeks.

-

1 2 3 41 2 3 4

ENGLISH

An integrated optical lter makes sure no UV light reaches the skin and

therefore leaves it unharmed.

Benets

This appliance has the following advantages:

Professional IPL technology for home use

SatinLux uses a light-based technology called ‘Intense Pulsed Light’ (IPL). IPL

is also used in the professional beauty market for hair removal. SatinLux

now brings this innovative technology to the comfort of your home.

Effective hair regrowth prevention for everlasting smoothness

This method prevents hair from growing back for a long time and provides

a silky-smooth skin. Our studies have shown a signicant hair reduction

already after 2 treatments. Optimal results were generally achieved after

4 to 5 treatments. A reduction in hair density is visible from treatment to

treatment. How fast the effect becomes visible and how long the results

last varies from person to person. Repeat this treatment every two weeks

to achieve optimal results and to keep your skin smooth for ever.

Gentle treatment, even on sensitive body areas

SatinLux has been developed in close cooperation with leading

dermatologists for an effective and gentle treatment, even on the most

sensitive body areas.

Cordless operation for maximum freedom and exibility

Because the appliance runs on rechargeable batteries, it is portable and can

be used anywhere.

General description (Fig. 1)

A Light exit window with lter glass

B Removable window

C Metallic surface inside the removable window

D Safety system (safety ring with contact switches)

E Flash button

F Intensity lights (1- 5)

G % Intensity increase button

H ^ Intensity decrease button

I Charging light and battery low indication

J On/off button

K ’Ready to ash’ light

L Appliance socket

M Adapter

N Small plug

Also included: pouch and cleaning cloth

Important

Read this user manual carefully before you use the appliance and save it for

future reference.

ENGLISH 7

Danger

Water and electricity are a dangerous combination. Do not use

this appliance in wet surroundings (e.g. near a bath, a shower or a

swimming pool).

Keep the appliance and the adapter dry.

Warning

This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for

their safety.

Children should be supervised to ensure that they do not play with the

appliance.

Only use the appliance in combination with the adapter supplied.

Do not use the appliance if the adapter or the appliance itself is

damaged.

Do not use the appliance if the lter glass is broken.

If the adapter is damaged, always have it replaced with one of the

original type in order to avoid a hazard.

The adapter contains a transformer. Do not cut off the adapter to

replace it with another plug, as this causes a hazardous situation.

To prevent damage:

1 never cover the ventilation slots during use.

2 make sure nothing can obstruct the air ow through the ventilation

slots

3 never subject the appliance to heavy shocks and do not shake or drop

it.

If you take the appliance from a very cold environment to a very warm

environment, wait approximately 3 hours before you use it.

Never use or store the appliance in a dusty environment.

Never leave the appliance unattended when it is switched on. Always

switch off the appliance after use.

Do not expose the appliance to direct sunlight or UV light for a longer

time.

Caution

This appliance is only intended for removing women’s body hair. Do

not use it for any other purpose.

The appliance is only intended for removing human hair from areas

below the neck. Do not use it for any other body part.

This appliance is not designed for commercial or professional use.

If the appliance is used for commercial or professional purposes, if it

is used on other body parts than for which it is explicitly intended

or if it is used by persons explicitly excluded from use, the guarantee

becomes invalid and Philips refuses any liability for damage caused.

-

ENGLISH8

Your skin may become a little red and irritated after using the

appliance. This phenomenon is absolutely normal and quickly

disappears. If the irritation does not disappear within three days, we

advise you to consult a doctor.

Do not expose the appliance to temperatures lower than 15°C or

higher than 35°C during use.

The appliance is equipped with a built-in overheat protection. If the

appliance overheats, it does not ash. Do not switch off the appliance,

but let it cool down for approx. 15 minutes before you continue with

your treatment.

Always return the appliance to a service centre authorised by Philips

for examination or repair. Repair by unqualied people could cause an

extremely hazardous situation for the user.

Never use the appliance in any of the cases mentioned under

Contraindications.

