Bushnell Prime Trail 119932C 119932CB Manuale utente

PRIME TRAIL CAMERA

INSTRUCTION MANUAL

Model# 119932C / 119932CB 08-20

2

IMPORTANT NOTE

Congratulations on your purchase of one of the best trail camer-

as on the market! Bushnell is very proud of this little unit and we

are sure you will be pleased with it as well. We appreciate your

business and want to earn your trust. Please refer to the notes

below and the instructions in this manual to ensure that you are

completely satisfied with this product.

If your Bushnell Prime Trail Camera does not seem to be

functioning properly or if you are having photo/video quality

issues, please check the Troubleshooting/FAQ section.

Problems are often due to something simple that was

overlooked, or require only changing one setting to solve.

If your problem continues after trying the solutions in the

Troubleshooting/FAQ section, please call Bushnell Customer

Service at (800) 423-3537. In Canada, call (800) 361-5702. For

EU owners, email: [email protected]

Bushnell recommends using 6 Energizer® Lithium AA batteries

in this Prime Trail Camera model to obtain maximum battery life.

Do not mix old and new batteries.

Do not mix battery types-use ALL lithium or ALL alkaline.

Rechargeable batteries are NOT recommended.

Bushnell recommends using SanDisk® SD and SDHC Cards (up

to 32GB capacity) in all Prime Trail Camera.

3

INTRODUCTION

About the Prime Trail Camera

The Bushnell Prime Trail Camera is a digital scouting camera. It can be triggered

by any movement of game in a location, detected by a highly sensitive Passive

Infra-Red (PIR) motion sensor, and then take high quality pictures (up to 24MP still

photos), or 720p HD video clips.

The Prime Trail Camera consumes very little power (less than 0.08 mA) in a stand-

by (surveillance) state. This means it can deliver up to twelve months stand-by

operation time when the device is powered by six AA alkaline batteries. Once

motion in the monitored area is detected, the digital camera unit will be triggered at

once (typically less than half a second) and then automatically take images

according to previously programmed settings. The Prime Trail Camera is equipped

with built-in infrared LEDs that function as a flash, so that it delivers clear photos or

videos (in black & white) even in the dark, and it can take color photos or videos

under sufficient daylight. The Prime Trail Camera is designed for outdoor use and

is resistant against water and snow.

Applications

The Prime Trail Camera can be used as a trail camera for hunting or scouting

game. It is also suitable for surveillance usage.

PARTS AND CONTROLS

The Prime Trail Camera provides the following connections for external devices:

USB port and SD card slot (Fig. 4).

A 3-way power switch is used to select the main operating modes: OFF, AIM, and

ON (Fig. 3).

A D-Pad interface with 5-way keys is primarily used in AIM mode to select

operational functions and parameters. As shown in Fig. 3, these keys are: UP,

DOWN, LEFT, RIGHT, OK and MENU. Three of the keys can also perform a second

function (shortcut operations in AIM mode) in addition to their main function: The

DOWN key can be used to set the camera to Photo mode (still camera icon), and

the UP key can set the camera to Video mode (movie camera icon). The RIGHT key

also serves as the manual shutter (“SHOT”) button of the camera. These second-

ary functions are indicated by icons or text above the key as shown in Fig. 3.

4

Fig. 1

Fig. 2

5

Fig. 3

Fig. 4

6

INSTALLING THE BATTERIES AND SD CARD

Before you begin learning how to use your Prime Trail Camera, you will first need

to install a set of batteries and insert an SD card. Although that may only take you a

minute, there are some important notes about both batteries and SD cards you

should be aware of, so please take the time to read the following directions and

cautions:

Loading Batteries

After opening the latch on the right side of the Prime Trail Camera, you will see that

the Prime Trail Camera has a battery release button. Depress this button and a

battery tray will drop out of the bottom of the camera. The battery tray will stop about

½ inch out of the device, this is a latch system to prevent the tray from dropping onto

the ground. Just apply a little pressure when pulling and the tray will release. The

battery tray has six battery slots. Install a full set of 6 batteries. Be sure to insert

each battery with correct polarity (negative or “flat” end against the long spring of

each battery slot).

