Bushnell Core DS Istruzioni per l'uso

3

English / Anglais / Inglés / Inglese / Engels

Quick Start Guide (119936C/119938C/119975C/119977C)

For full instruction manual go to: www.bushnell.com

To get Started using your Bushnell Trail Camera:

1. Install 6 AA batteries (lithium* or alkaline) and SD card (up to 32GB max.)

*lithium batteries are recommended

2. At the location you will place the camera, power it on.

3. Mount the camera using the tree strap.

4. Your camera is now ready to use at its default settings: photo mode, 10 sec interval between

photos, 8MP resolutions, “Hi” LED Power.

5. The default settings can be changed to your preferences (for example, if you would rather

capture videos, or photos at a different resolution, spaced further apart) using the display on

the camera?

(see full manual at www.bushnell.com for more details)

Customer Service: 800-423-3537

www.bushnell.com

4

IMPORTANT NOTE

Congratulations on your purchase of one of the best trail cameras on the market! Bushnell is very proud

of this camera and we are sure you will be pleased with it as well. We appreciate your business and

want to earn your trust. Please refer to the notes below and the instructions in this manual to ensure

that you are completely satisfied with this product.

If your Bushnell Core Trail Camera does not seem to be functioning properly or if you are having

photo/video quality issues, please check the Troubleshooting/FAQ section on pages 21-24.

Problems are often due to something simple that was overlooked, or require only changing one setting

to solve.

If your problem continues after trying the solutions in the Troubleshooting/FAQ section, please call

Bushnell Customer Service at (800) 423-3537. In Canada, call (800) 361-5702.

Do not mix old and new batteries

Do not mix battery types-use ALL lithium or ALL alkaline.

Bushnell recommends using SanDisk® class 6 or faster SDHC Cards (up to 32GB capacity) in your Core

Trail Camera.

INTRODUCTION

About the Core Trail Camera

The Bushnell Core Trail Camera is a digital scouting camera. It can be triggered by any movement of

game in a location, detected by a highly sensitive Passive Infra-Red (PIR) motion sensor, and then take

high quality pictures (up to24MP or 30MP still photos), or video clips.

The Core Trail Camera consumes very little power (less than 0.08 mA) in a stand-by (surveillance) state.

This means it can deliver up to six months stand-by operation time when the device is powered by the

full capacity of AA alkaline batteries, and up to twelve months utilizing lithium AA batteries. Once

motion in the monitored area is detected, the digital camera unit will be triggered at once (typically

within half a second) and then automatically take photos or videos according to previously programmed

settings. The Core Trail Camera is equipped with built-in infrared LEDs that function as a flash, so that it

delivers clear photos or videos (in black & white) even in the dark, and it can take color photos or videos

under sufficient daylight. The Core Trail Camera is designed for outdoor use and is resistant against

water and snow.

Your trail camera is one of the latest generation of Bushnell Core Trail Camera.

5

Core Trail Cameras, and includes many new or improved features, including:

• Dual Sensor (119975C/119977C only) – the camera has dual sensors in order to capture the best

quality images for both day and night.

• Auto PIR Sensitivity - the camera monitors ambient temperature conditions and automatically adjusts

the sensor/trigger signal to be more sensitive to slight variations in temperature on hot days, less

sensitive on cold days.

• Removable Battery Tray – replaceable battery tray in order to easily exchange your batteries quickly.

Built in latch in order to catch the tray from falling out of the camera.

• GPS Geotag Capability - allows the user to input the longitude and latitude of the camera’s position,

which will be embedded in each photo file. This enables Google Earth, Picassa and other geotag enabled

software to automatically show a map pinpointing each camera’s location when a group of photos are

reviewed on a computer. Especially useful for those who setup multiple Core Trail Camera s to monitor

large or widely separated areas.

• Multi Flash Mode (LED Control) - prevents overexposed flash photos at close range.

• Hybrid Capture Mode - allows both still photos and videos to be captured at each trigger, up to

highest resolution settings for each.

• NV Shutter - user can select shutter speed for images captured at night allowing control over

brightness vs. ability to stop motion.

• Camera Operating Mode can be limited to Day only, Night only, or 24 HRs

• Preset Modes for Feeder, Trail and Food Plot applications.

• Dynamic Video mode uses the duration of animal activity to determine the length of the captured file,

so your video doesn't stop right as things get interesting.

And many more features such as video with audio, 0.2 second trigger speed and 0.6 second recover time

(still photos), widescreen or fullscreen format still photos, imprintable camera name (user set) along

with current data including temperature and moon phase.

Applications

The Core Trail Camera can be used as a trail camera for hunting or scouting game. It is also suitable for

surveillance usage.

PARTS AND CONTROLS

The Core Trail Camera provides the following connections for external devices: USB port, SD card slot

and external DC power in (pg 6, Fig. 1).