Contraindications

Never use the appliance:

If you have a skin disease such as active skin cancer, if you have a history

of skin cancer or any other localised cancer in the areas to be treated,

if you have pre-cancerous lesions or multiple atypical moles in the areas

to be treated.

If you have epilepsy with ashlight sensitivity.

If you have a history of collagen disorder, including a history of keloid

scar formation or a history of poor wound healing.

If you have a history of vascular disorder, such as the presence of

varicose veins or vascular ectasia in the areas to be treated.

If your skin is sensitive to light and causes a rash or an allergic reaction.

If you are taking photosensitising agents or medications, check the

package insert of your medicine and never use the appliance if it is

stated that it can cause photo-allergic reactions, photo-toxic reactions

or if you have to avoid sun when taking this medicine.

If you have diabetes, lupus erythematodes, porphyria or congestive

heart disease.

On areas of your skin where you are currently being treated with or

have recently been treated with Alpha-Hydroxy Acids (AHAs), Beta-

Hydroxy Acids (BHAs), topical isotretinoin and azelaic acid.

If you have taken oral isotretinoin Accutane® or Roaccutane® in the

last six months.This treatment can make skin more susceptible to tears,

wounds and irritations.

If you have any bleeding disorder or take anticoagulation medications,

including heavy use of aspirin, in a manner which does not allow for a

minimum 1-week washout period prior to each treatment.

If you have infections, eczema, burns, inammation follicles, open

lacerations, abrasions, surgeries, herpes simplex, wounds or lesions and

haematomas in the areas to be treated.

If you have a history of immunosuppressive disease (including HIV

infection or AIDS) or when you take immunosuppressive medications.

When you are on painkillers, which reduce the sensitivity to heat.

If you are pregnant or breastfeeding.

On moles, freckles, large veins, darker pigmented areas, scars, skin

anomalies without consulting your doctor. This can result in a burn and

-

ENGLISH 9

change of colour, which makes it potentially harder to identify skin-

related diseases (e.g. skin cancer).

On nipples and mucous areas.

After intensive sunbathing and/or on sunburnt skin or if you use suntan

accelerators.

On warts, tattoo or permanent make-up. This can result in a burn and

change of colour.

If you use long-lasting deodorants. This can result in skin reactions.

Over or near anything articial like silicon implants, Implanon

contraceptive implants, pacemakers, subcutaneous injection ports

(insulin dispenser) or piercings.

Electromagnetic elds (EMF)

This Philips appliance complies with all standards regarding electromagnetic

elds (EMF). If handled properly and according to the instructions in this

user manual, the appliance is safe to use based on scientic evidence

available today.

Charging

Fully charge the batteries before you use the appliance for the rst time

and when the batteries are empty. Fully charging the batteries takes up to

4 hours.

Charge the appliance when the charging light lights up orange during use.

When the charging light goes on, the remaining capacity is at least 30

ashes.

Fully charged batteries provide at least 160 ashes at light intensity 5, which

amounts to approx. 15 minutes of cordless operation time. The actual

number of ashes varies, depending on the selected light intensity (see

‘Efcacy at different light intensities’ in chapter ‘Preparing for use’).

Fully charge the appliance every 3 to 4 months, even if you do not use the

appliance for a longer time.

1 Switch off the appliance.

2 Insert the small plug into the appliance and put the adapter in the

wall socket.

The charging light ashes green to indicate that the appliance is

charging.

When the batteries are fully charged, the charging light lights

up green continuously.

Caution: Never cover the appliance and adapter during charging.

Note: During charging, the appliance cannot be used.

Note: The adapter feels warm during charging. This is normal.

3 After charging, remove the adapter from the wall socket and pull the

small plug out of the appliance.

Preparing for use

For optimal results and highest efcacy, prepare the areas on which you

intend to use the appliance in the manner described below.

-

,

ENGLISH10

1 Shave the areas you intend to treat as long as you still experience

hair regrowth.

Never remove the hairs by means of wax, epilation, tweezers or

depilation cream. These methods counteract photo-epilation because

they remove hairs by the root. In these cases, the light cannot be

successfully absorbed by the root and the hairs will grow back again.

