Rotel A14 Manuale del proprietario

A14

Stereo Integrated Amplier

Amplicateur Stéréo Intégré

Stereo-Vollverstärker

Amplicador Integrado Estereofónico

Geïntegreerde stereoversterker

Amplicatore integrato stereo

Integrerad stereoförstärkare

Интегрированный стерео усилитель

Owner’s Manual

Manuel de l’utilisateur

Bedienungsanleitung

Manual de Instrucciones

Gebruikershandleiding

Manuale di istruzioni

Instruktionsbok

Инструкция пользователя

2

A14 Stereo Integrated Amplier

You must allow a minimum 10 cm or 4 inches of unobstructed

clearance around the unit.

WARNING: The rear panel power cord connector is the mains power

disconnect device. The device must be located in an open area that

allows access to the cord connector.

The unit must be connected to a power supply only of the type and

voltage specified on the rear panel. (USA: 120 V/60Hz, EC: 230V/50Hz)

Connect the component to the power outlet only with the supplied

power supply cable or an exact equivalent. Do not modify the supplied

cable. Do not use extension cords.

The mains plug is the disconnect of the unit. In order to completely

disconnect the unit from the supply mains, remove the main plug from

the unit and the AC power outlet. This is the only way to completely

remove mains power from the unit.

Use Class 2 wiring for speaker connections to ensure proper installation

and minimize the risk of electrical shock.

The batteries in the remote control should not be exposed to excessive

temperature such as sunshine, re or other heat sources. Batteries

should be recycled or disposed as per state and local guidelines.

Notice

The RS232 connection should be handled by authorized persons only.

WARNING: There are no user serviceable parts inside. Refer all

servicing to qualified service personnel.

WARNING: To reduce the risk of fire or electric shock, do not expose

the unit to moisture or water. Do not expose the unit to dripping or

splashing. Do not place objects filled with liquids, such as vases, on

the unit. Do not allow foreign objects to get into the enclosure. If the

unit is exposed to moisture, or a foreign object gets into the enclosure,

immediately disconnect the power cord from the wall. Take the unit

to a qualified service person for inspection and necessary repairs.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type

plug. A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult an electrician

for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly

at plugs, convenience receptacles, and the point where they exit

from the apparatus.

Only use attachments/accessories specified by the manufacturer.

Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use with caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused for

long periods of time.

Refer all servicing to qualified service personnel. Servicing is required

when the apparatus has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or has been dropped.

The apparatus should be used in non tropical climate.

Rotel products are designed to comply with

international directives on the Restriction of Hazardous

Substances (RoHS) in electrical and electronic

equipment and the disposal of Waste Electrical and

Electronic Equipment (WEEE). The crossed wheelie bin

symbol indicates compliance and that the products must

be appropriately recycled or processed in accordance

with these directives.

Important Safety Instructions

POWER

PHONES

A12

PHONO TUNER CD USB OPT COAX AUX PC-USB BT

5V / 2.1A

MENU

SPEAKERS

A B

POWER

PHONES

A14

PHONO TUNER CD USB OPT COAX AUX PC-USB BT

5V

/

2.1A

MENU

SPEAKERS

A B

This symbol means that this unit is double insulated.

An earth connection is not required.

3

Figure 1: Controls and Connections

Commandes et Branchements

Bedienelemente und Anschlüsse

Controles y Conexiones

Controlli e connessioni

De bedieningsorganen en aansluitingen

Kontroller och anslutningar

Органы управления и разъемы

POWER

PHONES

A 14

PHONO TUNER CD USB OPT COAX AUX PC-USB BT

5V / 2.1A

MENU

SPEAKERS

A B

0 - =

q w

e r

t

y

u

i o

[

] \

a s

1

2 3

4

5

6

7

8

9

p

4

A14 Stereo Integrated Amplier

A

B

C

D

E

F

G

H

I

N

L

K

J

M

Figure 2: Remote Control RR-AX1400

Télécommande infra-rouge RR-AX1400

Fernbedienung RR-AX1400

Mando a Distancia RR-AX1400

Telecomando RR-AX1400

De afstandsbediening RR-AX1400

Fjärrkontroll RR-AX1400

Пульт ДУ RR-AX1400

5

Figure 3: Preamp Input and Speaker Output Connections

Branchements des entrées sources et sorties enceintes acoustiques

Anschlussdiagramm

Conexiones para Entrada de Señal y Salida a las Cajas Acústicas

Collegamenti ingressi e diffusori

De signaalingangen en de luidsprekeruitgangen

Signal- och högtalaranslutningar

Подсоединение источников сигнала и акустических систем

Amplifier A14

CD PLAYER

PHONO

6

A14 Stereo Integrated Amplier

Figure 4: Digital Input Connections

Branchements Entrées numériques

Digitaleingänge-Anschlüsse

Conexiones Entradas Digitales

Digitale ingang verbinding

Collegamenti ingressi digitali

Anslutningar för digitala ingångar

Подсоединение Цифровые входы

Computer

CLASS 1

LASER PRODUCT

APPAREIL LASER

DE CLASSE 1

MODEL NO.: CD14

RP-572C

Amplier A14

(Supplied)

CD Player CD14

7

Figure 5: Rotel Link and 12V Trigger Connections

Branchements Rotel Link et trigger 12 V

Rotel Link- und 12V-Trigger-Anschlüsse

Conexiones Rotel Link y para Señal de Disparo de 12V

CLASS 1

LASER PRODUCT

APPAREIL LASER

DE CLASSE 1

MODEL NO.: CD14

RP-572C

CD Player CD14

Amplifier A14

T14

NETWORK TUNER

R

ANTENNA

FM

DAB

L

OUTPUT

COAXIAL OUT

USB

RS232

12V TRIGGER

IN OUTOUT

ROTEL LINK

OUT

RP-571B

Tuner T14

WIFI ANTENNA

Important! : The 12V trigger cables will override the Rotel Link commands. Do not connect the 12V trigger cable if Rotel Link is connected.

Important : Les connexions trigger 12v sont prioritaires sur les commandes Rotel Link. Ne branchez pas de câble trigger 12 V si une connexion

Rotel Link a été réalisée.

Wichtig! Die 12V-Trigger-Kabel umgehen die Rotel Link-Befehle. Schließen Sie kein 12V-Trigger-Kabel an, wenn die Rotel Link-Verbindung

hergestellt wurde.

¡Importante!: Los cables para señal de disparo de 12V bloquearán las órdenes de control vía Rotel Link. Por lo tanto, cuando el Rotel Link esté

conectado no conecte ningún cable para señal de disparo de 12V.

Importante! I segnali Trigger 12 V hanno la precedenza sui comandi Rotel Link, pertanto non effettuare i collegamenti Trigger 12 V se si utilizza

il bus Rotel Link.

Belangrijk: De 12V trigger aansluitingen hebben voorrang op de Rotel Link opdrachten. Sluit dus niet de 12V triggerkabel en Rotel Link tegelijkertijd

aan.

Viktigt! Kablarna för 12 V styrsignaler åsidosätter Rotel Link-kommandon. Anslut inte kablar för 12 V styrsignal om det nns en Rotel Link-anslutning.

Внимание! : 12-В триггерный сигнал имеет приоритет над командами шины Rotel Link. Не подсоединяйте кабель 12-В триггерного

сигнала, если уже сделано соединение по Rotel Link.

De Rotel Link en 12V trigger aansluitingen

Collegamenti Rotel Link e segnali Trigger 12 V

Rotel Link-anslutning och 12 V-anslutning för styrsignal

Подсоединение Rotel Link и 12-В триггерного сигнала

8

A14 Stereo Integrated Amplier

POWER

PHONES

A 14

PHONO TUNER CD USB OPT COAX AUX PC-USB BT

5V

/

2.1A

MENU

SPEAKERS

A B

iPhone

Figure 6: Front USB Input

Entrée USB en face avant

Frontseitiger USB-Eingang

Entrada USB Frontal

USB-ingang op het voorpaneel

Ingresso USB frontale

USB-port på fronten

USB вход на передней панели

9

Important Notes

When making connections be sure to:

 Turn off all the components in the system before hooking up any components, including loudspeakers.

4 Turn off all components in the system before changing any of the connections to the system.

It is also recommended that you:

4 Turn the volume control of the ampliﬁer all the way down before the ampliﬁer is turned on or off.

Remarques importantes

Pendant les branchements, assurez-vous que :

 Tous les maillons sont éteints avant leur branchement, quels qu’ils soient, y compris les enceintes acoustiques.

4 Éteignez tous les maillons avant de modiﬁer quoi que ce soit au niveau de leurs branchements, quels qu’ils soient.

Il est également recommandé de :

4 Toujours baissez le niveau sonore via le contrôle de volume, avant d’allumer ou d’éteindre l’ampliﬁcateur.

Wichtige Hinweise

Achten Sie beim Herstellen der Verbindungen auf Folgendes:

4 Schalten Sie alle Komponenten im System ab, bevor Sie Geräte (einschließlich Lautsprecher) anschließen.

4 Schalten Sie alle Komponenten im System ab, bevor Sie Anschlüsse im System verändern.

Ferner empfehlen wir, dass

4 Sie die Lautstärke herunterdrehen, bevor Sie die Endstufe ein- oder abschalten.

Notas Importantes

Cuando realice las conexiones, asegúrese de que:

4 Desactiva todos los componentes del equipo, cajas acústicas incluidas, antes de conectar cualquier nuevo componente en el mismo.

 Desactiva todos los componentes del equipo antes de cambiar cualquier conexión del mismo.

También le recomendamos que:

 Reduzca el nivel de volumen de su ampliﬁcador a cero antes de activarlo o desactivarlo.

Héél belangrijk

Bij het maken van de verbindingen:

 Zorg dat niet alleen de A14, maar de gehele installatie uitstaat, als nog niet alle verbindingen gemaakt zijn.

 Zorg dat niet alleen de A14, maar de gehele installatie ook uitstaat, als u verbindingen gaat wijzigen.

Wij raden u ook aan om

 de volumeregelaar van de voorversterker geheel dicht te draaien (volkomen naar links) wanneer u uw eindversterker aan- of uitzet.

Note importanti

Quando effettuate i collegamenti assicuratevi di:

 Spegnere tutti i componenti del sistema prima di collegare qualsiasi componente, inclusi i diffusori.

 Spegnere tutti i componenti del sistema prima di modiﬁcare qualsiasi connessione nel sistema.

Vi raccomandiamo inoltre di:

 Portare il volume a zero prima di accendere o spegnere l’ampliﬁcatore.

Viktigt

Tänk på följande när du gör anslutningar:

4 Stäng av alla apparater i anläggningen innan du ansluter nya komponenter eller högtalare.

4 Stäng av alla apparater i anläggningen innan du ändrar någon anslutning.

Du rekommenderas också:

 Vrid ner volymen på förförstärkaren helt och hållet innan förstärkaren slås på eller av.

Важные замечания

Перед подсоединением:

4 Выключите все компоненты, включая колонки.

 Выключите все компоненты в вашей системе, прежде чем что-то в ней менять.

Рекомендуется также:

 Вывести громкость усилителя на минимум, перед тем как включать или выключать его.

10

A14 Stereo Integrated Amplier

About Rotel

Our story began over 50 years ago. Over the decades, we have received

hundreds of awards for our products and satised hundreds of thousands

of people who take their entertainment seriously – like you.

Rotel was founded by a family whose passionate interest in music led them

to manufacture high-delity components of uncompromising quality.

Through the years, that passion has remained undiminished and the family

goal of providing exceptional value for audiophiles and music lovers,

regardless of their budget, is shared by all Rotel employees.

Rotel’s engineers work as a close team, listening to, and ne tuning, each

new product until it reaches their exacting musical standards. They are

free to choose components from around the world in order to make that

product the best they can. You are likely to nd capacitors from the United

Kingdom and Germany, semiconductors from Japan or the United States,

while toroidal power transformers are manufactured in Rotel’s own factory.

We all have concerns about our environment. And, as more and more

electronics are produced it is especially important for a manufacturer to do all

it can to engineer products that have a minimum impact on the environment.

At Rotel, we are proud to do our part. We have reduced the lead content

in our products by using special lead-free ROHS solder and components.

Our engineers continually strive to improve power supply efciency without

compromise to quality. When in standby mode Rotel products use minimal

power to meet global Standby Power Consumption requirements.

The Rotel factory is also doing their part to help the environment through

constant improvements to product assembly methods for a cleaner and

greener manufacturing processes.

All of us at Rotel thank you for buying this product. We are sure it will bring

you many years of enjoyment.

Getting Started

Thank you for purchasing the Rotel A14 Stereo Integrated Amplier. When

used in a high-quality music audio system, Rotel products will provide years

of musical enjoyment.

This amplier is a full featured, high performance component. All aspects

of the design have been optimized to retain the full dynamic range and

subtle nuances of your music. The unit has a highly regulated power supply

incorporating a Rotel custom-designed toroidal power transformer. This low

impedance power supply has ample power reserves, which enables the

amplier to easily reproduce the most demanding audio signals. This type

of design is more expensive to manufacture, but it is better for the music.

The printed circuit boards (PCB) are designed with Symmetrical Circuit

Traces. This ensures that the precise timing of the music is maintained and

faithfully recreated. The circuitry uses metal lm resistors and polystyrene

or polypropylene capacitors in important signal paths. All aspects of this

design have been examined to ensure the most faithful music reproduction.

The main functions of the A14 are easy to install and use. If you have

experience with other stereo systems, you shouldn’t nd anything perplexing.

Simply plug in the associated components and enjoy.

Contents

Important Safety Instructions ..........................................2

Figure 1: Controls and Connections 3

Figure 2: Remote Control RR-AX1400 4

Figure 3: Preamp Input and Speaker Output Connections 5

Figure 4: Digital Input Connections 6

Figure 5: Rotel Link and 12V Trigger Connections 7

Figure 6: Front USB Input 8

Important Notes 9

About Rotel ......................................................10

Getting Started ...................................................10

A Few Precautions 11

Placement 11

Cables 11

The RR-AX1400 Remote Control .......................................11

Second Amplier Remote Code 11

Remote Control Batteries 11

AC Power and Control ..............................................11

AC Power Input

s

11

Power Switch

1

A

and Power Indicator

2

12

12V Trigger Connection

u

12

Protection Indicator

2

.............................................12

Input Signal Connections ............................................12

Phono Input

-

and Ground Connection (GND)

0

12

Line Level Inputs

=qw

12

Digital Signal Inputs

]

12

Preamp Output

[

................................................12

Speaker Outputs

\a

.............................................12

Speaker Selector Switch

5

12

Speaker Selection 12

Speaker Wire Selection 12

Polarity and Phasing 13

Speaker Connection 13

Headphone Output

4

..............................................13

Display

6

......................................................13

Front USB Input

3

...............................................13

APTX Bluetooth Connection

e

........................................13

Rear USB Power port

p

............................................13

Audio Controls ....................................................13

Volume Control

7

E

13

Balance Control

9

B

13

Tone Control Bypass

9

B

13

Bass and Treble Controls

9

B

14

Source Input Selector

8

I

14

Dimmer Control ...................................................14

Display Dimmer

9

D

14

LED Dimmer

9

14

PC-USB Input

r

..................................................14

Rotel Link

t

....................................................14

EXT REM IN Jack

y

...............................................15

RS232 Connector

i

...............................................15

Network Connection

o

............................................15

Settings Menu ....................................................15

Troubleshooting ...................................................17

Power Indicator Is Not Illuminated 17

Fuse Replacement 17

No Sound 17

Playable Audio Formats 17

Cannot Connect via Bluetooth 17

Specications .....................................................18

11

A Few Precautions

WARNING: To avoid potential damage to your system, turn off ALL

the components in the system when connecting or disconnecting the

loudspeakers or any associated components. Do not turn the system

components back on until you are sure all the connections are correct

and secure. Pay particular attention to the speaker wires. There must

be no loose strands that could contact the other speaker wires, or the

chassis of the amplifier.

Please read this manual carefully. It provides information on how to

incorporate the unit into your system as well as information that will help

you get optimum sound performance. Please contact your authorized Rotel

dealer for answers to any questions you might have. In addition, all of us

at Rotel welcome your questions and comments.

Save the shipping carton and all enclosed packing material for future use.

Shipping or moving the amplier in anything other than the original packing

material may result in severe damage to your amplier.

If included in the box please ll out and send in the owner’s registration

card. Also be sure to keep the original sales receipt. It is your best record

of the date of purchase, which you will need in the event warranty service

is ever required.

Placement

Like all audio components that handle low level signals, this amplier

can be affected by its environment. Avoid placing the unit on top of other

components. Also avoid routing audio signal cables near power cords. This

will minimize the chance it will pick up hum or interference.

The unit generates heat as part of its normal operation. The heat sinks and

ventilation openings in the amplier are designed to dissipate this heat. The

ventilation slots in the top cover must be open. There should be 10 cm (4

inches) of clearance around the chassis, and reasonable airow through

the installation location, to prevent the amplier from overheating.

Remember the weight of the amplier when you select an installation location.

Make sure that the shelf or cabinet can support it. We recommend installing

the unit in furniture designed to house audio components. Such furniture is

designed to reduce or suppress vibration which can adversely affect sound

quality. Ask your authorized Rotel dealer for advice about component

furniture and proper installation of audio components.

Cables

Be sure to keep the power cords, digital signal cables and analog audio

signal cables in your installation away from each other. This will minimize

the chance of the analog audio signal cables picking up noise or interference

from the power cords or digital cables. Using only high quality, shielded

cables will also help to prevent noise or interference from degrading the

sound quality of your system. If you have any questions see your authorized

Rotel dealer for advice about the best cable to use with your system.

The RR-AX1400 Remote Control

Some functions can be done with either the front panel controls, or the

supplied RR-AX1400 remote control. When these operations are described,

the square call out numbers refer to the main unit, while the encircled letters

refer to the remote control.

Second Amplier Remote Code

The factory setting is remote code 1. If you nd that the remote is conicting

with other Rotel ampliers, you can change to remote code 2 with the

following steps.

1. From the remote control press Tuner

I

and 2

M

at the same time for 5

seconds, to set the remote control to send Audio Code 2.

2. Point the remote at the unit and press 2

M

button for 14 seconds. The

unit will show “Audio Code SET 1 -> 2”.

3. Repeat the above procedure and press “1” key instead of “2” to change

the unit back to Code 1.

NOTE: The remote control can be used to operate the basic functions

of Rotel tuners and CD players. Remote control keys labeled

GHMN

can be used to operate CD or Tuner functions in your system. For the

remote to operate properly, make sure both the remote and the CD or

Tuner are both in same remote code, either Code 1 or 2.

Remote Control Batteries

Two AAA size batteries (supplied) must be installed before the remote control

can be used. To install the batteries, remove the cover on the back of the

RR-AX1400. Install the batteries as shown in the illustration in the battery

well. Test the control for proper operation, then replace the cover. When the

batteries become weak the remote control won’t operate the A14 consistently.

Installing fresh batteries should eliminate the problem.

AC Power and Control

AC Power Input

s

Your unit is congured at the factory for the proper AC line voltage in the

country where you purchased it (either 120 volts AC or 230 volts AC with

a line frequency of either 50 Hz or 60 Hz). The AC line conguration is

noted on a decal on the back panel.

NOTE: Should you move your amplifier to another country, it is possible

to reconfigure it for use on a different line voltage. Do not attempt to

perform this conversion yourself. Opening the enclosure of the unit

exposes you to dangerous voltages. Consult a qualified service person

or the Rotel factory service department for information.

NOTE: Some products are intended for sale in more than one country

and as such are supplied with more than one AC cord. Please only use

the one appropriate for your country/region.

The unit does not draw high levels of current from the power outlet. However,

it should be plugged directly into a polarized wall outlet using the supplied

cable or other compatible cable as recommended by your authorized Rotel

dealer. Do not use an extension cord. A heavy duty multi-tap power outlet

strip may be used if it (and the wall outlet) can handle the current demanded

by the amplier and all the other components connected to it.

If you are going to be away from home for an extended period of time

such as a month-long vacation, it is a sensible precaution to unplug your

amplier (as well as other audio and video components) while you are away.

12

A14 Stereo Integrated Amplier

Power Switch

1

A

and Power Indicator

2

Press the front panel Power Switch button

1

, to turn the unit on. The Power

Indicator light

2

is illuminated when the unit is on. Press Power Switch

button again to turn the unit off.

When the power switch is in the ON position, the remote control ON and

OFF buttons may be used to activate the A14. In Standby mode the power

LED is red, but the display is turned OFF.

12V Trigger Connection

u

See Figure 5

Some audio components can be turned on automatically when they receive

a 12V turn on signal. The two 12V Trigger Outputs of the A14 unit provide

the required signal. Connect compatible components to the amplier with a

conventional 3.5mm mini plug cable. When the unit is in standby mode or

turned off, the trigger signal is interrupted, and the components controlled

by it are turned off.

NOTE: If you are using other units in the series with Rotel Link, please

use the Rotel Link connection to turn the units on or off. Do not connect

both the Rotel Link and 12V trigger cables. The 12V trigger’s power

on or off features will override the Rotel Link features.

Protection Indicator

2

The amplier has both thermal and over-current protection circuitry that

protects the amplier against damage in the event of extreme or faulty

operating conditions. The protection circuits are independent of the audio

signal and have no impact on sonic performance. Instead, the protection

circuits monitor the temperature of the output devices and shut down the

amplier if temperatures exceed safe limits.

Most likely, you will never see this protection circuitry in action. However,

should a faulty condition arise, the amplier will stop playing and will

display “AMP PROTECTION“ on the front panel. The power indicator 2

on the front panel will turn red.

If this happens, turn the amplier off. Let it cool down for several minutes,

and attempt to identify and correct the problem that caused the protection

circuitry to engage. When you turn the amplier back on, the protection

circuit will automatically reset and the power indicator 2 should turn blue.

In most cases, the protection circuitry activates because of a fault condition

such as shorted speaker wires, or inadequate ventilation leading to an

overheating condition. In very rare cases, highly reactive or extremely

low impedance speaker loads could cause the protection circuit to engage.

If the protection circuitry triggers repeatedly and you are unable to isolate

and correct the faulty condition, contact your authorized Rotel dealer for

assistance in troubleshooting.

Input Signal Connections

See Figure 3

NOTE: To prevent loud noises that neither you nor your speakers will

appreciate, make sure the system is turned off when you make any

signal connections.

Phono Input

-

and Ground Connection (GND)

0

Plug the cable from the turntable into the appropriate left and right phono

inputs. If the turntable has a “ground” wire, connect it to the screw terminal

to the left of the Phono inputs. It will help prevent hum and noise.

Line Level Inputs

=qw

The CD, Tuner, and Aux inputs of the amplier are “line level” inputs. These

are for connecting components such as CD players or other audio playback

devices with an analog audio output.

The Left and Right channels are labeled and should be connected to the

corresponding channels of the source component. The Left connectors

are white, the Right connectors are red. Use high quality RCA cables for

connecting input source components to the unit. Ask your authorized Rotel

dealer for advice about cables.

Digital Signal Inputs

]

See Figure 4

There are two sets of digital inputs labeled 1 and 2 for COAXIAL and

OPTICAL respectively. Connect the COAXIAL or OPTICAL outputs of your

source component into these sockets. The digital signals will be decoded

and played by the amplier. The unit is capable of decoding PCM signals

up to 24 bit, 192kHz.

Preamp Output

[

The amplier has a set of preamp outputs labeled PRE OUT. The currently

selected source input is available from this output. Typically the PRE OUT

output is used to provide a signal to another integrated amplier or power

amplier, which is used to drive remote speakers.

NOTE: Changes to the settings of the Volume, Balance or Tone controls

affect the signal from the Preamp Output.

Speaker Outputs

\a

See Figure 3

Speaker Selector Switch

5

The amplier has two sets of speaker outputs, labeled “SPEAKER A”

\

and

“SPEAKER B”

a

. The speaker outputs are controlled by the A-B speaker

selector buttons

5

on the front panel or J on the remote control.

Speaker Selection

If only one set of speakers will be used at any given time, the speakers may

have an impedance as low as 4 ohms. If there are times when both the A

and B speakers will be used, all the speakers should have an impedance

of 8 ohms or more. Speaker impedance ratings are less than precise. In

practice, very few loudspeakers will present any problems for the unit. See

your authorized Rotel dealer if you have any questions.

Speaker Wire Selection

Use insulated two-conductor stranded wire to connect the unit to the speakers.

The size and quality of the wire can have an audible effect on the performance

of the system. Standard speaker wire will work, but can result in lower

output or diminished bass response, particularly over longer distances. In

general, heavier wire will improve the sound. For best performance, you

may want to consider special high-quality speaker cables. Your authorized

Rotel dealer can help in the selection of cables for your system.

13

Polarity and Phasing

The polarity - the positive/negative orientation of the connections - for every

speaker and amplier connection must be consistent so all the speakers will

be in phase. If the polarity of one connection is reversed, bass output will

be very weak and stereo imaging degraded. All wire is marked so you can

identify the two conductors. There may be ribs or a stripe on the insulation

of one conductor. The wire may have clear insulation with different color

conductors (copper and silver). There may be polarity indications printed

on the insulation. Identify the positive and negative conductors and be

consistent with every speaker and amplier connection.

Speaker Connection

Turn off all the components in the system before connecting the speakers.

The amplier has color-coded binding post type speaker connectors on the

back panel. These connectors accept bare wire, connector lugs, or dual

banana type connectors. (Except in European Community countries where

their use is not permitted.)

Route the wire from the amplier to the speakers. Give yourself enough slack

so you can move the components to allow access to the speaker connectors.

If you are using dual banana plugs, connect them to the wires and then

plug into the backs of the binding posts. The thumbscrews of the binding

posts should be screwed in all the way (clockwise).

If you are using terminal lugs, connect them to the wires. If you are attaching

bare wires directly to the binding posts, separate the wire conductors and

strip the insulation from the end of each conductor. Be careful not to cut

into the wire strands. Unscrew (turn counterclockwise) the binding post

thumbscrews. Place the connector lug or wire around the binding post

shaft. Turn the thumbscrews clockwise to clamp the connector lug or wire

rmly in place.

NOTE: Be sure there are no loose wire strands that could touch adjacent

wires or connectors.

Headphone Output

4

The headphone output allows you to connect headphones for private listening.

This output accepts a standard 3.5mm (1/8”) mini stereo headphone

connector. Plugging in a set of headphones does not cut off the signal to the

speakers. Use the front panel

5

or remote control

J

A-B speaker selector

buttons to turn off the speakers.

NOTE: Because the sensitivity of speakers and headphones can

vary widely, always reduce the volume level before connecting or

disconnecting headphones.

Display

6

The front panel display shows the source selected, volume level and tone

settings. The display provides access to the setup and conguration menu

options of the amplier.

Front USB Input

3

The front USB input can be connected to an iPhone, iPad or iPod device

providing music playback to the amplier. To enable audio playback using

one of these devices simply plug the device into the front USB and select

USB as the desired source. The device will remain active allowing search

and play functions.

APTX Bluetooth Connection

e

The Bluetooth Antenna e on the A14’s back panel is for wireless streaming

via Bluetooth, from your device (i.e. mobile phones, tablets or computers).

From your device, look for “Rotel Bluetooth” and connect to it. Connection

is normally automatic, but if prompted for a password, please enter “0000”

on your device. The A14’s supports both traditional Bluetooth and APTX

Bluetooth audio streaming.

Rear USB Power Port

p

The rear USB port provides 5V/0.5A for charging or powering USB devices

including streaming music players. This port does not allow playback of audio.

The port can be congured to remain powered even when the A14 is in

standby mode through the front panel setup menu (See USB POWER option

on page 15).

This conguration option allows the attached streaming source to remain

powered for use with the Signal Sense function for automatic power on/

off control of the amplier.

NOTE: When configured to provide continuous power to the rear

panel USB port the A14 will consume additional power even when in

standby mode.

Audio Controls

Volume Control

7

E

Turn the control clockwise to increase the volume, or counter clockwise to

decrease the volume. From the remote control press the volume + or - button

to turn the volume up or down. Press the MUTE

F

button to completely

mute the volume.

Balance Control

9

B

The Balance Control adjusts the left-to-right balance of the sound output. The

factory default is the center position or “0”. To change the balance from

the front panel, press the MENU

9

button to toggle the front display to

BALANCE setting mode. Then press the - or + buttons on the front panel to

change the value to LEFT or RIGHT. The value can change from L15 to R15.

NOTE: This setting is saved permanently including after powering off

the A14.

To make temporary changes not saved after power off, from the remote,

press the BAL

B

button to access the BALANCE SETTING menu, then press

the up/down/left/right

C

arrow buttons to adjust.

Tone Control Bypass

9

B

Bass and Treble Control (Tone Control) circuits are bypassed at factory

default to ensure the purest possible sound. The front display will show

TONE BYPASS. To turn on the tone control from the front panel, press the

MENU

9

button to toggle to the Bypass control then press the - or + buttons

to turn bypass on or off.

14

A14 Stereo Integrated Amplier

NOTE: This setting is saved permanently including after powering off

the A14.

To temporarily changes the Tone Control Bypass, press the BYPASS

B

button

on the remote control to toggle the Bypass mode enabled and disabled.

Bass and Treble Controls

9

B

Set the Bass or Treble controls from the front panel by pressing the MENU

9

button to the Bass and Treble Setting menu in sequence. Press the - or +

buttons to adjust the value. The Bass and Treble values range from -10 to +10.

NOTE: These settings are saved permanently including after powering

off the A14.

To temporarily change the Bass and Treble settings from the remote control,

press the BASS or TREB

B

button, then press the up/down/left/right

C

arrow buttons on the remote to adjust the value.

NOTE: Bass and Treble changes are only available when Tone Bypass

is disabled (see Tone Control Bypass section).

A properly setup high-performance audio system produces the most natural

sound with little or no adjustment of the tone controls. Use these controls

sparingly. Be particularly careful when turning the controls up. This increases

the power output in the bass or treble range, increasing the load on the

amplier and speakers.

NOTE: Setting the Bass and Treble controls do not automatically turn

on the tone control. To turn on tone control, refer to previous section

Tone Control Bypass.

Source Input Selector

8

I

Press the corresponding input button on the front panel

8

or remote control

I

to select the desired listening source.

Push the front panel source buttons to toggle between Optical 1 - 2, Coaxial

1- 2 and Aux 1 - 2 or use the dedicated source button on the remote control.

Dimmer Control

Display Dimmer

9

D

To change the brightness of the front display, press the MENU

9

button

to toggle to the DIMMER Settings. Then press the - or + buttons on the front

panel to change the display brightness.

NOTE: This setting is saved permanently including after powering off

the A14.

To temporarily change the display brightness, press the DIM

D

button on

the remote.

LED Dimmer

9

To change the brightness of the Power LED and the two Speaker Selector

LEDs on the front panel, press the MENU

9

button to toggle to the LED

DIMMER Settings. Then press the - or + buttons on the front panel to change

the LEDs brightness.

NOTE: This setting is saved permanently including after powering off

the A14.

PC-USB Input r

See Figure 4

Connect this input using the supplied USB cable to the PC-USB socket of

your computer.

The A14 supports both USB Audio Class 1.0 and USB Audio Class 2.0

modes. Windows computers do not require installation of a driver for USB

Audio Class 1.0 and support playback of audio up to 96kHz sampling

rates. The Factory Default setting is USB Audio Class 1.0.

To take advantage of USB Audio Class 2.0 audio playback supporting up to

384kHz sampling rates you will need to install the Windows driver supplied

on the CD included with the A14. You will also need to switch the A14 to

USB Audio Class 2.0 playback mode with the following:

• Press MENU on the front panel until “PC-USB CLASS” appears on the display.

• Select “2.0” using the “+” button.

• Power cycle the A14 and reboot your PC after changing the USB Audio

mode to ensure both units are properly congured.

Many audio playback applications do not support 384kHz sampling rate.

Please conrm your audio player supports 384kHz audio and you have

384kHz audio les to properly playback this sample rate. Also, you may

need to congure the audio driver in your PC to output 384kHz or your

computer may “down sample” to a lower audio sample rate. For more

information please refer to your audio player or operating system information.

NOTE: USB Audio Class 2.0 requires installation of the Windows PC

driver on the CD ROM included with the A14.

NOTE: MAC computers do not require a driver to support PC-USB

Audio Class 1.0 or 2.0.

NOTE: Upon successful installation of the driver, you may need to select

the ROTEL audio driver from the audio/speaker setup of your computer.

NOTE: The A14 supports both DSD and DOP audio playback in 1X

and 2X formats. Consult your audio player to confirm proper operation

for playback of these audio formats.

Rotel Link

t

See Figure 5

The ROTEL LINK OUT connection can be made with the stereo 3.5 mm cable

(supplied) to a Rotel product with ROTEL LINK IN connection including a

CD player.

These allow the attached Rotel products to communicate with each other and

be controlled via the Rotel App (available for download on the iTunes

®

store).

NOTE: Only the Rotel Link cables supplied with this product should be

used. These 3.5 mm cables have WHITE connector ends and should

not be confused with the 12 Volt Trigger cables that have BLACK

connector ends.

15

EXT REM IN Jack

y

This 3.5mm mini-jack receives command codes from industry-standard infrared

receivers via hard-wired connections. This feature could prove useful when

the unit is installed in a cabinet and the front-panel sensor is blocked. Consult

your authorized Rotel dealer for information on these external repeaters and

the proper wiring of a jack to t the mini-jack receptacle.

RS232 Connector

i

The A14 can be controlled via RS232 for integration with automation systems.

The RS232 input accepts a standard straight DB-9 Male-to-Female cable.

For additional information on the connections, software, and operating

codes for RS232 control of the A14, contact your authorized Rotel dealer.

Network Connection

o

The A14 can be attached to a network using the rear panel NETWORK

socket o. The NETWORK congurations allow both STATIC and DHCP

IP addressing. See the Network section of this manual under Setting Menu

for IP address conguration information.

The NETWORK connection allows software updates to be downloaded from

the Internet. The NETWORK connection also allows IP control for integration

with automation systems.

For additional information on the IP control please contact your authorized

Rotel dealer.

Settings Menu

You can access the SETUP menu from the front panel by pressing the MENU

9

button or the

K

button on the remote. You can change the value of

the selected option by pressing the - or + buttons on the front panel or the

up/down/left/right

C

arrow buttons on the remote. Step through the

sub-menus by pressing the MENU

9

button on the front panel or the

K

button on the remote.

• TONE BYPASS: TONE BYPASS on/off (For more information refer to Tone

Control Bypass section).

NOTE: This setting is stored permanently even after the A14 is powered

off.

• BASS: BASS level can be changed to desired settings. (For more information

refer to Bass and Treble Control section.)

NOTE: This setting is stored permanently even after the A14 is powered

off.

• TREBLE: TREBLE level can be changed to desired settings. (For more

information refer to Bass and Treble Control section.)

NOTE: This setting is stored permanently even after the A14 is powered

off.

• BALANCE: Change left/right balance. (For more information refer to

Balance Control section.)

NOTE: This settings is stored permanently even after the A14 is

powered off.

• DIMMER: Dims the front display.

NOTE: This setting is stored permanently even after the A14 is powered

off.

• LED DIMMER: Dims the Power LED and the LEDs above the Speaker Selector

buttons on the front panel.

NOTE: This setting is stored permanently even after the A14 is powered

off.

• POWER ON MAX VOL: This sets the maximum volume level when the unit

is turned on. “45” is the factory default.

NOTE: Power On Max Volume settings do not apply to sources

configured with Fixed Gain.

• POWER MODE: Enables the A14 to be controlled via the network port

when attached to an automation system. The power consumption is higher

in Quick Power mode. If network control is not required select the Normal

Power mode. “Normal” is the factory default.

Valid settings include: Quick, Normal.

NOTE: When the POWER MODE is configured to Quick, the A14 will

consume additional power in standby mode.

NOTE:: Some regions limit the amount of Standby Power Consumption

allowed and the POWER MODE will not be available. To control the

Rotel product in this case use the RS232 connection. For questions

on the availablity of the Power Mode please contact your authorized

Rotel dealer.

• USB POWER: This option allows the rear panel USB connector to provide

power, even when the A14 is in standby mode.

To enable the continuous power mode select the ALWAYS option. To provide

power only when the A14 is powered on, select the NORMAL option. The

default for USB POWER is set to NORMAL.

NOTE: The front panel power button must be in the ON position to

supply power to the rear panel USB connector.

NOTE: When the USB POWER is configured to ALWAYS the A14 will

consume additional power in standby mode to supply USB power.

• OFF TIMER: The A14 can be congured to automatically power off if

unused for a specied period. If no changes are made to the unit within

the specied “Off Timer” period, the unit will automatically go to STANDBY

mode. The auto power off timer will be restarted if changes are made to

the volume, source or playback. The default for Off Timer is set to DISABLE.

Valid settings include: DISABLE, 1 HOUR, 2 HOURS, 5 HOURS, 12 HOURS.

16

A14 Stereo Integrated Amplier

NOTE:: Some regions require the Off Timer default setting to be

20 minutes. This can be changed in the SETUP MENU to any of the

available options. For questions about the Off Timer settings please

contact your authorized Rotel dealer.

NOTE:: Some products cannot detect ANALOG signal inputs and

the unit may power off if there is no digital audio source detected or

user action with the remote control or front panel. Analog input signal

detection is not available in all models which may cause the unit to

inadvertently power off. In this case the Off Timer should be set to

DISABLED.

• SIGNAL SENSE: Check if a digital audio signal is present on the congured

Signal Sense input. When this input is selected as the active listening

source, the A14 monitors the digital data stream to determine if there is

audio. If there is no audio detected for 10 minutes, the A14 will enter

Signal Sense Standby Mode. When in Signal Sense Standby Mode and

the A14 detects audio on Signal Sense input, the unit will automatically

power on. To disable this function, select the OFF option which is the

factory default setting.

NOTE: Recent software versions allow the configured Signal Sense

input to be active in Standby Mode regardless of source input active

when the unit was powered off to standby. Previous version of software

required the Signal Sense configured input to be the active source when

the unit was powered off for Signal Sense to become active and monitor

the configured input for audio. For more information and details on

supported software versions and software update steps please contact

your authorized Rotel dealer.

NOTE: When the SIGNAL SENSE function is activated the A14 will

consume additional power in signal sense standby mode.

• FIXED GAIN: Congures a Fixed Volume level for a specied input. To

enable this feature, select the desired xed volume level for AUX1, AUX2,

USB, PC-USB, Optical 1, Optical 2, Coax 1, Coax 2, or Bluetooth. When

enabled and the input with a Fixed Volume is selected, the Volume level

will immediately be set to the specied level.

Valid settings include: VARIABLE, FIXED MIN, FIXED 01-95, FIXED MAX.

• AUX1 VOL: VARIABLE (disabled) is factory default.

• AUX2 VOL: VARIABLE (disabled) is factory default.

• USB VOL: VARIABLE (disabled) is factory default.

• PC-USB VOL: VARIABLE (disabled) is factory default.

• OPT1 VOL: VARIABLE (disabled) is factory default.

• OPT2 VOL: VARIABLE (disabled) is factory default.

• COAX1 VOL: VARIABLE (disabled) is factory default.

• COAX2 VOL: VARIABLE (disabled) is factory default.

• BTOOTH VOL: VARIABLE (disabled) is factory default.

NOTE: The Volume knob on the front panel and Volume +/- buttons

on the IR remote are disabled when the volume is Fixed. To disable this

feature set the Fixed Volume level to “Variable”.

• PC-USB CLASS: Change supported PC-USB Audio Class of the attached

device.

NOTE: Some computers attached to the PC-USB do not support USB

Audio Class 2.0 and do not support 32/384 audio playback. If needed

the PC-USB can be configured for USB Audio Class 1.0. Please refer

to your computer operating system for details.

• VIEW NETWORK: Shows the network connection status and to view

the network settings. To view the network settings, press the + button on

the front panel or the ENT button on the remote control. If the network is

properly congured and attached, “Connected” will be displayed. To view

additional network conguration details, including IP Address information,

press the MENU button to toggle through the settings.

• CONFIGURE NETWORK: Allows conguration of the network IP settings.

To enter the Network Conguration menu option press the + button on the

front panel or the ENT button on the remote control.

NOTE: Configuration of the network requires the use of the remote

control to enter the IP address details. This setup cannot be completed

using the front panel controls. Please ensure you have access to the

remote control before proceeding with Network Configuration.

To begin conguration of the network, press the ENT button on the remote

control and follow as below:

The A14 supports both DHCP and STATIC IP addressing. Select the desired

IP address method with the left/right arrow buttons on the remote control

and press ENT to conrm.

If DHCP is selected, the A14 will refresh the IP address after pressing the ENT

button on the remote control to conrm. The refresh process could take up

to 10 seconds. The display will indicate if the DHCP refresh was successful.

If the refresh process failed, check the network connections and try again

by pressing the ENT button on the remote control. To exit the DHCP refresh

process, press the MENU button.

If STATIC IP address mode is selected, you must congure all settings for the

network, including IP Address, Subnet Mask, Gateway and DNS Server.

Use the up/down arrow buttons on the remote control to adjust the values

and press the left/right buttons on the remote control to move to the next

section. When the proper IP information is congured press ENT to conrm.

NOTE: For more information regarding network connection please

contact your authorized Rotel dealer.

NOTE: A network connection is not required for the A14 to operate.

• S/W VERSION: This shows the current software version loaded into the

A14. The software can be updated if the A14 is properly connected to

the Internet.

• Press the “+” button on the front panel to check if a new software

version is available.

17

• If a new software version is available, press the “+” button on the

front panel, to begin the software update process.

• The new software will be downloaded from the Internet. The A14

will power cycle when the software update is complete.

NOTE: Do NOT power off the A14 during the software update process.

NOTE: It is recommended to Reset Factory Defaults after the software

update is complete.

• PC-USB VERSION: This shows current loaded software version for PC-USB

processor.

• FACTORY DEFAULT: This sets the unit back to the original state as when it

left the factory. Press the “+” button on the front panel or the ENT button

on the remote control to enter factory reset setting. And then press the “+”

button or ENT again to begin reset, or press the MENU button to cancel.

NOTE: All previously configured options will be erased and reset to

the factory default settings.

Troubleshooting

Most difculties in audio systems are the result of incorrect connections, or

improper control settings. If you encounter problems, isolate the area of the

difculty, check the control settings, determine the cause of the fault and

make the necessary changes. If you are unable to get sound from the unit,

refer to the suggestions for the following conditions:

Power Indicator Is Not Illuminated

The Power Indicator and the basic items in the Display window should be

illuminated whenever the unit is plugged into the wall power outlet and the

Power button is pushed in. If it does not illuminate, test the power outlet with

another electrical device, such as a lamp. Be sure the power outlet being

used is not controlled by a switch that has been turned off.

Fuse Replacement

If another electrical device works when plugged into the power outlet, but

the Power Indicator still will not illuminate when the unit is plugged into

the wall outlet, it indicates that the internal power fuse may have blown.

If you believe this has happened, contact your authorized Rotel dealer to

get the fuse replaced.

No Sound

Check the signal source to see if it is functioning properly. Make sure the

cables from the signal source to the amplier inputs are connected properly.

Be sure the Input Source is set to the proper input. Check the wiring between

the amplier and the speakers.

Playable Audio Formats

USB Apple (iPhone, iPod, iPad)

Format Notes

Any supported file

loaded to Apple device.

Any supported le loaded to Apple device. Phone may

resample depending on stored format. May exclude

Apps designed to play formats not originally supported

by the sending device.

APTX Bluetooth

Format Notes

Any format supported

by the sending device.

May exclude Apps designed to play formats not originally

supported by the sending device.

PC-USB

Format Notes

Format determined

by the Media Player/

Server software that

you use.

Any supported format by the PC software

PCM Audio:

44.1k, 48k, 88.2k, 96k, 176.4k, 192k, 384k

(16 bit, 24 bit and 32 bit)

DSD64 and DSD128

Coax/Optical

Format Notes

SPDIF LPCM

44.1k, 48k, 88.2k, 96k, 176.4k, 192k

16 bit, 24 bit

Cannot Connect via Bluetooth

If you cannot pair your Bluetooth enabled device to the A14, delete the

memory of the previous connection on your device. On your device this is

often listed as “Forget this Device”. Then try to make the connection again.

18

A14 Stereo Integrated Amplier

“Made for iPod,” and “Made for iPhone,” means that an electronic accessory

has been designed to connect specically to iPod or iPhone, respectively, and

has been certied by the developer to meet Apple performance standards.

Apple is not responsible for the operation of this device or its compliance with

safety and regulatory standards. Please note that the use of this accessory

with iPod, or iPhone may affect wireless performance.

iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of

Apple Inc., registered in the U.S. and other countries.

Specications

Continuous Power Output 80 watts/ch

(20 - 20k Hz, < 0.03%, 8 ohms)

Total Harmonic Distortion (20 Hz - 20k Hz, 8 ohms) < 0.03%

Intermodulation Distortion (60 Hz : 7k Hz, 4:1) < 0.03%

Frequency Response

Phono Input 20 Hz - 20k Hz, ± 0.5 dB

Line Level Inputs 10 Hz - 100k Hz, ± 0.5 dB

Damping Factor (20 - 20,000 Hz, 8 ohms) 220

Input Sensitivity / Impedance

Phono Input 3.4 mV / 47k Ohms

Line Level Inputs 230 mV / 24k Ohms

Input Overload

Phone Input 50 mV

Line Level Inputs 4 V

Preamp Output / Impedance 1.2 V / 470 Ohms

Tone Controls - Bass / Treble ± 10 dB at 100 Hz / 10k Hz

Signal to Noise Ratio (A weighting)

Phono Input 90 dB

Line Level Inputs 100 dB

Digital Section

Frequency Response 10Hz - 80k Hz (± 3.0dB,MAX)

Signal to Noise Ratio (A weighting) 103 dB

Input Sensitivity/Impedance 0 dBfs/75 ohms

Preamplifier Output Level 1.3 V (at - 20dB)

Digital Inputs SPDIF LPCM

(up to 192k Hz 24 bit)

PC-USB USB Audio Class 1.0

(up to 96kHz 24bit)

USB Audio Class 2.0

(up to 384kHz 32bit)*

*Driver installation required

DSD and DoP support

General

Power Requirements

USA 120V, 60 Hz

EC 230V, 50 Hz

Standby Power Consumption < 0.5W

Power Consumption 280 Watts

BTU (4 ohms, 1/8th power) 632 BTU/h

Rear USB Output 5 V / 0.5 A

Dimensions (W, H, D) 430 x 93 x 345 mm

17” x 3

5

/8” x 13

1

/2”

Panel Height 80 mm / 3

1

/8”.

Weight (net) 8.2 kg, 18 lbs.

All specications are accurate at the time of printing.

Rotel reserves the right to make improvements without notice.

Rotel and the Rotel HiFi logo are registered trademarks of The Rotel Co., Ltd.

Tokyo, Japan.

PB 19

A14 Amplicateur Stéréo Intégré

Remarque

La prise RS232 ne doit être utilisée que par une personne qualifiée.

ATTENTION : Il n’y a à l’intérieur aucune pièce susceptible d’être modifiée

par l’utilisateur. Adressez-vous impérativement à une personne qualifiée.

ATTENTION : Pour réduire tout risque d’électrisation ou d’incendie, ne

pas exposer l’appareil à une source humide, ou à tout type de risque

d’éclaboussure ou de renversement de liquide. Ne pas poser dessus

d’objet contenant un liquide, comme un verre, un vase, etc. Prenez

garde à ce qu’aucun objet ou liquide ne tombe à l’intérieur de l’A14

par ses orifices de ventilation. Si l’appareil est exposé à l’humidité ou

si un objet tombe à l’intérieur, débranchez-le immédiatement de son

alimentation secteur, et adressez-vous immédiatement et uniquement

à une personne qualifiée et agréée.

Tous les conseils de sécurité et d’installation doivent être lus.

Conservez soigneusement ce livret.

Tous les conseils de sécurité doivent être soigneusement respectés.

Respectez les procédures d’installation et de fonctionnement indiquées

dans ce manuel.

Ne pas utiliser cet appareil près d’un point d’eau.

L’appareil doit être nettoyé uniquement avec un chiffon sec ou un

aspirateur.

Il ne doit pas être posé sur un fauteuil, un canapé, une couverture ou

toute autre surface susceptible de boucher ses ouïes d’aération ; ou

placé dans un meuble empêchant la bonne circulation d’air autour des

orifices d’aération.

Cet appareil doit être placé loin de toute source de chaleur, tels que

radiateurs, chaudières, bouches de chaleur ou d’autres appareils

produisant de la chaleur.

Notamment, ne pas tenter de supprimer la prise de terre (troisième broche

de la prise) si celle-ci est présente. Si la prise n’est pas conforme à celles

utilisées dans votre installation électrique, consultez un électricien agréé.

Prendre garde à ce que ce cordon d’alimentation ne soit pas pincé,

écrasé ou détérioré sur tout son trajet, et à ce qu’il ne soit pas mis en

contact avec une source de chaleur. Vérifiez soigneusement la bonne

qualité des contacts, à l’arrière de l’appareil comme dans la prise murale.

N’utilisez que des accessoires préconisés par le constructeur.

N’utilisez que des meubles, supports, systèmes de transport

suffisamment solide pour supporter l’appareil. Procédez

toujours avec la plus extrême précaution lorsque vous

déplacez l’appareil, afin d’éviter tout risque de blessure

ou des dommages à l’appareil.

Débranchez le câble d’alimentation en cas d’orage, ou si l’appareil ne

doit pas être utilisé pendant une longue période.

L’appareil doit être immédiatement éteint, débranché puis retourné au

service après-vente agréé dans les cas suivants :

le câble d’alimentation

secteur ou sa prise est endommagé; un objet est tombé, ou du liquide

a coulé à l’intérieur de l’appareil; l’appareil a été exposé à la pluie;

l’appareil ne fonctionne manifestement pas normalement; l’appareil

est tombé, ou le coffret est endommagé.

L’appareil doit être utilisé dans un climat non tropical.

Tous les appareils Rotel sont conçus en totale

conformité avec les directives internationales

concernant les restrictions d’utilisation de substances

dangereuses (RoHS) pour l’environnement, dans

les équipements électriques et électroniques, ainsi

que pour le recyclage des matériaux utilisés (WEEE,

pour Waste Electrical and Electronic Equipment).

Le symbole du conteneur à ordures barré par une

croix indique la compatibilité avec ces directives, et

le fait que les appareils peuvent être correctement

recyclés ou traités dans le respect total de ces normes.

Ce symbole signifie que cet appareil bénéficie d’une

double isolation électrique. Le branchement d’une

mise à la masse ou à la terre n’est pas nécessaire.

Remarques importantes concernant la sécurité

Vous devez réserver un espace libre d’une dizaine de

centimètres minimum autour de l’appareil.

ATTENTION : La prise d’alimentation située à l’arrière constitue le

principal moyen pour déconnecter l’appareil du secteur. Cet équipement

doit être positionné dans un espace ouvert qui permet de garder l‘accès

au câble d’alimentation.

Cet appareil doit être branché sur une prise d’alimentation secteur, d’une

tension et d’un type conformes à ceux qui sont indiqués sur la face arrière

de l’appareil (USA : 120 V/60 Hz, CE : 230 V/50 Hz).

Brancher l’appareil uniquement grâce au cordon secteur fourni, ou à

un modèle équivalent. Ne pas tenter de modifier ou changer la prise.

Ne pas utiliser de cordon rallonge.

La prise d’alimentation secteur constitue le moyen radical de déconnexion

de l’appareil. Elle doit donc rester en permanence accessible, car sa

déconnexion constitue la seule assurance que l’appareil n’est plus

alimenté par le secteur.

Utilisez uniquement des câbles de Classe 2 pour réalise les connexions aux

enceintes acoustiques et offrant une isolation suffisante pour minimiser

les risques de chocs électriques.

Les piles de la télécommande infra-rouge ne doivent en aucun cas

exposées à une chaleur excessive notamment au feu ou au soleil

direct. Les batteries doivent être recyclées ou éliminées selon les

directives nationales et locales.

POWER

PHONES

A12

PHONO TUNER CD USB OPT COAX AUX PC-USB BT

5V / 2.1A

MENU

SPEAKERS

A B

POWER

PHONES

A14

PHONO TUNER CD USB OPT COAX AUX PC-USB BT

5V

/

2.1A

MENU

SPEAKERS

A B

L’éclair dans un triangle équilatéral indique

la présence interne de tensions électriques

élevées susceptibles de présenter des

risques graves d’électrocution.

Le point d’exclamation dans un triangle

équilatéral indique à l’utilisateur la

présence de conseils et d’informations

importantes dans le manuel d’utilisation

accompagnant l’appareil. Leur lecture est

impérative.

20

A14 Amplicateur Stéréo Intégré

A propos de Rotel

Notre histoire commence il y a environ 50 ans. Depuis, au l des années,

nous avons reçu des centaines de prix et de récompenses, et satisfait des

centaines de milliers de personnes – comme vous !

Rotel a été fondée par une famille passionnée de musique, qui a décidé de

fabriquer des maillons Haute Fidélité sans compromis aucun.

Depuis sa création, cette passion est restée intacte, et cette famille s’est

xée comme objectif de proposer à tous les audiophiles et mélomanes

les meilleurs appareils possibles, quel que soit leur budget. Une volonté

partagée par tous les employés de Rotel.

Les ingénieurs Rotel travaillent comme une équipe très soudée, écoutant,

peaunant chaque nouveau modèle jusqu’à ce qu’il atteigne exactement

leurs standards – très élevés – de musicalité. Ils sont libres de choisir des

composants en provenance du monde entier, an de concevoir le meilleur

produit possible. C’est ainsi que vous trouverez dans nos appareils des

condensateurs d’origine britannique ou allemande, des transistors japonais

ou américains, tandis que les transformateurs toriques sont toujours fabriqués

dans nos propres usines Rotel.

Nous sommes tous concernés par la qualité de l’environnement. Et, comme de

plus en plus de produits électroniques sont fabriqués puis éliminés quelques

années plus tard, il est désormais essentiel qu’un constructeur fabrique tous

ses produits en veillant à ce qu’ils aient un impact minimum sur la planète.

Chez Rotel, nous sommes très ers d’apporter notre pierre à ce nouvel édice.

Nous avons réduit la teneur en plomb de nos électroniques, en utilisant

notamment des composants et une soudure spéciale ROHS. Nos ingénieurs

travaillent en permanence pour améliorer le rendement des alimentations de

puissance sans compromettre leur qualité. C’est ainsi qu’en mode Standby,

les appareils Rotel consomment moins pour se conformer aux exigences

de la « Standby Power Consumption » qui limite la consommation en veille

des appareils électroniques.

L’usine Rotel participe également de façon active à la protection de

l’environnement au travers d’un processus de fabrication général amélioré

et toujours plus écologique et plus propre.

Tous les membres de l’équipe Rotel vous remercient pour l’achat de cet

appareil. Nous sommes persuadés qu’il vous offrira de nombreuses années

d’intense plaisir musical.

Mise en route

Merci d’avoir acheté cet Amplicateur Stéréo Intégré Rotel A14. Associé

à un ensemble audio de qualité, il vous offrira de nombreuses années de

plaisir musical.

Cet amplicateur est un élément hautes performances doté de fonctionnalités

avancées. Tous les aspects de sa conception ont été optimisés pour garantir

une dynamique sans faille et restituer les nuances les plus subtiles de votre

musique. L’appareil dispose d’une alimentation hautement régulée intégrant

un transformateur de puissance toroïdal spéciquement conçu par Rotel. Cette

alimentation basse impédance dispose de réserves d’énergie importantes

et permet à l’amplicateur de prendre facilement en charge tous les types

de signaux audio, même les plus exigeants. Ce type de composant est plus

cher à fabriquer, mais il est d’une qualité supérieure sur le plan musical.

Sommaire

Figure 1 : Commandes et Branchements 3

Figure 2 : Télécommande RR-AX1400 4

Figure 3 : Entrées préampli et sorties pour enceintes acoustiques 5

Figure 4 : Branchements Entrées numériques 6

Figure 5 : Branchements Rotel Link et trigger 12 V 7

Figure 6 : Entrée USB en face avant 8

Remarques importantes 9

Remarques importantes concernant la sécurité ............................19

A propos de Rotel .................................................20

Mise en route ....................................................20

Quelques précautions préalables 21

Installation 21

Câbles 21

Télécommande infrarouge RR-AX1400 ...................................21

Code secondaire de télécommande 21

Piles de la télécommande 21

Alimentation secteur et commandes .....................................22

Prise secteur

s

22

Interrupteur de mise sous tension/veille Standby

1A

et indicateur Power

2

22

Branchement trigger 12 V

u

22

Indicateur de protection

2

..........................................22

Connexions d’entrée du signal ........................................22

Entrée Phono

-

et connexion à la masse [GND]

0

22

Entrées Lignes

=qw

22

Entrées Numériques

]

23

Sortie Préampli

[

................................................23

Sorties pour enceintes acoustiques

\a

................................23

Commutateur de sélection des enceintes acoustiques

5

23

Choix des enceintes acoustiques 23

Choix des câbles d’enceintes acoustiques 23

Polarité et Phase 23

Branchement des enceintes 23

Sortie Casque

4

.................................................23

Afcheur

6

.....................................................23

Entrée USB en face avant

3

.........................................24

Connexion Bluetooth APTX

e

........................................24

Port USB en face arrière

p

..........................................24

Commandes Audio .................................................24

Contrôle de volume

7E

24

Réglage de balance

9B

24

Activation/désactivation du contrôle de tonalité

9B

24

Ajustements Graves/Aigus

9B

24

Le sélecteur d’entrée de source

8I

24

Contrôle de luminosité de l’afchage ...................................25

Luminosité de l’écran

9D

25

Luminosité des LED

9

25

Entrée pour PC-USB

r

.............................................25

ROTEL LINK

t

...................................................25

Prise jack pour télécommande externe (EXT REM IN)

y

.....................25

Prise RS232

i

..................................................25

Connexion réseau

o

...............................................26

Menu de conguration ..............................................26

Problèmes de fonctionnement .........................................28

L’indicateur de mise sous tension n’est pas allumé 28

Remplacement du fusible 28

Pas de son 28

Formats de lecture compatibles 28

Pas de connexion via Bluetooth 28

Spécications ....................................................29

La pagina sta caricando ...

Rotel A14 Manuale del proprietario

Rotel A14 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti