Ericsson DT292 Manuale utente

?

Cover Page Graphic

Place the graphic directly on the page, do not care about

putting it in the text flow. Select Graphics > Properties

and make the following settings:

• Width: 15,4 cm (Important!)

• Height: 11,2 cm (May be smaller)

• Top: 5,3 cm (Important!)

• Left: -0,3 cm (Important!)

This text should then be hidden.

DT292

Cordless Phone for MD110 Communication System

User Guide

DT2922

EN/LZT 103 70 R1A

3DT292

Table of Contents

Welcome ..........................................................4

Important .........................................................6

Description .....................................................12

Switching On/Off ............................................21

Free Seating (optional) ....................................22

Incoming Calls ...............................................23

Outgoing Calls ...............................................26

Phone Book ...................................................38

Call List ..........................................................46

During Calls ....................................................48

Call Forwarding ..............................................53

Absence Information (optional) .......................62

Messages ......................................................64

Group Features ..............................................68

Other Useful Features .....................................70

Settings ..........................................................75

Installation ......................................................86

Troubleshooting ..............................................92

Glossary .........................................................94

Index ..............................................................95

Welcome

DT2924

Welcome

Welcome to the user guide for the DT292 cordless phones in the

Ericsson MD110 communication system. It is a state-of-the-art

business communications system. Its alliance of features and

facilities effectively improves communications for virtually any kind

of organization.

There is a line of telephones designed for easy use in every

situation to take full advantage of these advanced features and

facilities.

Your phone is menu driven. By use of certain keys you get access

to frequently used functions and numbers, see section

“Description” on page 12.

Some markets use differing codes for some functions. In this guide,

all functions are described using the most common code.

The user guide describes the facilities of the DT292 cordless phone

as it is programmed at delivery from the factory. There may be

some differences in the way your phone is programmed. Please

consult your system administrator if you need further information.

The latest version of this user guide can also be downloaded from:

http://www.ericsson.com/enterprise/library/manuals.shtml.

If you would like to practise the handling of the phone, you can try

the “Ericsson Enterprise End User Training On Telephones”,

available at:

http://ericsson.tripnet.se/learngatestore/courses/EndUser/

Usertool/index.htm.

To start practising, select the option “Ericsson Enterprise

eLearning”, and then select your type of phone.

5DT292

Welcome

Copyright

stored in retrieval systems, or transmitted in any form or by any

means, electronic, mechanical, photocopying, recording or

otherwise, without prior written permission of the publisher except

in accordance with the following terms.

If this publication is made available on Ericsson´s homepage,

Ericsson gives its consent to downloading and printing copies of

the content provided in this file only for private use and not for

redistribution. No parts of this publication may be subject to

alteration, modification or commercial use. Ericsson will not be

liable for any damages arising from use of an illegal modified or

altered publication.

Warranty

ERICSSON MAKES NO WARRANTY OF ANY KIND WITH

REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED

TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. Ericsson shall not be

liable for errors contained herein nor for incidental or consequential

damages in connection with the furnishing, performance or use of

this material.

Declaration of Conformity

Hereby, Ericsson Enterprise AB, SE-131 89 Stockholm, declares

that this telephone is in conformity with the essential

requirements and other relevant provisions of the R&TTE

directive 1999/5/EC.

Details to be found at: http://www.ericsson.com/sdoc

Important

DT2926

Important

This section contains information that is important to know before

you start to use the DT292 phone and its functions.

Note: This user guide describes the supported MD110

communication system functions together with the most

commonly used phone-specific functions. All phone-specific

functions are listed in the menu structure, see section “Menu

structure” on page 20.

Preparing for use

Before using the DT292 the first time you have to charge and

connect the battery, see section “Preparing for use” on page 87.

Note: Place the DT292 in the charger and charge it for at

least 4 hours before using it the first time.

7DT292

Important

PIN code

Your phone is initially provided with a pre-set PIN code (Personal

Identification Number). You should change this PIN code to a

personal PIN code to prevent misuse.