Bushnell recommends using a full set of new lithium AA (Energizer® brand) or

alkaline AA batteries. NiMh Rechargeable batteries are not recommended, as the

lower voltage they produce can cause operational issues.

You can also connect an optional Solar Panel accessory (model# 119756C –please

visit www.bushnell.com for more information) to the “DC In” jack at the bottom of the

Prime Trail Camera (other external power supplies should not be used, as the

camera and/or display may not function correctly). If the solar panel is connected

and AA batteries are installed, the Prime Trail Camera will be powered by the solar

panel's rechargeable lith-ion battery, as long as it provides adequate voltage (if not,

the camera will switch to battery power). The solar panel's battery will power the

camera at night.

7

Inserting the SD Card

Insert the SD card (with the camera’s power switch in the OFF position) before

beginning to operate the camera. Don’t insert or remove the SD card when the

power switch is in the ON position.

The Prime Trail Camera uses a standard SD (Secure Digital) memory card to save

photos (in .jpg format) and/or videos (in .avi format). SD and SDHC (High Capacity)

cards up to a maximum 32GB capacity are supported. Before inserting the SD card

into the card slot after opening the camera’s front cover, please make sure that the

write- protect switch on the side of the card is “off” (NOT in the “Lock” position). The

following describes how to insert and remove the SD card:

• Insert the SD card into the card slot with its label side upwards (see above). A

“click” sound indicates that the card is installed successfully. If the wrong side of the

card is facing up, you will not be able to insert it without force-there is only one

correct way to insert cards. If the SD card is not installed correctly, the device will

not display an SD card icon on the LCD in SETUP mode (the SD card icon displayed

after switching to SETUP mode will have a “lock” symbol inside it in it if the card is

locked). Formatting the SD card by using the Prime Trail Camera “Format”

parameter before using it for the first time is recommended, especially when a card

has been used in other devices (see “Changing Menu Parameter Settings” for

details).

• To take out the SD card, just gently push in the card (do not try to pull it out

without pushing in first). The card is released from the slot and ready to be removed

when you hear the click. Be sure the camera’s power is switched OFF before

inserting or removing SD cards or batteries.

8

USING THE Prime Trail Camera

Once you’ve prepared your Prime Trail Camera by properly installing batteries and

an SD card, you could simply take it outside, strap it to a tree, switch it on and leave-

and you might get some great photos that are exactly what you wanted.

However, we highly recommend that you first spend some additional time indoors

with this manual and your camera until you know a bit more about what the 3-way

switch and direction keys do. If nothing else, you’ll probably want to at least set the

date and time so the camera will imprint them (or not-it’s your option) on your photos

as they are taken, learn how to set the camera to shoot video clips instead of still

photos if you like, and read some tips about mounting it on a tree.

THE OFF, ON, AND AIM MODES

The Prime Trail Camera has three basic operational modes:

• OFF mode: Power switch in the OFF position.

• ON mode: Power switch in the ON position (LCD screen is off.)

• AIM mode: Power switch at AIM position (LCD screen is on).

OFF MODE

The OFF mode is the “safe” mode when any actions must be taken, e.g., replacing

the SD card or batteries, or transporting the device. You will also use OFF mode if

you connect the camera to a computer’s USB port later to download your

photos/videos. And of course, when you are storing or not using the camera, you

will switch it to OFF. Please note that even in the OFF mode the Prime Trail Camera

still consumes power at a very low level. Therefore, it’s a good idea to take the

batteries out of the battery compartment if the camera will not be used for a long time.

ON MODE

Any time after the batteries and SD card have been inserted, you can switch on the

camera. When the power switch is moved to the far left position, the camera will

enter into the ON (Live) mode. The motion indicator LED (Fig.1, “Front View”) will

blink red for about 10 seconds. This interval allows time for you to close the Prime

Trail Camera’s front cover, lock it, and leave the monitored area. Once in the ON

mode, no manual controls are needed or possible (the control keys have no effect).

The Prime Trail Camera will take photos or videos automatically (according to its

current parameter settings) when it is triggered by the PIR sensor’s detection of

activity in the area it covers.

9

You can either move the power switch directly from OFF to ON mode, or stop at the

AIM position first to change one or more settings, then move the switch to ON after

you have finished doing so.

AIM MODE

In the AIM mode you can check and change the settings of the Prime Trail Camera

with the help of its built-in LCD. These settings, found in the SETUP Menu, let you

change the photo or video resolution, interval between photos, switch the time

imprint on, etc. Moving the power switch to the AIM position will turn on the LCD

display, and you will see an information screen that shows how many images have

been taken, the battery level, camera or video mode, etc (see Fig. 5).

NOTE: Always move the power switch from OFF to AIM mode. It is possible that the

camera could lockup if it is switched from ON to AIM mode. If this occurs, simply

move the switch to OFF and then push it up to AIM again.

AIM Mode Shortcut Keys/Functions

As mentioned earlier in “Parts & Controls”, three of the keys below the LCD have

secondary, “shortcut” functions when the camera is switched to AIM mode (but the

MENU key has not been pressed):

• Press the UP key to quickly set the camera to shoot video clips.

• Press the DOWN key to quickly set the camera to take still photos.

• Press the RIGHT key to manually trigger the shutter. This is useful for testing

the camera-make sure you are in AIM mode, press the RIGHT key, and a few

seconds later a photo or video (depending on how the camera was set) will be saved

to the SD card. The “number of images taken” counter on the bottom left of the LCD

will increase by one. If the display indicates “SD PROTECTED” when you press the

SHOT key, switch the camera OFF, remove the SD card and slide its protect switch

off.

Fig.5: SETUP Information Screen

10

USING THE SETUP MENU TO CHANGE SETTINGS

The main purpose of the AIM mode is to allow you to change the settings of the

camera’s parameters so your Prime Trail Camera operates exactly the way you

want it to. You will do this by entering the SETUP Menu and pressing the keys

beside the LCD display, which will show you each parameter and its setting.

Changing Parameter Settings in SETUP Mode

A wide range of options or “parameters” are provided to allow you to set the Prime

Trail Camera to your operational preferences. To change the setting of any

parameter you must first switch to the AIM mode. Once in AIM mode, pressing the

MENU button will allow you to select any parameter and change its setting. The

name of the parameter and its current setting will be shown on the LCD. Pressing

the RIGHT or LEFT key scrolls to the next or previous parameter (RIGHT key to

move on to the next parameter and LEFT key to go back to the previous parame-

ter), and pressing the UP or DOWN key lets you select a different setting for the

currently displayed parameter. Once you have selected your preferred new setting

for a parameter, press the OK button to save the new setting (actually change it).

When you are finished changing the settings of one or more parameters, press

MENU again to exit the SETUP menu. MENU can also be pressed anytime you

want to cancel changing a parameter’s setting after a new setting has been selected

(but OK has not been pressed yet). After setting the parameters to your preferences,

be sure to move the switch to ON to begin actually taking photos or videos. No

images will be captured if the switch is left in the AIM position (unless you press the

RIGHT/Shot key after exiting the menu) - in fact, the camera will power off

automatically after a few seconds with no key pressed.

To make the Parameter Settings easier, we have made the camera with 3 basic

settings (Set Clock / Mode / Interval) and an “Additional Set” which allows custom-

er to access to the full suite of settings if you turn the “Additional Set” on.

11

Parameter Setting Display

The settings for each parameter are shown on the display screen of your Prime

Trail Camera. Only one setting is displayed at a time, starting with the current

setting for the parameter when it is first selected (Fig. 6a). To change the setting,

use the UP/DOWN keys to display the new setting you want (Fig. 6b), then press

OK to “Execute” (make the actual change to this setting). If you want to confirm this

setting is now the current one, just press the RIGHT key to scroll to the next

parameter, then press LEFT to go back again to the previous one. You should see

the parameter setting you just made.

