Ravelli Flexi 11 Use and Maintenance Manual

Marca: Ravelli

Modello: Flexi 11

Categoria: Stufe

Tipo: Use and Maintenance Manual

USE AND MAINTENANCE MANUAL

Flexi 11

INFORMATION ON SOLID FUEL HEATING APPLIANCES

According to Regulation (EU) No. 1185/2015

Fuel type Preferred fuel

(only one):

Other

suitable

fuel(s):

ηs

[x%]

Space heating emissions at

nominal heat output(*)

Space heating emissions at

minimum heat output (*) (**)

OGC

NOx

OGC

NOx

[x] mg/Nm3 at 13%O

Wood logs with moisture

content

≤ 25 % no no

Compressed wood with

moisture

content < 12 % yes no

92,6

164

165

109

Characteristics when operating with the preferred fuel only

Item

Symbol

Value

Unit

Type of heat output/room temperature control (select one)

Heat output

single stage heat output, no room temperature control

Nominal heat output

nom

10,2

two or more manual stages, no room temperature control

Minimum heat output (indicative)

nom

3,8

with mechanic thermostat room temperature control

Useful efficiency (NCV as received)

with electronic room temperature control

Useful efficiency at nominal heat output

th,nom

95,2

with electronic room temperature control plus day timer

Useful efficiency at minimum heat output (indicative)

th,min

94,6

with electronic room temperature control plus week timer

Yes

Auxiliary electricity consumption

Other control options (multiple selections possible)

At nominal heat output

max

0,071

room temperature control, with open window detection

At minimum heat output

min

0,010

room temperature control, with presence detection

In standby mode

0,002

with distance control option

Yes

(*) PM = particulate matter, OGCs = organic gaseous compounds, CO = carbon monoxide, NOx = nitrogen oxides

(**) Only required if correction factors F(2) or F(3) are applied.

Manufacturer

Aico

Model identifier(s)

Flexi 11 Decò

Brand

Ravelli

Indirect heating functionality

No kW

Direct heat output

10,2 kW

12 kW

Indirect heat output

-- kW

Decò - Glass - Steel

Preface

Dear Customer, We would like to thank you for choosing one of our stoves.

We invite you to read this manual carefully, before starting installation and use, so that you are able to benefit from all of its characteris-

tics better and in full safety. It contains all necessary information for correct installation, start-up, operation, cleaning, maintenance, etc.

Keep this manual in a suitable location, do not discard it without reading it.

Incorrect installation, maintenance and improper use of the product relieve the Manufacturer of all liability deriving from use of the stove.

For further information and requirements contact your Ravelli-authorised Technical Assistance Centre.

cluding photocopies, recordings or any other storage system, for other purposes that are not exclusively use by the buyer’s staff, without

the express written consent of the Manufacturer.

Use and maintenance manual Flexi 11

Pag.6

Rev.0 06/02/2023

INDEX

Preface........................................................................................................................................................................ 5

IDENTIFICATION .........................................................................................................................8

Stove identication ................................................................................................................................................... 8

Manufacturer identication ...................................................................................................................................... 8

Reference standards ................................................................................................................................................. 8

Remote control: Synthetic Declaration of Conformity (DoC) ................................................................................ 8

Label ........................................................................................................................................................................... 8

WARRANTY ..................................................................................................................................9

Certicate of warranty............................................................................................................................................... 9

Warranty conditions .................................................................................................................................................. 9

Registration of warranty ........................................................................................................................................... 9

Info and problems ..................................................................................................................................................... 9

GENERAL INFORMATION ......................................................................................................... 10

Supply and safe-keeping ....................................................................................................................................... 10

Language ................................................................................................................................................................. 10

Symbols used in the manual ................................................................................................................................. 10

SAFETY MEASURES .................................................................................................................10

General safety warnings ........................................................................................................................................ 10

Residual risks ......................................................................................................................................................... 11

DESCRIPTION OF THE APPLIANCE .........................................................................................12

Intended use ........................................................................................................................................................... 12

Reasonably foreseeable incorrect use ................................................................................................................. 12

Obligations and forbidden actions ....................................................................................................................... 13

Characteristics of the fuel ..................................................................................................................................... 14

TECHNICAL CHARACTERISTICS ............................................................................................15

Technical Data ......................................................................................................................................................... 15

Minimum clearances from combustible materials ............................................................................................... 16

Measurements ......................................................................................................................................................... 16

Technical diagram Flexi 11 Déco ........................................................................................................................... 16

Technical diagram Flexi 11 Glass .......................................................................................................................... 17

Technical diagram Flexi 11 Steel............................................................................................................................ 17

Main parts ................................................................................................................................................................ 18

Description of operation ......................................................................................................................................... 18

Automatic cleaning system .................................................................................................................................... 18

Recharge the fuel .................................................................................................................................................... 19

Doors opening ......................................................................................................................................................... 19

User training ............................................................................................................................................................ 19

Safety devices.......................................................................................................................................................... 20

The Majolica cladding (if applicable) ..................................................................................................................... 21

SHIPPING AND INSTALLATION ...............................................................................................22

Safety warnings for transportation and installation ........................................................................................... 22

Set-ups for the smoke evacuation system ........................................................................................................... 23

Installation ............................................................................................................................................................... 24

Use and maintenance manual Flexi 11

Pag.7

Rev.0 06/02/2023 EN

CONNECTIONS .......................................................................................................................... 27

Connection with external air intake ....................................................................................................................... 27

Chimney connection .............................................................................................................................................. 27

Standard installation ............................................................................................................................................... 27

Concentric installation ............................................................................................................................................ 28

Rear smoke outlet ................................................................................................................................................... 29

Electrical connection .............................................................................................................................................. 30

Ducting ..................................................................................................................................................................... 31

Connection of external probe or thermostat ....................................................................................................... 31

Testing and commissioning .................................................................................................................................. 31

Electric scheme Flexi 11 ......................................................................................................................................... 32

CONTROLS AND USE .................................................................................................................33

Control panel description ....................................................................................................................................... 33

Radio touch remote control initialization ............................................................................................................. 33

Description of the radio touch remote control ..................................................................................................... 34

Description of the display ...................................................................................................................................... 34

Time and date setting ............................................................................................................................................. 35

PROCEDURES FOR USE ...........................................................................................................36

Checks prior to start-up ......................................................................................................................................... 36

Auger loading .......................................................................................................................................................... 36

Switching the appliance on and o ....................................................................................................................... 36

Failed ignition ......................................................................................................................................................... 37

Setting operating temperature and power: .......................................................................................................... 37

OPERATING PHASES OF THE APPLIANCE ..............................................................................37

Sequence of ignition phases .......................................................................................................................... 37

Modulation ............................................................................................................................................................... 37

Description of menu functions .............................................................................................................................. 37

Setting ...................................................................................................................................................................... 40

Ventilation menu ...................................................................................................................................................... 42

Single ducting ......................................................................................................................................................... 42

Stove phase general layout .................................................................................................................................... 45

Warning Pop -Up ..................................................................................................................................................... 46

Alarms (table with reference codes) ...................................................................................................................... 46

INSTALLATION QUICK GUIDE RAVELLI SMART WI-FI ...........................................................49

Connect the WiFi module cable ............................................................................................................................. 49

App ............................................................................................................................................................................ 49

Connection to the WiFi module .............................................................................................................................. 49

Account registration ............................................................................................................................................... 51

MAINTENANCE ..........................................................................................................................53

Safety warnings for maintenance .......................................................................................................................... 53

Cleaning .................................................................................................................................................................. 53

Extraordinary maintenance .................................................................................................................................... 54

TROUBLESHOOTING .................................................................................................................57

The appliance does not work ................................................................................................................................. 57

Dicult lighting ....................................................................................................................................................... 57

Smoke leakage......................................................................................................................................................... 57

The glass gets dirty easily ...................................................................................................................................... 57

Downtime (end of season) ..................................................................................................................................... 57

DISPOSAL AT END OF SERVICE LIFE ......................................................................................57

Warnings for the correct disposal of the product ................................................................................................ 57

Use and maintenance manual Flexi 11

Pag.8

Rev.0 06/02/2023

IDENTIFICATION

Stove identication

Type of product PELLET STOVE

Trademark Ravelli

Model Flexi 11 Déco - Flexi 11 Glass - Flexi 11 Steel

Manufacturer identication

Manufacturer Aico S.p.A.

