Ubiquiti UAP-Outdoor 5G Manuale utente

Outdoor WiFi System

Models: UAP-Outdoor/UAP-Outdoor 5G

i

Table of ContentsUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

Table of Contents

Chapter 1: Product Overview .......................................1

Package Contents ................................................................1

System Requirements ............................................................1

Network Topology Requirements .................................................1

Hardware Overview ..............................................................2

Front .............................................................................2

Chapter 2: Installation ..............................................3

Hardware Installation .............................................................3

Antenna Installation ..............................................................4

Software Installation ..............................................................5

Chapter 3: Using the UniFi Controller Software ......................7

Interface Tabs ....................................................................7

Common Interface Options .......................................................7

Recent Events ....................................................................7

Settings ..........................................................................8

Admin ..........................................................................13

Chapter 4: Map Tab ................................................14

Adding Custom Maps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Adding a Google Map ...........................................................15

Placing Access Points on the Map ................................................17

Setting the Map Scale ...........................................................19

Chapter 5: Statistics Tab ...........................................21

Clients ..........................................................................21

Quick Look ......................................................................21

Current Usage - Top Access Points ...............................................22

Recent Activities .................................................................22

Chapter 6: Access Points Tab .......................................23

Chapter 7: Users Tab ...............................................25

Chapter 8: Guests Tab .............................................27

Chapter 9: Offline Clients Tab ......................................29

Chapter 10: Access Point Details ...................................30

Details .........................................................................30

Users ............................................................................32

Guests ..........................................................................32

Configuration ...................................................................33

ii

Table of ContentsUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

Chapter 11: User/Guest Details ....................................40

Details ..........................................................................40

Statistics ........................................................................40

History ..........................................................................41

Configuration ...................................................................41

Chapter 12: Hotspot Manager .....................................42

Appendix A: Portal Customization .................................44

Overview ........................................................................44

Enabling Portal Customization ...................................................44

Viewing the Default Portal .......................................................44

Setup ...........................................................................44

Appendix B: UniFi Discovery Utility ................................46

Overview ........................................................................46

Appendix C: Specifications ........................................48

Appendix D: Safety Notices ........................................50

Electrical Safety Information .....................................................50

Appendix E: Warranty .............................................51

General Warranty ................................................................51

Appendix F: Compliance Information ..............................52

Installer Compliance Responsibility ..............................................52

FCC .............................................................................52

Industry Canada .................................................................52

RF Exposure Warning ............................................................52

CE Marking ......................................................................52

RoHS/WEEE Compliance Statement ..............................................53

Appendix G: Declaration of Conformity ............................54

Appendix H: Contact Information ..................................55

Ubiquiti Networks Support ......................................................55

1

Chapter 1: Product OverviewUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

Chapter 1: Product Overview

Thank you for purchasing the Ubiquiti UniFi AP-Outdoor,

which is available in two models: UAP-Outdoor for 2.4 GHz

and UAP-Outdoor 5G for 5 GHz.

The UniFi AP-Outdoor works with the UniFi AP, AP-LR,

AP-Mini, and AP-Pro. For wireless uplinks, an Access Point

can only uplink to another Access Point using the same

radio band. For example, the UAP-Outdoor 5G can only

uplink to another UAP-Outdoor 5G or other AP using the

5GHz radio band.

The UniFi AP-Outdoor includes the UniFi Controller

software, which allows you to manage your wireless

network using your Web browser. This User Guide is for

use with the UniFi AP-Outdoor and version 2.0 or above

of the UniFi Controller software. Additional information is

available on our website at

http://wiki.ubnt.com/UniFi_FAQ

The UniFi AP-Outdoor also includes the necessary

hardware for mounting the unit on a wall or a ceiling. It

supports Passive PoE, which works with the included PoE

adapter. If you want to power the UniFi AP-Outdoor from

an 802.3af compliant switch, Ubiquiti Networks offers the

optional Instant 802.3af Adapter to instantly transform

any PoE device into a fully 48V 802.3af compliant product.

