Whirlpool K6C10(W)/R Guida utente

Categoria
Forni
Tipo
Guida utente

Questo manuale è adatto anche per

Cucina
Installazione e uso
Cooker
Installation and use
Êóõoííaÿ ïëèòà
Óñòàíîâêà è ïîëüçîâàíèå
K6 C11/R
K6 C10/R
Cucina con forno elettrico e piano vetroceramica
Istruzioni per l'installazione e l'uso 3
Cooker with electric oven and ceramic hob
Instructions for installation and use 12
Ïëèòà ñ ýëåêòðè÷åñêîé äóõîâêîé è
ñòåêëîêåðàìè÷åñêîé ïîâåðõíîñòüþ
Èíñòðóêöèè ïî èñïîëüçîâàíèþ è îáñëóæèâàíèþ 20
3
Avvertenze
1 Questo apparecchio è stato concepito per un uso di tipo
non professionale all'interno di abitazione.
2 Prima di utilizzare l'apparecchio leggere attentamente le av-
vertenze contenute nel presente libretto in quanto fornisco-
no importanti indicazioni riguardanti la sicurezza di instal-
lazione, d'uso e di manutenzione Tenere questo manuale
come guida di riferimento.
3 Rimuovere l'imballo e controllare che l'apparecchio non sia stato
danneggiato dalle operazioni di trasporto. Nel caso in cui si abbia-
no dei dubbi, è meglio non utilizzarlo e rivolgersi ad un tecnico
qualificato. Per ragioni di sicurezza, tenere i materiali utilizzati per
l'imballo (buste di plastica, polistirolo espanso, bullette, ecc.) lon-
tano dalla portata dei bambini.
4 L'apparecchio deve essere installato da un tecnico qualificato se-
condo le istruzioni fornite dal fabbricante. Il fabbricante non si as-
sume alcuna responsabilità per lesioni o danni a persone, animali
o cose causati dalla mancata osservanza di queste istruzioni.
5 La sicurezza elettrica di questo apparecchio è garantita soltanto a
patto che esso sia stato collegato in maniera corretta ad un impian-
to di messa a terra che sia funzionante e conforme alle norme vi-
genti sulla sicurezza elettrica. Controllare che questo requisito di
sicurezza fondamentale sia sempre rispettato. Nel caso si abbiano
dei dubbi, farlo controllare da un tecnico qualificato. Il fabbricante
non si assume alcuna responsabilità per danni causati da un colle-
gamento a terra difettoso.
6 Prima di collegare l'apparecchio, controllare che le specifiche del-
la targhetta dei dati di funzionamento corrispondano a quelle del-
la vostra alimentazione.
7 Controllare che l'alimentazione e le prese siano sufficienti per il carico
complessivo richiesto dall'apparecchio, così come viene specificato
nella targhetta dei dati di funzionamento. Nel caso in cui si abbiano
dei dubbi, rivolgersi ad un tecnico qualificato.
8 Per l'installazione è necessario utilizzare un interruttore multiplo
con uno spazio tra i contatti pari ad almeno 3 mm.
9 In caso di incompatibilità tra la presa e la spina dell'apparecchio
fare sostituire la presa con altra di tipo adatto da personale pro-
fessionalmente qualificato. Quest'ultimo, in particolare, dovrà an-
che accertare che la sezione dei cavi della presa sia idonea alla
potenza assorbita dall'apparecchio. In generale è sconsigliabile
l'uso di adattatori, prese multiple e/o prolunghe. Se non è possibi-
le fare a meno di utilizzarli, ricordarsi sempre di utilizzare soltanto
prolunghe e adattatori singoli o multipli che siano conformi alle
norme vigenti in materia di sicurezza. e non superare mai la capa-
cità massima indicata sulla prolunga o sull'adattatore singolo e la
potenza massima indicata sull'adattatore multiplo.
10 Non lasciare l'apparecchio inutilmente inserito. Spegnere l'inter-
ruttore generale dell'apparecchio quando lo stesso non è utilizza-
to, e chiudere il rubinetto del gas.
11 Le aperture e le fessure impiegate per la ventilazione e la
dispersione del calore non devono in nessun caso essere
chiuse o tappate.
12 Il cavo di alimentazione di questo apparecchio non deve essere
sostituito dall'utente. In caso di danneggiamento del cavo, o per la
sua sostituzione, rivolgersi esclusivamente ad un centro di assi-
stenza tecnica autorizzato dal costruttore.
13 Questo apparecchio dovrà essere destinato solo all'uso per il quale
è stato espressamente concepito.
Ogni altro uso (ad esempio: riscaldamento di ambienti) è da con-
siderarsi improprio e quindi pericoloso.
Il costruttore non può essere considerato responsabile per eventuali
danni derivanti da usi impropri, erronei ed irragionevoli.
14 L'uso di un qualsiasi apparecchio elettrico comporta l'osservanza
di alcune regole fondamentali. In particolare:
· non toccare l'apparecchio con mani o piedi bagnati o umidi.
· non usare l'apparecchio a piedi nudi
· non usare, se non con particolare cautela, prolunghe
· non tirare il cavo di alimentazione, o l'apparecchio stesso, per
staccare la spina dalla presa di corrente.
· non lasciare esposto l'apparecchio ad agenti atmosferici (piog-
gia, sole, ecc.)
· non permettere che l'apparecchio sia usato dai bambini o da
incapaci, senza sorveglianza
15 Prima di effettuare qualsiasi operazione di pulizia o di manuten-
zione, disinserire l'apparecchio dalla rete di alimentazione elettri-
ca, o staccando la spina, o spegnendo l'interruttore dell'impianto.
16 Nel caso in cui si rompa la superficie del vetro, scollegare imme-
diatamente l'apparecchio. Per l'eventuale riparazione rivolgersi
solamente ad un centro di assistenza tecnica autorizzato e richie-
dere l'utilizzo di ricambi originali. Il mancato rispetto di quanto so-
pra può compromettere la sicurezza dell'apparecchio.
17 Allorché si decida di non utilizzare più l'apparecchio, si raccoman-
da di renderlo inoperante tagliandone il cavo di alimentazione,
dopo aver staccato la spina dalla presa di corrente. Si raccoman-
da inoltre di rendere innocue quelle parti dell'apparecchio suscet-
tibili di costituire un pericolo, specialmente per i bambini che po-
trebbero servirsi dell'apparecchio fuori uso per i propri giochi.
18 Il piano di cottura in porcellana dura resiste alle fluttuazioni di tem-
peratura e agli urti. Ricordarsi, tuttavia, che lame o utensili da cuci-
na affilati possono rompere la superficie del piano di cottura. Se ciò
accade, togliere immediatamente la spina della cucina dalla rete e
rivolgersi al servizio di assistenza locale.
19 Ricordarsi che la superficie di cottura resta calda per almeno mez-
z'ora dopo essere stata spenta. Non riporre recipienti o altri og-
getti sulla superficie calda.
20 Evitare di riporre oggetti sulla superficie di vetro del piano cottura.
21 Non accendere le superfici di cottura, se vi sono lamine di allumi-
nio o di plastica sul piano di cottura.
22 Tenersi lontano dalle superfici calde.
23 Quando si utilizzano piccoli elettrodomestici accanto al piano di
cottura, controllare che il cavo di alimentazione non si trovi sulle
superfici calde.
24 Tenere i manici delle pentole rivolti verso l'interno in modo da evi-
tare di urtarle accidentalmente e farle cadere dal piano di cottura.
25 Quando si accende la superficie di cottura, riporre sempre una
pentola sulla superficie immediatamente per evitare che si surri-
scaldi velocemente e rischi di danneggiare gli elementi riscaldan-
ti.
26 Istruzioni preliminari. Il sigillante del vetro che viene utilizzato
potrebbe lasciare tracce di grasso sul vetro stesso. Ricordarsi di
rimuoverle con una normale sostanza detergente non abrasiva
prima di mettere in funzione l'apparecchio. Durante le prime ore di
funzionamento è possibile che venga avvertito un odore di gom-
ma, che comunque scomparirà presto.
27 Quando il grill o il forno sono in funzione, alcune parti della
porta possono diventare molto calde. Tenere i bambini a di-
stanza.
28 controllare sempre che le manopole siano nella posizione "o"/"o"
quando l'apparecchio non è utilizzato;
29 Se la cucina viene posta su di un piedistallo, prendere adeguati
accorgimenti affinchè l'apparecchio non scivoli dal piedistallo
stesso.
Per garantire l’efficienza e la sicurezza di questo elettrodomestico:
rivolgetevi esclusivamente a centri di assistenza tecnica autorizzati
richiedete sempre l’utilizzo di parti di ricambio originali
4
Installazione
Le istruzioni che seguono sono rivolte all’installatore qua-
lificato affinché compia le operazioni di installazione,
regolazione e manutenzione tecnica nel modo più corret-
to e secondo le norme in vigore.
Importante: qualsiasi intervento di regolazione, manu-
tenzione etc. deve essere eseguito con l’elettrodomesti-
co elettricamente disinserito.
Posizionamento
La cucina è predisposta con grado di protezione contro i
riscaldamenti eccessivi di tipo X, è pertanto possibile l’in-
stallazione a fianco di mobili la cui altezza non superi quella
del piano di lavoro.
Livellamento (presente solo su alcuni modelli)
Nella parte inferiore dell’apparecchio si trovano 4 piedini
di sostegno regolabili con viti che permettono di migliora-
re il livellamento dell’apparecchio, se necessario. E’ indi-
spensabile che l’apparecchio sia posizionato in modo
uniforme.
Montaggio gambe (presente solo su alcuni modelli)
Vengono fornite delle gambe da montare ad incastro sot-
to la base della cucina.
Montaggio cavo di alimentazione
Apertura morsettiera:
Servendosi di un cacciavite, fare leva sulle linguette
laterali del coperchio della morsettiera;
Tirare ed aprire il coperchio della morsettiera.
Per la messa in opera del cavo eseguire le seguenti ope-
razioni:
svitare la vite del serracavo e le viti dei contatti
Nota: i ponticelli vengono predisposti dalla Fabbrica
per il collegamento a 230V monofase (fig. A).
per effettuare i collegamenti elettrici delle fig. C e fig.
D, utilizzare i due ponticelli alloggiati dentro la scatola
(fig. B - riferimento "P")
fissare il cavo di alimentazione nell’apposito fermacavo
e chiudere il coperchio.
N L
220-230V 1N~
H07RR-F 3x6 CEI-UNEL 35363
1
3
2
4
5
Fig. A
N
L2
L1
L3
P
Fig. B
N L1 L2
380-400V 2N~
H05RR-F 4x4 CEI-UNEL 35363
1
3
2
4
5
Fig. C
N L1 L3L2
380-400V 3N~
H05RR-F 5x2.5 CEI-UNEL 35363
1
3
2
4
5
Fig. D
Collegamento del cavo di alimentazione alla rete
Montare sul cavo una spina normalizzata per il carico in-
dicato sulla targhetta caratteristiche, nel caso di collega-
mento diretto alla rete è necessario interporre tra l’appa-
recchio e la rete un interruttore omnipolare con apertura
minima fra i contatti di 3 mm. dimensionato al carico e
rispondente alle norme in vigore (il filo di terra, di colore
giallo-verde, non deve essere interrotto dall’interruttore).
Il cavo di alimentazione deve essere posizionato in modo
5
che non raggiunga in nessun punto una temperatura su-
periore di 50°C a quella ambiente.
Prima di effettuare l’allacciamento accertarsi che:
la valvola limitatrice e l’impianto domestico possano
sopportare il carico dell’apparecchiatura (vedi targhetta
caratteristiche);
l’impianto di alimentazione sia munito di efficace col-
legamento a terra secondo le norme e le disposizioni
di legge;
la presa o l’interruttore omnipolare siano facilmente
raggiungibili con l’apparecchio installato.
6
Caratteristiche tecniche
La cucina con forno elettrico
Forno
Dimensioni (HxLxP): 32x40,5x39,5 cm
Volume: 52 Litri
Assorbimento Max Forno: 2250 W
Dimensioni utili del cassetto scaldavivande:
larghezza cm. 46
profondità cm. 42
altezza cm. 8.5
Piano Elettrico
Dietro destra: 2100 W
Avanti destra: 1200 W
Avanti sinistra: 1700 W
Dietro sinistra: 1200 W
Assorbimento Max Piano Elettrico: 6200 W
Voltaggio e Frequenza
230V/400V 3N~ 50/60 Hz
ENERGY LABEL
Direttiva 2002/40/CE sull'etichetta dei forni elettrici
Norma EN 50304
Consumo energia dichiarazione Classe convezione Naturale
funzione di riscaldamento: Statico
7
Questa apparecchiatura è conforme alle seguenti
Direttive Comunitarie:
- 73/23/CEE del 19/02/73 (Bassa Tensione) e successi-
ve modificazioni;
- 89/336/CEE del 03/05/89 (Compatibilità Elettromagne-
tica) e successive modificazioni;
- 93/68/CEE del 22/07/93 e successive modificazioni.
A Cruscotto
B Griglia ripiano del forno
C Leccarda o piatto di cottura
D Piedini regolabili
H La spia di funzionamento delle piastre elettriche
L Manopola di selezione forno
M Manopola termostato
N Manopole di comando delle piastre elettriche
O La spia termostato forno
S Contaminuti
N
O
L M S
H
A
D
B
C
D
7
Istruzioni per l’uso
La selezione delle varie funzioni presenti nella cucina avvie-
ne agendo sui dispositivi ed organi di comando posti sul
cruscotto dello stesso.
Attenzione: Alla prima accensione consigliamo di far fun-
zionare il forno a vuoto per circa mezz’ora con il termostato
al massimo e a porta chiusa. Quindi trascorso tale tempo
spegnerlo, aprite la porta ed areare il locale. L’odore che
talvolta si avverte durante questa operazione è dovuto al-
l’evaporazione delle sostanze usate per proteggere il forno
durante l’intervallo di tempo che intercorre tra la produzione
e l’installazione del prodotto.
Attenzione: Utilizzare il primo ripiano dal basso, posizio-
nandoci la leccarda in dotazione per raccogliere sughi e/o
grassi, solamente nel caso di cotture al grill o con girarrosto
(presente solo su alcuni modelli). Per le altre cotture non
utilizzate mai il primo ripiano dal basso e non appoggiate
mai oggetti sul fondo del forno mentre state cuocendo perchè
potreste causare danni allo smalto. Ponete sempre i Vostri
recipienti di cottura (pirofile, pellicole di alluminio, ecc. ecc.)
sulla griglia in dotazione con l’apparecchio, appositamente
inserita nelle guide del forno.
Forno Statico
Posizione manopola termostato “M”: Tra 60°C e Max.
In questa posizione si accendono i due elementi riscaldanti
inferiore e superiore. E’ il classico forno della nonna che è
stato però portato ad un eccezionale livello di distribuzione
della temperatura e di contenimento dei consumi. Il forno
statico resta insuperato nei casi in cui si debbano cucinare
piatti i cui ingredienti risultano composti da due o più elementi
che concorrono a formare un piatto unico come ad esempio:
cavoli con costine di maiale, baccalà alla spagnola,
stoccafisso all’anconetana, teneroni di vitello con riso etc...
Ottimi risultati si ottengono nella preparazione di piatti a base
di carni di manzo o vitello quali: brasati, spezzatini, gulasch,
carni di selvaggina, cosciotto e lombo di maiale etc... che
necessitano di cottura lenta con costante aggiunta di liquidi.
Resta comunque il miglior sistema di cottura per i dolci, per
la frutta e per le cotture con recipienti coperti specifici per le
cotture al forno. Nella cottura al forno statico utilizzate un
solo ripiano, in quanto su più ripiani si avrebbe una cattiva
distribuzione della temperatura. Usando i diversi ripiani a
disposizione potrete bilanciare la quantità di calore tra la parte
superiore ed inferiore. Se la cottura necessita di maggior
calore dal basso o dall’alto, utilizzate rispettivamente i ripiani
inferiori o superiori.
Forno Dolce
Posizione manopola termostato “M”: Tra 60°C e Max.
Si accende l’elemento riscaldante inferiore.
Questa funzione è indicata per la cottura di cibi delicati, in
particolare i dolci che necessitano di lievitazione, in quanto
viene facilitata dal calore proveniente dal basso.
Viene fatto notare che le temperature più elevate vengono
raggiunte in tempi piuttosto lunghi, pertanto in questi casi è
consigliabile utilizzare la funzione “Forno Statico”.
Forno “sopra”
Posizione manopola termostato “M”: Tra 60°C e Max.
Si accende l’elemento riscaldante superiore.
Questa funzione può essere utilizzata per ritocchi di cottura.
Grill
Posizione manopola termostato “M”: Max.
Si accende l’elemento riscaldante superiore centrale.
La temperatura assai elevata e diretta del grill consente la
immediata rosolatura superficiale dei cibi che, ostacolando
la fuoriuscita dei liquidi, li mantiene più teneri internamente.
La cottura al grill è particolarmente consigliata per quei piatti
che necessitano di elevata temperatura superficiale:
bistecche di vitello e manzo, entrecôte, filetto, hamburger
etc...
Alcuni esempi di utilizzo sono riportati al paragrafo “Consigli
pratici per la cottura”.
La luce forno
Si accende ruotando la manopola “L” sul simbolo
. Illumi-
na il forno e resta accesa quando sia messo in funzione un
qualsivoglia elemento elettrico riscaldante del forno.
Il contaminuti
Per utilizzare il contaminuti occorre caricare la suoneria
ruotando la manopola “S”di un giro quasi completo in senso
orario
4; quindi, tornando indietro 5, impostare il tempo
desiderato facendo coincidere con il riferimento fisso del
frontalino il numero corrispondente ai minuti prefissati.
La spia termostato forno (O)
Indica la fase di riscaldamento dello stesso, il suo spegni-
mento segnala il raggiungimento all’interno del forno della
temperatura impostata con la manopola. A questo punto l’al-
ternativo accendersi e spegnersi di questa spia indica che il
termostato sta lavorando correttamente per mantenere co-
stante la temperatura del forno.
Il girarrosto (solo su alcuni modelli)
Per azionare il girarrosto procedere nel modo seguente:
a) posizionare la leccarda al 1° ripiano;
b) inserire l’apposito sostegno del girarrosto al 3° ripiano e
posizionare lo spiedo inserendolo, attraverso l’apposito foro,
nel girarrosto posizionato nel retro del forno;
c) azionare il girarrosto selezionando con la manopola L” la
posizione
.
8
Nella cottura al forno utilizzate una sola leccarda o griglia
alla volta. Questa va posizionata sulle guide inferiori o
superiori a seconda che la cottura necessiti di maggior
calore dal basso o dall’alto.
Preriscaldamento
Nel caso in cui sia necessario preriscaldare il forno, in
linea di massima tutte le volte in cui si cuociono cibi lievi-
tati, è consigliabile utilizzare la funzione “forno statico” che
consente di raggiungere la temperatura in breve tempo.
Alla fine del preriscaldamento, indicata dallo spegnimen-
to della spia rossa E”, selezionate la funzione di cottura
più indicata.
Cottura del pesce e della carne
Per le carni bianche, i volatili ed il pesce utilizzate tempe-
rature da 180 °C a 200 °C.
Per le carni rosse che si vuole siano ben cotte all’esterno
conservando all’interno il sugo, è bene utilizzare una tem-
peratura iniziale alta (200°C-220°C) per breve tempo, per
poi diminuirla successivamente.
In generale, più grosso è l’arrosto, più bassa dovrà esse-
re la temperatura e più lungo il tempo di cottura. Ponete la
carne da cuocere al centro della griglia ed inserite sotto
la griglia la leccarda per raccogliere i grassi.
Inserite la griglia in modo che il cibo si trovi al centro del
forno. Se volete più calore da sotto, utilizzate i ripiani più
bassi. Per ottenere arrosti saporiti (in particolare anatra e
selvaggina) bardate la carne con lardo o pancetta e posi-
zionatela in modo che sia nella parte superiore.
Cottura dei dolci
Nella cottura dei dolci preriscaldate sempre il forno e, per
evitare un abbassamento del dolce, non aprite la porta
durante la cottura. In generale:
Dolce troppo secco
La prossima volta impostate una temperatura di10°C
superiore e riducete il tempo di cottura.
Dolce si abbassa
Usate meno liquido o abbassate la temperatura di
10°C.
Dolce scuro superiormente
Inseritelo ad altezza inferiore, impostate una
temperatura più bassa e prolungate la cottura.
Buona cottura esterna, ma interno colloso
Usate meno liquido, riducete la temperatura,
aumentate il tempo di cottura.
Dolce non si stacca dallo stampo
Ungete bene lo stampo e cospargetelo anche con un
pò di farina.
Utilizzo del grill
Utilizzate la funzione
“grill” posizionando il cibo al
centro della griglia (posta al 3° o 4° ripiano partendo dal
basso), dato che risulta accesa solamente la parte cen-
trale della resistenza superiore.
Utilizzare il primo ripiano dal basso, posizionandoci la
leccarda in dotazione per raccogliere sughi e/o grassi.
Quando si utilizza tale funzione, si raccomanda di impo-
stare il termostato al massimo. Questo, però, non signifi-
ca che non si possano utilizzare temperature inferiori, sem-
plicemente regolando la manopola del termostato sulla
temperatura desiderata.
Nei modelli provvisti di girarrosto
, nella funzione “grill
è possibile utilizzare il kit spiedo in dotazione. In questo
caso, effettuare la cottura con la porta del forno chiusa,
posizionando il kit spiedo al 3° ripiano (partendo dal basso)
e la leccarda al 1° per raccogliere sughi e/o grassi.
Importante: effettuare la cottura al grill con porta del
forno chiusa, ciò per ottenere migliori risultati ed un sen-
sibile risparmio di energia (10% circa).
Pertanto i migliori risultati nell’utilizzo delle funzioni
grill si ottengono disponendo la griglia sugli ultimi
ripiani partendo dal basso (vedi tabella cottura)
dopodiché, per raccogliere i grassi ed evitare la for-
mazione di fumo, disponete la leccarda in dotazione
nel primo ripiano dal basso.
Consigli pratici per la cottura
9
Le manopole di comando delle piastre elettriche del
piano di cottura (N)
Le cucine possono essere dotate di piastre elettriche nor-
mali e rapide in varie combinazioni (le piastre rapide si di-
stinguono dalle altre per la presenza di un bollo rosso al
centro). Per evitare dispersioni di calore e danni alle piastre
è bene usare recipienti con fondo piano e di diametro non
inferiore a quello della piastra. Nella tabella sono riportate le
corrispondenze fra la posizioni indicate sulle manopole e
l’uso per il quale le piastre sono consigliate.
Pos. Piastra normale o rapida
0 Spento
1
Cottura di verdure, pesci
2
Cottura di patate (a vapore) minestre, ceci,
fagioli
3
Proseguimento di cottura di grandi quantità di
cibi, minestroni
4 Arrostire (medio)
5 Arrostire (forte)
6
Rosolare o raggiungere bollitura in poco tempo
La spia di funzionamento delle piastre elettriche (H)
Risulta accesa quando sia messo in funzione un qualsivoglia
elemento elettrico riscaldante del piano di cottura eventual-
mente provvisto di piastre elettriche.
Consigli pratici per l'uso del piano in ceramica
Istruzioni sull'uso del piano di cottura in ceramica
Descrizione
Il piano di cottura è munito di 4 elementi riscaldanti ra-
dianti. Questi riscaldatori sono incorporati al di sotto della
superficie del piano di cottura (zone che diventano rosse
durante il funzionamento):
A. Elementi riscaldanti radianti
B. Luci che indicano se la temperatura dei riscaldatori
corrispondenti supera i 60°C, anche se la zona del pia-
no di cottura è stata spenta.
AA
B
Descrizione degli elementi riscaldanti
Gli elementi riscaldanti radianti sono costituiti da ele-
menti riscaldanti circolari, che diventano rossi soltanto
dopo 10-20 secondi dall'accensione.
Istruzioni per l'uso del piano di cottura in
vetroceramica
Per ottenere dal piano di cottura i migliori risultati possibi-
li, seguire alcune regole fondamentali al momento di pre-
parare o cucinare i cibi.
· Sui piani di cottura in vetroceramica è possibile utiliz-
zare tutti i tipi di pentole e padelle. Tuttavia, la superfi-
cie inferiore deve essere perfettamente piana. Natu-
ralmente, più spesso è il fondo della pentola o della
padella, più uniformemente viene distribuito il calore.
· Controllare che la base della padella copra completa-
mente la corona: ciò permetterà di sfruttare appieno il
calore prodotto
· Controllare che la base della padella sia sempre asciut-
ta e pulita: ciò garantisce non solo che il contatto sia
quello ottimale, ma anche che le padelle e i piani di
cottura durino a lungo.
· Non utilizzare le stesse padelle che vengono utilizzate
per la cottura sui bruciatori a gas, perché la forza del
calore di questi ultimi potrebbe deformare la base del-
la padella e non darà gli stessi risultati se poi viene
utilizzata su di un piano di cottura in vetroceramica.
10
Manutenzione ordinaria e pulizia della cucina
Prima di ogni operazione disinserire elettricamente
la cucina. Per una lunga durata della cucina è indispen-
sabile eseguire frequentemente una accurata pulizia ge-
nerale, tenendo presente che:
· per la pulizia non utilizzare apparecchi a vapore
le parti smaltate e i pannelli autopulenti, se presenti,
vanno lavate con acqua tiepida senza usare polveri
abrasive e sostanze corrosive che potrebbero rovinar-
le;
l’interno del forno va pulito, con una certa frequenza,
quando è ancora tiepido usando acqua calda e deter-
sivo, risciacquando ed asciugando poi accuratamen-
te;
l’acciaio inox può rimanere macchiato se rimane a con-
tatto per lungo tempo con acqua fortemente calcarea
o con detergenti aggressivi (contenenti fosforo). Si con-
siglia di sciacquare abbondantemente ed asciugare
dopo la pulizia. E’ inoltre opportuno asciugare even-
tuali trabocchi d’acqua.
Cleaning the hob surface
Prior to cooking, the hob surface should always be cleaned
using a damp cloth to remove any dust or stray food
particles. The hob surface should be regularly cleaned
with a lukewarm solution of water and a mild detergent.
Periodically it may be necessary to use a proprietary
ceramic hob cleaner. First remove all spilt food and fat
with a window scrape, preferably the razor blade type
(not supplied) or, failing that, the fixed blade
razor edge type (see Fig. A). Then clean the hob while it
is still warm to the touch with a suitable cleaner and paper
towel.
Then rinse it and wipe it dry with a clean cloth .If aluminium
foil or plastic items are accidentally allowed to melt on the
hob surface they should be immediately removed from
the hot cooking area with a scraper. This will avoid any
possible damage to the surface. This also applies to sugar
or any food with a high sugar content.
Do not use abrasive sponges or scourers of any type.
Corrosive cleaners such as oven sprays and stain
removers should also not be used (see Fig. B).
Fig. A Fig. B
Prodotti specifici per la
pulizia del vetroceramica
Dove acquistarli
Raschietto a lametta e Lamette
di ricambi
Hobbistica e
Ferramenta
Stahl-Fix
SWISSCLEANER
WK TOP
Altri prodotti per vetroceramica
Casalinghi
Fai-Da-Te
Ferramenta
Supermercati
Sostituzione della lampada nel vano forno
Togliere l’alimentazione al forno tramite l’interruttore
omnipolare utilizzato per il collegamento del forno al-
l’impianto elettrico, o scollegare la spina, se accessi-
bile;
Svitare il coperchio in vetro del portalampada;
Svitare la lampada e sostituirla con una resistente ad
alta temperatura (300°C) con queste caratteristiche:
- Tensione 230V
- Potenza 25W
- Attacco E14
Rimontare il coperchio in vetro e ridate alimentazione
al forno.
11
Consigli pratici per la cottura
Posizione
manopola
selezione
Cibo da cucinare Peso
(Kg)
Posizione di
cottura ripiani
dal basso
Tempo di pre-
riscaldamento
(minuti)
Posizione
manopola
termostato
Tempo di
cottura
(minuti)
1 Statico
Anatra
Arrosto di vitello o
manzo
Arrosto di maiale
Biscotti (di frolla)
Crostate
Lasagne
Agnello
Sgombro
Plum-cake
Big
Pan di spagna
Torte salate
1
1
1
-
1
1
1
1
1
0.3
0.5
1.5
3
3
3
3
3
3
2
2
2
3
3
3
15
15
15
15
15
10
10
10
10
10
10
15
200
200
200
180
180
190
180
180
170
180
170
200
65-75
70-75
70-80
15-20
30-35
35-40
50-60
30-35
40-50
30-35
20-25
30-35
2 Forno Dolce
Torte lievitate
Crostate
Torte di frutta
Brioches
0,5
1
1
0,5
3
3
3
3
15
15
15
15
160
180
180
160
30-40
35-40
50-60
25-30
3 Forno
Sopra
Ritocchi di cottura - 3/4 15 220 -
4 Grill
Sogliole e seppie
Spiedini di calamari e
gamberi
Filetto di merluzzo
Verdure alla griglia
Bistecca di vitello
Cotolette
Hamburger
Sgombri
Toast
1
1
1
1
1
1
1
1
n.° 4
4
4
4
3/4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
Max
Max
Max
Max
Max
Max
Max
Max
Max
8-10
6-8
10
10-15
15-20
15-20
7-10
15-20
2-3
Con girarrosto (ove
presente)
Vitello allo spiedo
Pollo allo spiedo
Agnello allo spiedo
1.0
1.5
1.0
-
-
-
5
5
5
Max
Max
Max
80-90
70-80
70-80
NB: i tempi di cottura sono indicativi e possono essere modificati in base ai propri gusti personali. Nelle cotture al
grill la leccarda va posta sempre al 1° ripiano a partire dal basso.
12
Important
1 This appliance is intended for non-professional use within
the home.
2 Before using the appliance, carefully read the instructions
contained in this manual, as they provide important
information for ensuring safe installation, use and
maintenance. Keep this manual as a reference guide.
3 Remove the packing and make sure the appliance hasn’t been
damaged during transport. If you have any doubts, don’t use
the appliance. Call a qualified technician for assistance. For
safety, keep packing materials (plastic bags, polystyrene foam,
tacks, etc.) away from children.
4 The appliance must be installed by a qualified technician in
accordance with the manufacturer’s instructions. No liability for
injury or damage to persons, animals or property will be accepted
by the manufacturer arising from failure to follow these
instructions.
5 The electrical safety of this appliance is ensured only if it is
correctly connected to an efficiently earthed system in
accordance with electrical safety regulations. Make sure this
basic safety requirement has been complied with. If in doubt,
have it checked by a qualified technician. No liability for damage
will be accepted by the manufacturer because of defective
earthing.
6 Before connecting the appliance, make sure the specifications
on the rating plate correspond with those of your power supply.
7 Check that your supply and sockets are sufficient for the total
load taken by your appliance which is stated on the rating plate.
If you have any doubts, contact a qualified technician for service.
8 A multipole circuit breaker with a space between contacts of 3
mm or more must be fitted for installation
9 If the socket and cooker plug are not compatible, have the socket
replaced with a suitable model by a qualified technician who
should also check that the cross-section of the socket cable is
suited to the power absorbed by the appliance. The use of
adaptors, multiple sockets and/or extensions, is not
recommended. If their use can not be avoided, remember to
use only single or multiple adapters and extensions which comply
with current safety regulations. In these cases, never exceed
the maximum current capacity indicated on the single adaptor
or extension and the maximum power indicated on the multiple
adapter.
10 Do not leave the appliance plugged in if it is not necessary.
Switch off the main switch and gas cock when you are not using
the cooker.
11 The openings and slots used for ventilation and dispersion
of heat must never be closed or plugged.
12 The user must not replace the supply cable of this appliance.
Always call an after-sales servicing centre authorised by the
manufacturer in the case of cable damage or replacement.
13 This appliance must be used for the purpose for which it was
expressly designed.
Any other use (e.g. heating rooms) is considered to be improper
and consequently dangerous.
The manufacturer declines all responsibility for damage resulting
from improper and irresponsible use.
14 A number of fundamental rules must be followed when using
electrical appliances. The following are of particular importance:
· do not touch the appliance when your hands or feet are wet
· do not use the appliance barefooted
· do not use extensions, but if these are necessary caution
must be exercised.
· never pull the power supply cable or the appliance to unplug
the appliance plug from the mains.
· never leave the appliance exposed to atmospheric agents
(rain, sun etc.)
· do not allow children or persons who are not familiar with
the appliance to use it, without supervision.
15 Always unplug the hob from the mains or switch off the main
switch before cleaning or carrying out maintenance operations.
16 If the surface of the glass breaks, disconnect the appliance
immediately. For repairs call only an authorised after-sales
servicing centre and request the use of original spare parts
only. Failure to comply with the above may compromise the
safety of the appliance.
17 If you are no longer using the appliance, remember to make it
unserviceable by unplugging the appliance from the mains and
cutting the supply cable. Also make all potentially dangerous
parts of the appliance, safe, above all for children who could
play with the appliance.
18 The vitreous china hob is resistant to temperature fluctuations
and shockproof. Remember however that sharp kitchen tools
or cutters may break the surface of the hob. If this happens,
unplug the cooker immediately from the mains and call your
local servicing centre.
19 Remember that the cooking surface remains hot for at least
half an hour after you switch off the surface. Do not place
containers or other objects on the hot surface.
20 Avoid setting anything on the glass surface of the cooktop.
21 Do not turn on the cooking surfaces if there are sheets of
aluminium foil or plastic on the hob.
22 Keep away from the hot surfaces.
23 When using small electrical household appliances close to the
hob, ensure that the power cable does not rest on the hot
surfaces
24 Keep pot handles turned inwards to avoid knocking the pot off
the hob.
25 When you turn on the cooking surface always place a pot on
the surface immediately as it will otherwise overheat very quickly
and possibly damage the heating elements.
26 Preliminary instructions. The glass sealant utilised may leave
traces of grease on the glass. Remember to wipe these away
with a normal non abrasive detergent before you turn on the
appliance. During the first few hours of use there may be a
smell of rubber which will disappear very quickly.
27 When the appliance is in use, the heating elements and
some parts of the oven door become extremely hot. Make
sure you don't touch them and keep children well away.
28 Make sure the knobs are in the “•”/”o” position when the appli-
ance is not in use.
29 If the cooker is placed on a pedestal, take the necessary
precautions to prevent the same from sliding off the pedestal
itself.
To maintain the EFFICIENCY and SAFETY of this appliance, we recommend:
call only the Service Centers authorized by the manufacturer
always use original Spare Parts
13
Installation Instructions
The following instructions should be read by a qualified
technician to ensure that the appliance is installed,
regulated and technically serviced correctly in compliance
with current regulations.
Important: The power supply to the appliance must be
cut off before any adjustments or maintenance work is
done on it.
Positioning
The cooker is manufactured with type X degree protection
against overheating.
Levelling Your Appliance (only on certain models)
4 support feet which are adjusted using screws are located
in the lower part of the cooker. These level off the oven
when necessary. It is essential that the cooker be standing
level.
Mounting the legs (only on certain models)
Press-fit legs are supplied which fit under the base of your
cooker.
Fitting on a Power Supply Cable
Opening the terminal board:
Using a screwdriver, prise on the side tabs of the
terminal board cover;
Pull open the cover of the terminal board.
To install the cable, proceed as follows:
unscrew the wire clamp screw and the contact screws
Note: the jumpers are factory-set for a single-phase
230V connection (Fig. A).
to make the electrical connections illustrated in fig. C
and fig. D, use the two jumpers housed in the box (fig.
B - reference “P”)
fasten the supply cable in place with the clamp and
close the cover of the terminal board.
N L
220-230V 1N~
H07RR-F 3x6 CEI-UNEL 35363
1
3
2
4
5
Fig. A
N
L2
L1
L3
P
Fig. B
N L1 L2
380-400V 2N~
H05RR-F 4x4 CEI-UNEL 35363
1
3
2
4
5
Fig. C
N L1 L3L2
380-400V 3N~
H05RR-F 5x2.5 CEI-UNEL 35363
1
3
2
4
5
Fig. D
Connecting the supply cable to the mains
Install a standardised plug corresponding to the load
indicated on the data plate. When connecting the cable
directly to the mains, install an omnipolar circuit-breaker
with a minimum contact opening of 3 mm between the
appliance and the mains. The omnipolar circuit breaker
should be sized according to the load and should comply
with current regulations (the green-yellow earth wire should
not be interrupted by the circuit breaker). The supply cable
should be positioned so that it does not reach a tempera-
14
Oven
Dimensions (HxWxD): 32x40.5x39.5 cm
Volume: 52 Litres
Max. Oven Power Absorption: 2250 W
Innder dimensions of the plate plate warmer:
Width: 46 cm
Depth: 42 cm
Height: 8.5 cm
Ceramic Hob
Back Right: 2100 W
Front Right: 1200 W
Front Left: 1700 W
Back Left: 1200 W
Hob Ceramic absorption Max: 6200 W
Voltage and Frequency
230V/400V 3N~ 50/60Hz
ENERGY LABEL
Directive 2002/40/EC on the label of electric ovens
Norm EN 50304
Declared energy consumption for Natural convection Class
heating mode: Convection
This appliance conforms with the following European
Economic Community directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent
modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic
Compatibility) and subsequent modifications;
- 93/68/EEC of 22/07/93 and subsequent modifications.
Cooker with electric oven
ture of more than 50°C with respect to the room tempera-
ture, anywhere along its length.
Before making the connection, check that:
the limiter valve and the home system can support the
appliance load (see data plate);
the mains are properly earthed in compliance with
current directives and regulations;
there is easy access to the socket and omnipolar circuit
breaker, once the hob has been installed.
A Control Panel
B Oven Rack
C Dripping Pan or Baking Sheet
D Adjustable Feet
H Electric hotplate indicator light
L Selector Knob
M Thermostat Knob
N Electric hotplate control knobs
O Thermostat Light
S Timer Knob
Technical Characteristics
N
O
L M S
H
A
D
B
C
D
15
How To Use Your Appliance
The various functions featured with the oven are controlled
using the knobs and buttons on the control panel.
Notice: The first time you use your appliance, we recom-
mend that you set the thermostat to the highest setting and
leave the oven on for about half an hour with nothing in it,
with the oven door shut. Then, open the oven door and let
the room air. The odour that is often detected during this
initial use is due to the evaporation of substances used to
protect the oven during storage and until it is installed.
Attention: Only use the bottom shelf of the oven when using
the rotisserie to cook (where present). For all other types of
cooking, never use the bottom shelf and never place anything
on the bottom of the oven when it is in operation because
this could damage the enamel. Always place your cookware
(dishes, aluminium foil, etc. etc.) on the grate provided with
the appliance inserted especially along the oven guides.
Convection Mode
Position of thermostat knob “M”: between 60°C and Max.
On this setting, the top and bottom heating elements come
on. This is the classic, traditional type of oven which has
been perfected, with exceptional heat distribution and re-
duced energy consumption. The convection oven is still un-
equalled when it comes to cooking dishes made up of sev-
eral ingredients, e.g. cabbage with ribs, Spanish style cod,
Ancona style stockfish, tender veal strips with rice, etc. Ex-
cellent results are achieved when preparing veal or beef-
based dishes as well (braised meats, stew, goulash, wild
game, ham etc.) which need to cook slowly and require bast-
ing or the addition of liquid. It nonetheless remains the best
system for baking cakes as well as fruit and cooking using
covered casserole dishes for oven baking. When cooking in
convection mode, only use one dripping pan or cooking rack
at a time, otherwise the heat distribution will be uneven. Us-
ing the different rack heights available, you can balance the
amount of heat between the top and the bottom of the oven.
Select from among the various rack heights based on whether
the dish needs more or less heat from the top.
Pastry Mode
Position of thermostat knob “M”: Between 60°C and Max.
The bottom heating element comes on.
This mode is ideal for baking and cooking delicate foods -
especially cakes that need to rise because the heat coming
from the bottom helps the leavening process.
Please note that it takes a considerable amount of time for
the higher temperatures to be reached, therefore we recom-
mend you use the “Convection Mode” in these cases.
“Top” Oven
Position of thermostat knob “M”: Between 60°C and Max.
The top heating element comes on.
This mode can be used to brown food at the end of cooking.
Grill
Position of thermostat knob “M”: Max
The top central heating element comes on.
The extremely high and direct temperature of the grill makes
it possible to brown the surface of meats and roasts while
locking in the juices to keep them tender. The grill is also
highly recommended for dishes that require a high tempera-
ture on the surface: beef steaks, veal, rib steak, filets, ham-
burgers etc...
Some grilling examples are included in the “Practical Cook-
ing Advice” paragraph.
The oven light
Set knob “L to the
symbol to turn it on. It lights the oven
and stays on when any of the electrical heating elements in
the oven come on.
Thermostat Light (O)
This light indicates that the oven is heating. When it turns off,
the temperature inside the oven has reached the setting made
with the thermostat knob. At this point, the light will turn on
and off as the oven maintains the temperature at a constant
level.
Timer Knob (S)
In order to use the timer, it must be wound by turning the "S"
knob almost one complete turn in the clockwise direction
. Then, turning it back , set the desired time by lining
up the number for the minutes with the mark on the control
panel.
The turnspit (only on a few models)
To start the turnspit, proceed as follows:
a) place the oven tray on the 1st rack;
b) insert the special turnspit support on the 3rd rack and
position the spit by inserting it through the special hole
into the turnspit at the back of the oven;
c) start the turnspit using knob L to select setting
.
16
Practical Cooking Advice
When cooking in the oven, use only one dripping pan or
rack at a time. Select from among the top or bottom rack
heights based on whether the dish needs more or less
heat from the top.
Preheating
If the oven must be preheated (this is generally the case
when cooking leavened foods), we recommend you use
the “convection mode” to reach the desired temperature
as quickly as possible. When preheating is over, which is
indicated by the red light E going out, select the
required cooking mode.
Cooking Fish and Meat
When cooking white meat, fowl and fish, use temperature
settings from 180 °C to 200 °C.
For red meat that should be well done on the outside while
tender and juicy in the inside, it is a good idea to start with
a high temperature setting (200°C-220°C) for a short time,
then turn the oven down afterwards.
In general, the larger the roast, the lower the temperature
setting. Place the meat on the centre of the grid and place
the dripping pan beneath it to catch the fat.
Make sure that the grid is inserted so that it is in the centre
of the oven. If you would like to increase the amount of
heat from below, use the low rack heights. For savoury
roasts (especially duck and wild game), dress the meat
with lard or bacon on the top.
Baking Cakes
When baking cakes, always preheat the oven and do not
open the oven door during baking to prevent the cake
from dropping. In general:
Pastry dropped
Use less liquid or lower the temperature by 10°C.
Pastry is too dark on top
Place it on a lower rack, lower the temperature, and
increase the cooking time.
Cooked well on the inside but sticky on the
outside
Use less liquid, lower the temperature, and increase
the cooking time.
The pastry sticks to the pan
Grease the pan well and sprinkle it with a dusting of
flour.
I used more than one level and they are not all at
the same cooking point
Use a lower temperature setting. It is not necessary to
remove the food from all the racks at the same time.
Using the Grill
Use the
grill mode, placing the food under the cen-
tre of the grill (situated on the 3rd or 4th rack form the
bottom) because only the central part of the top heating
element is turned on.
Use the bottom rack (1st from the bottom), placing the
dripping pan provided to collect any sauce and/or grease
and prevent the same from dripping onto the oven bot-
tom.
When using this mode, we recommend you set the ther-
mostat to the highest setting. However, this does not mean
you cannot use lower temperatures, simply by adjusting
the thermostat knob to the desired temperature.
In models fitted with a rotisserie
, you can use the spit
kit provided when using the grill mode. In this case, cook
with the oven door shut, placing the spit kit on the third
oven rack from the bottom and the dripping pan on the
bottom rack to collect any sauce and /or dripping fat.
Important: always use the grill with the oven door shut.
This will allow you both to obtain excellent results and to
save on energy (approximately 10%).
Therefore the best results when using the grill modes
are obtained by placing the grid on the lower racks
(see cooking table) then, to prevent fat and grease
from dripping onto the bottom of the oven and smoke
from forming, place a dripping-pan on the 1st oven
rack from the bottom.
17
The control knobs for the hob electric hotplates (N)
The cookers can be fitted with normal and rapid electric
hotplates in a variety of combinations (the rapid hotplates
can be distinguished from the rest by the red boss in the
centre of the same). To avoid any heat loss and damage to
the hotplates, we advise you to use pans with a flat bottom,
with a diameter which matches that of the hotplate itself. The
table contains the different settings indicated on the knobs
and the use for which the hotplates are recommended.
Setting Normal or Fast Plate
0
Off
1 Cooking vegetables, fish
2
Cooking potatoes (using steam) soups,
chickpeas, beans.
3
Continuing the cooking of large quantities
of food, minestrone
4 For roasting (average)
5 For roasting (above average)
6
For browning and reaching a boil in a
short time.
Electric hotplate indicator light (H)
This light comes on when any of the electrical hotplates on a
hob which features electric hotplates have been turned on.
Pratical advice for using the electric plates
User's instructions the ceramic hob
Description
The hobs have been provided with radiant electric heaters.
These heaters are incorporated under the surface of the
hob as zones which redden while they are in use.
A. Cooking area (A).
B. A lights which indicate whether the corresponding
heaters are at a temperature in excess of 60° C; even
if the hob/zone has been switched off.
AA
B
Description of the heating elements
The radiant heating elements are composed of circular
heating elements. They only become red after being turned
on for 10-20 seconds.
Instructions for using the pyroceram top
To obtain the best results from your hob, there are some
basic rules to follow when cooking or preparing food.
· All types of pots and pans may be used on the ceramic
glass cooktop. However, the bottom surface must be
perfectly flat (see Fig. A). Naturally, the thicker the
bottom of the pot or pan, the more uniformly the heat
is distributed.
Fig. A
· Make sure that the base of the pan completely covers
the cooking ring, so as to make full use of the heat
produced (Fig. B)
Fig. B
· Always make sure that the pan base is always dry and
clean so as to guarantee proper contact as well as
longer-lasting pans and the long life-span of the hob.
· Do not use the same pans which are used for cooking
on gas burners. The heat strength of gas burners may
deform the pan base and will not give the same results
if it is subsequently used on a glazed ceramic hob.
18
Selector knob
setting
Food to be cooked Weight
(in kg)
Cooking rack
position from
bottom
Preheating time
(minutes)
Thermostat
knob
setting
Cooking
time
(minutes)
1 Convection
Duck
Roast veal or beef
Pork roast
Biscuits (short pastry)
Tarts
Lasagne
Lamb
Mackerel
Plum-cake
Cream puffs
Sponge-cake
Savoury pies
1
1
1
-
1
1
1
1
1
0.3
0.5
1.5
3
3
3
3
3
3
2
2
2
3
3
3
15
15
15
15
15
10
10
10
10
10
10
15
200
200
200
180
180
190
180
180
170
180
170
200
65-75
70-75
70-80
15-20
30-35
35-40
50-60
30-35
40-50
30-35
20-25
30-35
2 Pastry
Mode
Raised Cakes
Tarts
Fruit cakes
Brioches
0,5
1
1
0,5
3
3
3
3
15
15
15
15
160
180
180
160
30-40
35-40
50-60
25-30
3 Top Oven
Browning food to
perfect cooking
- 3/4 15 220 -
4 Grill
Soles and cuttlefish
Squid and prawn
kebabs
Cod filet
Grilled vegetables
Veal steak
Cutlets
Hamburgers
Mackerels
Toasted sandwiches
1
1
1
1
1
1
1
1
n.° 4
4
4
4
3/4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
Max
Max
Max
Max
Max
Max
Max
Max
Max
8-10
6-8
10
10-15
15-20
15-20
7-10
15-20
2-3
With rotisserie (where
present)
Veal on the spit
Chicken on the spit
Lamb on the spit
1.0
1.5
1.0
-
-
-
5
5
5
Max
Max
Max
80-90
70-80
70-80
NB: cooking times are approximate and may vary according to personal taste. When cooking using the grill, the
dripping pan must always be placed on the 1st oven rack from the bottom.
19
Routine Maintenance and Cleaning
Disconnect the oven from the source of electricity
before performing any maintenance or cleaning. To
ensure a long life for your oven, clean it frequently and
carefully, keeping in mind that:
· Do not use steam equipment to clean the appliance.
· the enamelled parts and the self-cleaning panels
should be washed with warm water without the addition
of abrasive powders or corrosive substances which
could damage the finish;
· stainless steel may become marked if it comes into
contact with very hard water or harsh detergents
(containing phosphorous) for long periods of time. After
cleaning, it is advisable to rinse thoroughly and dry. It
is also recommended to dry any water drops;
· avoid dirt and grease accumulating on the control panel
by cleaning it frequently. Use non-abrasive sponges or
soft cloths to avoid scratching enamelled or shiny steel
parts.
Cleaning the hob surface
Prior to cooking, the hob surface should always be cleaned
using a damp cloth to remove any dust or stray food
particles. The hob surface should be regularly cleaned
with a lukewarm solution of water and a mild detergent.
Periodically it may be necessary to use a proprietary
ceramic hob cleaner. First remove all spilt food and fat
with a window scrape, preferably the razor blade type
(not supplied) or, failing that, the fixed blade
razor edge type (see Fig. A). Then clean the hob while it
is still warm to the touch with a suitable cleaner and paper
towel.
Then rinse it and wipe it dry with a clean cloth .If aluminium
foil or plastic items are accidentally allowed to melt on the
hob surface they should be immediately removed from
the hot cooking area with a scraper. This will avoid any
possible damage to the surface. This also applies to sugar
or any food with a high sugar content.
Do not use abrasive sponges or scourers of any type.
Corrosive cleaners such as oven sprays and stain
removers should also not be used (see Fig. B).
Fig. A Fig. B
Glass ceramic hob cleaners Available from
Window scraper Razor blade
scrapers
DIY Stores
Replacement blades DIY Stores,
supermarkets,
chemists
COLLO luneta
HOB BRITE
Hob Clean
SWISSCLEANER
Boots, Co-op stores,
department stores, Regional
Electricity Company shops,
supermarkets
Replacing the Oven Lamp
Disconnect the oven from the power supply by means
of the omnipolar switch used to connect the appliance
to the electrical mains; or disconnect the plug if it is
accessible.
Remove the glass cover of the lamp-holder.
Remove the lamp and replace it with a lamp resistant
to high temperatures (300°C) with the following speci-
fications:
- Voltage: 230V
- Wattage: 25W
- Socket: E14
Replace the glass cover and connect the oven to the
mains.
20
Ïðåäóïðåæäåíèÿ
1 Äàííîå èçäåëèå ïðåäíàçíà÷àåòñÿ äëÿ íåïðîôåññèîíàëüíîãî
èñïîëüçîâàíèÿ â äîìàøíèõ óñëîâèÿõ.
2 Ïåðåä íà÷àëîì ýêñïëóàòàöèè äàííîãî èçäåëèÿ
ðåêîìåíäóåòñÿ âíèìàòåëüíî ïðî÷èòàòü èíñòðóêöèè,
ñîäåðæàùèåñÿ â äàííîì ðóêîâîäñòâå, ïðåäîñòàâëÿþùèå
âàæíûå ðåêîìåíäàöèè ïî áåçîïàñíîìó îñóùåñòâëåíèþ
ìîíòàæà, ýêñïëóàòàöèè è òåõíè÷åñêîãî îáñëóæèâàíèÿ.
Áåðåæíî ñîõðàíèòå äàííîå ðóêîâîäñòâî äëÿ åãî
êîíñóëüòàöèè â áóäóùåì.
3 Ïîñëå òîãî, êàê Âû îñâîáîäèòå ìàøèíó îò óïàêîâêè, óáåäèòåñü â òîì,
÷òî ìàøèíà íå ïîâðåæäåíà.  ñëó÷àå ñîìíåíèé íå ïîëüçóéòåñü
èçäåëèåì è îáðàòèòåñü ê êâàëèôèöèðîâàííîìó òåõíèêó. ×àñòè óïàêîâêè
(ïëàñòìàññîâûå ìåøêè, âñïåíåííûé ïîëèñòèðîë, ãâîçäè è ò.ä.) íå
äîëæíû ïîïàäàòü â ðóêè äåòåé, òàê êàê ýòè ìàòåðèàëû ïðåäñòàâëÿþò
ñîáîé ïîòåíöèàëüíóþ îïàñíîñòü.
4 Óñòàíîâêà äîëæíà áûòü âûïîëíåíà êâàëèôèöèðîâàííûì
ïåðñîíàëîì â ñîîòâåòñòâèè ñ èíñòðóêöèÿìè ïðîèçâîäèòåëÿ.
Íåïðàâèëüíàÿ óñòàíîâêà ìîæåò ïðè÷èíèòü óùåðá ëþäÿì,
æèâîòíûì èëè èìóùåñòâó, çà êîòîðûé ïðîèçâîäèòåëü íå íåñåò
íèêàêîé îòâåòñòâåííîñòè.
5 Ýëåêòðè÷åñêàÿ áåçîïàñíîñòü äàííîãî èçäåëèÿ ãàðàíòèðóåòñÿ
òîëüêî, åñëè îíî ïðàâèëüíî ïîäñîåäèíåíî ê íàäåæíîé ñèñòåìå
çàçåìëåíèÿ â ñîîòâåòñòâèè ñ äåéñòâóþùèìè ïðàâèëàìè
ýëåêòðè÷åñêîé áåçîïàñíîñòè. Íåîáõîäèìî ïðîâåðèòü ñîáëþäåíèå
ýòîãî âàæíîãî òðåáîâàíèÿ ïî áåçîïàñíîñòè è â ñëó÷àå ñîìíåíèé
ïîðó÷èòü òùàòåëüíóþ ïðîâåðêó ñèñòåìû êâàëèôèöèðîâàííîìó
ïåðñîíàëó. Ïðîèçâîäèòåëü íå íåñåò îòâåòñòâåííîñòè çà âîçìîæíûé
óùåðá, âûçâàííûé îòñóòñòâèåì çàçåìëåíèÿ ýëåêòðè÷åñêîãî
èçäåëèÿ.
6 Ïåðåä ïîäñîåäèíåíèåì ýëåêòðè÷åñêîãî èçäåëèÿ ïðîâåðüòå, ÷òîáû
äàííûå, óêàçàííûå íà çàâîäñêîé òàáëè÷êå, ñîîòâåòñòâîâàëè
õàðàêòåðèñòèêàìè ñåòè ýëåêòðîïèòàíèÿ.
7 Ïðîâåðèòü, ÷òîáû ïîòðåáëåíèå ýëåêòðîýíåðãèè ýëåêòðè÷åñêîãî
èçäåëèÿ è ýëåêòðè÷åñêèõ ðîçåòîê ñîîòâåòñòâîâàëî ìàêñèìàëüíîé
ìîùíîñòè èçäåëèÿ, óêàçàííîé íà çàâîäñêîé òàáëè÷êå.  ñëó÷àå
ñîìíåíèé îáðàòèòåñü ê êâàëèôèöèðîâàííîìó ñïåöèàëèñòó.
8 Ïðè ìîíòàæå èçäåëèÿ íåîáõîäèìî óñòàíîâèòü ìíîãîïîëÿðíûé
ðàçúåäèíèòåëü ñ ðàññòîÿíèåì ìåæäó êîíòàêòàìè ðàâíûì èëè
áîëüøå 3 ìì.
9  ñëó÷àå íåñîâìåñòèìîñòè ýëåêòðîðîçåòêè è ýëåêòðîâèëêè èçäåëèÿ
ïîðó÷èòü çàìåíó ðîçåòêè íà äðóãóþ, ïðèãîäíóþ, êâàëèôèöèðîâàííîìó
ïåðñîíàëó.  ÷àñòíîñòè ýëåêòðèê äîëæåí ïðîâåðèòü, ÷òîáû ñå÷åíèå
ïðîâîäîâ ýëåêòðîðîçåòêè ñîîòâåòñòâîâàëî ïîãëîùàåìîé ìîùíîñòè
ýëåêòðè÷åñêîãî èçäåëèÿ. Êàê ïðàâèëî íå ðåêîìåíäóåòñÿ èñïîëüçîâàòü
ïåðåõîäíèêè, òðîéíèêè è/èëè óäëèíèòåëè. Ïðè íåîáõîäèìîñòè â
èñïîëüçîâàíèè âûøåóêàçàííûõ óñòðîéñòâ ñëåäóåò èñïîëüçîâàòü òîëüêî
ïðîñòûå èëè ìíîæåñòâåííûå ïåðåõîäíèêè è óäëèíèòåëè,
ñîîòâåòñòâóþùèå äåéñòâóþùèì íîðìàòèâàì ïî áåçîïàñíîñòè. Ïðè
ýòîì âàæíî íå ïðåâûøàòü ïðåäåë ðàñõîäà ïî çíà÷åíèþ òîêà, óêàçàííûé
íà ïðîñòîì ïåðåõîäíèêå èëè óäëèíèòåëå, è ìàêñèìàëüíóþ ìîùíîñòü,
óêàçàííóþ íà ìíîæåñòâåííîì ïåðåõîäíèêå.
10 Â ïåðèîä ïðîñòîÿ èçäåëèÿ îòñîåäèíèòå åãî îò ñåòè
ýëåêòðîïèòàíèÿ. Âûêëþ÷èòå ãëàâíûé ðàçúåäèíèòåëü
ýëåêòðè÷åñêîãî èçäåëèÿ, êîãäà îíî íå èñïîëüçóåòñÿ.
11 Íå çàêðûâàéòå âåíòèëÿöèîííûå îòâåðñòèÿ èëè ðåøåòêè
ðàññåèâàíèÿ òåïëà;
12 Ïîëüçîâàòåëü íå äîëæåí ñàìîñòîÿòåëüíî çàìåíÿòü ïðîâîä
ýëåêòðîïèòàíèÿ äàííîãî èçäåëèÿ.  ñëó÷àå ïîâðåæäåíèÿ ïðîâîäà
ýëåêòðîïèòàíèÿ èëè äëÿ åãî çàìåíû îáðàùàéòåñü òîëüêî â öåíòð
òåõíè÷åñêîãî îáñëóæèâàíèÿ, óïîëíîìî÷åííûé ïðîèçâîäèòåëåì
èçäåëèÿ.
13 Äàííîå èçäåëèå äîëæíî èñïîëüçîâàòüñÿ èñêëþ÷èòåëüíî â öåëÿõ, äëÿ
êîòîðûõ îíî áûëî ñïðîåêòèðîâàíî. Ëþáîå äðóãîå åãî èñïîëüçîâàíèå
(íàïðèìåð, îòîïëåíèå ïîìåùåíèÿ) ñ÷èòàåòñÿ íåíàäëåæàùèì è
ñëåäîâàòåëüíî îïàñíûì. Ïðîèçâîäèòåëü íå íåñåò îòâåòñòâåííîñòè çà
âîçìîæíûé óùåðá, âûçâàííûé íåíàäëåæàùèì, íåïðàâèëüíûì è
íåðàçóìíûì èñïîëüçîâàíèåì èçäåëèÿ.
14 Ïðè èñïîëüçîâàíèè ëþáîãî ýëåêòðîïðèáîðà íåîáõîäèìî
ñîáëþäàòü íåêîòîðûå îñíîâíûå ïðàâèëà.  ÷àñòíîñòè:
íå ïðèêàñàéòåñü ê ýëåêòðîïðèáîðó ìîêðûìè èëè âëàæíûìè
ðóêàìè èëè ñ ìîêðûìè íîãàìè.
íå ïîëüçóéòåñü ýëåêòðîïðèáîðîì ñ áîñûìè íîãàìè
èñïîëüçóéòå óäèíèòåëè òîëüêî â ñëó÷àå êðàéíåé
íåîáõîäèìîñòè
íå òÿíèòå çà ïðîâîä ýëåêòðîïèòàíèÿ ýëåêòðîïðèáîðà èëè çà
ñàì ýëåêòðîïðèáîð äëÿ åãî îòñîåäèíåíèÿ îò ýëåêòðîðîçåòêè.
íå ïîäâåðãàéòå ýëåêòðîïðèáîð âîçäåéñòâèþ àòìîñôåðíûõ
îñàäêîâ (äîæäü, ñîëíöå è ò.ä.)
íå ðàçðåøàéòå äåòÿì èëè íåäååñïîñîáíûì ëèöàì
ïîëüçîâàòüñÿ ýëåêòðîïðèáîðîì áåç ïðèñìîòðà
15 Ïåðåä îñóùåñòâëåíèåì ÷èñòêè èëè òåõíè÷åñêîãî îáñëóæèâàíèÿ
ýëåêòðîïðèáîðà îòñîåäèíèòå åãî îò ñåòè ýëåêòðîïèòàíèÿ, âûíóâ
âèëêó èç ðîçåòêè èëè ïðè ïîìîùè îáùåãî âûêëþ÷àòåëÿ.
16 Nel caso in cui si rompa la superficie del vetro, scollegare
immediatamente l'apparecchio. Per l'eventuale riparazione rivolgersi
solamente ad un centro di assistenza tecnica autorizzato e richiedere
l'utilizzo di ricambi originali. Il mancato rispetto di quanto sopra può
compromettere la sicurezza dell'apparecchio.
17 Ïî çàâåðøåíèè ñðîêà ñëóæáû äàííîãî èçäåëèÿ ðåêîìåíäóåòñÿ
âûâåñòè åãî èç ñòðîÿ, îáðåçàâ ïðîâîä ýëåêòðîïèòàíèÿ, âûíóâ ïåðåä
ýòèì âèëêó èç ðîçåòêè. Êðîìå òîãî ðåêîìåíäóåòñÿ îáåçâðåäèòü
ïîòåíöèàëüíî îïàñíûå ÷àñòè èçäåëèÿ â îñîáåííîñòè äëÿ äåòåé,
êîòîðûå ìîãóò èñïîëüçîâàòü âûâåäåííûé èç ñòðîÿ ýëåêòðîïðèáîð
äëÿ èãðû.
16  ñëó÷àå ðàçáèâàíèÿ ñòåêëÿííîé ïîâåðõíîñòè íåçàìåäëèòåëüíî
îòñîåäèíèòå ïðèáîð îò ñåòè ýëåêòðîïèòàíèÿ. Äëÿ âûïîëíåíèÿ
ðåìîíòíûõ ðàáîò îáðàùàéòåñü òîëüêî â óïîëíîìî÷åííûé öåíòð
òåõíè÷åñêîãî îáñëóæèâàíèÿ è òðåáóéòå óñòàíîâêè îðèãèíàëüíûõ
çàïàñíûõ ÷àñòåé. Íåñîáëþäåíèå âûøåóêàçàííûõ ðåêîìåíäàöèé
ìîæåò ñêîìïðîìåòèðîâàòü áåçîïàñíîå ôóíêöèîíèðîâàíèå
èçäåëèÿ.
18 Òâåðäàÿ ñòåêëîêåðàìè÷åñêàÿ âàðî÷íàÿ ïàíåëü ÿâëÿåòñÿ
óñòîé÷èâîé ê ñêà÷êàì òåìïåðàòóðû è ê óäàðàì. Òåì íå ìåíåå
ñëåäóåò ïîìíèòü, ÷òî ëåçâèÿ èëè îñòðûå êóõîííûå ïðèáîðû ìîãóò
ïîâðåäèòü ïîâåðõíîñòü âàðî÷íîé ïàíåëè.  ñëó÷àå ïîâðåæäåíèÿ
ïîâåðõíîñòè âàðî÷íîé ïàíåëè íåçàìåäëèòåëüíî âûíüòå âèëêó
êóõîííîé ïëèòû èç ðîçåòêè è îáðàòèòåñü â ìåñòíûé öåíòð
òåõíè÷åñêîãî îáñëóæèâàíèÿ.
19 Ñëåäóåò ïîìíèòü, ÷òî ïîâåðõíîñòü âàðî÷íîé ïàíåëè îñòàåòñÿ
ãîðÿ÷åé â òå÷åíèå ïðèìåðíî ïîëó÷àñà ïîñëå åå âûêëþ÷åíèÿ. Íå
ñòàâüòå õðóïêóþ ïîñóäó è íå êëàäèòå äðóãèå ïðåäìåòû íà ãîðÿ÷óþ
ïîâåðõíîñòü.
20 Íå ñëåäóåò ñòàâèòü êàêèå-ëèáî ïðåäìåòû íà ñòåêëÿííóþ
ïîâåðõíîñòü âàðî÷íîé ïàíåëè.
21 Íå âêëþ÷àéòå êîíôîðêè âàðî÷íîé ïàíåëè, åñëè íà íåé ëåæàò ëèñòû
ôîëüãè èëè ïëàñòìàññîâûå ïðåäìåòû.
22 Äåðæèòåñü íà áåçîïàñíîì ðàññòîÿíèè îò ãîðÿ÷èõ ïîâåðõíîñòåé.
23 Ïðè èñïîëüçîâàíèè ìåëêèõ áûòîâûõ ýëåêòðîïðèáîðîâ ðÿäîì ñ
êóõîííîé ïëèòîé îáðàùàéòå âíèìàíèå, ÷òîáû èõ ïðîâîä íå êàñàëñÿ
ãîðÿ÷èõ ÷àñòåé ïëèòû.
24 Ïîâîðà÷èâàéòå ðóêîÿòêè êàñòðþëü è ñêîâîðîä òàê, ÷òîáû ñëó÷àéíî
íå çàäåòü èõ è íå îïðîêèíóòü ñ âàðî÷íîé ïàíåëè.
25 Âêëþ÷èâ ïîâåðõíîñòü âàðî÷íîé ïàíåëè, âñåãäà ñðàçó æå ñòàâüòå íà
íåå îäíó êàñòðþëþ âî èçáåæàíèå áûñòðîãî ïåðåãðåâà âàðî÷íîé
ïàíåëè è ïîâðåæäåíèÿ íàãðåâàòåëüíûõ ýëåìåíòîâ.
26 Ïåðåä ïåðâûì âêëþ÷åíèåì âàðî÷íîé ïàíåëè. Íà ñòåêëå ìîãóò
îñòàòüñÿ ñëåäû ãåðìåòèêà, èñïîëüçîâàííîãî äëÿ ãåðìåòèçàöèè
âàðî÷íîé ïàíåëè. Íå çàáóäüòå óäàëèòü îñòàòêè ãåðìåòèêà îáû÷íûì
íåàáðàçèâíûì ìîþùèì âåùåñòâîì ïåðåä íà÷àëîì ýêñïëóàòàöèè
èçäåëèÿ.  ïåðâûå ÷àñû ðàáîòû âàðî÷íîé ïàíåëè âû ìîæåòå
ïî÷óâñòâîâàòü çàïàõ ææåíîé ðåçèíû. Ýòî íîðìàëüíîå ÿâëåíèå,
êîòîðîå áûñòðî ïðîïàäàåò.
27 Â ïðîöåññå ôóíêöèîíèðîâàíèÿ ãðèëÿ èëè äóõîâêè äîñòóïíûå
äåòàëè äóõîâîãî øêàôà ìîãóò ñèëüíî íàãðåòüñÿ. Íå
ðàçðåøàéòå äåòÿì ïðèáëèæàòüñÿ ê äóõîâîìó øêàôó.
28 Âñåãäà ïðîâåðÿéòå, ÷òîáû ðóêîÿòêè íàõîäèëèñü â ïîëîæåíèè /
o, êîãäà èçäåëèå íå èñïîëüçóåòñÿ;
29 Åñëè êóõîííàÿ ïëèòà óñòàíàâëèâàåòñÿ íà âîçâûøåíèå, íåîáõîäèìî
çàôèêñèðîâàòü åå íàäëåæàùèì îáðàçîì.
Äëÿ îáåñïå÷åíèÿ ýôôåêòèâíîñòè è áåçîïàñíîñòè äàííîãî èçäåëèÿ:
îáðàùàéòåñü òîëüêî â óïîëíîìî÷åííûå öåíòðû òåõíè÷åñêîãî îáñëóæèâàíèÿ
âñåãäå òðåáóéòå óñòàíîâêó îðèãèíàëüíûõ çàïàñíûõ ÷àñòåé
1 / 1

Whirlpool K6C10(W)/R Guida utente

Categoria
Forni
Tipo
Guida utente
Questo manuale è adatto anche per

in altre lingue