Note: Shaving is necessary to ensure that the light energy is channelled

to the hair root in the most efcient way. Furthermore, visible hairs in the

treatment area can be burnt by the light and can thus cause an unpleasant

smell. In general this is harmless, but it may be a bit painful when you use the

appliance.

2 Clean your skin and make sure it is entirely dry and free from grease

and oil (e.g. present in cosmetic products like deodorants, lotions,

perfumes, tanning creams and sunscreens).

Note: If shaving causes wounds or lesions, the skin may be more sensitive

as a result. In that case, the light treatment may be more perceptible and

sometimes even uncomfortable.

Note: Once the hairs stop growing back - which usually happens after a few

treatments - you no longer have to shave before you use the appliance.

Tip: If shaving causes skin irritation, you can also use a trimmer to trim the

hair as short as possible. In that case, the light treatment may be more

perceptible and sometimes even slightly uncomfortable.

Setting the light intensity

You have to adjust the light intensity to your skin and body hair colour and

to a level you nd comfortable.

The table with recommended light intensities below helps you to establish

the right light intensity.

1 Consult the table below to determine which light intensities are

most suitable for your skin and body hair colour and to check if this

method is suitable for you at all (if it is not, this is indicated with x in

the table).

Note: Persons with darker skin run a higher risk of skin irritation because

their skin absorbs more light. Therefore lower intensities are recommended for

persons with darker skin.

2 For each body area you want to treat, select a suitable intensity in

the recommended range that is as high as possible but does not

cause any discomfort on the skin.

The light intensity you use can feel warm or hot on the skin, but should

never feel uncomfortable.

Note: Before every treatment, check if the appliance is set to the right intensity.

ENGLISH 11

Recommended light intensities (1-5)

Skin colour &

characteristics :

White

(always

sunburn,

no

tanning)

Beige

(easy

sunburn,

minimal

tanning)

Light brown

(sometimes

sunburn,

good

tanning)

Mid

brown

(rarely

sunburn,

fast and

good

tanning)

Dark

brown

(rarely

sunburn,

very

good

tanning)

Black

(rarely

to never

sunburn,

very dark

tanning)

Body hair colour: white/

grey

x x x x x x

red x x x x x x

light

blond

x x x x x x

blond 4/5 4/5 4/5 3/4/5 1/2/3/4 x

dark

blond/

light

brown

4/5 4/5 4/5 3/4/5 1/2/3/4 x

brown 4/5 4/5 4/5 3/4/5 1/2/3/4 x

dark

brown

4/5 4/5 4/5 3/4/5 1/2/3/4 x

black 4/5 4/5 4/5 3/4/5 1/2/3/4 x

x means that the appliance is not suitable for use.

Note: The appliance is not suitable for persons with very dark to black skin

because of the higher risk of skin irritations.

Note: The appliance is not suitable for persons with light blond, red, grey and

white body hair because the low melanin concentration in the hair results in

very poor hair removal efcacy.

Note: At higher light intensities the method is not only more efcacious, but it is

also more perceptible.

Efcacy at different light intensities

Light intensity Efcacy Number of ashes

5 ***** 160

4 **** 190

3 *** 250

2 ** 350

1 * 520

* indicates the level of efcacy

ENGLISH12

Note: This table shows the number of ashes the appliance can give at each

light intensity and the corresponding expected efcacy. Please use the intensity

appropriate for your skin colour and body hair colour.

Using the appliance

The light intensity you use can feel warm or hot on the skin, but should

never feel uncomfortable.

This appliance is only intended for removing women’s body hair on areas

below the neck: underarms, bikini area and legs.

Note: Shave the area you intend to treat before you use the appliance (see

chapter ‘Preparing for use’).

Tip: The best time for treatment is before you go to bed at night.This

diminishes any skin reaction that may occur overnight.

1 Press the on/off button to switch on the appliance.

Intensity light 1 goes on automatically to indicate that the appliance

is switched on at default intensity 1.

Note: You can switch off the appliance any time by pressing the on/off button

again.

Note: It is normal that the appliance becomes warm during use.

2 Press the % button to increase the intensity. To lower the intensity,

press the ^ button.