A 3-way power switch is used to select the main operating modes: OFF, SETUP, and ON (pg 6, Fig. 2).

A D-Pad interface with five keys is primarily used in SETUP mode to select operational functions and

parameters. As shown on the next page, these keys are: UP, DOWN, LEFT, RIGHT, OK and ENTER. Three

of the keys can also perform a second function (shortcut operations in SETUP mode) in addition to their

main function: The DOWN key can be used to set the camera to Photo mode (still camera icon), and the

UP key can set the camera to Video mode (movie camera icon). The RIGHT key also serves as the manual

shutter (“SHOT”) button of the camera. These secondary functions are indicated by icons or text above

the key as shown on the next page.

6

7

INSTALLING THE BATTERIES AND SD CARD

Before you begin learning how to use your Core Trail Camera, you will first need to install a set of

batteries and insert an SD card. Although that may only take you a minute, there are some important

notes about both batteries and SD cards you should be aware of, so please take the time to read the

following directions and cautions:

Loading Batteries

After opening the latch on the right side of the Core Trail Camera, you will see that the Core Trail

Camera has a battery release button. Depress this button and a battery tray will drop out of the

bottom of the camera. The battery tray will stop about ½ inch out of the device, this is a latch system to

prevent the tray from dropping onto the ground. Just apply a little pressure when pulling and the tray

will release. The battery tray has six battery slots. Install a full set of 6 batteries. Be sure to insert each

battery with correct polarity (negative or “flat” end against the long spring of each battery slot).

Bushnell recommends using a full set of new lithium AA (Energizer® brand) or alkaline AA batteries.

NiMh Rechargeable batteries are not recommended, as the lower voltage they produce can cause

operational issues.

You can also connect an optional Solar Panel accessory (model# 119756C –please visit

www.bushnell.com for more information) to the “DC In” jack at the bottom of the Core Trail Camera

(other external power supplies should not be used, as the camera and/or display may not function

correctly). If the solar panel is connected and AA batteries are installed, the Core Trail Camera will be

powered by the solar panel's rechargeable lith-ion battery, as long as it provides adequate voltage (if

not, the camera will switch to battery power). The solar panel's battery will power the camera at night.

Inserting the SD Card

Insert the SD card (with the camera’s power switch in the OFF position) before beginning to operate the

camera. Don’t insert or remove the SD card when the power switch is in the ON position.

The Core Trail Camera uses a standard SD (Secure Digital) memory card to save photos (in .jpg format)

and/or videos (in .mp4 format). SD and SDHC (High Capacity) cards up to a maximum 32GB capacity are

supported. Using high speed SD cards (SanDisk® SDHC rated class 6 or higher) is recommended if you

will use the 1280x720 or 1920x1080 video settings. Before inserting the SD card into the card slot after

8

opening the camera’s front cover, please make sure that the write-protect switch on the side of the card

is “off” (NOT in the “Lock” position). The following describes how to insert and remove the SD card:

• Insert the SD card into the card slot with its label side upwards (see below). A “click” sound

indicates that the card is installed successfully. If the wrong side of the card is facing up, you will

not be able to insert it without force-there is only one correct way to insert cards. If the SD card

is not installed correctly, the device will not display an SD card icon on the LCD in SETUP mode

(the SD card icon displayed after switching to SETUP mode will have a “lock” symbol inside it in it

if the card is locked). Formatting the SD card by using the Core Trail Camera “Format”

parameter before using it for the first time is recommended, especially when a card has been

used in other devices (see page 23, “Format” for details).

• To take out the SD card, just gently push in the card (do not try to pull it out without pushing in

first). The card is released from the slot and ready to be removed when you hear the click.

WARNING: Be sure the camera’s power is switched OFF before inserting or removing SD cards or

batteries.

USING THE Core Trail Camera

Once you’ve prepared your Core Trail Camera by properly installing batteries and an SD card, you could

simply take it outside, strap it to a tree, switch it on and leave-and you might get some great photos that

are exactly what you wanted.

However, we highly recommend that you first spend some additional time indoors with this manual and

your camera until you know a bit more about what the 3-way switch and directional keys do. If nothing

else, you’ll probably want to at least set the date and time so the camera will imprint them (or not-it’s

your option) on your photos as they are taken, learn how to set the camera to shoot video clips instead

of still photos if you like, and read some tips about mounting it on a tree.

THE OFF, ON, AND SETUP MODES

The Core Trail Camera has three basic operational modes:

• OFF mode: Power switch in the OFF position.

• ON mode: Power switch in the ON position (LCD screen is off.)

• SETUP mode: Power switch at SETUP position (LCD screen is on).

9

OFF MODE

The OFF mode is the “safe” mode when any actions must be taken, e.g., replacing the SD card or

batteries, or transporting the device. You will also use OFF mode if you connect the camera to a

computer’s USB port later to download your photos/ videos. And of course, when you are storing or not

using the camera, you will switch it to OFF. Please note that even in the OFF mode the Core Trail

Camera still consumes power at a very low level. Therefore, it’s a good idea to take the batteries out of

the battery compartment if the camera will not be used for a long time.

ON MODE

Anytime after the batteries and SD card have been inserted, you can switch on the camera. When the

power switch is moved to the top position, the camera will enter into the ON (Live) mode. The motion

indicator LED (pg. 6, “Front View”) will blink red for about 10 seconds. This interval allows time for you

to close the Core Trail Camera’s front cover, lock it, and leave the monitored area. Once in the ON

mode, no manual controls are needed or possible (the control keys have no effect). The Core Trail

Camera will take photos or videos automatically (according to its current parameter settings) when it is

triggered by the PIR sensor’s detection of activity in the area it covers.

You can either move the power switch directly from OFF to ON mode, or stop at the SETUP position first

to change one or more settings, then move the switch to ON after you have finished doing so.

SETUP MODE

In the SETUP mode you can check and change the settings of the Core Trail Camera’s with the help of its

built-in LCD. These settings, found in the SETUP Menu, let you change the photo or video resolution,

interval between photos, switch the time imprint on, etc. Moving the power switch to the SETUP

position will turn on the LCD display, and you will see an information screen that shows how many

images have been taken, the battery level, camera or video mode, etc (Fig. 3, next page).

NOTE: Always move the power switch from OFF to SETUP mode. It is possible that the camera could

lockup if it is switched from ON to SETUP mode. If this occurs, simply move the switch to OFF and then

push it up to SETUP again.

SETUP Mode Shortcut Keys/Functions

As mentioned earlier in “Parts & Controls”, four of the directional keys beside the LCD have secondary,

“shortcut” functions when the camera is switched to SETUP mode (but the MENU key has not been

pressed):

• Press the UP key to quickly set the camera to shoot video clips.

• Press the DOWN key to quickly set the camera to take still photos.

• Press the RIGHT key to manually trigger the shutter. This is useful for testing the camera-make sure

you are in SETUP mode, press the RIGHT key, and a few seconds later a photo or video (depending on

how the camera was set) will be saved to the SD card (or internal memory if no card is inserted). The

“number of images taken” counter on the bottom left of the LCD will increase by one. If the display

indicates “SD LOCKED” when you press the SHOT key, switch the camera OFF, remove the SD card and

slide its lock switch off.

10

Fig. 3: SETUP Information Screen (119936C/119938C)

USING THE SETUP MENU TO CHANGE SETTINGS

The main purpose of the SETUP mode is to allow you to change the settings of the camera’s parameters

(available parameters vary with use of Presets-see pg. 18 for more details) so your Core Trail Camera

operates exactly the way you want it to. You will do this by entering the SETUP Menu and pressing the

keys beside the LCD display, which will show you each parameter and its setting.

Changing Parameter Settings in SETUP Mode

A wide range of options or “parameters” are provided to allow you to set the Core Trail Camera to your

operational preferences. To change the setting of any parameter you must first switch to the SETUP

mode. Once in SETUP mode, pressing the MENU button will allow you to select any parameter and

change its setting. The name of the parameter and its current setting will be shown on the LCD.

Pressing the RIGHT or LEFT key scrolls to the next or previous parameter (RIGHT key to move on to the

next parameter and LEFT key to go back to the previous parameter), and pressing the UP or DOWN key

lets you select a different setting for the currently displayed parameter. Once you have selected your

preferred new setting for a parameter, press the ENTER button to save the new setting (actually change

it). When you are finished changing the settings of one or more parameters, press MENU again to exit

the SETUP menu. MENU can also be pressed anytime you want to cancel changing a parameter’s setting

after a new setting has been selected (but OK has not been pressed yet). After setting the parameters to

your preferences, be sure to move the switch to ON to begin actually taking photos or videos. No images

will be captured if the switch is left in the SETUP position (unless you press the RIGHT/Shot key after

exiting the menu)-in fact, the camera will power off automatically after a few minutes with no key

pressed.

Parameter Settings Display

The settings for each parameter are shown on the display screen of your Core Trail Camera. Only one

setting is displayed at a time, starting with the current setting for the parameter when it is first selected

(pg. 13, Fig. 4a). To change the setting, use the UP/DOWN keys to display the new setting you want (Fig.

4b), then press ENTER to “Execute” (make the actual change to this setting). If you want to confirm this

setting is now the current one, just press the RIGHT key to scroll to the next parameter, then press LEFT

to go back again to the previous one. You should see the parameter setting you just made.

