Haier 1U12BS1ERA Manuale del proprietario

Please read this manual carefully before installtion.

●

Keep this operation manual for future reference.

1U12BS1ERA

1U09BS1ERA

1U07BS1ERA

1U18FS1ERA

1U24GS1ERA

INSTALLATION MANUAL

ROOM AIR CONDITIONER

NO.0010535386

14

1

2

9

Indoor/Outdoor Unit Installion Drawings

Safety Precautions

Installation Procedure

Outdoor Unit Troubleshooting

Read Before Installation

6

Contents

Contenido

Unidad interior y exterior Dibujos de extracción

15

Precauciones de seguridad 16

Leer antes de realizar la instalación 20

Procedimiento instalación 23

Unidad interior Resolución de problemas

28

Indice

Unità esterna/interna Immagini per l'installazione

29

Precauzioni di sicurezza

30

Leggere prima dell'installazione

34

Processo di installazione

37

Unità esterna Risoluzione dei problemi

42

Table des matières

Unité intérieure/extérieure Schémas d'installation

43

Consignes de sécurité

À lire avant l'installation

Procédure d'installation

Unité extérieure Dépannage

56

44

48

51

Haier Industrial Park, No.1 Haier Road, Qingdao, P.R.China

CE

All the products are in conformity with the following

European provision:

- Low Voltage Directive 73/23/EEC

- Low Voltage Directive 2006/95/EC

-Electomagnetic CompatibilitY 89/336/EEC

-Electomagnetic CompatibilitY 2004/108/EC

ROHS

The products are fulfilled with the requirements in the

directive 2002/95/EEC of the European parliament and of

council on the Restriction of the use of Certain Hazardous

Substances in Electrical and Electronic Equipment (EU

RoHS Directive)

WEEE

DISPOSAL REQUIREMENTS:

Your air conditioning product is marked with this

symbol.This means that electrical and electronic

products shall not be mixed with unsorted

household waste. Do not try to dismantle the

system yourself : the dismantling of the air

EUROPEAN REGULATIONS

CONFORMITY FOR THE MODELS

1

1+2=

kg

R410A

2

kg

2=

1=

B

C

D

FE

kg

A

This product contains fluorinated greenhouse gases covered

by the Kyoto Protocol. Do not vent into the atmosphere.

Refrigerant type:R410A

GWP* value:1975

GWP=global warming potential

Please fill in with indelible ink,

• 1 the factory refrigerant charge of the product

• 2 the additional refrigerant amount charged in the field

and

• 1+2 the total refrigerant charge

on the refrigerant charge label supplied with the product.

The filled out label must be adhered in the proximity of the

product

charging port (e.g. onto the inside of the stop value

A contains fluorinated greenhouse gases covered by the

Kyoto

Protocol

B factory refrigerant charge of the product: see unit name

plate

C additional refrigerant amount charged in the field

D total refrigerant charge

E outdoor unit

F refrigerant cylinder and manifold for charging

IMPORTANT INFORMATION REGA-

RDING THE REFRIGERANT USED

In accordance with the directive 2002/96/CE of the European

parliament, herewith we inform the consumer about the dis-

posal requirements of the electrical and electronic products.

conditioning system,treatment of the refrigerant, of oil and of

other part must be done by a qualified installer in

accordance

with relevant local and national legislation. Air conditioners

must be treated at a specialized treatment facility for reuse,

recycling and recovery. By ensuring this product is disposed

of correctly, you will help to prevent potential negative cons-

equences for the environment and humen health. Please

contact the installer or local authority for more information.

Battery must be removed from the remote controller and dis-

posed of separately in accordance with relevant local and

nationl legislation.

Contains fluorinated greenhouse gases

covered by the Kyoto Protocol

cover).

Please be subject to the actual product purchased.

The above indoor and outdoor units’ picture is just for your reference.

F

A

C

E

D

Optional parts for piping

Non-adhesive tape

Adhesive tape

Saddle(L.S)withscrews

Connecting electric cable

for indoor and outdoor

Drain hose

Heating insulating material

Piping hole cover

Fixing of outdoor unit

Fix the unit to concrete or blockƽ

with bolts (10mm) and nuts ﬁrmly

and horizontally.