To change the PIN code

Route: Settings » PhoneLock » ChangePIN

ChangePIN Select.

ÜÛ Press.

EnterOldPIN: is displayed.

Z ÜÛ Enter the current PIN code (default 0000) and press.

Either

EnterNewPIN: or Wrong PIN is displayed. In the latter

case, you have entered a number that does not match the current

PIN code.

Z ÜÛ Enter the four digits of the new PIN code and press.

RepeatNewPIN is displayed.

Z ÜÛ Enter the new PIN code again and press.

Either

New PIN accepted or Wrong New PIN is displayed.

Note the new PIN code for future use.

If you incorrectly enter a new PIN code three times in a row, your

phone leaves this menu option.

In other situations, if you enter an incorrect PIN code three times in

a row, your phone is blocked and

PIN Blocked, Unblock? is

displayed. See section “IPEI code” on page 8 to unblock your

phone.

Important

DT2928

IPEI code

If your phone is blocked because an incorrect PIN code has been

entered three times, you can unlock it with the IPEI code

(International Portable part Equipment Identity). After entering the

IPEI code, you must enter a new PIN code.

The IPEI code is a unique code which has been assigned to your

phone. The IPEI code can be found in the

ShowIPEI menu.

If your phone is blocked,

PIN Blocked, Unblock? appears. The

phone must be unblocked before it can be used again.

To display the IPEI code

Route: Information » ShowIPEI

ÜÛ Select ShowIPEI and press.

Enter PIN: is displayed.

Z ÜÛ Enter the PIN code for your phone (default 0000) and press.

The 13-digit IPEI code is displayed.

ÜÛ Press to leave this menu.

Note: Write down the IPEI code for future use. If you cannot

retrieve the IPEI code, please contact your system

administrator. Keep the IPEI code secret to prevent misuse

of your phone.

Unblock the DT292

ÜÛ Press.

Backdoor: is displayed.

Z ÜÛ Enter the IPEI code and press.

EnterNewPIN: is displayed.

Z ÜÛ Enter the four digits of the new PIN code and press.

RepeatNewPIN is displayed.

Z ÜÛ Enter the new PIN code again and press.

Either

New PIN accepted or Wrong New PIN is displayed. In the

latter case, the new PIN and the code you have just entered do not

match. If

New PIN accepted appears, you can use the phone

again.

9DT292

Important

Guidelines

Consider these suggestions and guidelines to keep your phone in

good shape and working properly.

Note: The phone does not contain user serviceable parts.

If your phone requires service you should return it to the

supplier or retailer from whom it was bought.

Intrinsic safety

The DT292 phone is not specified as intrinsically safe, so do not

use it in areas with a danger of explosion.

Treatment

• Avoid exposing in direct sunlight or close to other heat sources.

• Protect your phone from aggressive liquids and vapours.

• Keep the phone away from strong electromagnetic fields.

• Keep the phone away from moisture.

Battery handling

• Do not immerse the battery into water or throw into fire.

• Use the prescribed desktop charger for charging. Charge the

battery for at least one hour the first time you use the battery.

Cleaning

Clean the phone only with a soft, water dampened cloth. Using

soap or any other cleaning materials may discolor or damage the

phone.

Important

DT29210

Accessibility and voice quality

The base network is not always available. If you do not get in

contact with your system, contact your system administrator. For

best voice quality, avoid positioning near computer, radio or similar

euqipment.

Operating area

You can use your cordless telephone in the area that is covered by

the network. Outside this area you will lose contact with the

telephone network. The signal strength icon will disappear and

No

network will be displayed.

Out of coverage

When you leave the system's coverage area there will be a short

beep and a lamp indication.

When re-entering the coverage area it can take a couple of minutes

before the phone automatically has registered into the system.

11DT292

Important

Networks (menu option)

The menu option Networks should only be used for administration

purposes by service staff. Using this menu option may cause a

logout from the DECT/GAP network, and no further calls will be

possible.

Note: In case of a logout, the phone must be logged on

again by a service technician.

Description

DT29212

Description

2

1

3

4

5

6

8

7

9

10

11

12

13

14

15

16

17

18

Work 4711

07-Jul 11:32

19

13DT292

Description

1Volume Up

Off-hook: raise earpiece volume. See section “Settings” on page 75.

2Volume Down

Off-hook: lower earpiece volume. See section “Settings” on page 75.

3Off-hook / Yes

Answer call, accept.

4 Clear (C) / Mute

Delete latest entered digit. Backspace when editing text. Cancel a

menu option. Microphone, ringer and warning on/off, see sections

“During Calls” on page 48 and “Settings” on page 75.

5 Control key (up)

Scroll up through menus or name list. Move left through the

choices.

61 / Space

Space when editing text. See section “Phone Book” on page 38.

7 Battery (rear side)

See section “Installation” on page 86.

8 Star / Pause / Text case

Insert a dial tone pause. Upper/lower case in text mode. See

section “Phone Book” on page 38.

9Microphone

10 Warning light

Ringing, message waiting, battery low, exit cover area.

11 Earpiece

Please note: The phone may retain small magnetic

articles around the earpiece region.

12 Display (3 rows)

Display at rest. Work is the network name and 132 is (your)

extension number. See section “Display information” on page 16.

13 On/Off / On-hook / No

Switch on/off, end call, one menu back. Cancel a menu option.

14 Control key (down)

Scroll down through menus, name list. Move right in choices.

Description

DT29214

15 Keypad

16 Handsfree

Activate handsfree speaking. See sections “Incoming Calls” on

page 23, “Outgoing Calls” on page 26 and “During Calls” on

page 48.

17 R/Message

Put call on hold (inquiry), take call off hold or enter the message

system. See section “During Calls” on page 48.

18 Accessory connectors

See section “Installation” on page 86.

19 Loudspeaker (rear side)

For handsfree speaking function. See sections “Incoming Calls” on

page 23, “Outgoing Calls” on page 26 and “During Calls” on

page 48.

Phone signals

The cordless phone is signalling certain events audibly and visually

as described below.

The cordless phone also generates audible ring signals, alarm

signals and warning tones, and key clicks.

Signal Meaning

Red warning light Incoming call

Message waiting

Battery almost empty

Cordless phone out of range or not connected

Sound Meaning

Ring signal Incoming call

Alarm signal 4 short beeps every 30 seconds: battery almost

empty

4 short beeps every 2 minutes: Cordless phone

out of range or not connected

Key click You hear this each time you press a key (when

selected). See section “Key Sound” on page 81.

Warning tone You have pressed a key which has no function.

15DT292

Description

Ton e s

The following different tones are sent from the exchange to your

phone.

Tone characteristics

The tones shown in this section are the most used tones

worldwide. Many markets use a differing tone for one or more

situations.

Dial tone

Special dial tone

Ringing tone or queue tone

Busy tone

Congestion tone

Number unobtainable tone

Call waiting tone

Intrusion tone

Conference tone every 15 seconds (to all parties)

Verification tone

Warning tone, expensive route

Description

DT29216

Display information

The display gives you visual feedback on all actions that you

perform, and also textual warnings.

The upper two rows are text rows (12 possible characters in each

row), showing menus that you can access, names and numbers

that you edit or dial, your phone ID etc. The lower row displays

different statuses, visualized by icons.

The DT292 display:

The following display examples show the different states of your

phone.

Idle phone

Depending on the state and setting of your phone, different

information can be shown.

Normal:

Work is the programmed name of your network and can be

renamed to something more suitable, i.e. your first name, company

name, etc. To rename your network, contact your system

administrator. To the right of the display is your own extension

number.

Note: Date and time is only available for newer versions of

the exchange.

Follow-me activated:

The display shows your own extension number 4328 diverted to

extension number 4444.

Work 4328

16-Mar 10:22

4328 >

4444

17DT292

Description

Outgoing call

Normal outgoing call:

When you make an outgoing call, both the connection state and

the dialled number or name are displayed:

When the call is answered:

Diverted call:

If the dialled number is diverted, the diversion information is shown.

For example, the display shows the dialled number 3333 (Smith)

diverted to 4444 (Brown):

When the diverted call is answered, only the number of the

answering position is displayed:

Calling

3333

Calling

SMITH

3333

4444

> 3333

BROWN

> SMITH

4444

Description

DT29218

Incoming call

Normal incoming call:

If available, the number or the name of the caller is displayed. The

examples show an incoming call:

When you have answered the call, the caller's number is moved to

the right of the display.

Diverted call:

A diversion indicator in front of the number or the name tells you

that the call is diverted to your phone. For example, the display

shows that number 3333 (Smith) was dialled, but the call was

diverted to you:

When you have answered the call, the display shows only the

caller's number.

Signs in the text rows

> Menu pointer / Diversion indicator

Shows the menu that can be accessed by pressing the YES key.

When displayed before a name or number it indicates that the

phone is diverted to another extension.

< Number too long for display

There are more digits to the left.

Call list icon

Marks an entry in the Call list. Three different call types are

displayed:

<- Incoming call

-> Outgoing call

X Missed call

! Exclamation Mark

Marks an unread entry in an entry list.

3333 SMITH

>3333 >SMITH

19DT292

Description

Display icons

Signal strength

On when your phone is locked to the system. The bars indicate

reception quality. Four bars indicate optimal reception.

Ringer off

Ring signal muted or microphone off.

Key lock

Keys are locked.

Call

On when your phone is off-hook and flashes during ringing.

Message

Message received.

Call info

New unanswered entry in the MissedCalls list.

Battery gauge

The battery cells flash sequentially while the battery is charging and

remain solid when charging is complete. Indicates the amount of

talk and standby time left.

Note: An alarm sounds when there is less than 15 minutes

calling time left in the battery.

Additional display features

Depending on which network you are connected to, additional

display features are available. For example, displaying the date and

time. Ask your system administrator if you require additional display

features.

Description

DT29220

Menu structure

The available phone-specific functions and network functions can

be accessed via the DT292 menus.

L or M Press to access the on-hook menu when in idle state or to

access the off-hook menu during a call (see below).

Navigation keys

Menu Structure

AutoKeyLock

MasterReset

Language

Settings

Find&Call

*

DeleteAll

*

Options available when “on-hook”

SelectNet

Priority *

Rename

Delete

Subscribe

CallList *

MissedCalls *

LastCall *

TotalCalls

ShowIPEI

DevServices *

Store

Find&Edit *

Edit

Delete

AddNew

AddCallList

PhoneBook

Alerts

RingVolume

KeySound

DiscreetRng

RingType

Internal

External

CallBack

Message

PhoneLock

PowerOn

Subscript

ChangePIN

Display

Light

Contrast

Networks

**

Information

Find&Call

*

CallList *

GoToDTMF ***

DevServices *

Options available when “off-hook”

LM

Move within a menu.

ÜÛ Make selection.

Move to submenu.

ÚÙ Move to previous menu.

ë

Move to idle display.

* Available under certain conditions (e.g. entries stored).

Alarm

SetAlarm

AlarmOff *

Vibrator

OnIfSilent

On

Off

MessageKey

Mess.KeyNo

Voice: x Mailbox

Messages x

*

***Alternative menu DTMF-Long is not applicable for MD110.

Notes:

**Only to be used by system administrator

Left/Up

Right/Down

Confirm Back

Cancel

ÜÛ

ÚÙ

ë

M

L

La pagina sta caricando ...

Ericsson DT292 Manuale utente

Ericsson DT292 Manuale utente

in altre lingue

Documenti correlati

Altri documenti