11

Fig. 4 Selecting Parameter Settings

Press Menu

(4A)

Press Down

(4B)

Press OK

EXAMPLES-Changing the Settings of Some Common Parameters

Following this page, you will find tables listing all of the parameters found in the SETUP Menu, along

with their possible settings (or range of settings), and a detailed description of what the parameter

controls and what the settings do. If you read the previous section detailing how to select parameters

and change their settings, you should be able to dive right in, find the parameter(s) you want, and setup

the camera to suit your preferences. But maybe you’d rather walk through an example or two first:

To change any parameter’s setting, always start with the power switch in the SETUP position. After the

LCD comes on, press the MENU key.

The first parameter you will see when you enter the SETUP Menu is “Set Clock”. As the Time Stamp

feature is “On” by default, the camera will normally imprint the date and time on each photo or video,

based on your settings here. Press ENTER and use the UP/DOWN keys to set the hour (24-hr format,

“00”=midnight, “12”=noon), then press the RIGHT key move to the minute field and set it (again using

UP/DOWN). Press RIGHT to move to the lower row and set the year, month and date using the same

method. When finished, press the ENTER key to confirm the new time and date settings you made.

Now press the RIGHT key one time to move to another parameter in the Menu. The parameter you will

see is “Mode”. To change it from its default setting of “Camera” (still photos) to “Video” (shoot video

12

clips), press the DOWN key to select the “Video” setting. Press the ENTER key to “Execute” (Set) the new

setting you’ve selected for this parameter.

Now press the RIGHT key to move to another parameter in the Menu. Pressing it three times will take

you to “Video Size”. Try using the UP and DOWN keys to scroll through the range of settings, then press

ENTER to lock in your setting for the resolution of each video clip the camera shoots.

Pressing the RIGHT key several more times will get you to the “Default Set” parameter. Highlight or

select “Execute” (using UP or DOWN) and press ENTER to restore all parameters (including the Mode

and Video Size parameters you changed a minute ago) back to their original factory default settings. The

default settings for each parameter are indicated in bold type in the SETUP Menu tables on the next

several pages.

Field Scan 2x with Live Trigger Feature

Field Scan is a revolutionary new feature for the Bushnell Core Trail Camera, which allows you to

monitor your food plots or field edges with time lapse images or video. When set to “On”, the Core Trail

Camera will take a photo (or record a video clip) automatically at your choice of intervals (for example,

once every five minutes) during one or two blocks of time you set up for each day, without requiring a

trigger from an active animal. This has the advantage of giving you the ability to monitor the edge of a

field that might be 50 or 150 yards away from the camera out of the PIR sensor’s range. The result is an

effective range much greater than it would normally be, with the camera dependent on triggers

generated by nearby animals. This is a great tool for hunters to scout an entire field with only one

camera.

If an animal does enter the area covered by the PIR sensor and generate a trigger event during a time in

between the Field Scan intervals you set, the camera will capture an image or video just as it normally

would, based on your other menu settings. Here’s how to setup and use Field Scan (be sure you’ve set

the current time in “Set Clock” first, so your Field Scan recording will stop and start at the correct times

of day):

1. Move the main switch to SETUP, then press MENU.

2. Keep pressing the RIGHT key, stepping through the Setup Menu until you reach

Field Scan.

3. Press the UP key to select On, and press OK (Step 1, pg.17). You will see "A", representing the first

block of time you can define (a second block of time later in the day, "B" can also be setup if you wish).

Press OK (Step 2). This takes you to the screen to set Start and Stop times, which determines the clock

times when the first block of Field Scan recording will begin and end for each day.

You can set these times to the exact hour and minute you want, for a recording “window” that lasts

anywhere from just a minute to a full 24 hours.

4. Set the [Start] and [Stop] times, beginning with the Start hour, using the UP/DOWN keys to change

the setting (Step 3). The hour setting is based on a 24-hour clock, with “00” hours = midnight, “12” hours

= noon, “23” hrs = 11PM, etc. To move to the next setting, press the RIGHT key, change the minute for

the Start time with UP/DOWN, then on to the hour and minute settings for the Stop time.

5. After you finish setting the Stop minutes, press OK to confirm your settings for the first block of Field

Scan recording. If desired, you can create a second block of time by pressing the DOWN key to select "B"

(Step 4), then press OK and follow the same process to set Start and Stop times for Field Scan block "B"

13

(Step 5). As an example of how you might use these two available time blocks, you could setup Field

Scan time block "A" for the dawn hours from 6 AM to 8 AM, and block "B" to capture images between

5:30 and 7 PM. No Field Scan recording would occur from 8AM to 5:30PM, or from 7PM to 6AM.