Via Consorzio Agrario, 3/D - 25032

Chiari (BS) - Italy

T. + 39 030 7402939

[email protected]

www.ravelligroup.it

Reference standards

The Flexi 11 stoves that this manual refers to are compliant with the regulation:

305/2011, CONSTRUCTION PRODUCT REGULATION

and the following directives

2014/53/EU (RED)

2011/65/EU 2015/863/EU, 2017/2102/EU, (RoHS)

2009/125/EC (Ecodesign)

And the following harmonised standards and/or technical specications have been applied:

EN 14785; EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3; EN 60335-1; EN 60335-2-102; EN 62233; EN 50581; ETSI

EN 300220-1

All local regulations, including those referring to national and European standards, must be respected when installing the appliance.

Remote control: Synthetic Declaration of Conformity (DoC)

The manufacturer Aico S.p.A. declares that the Remote Control, with the Ravelli brand and model PNET00003 (Palm Touch) is in

conformity with the relevant Union harmonisation legislation: 2014/53/EU (RED), and that the following harmonised standards and/

or technical specications have been applied: ETSI EN 301 489-3, ETSI EN 301 489-1, EN 60950-1 A11+A1+A12+AC+A2, EN

62479.

These declarations can be found in full format on the website www.ravelligroup.it.

Label

The following symbols are used on the label:

PIN,nom Heat input power (max) PIN,part Heat input power (min)

Pnom Nominal power Ppart Reduced power

PWnom Nominal water heat output PWpart Reduced water heat

output

PSnom Nominal air heat output PSpart Reduced air heat output

COnom CO at nominal power COpart CO at reduced power

ηnom Efficiency at nominal

power

ηpart Efficiency at reduced

power

pnom Minimum draught at

nominal power

Tnom Flue gas temperature at

nominal power

WElectrical consumption

TW,max Maximum water

temperature

TW,max-set Maximum adjustable

water temperature

pWnom Max working pressure 230 V -

50 Hz

Alimentation

Distance to combustible materials

dS-L Left side dCCeiling

dS-R Right side dFFront

dRRear dBFloor

n.d.: undeclared data

Usare solo il combustibile raccomandato:

Use only reccomended fuel:

Utilizer seulement les combustibles recomandés:

Use solo el combustible recomandado:

Gebruik alleen de aanbevolen brandstof:

Nur empfohlenes Brennmaterial verwenden:

50 Hz

Pellet di legno

10,7 kW 4,0 kW

10,2 kW 3,8 kW

0,013 %0,013 %

94,6 %95,2 %

100 °C

10 Pa 0,1 mbar

330 W

230 V

APPARECCHIO PER IL RISCALDAMENTO DOMESTICO ALIMENTATO A PELLET DI LEGNO

RESIDENTIAL SPACE HEATING APPLIANCE FIRED BY WOOD PELLETS

APPAREIL DE CHAUFFAGE DOMESTIQUE À CONVECTION À GRANULES DE BOIS

APARATO DE CALEFACCION DOMESTICA ALIMENTADO CON PELLETS DE MADERA

HUISHOUDELIJKE RUIMTEVERWARMINGSTOESTELLEN GESTOOKT MET GEPERST HOUT

RAUMHEIZER ZUR VERFEUERUNG VON HOLZPELLETS

Model: Flexi 11 Déco

IN,nom

IN,part

nom

part

nom(13%O2)

part(13%O2)

nom

part

nom

Wood pellet

Granulee de bois

Pellet de madera

Houtpellet

Holzpellets

Ø 6 mm

Leggere le istruzioni d’uso

/ Read and follow the operating manual / Lire et suivre le mode d’emploi / Lea

y respete le manual de operacion / Lees en volg de handleiding voor bediening / Bitte lesen und befolgen