Fig. 6: Selecting Parameter Settings

Press Menu

(6a)

Press DOWN to select new setting for the highlighted parameter

(6b)

Press OK to confirm and execute the new setting

12

EXAMPLES-Changing the Settings of Some Common Parameters

Following this page, you will find tables listing all of the parameters found in the

SETUP Menu, along with their possible settings (or range of settings), and a

detailed description of what the parameter controls and what the settings do. If you

read the previous section detailing how to select parameters and change their

settings, you should be able to dive right in, find the parameter(s) you want, and

setup the camera to your preferences. But maybe you’d rather walk through an

example or two first:

To change any parameter’s setting, always start with the power switch in the AIM

position. After the LCD comes on, press the MENU key.

The first parameter you will see when you enter the SETUP Menu is “Set Clock”. As

the Time Stamp feature is “On” by default, the camera will normally imprint the date

and time on each photo or video, based on your settings here. Press OK and use

the UP/DOWN keys to set the hour (24- hr format, “00”=midnight, “12”=noon), then

press the RIGHT key move to the minute field and set it (again using UP/DOWN).

Press RIGHT to move to the lower row and set the year, month and date using the

same method. When finished, press the OK key to confirm the new time and date

settings you made.

Now press the RIGHT key to move to another parameter in the Menu. The next

parameter you will see is “Mode”. To change it from its default setting of “Camera”

(still photos) to “Video” (shoot video clips), press the DOWN key to select the

“Video” setting. Press the OK key to “Execute” (Set) the new setting you’ve selected

for this parameter.

Now press the RIGHT key to move to another parameter in the Menu. Pressing

it 2 times will take you to “Additional Set”. Try using the UP and DOWN keys to

choose to turn ON / OFF the “Additional Set”. You will get to the full suite of

settings if you turn the “Additional Set” on.

Field Scan 2x with Live Trigger Feature

Field Scan is a revolutionary new feature for the Bushnell Prime Trail Camera,

which allows you to monitor your food plots or field edges with time lapse images.

When set to “On”, the Prime Trail Camera will take a photo automatically at your

choice of intervals (for example, once every five minutes) during one or two blocks

of time you set up for each day, without requiring a trigger from an active animal.

This has the advantage of giving you the ability to monitor the edge of a field that

might be 50 or 150 yards away from the camera out of the PIR sensor’s

13

range. The result is an effective range much greater than it would normally be, with

the camera dependant on triggers generated by nearby animals. This is a great tool

for hunters to scout an entire field with only one camera.

Here’s how to setup and use Field Scan (be sure you’ve set the current time in “Set

Clock” first, so your Field Scan recording will stop and start at the correct times of

day):

1. Move the main switch to AIM, then press MENU.

2. Keep pressing the RIGHT key, stepping through the Setup Menu until you reach

“Additional Set” and turn it on. Then keep pressing the RIGHT key until you reach

Field Scan.

3. Press the UP key to select On, and press OK (Step 1), you will see “Interval”.

Then press OK key entering into the interval settings. The Field Scan "Interval"

setting lets you control how often a photo is captured during the block(s) of time you

defined with the Start and Stop settings. Your options are 60 minutes, 30 minutes,

15 minutes, 5 minutes (this is the default), or 1 minute. Use the UP/DOWN keys

to select your preference, then press OK to save it (Step 7). Then press DOWN key,

you will see "A", representing the first block of time you can define (a second block

of time later in the day, "B" can also be setup if you wish). Press OK (Step 2). This

takes you to the screen to set Start and Stop times, which determines the clock

times when the first block of Field Scan recording will begin and end for each day.

You can set these times to the exact hour and minute you want, for a recording

“window” that lasts anywhere from just a minute to a full 24 hours.

4. Set the [Start] and [Stop] times, beginning with the Start hour, using the

UP/DOWN keys to change the setting (Step 3). The hour setting is based on a 24-

hour clock, with “00” hours = midnight, “12” hours

= noon, “23” hrs = 11PM, etc. To move to the next setting, press the RIGHT key,

change the minute for the Start time with UP/DOWN, then on to the hour and minute

settings for the Stop time.

5. After you finish setting the Stop minutes, press OK to confirm your settings for

the first block of Field Scan recording. If desired, you can create a second block of

time by pressing the DOWN key to select "B" (Step 4), then press OK and follow

the same process to set Start and Stop times for Field Scan block "B" (Step 5). As

an example of how you might use these two available time blocks, you could setup

Field Scan time block "A" for the dawn hours from 6 AM to 8 AM, and block "B" to

capture images between 5:30 and 7 PM. No Field Scan recording would occur from

8AM to 5:30PM, or from 7PM to 6AM.

6. Here’s an example of how the camera would operate, based on the following

14

Field Scan settings:

Field Scan: On

Field Scan A: [Start]: 6:00 [Stop]: 8:00

Field Scan B: [Start]: 17:30 [Stop]: 19:00

Interval: 15M

Note: avoid any “overlap” of Field Scan A & B recording blocks when setting their

start and stop times, to assure correct operation.

These settings would cause the camera to capture a photo once every 15 minutes,

beginning at 6 AM, until the Field Scan "A" recording block stops at 8:00 AM. Later

that day, the camera would again take a photo every 15 minutes between 5:30 PM

and 7:00 PM (during Field Scan time block "B"). The next day, the camera would

again record an image once every 15 minutes between 6:00 and 8:00 AM, and

between 5:30 and 7:00 PM. No Field Scan recording would occur from 8AM to

5:30PM, or from 7PM to 6AM. Remember, Field Scan recording is independent of

normal triggers due to animal activity – even if no animals enter the IR sensor

coverage zone, an image will still be captured every 15 minutes during the block(s)

of time. Note: Field Scan settings of frequent intervals and/or long periods between

start and stop time can reduce battery life.

15

The SETUP Menu – Parameters and Setting List w / Descriptions

Parameter

Settings

(Bold=default)

Description

Set Clock

Set

Press OK and use the UP/DOWN

keys (to change the setting) and

LEFT/RIGHT keys ( to move to the

next field) to set the hour (24-hr format

only, “00”=midnight, “12”=noon) and

minute, and then (on the lower row),

the year, month and date.

Mode

Camera or Video

Selects whether still photos or video

clips are captured when the camera

is triggered.

Interval

5S(second) default, with

a 60M (minute) to 1S

(second)

range of settings

available.

(60M-1M are set in one

minute increments,

59S-1S are set in one

second increments)

Selects the length of time that the

camera will “wait” until it responds to

any additional triggers from the PIR

after an animal is first detected and

remains within the sensor’s range.

During this user set “ignore triggers”

interval, the camera will not capture

photos/videos. This prevents the

card from filling up with too many

redundant images. Settings begin

with the default 5 seconds when

parameter is first selected.

Notes: after setting down past “1S”,

settings start over at “60M”.

Setting the Interval time to 1 second

will capture the maximum # of

images, but some may appear

"washed out" if animal is too close to

camera at night.

Addition Set

On or Off

Select ON to access to the full suite

of settings.

16

Image Size

(only affects still photos)

3M=2304x1296

12M=4608x2592

24M=6528x3672

Selects resolution for still photos.

Higher resolution provides more

pixels, but creates larger files that take

up more of the SD card capacity (fills

up faster). 12M is a good compromise

between resolution and file size.

Capture Number

(only affects still photos)

1 Photo, 2 Photo,

3 Photo, 4 Photo,

5 Photo

Selects how many photos are taken

in sequence per trigger in Camera

mode. Please note that the capture

number can only be set to 1 photo

when the Field Scan is On.

Video Size

(only affects video clips)

1920x1080 15FPS

1280x720 30FPS

640x368 30FPS

Selects video resolution (in pixels per

frame). Higher resolution produces

better quality videos, but creates

larger files that take up more of the

SD card capacity (fills up faster).

640x368 is VGA video in widescreen

16:9 format. The highest setting

provides HD video. Using high speed

SD cards (SanDisk® SDHC class 6

or higher) is recommended if you will

use the 1280x720 or 1920x1080

video settings.

Video Length

(only affects video clips)

10S (second)

default, with 60S

to 5S possible

range

Sets length per captured video clip.

Settings begin with 10 second default

when parameter is first selected. After

stepping down to 5S, video length

settings start over at 60S.

17

Sensor Level

Low, Normal, High

Selects the sensitivity of the PIR

sensor. The “High” setting will make

the camera more sensitive to infrared

(heat) and more easily triggered by

motion, and the “Low” setting makes it

less sensitive to heat and motion. The

High setting can be useful when the

ambient temperature is warm (making

it more difficult for the sensor to detect

animals), and the Low setting may

help in cold weather if the camera is

being triggered too often by anything

warmer than the surroundings.

“Normal” is for average or moderate

conditions.

Field Scan

On, Off (After On

is selected): “A”

Start/Stop, “B”

Start/Stop,

Interval

Turns Field Scan (Time Lapse)

recording mode on/off. When

activated, Field Scan forces the

camera to take photos even when it

is not triggered by a nearby live

animal, useful for constant monitor-

ing of an area that might be far away

from the camera. The user can set

the start and stop times for up to two

independent “blocks” of Field Scan

recording, as well as the interval time

between each photo. To ensure

correct operation, avoid setting

overlapping start/stop times for Field

Scan A and B. Please read the “Field

Scan 2x…” section of this manual for

details on using this feature.

18

Flash mode

Auto,

Long Range, Fast

Motion

Long Range - High LED output Low

Shutter Speed

Fast Motion - High LED output Fast

Shutter Speed

Auto - allow the camera to determine

the LED luminance and Medium

Shutter Speed

Video Sound

(only affects video clips)

Off, On

Select “On” to record audio along

with the video when the camera is

set to video mode (saved file sizes

will be slightly larger).

Time Stamp

On, Off

Select “On” if you want the date &

time (that the photo or video was

recorded) imprinted on every photo

or video, select “Off” for no imprint.

Camera Mode

24 Hrs, Day, Night

Allows user to limit operation to only

day or night period if desired. An

ambient light level sensor determines

"Day" vs "Night" automatically.

Camera Name

Input

Allows user to set up the camera

name at 6 characters.

Format

No, Yes

Deletes (erases) all files stored on a

card to prepare it for reuse. Always

format a card that has been

previously used in other devices.

Caution! Make sure you have

downloaded and backed up any files

you want to preserve first! Press OK

to execute, press MENU (or select

NO then press OK) to exit without

formatting.

Version

n/a

Displays firmware version

19

Default Set

No, Yes

Select “Yes” and press OK to restore

all parameters to the original factory

default settings. If the camera is

behaving oddly and you think you

may have changed the setting for

something accidently (but aren’t

sure which one), this will reset all

parameters to their most commonly

used or “generic” settings.

FW Update

No, Yes

Allows users to update the FW when

the updated FW in the SD card.

20

MOUNTING AND POSITIONING THE

Prime Trail Camera

Mounting

After you’ve set up the camera’s parameters to your personal preferences at home or

in your truck, you’re ready to take it outside and slide the power switch to “ON”. When

setting up the Prime Trail Camera for scouting game or other outdoor applications, you

must be sure to mount it in place correctly and securely. We recommend mounting the

Prime Trail Camera on a sturdy tree with a diameter of about 6 in. (15cm). To get the

optimal picture quality, the tree should be about 16-17 ft. (5 meters) away from the

place to be monitored, with the camera placed at a height of 3.5-5 ft. (1~1.5 m). Also,

keep in mind that you will get the best results at night when the subject is within the

ideal flash range, no farther than 100’ (30m) and no closer than 10’ (3m) from the

camera.

There are two ways to mount the Prime Trail Camera: using the provided adjustable

web belt, or the tripod socket.

Using the adjustable web belt: Fig. 7 illustrates using the web belt on the Prime Trail

Camera. Push one end of the belt through the two brackets on the back of the Prime

Trail Camera. Thread the end of the strap through the buckle. Fasten the belt securely

around the tree trunk by pulling the end of the strap firmly so there is no slack left.

Fig. 7: Attaching the Belt

La pagina sta caricando ...

Bushnell Prime Trail 119932C 119932CB Manuale utente

Bushnell Prime Trail 119932C 119932CB Manuale utente

in altre lingue

Documenti correlati

Altri documenti