Product details are available on our website at

http://ubnt.com/8023af

Package Contents

UniFi AP-Outdoor Wall-Mount Bracket Metal Strap

Outdoor WiFi System

Quick Start Guide UniFi Controller

CD with User Guide

Antennas

24V PoE Adapter Power Cord Screws (Qty. 3) Anchors

System Requirements

• Microsoft Windows XP, Windows Vista, Windows 7, or

Mac OS X

• Java Runtime Environment 1.6 (or above)

• Web Browser: Mozilla Firefox, Google Chrome, or

Microsoft Internet Explorer 8 (or above)

Network Topology Requirements

• A DHCP-enabled network (for the wired Access Point to

obtain an IP address as well as for the wireless Access

Points after the deployment)

• A management station computer running the UniFi

Controller software, located either onsite and connected

to the same Layer-2 network, or off-site in a cloud or

NOC

or

On-Site

Management Station

UAP-Outdoor

Wireless

Uplinked

1

UAP-Outdoor

UAP-Outdoor 5G

Router

Off-Site

Cloud/NOC

2

Sample Network Topology

¹ Please refer to “Wireless Uplinks” on page 36 for

setting up wireless-linked APs.

² All UniFi APs support off-site management controllers.

2

Chapter 1: Product OverviewUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

Hardware Overview

Connect to

Antennas

Removable Cover

Secondary

Ethernet Port

Main

Ethernet Port

Note: The Secondary Ethernet Port can be used as

as an uplink for other devices once they have been

adopted.

Front

LED Indicates the status of the device. See

the table below for details.

LED Color Status

Flashing Amber Initializing after startup.

Steady Amber Factory default, waiting to be integrated.

Alternating

Amber/Green

Device is busy; do not touch or unplug it.

This usually indicates a process such as a

firmware upgrade is taking place.

Quickly Flashing

Green

This is used to locate an AP.

When you click Locate in the UniFi

Controller software, the AP will flash. It will

also display the location of the AP on the

map.

Steady Green

Indicates the device has been successfully

integrated into a network and is working

properly.

Steady Green

with occasional

flashing

Indicates the device is in an isolated state

(all WLANs are brought down until an

uplink is found).

3

Chapter 2: InstallationUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

Chapter 2: Installation

Hardware Installation

The UniFi AP-Outdoor is powered by the included PoE

(Power over Ethernet) Adapter. To install the AP, perform

the following steps:

1. Connect an Ethernet cable to the primary Ethernet port

on the UniFi AP-Outdoor, and connect the other end of

the Ethernet cable to the Ethernet port labeled POE on

the PoE Adapter.

2. Connect an Ethernet cable from your LAN to the

Ethernet port labeled LAN on the PoE Adapter.

3. Connect the power cord to the power port on the PoE

Adapter. Connect the other end to of the power cord to

a power outlet.

Below is an overview of the Power over Ethernet

connections.

Power Connection Diagram

Note: The UniFi AP-Outdoor supports Passive PoE,

which works with the included PoE adapter. If

you want to power the UniFi AP-Outdoor from an

802.3af compliant switch, Ubiquiti Networks offers

the optional Instant 802.3af Adapter to instantly

transform any PoE device into a fully 48V, 802.3af

compliant product. Product details are available on

our website at http://ubnt.com/8023af

Mounting the UniFi AP-Outdoor

The UniFi AP-Outdoor can be mounted on a wall or pole.

Wall Mount

To mount the UniFi AP-Outdoor on a wall, use the

included Wall Mount Bracket, screws, and anchors.

1. Align the Wall Mount Bracket to the desired position on

a wall.

2. Use a pencil to mark the holes on the wall.

3. Use a 6 mm drill bit to drill the holes in the wall.

4. Insert the 3 screw anchors into the wall.

5. Secure the Wall Mount Bracket to the wall by inserting

the self tapping screws into the anchors.