Every time you press the button, the corresponding intensity

light starts to ash. This takes a few seconds.

3 Place the appliance perpendicularly on the skin so that the

removable window and the safety ring are in contact with the skin.

Tip: When you use the appliance for the rst time, try it out, for instance on

your hip, to get accustomed to the light-based method. Start with the lowest

recommended intensity and increase it until you have reached the highest

recommended intensity. This test tells you how sensitive your skin is to light.

Check if your skin shows any reactions 20 minutes after the test. If it does, use

a lower recommended intensity for the areas to be treated.

,

ENGLISH 13

4 Press the safety ring fully onto the skin with slight pressure.

Note: The safety ring has contact switches that together are the safety system

of the appliance. This safety ring prevents unintentional ashing without skin

contact.

When all contact switches of the safety ring have been pushed

into the appliance, the ‘ready to ash’ light on the back of the

appliance goes on. This may take a few seconds. When the ‘ready to

ash’ light is on, the appliance is ready to release a ash.

Tip: For easier use, stretch the skin you want to treat. On areas with softer skin,

you may need to exert more pressure on the appliance to push in all contact

switches.

5 Press the ash button to release a ash. After the appliance has

ashed once, release the ash button.

6 For the next ash, repeat steps 3, 4 and 5. This can take a few

seconds.

Never ash the same area twice without lifting the appliance off the skin.

This prevents excessive heating and possible burning of the skin.

7 To avoid untreated areas, always make sure there is some overlap

with the previously treated area when you place the appliance on the

skin.The effective light only comes out of the light exit window. Make

sure the ashes are produced close to each other.

8 Switch off the appliance after you have nished the treatment.

Note: Avoid looking straight into the light coming out of the window when the

appliance is switched on.

Note: The visible light produced by the appliance is the reection of the ash

on the skin and is harmless to your eyes. It is not necessary to wear goggles

during use.

Guidelines for treatment

Recommended number of ashes and treatment time

Area Approx. number of ashes Approx. treatment time

Underarms 25 per underarm 3 minutes per underarm

Bikini line 25 per side 3 minutes per side

Entire bikini area 90 for entire area 10 minutes

One lower leg 160-190 15 minutes

,

ENGLISH14

Area Approx. number of ashes Approx. treatment time

One full leg 320-380 30 minutes

Note: Fully charged batteries offer at least 160 ashes at intensity 5, which

amounts to a cordless operating time of approx. 15 minutes.

How to achieve optimal results

Optimal results cannot be obtained with a single session, since only hairs

in the anagen phase are susceptible to treatment with light. During a

treatment, hairs on a treated area are usually in different stages of the cycle

of hair growth. To treat all hairs successfully and to prevent that the hair

root becomes active again, you have to repeat the treatment every 2

weeks. It is recommended to adhere to this frequency. Better results are

not expected if you increase or decrease the treatment frequency. Clinical

trials have shown that this is the optimal frequency of use.

After treatment

After treatment it may happen that:

Your skin shows slight redness and/or prickles, tingles or feels warm.

This reaction is harmless and disappears quickly.

A skin reaction similar to sunburn may occur on the treated area for a

short while.

Your skin may appear to be dry, as the combination of shaving and light

treatment may cause dry skin.

Some hairs grow back although you use the appliance frequently.

This happens because hairs are in different stages of the cycle of hair

growth during treatment. The hairs that grow back tend to be softer

and thinner.

It is recommended to

:

Consult your doctor if skin irritation does not disappear within three

days (see chapter ‘Important’, section ‘Caution’).

Wait with the next treatment until skin irritation has disappeared

completely. Perhaps you have used an intensity that was too high for

you. Use a lower intensity the next time.

Do not take an intensive sunbath or suntan without proper protection

immediately after a treatment. If you want to go sunbathing after a

treatment, apply a sun blocker to the treated areas.

Avoid swimming in chlorinated water for 48 hours after treatment.The

chlorine in the water can cause itchiness.

Avoid applying any cosmetic substances to the treated areas

immediately after treatment.

