Sharp XE-A137-WH Istruzioni per l'uso

ELECTRONIC CASH REGISTER

FULL DETAILED INSTRUCTION MANUAL

SHARP ELECTRONICS (Europe) GmbH

Postbox 105504

20038 Hamburg, Germany

XE-A137/XE-A147

MODEL

XE-A137

XE-A147

SD card

ADDITIONAL INFORMATION:

We would like to point out that the time for the SD card storage depends on the size of the already used

memory on SD card.

Measurements have shown that backing up data is approximately 6 minutes, unless there are already up

to 3000 backups / directories on the SD card.

In order to obtain a realistic compromise between the required time and the to be stored data volume,

storage of data is limited to a maximum of 5000 entries.

But also under this condition a period over 13 years can be stored on SD card even so, daily data

storage is done.

Since SD cards have a specified lifetime we recommend to create regularly backups to ensure the

availability of critical data in the event of a faulty SD card.

CAUTION:

• The cash register should be securely fitted to the supporting platform to avoid instability when the drawer

is open.

• The socket-outlet shall be installed near the equipment and shall be easily accessible.

• For a complete electrical disconnection pull out the AC adapter.

1

INTRODUCTION

Thank you very much for your purchase of the SHARP Electronic Cash Register, Model XE-A137/XE-A147.

Please read this manual carefully before operating your machine in order to gain full understanding of functions

and features.

Please keep this manual for future reference. It will help you if you encounter any operational problems.

CAUTION!

Never install the batteries into the cash register before initializing it. Before you start operating the cash

register, you must first initialize it, then install three new alkaline batteries LR6 (“AA” size) on the register.

Otherwise, distorted memory contents and malfunction of the cash register will occur. For this procedure, please

refer to pages 7 to 8.

IMPORTANT

• Be very careful when removing and replacing the printer cover, as the cutter mounted on it is very

sharp.

• Install the cash register in a location not subject to direct sunlight, unusual temperature changes, high

humidity, splashing water or dust and sand.

Installation in such locations could cause damage to the cabinet, the electronic components and other precision

components.

• Never operate the register with wet hands.

The water could seep into the interior of the register and cause component failure.

• When cleaning your register, use a dry, soft cloth. Never use solvents, such as benzine and/or thinner.

The use of such chemicals will lead to discoloration or deterioration of the cabinet.

• The register plugs into any standard wall outlet (official (nominal) voltage).

Other electrical devices on the same electrical circuit could cause the register to malfunction.

• For protection against data loss, please install three alkaline batteries LR6 (“AA” size) after initializing

the cash register. When handling the batteries, please observe the following:

Incorrectly using batteries can cause them to burst or leak, possibly damaging the interior of the cash register.

• RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

• Be sure that the positive (+) and negative (–) poles of each battery are facing in the proper direction

for installation.

• Never mix batteries of different types.

• Never mix old batteries and new ones.

• Never leave dead batteries in the battery compartment.

• Remove the batteries if you do not plan to use the cash register for long periods.

• Should a battery leak, clean out the battery compartment immediately, taking care to avoid letting

the battery fluid come into direct contact with your skin.

• For battery disposal, follow the corresponding law in your country.

• For complete electrical disconnection, disconnect the AC adapter.

• Be sure to use the attached AC adapter. Otherwise, an electric shock or fire may be caused.

2

CONTENTS

INTRODUCTION ........................................................................................................................................... 1

IMPORTANT .................................................................................................................................................. 1

CONTENTS ................................................................................................................................................... 2

PARTS AND THEIR FUNCTIONS ................................................................................................................ 4

1 External View ........................................................................................................................................ 4

2 Printer ................................................................................................................................................... 4

3 Mode Switch and Mode key .................................................................................................................. 5

4 Keyboard .............................................................................................................................................. 5

5 Display .................................................................................................................................................. 6

6 Drawer Lock Key .................................................................................................................................. 6

PREPARING THE CASH REGISTER ........................................................................................................... 7

1 Initializing the Cash Register ................................................................................................................ 7

2 Installing Batteries ................................................................................................................................ 8

3 Installing a Paper Roll ........................................................................................................................... 9

HELP FUNCTION ........................................................................................................................................ 10

BASIC FUNCTION PROGRAMMING ......................................................................................................... 11

1 Abbreviations and Terminology ............................................................................................................11

2 Prior to Programming ...........................................................................................................................11

3 Language Selection ............................................................................................................................ 13

4 Date and Time Programming .............................................................................................................. 13

5 Tax Programming ................................................................................................................................ 14

6 Department Programming .................................................................................................................. 15

7 PLU (Price Look-Up) and Subdepartment Programming ................................................................... 18

8 Text Programming ............................................................................................................................... 20

BASIC SALES ENTRY (Example) ............................................................................................................. 22

1 Basic Sales Entry ................................................................................................................................ 22

2 PLU Sales Entry ................................................................................................................................. 23

CORRECTION ............................................................................................................................................. 24

1 Cancellation of the Numeric Entry ...................................................................................................... 24

2 Correction of the Last Entry (direct void) ............................................................................................ 24

3 Correction of the Next-to-last or Earlier Entry (indirect void) .............................................................. 25

4 Subtotal Void ....................................................................................................................................... 25

5 Correction after Finalizing a Transaction (Void mode) ........................................................................ 26

FULL SALES REPORT (X or Z REPORT) ................................................................................................. 27

OTHER BASIC SALES ENTRIES .............................................................................................................. 29

1 Additional Information for BASIC SALES ENTRY .............................................................................. 29

2 Error Warning...................................................................................................................................... 29

3 Starting Cash Memory (SCM) Entry ................................................................................................... 30

4 Item Entries ......................................................................................................................................... 31

5 Display of Subtotal .............................................................................................................................. 34

6 Finalization of Transaction .................................................................................................................. 35

7 Computation of VAT (Value Added Tax)/Tax ....................................................................................... 37

OPTIONAL FEATURES .............................................................................................................................. 39

1 Auxiliary Entries .................................................................................................................................. 39

2 Auxiliary Payment Treatment .............................................................................................................. 40

3 Special Printing Function .................................................................................................................... 42

PRIOR TO PROGRAMMING ...................................................................................................................... 43

AUXILIARY FUNCTION PROGRAMMING ................................................................................................. 45

1 Miscellaneous Key Programming ....................................................................................................... 45

2 Other Text Programming ..................................................................................................................... 49

3

ADVANCED FUNCTION PROGRAMMING ................................................................................................ 52

1 Register Number and Consecutive Number Programming ................................................................ 52

2 Various Function Selection Programming 1 ........................................................................................ 53

3 Various Function Selection Programming 2 ........................................................................................ 61

4 EURO Programming ........................................................................................................................... 63

5 Reading Stored Programs .................................................................................................................. 66

READING (X) AND RESETTING (Z) OF SALES TOTALS ......................................................................... 68

1 Summary of Reading (X) and Resetting (Z) Reports .......................................................................... 68

2 Daily Sales Totals ............................................................................................................................... 69

EJ REPORT READING AND RESETTING ................................................................................................. 70

EURO MIGRATION FUNCTION .................................................................................................................. 71

SD CARD FUNCTION ................................................................................................................................. 74

OPERATOR MAINTENANCE ..................................................................................................................... 76

1 In Case of Power Failure .................................................................................................................... 76

2 In Case of Printer Error ....................................................................................................................... 76

3 Cautions in Handling the Printer and Recording Paper ...................................................................... 76

4 Replacing the Batteries ....................................................................................................................... 77

5 Replacing the Paper Roll .................................................................................................................... 78

6 Removing a Paper Jam ...................................................................................................................... 79

7 Cleaning the Printer (Printer Head / Sensor / Roller) .......................................................................... 79

8 Removing the Drawer ......................................................................................................................... 80

9 Opening the Drawer by Hand ............................................................................................................. 80

BEFORE CALLING FOR SERVICE ............................................................................................................ 81

SPECIFICATIONS ....................................................................................................................................... 82

4

PARTS AND THEIR FUNCTIONS

1 External View

Plug the AC adapter connector into the AC

adapter jack, then plug the AC adapter into

the wall outlet.

Cheque slot

Printer cover

Display

Mode switch

RS-232 connector

(Only for the XE-A147)

Option battery shutter

(for the XE-A1BT)

(Only for the XE-A147)

SD card slot

(Important: For SD type card

SDHC 4GB to 32GB)

AC adapter jack

Drawer lock

Drawer

Keyboard

AC adapter

AC adapter connector

Reset switch (Only for the XE-A147)

Doing so may damage or delete the data.

DO NOT push the reset switch unless

instructed to do.

2 Printer

The printer is a receipt (one station) type thermal printer, and therefore it does

not require any type of ink ribbon or cartridge. The average life of the printer is

approximately 5 million lines.

When removing the printer cover, lift up its rear.

When installing the printer cover, hook it on the pawls on the cabinet and shut it.

Caution: The paper cutter is mounted on the printer cover. Be careful not

to cut yourself.

Print roller arm

Roller

Sensor

Printer head

NOTE

Donotattempttoremovethepaperwiththeprintrollerarminthehold

position.Thismayresultindamagetotheprinterandprinterhead.

5

3 Mode Switch and Mode key

Insert the mode key (the same key as drawer lock key) into the mode switch and move the key to get an

appropriate mode.

Mode key

: Turns the display off. No operations are possible.

REG: Permits transaction entry.

: Permits correction after finalizing a transaction.

X/Flash: Permits printing of sales reports and displaying the flash reports.

Z/PGM: Permits printing and resetting of sales reports and programming.

4 Keyboard

■

Keyboard layout

■

Key names

F

Paper feed key

p

PLU/Subdepartment

key

A

Total/Amount tender/

No sale key

@

Multiplication/

receipt switch key

! $

Department keys

v

Void key

l

Clear key

c

Credit key

E

Escape/Help key

0 :

1

9

Numeric keys

V

Foreign currency

exchange key

%

Percent key

s

Non-add code/Time

display/Subtotal key

t

Paid-out/Value added

tax key

H

Shift key

C

Cheque key

R

Receipt print/Received-

on-account key

6

5 Display

■

Operator display

Your cash register is equipped with a front LED (Light-Emitting Diode) display that affords easy visibility of 9

digits for the operator during transaction.

PLU/Subdepartment code

Department code Repeat

Receipt off (“.”)

Shift for the character entry (“_”)

DC for the character entry (“_”)

Amount: Appears in the far-right eight (max.) positions. When the amount is negative, the minus symbol “-”

appears before the amount.

Number of repeats for repetitive registrations:

The number of repeats is displayed, starting at “2” and incremental with each repeat. When you

have registered ten times, the display will show “0”. (2 → 3 ..... 9 → 0 → 1 → 2 ... )

Receipt function status:

The indicator “.” appears in the receipt off position when the receipt function is in the OFF status.

Time: Appears in the first to fifth positions (using 24-hour format) in the REG or

mode. Press the

s

key to display the time.

■

Machine state symbols

: Appears during programming.

: Appears with an error code when an error is detected. For the details of error codes, please refer to

“Error code table”.

:

Appears when the subtotal is displayed or when the amount tendered is smaller than the sales amount.

: Appears when the

V

key is pressed to calculate a subtotal in foreign currency.

: Appears when a transaction is finalized by pressing the

A

,

C

or

c

key.

: Appears when the change due amount is displayed.

: Appears in the far-left three positions at the timing of key entry when the electronic journal (EJ) memory

is full. (Depending on programming.)

: Appears when the voltage of the installed batteries is under the required level. You must replace with

new ones within two days. Refer to page 77 for details.

: Appears when the batteries are not installed, or the installed batteries are dead. You must replace with

new ones immediately. Refer to page 77 for details.

: May appear right below the seventh and eighth places at the timing of finalization of a transaction when

the electronic journal (EJ) memory is nearly full.

: Appears when programmed date (and time) for EURO modification operation has come.

: Appears when the paper is not set or out.

6 Drawer Lock Key

This key (the same key as mode key) locks and unlocks

the drawer. To lock it, turn 90 degrees counterclockwise.

To unlock it, turn 90 degrees clockwise.

7

PREPARING THE CASH REGISTER

Unpack the cash register and make sure all accessories are included. For details of accessories, please refer to

“SPECIFICATIONS” section.

For installing the cash register, find a stable surface near an AC outlet where the cash register will not subject to

water sources or direct sunlight.

For preparing the cash register, please follow the three steps shown below; “1 Initializing the Cash Register” on

this page, “2 Installing Batteries” on page 8, and “3 Installing a Paper Roll” on page 9.

1 Initializing the Cash Register

In order to operate the cash register properly, you must initialize it before operating for the first time. Follow this

procedure.

1. Insert the mode/drawer lock key into the mode switch and turn it to the REG position.

2. Insert the AC adapter into the AC outlet.

IMPORTANT: This operation must be performed without batteries installed.

3. The cash register has now been initialized. The register display will show “0.00”

with “

”.

NOTE

 IfthisdoesnothappenwheninsertingtheACadapter,thentheinitializationhasnotbeendone

successful.(Thiswilloccurwhenthevoltageishighbecauseyouoperatedthecashregisterbefore

startinginitialization.)WaitatleastoneminuteafterpullingouttheACadapterandreinserttheAC

adapterintotheACoutletonlyafterthiswaitingtimehaspassed.

8

2 Installing Batteries

Three new alkaline batteries LR6 (“AA”size) must be installed in the cash register to prevent the data and user-

programmed settings from being erased from the memory, when the AC adapter plug is accidentally

disconnected or in case of power failure. Once installed, the batteries will last approximately one year before

needing replacement. At this time, the “

” symbol will appear on the display to indicate the batteries are low

and must be replaced within two days. If the no battery symbol “

” appears, you must install the batteries

at once. Install three new alkaline batteries LR6 (“AA”size) according to the procedure shown below

with the AC adapter plug connected and set the mode switch to the REG position:

1. Push the printer cover forward and detach it.

Be careful with the paper cutter, so as not to cut yourself.

2. Open the battery compartment cover next to the paper roll cradle.

3. Install three new alkaline batteries LR6 (“AA”size) as per the diagram.

When the batteries are properly installed “ ” on the display will

disappear.

4. Close the battery compartment cover.

NOTE

 •Besuretoobserveprecautionsshownonpage1whenhandling

batteries.

 •

Ifyoupressakeybymistake,anerrorsymbol“ ”

maybedisplayed.Pressthe

l

keytoclearthesymbolafter

installingpaperrolls.

Caution: “ ” or “ ” can be displayed only when the cash register is being turned on. Please be

advised that when the cash register is being turned off for a long time, the data in memory

might be cleared without the warning symbols: “

” or “ ”.

9

3 Installing a Paper Roll

The register can print receipts. For the printer, you must install the paper roll provided with the register.

NOTE

 Installthepaperrollintheprinter.Becarefulthentosettherollandcutthepaperendcorrectly.

To the printer

Incorrect

To the printer

Correct

Correct Incorrect

(How to set the paper roll) (How to cut the paper end)

1. Remove the printer cover.

2. Lift up the print roller arm.

3. Set the paper correctly in the paper roll cradle as per the diagram.

NOTE

 Beforeplacinganewpaperrollinthepaperrollcradle,cutoff

thepasted(taped)partofthepaperandconfirmthatthecutend

ofthepaperisstraight.

4. Feed the end of the paper along with the paper positioning guides as

per the diagram.

5. While holding down the paper, slowly close the print roller arm, and

push down the arm until you hear a click locking the arm.

NOTE

 Iftheprintrollerarmisnotsecurelylocked,printingisnotdone

right.Ifthisproblemoccurs,openthearm,andclosethearm

asinstructedabove.

6. Cut off the excess paper and replace the printer cover.

7. Press the

F

key to make sure the paper end comes out of the

printer cover and clean paper appears.

NOTE

 Ifthepaperenddoesnotcomeout,opentheprintercover,

andpassthepaperendbetweenthepapercutterandthe

paperguideoftheprintercover,andreplacetheprinter

cover.

Paper positioning guides

Print roller arm

10

HELP FUNCTION

The help function allows you to print guidance messages for basic programming procedures of the cash register.

This function is available in any mode switch position other than “

”. For more details on each programming,

refer to “BASIC FUNCTION PROGRAMMING” on pages 11 to 21.

■

Printing the help menu

Press the

E

key to print the help menu. This menu provides a list of the programming procedures for which

you can print the guidance messages.

Key operation

Print

E

■

Printing guidance messages

By reference to the help menu above, press the corresponding numeric key and then the

E

key to print the

guidance message for each programming procedure.

Key operation

Print

4

E

Sample print of TIME SETTING

NOTE

 The

E

keyworksastheerrorescapefunctionduringatransaction.Finalizethetransactiontouse

thekeyasthehelpfunction.

11

BASIC FUNCTION PROGRAMMING

Before starting sales entries, you must first program necessary items so the cash register suits your sales

needs. In this manual, there are three sections, BASIC FUNCTION PROGRAMMING (pages 11-21) where

required items must be programmed, AUXILIARY FUNCTION PROGRAMMING (pages 45-51) for using all

available keyboard keys and ADVANCED FUNCTION PROGRAMMING (pages 52-67) where various optional

programming features are provided. Find the required functions and program them accordingly.

1 Abbreviations and Terminology

Dept.: Department; a category for merchandise classifications. Every sales item should belong to a

department.

PLU: Price Look Up; a category for merchandise classifications. PLUs are used to call up preset prices by a

code entry.

VAT: Value Added Tax

X report: Report to read sales data

Z report: Report to read and reset sales data

Receipt ON/OFF function: To print or not to print receipts in the REG mode.

2 Prior to Programming

■

Procedure for programming

1. Check to see whether a paper roll is present in the machine. If there is not enough paper on a roll, replace it

with a new one (refer to “Replacing the Paper Roll” in “OPERATOR MAINTENANCE” chapter for the

replacement).

2. Put the mode key in the mode switch and turn it to the Z/PGM position.

3. Program necessary items into the cash register.

Every time you program an item, the cash register will print the setting. Please refer to print samples in each

section.

4. If necessary, issue programming reports for your reference.

NOTE

 •Onthekeyoperationexampleshownintheprogrammingdetails,numberssuchas“221012”indicates

theparameterwhichmustbeenteredusingthecorrespondingnumerickeys.

 •Asterisksinthetablesshownintheprogrammingdetailsindicatedefaultsettings.

■

Description of special keys

0

,

1

to

9

Used for numerical number entry.

:

Used for character code entry.

l

Used for cancel entry.

s

Used for data decision entry.

A

Used for programming termination entry.

12

■

Guidance for text programming

The register allows you to program texts for department item names, PLU/subdepartment item names, logo

messages, foreign and domestic currency symbols, and function texts.

There are two ways for programming text; using character keys on the keyboard or entering character codes

with numeric keys on the keyboard.

NOTE

 Fordetailsofenteringcharactercodeswithnumerickeys,pleasereferto“PRIORTOPROGRAMMING”

sectiononpages43-44.

Character entry sequence

Capital letter selection

Assigned number (0 to 9) Character entry

Double-size character Small letter selection

W H

Assigned number and character table

0 0 0 Ä ä Ď ď Ò ò

1 v 1 1 Ö ö È è Ó ó

2 M m w 2 2 Ü ü É é Ô ô

3 d N n x 3 3 À à Ê ê Õ õ

4 e O o y 4 4 Á á Ë ë Š š

5 f P p

W

X

Y

Z z 5 5 Â â Ì ì Ť ť

6 g Q q 6 6

Ã

ã Í í Ù ù

7 h R r 7 7 Å å Î î Ú ú

8 i S s 8 8 Č č Ñ ñ Û û

9 9 9 Ç

A

B

a

b

K

L

k

l

U

V

u

C c

D

E

F

G

H

I

J j T t

% %

+ +

- -

! ! ç Ň ň Ž ž

H H H H H H H

H

Used for the small letter entry.

S

Used for a space entry.

B

Used to delete the last character or figure.

W

Used for the double-size character entry.

, , , , , , Used for character entry.

[ Example ] For entry character “MnH”

2 3 H 7

M n H

13

3 Language Selection

88

To set "0"

s @ A

*Language (0 - 4)

*Language: 0: English 1: German 2: French 3: Spanish 4: Swedish

By default, English is set.

Key operation example

Print

s

88

@

0

A

Caution: When you change the language, the texts such as logo messages and function texts, which you

programmed, will be reset to the default settings. The language selection must be made before

programming logo messages and function texts.

4 Date and Time Programming

■

Date

For setting the date, enter the date in 6 digits using the day-month-year (DD/MM/YY) format, then press the

s

key.

Date(DD/MM/YY)

s

Key operation example

Print

221012

(22 October, 2012)

s

Date

■

Time

For setting the time, enter the time in 4 digits using the 24-hour format. For example, when the time is set to

2:30 AM, enter 230; and when it is set to 2:30 PM, enter 1430.

Time(max. 4 digits in 24-hour format)

s

Key operation example

Print

1430

s

Time

14

5 Tax Programming

If you program the VAT/tax, the cash register can calculate the sales tax. In the VAT system, the tax is included

in the price you enter in the register, and the tax amount is calculated when tendered according to the VAT rate

programmed. In the tax system, the tax is calculated when tendered according to the tax rate programmed, and

added to the price. The cash register can provide totally 6 kinds of VAT/tax systems (automatic VAT1-4,

automatic tax 1-4, manual VAT 1-4, manual VAT 1, manual tax 1-4, and automatic VAT1 and automatic tax 2-4

systems) and 4 kinds of rates. By default, the cash register is pre-programmed as automatic VAT1-4 system.

When you program tax rate(s) and taxable status for each department (by default, VAT1/tax1 is set to taxable.),

tax will be automatically added to sales of items assigned to the department according to the programmed tax

status for the department and the corresponding tax rate(s).

For details of the tax systems, refer to “Computation of VAT (Value Added Tax)/tax” section. To change the tax

system, please refer to “Other programming” of “Various Function Selection Programming 1” section (Job code

69).

■

Tax rate programming

The percent rate specified here is used for tax calculation on taxable subtotals.

To program other kind of tax

To program “0.0000”

To delete a tax rate

*Tax rate: YYYYYYY

Tax rate=0.0000 to 100.0000

As s@ @

v

Tax number

(1 to 4)

9

*Tax rate

Key operation example

Print

s

9

@

2

@

0070000

s

A

15

6 Department Programming

Merchandise can be classified into a maximum of 8 departments. Items sold using the department keys can later

be printed on a report shown as the quantities sold and sales amounts classified by department. The data is

useful for making purchasing decisions and other store operations.

■

Department status

For dept. 5 through 8

To set all zeros

ABC

To program another department

Dept. key

A

@

H

Item: Selection: Entry:

A SICS / Normal SICS 1

Normal* 0

B Sign Negative department 1

Positive department* 0

C Type of unit price entry Open and preset 3

Preset only 2

Open only* 1

Inhibit department key 0

* Default settings

SICS (Single Item Cash Sale)

• If an entry of a department programmed for SICS is made first, the sale will be finalized as a cash sale as

soon as the department key is pressed. If the entry is made after entering a department not programmed for

SICS, it does not finalize and result in a normal sale.

Key operation example

Print

113

@

"

A

Sign

SICS / Normal

Type of unit price entry

16

■

Preset unit price

For dept. 5 through 8

To program zero

To program another department

Dept. key

A

H

Unit price (max. 8 digits)

Key operation example

Print

1000

!

A

Unit price

NOTE

 Ifadepartmentisnotprogrammedtoallowtheentryofpresetunitpricesinfunctionalprogramming,the

departmentisautomaticallychangedtoallowtheentryofpresetunitpricesbythisprogrammingentry.

■

VAT/tax status

For dept. 5 through 8

To program zero

VAT/tax status

(1 to 4)

20

Dept. key

To program another department

As @

H

VAT/tax status Selection: Entry:

VAT/tax 1* 1 e.g. for this number a VAT/tax rate of 7% is assigned

VAT/tax 2 2

VAT/tax 3 3

VAT/tax 4 4

Non VAT/tax 0

Key operation example

Print

s

20

@

2

!

A

VAT/tax status (VAT/tax 2)

17

■

HALO digits (entry digit limit)

Set the number of allowable digits for the maximum entry amount for each department. The limit is effective for

operations in the REG mode.

NOTE

 Toactivatethisfunction,theprogramming(jobcode62)“HALOfunction”mustbeset“Valid(1)”onpage

55.

For dept. 5 through 8

To program zero

28 HALO

(0 to 8)

Dept. key

To program another department

As @

H

Key operation example

Print

s

28

@

5

!

A

HALO (entry digit limit)

■

Department text (item label)

For dept. 5 through 8

To keep current setting

101 Character entry

(max. 12 characters)

Dept. key

To program another department

Ass @

H

Key operation example

Print

s

101

@

!

8 3 0 02

S

8

N A C K S

s

A

(Programming SNACKS for dept.1)

Text

programmed for

dept. 1

For details of the text entry (“SNACKS”), please refer to the “Guidance for text programming” on page 12.

18

7 PLU (Price Look-Up) and Subdepartment Programming

The PLU function allows speedy key entries whereby a price is automatically called up when a code is entered.

The subdepartment is a kind of “open PLU”, which requires you to enter a price after the PLU code is entered.

PLU/subdepartment setting for 1 through 200 codes are available.

■

Unit price and associated department assignment

To delete the PLU code

For dept. 5 through 8

To program zero

PLU code Unit price

(max. 8 digits)

To program or delete the following PLU code

To program or delete another PLU code

Associated

Dept. key

p

v

A

H

Key operation example

Print

1

p

125

!

A

PLU code

Unit price

Associated dept.

■

PLU/subdepartment selection

To program "0"

*A (0 or 1)PLU code

To program the following PLU code

To program another PLU code

Asp

*A: 0 for subdepartment or 1 for PLU

Key operation example

Print

1

p

0

s

A

PLU/subdept.

NOTE

 WhenyouprogramthelastPLUcode,theprogrammingsequencewillbecompletewithapressofthe

s

key.

La pagina sta caricando ...

Sharp XE-A137-WH Istruzioni per l'uso

Questo manuale è adatto anche per

Sharp XE-A137-WH Istruzioni per l'uso

in altre lingue

Altri documenti