4

Chapter 2: InstallationUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

6. Align the notches on the UniFi AP-Outdoor with the

notches on the Wall Mount Bracket, and slide the UniFi

AP-Outdoor down until it locks into place.

Pole Mount

To mount the UniFi AP-Outdoor on a pole, use the

included Metal Strap.

1. Open the Metal Strap by turning the locking

mechanism counter-clockwise. You can loosen it by

hand or use a flathead screwdriver.

2. Straighten out the end of the Metal Strap and slide it

through the back of the UniFi AP-Outdoor.

3. Wrap the Metal Strap around the pole and use a

flathead screwdriver to tighten the locking mechanism

by turning it clockwise.

Antenna Installation

Connect each antenna to an antenna connector by

rotating it clockwise.

5

Chapter 2: InstallationUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

Software Installation

Insert the UniFi Controller software CD into your CD-ROM

drive and follow the instructions for your specific

computer type.

Mac Users

1. Click the Install icon.

2. Click Continue and follow the on-screen instructions to

install the software.

3. Go to Go > Applications and double-click the UniFi

icon.

Proceed to”Configuring the UniFi Controller Software”

on page 6.

PC Users

1. Launch UniFi-installer.exe.

2. Click Install.

3. If your computer doesn’t have Java 1.6 or above

installed, you will be prompted to install it. Click Install

to continue.

4. Click Next.

5. Ensure that the Start UniFi Controller after installation

option is checked and click Finish.

Note: The UniFi Controller software can also be

launched from Start > All Programs.

6

Chapter 2: InstallationUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

Configuring the UniFi Controller Software

1. The UniFi Controller software startup will begin. Click

Launch a Browser to Manage Wireless Network.

2. Select your language and country. Alternatively, you

click restore from a previous backup to use a file that

contains your backup settings. Click Next.

Note: U.S. product versions are locked to the U.S.

Country Code to ensure compliance with FCC

regulations.

3. Select the devices that you want to configure and click

Next.

4. The UniFi Installation Wizard will create a secure

primary wireless network for your devices. Perform the

following steps:

a. Enter the wireless network name (SSID) in the Secure

SSID field.

b. Enter a passphrase to be used for your primary

network in the Security Key field.

c. To enable guest access, select Enable Guest Access

and enter a guest network name in the Guest SSID

field.

d. Click Next.

5. Enter an admin name in the Admin Name field and

password in the Password field to use when accessing

the management interface. Confirm your password in

the Confirm field. Click Next.

6. Review your settings. Click Back to make changes or

Finish to save your settings. Once finished you will be

redirected to the management interface via your Web

browser.

Congratulations, your wireless network is now configured.

A login screen will appear for the UniFi Controller

management interface. Enter the admin name and

password that you created and click Login.

Proceed to the next chapter for information on using the

UniFi Controller software.

7

Chapter 3: Using the UniFi Controller SoftwareUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

Chapter 3: Using the UniFi

Controller Software

The UniFi Controller software that comes with your

UniFi AP-Outdoor has a browser-based interface for easy

configuration and management.

To access the interface, perform the following steps:

1. Launch the UniFi Controller application if hasn’t already

been started.

•Mac users: Go > Applications > UniFi

•Windows users: Start > All Programs > Ubiquiti

UniFi.

2. The UniFi login screen will appear. Enter the admin

name and password in the appropriate fields and click

Login.

Interface Tabs

The UniFi software consists of six primary tabs. This User

Guide covers each tab with a chapter. For details, on a

specific tab, refer to the appropriate chapter.

• “Map Tab” on page 14

• “Statistics Tab” on page 21

• “Access Points Tab” on page 23

• “Users Tab” on page 25

• “Guests Tab” on page 27

• “Offline Clients Tab” on page 29

Common Interface Options

The common interface options are accessible from all tabs

in the UniFi interface.

Access Points

• connected Drop-down clickable list of all of the Access

Points that are online.

• disconnected Displays a list of Access Points that were

previously online but are no longer accessible.

• pending Drop-down clickable list of all of the Access

Points that are not yet managed but are available for

management.

Stations

• users Displays the total number of users connected to

the primary network.

• guests Displays the total number of users connected to

the guest network.

Recent Events

Displays a list of recent events including the date and time

the event occurred and the details of the event. The User

and Access Point names are clickable links.

Event Slider Move the slider right and left to navigate

between pages of events.

Search Allows you to enter text you want to search for.

Simply begin typing; there is no need to press Enter.

Clicking on an Event Device Link

The event messages have clickable links [in brackets

underlined in gray text] for AP (see “Access Point Details”

on page 30), User, and Guest (see “User/Guest Details”

on page 40). Details vary based on the selection.

8

Chapter 3: Using the UniFi Controller SoftwareUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

Alerts

Important events are displayed in the alerts window. The

date and time of the event and the message are displayed.

Search Allows you to enter text you want to search for.

Simply begin typing; there is no need to press Enter.

Show Archived Show all of the alert messages that have

been archived.

Archive All Archive all of the alert messages displayed on

the screen.

Adopt Click to adopt an Access Point that is waiting for

adoption.

Archive Archive the selected alert message.

Settings

System System related settings.

Guest Control Guest portal and policies.

Wireless Networks Wireless networks.

Blocked Devices List of blocked wireless

devices.

>_

Admin Settings Admin username, password,

and preferences.

User Groups User Group settings.

Settings > System

System Configuration

System Name Editable field with the system name.

Country Select your country from the drop-down list.

Services

Automatic Upgrade When enabled, this option will

automatically upgrade your firmware when an update is

available.

LED When enabled, the LED on the Access Point will light

up. When disabled, the LED will turn off.

Background Scanning When this option is enabled, all

managed Access Points will scan in the background for

“Rogue Access Points” – third-party or UniFi Access Points

that are being managed by another instance of the UniFi

Controller software. This option is disabled by default.

• Scan Now When clicked, all managed Access Points

will scan across all maps for two to three seconds. New

Access Points in their default state will appear under

Access Points > Pending.

Load Balancing Sets a desired number of clients per AP.

While an AP will allow more clients to connect, it will start

to look at those with lower signals and disconnect them.

Network Discovery When enabled, this option allows

UniFi to be discoverable via UPnP. This option is disabled

by default.

Uplink Connectivity Monitor It monitors the uplinks of

the managed Access Points, either wired or wireless, by

checking to see if the gateway/custom IP can be reached.

The monitor and wireless uplink capability are enabled by

default.

• Use default gateway Use default gateway is selected by

default; all managed Access Points will use the gateway

of the Access Point that is providing IP information,

either by DHCP or Static designation.

• Use custom IP Select Use custom IP to specify an

IP address; all managed Access Points will use the IP

address you enter in the Uplink IP address field.

9

Chapter 3: Using the UniFi Controller SoftwareUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

Remote Logging Enable to define a remote syslog server.

Enter the IP address and port of the syslog server.

Click Apply to save any changes that you have made.

Mail Server

When enabled, UniFi will send email alerts when triggered

(Pending Access Points and Disconnected Access Points)

to the administrator email address specified under

Settings>Admin Settings > Admin Preferences > Email Alert.

SMTP Server Enable by selecting the checkbox

and entering the outgoing (SMTP) mail server name.

Optionally, you may enable Secure Sockets Layer (SSL) to

provide communication security over the Internet. The

port number will automatically change to 465.

Enable authentication Enable by selecting the checkbox

and entering the username and password required by the

mail server.

Test SMTP Server Enter an email address and click Send

to test the mail server setup.

Apply Click Apply to save changes.

Settings > Guest Control

Guest Policies

Guest Portal This option is disabled by default. When

disabled, guests can access the Internet without entering

a password or accepting Terms of Use. When this option is

enabled, you can control the Guest Portal.

Authentication When the Guest Portal is enabled, the

authentication options will appear. There are four different

authentication methods available:

• No authentication When this option is selected, guests

are not required to log in, but must accept the Terms

of Use. When you select No authentication, you must

select Guest Policy under Settings > Wireless Networks >

SSID > Edit > Wireless Configurations in order to enforce

selection of the Terms of Use by the guest.

• Simple Password When this option is selected, guests

are required to enter the simple password and accept

the Terms of Use. When you select Simple Password,

you must select Guest Policy under Settings > Wireless

Networks > SSID > Edit > Wireless Configurations in order

to enforce entry of the password and selection of the

Terms of Use by the guest.

• Hotspot When selected, enables Hotspot functionality

including the ability to customize portal login pages and

bill customers using major credit cards or via PayPal™.

When you select Hotspot, you must select:

• Voucher or Payment in the Hotspotsectionasa

method of Hotspot authorization

• Guest Policy to enforce entry of voucher, payment,

and Terms of Use by the guest (Go to Settings >

Wireless Networks > Name_of_wireless_network > Edit >

Wireless Configurations.)

• External Portal Server If using an external server

to host a custom guest portal, enter the IP address in

the Custom Portal > IP Address box using the following

format: 192.168.0.0.

• Guest Password (Option only available when using

Simple Password authentication) Enter a password that

guests must enter before accepting the Terms of Use

and connecting to the Internet.

10

Chapter 3: Using the UniFi Controller SoftwareUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

• Expiration (Option only available when using No

authentication or Simple Password authentication)

Allows the specification of guest login expiration after

a designated period of time. Options include: 8 hours,

24 hours, 2 days, 3 days, 4 days, 7 days, and User-defined.

User-defined can be designated in minutes, hours, and

days.

• Custom Portal (Option only available when using

External Portal Server authentication) Enter the IP

address using the following format: 192.168.0.0.

• Landing Page (Option only available when using

No authentication, Simple Password, or Hotspot

authentication) The landing page is the page where

guests are redirected after accepting the Terms of Use.

There are two options available:

- Redirect to the original URL When this option

is selected, guests are directed to the URL they

requested after accepting the Terms of Use.

- Promotional URL When this option is selected,

guests are redirected to the URL that you specify here

after accepting the Terms of Use. Specify the URL with

http:// in front of the Web address.

Example: http://www.ubnt.com

• Portal Customization (Option only available when

using No authentication, Simple Password, or Hotspot

authentication) When enabled, allows customized portal

pages to appear in place of default login pages. See

“Portal Customization” on page 44 for details on

setting up custom portal pages.

• Portal URL Hostname Allows the designation of a

hostname for the portal URL in place of the default

IP address. Paired with a SSL certificate, ensures site

certificates are displayed as trusted in the guest browser.

Example: www.ubnt.com

Hotspot

The Hotspot options are only available when Hotspot

authentication is selected.

• Voucher When selected, vouchers (including

distributable code, duration values, and use restrictions)

can be created using Hotspot Manager (see “Hotspot

Manager” on page 42).

• Payment When enabled, allows payment-based

authentication to be set up with your PayPal Website

Payments Pro account. Payments and Transactions can

be managed using Hotspot Manager (see “Hotspot

Manager” on page 42).

• PayPal PayPal account details are entered here:

- Username Enter the corresponding Username.

- Password Enter the corresponding Password.

- Signature Enter the corresponding Signature for the

PayPal account to be used for receiving payments.

- Use Paypal Sandbox For PayPal testing purposes,

enable this option and click Apply Sandbox

Account to set up/access your PayPal Sandbox Test

Environment.

• Hotspot Operator Click Go to Hotspot Manager

to manage Wireless Guests, Payments/Transactions,

Vouchers, and Operator Accounts. See “Hotspot

Manager” on page 42.

• Apply Click Apply to save changes.

When logging in with No authentication, guests will be

required to accept the Terms of Use before gaining access

to the Internet.

When logging in with Simple Password authentication,

guests will be required to enter the Guest Password and

accept the Terms of Use before gaining access to the

Internet.

When logging in with Voucher-based Hotspot

authentication, guests will be required to enter the

voucher number and accept the Terms of Use before

gaining access to the Internet.

11

Chapter 3: Using the UniFi Controller SoftwareUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

When logging in with Payment-based Hotspot

authentication, guests will be required to select the

package type, click the payment choice, and accept the

Terms of Use before gaining access to the Internet.

Access Control

Restricted Subnets Enter any subnets that you don’t

want guests to be able to access.

Apply Click Apply to save changes.

Settings > Admin Settings

Admin Name Displays the current admin name used to

log in. To change the admin name, simply enter a new

name and click Apply.

Password A new password can be entered in this field.

Ensure that you enter the password again in the Confirm

field and then click Apply to save your new password.

Confirm Used to confirm your new password.

Language Selects the language for use in the interface.

Email Alert Select to enable email alerts and enter the

administrator email address in the Send alert to email

box. See “Mail Server” on page 9 for information on

setting up the outgoing (SMTP) mail server.

Apply Click Apply to save changes.

Settings > Wireless Networks

Wireless Configurations

Name Displays the wireless network name (SSID).

Security Displays the type of security being used on your

wireless network.

Guest Network Indicates whether the network is a guest

network.

Actions Select an action button to perform the desired

action:

• Edit Select to make changes to the wireless network

settings.

• Delete Select to delete the wireless network.

Wireless Configuration

• Name/SSID Allows you to edit the wireless network

name (SSID).

• Security Selects the type of security to use on your

wireless network.

- Open This option is typically only used on the Guest

network. When enabled, wireless network access is

open to anyone without needing a password.

- WEP WEP (Wired Equivalent Privacy) is the oldest and

least secure security algorithm. WPA security methods

should be used when possible.

• WEP Key Enter a WEP encryption key in

hexadecimal format. You can enter a 64-bit or

128-bit key:

Type Hex

64-bit 10 Hexadecimal Characters

(0-9, A-F, or a-f)

Example: 00112233AA

Note: You can use 5 printable characters,

which will be translated to the

corresponding HEX code.

128-bit 26 Hexadecimal Characters

(0-9, A-F, or a-f)

Example:

00112233445566778899AABBCC

Note: You can use 13 printable

characters, which will be translated to the

corresponding HEX code.

• Key Index Specifies the Index of the WEP Key used.

Four different WEP keys can be configured at the

same time, but only one is used. The effective key is

set by choosing 1, 2, 3 or 4.

12

Chapter 3: Using the UniFi Controller SoftwareUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

- WPA-Personal WPA™ or Wi-Fi Protected Access was

developed as an encryption method stronger than

WEP. WPA-Personal requires a passphrase to connect

to the wireless network.

• Security Key Enter the passphrase that users will

use to connect to the wireless network.

- WPA-Enterprise WPA Enterprise uses a RADIUS

server to authenticate users on the wireless network.

• IP Address This is where the IP address of the

RADIUS server is specified.

• Port The port number is entered here. By default it

is 1812.

• Password The password used to authenticate on

the RADIUS server is entered here.

• Guest Policy Select this option to enable guest access

policies on this wireless network.

Advanced

• VLAN To use a VLAN, select Use VLAN ID and enter the

port number.

• Hide SSID Select this option if you don’t want the SSID

to be broadcast.

• WPA Defines supported WPA and encryption methods.

• User Group Allows assignment of wireless users to a

specific user group.

Click Apply to save any changes that you have made.

Click Cancel to discard changes.

Settings > Blocked Devices

Displays the list of blocked wireless devices.

Unblock Click to unblock a wireless device. See “User/

Guest Details” on page 40 for information on blocking

wireless devices.

Settings > User Groups

Create Click to create a new user group.

• Name Enter a descriptive user group name.

• Bandwidth Limit (Download) When selected, allows

the designation of a download bandwidth limit in Kbps.

• Bandwidth Limit (Upload) When selected, allows the

designation of an upload bandwidth limit in Kbps.

- Create Click to create a user group.

- Cancel Click to cancel user group creation.

Edit Click to change the name or bandwidth settings of

the user group.

Delete Click to delete the user group.

See “Configuration” on page 41 for information on the

application of User Groups to Users/Guests.

13

Chapter 3: Using the UniFi Controller SoftwareUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

Admin

The Admin tab displays server version information,

allows system backups to be created and downloaded,

allows system restoration from backup files, and allows

configuration information to be downloaded to assist in

support issues.

Server Information

Version The software version is displayed here. If there

is an update, UniFi will automatically download it and

display it here.

Backup

Download Backup Settings Click to download a file that

contains all of your settings so you can restore them later

if you choose.

Restore

Choose File Select this option to restore settings from a

backup file that you’ve already downloaded.

Support Info

Download Support Info Select this option to download

a file to your computer with information about your

configuration that can be emailed to our support team.

14

Chapter 4: Map TabUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

Chapter 4: Map Tab

The UniFi Controller software allows you to upload custom

map images of your location(s) or use Google Maps

™

for a

visual representation of your wireless network. When you

initially launch the UniFi Controller application, a default

map is displayed.

Adding Custom Maps

To add a custom map, you must first create the image

using an illustration, image editing, or blueprint

application that exports .jpg, .gif, or .png file formats.

Once you’ve created the map, you can upload it to the

UniFi Controller software by performing the following

steps:

1. Click Configure Maps.

Configure Maps button

15

Chapter 4: Map TabUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

2. Click Add a Map.

Add a Map

3. Enter a map name in the Description field and click

Upload my own. Click the Browse button to locate the

file to use as a map (valid file formats are .jpg, .gif, and

.png). Click Continue.

4. Click Close.

Adding a Google Map

To add a Google Map to the UniFi Controller software Map

view:

1. Click Configure Maps.

Configure Maps button

2. Click Add a Map.

Add a Map

16

Chapter 4: Map TabUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

3. Enter a map name in the Description field and click Use

Google Maps. Click Continue.

4. In order to use a Google Map, you must register with

Google for a Google Maps API key. To do so, click

Specify API Key.

5. Click or copy and paste the Web link from the window

into a new Web browser window. Do not close the

UniFi window.

http://code.google.com/apis/maps/signup.html

6. You need to be signed in with a Google account to

obtain a Google Maps API key.

7. Review the terms and conditions and click the

checkbox next to I have read and agree with the

terms and conditions.

8. Navigate back to the UniFi window and copy the

address that UniFi displays in the address bar.

Note: You only need to copy until the end of the

address; do not include the port information.

In the example below, the full address is

https://192.168.25.191:8443/manage#. You only

need to copy up to https://192.168.25.191. Do not

include the colon or anything beyond it.

9. Navigate back to the Google Maps API Family window

and paste the address into the My web site URL: box.

10. Click the Generate API Key button.

11. A new window will open, displaying your key. Highlight

and copy the Google Maps API key.

Google Maps API Key

12. Navigate back to the UniFi window and paste the API

Key into the API Key field. Click continue.

17

Chapter 4: Map TabUniFi

™

AP-Outdoor User Guide

Ubiquiti Networks, Inc.

13. The default Google Map location will appear. Click the

Set Location button in the lower left.

Set Location button

14. Select Specify Address to enter an address. Type in the

address and then click Go. You also have the Specify

Coordinates option to enter the latitude and longitude

of a specific location.

15. The specified location should appear. Click Save.

16. Click Close.

17. You can adjust the zoom using the slider on the right.

Placing Access Points on the Map

1. Drag the Access Point icon(s) from the Unplaced APs list

on the left to the appropriate location(s) on the map.

The access point will appear in the area that you placed it.

La pagina sta caricando ...

Ubiquiti UAP-Outdoor 5G Manuale utente

Questo manuale è adatto anche per

Ubiquiti UAP-Outdoor 5G Manuale utente

in altre lingue

Documenti correlati

Altri documenti