Cleaning and maintenance

Never clean the appliance or any of its parts under the tap or in the

dishwasher.

Never use scouring pads, abrasive cleaning agents or aggressive liquids

such as petrol or acetone to clean the appliance.

Never scratch the lter glass or the metallic surface inside the

removable window.

-

ENGLISH 15

Note: Make sure that the contact switches of the safety ring do not get

jammed with dirt.

Note: Stop using the appliance when it is no longer possible to clean the lter

glass or the removable window.

To ensure optimal results and a long life for the appliance, clean the

appliance after each treatment.

1 Switch off the appliance, unplug it and let it cool down.

Note: The lter glass becomes hot during use. Make sure it has cooled down

before you clean it.

2 To remove the removable window, put your ngers in the recesses

on the housing of the appliance and pull the removable window off

the appliance.

3 Use the dry, soft cloth supplied with the appliance to clean the

following parts:

the surface of the lter glass

the outside surface of the removable window

the metallic frame inside the removable window

the housing of the appliance (if necessary)

Note: If necessary, wet the cloth with some drops of water.

Storage

1

Switch off the appliance, unplug it and let it cool down.

2 Clean the appliance before you store it.

3 Put the appliance in the pouch supplied.

4 Store the appliance in a dry place at a temperature between 0°C and

60°C.

Environment

Do not throw away the appliance with the normal household waste

at the end of its life, but hand it in at an ofcial collection point for

recycling. By doing this, you help to preserve the environment.

The built-in rechargeable batteries contain substances that may pollute

the environment. Always remove the batteries before you discard and

hand in the appliance at an ofcial collection point. Dispose of the

batteries at an ofcial collection point for batteries. If you have trouble

removing the batteries, you can also take the appliance to a Philips

service centre. The staff of this centre will remove the batteries for you

and will dispose of them in an environmentally safe way.

Removing the rechargeable batteries

Only remove the rechargeable batteries if they are completely empty.

1 Insert an awl or another pointed tool into the appliance tool and pry

the bottom cap off the handle.

-

ENGLISH16

2 Undo the two screws.

3 Remove the bottom part of the handle and cut the two wires that

connect the bottom part to the appliance.

4 Pull the battery connectors off the battery terminals.

5 Shake the rechargeable batteries out of the appliance.

6 Cut the two wires that connect the rechargeable batteries to the

appliance.

ENGLISH 17

Guarantee and service

If you need service or information or if you have a problem, please visit

the Philips website at www.philips.com/satinlux or call 00800-SATINLUX

(72846589).

Replacement parts

The following replacement parts are available:

Removable window

Adapter

Pouch

Technical specications

Model SC2000

Rated voltage 100V-240V

Rated frequency 50Hz-60Hz

Rated input 7.5W

Protection against electric shock Class II Q

Protection rating IP 30 (EN 60529)

Operating conditions Temperature: +15° to +35°C

Relative humidity: 25% to 75%

Storage conditions Temperature: 0° to +60°C

Relative humidity: 5% to 95%

Intense pulsed light lamp Spectrum: >570nm

Lithium ion battery 2 x 3.7 Volt

1100 mAh

Troubleshooting

This chapter summarises the most common problems you could

encounter with the appliance. If you are unable to solve the problem with

the information below, contact the Consumer Care Centre in your country.

See the telephone number on the back of the user manual or visit www.

philips.com/satinlux for further information.

Problem Possible cause Solution

The appliance does not

work.

The rechargeable

batteries are empty.

Charge the appliance (see chapter ‘Charging’).

The appliance is

broken.

Contact the Consumer Care Centre in your

country, your Philips dealer or a Philips service

centre.

The appliance suddenly

switches off.

The rechargeable

batteries are empty.

Charge the appliance (see chapter ‘Charging’).

-

ENGLISH18

Problem Possible cause Solution

The adapter becomes

warm during charging.

This is normal. No action required.

The charging light does

not go on when I put

the small plug in the

appliance socket.

You have not put the

adapter in the wall

socket.

Insert the small plug into the appliance socket and

put the adapter in the wall socket.

Connect another appliance to the wall socket to

check if the wall socket is live.