When ﬁtting the unit to wall

ƽ

surface,rooforrooftop,ﬁx

asupportersurelywithnails

or wires in consideration of

earthquake and strong wind.

If vibration may affect the

ƽ

house, ﬁx the unit by attaching a

vibration-proof mat.

The marks from to

in the ﬁgure are the

parts numbers.

Thedistancebetween

theindoorunitandthe

ﬂoor should be more

than 2m.

ThemodelsadoptHFCfreerefrigerantR410A.

more than

10cm

more than 15cm

more than 10cm

more than 20cm

more than

20cm

more than 25cm

more than

60cm

A

G

ƽ

A

F

C

E

D

G

B

Arrangement of piping

directions

Rear left

Left

Rear

right

Right

Below

G

Attention must be paid to

the rising up of drain hose

Indoor/Outdoor Unit Installation Drawings

For installation of the indoor units,refer to the installation manual which was provided with the units.

(The diagram shows a wall-mounted indoor unit.)



AIR OUTLET

AIR INLET

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

4

ƽ

Compressor(Inside of Unit)

1

WARNING

CAUTION

2

Have the unit professionally installed.

Improper installation by an unqualified person may result

in water leak, electric shock, or fire.

Be sure to carefully follow each step in this handbook when

installing the unit.

Improper installation may result in water leak, electric shock,

smoke or fire.

Have all electrical work performed by a licensed electrician

according to the local regulations and the instructions given

in this manual. Secure a circuit designated exclusively to

the unit.

Improper installation or a lack of circuit capacity may cause

the unit to malfunction or present a risk of electric shock,

smoke,and fire.

Place the unit on a stable, level surface that withstands the

weight of the unit to prevent the unit from tipping over or

falling causing injury as a result.

Only use specified cables for wiring. Securely connect each

cable, and make sure that the cables are not straining the

terminals.

Cables not connected securely and properly may generate

heat and cause fire.

Take necessary safety measures against typhoons and

earthquakes to prevent the unit from falling over.

Do not make any changes or modifications to the unit. In

case of problems, consult the dealer.

If repairs are not made properly, the unit may leak water

and present a risk of electric shock, or it may produce smoke

or cause fire.

Securely attach the terminal cover(panel) on the unit.

If installed improperly, dust and/or water may enter the unit

and present a risk of electric shock, smoke or fire.

Only use refrigerant R410A as indicated on the unit when

installing or relocating the unit.

The use of any other refrigerant or an introduction of air into

the unit circuit may cause the unit to run an abnormal cycle

and abnormal cycle and cause the unit to burst.

In the event of a refrigerant gas leak, provide adequate

ventilation to the room.

If leaked refrigerant gas is exposed to a heat source, noxious

gases may form.

Do not touch the fins on the heat exchanger with bare hands,

for they are sharp and dangerous.

Do not try to defeat the safety features of the devices, and

do not change the settings.

Defeating the safety features on the unit such as the pressure

switch and temperature switch or using parts other than the

dealer or specialist may result in fire or explosion.

When installing the unit in a small room, safeguard against

hypoxia that results from leaked refrigerant reaching the

threshold level.

Consult the dealer for necessary measures to take.

When relocating the air conditioner, consult the dealer or

a specialist.

Improper installation may result in water leak, electric shock,

or fire.

After completing the service work, check for a refrigerant

gas leak.

If leaked gas refrigerant is exposed to a heat source such

as fan heater,stove,and electric grill, noxious gases may

form.

Only use specified parts.

Have the unit professionally installed. Improper installation

may cause water leak, electric shock,smoke, or fire.

With All-Fresh type air conditioners, outdoor air may be

directly blown into the room upon thermo off. Take this into

consideration when installing the unit.

Direct exposure to outdoor air may present a health hazard,

and it may also cause food items to deteriorate.

WARNING

Safety Precautions

3

Precautions for Handling Units for Use with R410A

Do not use the existing refrigerant piping

The old refrigerant and refrigerator oil in the existing piping

contain a large amount of chlorine, which will cause the

refrigerator oil in the new unit to deteriorate.

R410A is a high-pressure refrigerant, and the use of the

existing piping may result in bursting.

Keep the inner and outer surfaces of the pipes clean and

free of contaminants such as sulfur, oxides, dust/dirt shaving

particles,oils,and moisture.

Contaminants inside the refrigerant piping will cause the

refrigerant oil to deteriorate.

Use a vacuum pump with a reverse-flow check valve.

If other types of valves are used, the vacuum pump oil will

flow back into the refrigerant cycle and cause the refrigerator

oil to deteriorate.

Do not use the following tools that have been used with the

conventional refrigerants. Prepare tools that are for exclusive

use with R410A.

(Gauge manifold, charging hose, gas leak detector,

reverse-flow check valve, refrigerant charge base,vacuum

gauge, and refrigerant recovery equipment.)

If refrigerant and/or refrigerant oil left on these tools are

mixed in with R410, or if water is mixed with R410A, it will

cause the refrigerant to deteriorate.

Since R410A does not contain chlorine, gas-leak detectors

for conventional refrigerators will not work.

Store the piping to be used during installation indoors, and

keep both ends of the piping sealed until immediately before

brazing.(keep elbows and other joints wrapped in plastic.)

If dust, dirt, or water enters the refrigerant cycle, it may

cause the oil in the unit to deteriorate or may cause the

compressor to malfunction.

A large amount of mineral oil will cause the refrigerating

machine oil to deteriorate.

Use a small amount of ester oil, ether oil, or alkylbenzene

to coat flares and flange connections.

Use liquid refrigerant to charge the system.

Charge the unit with gas refrigerant will cause the refrigerant

in the cylinder to change its composition and will lead to

a drop in performance

Do not use a charging cylinder.

The use of charging cylinder will change the composition

of the refrigerant and lead to power loss.

Exercise special care when handling the tools.

An introduction of foreign objects such as dust, dirt or

water into the refrigerant cycle will cause the refrigerating

machine oil to deteriorate.

Only use R410A refrigerant.

The use of refrigerants containing chlorine(i.e. R22) will

cause the refrigerant to deteriorate.

Before Installing the Unit

Do not install the unit in a place where there is a possibility

of flammable gas leak.

Leaked gas accumulated around the unit may start a fire.

Do not use the unit to preserve food, animals, plants, artifacts,

or for other special purposes.

The unit is not designed to provide adepuate conditions

to preserve the quality of these items.

Do not use the unit in an unusual environment

The use of the unit in the presence of a large amount of

oil, steam, acid, alkaline solvents or special types of sprays

may lead to a remarkable drop in performance and/or

malfunction and presents a risk of electric shock, smoke,

or fire.

The presence of organic solvents, corroded gas (such as

ammonia,sulfur compounds,and acid may cause gas or

water leak.)

When installing the unit in a hospital, take necessary measures

against noise.

High-frequency medical equipment may interfere with the

normal operation of the air conditioning unit or the air

conditioning unit may interfere with the normal operation

of the medical equipment

When humidity level exceeds 80% or when the drainage

system is clogged, indoor units may drip water.

Installation of a centralized drainage system for the outdoor

unit may also need to be considered to prevent water drips

from the outdoor units.

Do not place the unit on or over things that may not get wet.

Caution

Safety Precautions

4

Before Installing (Relocating) the Unit or Performing Electric Work

Ground the unit.

Do not connect the grounding on the unit to gas pipes,water

pipes, lightning rods, or the grounding terminals of

telephones. Improper grounding presents a risk of electric

shock, smoke, fire, or the noise caused by improper

grounding may cause the unit to malfunction.

Before the Test Run

Do not operate switches with wet hands to avoid electric.

Allow for at least five minutes before turning off the unit,

otherwise the unit may leak water or experience other

problems.