6. After setting Start/Stop times to define Field Scan block "A" and/or "B", press OK, then press the UP

or DOWN key to select "Interval" and press OK (Step 6). The Field Scan "Interval" setting lets you control

how often a photo or video clip is recorded during the block(s) of time you defined with the Start and

Stop settings. Your options are 60 minutes, 30 minutes, 15 minutes, 5 minutes (default setting, also the

lowest interval in video mode), or 1 minute (still photo mode only). Use the UP/DOWN keys to select

your preference, then press OK to save it (Step 7). Note that for videos, "Interval" is independent of the

Length of each video recording-it’s how often videos are recorded, not how long each one lasts. 7.

Here’s an example of how the camera would operate, based on the following

Field Scan settings:

Field Scan: On

Field Scan A:

[Start]: 6:00

[Stop]: 8:00

Field Scan B:

[Start]: 17:30

[Stop]: 19:00

Interval: 15M

Note: avoid any "overlap" of Field Scan A & B recording blocks when setting their start and stop times,

to assure correct operation. Also-if the "Camera Mode" menu parameter is set to "Day" or "Night"

operation only, that will take priority over your Field Scan settings. Set the Camera Model to "24 HR" if

you are setting both day and night start and/or stop times in Field Scan.

These settings would cause the camera to capture a photo (or video, if the camera is set to that mode)

once every 15 minutes, beginning at 6 AM, until the Field Scan "A" recording block stops at 8:00 AM.

Later that day, the camera would again take a photo or video every 15 minutes between 5:30 PM and

7:00 PM (during Field Scan time block "B"). The next day, the camera would again record an image or

video once every 15 minutes between 6:00 and 8:00 AM, and between 5:30 and 7:00 PM. No Field Scan

recording would occur from 8AM to 5:30PM, or from 7PM to 6AM. Remember, Field Scan recording is

independent of normal triggers due to animal activity–even if no animals enter

the IR sensor coverage zone, an image or video will still be captured every 15 minutes during the

block(s) of time. If an animal triggers the camera “in between” the 15 minute intervals, it will be

recorded.

Note: Field Scan settings of frequent intervals and/or long periods between start and stop time can

reduce battery life.

14

The SETUP Menu – Parameters and Settings List w/Descriptions

Parameter

Settings (Bold=default)

Description

Set Clock

(Set)

Press OK and use the UP/DOWN keys (to change

the setting) and LEFT/RIGHT keys (to move to the

next field) to set the hour (24-hr format only,

“00”=midnight, “12”=noon) and minute, and then

(on the lower row), the year, month and date.

Mode

Camera, Video

Selects whether still photos or video clips are

captured when the camera is triggered

Image Size (only

affects still photos

in Camera)

3MP, 8MP, 24MP/30MP

(119975C/119977C Only)

Selects resolution for still photos. Higher

resolution provides more pixels, but creates

larger files that take up more of the SD card

capacity (fills up faster).

3MP, 8MP, 24MP, 30MP

15

Capture Number

(only affects

still photos

in Camera mode)

1 Photo, 2 Photo, 3 Photo, 4

Photo, 5 Photo

Selects how many photos are taken in sequence

per trigger in Camera mode. This setting affects

photos taken in Field Scan mode as well (to snap

two photos every 10 minutes, for example). Note:

only one photo will be captured if "Interval" is set

to 0.6 second, regardless of the Capture Number

setting. Please also refer to the Interval

parameter.

Video Size (only

affects video clips

in Video mode)

1920x1080 60FPS

(119975C/119977C only)

1920x1080

1280x720

640x360

Selects video resolution (in pixels per frame).

Higher resolution produces better quality videos,

but creates larger files that take up more of the

SD card capacity (fills up faster). 640x360 is VGA

video in "widescreen" 16:9 format. The highest

setting provides HD video. Using high speed SD

cards (SanDisk® SDHC class 6 or higher) is

recommended if you will use the 1280x720 or

1920x1080 video settings.

Video Length

(only affects video

clips in Video

mode)

5S to 60S fixed time range

(10S default), or Dynamic

variable length

Sets length per video clip. The default setting is

10 seconds fixed time per video, with an available

range from 5S (5 seconds) to 60S (1 minute).

Nighttime limit of 15 seconds when LED Control =

High.

The "Dynamic" setting provides a variable video

length, based on animal activity within PIR range

and your Interval (next page) and LED

Control settings as follows:

With Interval set to 0.6 sec: video length is a

fixed 10 seconds per trigger. If a new trigger

occurs during the last 4 seconds of a video,

another 10 second video will be recorded

immediately after the first. This will continue

indefinitely as long as battery power is adequate,

regardless of LED Control settings, during both

day and night time.

With Interval set to 2 sec or longer, for daytime

videos: video length is "adaptive" (determined by

new triggers), with a minimum of 5 seconds. If a

new trigger occurs during the last 4 seconds of

this first video, the length is extended by another

1-4 seconds (based on when the new trigger

happens), with a maximum total length of 2

minutes continuous video before a new video is

initiated.

With Interval set to 2 sec or longer, and LED

Control=High, for night videos: same as daytime,

but maximum length is 15 seconds before

16

recording ends and a new video is started if a

new trigger occurs.

With Interval set to 2 sec or longer, and LED

Control=Med/Low, for night videos: same as

daytime, but maximum length is 60 seconds

before recording ends and a new video is started

if a new trigger occurs.

Interval

10S (second) default, with

as60M (minute) to .2S (half

second) range of settings

available. (60M-1M are set

in one minute increments,

59S-3S are set in one second

increments, followed by the

.6S setting)

Selects the length of time that the camera will

“wait” until it responds to any additional triggers

from the PIR after an animal is first detected and

remains within the sensor’s range. During this

user set “ignore triggers” interval, the camera will

not capture photos/ videos. This prevents the

card from filling up with too many redundant

images. Settings begin with 10 second default

when parameter is first selected. Setting the

Interval time to .6 second will capture the

maximum # of images, but some may appear

"washed out" if animal is too close to camera at

night. Note: after setting down past “.6S”,

settings start over at “60M”.

Format

Execute (followed by an

additional No/Yes step)

Deletes (erases) all files stored on a card to

prepare it for reuse. Always format a card that

has been previously used in other devices.

Caution! Make sure you have downloaded and

backed up any files you want to preserve first!

Press OK to execute, press MENU (or select NO

then press OK) to exit without formatting.

Time Stamp

On, Off

Select “On” if you want the date & time (that the

image was captured) imprinted on every

photo/video, select “Off” for no imprint. Note:

the current temperature, moon phase, and (user

set) camera name will also be imprinted on your

still photos.

Video Sound

(Only affects

video clips in

Video mode)

On, Off

Select “On” to record audio along with the video

when the camera is set to video mode (saved file

sizes will be slightly larger).

Sensor Level

Auto, Low, Normal, High

Auto sensor level will automatically adjust the

sensor level depending on the surrounding

temperature. >70℉(High); 45℉～70℉(Normal);

< 45℉(Low), High Sensor will adjust the cameras

sensitivity to reach out 70’, Normal Sensor will

adjust the cameras sensitivity to reach out 100’,

17

Low Sensor will adjust the cameras sensitivity to

reach out 40’

Camera Mode

24 Hrs, Day, Night

Allows user to limit operation to only day or night

period if desired. An ambient light level sensor

determines "Day" vs "Night" automatically.

Default Set

Cancel, Execute

Select “Execute” and press OK to restore all

parameters to the original factory default

settings. If the camera is behaving oddly and you

think you may have changed the setting for

something accidently (but aren’t sure which one),

this will reset all parameters to their most

commonly used or “generic” settings.

Version

None

Displays current firmware version for reference.

USING THE SETUP MENU INPUT SCREENS

Camera Name Input

After selecting the Camera Name parameter (the only setting is "Input"), press OK.

If necessary, delete the previous or default name by pressing the RIGHT key until the backspace symbol (

) (located between letters "A" & "B", also between "j" & "k") is highlighted, then keep pressing OK.

Select (highlight) each alphanumeric character you want, using the LEFT/RIGHT keys, and pressing OK

after each one to set it. When finished naming the camera, press MENU to save the name to memory.

Coordinate Input

After selecting the Coordinate Input parameter, press UP or DOWN to select the On setting and press

OK. The latitude and longitude for any location where you plan to place the camera can be obtained at

many websites, for example: http://itouchmap.com/latlong.html . You can enter a nearby street

address, just zip code, or use the various types of maps to locate the approximate position. The format

you will need to use to enter the coordinates in the Core Trail Camera menu screen is shown below:

Note: You may see "negative" latitude or longitude coordinates online. These designate South latitudes

and West longitudes. US/Canada locations will have North (+) latitude coordinates and West (-)

longitude coordinates.

MOUNTING and POSITIONING the Core Trail Camera Mounting

After you’ve set up the camera’s parameters to your personal preferences at home or in your truck,

you’re ready to take it outside and slide the power switch to “ON”. When setting up the Core Trail

Camera for scouting game or other outdoor applications, you must be sure to mount it in place correctly

and securely.

We recommend mounting the Core Trail Camera on a sturdy tree with a diameter of about 6 in. (15cm).

To get the optimal picture quality, the tree should be about 16-17 ft. (5 meters) away from the place to

be monitored, with the camera placed at a height of 5-6.5 ft. (1.5~2 m). Also, keep in mind that you will

get the best results at night when the subject is within the ideal flash range, no farther than 100ft/30m

(119936C/1198838C) and no closer than 10ft (3m) from the camera.

There are two ways to mount the Core Trail Camera: using the provided adjustable web belt, or the

tripod socket.

18

Using the adjustable web belt: Fig. 5 illustrates using the web belt on the Core Trail Camera. Push one

end of the belt through the two brackets on the back of the Core Trail Camera. Thread the end of the

strap through the buckle. Fasten the belt securely around the tree trunk by pulling the end of the strap

firmly so there is no slack left. Using the tripod socket: The camera is equipped with a socket at the

bottom end to enable mounting on a tripod or other mounting accessories with a standard1/4-20

thread.

Fig. 5 Attaching the Belt

Note: an accessory solar panel supplemental power source (#119756C) is also available -

please visit www.bushnell.com for more information.

Sensing Angle and Distance Test

To test whether the Core Trail Camera can effectively monitor the area you choose, this test is

recommended to check the sensing angle and monitoring distance of the Core Trail Camera. To perform

the test:

• Switch the Core Trail Camera to the SETUP mode.

• Make movements in front of the camera at several positions within the area where you expect the

game or subjects to be. Try different distances and angles from the camera.

• If the motion indicator LED light blinks, it indicates that position can be sensed If it does not blink, that

position is outside of the sensing area. The results of your testing will help you find the best placement

when mounting and aiming the Core Trail Camera. The height away from the ground for placing the

device should vary with the animal size appropriately. In general, 3 to 6 feet is preferred.

You can avoid potential false triggers due to temperature and motion disturbances in front of the

camera by not aiming it at a heat source or nearby tree branches or brush (especially on windy days).

Switching ON the Camera

Once you switch to the ON mode, the motion indicator LED (red) will blink for about 10 seconds. This

gives you time to close and lock the front cover of the Core Trail Camera and then walk away. During

this time, the motion indicator LED will blink red continuously. After it stops blinking, the PIR is active,

and any motion that is detected by it will trigger the capture of photos or videos as programmed in the

SETUP Menu. Be sure you have read the descriptions of the Capture Number, Interval and Sensor Level

parameters. Please note, the PIR is strongly sensitive to ambient temperature. The greater the

temperature difference between the environment and your subject, the farther the possible sensing

distance. The average sensing distance is about 60 ft.

19

Before leaving the camera unattended, please check for the following:

• Are the batteries or DC power supply inserted/connected with correct polarity and is the power level

is sufficient?

• Does the SD card have sufficient available space and is its write-protection (lock) switch off?

• Is the Power switch in the ON position? (Do not leave it in SETUP).

REVIEWING/DELETING THE PHOTOS/VIDEOS

After you have setup, mounted and activated your Core Trail Camera, you will of course be eager to

return later and review the images it has captured for you. There are several different ways this can be

done.

Reviewing Images Directly From the SD Card

This is the most popular method of viewing images. Since unmounting the camera and taking it to your

computer isn’t very convenient, you may find it easier to just take the card out. By removing the SD card

(swapping it for a new empty card if you like) and taking it to your home or campsite to view the images

by using an SD card “reader” (user supplied) connected to your computer (some computers and TVs

have a built in SD card slot), you can leave the camera in place ready to capture more images. Once

connected, the card reader works the same way as described below-please read that section if you have

any problem finding your files.

Reviewing Images by Connecting the Camera to a Computer

You can always unmount the entire camera from the tree and connect its USB port to a computer-it will

be recognized as a “removable disk”, without the need to install any drivers or software. When using a

PC (or Mac*) to view photos (or video clips*), first connect the device to the computer with a USB cable

(not included, available at most electronics/computer retailers) that has a “Mini-B” USB plug on one end

(camera) and a “Standard-A” USB plug at the other end (computer). Then use commercial software with

an image browser feature, or an image browser included with the PC’s operating system to view images

saved on the SD card in the folder \DCIM\100EK113 (a new folder will be created every 1000 images).

Each new image or video will be numbered incrementally with 8 digits in order of the time it was

captured-the first 4 digits are the month and day, the last 4 digits the # of the image.

For example, you will see file names such as “09020001.JPG” or “09020001.MP4”, etc. Through the file

format suffix you can distinguish whether the file is a still photo (with suffix .JPG) or a video (with suffix

.MP4). *video files may require additional software for viewing on a Mac.

The Core Trail Camera supports 3 kinds of file system formats, FAT12, FAT16, and FAT32. The default

value is FAT16 to save photos and videos. Here are some related notes:

• You don’t need to be concerned about the file system format of the Core Trail Camera unless your

equipment has problems reading the SD card. If this happens, please format the SD card with the Core

Trail Camera or in your computer first and then insert the card into your Core Trail Camera and try

again.

• The default file system format of the Core Trail Camera is FAT16, which most computers can read. If

you format an SD card for the Core Trail Camera in your computer, you should choose the file system

20

format FAT16. Normally FAT16 is recommended unless you have another image viewer that uses FAT12

or FAT32 format.

Deleting Photos or Videos

To delete all photos from the installed SD card, use the Format parameter (see pg. 23 for details).

DOWNLOADING THE PHOTOS/VIDEOS

To download your photos/videos to a PC or Mac*, first make sure the Core Trail Camera power switch is

in the OFF position. Connect a USB cable to the camera’s USB port, then directly to a main USB port on

your computer-do not use front panel/keyboard USB ports or unpowered “hubs”.

The Core Trail Camera will be recognized as a standard “USB Mass Storage” device (this may take

several seconds the first time you connect it). If you would rather leave your camera in the woods and

just pull its SD card out, an SD card reader works the same way as described in this section once the card

is inserted and the reader is connected to your computer.

With Windows XP or later, you can then simply use the options in the pop-up window to copy, view, or

print your photos (right).

On all Windows OS, the Core Trail Camera will also be listed as a “Removable Disk” if you open the “My

Computer” window (on Macs, an icon will appear on your desktop).

The Core Trail Camera’s photo files are named “09020001.JPG” etc, and are located in the

“DCIM\100EK113” folder on this “Removable Disk”. Video file names will end with “.MP4”. You may

copy the photos/ videos to your hard drive as you would any file-just copy/paste or drag the file names

or icons to your drive or desktop.

After the photos are copied to your hard drive, you can disconnect the Core Trail Camera. (On Mac

computers, drag the “disk” that appeared on your desktop when the camera was connected into your

Trash to “eject” it before disconnecting.) The .JPG format photo files from the Core Trail Camera may be

viewed and edited with any photo software you choose to use. The .MP4 video files may be viewed with

the Windows Media Player on PCs with Windows 7. If your computer is running an older version of

Windows, or you are on a Mac, and you don’t already have a compatible video player, you can

download a free version of the DivX player from http://www.divx.com/.

21

TROUBLESHOOTING / FAQ

Camera takes continuous images of no subject

A camera has what is known as a “false trigger” if the PIR sensor thinks that there is motion and heat in

front of the camera lens when there is no subject in the image. These “False Triggers” are the result of

placing the camera in an environment where there is motion associated with tree branches creating

motion in front of the camera or an area where there is high heat in the foreground and any motion

from wind could set off the camera. Setting a camera up over water is also a potential cause for this

issue. To remedy this situation:

1. Try moving the camera to an area that does not have any of these issues or try changing the sensor

level on the menu settings.

2. If the camera continues to take images when there is no subject in them, try placing the camera in an

inside environment and aiming at a location where there is no motion.

3. If the camera continues to show issues, then there is probably an electronic component issue. If this is

the case, please contact our customer service to send the camera back for repair.

Battery life is shorter than expected

1. Battery life will vary with operating temperature and the number of images taken over time. Setting

the Interval time to 0.6 second will decrease battery life. Typically, the Core Trail Camera will be able to

capture several thousand images before the batteries die.

2. Check to make sure you have used new alkaline or lithium batteries. Bushnell recommends using

Energizer® Lithium AA batteries in your Core Trail Camera model to obtain maximum battery life.

3. Make sure that the power switch was turned to the “On” position and that the camera was not left in

“Setup” mode while in the field.

4. Make sure that you are using a good quality name brand SD card in your camera.

Bushnell recommends SanDisk® brand SD Cards up to 32GB (Ultra® or

Extreme® series for HD video). Our experience indicates that poor quality SD cards can sometimes

reduce your Core Trail Camera battery life.

Camera stops taking images or won’t take images

1. Please make sure that the SD card is not full. If the card is full, the camera will stop taking images.

2. Check the batteries to make sure that they are new alkaline or lithium AA batteries. See note above

about short battery life.

3. Make sure that the camera power switch is in the “On” position and not in the “Off” or “Setup”

modes.

4. Make sure that you are using a good quality SD card in your camera. Bushnell recommends SanDisk®

SD Cards up to 32GB (Ultra® or Extreme® series for HD video).

5. If the SD card has its write protect switch in the lock position, the camera will not take images.

6. If you have used an SD card in another device before inserting it in your Core Trail Camera, you might

want to try formatting the card using the “Format” parameter in Setup mode (make sure you have

backed up any important files first, as formatting will erase all previous files). In some cases, other

devices may change the formatting of the SD card so that it will not work properly with the Core Trail

Camera.

La pagina sta caricando ...

Bushnell Core DS Istruzioni per l'uso

Questo manuale è adatto anche per

Bushnell Core DS Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti