RF SOLUTIONS PRO-EZTEXT26 Manuale utente

Marca: RF SOLUTIONS

Modello: PRO-EZTEXT26

Tipo: Manuale utente

EZTEXT-DIN

DS-EZTEXT-DIN-3

Features

• Two way remote control Via SMS Text

• Easy to install and configure using only SMS

text messages

• Modular Expandable System

• 2-18 digital inputs (volt free)

• 2-18 Relay Changeover contacts rated

240Vac 5A

• Text on Power Restore

• Integral Antenna supplied (External Option)

• Optional Temperature Sensor

• User can set inputs and outputs names

• Worldwide quad-band GSM.

• O2 SIM Card Included

Applications

• Plant Maintenance

• Warnings / Alarms/ Reset

• Irrigation Systems

• Security Systems

• Heating Control

• World-wide Telemetry Signals

Description

A GSM Remote Control System operated by SMS text message. Available as DIN Rail

Modules or a ready made System within an IP56 enclosure Mains power supply and

bundled SIM card ready to go.

The user can switch the relay changeover contacts by sending a simple or custom

text of their choice.

EZTEXT will send an SMS text to up to five numbers on activation of one of its inputs

or temperature set points.

The user can give custom names to Inputs/outputs and create Custom messages.

Setup is easy with a few simple SMS Text Commands.

GSM Remote Control Systems

Ordering Information

PART No Description

EZTEXT-DIN DIN Rail SMS Control System

PRO-EZTEXT26 2 IP 6 OP Channel Remote Control System

EZTEXT-DIN

PRO-EZTEXT-26

EZTEXT-DIN

DS-EZTEXT-DIN-3

Safety Information

Carefully read the following safety information before proceeding with installation, operation, or

maintenance of RF Solutions product. Failure to follow these warnings could result in death or serious

injury

• This radio system must not be used in areas where there is a risk of explosion.

• Only qualified personnel should be permitted to access the transmitter and operate the equipment.

• Always follow operating information as well as all applicable safety procedures and requirements.

• You must satisfy the age requirements in your country for operating the equipment.

• Store in a safe place.

• Keep a clear view of the work area at all time before using, check it is safe to do so

Before maintenance intervention on any remote controlled equipment

• Do not open the receiver enclosure unless you are qualified.

• Disconnect all electrical power from the equipment.

• Check the enclosure and cable for damage regularly, do not use if there is evidence of damage

Electrical Safety

ISOLATE the mains electricity supply before removing the cover and observe any relevant safety

information.

• Maintenance to the product that involves removal of the cover should only be carried out by a

competent person or qualified electrician.

• Ensure adequate protection on the Load circuit

• Refer to Product Datasheet for MAX operating Load.

• Product must be installed in accordance with the local country electrical regulations.

• A current limiting supply must be used in accordance with the datasheet

EZTEXT-DIN

DS-EZTEXT-DIN-3

Information sur la sécurité

Avertissements de sécurité

• ISOLER l'alimentation électrique avant de retirer le couvercle et observer toutes les précautions de

sécurité pertinentes.

• L'entretien du produit qui implique le retrait du couvercle ne doit être effectué que par une personne

compétente ou un électricien qualifié.

• La valeur nominale du fusible F2 est de 4A (T) 250 H (céramique). Remplacez le fusible par le même

type et la même valeur nominale.

• La sortie relais est évaluée à 10A en crête et 5A en constante.

• Le produit doit être connecté à une alimentation à fusible ou à une prise de connexion appropriée ré-

pondant aux exigences du pays d'installation.

Lisez attentivement les informations de sécurité suivantes avant de procéder à l'installation, l'utilisation

ou la maintenance du produit RF Solutions. Le non-respect de ces avertissements peut entraîner la mort

ou des blessures graves

• Ce système radio ne doit pas être utilisé dans des zones présentant un risque d'explosion

• Seul le personnel qualifié doit être autorisé à accéder à l'émetteur et à utiliser l'équipement.

• Suivez toujours les instructions d'utilisation ainsi que toutes les procédures et exigences de sécurité

applicables.

• Vous devez satisfaire aux exigences d'âge dans votre pays pour utiliser l'équipement

• Il est strictement interdit d'utiliser l'équipement sous l'influence de drogues, d'alcool et/ou de médica-

ments.

• Conserver dans un endroit sûr.

• Gardez une vue dégagée sur la zone de travail à tout moment

Avant intervention de maintenance sur tout équipement télécommandé

• N'ouvrez pas le boîtier du récepteur à moins d'être qualifié

• Coupez toujours l'alimentation électrique de l'équipement.

• Vérifiez régulièrement que le boîtier et le câble ne sont pas endommagés, ne les utilisez pas s'il y a des

preuves de dommages

EZTEXT-DIN

DS-EZTEXT-DIN-3

Veiligheidsinformatie

Lees de volgende veiligheidsinformatie zorgvuldig door voordat u doorgaat met de installatie, bediening of

het onderhoud van het RF Solutions-product. Het niet opvolgen van deze waarschuwingen kan de dood of

ernstig letsel tot gevolg hebben

• Dit radiosysteem mag niet worden gebruikt in gebieden waar explosiegevaar bestaat.

• Alleen gekwalificeerd personeel mag toegang krijgen tot de zender en de apparatuur bedienen.

• Volg altijd de bedieningsinformatie en alle toepasselijke veiligheidsprocedures en -vereisten.

• U moet voldoen aan de leeftijdsvereisten in uw land voor het gebruik van de apparatuur.

• Bewaar op een veilige plaats.

• Houd te allen tijde een duidelijk zicht op het werkgebied voordat u het gebruikt, controleer of het

veilig is om dit te doen

Vóór onderhoudsinterventie op op afstand bediende apparatuur

• Open de behuizing van de ontvanger niet tenzij u hiervoor gekwalificeerd bent.

• Koppel alle elektrische stroom van de apparatuur los.

• Controleer de behuizing en kabel regelmatig op beschadigingen, niet gebruiken als er tekenen van

schade zijn

Electrische veiligheid

ISOLEER de netvoeding voordat u het deksel verwijdert en neem alle relevante veiligheidsinformatie in

acht.

• Onderhoud aan het product waarbij de afdekking moet worden verwijderd, mag alleen worden uitge-

voerd door een competent persoon of een gekwalificeerde elektricien.

• Zorg voor voldoende bescherming op het belastingscircuit

• Raadpleeg het productgegevensblad voor de MAX bedrijfsbelasting.

• Het product moet worden geïnstalleerd in overeenstemming met de plaatselijke elektriciteitsvoor-

schriften van het land.

• Er moet een stroombegrenzende voeding worden gebruikt in overeenstemming met de datasheet

EZTEXT-DIN

DS-EZTEXT-DIN-3

Sicherheitsinformation

Lesen Sie die folgenden Sicherheitsinformationen sorgfältig durch, bevor Sie mit der Installation, dem Be-

trieb oder der Wartung des RF Solutions-Produkts fortfahren. Die Nichtbeachtung dieser Warnungen kann

zum Tod oder zu schweren Verletzungen führen.

• Dieses Funksystem darf nicht in explosionsgefährdeten Bereichen eingesetzt werden.

• Nur qualifiziertem Personal sollte der Zugang zum Messumformer und die Bedienung des Geräts ges-

tattet werden.

• Befolgen Sie immer die Betriebsinformationen sowie alle geltenden Sicherheitsverfahren und -

anforderungen.

• Für den Betrieb des Geräts müssen Sie die Altersanforderungen Ihres Landes erfüllen.

• An einem sicheren Ort aufbewahren.

• Behalten Sie vor der Verwendung jederzeit freie Sicht auf den Arbeitsbereich und prüfen Sie, ob dies

sicher ist

Vor Wartungsarbeiten an ferngesteuerten Geräten

• Öffnen Sie das Empfängergehäuse nur, wenn Sie dafür qualifiziert sind.

• Trennen Sie die gesamte Stromversorgung vom Gerät.

• Gehäuse und Kabel regelmäßig auf Beschädigungen prüfen, bei Anzeichen von Beschädigungen nicht

verwenden.

Elektrische Sicherheit

TRENNEN Sie die Netzstromversorgung, bevor Sie die Abdeckung entfernen und beachten Sie alle rele-

vanten Sicherheitshinweise.

• Die Wartung des Produkts, bei der die Abdeckung entfernt wird, darf nur von einer sachkundigen Person

oder einem qualifizierten Elektriker durchgeführt werden.

• Sorgen Sie für einen ausreichenden Schutz des Lastkreises

• Siehe Produktdatenblatt für MAX Betriebslast.

• Das Produkt muss in Übereinstimmung mit den örtlichen Elektrovorschriften des Landes installiert

werden.

• Es muss eine Strombegrenzungsversorgung gemäß Datenblatt verwendet warden.

EZTEXT-DIN

DS-EZTEXT-DIN-3

Información de seguridad

Lea atentamente la siguiente información de seguridad antes de continuar con la instalación, operación o

mantenimiento del producto de RF Solutions. El incumplimiento de estas advertencias podría provocar la

muerte o lesiones graves.

• Este sistema de radio no debe utilizarse en áreas donde exista riesgo de explosión.

• Solo se debe permitir el acceso al transmisor y operar el equipo a personal calificado.

• Siga siempre la información de funcionamiento, así como todos los procedimientos y requisitos de

seguridad aplicables.

• Debe cumplir con los requisitos de edad en su país para operar el equipo.

• Almacenar en un lugar seguro.

• Mantenga una vista clara del área de trabajo en todo momento antes de usar, verifique que sea se-

guro hacerlo

Antes de la intervención de mantenimiento en cualquier equipo controlado a distancia

• No abra la caja del receptor a menos que esté calificado.

• Desconecte toda la energía eléctrica del equipo.

• Compruebe la carcasa y el cable en busca de daños con regularidad, no los utilice si hay evidencia de

daños

Seguridad ELECTRICA

AISLE el suministro eléctrico de la red antes de quitar la tapa y observe cualquier información de seguri-

dad relevante.

• El mantenimiento del producto que implica la extracción de la cubierta solo debe ser realizado por

una persona competente o un electricista calificado.

• Asegurar una protección adecuada en el circuito de carga.

• Consulte la hoja de datos del producto para conocer la carga operativa MÁXIMA.

• El producto debe instalarse de acuerdo con las normativas eléctricas locales del país.

• Se debe utilizar un suministro de limitación de corriente de acuerdo con la hoja de datos

EZTEXT-DIN

DS-EZTEXT-DIN-3

Informazioni sulla sicurezza

Leggere attentamente le seguenti informazioni sulla sicurezza prima di procedere con l'installazione, il

funzionamento o la manutenzione del prodotto RF Solutions. La mancata osservanza di queste avvertenze

può provocare morte o lesioni gravi

• Questo sistema radio non deve essere utilizzato in aree a rischio di esplosione.

• L'accesso al trasmettitore e l'utilizzo dell'apparecchiatura deve essere consentito solo a personale

qualificato.

• Seguire sempre le informazioni operative, nonché tutte le procedure e i requisiti di sicurezza applica-

bili.

• È necessario soddisfare i requisiti di età nel proprio paese per l'utilizzo dell'apparecchiatura.

• Conservare in un luogo sicuro.

• Mantenere sempre una visione chiara dell'area di lavoro prima dell'uso, controllare che sia sicuro farlo

Prima dell'intervento di manutenzione su qualsiasi apparecchiatura telecomandata

• Non aprire l'involucro del ricevitore se non si è qualificati.

• Scollegare tutta l'alimentazione elettrica dall'apparecchiatura.

• Controllare regolarmente la custodia e il cavo per verificare che non siano danneggiati, non utilizzare

se vi sono segni di danneggiamento

Sicurezza elettrica

ISOLARE l'alimentazione di rete prima di rimuovere il coperchio e osservare tutte le informazioni di

sicurezza pertinenti.

• La manutenzione del prodotto che comporta la rimozione del coperchio deve essere eseguita solo da

una persona competente o da un elettricista qualificato.

• Garantire un'adeguata protezione sul circuito di carico

• Fare riferimento alla scheda tecnica del prodotto per il carico operativo MAX.

• Il prodotto deve essere installato in conformità con le normative elettriche locali del paese.

• È necessario utilizzare un'alimentazione con limitazione di corrente in conformità con la scheda tec-

nica

PRO-EZTEXT-26

DS-EZTEXT-DIN-3

Description

Supplied as a self contained two way Remote Control System which provides two

‘no volt’ switch detect inputs and 6 changeover relay contacts as outputs.

The system comes supplied in an IP56 Enclosure with integral 12V power supply.

Containing industrial standard ‘DIN Rail’ modules.

Ready to Go System 2 I/P,’s 6 O/P’s

110/230VAC

Power

Supply

9-32V

ac or dc

Power

Digital

Input 1

Digital

Input 2 Output 1Output 2

2 Input

6 Output

NO COM NC NO COM NC

Reset 20

GSM

SIM card

Output 1Output 2Output 3Output 4

Power in

- +

NO COM NC

Address

EZTEXT-DIN 725-OP

Address

link 1

fitted

PSU

Common

Normally Open

Normally Closed

FUSE

Output 1 -4

Features

• 110-230Vac Power Supply Fused 5A

• 2 No Volt Switch inputs

• 6 Outputs Relay Changeover Contacts

240Vac 5A

• Enclosure IP56

• No PC required.

• SIM Card Bundled

• Dims 315 x 235 x 130mm

EZTEXT-DIN

DS-EZTEXT-DIN-3

4 x Inputs Module

• 4 x Additional No-Volt Inputs

• Plug ‘n’ Play using ribbon cable supplied

• Up to 4 additional Input Modules can be

Daisy Chained to provide 16 additional

Inputs

• Inputs are opto-isolated

Part Number Description

725-OP 4 Output Add-on Module

4 x Relay Output Module

• 4 x Relay Changeover Contacts

• Connecting ribbon cable supplied

• Up to four Output Modules can be Daisy

Chained to provide an additional 16 Outputs.

• Up to 4 x 725-OP can be Daisy Chained to

provide 18 outputs.

• Provides a simple extension to the number

of Inputs

Part Number Description

725-IP 4 input Add-on Module

Additional Input and Output Modules

Temperature Measurement Probe Cable

Using the cable adaptor CBA-EZTEMP provides a 1metre plug in cable with

temperature probe.

This enables the EZTEXT temperature monitor temperature and automatically send

notification of high and low user selectable trigger level.

Part Number Description

CBA-EZTEMP2 Temperature sensor cable

The Add-on Modules simply plug into the EZTEXT-DIN Ribbon Connector socket.

Once connected the EZTEXT automatically recognizes them and the additional

inputs and outputs become available to use.

EZTEXT-DIN

DS-EZTEXT-DIN-3

Optional External Antenna

Using an external antenna can provide a better signal reception than the on-board

antenna. Using Cable adaptor CBA-UFLSMA provides a panel mounted SMA

connector for external antenna connection.

To connect, carefully unplug the existing antenna UFL and push on the

CBA-UFLSMA UFL connector.

ANT-GSM5WM

A compact PCB Antenna for GSM Cellular applications where

high performance is required from a small size. Using the

ANT-GSMQB will give optimum range and reliability to your

application.

ANT-GSMPUKS-IP67

A compact Antenna for GSM applications where high

performance is required from a small size. The

antenna includes a Low Noise Amplifier and is

housed in a rugged low profile UV resistant case,

this antenna is compact and resistant to

Vandalism.

CBA-UFLSMA

Connect to

On-board UFL

connector

Alternative Antenna

We offer an extensive range of GSM antenna in many shapes and sizes please see

our Website or contact our Sales Dept with your requirements and we will try to

help.

Part Number Description

CBA-UFLSMA Cable assembly for external antenna

Part Number Description

ANT-GSM5WM +5dBm Gain antenna with wall mount

Part Number Description

ANT-GSMPUK-SMA +3dBm Gain antenna Rugged PUCK

EZTEXT-DIN

DS-EZTEXT-DIN-3

Using EZTEMPR2 Thermocouple

Attach the Thermocouple cable to the Connector marked “SENSE”

This is now ready to use:

Notes:

1. Temperatures are measured to 1 Decimal point

2. Temperature Triggers can be set to whole number values only

3. A hysteresis of –2oC is built into the EZTEXT

Example 1

SET TEMP MAX is set to +30oC

As the actual temperature measured increases, EZTEXT will trigger ‘over

Temperature’ at 30.1oC

As the actual temperature measured decreases EZTEXT will trigger at 27.9oC

Example 2

SET TEMP MIN is set to +10oC

As the actual temperature measured decreases, EZTEXT will trigger ‘under

Temperature’ at 9.9oC

As the actual temperature measured increases EZTEXT will trigger ‘Good’ at

12.1oC

Using Additional Input / Output Modules

Input and Output modules can be added in any order by connecting with the

Ribbon cables supplied.

On initial Powerup EZTEXT automatically interrogates and configures

additional modules. (all LEDS Flash). After approx. 60seconds the LEDs stop

flashing to indicate the module is ready to use

Notes:

1. Any combinations of 725-IP and 725-OP modules can be added, the Maximum is four, 725-IP

Modules and four 725-OP modules in the ‘Daisy Chan’ link (8 modules in total)

2. When using 725-IP / OP modules there are some limitations (compared with the two input and

outputs on the ETEXT-DIN)

Power

Supply

9-32V

ac or dc

Power

Digital

Input 1

Digital

Input 2

Relay

Output 1

Relay

Output 2

Power

Input 1 Input 2 Input 3 Input 4

Address Power Power

Input 1 Input 2 Input 3 Input 4

Address Power

3 4 5 6 7 8 910

NO COM NC NO COM NC

Reset 20

GSM10

SIM card

EZTEXT-DIN 725-IP 725-IP

EZTEXT-DIN

DS-EZTEXT-DIN-3

725-OP Additional 4 Outputs Module

Output 1

Ribbon

Cable

Connector

Ribbon

Cable

Connector

Changeover Relay Contact

Outputs

Output 2 Output 3 Output 4

NO COM NCNO COM NC

Address

ADDRESS LINKS

Place Shorting Cap over

Links to set address

(Fig shows Address position

Power

Supply

9-32V

ac or dc

Power

Digital

Input 1

Digital

Input 2

Relay

Output 1

Relay

Output 2

Input 1 2

Output

NO COM NC NO COM NC

Reset 20

GSM10

SIM card

Output 1 Output 2 Output 3 Output 4 Power in

- +

NO COM NCNO COM NC

Address

Output 1 Output 2 Output 3 Output 4 Power in

- +

NO COM NCNO COM NC

Address

EZTEXT-DIN 725-OP 725-OP

65 8

710

• Each 725-OP module must have a

different address Link setting to other

725-OP modules

(For the application shown address

Link 2 is fitted this sets the outputs to

be numbers 7-10)

• Each Relay Changeover contacts

Output can only be switched “On” or

“Off”.

• Functions such as time delays cannot

be used.

• A single telephone OPNUM number

applies per output

Example: the number allocated to an

output board that you would use to send

a text message to activate an output.

EZTEXT-DIN

DS-EZTEXT-DIN-3

Insert SIM Card

Please note:

• Insert NANO SIM Card before applying power (standard 3 Volt SIM only).

• The message memory of the SIM card should be clear before it is fitted.

• Ensure that the SIM card has not been PIN code protected!

• Beware of Pay-as-you-go SIM which require regular top-up to remain active.

• It is recommended to bar Incoming voice calls to the SIM card to avoid error

messages being sent back to the user. This can be achieved with the service

provider.

The SIM card should be inserted into EZTEXT-DIN before applying power

• RF Solutions recommends O2 and Vodaphone SIM card and has carried out

extensive testing using the SIM cards we have for these two networks.

• No guarantee can be given for the operation of this product with any network

except those that have been tested by RF Solutions.

The EZTEXT-DIN unit can be powered from 12 to 24Vdc

Connect Inputs/Outputs and Power Connections

Supply

Terminals

1 2

Inputs

1 2

Outputs

Module ADDRESS

LINK OUTPUT NUMBERS IPNUM

EZTEXT-DIN INPUT1/Output 1 N/A 1 1

EZTEXT-DIN INPUT2/Output 2 N/A 2 1

725-IP/OP Module Link 1 3-6 2

725-IP/OP Module Link 2 7-10 3

725-IP/OP Module Link 3 11-14 4

725-IP/OP Module Link 4 15-18 5

EZTEXT-DIN

DS-EZTEXT-DIN-3

LED Indication At Start Up

Logging onto Network

(traffic light sequence)

Error!

(All Flash ON / OFF together) Error - No GSM Service

1. Check SIM Card

2. Check Antenna

Connection

LED Indication After Start Up (Normal Operation)

Good OK Poor

Signal Strength Activity LED’s

Receiving an SMS RX

GSM

Transmitting an SMS

Intermittent flash GSM

healthy

EZTEXT-DIN

DS-EZTEXT-DIN-3

Good OK Poor

Signal Strength Activity LED’s

Receiving an SMS RX

GSM

Transmitting an SMS

Intermittent flash GSM

healthy

Title

Command

Description

Example

Password

UPW

UPW#UNITPW

User must send UPW command within 5 mins after

power applied. Setting the UPW is carried out by

sending this text message to the unit.

The User Password (4 – 8 Characters) is case sensitive

and can consist of any letters or numbers.

If for any reason the unit password is lost, remove all

power for 1 minute, and then start again.

UPW#1234

(sets password to

1234)

Response:

UPW OK

Unit identity

UID

UNITPW#UID#UNITID

This sets the ‘identity’ of the EZTEXT unit, and will be

included in any response text from EZTEXT.

The UNITID can be 4 to 10 characters with no spaces.

1234#UID#DoorAlarm

Response:

Door Alarm UID OK

Response

RESPONSE

RESPONSE?

UNITPW#RESPONSE#x

Setup a Reply Text EZTEXT after receiving a command

x=ON or OFF

UNITPW#RESPONSE?

Requests the status of the current RESPONSE setting

NOTE: messages which specifically demand a response

such as requests for input status will always be

responded to as will the UPW, UID etc.

Default setting is for response to be turned off.

1234#RESPONSE#ON

Turns on Response

messages

1234#RESPONSE?

Replies with the

EZTEXT setting to

responses

Error Messages & Factory Reset

There are three error messages;

NO AUTHORISATION Means that EZTEXT did not accept the

password

UNRECOGNIZED COMMAND Password correct but the command is

incorrect

UNRECOGNIZED VARIABLE Password and command OK but the

variable data is incorrect

Factory reset:

Hold down the RESET button for approx10 seconds until all LEDs flash, then

release. This will reset EZTEXT to factory default settings and restart.

User Set-Up Commands

EZTEXT-DIN

DS-EZTEXT-DIN-3

INPUT Commands

Title

Command

Description

Example

Set an input

name

IPNAME

IPNAME?

When the input changes this is the name that the

EZTEXT will transmit in its text message

UNITPW#IPNAMEn#<name>

This designates a <name> to an EZTEXT input

(max15 characters) with no spaces.

n=1 - 2 for inputs1 to 2

UNITPW#IPNAME?

Requests the name given to all inputs

Please note that only the 2 inputs on the main

EZTEXT-DIN module can be given a name.

1234#IPNAME1,Gate

Sets input 1 to be

known as ‘Gate’

1234#IPNAME?

Requests the current

name of input1

Input number

to text

IPNUM

IPNUM?n

IPNUMDEL

Sets the destination phone number(s) (max 5 per

input) when an EZTEXT input is activated.

UNITPW#IPNUMn,<num to text>

n=1 - 2 for inputs1 to 2

UNITPW#IPNUM?n

Requests all Stored cell Nos for that input

UNITPW#IPNUMDELn

n=1 - 2 for inputs1 to 2

Deletes all stored cell Nos for that input number

1234#IPNUM1,00441

234567891

Sets tel No to input 1

1234#IPNUM?1

Requests all stored

telephone numbers for

input 1

1234#IPNUMDEL2

Deletes ALL stored

numbers for input 2

Set number of

input

activations

before SMS

sent

IPCNT

IPCNTVAL?

Sets the number of times an input must be

activated before an SMS is sent

<UNITPW#IPCNTn,x

n= input number (1 or 2)

x= Counter (0 to 65500)

UNITPW#IPCNTVAL?

Requests the actual current value of the counter

1234#IPCNT1,10

A text will be sent after

input 1 has been

activated 10 times

1234#IPCNTVAL?

Responds with ;

INTPUT1= 10/4

intput1 has been

activated 4 times, 6

more activations

required before text

is sent

Delay SMS

on input

activation

IPDLY

IPDLY?

Sets a timer (Max 65500 secs). When the EZTEXT

input is activated the timer starts to countdown in

seconds.

When the counter reaches zero, providing the input

is still activated a text message will be sent.

UNITPW#IPDLYn,xx

n=1 - 2 for inputs1 to 2

‘xx’ can be a number from 0 to 65500

UNITPW#IPDLY?

Requests timer values for all inputs

1234#IPDLY1,60

Input 1 has a 60sec

delay before text is sent

1234#IPDLY?

Responds with ;

INTPUT1= 60/34

(output1 has been ac-

tive for 34 out of a total

60sec preset time.

34secs more is required

before text sent)

EZTEXT-DIN

DS-EZTEXT-DIN-3

Output Commands

Title

Command

Description

Example

Activate an

output

OUT

Turns an output ON or OFF

UNITPW#OUTn,x

n=Relay number = 1 to 18

x=Relay Status = ON, OFF

1234#OUT1,ON

Turns Output1 ON

Set an

output name

OPNAME

OPNAME?

This designates a name to an EZTEXT output

UNITPW#OPNAMEn,name

n=Output no

name= name can be up to 15 characters.

UNITPW#OPNAME?

Requests the name of the Outputs

Please note that only the 2 outputs on the main

EZTEXT-DIN module can be given a name.

1234#OPNAME1,AIRC

sets output 1 name to

be ‘AIRCON’

1234#OPNAME?

Requests names of all

the outputs

Set output

on time

OPDLY

OPDLY?

Sets output operation time. The output can be set

from 1 to 65500 seconds, or If is set to ‘0’, then the

output will latch on

UNITPW#OPDLYn,t

n=Output number

t=Delay time (seconds)

UNITPW#OPDLY?

Requests the current ‘on’ time setting for an output

EZTEXT replies with the preset time delay output and

the actual time that the output has been activated for

1234#OPDLY1,500

Sets output1 to oper-

ate for 500 sec’s

1234#OPDLY?

Responds with ;

OUTPUT1= 500/34

(output1 has been ac-

tive for 34 out of a total

500sec preset time)

Power Fail Commands

Title

Command

Description

Example

Number to

text on

power

Restored

PFNUM

PFNUM?

PFNUMDEL

Texts will be sent to cell phone numbers stored in

PFNUM on reboot after a power failure or reset (when

power is reapplied).

Note: this feature is enabled or disabled by simply

having cell phone numbers in PFNUM.

UNITPW#PFNUM#<numbertotext>

Sets the number to text on power restored

(Max 5 separate numbers)

UNITPW#PFNUM?

Requests the current numbers that are stored

UNITPW#PFNUMDEL

PFNUMDEL Deletes all stored Power Failed cell Nos

1234#PFNUM#004412

73898000

1234 #PFNUM?

Response: Returns

current settings

1234 #PFNUMDEL

Deletes all stored cell

Nos against this

Example of text:

Building2 Reboot power

had failed

EZTEXT-DIN

DS-EZTEXT-DIN-3

Temperature Commands

Command

Description

Example

Request

current

temperature

TEMP?

UNITPW#TEMP?

requests the current temperature.

1234# TEMP?

Set SMS

numbers to

text on trig-

ger

TEMPNUM

TEMPNUM?

TEMPNUM-

DEL

UNITPW#TEMPNUM#<numbertotext>

Sets the cell phone nos (max of 5) linked with the

temperature monitoring.

TEMPNUM?

Requests all linked cell phone nos

TEMPNUMDEL

Deletes all linked cell phone nos

1234#TEMPNUM#004

41234567891

Sets the number

01234 567891

1234#TEMPNUM?

Requests all cell phone

numbers which will be

notified on temp trig-

gers

1234#TEMPNUMDEL

Deletes all the tele-

phone numbers associ-

ated with Temperature

monitoring

Set maxi-

mum trigger

temperature

SETTEMPMAX

UNITPW#SETTEMPMAX#n

Sets the maximum temperature trigger level in

degrees Celsius.

1234#SETTEMPMAX#3

Sets the upper trig-

ger level to 30oC

Set

maximum

trigger

temperature

SETTEMPMIN

UNITPW#SETTEMPMIN#n

Sets the minimum temperature trigger level.

1234#SETTEMPMIN#2

Sets the lower trigger

level to 20oC

13. System Commands

Title

Command

Description

Example

Report GSM

signal

strength

SIGQ

UNITPW#SIGQ

Reports EZTEXT GSM signal strength as;

‘POOR’ (consider alternative antenna)

‘OK’, or ‘Good’.

1234#SIGQ

Response: Signal is good

Retrieve

status of

inputs and

outputs

STATUS

UNITPW#STATUS requests the current status of all

inputs and outputs

1234#STATUS

Response: Returns

current settings

EZTEXT-DIN

DS-EZTEXT-DIN-3

Technical Specifications

Storage Temperature: -10 to +70˚C.

Operating Temperature: 0 to +55˚C.

EZTEXT Dimensions: 136 x 78 x 42 mm

*Notes

Figures refer to maximum supply current required with all components idle.

Figures refer to peak supply current required with all components operating.

In practice internal reservoir capacitance limits the instantaneous peak current to less

than 500 mA.

Temperature accuracy

+/- 0.5 degrees between –10 to +80-degree Centigrade

+/- 2.0 degrees between –55 to +110-degree Centigrade

The relay contacts in this unit are for functional switching only and must not be used for

isolation purposes.

Electrical Characteristics* Min Typical Max Dimension Notes

Supply Voltage 12 24 V

Supply Current for EZTEXT:

Idle

Operating

200

250

Closed Contact Input Time 100 mSecs

Temperature Cable -55 110 oC 3

Mains rated Relay Rating

(230Vac) 5 12 A 4

EZTEXT-DIN 
 
Disclaimer: 
Whilst the information in this document is believed to be correct at the time of issue, RF Solutions Ltd does not accept any liability whatsoever for its accuracy, adequa-
cy or completeness. No express or implied warranty or representation is given relating to the information contained in this document. RF Solutions Ltd reserves the 
right to make changes and improvements to the product(s) described herein without notice.  Buyers and other users should determine for themselves the suitability of 
any such information or products for their own particular requirements or specification(s).  RF Solutions Ltd shall not be liable for any loss or damage caused as a result 
of user’s own determination of how to deploy or use R F Solutions Ltd’s products.  Use of RF Solutions Ltd products or components in life support and/or safety applica-
tions is not authorised except with express written approval. No licences are created, implicitly or otherwise, under any of RF Solutions Ltd’s intellectual property rights. 
Liability for loss or damage resulting or caused by reliance on the information contained herein or from the use of the product (including liability resulting from negligence 
or where RF Solutions Ltd was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict RF Solutions Ltd’s liability     
for death or personal injury resulting from its negligence. 
RF Solutions Ltd. Recycling Notice 
Meets the following EC Directives: 
DO NOT 
Discard with normal waste, please recycle. 
ROHS Directive 2011/65/EU as amended by 2015/863/EU 
Specifies certain limits for hazardous substances.  
WEEE Directive 2012/19/EU  
Waste electrical & electronic equipment. This product must be disposed of through a licensed WEEE collection point. RF Solutions Ltd., fulfils its 
WEEE obligations by membership of an approved compliance scheme. Environment agency registration agency number: WEE/JB0104WV. 
Simplified Declaration of Conformity (RED) 
BG - 
С настоящото RF Solutions Limited декларира, че този тип радиосъоръжение дефинирани в този документ е в съответствие с Директива 2014/53/ЕС. 
Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: www.rfsolutions.co.uk 
CS -
Tímto RF Solutions Limited prohlašuje, že typ rádiového zařízení definované v tomto dokumentu je v souladu se směrnicí 2014/53/EU. Úplné 
znění EU prohlášení o shodě je k dispozici na této internetové adrese: www.rfsolutions.co.uk 
DA - 
Hermed erklærer RF Solutions Limited , at radioudstyrstypen defineret i dette dokument er i overensstemmelse med direktiv 2014/53/EU. 
EU-overensstemmelseserklæringens fulde tekst kan findes på følgende internetadresse: www.rfsolutions.co.uk 
DE - 
Hiermit erklärt RF Solutions Limited , dass der Funkanlagentyp in diesem Dokument definiert der Richtlinie 2014/53/EU entspricht. Der 
vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar: www.rfsolutions.co.uk 
EL - 
Με την παρούσα ο/η RF Solutions Limited , δηλώνει ότι ο ραδιοεξοπλισμός ορίζεται σε αυτό το έγγραφο πληροί την οδηγία 2014/53/ΕΕ. Το πλήρες κείμενο 
της δήλωσης συμμόρφωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο: www.rfsolutions.co.uk 
EN - 
Hereby, RF Solutions Limited declares that the radio equipment type defined within this document is in compliance with Directive 2014/53/
EU. The full text of the EU declaration of conformity is available at the following internet address: www.rfsolutions.co.uk 
ES - 
Por la presente, RF Solutions Limited declara que el tipo de equipo radioeléctrico definido dentro de este documento es conforme con la 
Directiva 2014/53/UE. El texto completo de la declaración UE de conformidad está disponible en la dirección Internet siguiente: 
www.rfsolutions.co.uk 
ET -
Käesolevaga deklareerib RF Solutions Limited , et käesolev raadioseadme tüüp määratletud selles dokumendis vastab direktiivi 2014/53/EL 
nõuetele. ELi vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil: www.rfsolutions.co.uk 
FI -
RF Solutions Limited vakuuttaa, että radiolaitetyyppi määratletud selles dokumendis on direktiivin 2014/53/EU mukainen. EU-
vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa: www.rfsolutions.co.uk 
FR - 
Le soussigné, RF Solutions Limited , déclare que l'équipement radioélectrique du type défini dans ce document est conforme à la directive 
2014/53/UE. Le texte complet de la déclaration UE de conformité est disponible à l'adresse internet suivante: www.rfsolutions.co.uk 
HR - 
RF Solutions Limited ovime izjavljuje da je radijska oprema tipa definirani u ovom dokumentu u skladu s Direktivom 2014/53/EU. Cjeloviti tekst 
EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi: www.rfsolutions.co.uk 
HU - 
RF Solutions Limited igazolja, hogy a dokumentumban meghatározottak szerint típusú rádióberendezés megfelel a 2014/53/EU irányelvnek. 
Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a következő internetes címen: www.rfsolutions.co.uk 
IT - 
Il fabbricante, RF Solutions Limited , dichiara che il tipo di apparecchiatura radio definito all'interno di questo documento è conforme alla diret-
tiva 2014/53/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: www.rfsolutions.co.uk 
LT - 
Aš, RF Solutions Limited , patvirtinu, kad radijo įrenginių tipas apibrėžta šiame dokumente atitinka Direktyvą 2014/53/ES. Visas ES atitikties 
deklaracijos tekstas prieinamas šiuo interneto adresu: www.rfsolutions.co.uk 
LV - 
Ar šo RF Solutions Limited deklarē, ka radioiekārta kas definēts šajā dokumentā atbilst Direktīvai 2014/53/ES. Pilns ES atbilstības deklarācijas 
teksts ir pieejams šādā interneta vietnē: www.rfsolutions.co.uk 
MT - 
B'dan, RF Solutions Limited , niddikjara li dan it-tip ta' tagħmir tar-radju definit f'dan id-dokument huwa konformi mad-Direttiva 2014/53/UE. 
It-test kollu tad-dikjarazzjoni ta' konformità tal-UE huwa disponibbli f'dan l-indirizz tal-Internet li ġej: www.rfsolutions.co.uk 
NL - 
Hierbij verklaar ik, RF Solutions Limited , dat het type radioapparatuur gedefinieerd in dit document conform is met Richtlijn 2014/53/EU. De 
volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres: www.rfsolutions.co.uk 
PL - 
RF Solutions Limited niniejszym oświadcza, że typ urządzenia radiowego zdefiniowane w tym dokumencie jest zgodny z dyrektywą 2014/53/UE. 
Pełny tekst deklaracji zgodności UE jest dostępny pod następującym adresem internetowym: www.rfsolutions.co.uk 
PT - 
O(a) abaixo assinado(a) RF Solutions Limited declara que o presente tipo de equipamento de rádio definido neste documento está em con-
formidade com a Diretiva 2014/53/UE. O texto integral da declaração de conformidade está disponível no seguinte endereço de Internet: 
www.rfsolutions.co.uk 
RO - 
Prin prezenta, RF Solutions Limited declară că tipul de echipamente radio definit în acest document este în conformitate cu Directiva 
2014/53/UE. Textul integral al declarației UE de conformitate este disponibil la următoarea adresă internet: www.rfsolutions.co.uk 
SK - 
RF Solutions Limited týmto vyhlasuje, že rádiové zariadenie typu definované v tomto dokumente je v súlade so smernicou 2014/53/EÚ. Úplné 
EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese: www.rfsolutions.co.uk 
SL - 
RF Solutions Limited potrjuje, da je tip radijske opreme opredeljeno v tem dokumentu skladen z Direktivo 2014/53/EU. Celotno besedilo izjave 
EU o skladnosti je na voljo na naslednjem spletnem naslovu: www.rfsolutions.co.uk 
SV - 
Härmed försäkrar RF Solutions Limited att denna typ av radioutrustning definieras i detta dokument överensstämmer med direktiv 2014/53/
EU. Den fullständiga texten till EU-försäkran om överensstämmelse finns på följande webbadress: www.rfsolutions.co.uk 