Do not turn off the power immediately after stopping the unit.

If the wires are too taut, they may break or generate heat

and/or smoke and cause fire.

Make sure the wires are not subject to tension.

Install a breaker for current leakage at the power source

to avoid the risk of electric shock.

Without a breaker for current leakage, there is a risk of

electric shock, smoke or fire.

Use breakers and fuses (electrical current breaker, remote

switch<switch+Type-B fuse>,molded case circuit breaker)

with a proper current capacity.

The use of large-capacity fuses, steel wire, or copper wire

may damage the unit or cause smoke or fire.

When installing draining pipes, follow the instructions in the

manual, and make sure that they properly drain water so as

to avoid dew condensation.

If not installed properly, they may cause water leaks and

damage the furnishings.

Do not spray water on the air conditioners or immerse the

air conditioners in water.

Water on the unit presents a risk of electric shock.

Periodically check the platform on which is placed for damage

to prevent the unit from falling.

If the unit is left on a damaged plarform, it may topple over,

causing injury.

Things such as nails may be included in the package.

Dispose of them properly to prevent injury.

Plastic bags present a choking hazard to children. Tear

up the plastic bags before disposing of them to prevent

accidents.

Properly dispose of the packing materials.

Do not touch the refrigerant pipes with bare hands during

and immediately after operation.

Depending on the state of the refrigerant in the system,

certain parts of the unit such as the pipes and compressor

may become very cold or hot and may subject the person

to frost bites or burning.

Do not operated the unit without panels and safety guards

in their proper places.

They are there to keep the users from injury from

accidentally touching rotating, high-tempreture or high-

voltage parts.

Dust particles in the air may clog the system and cause

malfunction.

Do not operate the unit without air filters.

Caution

Safety Precautions

5

Read Before Installation

Tools/Materials Use Notes

Gauge Manifold Evacuating,refrigerant charging 5.09MPa on the High-pressure side.

Charging Hose Evacuating, refrigerant charging Hose diameter larger than the concentional ones.

Refrigerant Recovery Equipment Refrigerant recovery

Refrigerant Cylinder Refrigerant charging Write down the refrigerant type. Pink in color at the top of the cylinder.

Refrigerant Cylinder Charging Port Refrigerant charging Hose diameter larger than the conventional ones.

Flare Nut Connecting the unit to piping Use Type-2 Flare nuts.

Tools/Materials Use Notes

Gas leak detector Detection of gas leaks The ones for HFC type refrigerant may be used.

Vacuum Pump Vacuum drying May be used if a reverse flow check adaptor is attached.

Refrigerant Recovery Equipment Recovery of refrigerant May be used if designed for use with R410A.

Flare Tool Flare machining of piping Chages have been made in the flare machining dimension.Refer to the next page.

Tools/Materials Use Notes

Vacuum Pump with a Check Valve Vacuum drying

Bender Bending pipes

Pipe Cutter Cutting pipes

Torque Wrench Tightening flare nuts Only 12.70 (1/2'') and 15.88(5/8'') have a larger flare machining dimension.

Welder and Nitrogen Cylinder Welding pipes

Refrigerant Charging Meter Refrigerant charging

Vacuum Gauze Checking vacuum degree

Tools/Materials Use Notes

Charging Cylinder Refrigerant Charging Must not be used with R410-type units.

CAUTION

Items to Be Checked

(1). Verify the type of refrigerant used by the unit to be serviced. Refrigerant Type: R410A

(2). Check the symptom exhibited by the unit to be serviced. Look in this service handbook for symptoms relating to the

refrigerant cycle.

(3). Be sure to carefully read the safety precautions at the beginning of this document.

(4). If there is a gas leak or if the remaining refrigerant is exposed to an open flame, a noxious gas hydrofluoric acid may

form. Keep workplace well ventilated.

Install new pipes immediately after removing old ones to keep moisture out of the refrigerant circuit.

Chloride in some types of refrigerants such as R22 will cause the refrigerating machine oil to deteriorate.