If the appliance still does not charge, contact the

Consumer Care Centre in your country, your

Philips dealer or a Philips service centre.

The adapter is not

inserted properly into

the wall socket and/or

the small plug is not

inserted properly into

the appliance socket.

Make sure the adapter is inserted properly into

the wall socket and/or the small plug is inserted

properly into the appliance socket.

The appliance is

broken.

Contact the Consumer Care Centre in your

country, your Philips dealer or a Philips service

centre.

I have switched on the

appliance but I cannot

increase or decrease the

light intensity.

The appliance has to

be reset.

To reset the appliance, switch off the appliance

and then switch it on again. If you still cannot

adjust the light intensity, contact the Consumer

Care Centre in your country, your Philips dealer or

a Philips service centre.

The ‘ready to ash’ light

does not go on when I

place the appliance on

the skin.

You have not put the

removable window

with safety ring

properly on the skin.

Place the appliance perpendicularly onto the skin

in such a way that all contact switches touch the

skin. Then check if the ‘ready to ash’ light is on

and press the ash button.

If this does not work, place the appliance on a

part of your body where it is easy to establish full

skin contact, for example on your lower arm.Then

check if the ‘ready to ash’ light works. If the ‘ready

to ash’ light still does not go on when you place

the appliance on the skin, contact the Consumer

Care Centre in your country, your Philips dealer or

a Philips service centre.

The safety ring is dirty. Clean the safety ring carefully. If you are unable

to clean the safety ring properly, contact the

Consumer Care Centre in your country, your

Philips dealer or a Philips service centre to replace

the ash screen.

ENGLISH 19

Problem Possible cause Solution

The ‘ready to ash’ light

does not go on when

I place the removable

window on my skin, but

the cooling fan works.

The overheat

protection has been

activated.

When the overheat protection has been activated,

the fan still works. Do not switch off the appliance

and let it cool down for approx. 15 minutes before

you continue to use it. If the ‘ready to ash’ light

still does not go on when you place the appliance

on the skin, contact the Consumer Care Centre

in your country, your Philips dealer or a Philips

service centre.

The ‘ready to ash’

light is green but

the appliance does

not produce a ash

when I press the ash

button.

The appliance needs to

be reset.

To reset the appliance, switch off the appliance

and switch it on again. If the ‘ready to ash’ light

is green but the appliance still does not produce

a ash when you press the ash button, contact

the Consumer Care Centre in your country, your

Philips dealer or a Philips service centre.

The appliance becomes

warm during use.

This is normal. No action required.

The appliance does not

show light intensity 1

when I switch it on.

The appliance needs to

be reset.

To reset the appliance, switch it off and on again.

If the appliance still does not show light intensity

1, contact your Customer Care Centre, your

Philips dealer or a Philips Service Centre.

The appliance produces

a strange smell.

The removable

window is dirty.

Clean the removable window carefully. If you

are unable to clean the removable window

properly, contact the Consumer Care Centre

in your country, your Philips dealer or a Philips

service centre to replace the removable window.

You have not shaved

the area to be treated

properly.

If there are hairs on the area to be treated, these

hairs may get burnt when you use the appliance.

As a result, you notice a strange smell. Shave the

area to be treated properly before you use the

appliance.

The treatment is more

perceptible than usual.

You used a too high

light intensity.

Check if you have selected the right light intensity.

If necessary, select a lower light intensity.

You did not shave the

areas to be treated.

Always shave the areas to be treated before you

use the appliance.

The appliance is

defective.

Contact the Consumer Care Centre in your

country, your Philips dealer or a Philips service

centre.

You stored the

appliance in a dusty

environment.

The strange smell disappears after a few ashes.

The lter glass in the

light exit window is

broken.

If the lter glass in the light exit window is broken,

do not use the appliance anymore. Contact the

Consumer Care Centre in your country, your

Philips dealer or a Philips service centre.

ENGLISH20

La pagina sta caricando ...

Philips SC2000/00 Manuale utente

Questo manuale è adatto anche per

Philips SC2000/00 Manuale utente

in altre lingue

Documenti correlati