Sie die Montage und Nutzungsanweisungen

Distanza minima da materiali infiammabili

Minimum distance from flammable materials

Distance moindre de matériels inflammables

Distancia minima de materiales inflamables

Minimale afstand van brandbare materialen

Mindestabstand zu brennbaren Materialien

200 mm

S-L

S-R

800 mm

1000 mm

0 mm

D.o.P. n° 311CPR13.07 (Notified Body 0476)

EN 14785:2006

TYP FC62X

Anno di produzione: 2023

AICO S.p.A. - Via Consorzio Agrario, 3/D - 25032 Chiari (BS) - Italy

3YR-P-068

C399Q1001

Use and maintenance manual Flexi 11

Pag.9

Rev.0 06/02/2023 EN

WARRANTY

Certicate of warranty

Ravelli thanks you for the trust granted with the purchase of one of its products and invites the purchaser to:

• read the installation, use and maintenance instructions for the product;

• read the warranty conditions contained below.

Warranty conditions

The warranty for the Customer is acknowledged by the Dealer under the terms of law.

The Dealer acknowledges the warranty only if the product has not been tampered with and only if it has been installed in accordance with

the Manufacturer’s instructions.

The limited warranty covers manufacturing material defects, as long as the product has not broken sue to an incorrect use, negligence,

incorrect connection, tampering, installation errors.

The warranty becomes null and void even if only one requirement in this manual is not complied with.

The following are not covered by warranty:

• the combustion chamber refractory stones;

• the door glass;

• the gaskets;

• the paint job;

• the stainless steel or cast iron combustion grille;

• the resistance;

• the Majolica cladding;

• the aesthetic parts;

• any damages caused by unsuitable installation and/or use of the product and/or shortcomings on the part of the customer.

The use of poor quality pellet or any other unauthorised fuel may damage the product’s components, cause its warranty to be voided and

as a result eliminate the connected manufacturer liability.

It is therefore recommended to use good quality pellet that fulfils the requirements listed in the dedicated chapter.

All damages caused by transportation are not recognised, for this reason it is recommended to carefully check goods upon receipt,

immediately warning the reseller of any damage.

Registration of warranty

To activate the warranty, it is necessary to register the product on the Guarantee Portal on the website

www.ravelligroup.it, by entering your data and the purchase receipt.

Info and problems

Dealers authorised by Ravelli use a trained Technical Service Centre network to meet the Customer’s requirements. For any information

or request for assistance, please contact your Dealer or the Technical Service Centre.

Use and maintenance manual Flexi 11

Pag.10

Rev.0 06/02/2023

GENERAL INFORMATION

Supply and safe-keeping

The manual is supplied in printed format.

Keep this manual safe, with the appliance, so that the user can consult it easily.

The manual is an integral part, for safety reasons, therefore:

• it must be kept intact (in full). If it gets lost or ruined it is necessary to immediately ask for a new copy:

• it must be kept with the appliance until demolition (including relocation, sale, rental, lease, etc....).

The Manufacturer will not be held liable for improper use of the appliance and/or damage caused by operations that are not set forth

in the technical documentation.

Language

The original manual was written in Italian.

Any translations into additional languages must be carried out based on the original instructions.

The Manufacturer is liable for the information contained in the original instructions; the translations into dierent languages cannot be

fully veried therefore if any inconsistency arises it will be necessary to follow the text in the original language or contact our Technical

Documentation Oce.

Symbols used in the manual

symbol denition

📌This symbol is used to identify particularly important information in the manual. This information also concerns the

safety of users involved in using the appliance.

This symbol is used to identify important warnings for the safety of the user and/or the appliance.

SAFETY MEASURES

General safety warnings

📌Read this instructions manual carefully before appliance

installation and use. Failure to observe the instructions set

forth herein can void the warranty and/or cause damage to

property and/or people.

Appliance installation, system verification, operation verification

and initial calibration must be carried out exclusively by qualified

and authorised staff.

The appliance needs to be connected to a single chimney

that guarantees the draught declared by the Manufacturer

and observes the installation regulations that apply to the

installation site.

The room where the appliance is installed must have an air

intake.

The appliance must not be used as an incinerator or differently

from its purpose

Use and maintenance manual Flexi 11

Pag.11

Rev.0 06/02/2023 EN

Do not use any fuel other than fire pellet. It is strictly forbidden

to use liquid fuels.

It is prohibited to use the appliance with the door or ash drawer

open or the glass broken.

Do not touch the hot surfaces of the appliance without suitable

protective equipment, to avoid getting burned. When it is

running, the outer surfaces reach hot temperatures to the

touch.

It is forbidden to make unauthorised changes to the appliance.

Before using the appliance it is necessary to know the position

and function of the controls.

If the chimney catches fire you must call the fire brigade.

Only use original spare parts. Any tampering and/or

replacements that have not been authorised by Ravelli can

pose a danger to the user’s safety.

In the event of particularly adverse weather conditions, the

safety systems could intervene and switch off the appliance.

In any case, doe not disable the safety systems.

Residual risks

The appliance was designed so as to guarantee the user’s essen-

tial safety requirements.

Safety was integrated into the appliance’s design and construction

as much as possible.

For every residual risk there is a description of the risk and the

zone or part that is applies to (unless the risk applies to the entire

appliance overall). Procedure-related information is also provided

on how to avoid the risk and on the correct use of the personal pro-

tective equipment required by and made compulsory by the Man-

ufacturer.

Use and maintenance manual Flexi 11

Pag.12

Rev.0 06/02/2023

Residual

risk

Description procedure-related information

Risk of

burns

When the appliance is running, it may reach high

temperatures to the touch, especially on its external

surfaces. Take care to avoid burns and use the specic

tools if necessary.

Use the supplied glove to open pellet cover for loading

operations.

DESCRIPTION OF THE APPLIANCE

Intended use

The appliance in question is intended for:

Operation Allowed fuel Forbidden Setting

Domestic space

heating by

burning:

Pellet Any fuel other

than the

permitted ones.

Residential

Commercial

The appliance is designed and built to work safely if:

• it is installed by qualied sta according to the specic standards;

• it is used within the limits declared in the contract and herein;

• the operating manual procedures are followed;

• routine maintenance is carried out according to the times and

methods set forth;

• extraordinary maintenance is promptly carried out when needed;

• safety devices are not removed and/or bypassed.

📌This appliance must be intended for the use it was specifically

designed for.

Reasonably foreseeable incorrect use

Reasonably foreseeable incorrect use is listed below:

• using the appliance as an incinerator;

• using the appliance with fuel other than pellet;

• using the appliance with liquid fuels;

• using the appliance with the door open and the ash drawer out.

Any use of the appliance other than intended must be preventively

authorised in writing by the Manufacturer. Without said written

authorisation, the use is considered “improper”. Any contractual

and non-contractual liability of the manufacturer is excluded for

damages to persons, animals or property due to installation and

maintenance adjustment errors and improper use.

Use and maintenance manual Flexi 11

Pag.13

Rev.0 06/02/2023 EN

Obligations and forbidden actions

Obligations

The user must:

• read this instructions manual before performing any operation

on the appliance;

• the appliance must not be used by children under the age of 8 or

by people with reduced physical, sensorial or mental capacities

or without experience or without the necessary knowledge, and

always with supervision;

• do not use the appliance improperly, i.e. for uses other than those

described in the “INTENDED USE” paragraph;

• it is strictly forbidden to use liquid fuels;

• keep objects that are not heat and/or ame-resistant at a safe

distance;

• only and exclusively load the appliance with pellet with the

characteristics described herein;

• connect the appliance to a regulation chimney;

• provide a suitable system for the supply of combustion air (air

intake or intake duct for watertight appliances);

• always perform maintenance with the appliance o and cold;

• perform cleaning activities at the frequency stated herein;

• use original parts recommended by the Manufacturer.

Forbidden actions

The user must never:

• remove or change the safety devices without authorisation;

• perform operations or manoeuvres of his/her own initiative that

are not part of his/her job description, meaning that he/she might

jeopardise his/her own safety and that of others;

• use fuels other than pellet and those allowed for lighting;

• use the appliance as an incinerator;

• use ammable or explosive substances near the appliance

during operation;

• use the appliance with the door open and/or with the glass ruined

or broken;

• close the combustion air and smoke outlet openings, whatsoever;

• use the appliance to dry laundry;

• replace or change some of the appliance parts.

Use and maintenance manual Flexi 11

Pag.14

Rev.0 06/02/2023

Characteristics of the fuel

Wood pellet is a fuel made of pressed wood sawdust, often recovered from processing scraps of carpentries. The material used

cannot contain any extraneous substance such as, for example, glue, lacquer or synthetic substances.

The sawdust, once it has been dried and cleaned from impurities, is pressed using a die with holes: as a result of high pressure, the

sawdust heats up by activating the natural wood binders; this way the pellet maintains its shape even without adding articial

substances.

Wood pellet density varies based on the type of wood and can exceed that of natural wood by 1.5 - 2 times.

The cylinders have a diameter of 6 mm and a variable length between 10 and 40 mm.

Their density is equal to approximately 650 kg/m3. Due to their low water content (< 10%) they have a high energy content.

The UNI EN ISO 17225-2:2014 standard (that replaces the EN PLUS standard) denes pellet quality by specifying three classes: A1,

A2 and B. Maintain fuels and other ammables at a suitable distance.

Ravelli recommends using wood pellet classied A1 and A2 according to the EN ISO 17225-2:2014 standard, or certied DIN PLUS

(more restrictive than the A1 class) or ONORM M 7135. Pellet may be light or dark coloured, it is normally bagged into bags that show

the name of the producer, the main characteristics and classication according to standards.

📌Only use certified pellets. Poor-quality pellets can increase the rate at which dirt builds up on the glass and increase

maintenance work.

📌Using fuel that is not compliant with the above will void the warranty.

Use and maintenance manual Flexi 11

Pag.15

Rev.0 06/02/2023 EN

TECHNICAL CHARACTERISTICS

Technical Data

Units of measurement Flexi 11

Energy efficiency class - - A++

Heating input reduced - nominal kW 4,0 - 10,7

Heating output reduced - nominal kW 3,8 - 10,2

Red. - Nom. Yield % 94,6 - 95,2

Hourly consumption Kg/h 0,84 - 2,21

Loading interval h 9 - 23

Max. heating volume* m3185 - 290

CO at 13% of O2% 0,013 - 0,013

mg/m3 165 - 164

OGC at 13% of O2mg/m3 3 - 4

NOX at 13% of O2mg/m3 109 - 97

PM at 13% of O2mg/m3 18,0 - 14,0

Smoke temperature °C 89 - 164

Smoke ow g/s 3,0 - 5,4

Minimum draft Pa - mbar 6 - 11

0,06 - 0,11

Electrical connection Hz - V 50- 230

Electrical power consumption max. W 330

Electrical power consumption reduced - nominal W 10- 71

Stand-by electrical consumption W 2,3

smoke air inlet Ø mm 50

smoke outlet pipe Ø mm 80

Hopper capacity Kg 19

Seasonal energy eciency % 92,6

Type of room temperature control with electronic room temperature control plus week timer

Other control options with distance control option

The data shown here is provided as a guideline and is not binding, and may change based on what type and quality of wood is used.

Ravelli reserves the right to make any changes in order to improve product performance.

* Heatable volume based on the requested power equal to 35 W/m³ and 55 W/m³.

Use and maintenance manual Flexi 11

Pag.16

Rev.0 06/02/2023

Minimum clearances from combustible materials

Unit of

measurement Flexi 11

R Right side mm 200

L Left side mm 200

B Rear mm 200

A Front mm > 1000

Measurements

Unit of

measurement Flexi 11 Déco Flexi 11 Glass Flexi 11 Steel

Height mm 1190 1190 1190

Width mm 530 530 530

Depth mm 665 665 665

Weight kg 210 200 200

Technical diagram Flexi 11 Déco

530

0911

665

530

665

80/130 NORMAL OR CONCENTRIC SMOKE OUTLET

80 CANALISATION

80 OPTIONAL SMOKE

OUTLET

50 AIR INLET IF NO CONCENTRIC

FLUE PIPE IS USED

Use and maintenance manual Flexi 11

Pag.17

Rev.0 06/02/2023 EN

Technical diagram Flexi 11 Glass

Technical diagram Flexi 11 Steel

530

0911

665

530

665

80 CANALISATION

80/130 NORMAL OR CONCENTRIC SMOKE OUTLET

80 OPTIONAL SMOKE

OUTLET

50 AIR INLET IF NO CONCENTRIC

FLUE PIPE IS USED

530

0911

665

530

665

80/130 NORMAL OR CONCENTRIC SMOKE OUTLET

80 CANALISATION

80 OPTIONAL SMOKE

OUTLET

50 AIR INLET IF NO CONCENTRIC

FLUE PIPE IS USED

Use and maintenance manual Flexi 11

Pag.18

Rev.0 06/02/2023

Main parts

A Grid for air passage

B Combustion chamber door

C Ashes drawer

D Pellet cover

E Control panel

F Combustion chamber

G Grid for ashes

H Brazier

I Reset thermostat

L Air passage gap

Description of operation

Ravelli pellet stoves of the Flexi 11 family are home heating appliances powered by wood pellets with automatic loading. They are

suitable for use as a secondary heating system or as a support for the main heating system.

The heat generated by pellet combustion is diused in the installation room by radiation and natural convection. It is possible to

choose whether to activate the front fan or keep the stove in operation by natural convection. In addition, in the Flexi 11 versions it

is possible to activate the ducting to heat another room, subject to activation by the installer.

The stove is controlled by an electronic control unit that manages the start-up, operation and shutdown phases and also includes

many other functions for control, programming and safety.

The user can choose the operating power from 5 levels, or set the temperature to be maintained in the room. In this case the stove

will manage the power to ensure maximum comfort. Among the functions of the electronic control unit there is also that of being

able to program the start-up and shutdown of the stove, setting the weekly chronothermostat.

All this can be done comfortably from the sofa using the handheld remote control.

Ravelli’s patented cleaning system minimises maintenance by the user. There is no longer any need to clean the brazier before

each lighting and all maintenance operations.

This stove has been designed for hermetic installations, so it can be installed in the traditional way, or by taking air directly from

outside.

Automatic cleaning system

The stove is equipped with atuomatic brazier cleaning system. This means that there is no need to carry out daily manual cleaning of the

brazier or every time the stove is lit. The automatic cleaning system is activated every time the stove is lit and after 6 hours of continuous

operation. The cleaning cycle, which involves shutting down, automatic cleaning and restarting the stove, takes about 10 minutes. During

this period the heating is guaranteed by the heat accumulated by the appliance itself.

Note: the times indicated are those set by default by the Manufacturer.

A A

B B

C C

D D

E E

F F

G G

H H

J J

K K

L L

M M

N N

P P

R R

T T

DISEG.

VERIF.

APPR.

FABB.

Qual.

SE NON SPECIFICATO:

QUOTE IN MILLIMETRI

FINITURA SUPERFICIE:

TOLLERANZE:

LINEARE:

ANGOLARE:

FINITURA:

INTERRUZIONE

BORDI NETTI

NOME

FIRMA

DATA

MATERIALE:

NON SCALARE DISEGNO

REVISIONE

TITOLO:

N. DISEGNO

SCALA:1:5

FOGLIO 1 DI 1

PESO:

90017GR01

A A

B B

C C

D D

E E

F F

G G

H H

J J

K K

L L

M M

N N

P P

R R

T T

DISEG.

VERIF.

APPR.

FABB.

Qual.

SE NON SPECIFICATO:

QUOTE IN MILLIMETRI

FINITURA SUPERFICIE:

TOLLERANZE:

LINEARE:

ANGOLARE:

FINITURA:

INTERRUZIONE

BORDI NETTI

NOME

FIRMA

DATA

MATERIALE:

NON SCALARE DISEGNO

REVISIONE

TITOLO:

N. DISEGNO

SCALA:1:5

FOGLIO 1 DI 1

PESO:

90017GR01

Use and maintenance manual Flexi 11

Pag.19

Rev.0 06/02/2023 EN

Recharge the fuel

Use only wood pellets, the characteristics shown in this manual.

During pellet loading prevent the pellet bag from coming into contact with hot surfaces.

📌It is not recommended to empty the pellet bag directly into the hopper to avoid depositing wood sawdust on the bottom of

the hopper.

To load the pellets inside the hopper, proceed as described below:

Step Action

1 Open the pellet hopper cover

2 Lift the slide

3 Pour the pellets into the hopper

4 Close the pellet hopper cover

Doors opening

The combustion chamber door, the pellet hopper lid and the ash drawer can only be opened when the stove is in the OFF state.

If one of them is not closed, the pellet supply is interrupted, the control unit emits an acoustic warning signal, while the symbol appears on

the display:

In this condition, by touching the CONFIRM button you can read the detail of the warning: “doors and ash pan open”. If the combustion

chamber door, the pellet hopper lid and / or the ash drawer are not closed within 1 minute, the stove switches off signaling ALARM 07.

Opening the doors also interrupts the automatic cleaning phase of the brazier. In the event of a prolonged interruption of the cleaning

phase, ALARM 19 may appear.

Remember that in the presence of an alarm the stove will have to be restarted manually.

User training

Once installation is complete, the user must always be fully trained in the functions and characteristics of the stove by the technician au-

thorized by Ravelli to ensure optimal and safe use.

The training should cover the following topics:

• Description of the stove, its operation and basic settings

• How to turn the stove on and off safely

• Fuel storage and refilling

• What to do in the event of an alarm, in particular that of “no ignition”

• How to clean the stove correctly and the importance of performing it on a regular basis

• It is advisable to schedule the first annual maintenance

Use and maintenance manual Flexi 11

Pag.20

Rev.0 06/02/2023

Safety devices

The stove has been designed and equipped with safety systems to minimize user risks.

It is equipped with the safety devices listed in the following table, which also intervene in case of failure of the electronic board.

Element Description

Pellet tank thermostat If the temperature exceeds the set safety value, it immediately stops the pellet loading

motor and the stove is automatically switched o; to restart it, it is necessary to wait until

it has cooled down and manually reset the thermostat, using the appropriate button.

Pressure switch If the pressure in the smoke outlet duct is too high (a sign that the smoke evacuation sys-

tem is obstructed) it immediately stops the pellet loading motor and the stove switches off

automatically.

Combustion chamber door closing

limit switch, the ash drawer and pellet

hopper lid

If the door of the combustion chamber, the ash drawer and pellet hopper lid are not prop-

erly closed, they immediately stop the pellet loading motor; if they are not closed within

60 seconds, the stove switches off automatically.

Electrical safety In case of failure of the electrical components or wiring, the fuse and grounding keep the

appliance safe. It is necessary that the electrical system of the house is up to standard,

equipped with a grounding circuit and all the safety systems required by the standards.

It should be noted that the stove’s operating program has been designed to stop stove operation in the event of malfunctions:

Anomalies Description

Temperature in the combustion

chamber

If the temperature probe in the combustion chamber detects temperatures that are too

high or too low, the stove is switched off and the relative alarm is displayed.

Flue gas temperature If the temperature probe at the smoke outlet detects temperatures that are too high, the

stove is switched o and the relative alarm is displayed.

Smoke fan break If the fan stops, the electronic board blocks the supply of pellets and the alarm is dis-

played.

Gear motor failure If the gear motor stops, the appliance switches off safely.

Temporary power failure If a power failure occurs during operation, when the power returns the temperature in the

combustion chamber is checked and, if necessary, the stove goes into cooling mode.

No ignition If no ame develops during the ignition phase, the stove goes into alarm.

It is forbidden to tamper with the safety devices. Restarting the product is only possible after eliminating the cause that

caused the intervention of the safety system. To understand which anomaly occurs, consult this manual which explains,

depending on the alarm message that the device displays, how to intervene on it.

If the problem persists, contact the Support Service.

La pagina sta caricando ...

Ravelli Flexi 11 Use and Maintenance Manual

Marca: Ravelli

Modello: Flexi 11

Categoria: Stufe

Tipo: Use and Maintenance Manual

Scarica il pdf

rapporto

in altre lingue

English: Ravelli Flexi 11

Documenti correlati

Altri documenti

Skylight AQCT-3 Manuale utente