Necessary Tools and Materials

Prepare the following tools and materials necessary for installing and servicing the unit.

Necessary tools for use with R410A(Adaptability of tools that are for use with R22 and R407C).

1. To be used exclusively with R410A ( Not to be used if used with R22 or R407C )

2. Tools and materials that may be used with R410 with some restrictions

3. Tools and materials that are used with R22 or R407C that can also be used with R410A

4. Tool and materials that must not used with R410A

Tools for R410A must be handled with special care, and keep moisture and dust from entering the cycle.

6

Read Before Installation

Maximum Operation Pressure Applicable Refrigerants

3.4MPa R22, R407C

4.15MPa R410A

Use pipes that meet the local standards.

Use pipes made of phosphorus deoxidized copper.

Since the operation pressure of the units that use R410A is higher than that of the units for use with R22, use pipes with

at least the radial thickness specified in the chart below. (Pipes with a radial thickness of 0.7mm or less may not be used.)

Although it was possible to use type-O for pipes with a size of up to

19.05(3/4") with conventional refrigerants, use type-

1/2H pipes for units that use R410A.(Type-O pipes may be used if the pipe size is

19.05 and the radial thickness is 1.2t.)

The table shows the standards in Japan. Using this table as a reference, choose pipes that meet the local standards.

The flare machining dimensions for units that use R410A is larger than those for units that use R22 in order to increase

air tightness.

If a clutch type flare tool is used to machine flares on units that use R410A, make the protruding part of the pipe between

1.0 and 1.5mm. Copper pipe gauge for adjusting the length of pipe protrusion is useful.

Size(mm) Radial Thickness(mm)Size(inch)

Type

Type-O pipes

Type-1/2H or Hpipes

Piping Materials

Types of Copper Pipes (Reference)

The table shows the standards in Japan. Using this table as a reference, choose pipes that meet the local standards.

Piping Materials/Radial Thickness

Flare Machining (type-O and OL only)

Flare Machining Dimension(mm)

External dimension of pipes

Size

Dimension A

R410A R22

6.35

9.52

12.7

15.88

19.05

1/4"

3/8"

1/2"

5/8"

3/4"

9.1

13.2

16.6

19.7

24.0

9.0

13.0

16.2

19.4

23.3

Flare Nut

Type-2 flare nuts instead of type-1 nuts are used to increase the strength. The size of some of the flare nuts have also

been changed.

Flare nut dimension(mm)

R410A(Type2) R22(Type1)

6.35

9.52

12.7

15.88

19.05

1/4"

3/8"

1/2"

5/8"

3/4"

17.0

22.0

26.0

29.0

36.0

17.0

22.0

24.0

27.0

36.0

6.35

9.52

12.7

15.88

1/4''

3/8''

1/2''

5/8''

0.8t

1.0t

19.05 3/4'' 1.0t

Dimension A

External dimension of pipes Size

Dimension B

7

8

NO

Wind direction

Air outlet

Cushion rubber

4.Installation dimension(Unit:mm)

*

9

1U07BS1ERA

1U09BS1ERA

1U12BS1ERA

1U18FS1ERA

1U24GS1ERA

1.

Outdoor unit

Indoor unit

A

B

Outdoor unit

Indoor unit

A

B

A

B

Outdoor unit

Indoor unit

Oil trap

Tobend a pipe,givetheroundnessaslargeaspossiblenottocrushthepipe,

ƽ

andthebendingradiusshouldbe30to40

mm or longer.

Connecting the pipe of gas side ﬁrst makes working easier.

ƽ

TheconnectionpipeisspecializedforR410A.ƽ

Half union

Flare nut

Torque wrench

CAUTION

Be careful that matters, such as wastes of sand

s,water,

,etc.shallnotenterthepipe.

ThestandardpipelengthisC m.IfitisoverDm,thefunctionoftheunitwillbeaffected.Ifthepipe

has

to be lengthened, the refrigerant should be charged,

according to E g/m. But the charge of refrigerant

must

beconductedbyprofes

sionalairconditionerengineer.Beforeaddingadditionalrefrigerant,

perform

air

purgingfromtherefrigerantpipesandindoorunitusing a vacuumpump,then

Spanner

Forced fastening without careful centering may

damagethethreadsandcause a leakageofgas.

Pipe Diameter(ǿ) Fastening torque

Liquid side6.35mm(1/4") 18N.m

Liquid/Gas side9.52mm(3/8") 42 N.m

Gasside12.7mm(1/2") 55N.m

Gasside15.88mm(5/8") 60N.m

Max.Elevation:

●

In case the elevation A is more

●

than 5m, oil trap shoud be

installed every 5~7

Max. Length:

●

In case the pipe length B is●

more thanDm, the refrigerant

should be charged, according

to E g/m.

Connection of pipes

charge

additional refrigerant.

Amax

Bmax

2.

10

11

(e.g.1U18FS1ERA)

12

1U07BS1ERA

1U09BS1ERA

1U12BS1ERA

1U18FS1ERA

1U24GS1ERA

T 25A/250V.

3

2

^

1

)

(

N

)(

L

)(

C

3

2

1

)

(

N

)

(

L

)

(

C

To Indoor unit

1U07BS1ERA

1U09BS1ERA

1U12BS1ERA

1U18FS1ERA 1U24GS1ERA

Model

Connecting wiring

Power cable

3G2.5mm

2

3G4.0mm

2

3G1.5mm

2

4G0.75mm

2

4G0.75mm

2

4G0.75mm

2

N

(

1

3

)

C(L

(

2

)

{

L

N

POWER

Outdoor unit

To Indoor unit

Outdoor unit

POWER

FOR 07K 09K 12K

FOR 18K 24K

13

15

Outdoor Unit

2

9

15

8

12

10

5

13

19

1

18

4

11

6

25

110

Haier Group

Address:No.1 Haier Road,Hi-tech Zone,Qingdao 266101 P.R.ChiQD

Contacts: TEL +86-532-8893-6943;FAX +86-532-8893-1010

Website: www.haier.com

Suction temperature sensor failure

When the The wiring of compressor is wrong or

the connection is poor

17

16

15

Lack of refrigerant

Check if there is leakage in the unit.

m

14

CONFORMIDAD DE LOS MODELOS

SEGÚN LAS NORMATIVAS EUROPEAS

CE

Todos los productos satisfacen los requisitos de las siguientes

normas europeas:

- Directiva de baja tensión, 73/23/CEE

- Directiva de baja tensión, 2006/95/CE

- Compatibilidad electromagnética 89/336/CEE

- Compatibilidad electromagnética 2004/108/CE

ROHS

Los productos satisfacen los requisitos de la directiva 2002/95/

CEE establecida por el Parlamento Europeo y el Consejo sobre

restricciones a la utilización de determinadas sustancias peligrosas

en aparatos eléctricos y electrónicos (Directiva RoHS UE).

WEEE

De acuerdo con la directiva 2002/96/CE del Parlamento Europeo,

se informa al consumidor acerca de los requisitos de eliminación

de productos eléctricos y electrónicos.

REQUISITOS DE ELIMINACIÓN:

Su aparato de aire acondicionado ha sido

marcado con este símbolo, el cual significa que

los productos de tipo eléctrico y electrónico

no deben mezclarse con residuos domésticos

sin clasificar. No intente desmontar el sistema

personalmente: tanto el desmontaje del sistema de aire

acondicionado como la manipulación del refrigerante, el

aceite y cualquier otro componente deben ser llevados

a cabo por un instalador capacitado, de acuerdo con la

legislación local y nacional al efecto. Los aparatos de aire

acondicionado deben ser manipulados en instalaciones de

manipulación especializadas y aptas para su reutilización,

reciclado y recuperación. Al garantizar la correcta

eliminación de este producto, usted contribuirá a evitar las

posibles consecuencias negativas que podría provocar

sobre el medioambiente y la salud humana. Póngase en

contacto con el instalador o la autoridad local pertinente

si desea obtener más información. Las pilas deben ser

extraídas del mando a distancia y eliminadas de forma

independiente, de acuerdo con la legislación local y nacional

al efecto.

INFORMACIÓN IMPORTANTE ACER-

CA DEL REFRIGERANTE UTILIZADO

1

1+2=

kg

R410A

2

kg

2=

1=

B

C

D

FE

kg

A

Este producto contiene gases fluorados de efecto invernadero

regulados por el Protocolo de Kioto. No los libere libremente a la

atmósfera.

Tipo de refrigerante: R410A

Valor GWP*: 1975

GWP = Potencial de contribución al calentamiento global

Escriba con tinta indeleble:

• 1 la carga de refrigerante que contiene el producto de fábrica

• 2 la cantidad de refrigerante adicional cargada durante la

instalación y

• 1+2 la carga total de refrigerante

en la etiqueta de carga de refrigerante suministrada con el

producto.

Una vez escritos los datos correspondientes, la etiqueta deberá

adherirse cerca de la conexión de carga del producto (por ejemplo,

sobre la parte interna de la cubierta de la válvula de retención).

A Contiene gases fluorados de efecto invernadero regulados por el

Protocolo de Kioto.

B Carga de refrigerante que contiene el producto de fábrica:

consulte la placa de características de la unidad.

C Cantidad de refrigerante adicional cargada durante la instalación.

D Carga total de refrigerante.

E Unidad exterior.

F Botella de refrigerante y colector de carga.

Contiene gases ﬂuorados de efecto invernadero

regulados por el Protocolo de Kioto.

Haier Industrial Park, No.1 Haier Road, Qingdao, República Popular China

F

A

C

E

D

A

F

C

E

D

G

B

G



4

Dibujos de instalación de las unidades interior y exterior

Los modelos cumplen la norma R410A sobre refrigerantes libres de HFC.

Para obtener información sobre la instalación de las unidades interiores, consulte el manual de instalación proporcionado

con las mismas.

(El diagrama muestra una unidad interior montada en pared.)

● La imagen anterior de las unidades interior y exterior solamente sirve de referencia.

Remítase al producto real adquirido.

más de 15 cm

Debe prestarse atención

a la pendiente del

manguito de drenaje

Organización de la

dirección de los tubos

Izquierda

Izquierda trasera

Derecha

trasera

Derecha

Inferior

más de

10 cm

más de 10 cm

más de

20 cm

más de 60 cm

Fijación de la unidad exterior

● Fije la unidad a un bloque de

cemento con pernos (10 mm) y

tuercas ﬁrme y horizontalmente.

● Si instala la unidad sobre una

pared, techo o tejado, instale un

soporte con clavos o cables consi-

derando la posibilidad de terremo-

tos o viento fuerte.

● Si la vibración afectase a la casa,

ﬁje la unidad instalando una alfom-

bra de absorción de vibraciones.

● Las marcas comprendidas

entre

A

y

G

en la

ilustración corresponden

a los números de las

piezas.

● La distancia entre la

unidad interior y el suelo

debe ser superior a 2 m.

Componentes opcionales para

la instalación de los tubos

Cinta no adhesiva

Cinta adhesiva

Soporte (L.S) con tornillos

Conexión de cable eléctrico para inte-

rior y exterior

Manguito de drenaje

Material aislante de calor

Cubierta

de oriﬁcio de entubación

más de 20 cm

más de 25 cm

Compresor (dentro de la unidad)

SALIDA DE AIRE

ENTRADA DE AIRE

TUBOS DE CONEXIÓN Y CABLEADO ELÉCTRICO

4 MANGUITO DE DRENAJE

15

Precauciones de seguridad

Lea detenidamente la siguiente información para poner en funcionamiento el aire acondicionado de forma correcta.

A continuación se enumeran tres tipos de precauciones de seguridad y sugerencias.

ADVERTENCIA Si realiza operaciones de forma incorrecta, pueden producirse graves consecuencias, como

la muerte o graves lesiones.

PRECAUCIÓN Si realiza operaciones de forma incorrecta, pueden producirse lesiones o daños en la

máquina; en algunos casos pueden producirse graves consecuencias.

INSTRUCCIÓN: Esta información puede asegurar el correcto funcionamiento de la máquina.

Símbolos utilizados en las ilustraciones

: indica una acción que se debe evitar.

: indica que es obligatorio seguir las instrucciones importantes.

: indica un componente que se debe conectar a tierra.

: atención a las descargas eléctricas (este símbolo se muestra en la etiqueta de la unidad principal.)

Después de leer este manual, entréguesela a aquellas personas que utilicen a la unidad.

El usuario de esta unidad debe tener este manual a mano y ponerlo a disposición de quienes repararán o reubicarán la unidad. Asimismo,

debe ponerlo a disposición de los nuevos usuarios cuando el producto cambio de manos.

Asegúrese de seguir estas importantes precauciones de seguridad.

ADVERTENCIA

● Si se producen fenómenos anormales

(por ejemplo, olor a quemado), corte la

fuente de alimentación inmediatamente,

y póngase en contacto con el distribuidor

para averiguar el método de manipulación.

En dicho caso, si sigue utilizando el aire acondicionado, éste

resultará dañado, y pueden producirse descargas eléctricas o

peligro de incendio.

● Tras un largo período de tiempo sin utilizar

el aparato de aire acondicionado, debe

comprobar la base para ver si se han pro-

ducido daños.

Si la base dañada no se repara, es posible

que la unidad se caiga y provoque acci-

dentes.

● No desmonte la boca de salida de la

unidad exterior.

La exposición del ventilador es muy peli-

grosa, ya que puede provocar lesiones

en las personas.

●

Cuando necesite mantenimiento y repa-

ración, llame al distribuidor para gestio-

narlo.

Si el mantenimiento y la reparación se

realizan de forma incorrecta podrían

producirse fugas de agua, descargas

eléctricas y peligro de incendio.

Desactivar

ADVERTENCIA

● No se pueden colocar cosas o personas

sobre la unidad exterior. La caída de cosas o

personas puede provocar accidentes.

●

No ponga en funcionamiento el aire acon-

dicionado con las manos mojadas. De lo con-

trario, se producirán descargas eléctricas.

●

Utilice sólo fusibles del tipo correcto.

No se puede utilizar ningún cable ni otro ma-

terial que sustituya al fusible, de lo contrario,

se producirán fallos o incendio.

●

Utilice el tubo de descarga correctamente

para asegurar la eﬁcacia de la descarga.

Si utiliza el tubo de forma incorrecta podrían

producirse fugas de agua.

●

Interruptor de circuito de fugas eléctricas instalado.

Provoca descargas eléctricas con facilidad sin el interruptor de

circuito.

●

El aire acondicionado no puede instalarse en lugares con gases

inﬂamables, ya que podrían provocar peligro de incendio.

El distribuidor es el responsable de la instalación del aparato de

aire acondicionado. Si la instalación se realiza de forma incor-

recta podrían producirse fugas de agua, descargas eléctricas y

peligro de incendio.

●

Llame al distribuidor para tomar medidas que eviten fugas de

refrigerante.

Si el aparato de aire acondicionado está instalado en una habita-

ción pequeña, asegúrese de tomar las medidas necesarias para

evitar

asﬁxia, incluso en caso de fuga de refrigerante.

● Cuando el aire acondicionado se instala o se vuelve a instalar, el

distribuidor en el responsable de dichas tareas.

Si la instalación se realiza de forma incorrecta podrían producir-

se fugas de agua, descargas eléctricas y peligro de incendio.

●

Conecte el cable de conexión a tierra.

El cable de conexión a tierra no debe conectarse al

tubo de gas, tubo de agua, barra pararrayos o línea

telefónica. Si la conexión a tierra se realiza de manera

incorrecta, podrían producirse descargas.

Puesta a

tierra

16

La pagina sta caricando ...

Haier 1U12BS1ERA Manuale del proprietario

Haier 1U12BS1ERA Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti