Intermec PM4i Installation Instructions Manual

Installation

Instructions

EasyLAN Wireless

Interface Kit

(for EasyCoder PF2i,

PF4i, PF4ci, PM4i, PX4i,

and PX6i Printers)

Intermec Technologies Corporation

Corporate Headquarters

6001 36th Ave. W.

Everett, WA 98203

U.S.A.

www.intermec.com

 e information contained herein is proprietary and is provided solely for the

purpose of allowing customers to operate and service Intermec-manufactured

equipment and is not to be released, reproduced, or used for any other purpose

without written permission of Intermec.

Information and speciﬁ cations contained in this document are subject to

change without prior notice and do not represent a commitment on the part of

Intermec Technologies Corporation.

 e word Intermec, the Intermec logo, Norand, ArciTech, CrossBar, Data

Collection Browser, dcBrowser, Duratherm, EasyCoder, EasyLAN, Enterprise

Wireless LAN, EZBuilder, Fingerprint, i-gistics, INCA (under license), Inter-

Driver, Intermec Printer Network Manager, IRL, JANUS, LabelShop, Mobile

Framework, MobileLAN, Nor*Ware, Pen*Key, Precision Print, PrintSet, Route-

Power, TE 2000, Trakker Antares, UAP, Universal Access Point, and Virtual

Wedge are either trademarks or registered trademarks of Intermec Technologies

Corporation.

 roughout this manual, trademarked names may be used. Rather than put a

trademark (™ or ®) symbol in every occurrence of a trademarked name, we state

that we are using the names only in an editorial fashion, and to the beneﬁ t of

the trademark owner, with no intention of infringement.

 ere are U.S. and foreign patents pending.

Torx is a registered trademark of Camcar Division of Textron Inc.

 is product includes software developed by the OpenSSL Project for use in the

OpenSSL Toolkit (http://www.openssl.org/).

 is product includes cryptographic software written by Eric Young

([email protected]).

EasyLAN Wireless Interface Kit Installation Instructions iii

Contents

1

Introduction

About  ese Instructions ...............................................................2

Printer Firmware ............................................................................2

Installation Kit ...............................................................................2

Important 802MIG2 Information .................................................3

2

Physical Installation

Step-by-Step Instructions .............................................................14

3

EasyLAN Network Setup

EasyLAN Network Setup .............................................................24

Establishing Serial Communication .............................................24

Installing EasyLAN Network Setup ..............................................25

Starting EasyLAN Network Setup ................................................25

User and Password .......................................................................26

4

Setup in Fingerprint

Setting Up Wireless Communication ...........................................28

Reading Other Wireless Connection Variables .............................37

Reading Wireless Connection Setup .............................................40

Setting Up Network Parameters ...................................................40

Finishing the Setup ......................................................................42

5

Setup in IPL

Setting Up Wireless Communication ...........................................44

Reading Other Wireless Connection Variables .............................52

Finishing the Wireless Setup ........................................................54

Setting Up Network Parameters ...................................................55

6

Accessing the Printer’s Home Page

Using the Web Browser ................................................................62

iv EasyLAN Wireless Interface Kit Installation Instructions

Contents

EasyLAN Wireless Interface Kit Installation Instructions 1

 is chapter describes the EasyLAN Wireless interface

kit for EasyCoder PF2/4i-, PM4i-, and PX4/6i-series

printers. It also contains important information

regarding radio communication.

1

Introduction

2 EasyLAN Wireless Interface Kit Installation Instructions

Chapter 1 — Introduction

About These Instructions

 ese instructions describe how to install an EasyLAN Wireless network

interface in an EasyCoder PF2i, PF4i, PF4i Compact Industrial, PM4i,

PX4i, or PX6i printer and how to connect it to a LAN, WAN, Intranet,

or Internet network via a wireless connection.

 e installation instructions describe how to physically install the inter-

face board in a printer and how to set up the IP address, subnet mask,

default router, and name server.  e instructions end when you have

the printer’s home page up and running. From there, please refer to the

Intermec EasyLAN User’s Guide on the included CD-ROM.

 is interface kit must only be physically installed by an

authorized service technician.  e device is country/region

speciﬁ c and must be ordered for the correct country/region.

Use of this device in other region than shown on the device

home page/test label may violate applicable law.

Printer Firmware

For full functionality, your printer should either be ﬁ tted with Intermec

Fingerprint v8.40 (or later) or IPL v2.40 (or later). In Intermec Finger-

print, the network port is addressed as device "net1:" (communication

channel #5).

Installation Kit

 e EasyLAN Interface Kit contains:

• One EasyLAN adapter board complete with radio module ﬁ tted

• Rear plate (for EasyCoder PF2/4i-series printers only)

• RJ-45 plug (for EasyCoder PM4i and PX4/6i only)

• One light guide

• One hexagonal threaded spacer

• One antenna extension cable

• One antenna

• One cable clip

• One cable tie

• One CD-ROM with software and manuals

•  is Installation Instruction booklet

 e only tools required for the installation are #T10 and #T20 Torx

EasyLAN Wireless Interface Kit Installation Instructions 3

Chapter 1 — Introduction

Important 802MIG2 Information

For Users in the United States and Canada

 is device complies with Part 15 of the FCC Rules and with RSS-210

of Industry Canada. Operation is subject to the following two condi-

tions: (1)  is device may not cause harmful interference, and (2)  is

device must accept any interference received, including interference that

can cause undesired operation.

Federal Communications Commission Compliance

 is equipment is intended for operation in a commercial environment,

in compliance with the requirements for a Class B digital device, pursu-

ant to Part 15 of the FCC Rules, and it must not be used in a residential

environment. It generates, uses, and can radiate radio frequency energy.

If not installed and used in accordance with the instruction manual,

it may cause interference to radio communications. If this equipment

causes interference, the user will be required to correct the interference at

the user’s own expense.

Operation Warning:  e user shall stay at least 20 cm (8

in) away from the antenna of this device, when the device

is in use in access points and other hosts, where higher gain

antennas may be used.

Installation Warning: To comply with the FCC’s RF expo-

sure requirements and minimize health hazards:

Host devices with higher gain antennas such as access

points must be installed in such a way that the user will

be at least 20 cm (8 in) away from the antenna, when the

device is in use.

 e installers should not forget that the burden of main-

taining this distance is on the installer and not the user. the

antennas should be installed in a manner that will comply

with this requirement.

Changes or modiﬁ cations not expressly approved by

Intermec could void the user’s authority to operate this

equipment.

4 EasyLAN Wireless Interface Kit Installation Instructions

Chapter 1 — Introduction

Note: To maintain compliance with FCC Rules, the input/

output (I/O) cables that interconnect between the device and

any peripheral must be as speciﬁ ed by Intermec.

Industry Canada Compliance

 is Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

 is device requires a radio license, unless it is used totally inside a build-

ing. ( e user must obtain this license.)

Cet appareil numérique de la classe B respecte toutes les exigences du

Règlement sur le matériel brouilleur du Canada.

Cet appareil exige une license radio à moins d’être entièrement installé

dans un bâtiment. (L’utilisateur doit obtenir cette license.)

EasyLAN Wireless Interface Kit Installation Instructions 5

Chapter 1 — Introduction

For Users Outside of the United States and Canada

 e Intermec product you purchased contains a Mode 802MIG2 trans-

ceiver module.  is module transmits and receives data using a 2.4 GHz

Direct Sequence Spread Spectrum system.

Please check the Intermec web site for additional documentation at

www.intermec.com.

Hereby, Intermec Technologies Corporation declares that this Model

802MIG2 is in compliance with the essential requirements and other

relevant provisions of R&TTE Directive (1995/5/EC).  is product has

been assessed to the following standards:

• ETSI EN 300 328-2 v1.2.1 (2001-12)

• ETSI EN 301 489-17 v1.1.1 (2001-09)

• EN 60950:1992 (incl. Amdt. 1-4,11)

 e original Declaration of Conformity is available on the Intermec

Technologies Corporation web site at www.intermec.com.

 is product transmits electromagnetic waves at 2.4 GHz frequency

range. It has been tested and found compliant with U.S. (OET Guide

65) and Canadian (RSS 102) RF exposure regulations.  ere are no

regulations covering this product type in the European Union at this

time.

 e transmitter module’s output power is 11.6 mW.  e product using

this module are intended for business and industrial environments.  ey

should not be used in residential environments and by children.

 is product is marked with this logo and uses

radio frequency bands that are not harmonized

throughout the European Union.

6 EasyLAN Wireless Interface Kit Installation Instructions

Chapter 1 — Introduction

 e following table indicates the areas of intended use of the equipment

and any known restrictions.

Country of

Intended Use

Yes No License

Required

Restric-

tions

Details

Austria X

Belgium X

Denmark X

Finland X

France X X 2454 to 2483 MHz

bands must not be

used outdoors on this

device.

Germany X

Greece X

Ireland X

Italy X

Luxembourg X

 e Netherlands X

Portugal X

Slovenia X

Spain X

Sweden X

United Kingdom X

Other non-EU:

Iceland X

Liechtenstein X

Norway X

Switzerland X

Additional EMI/RFI Compliance

 is device meets the Class B limit requirements of CISPR 22.

EasyLAN Wireless Interface Kit Installation Instructions 7

Chapter 1 — Introduction

Pour les utilisateurs en dehors du Canada et des Etat-unis

Le produit Intermec que vous avez acheté contient un module émetteur-

récepteur de modèle 802MIG2. Ce module peut transmettre et recevoir

des données à l’aide d’un système d’étalement du spectre en séquence

directe de 2,4 GHz.

Pour obtenir toute documentation upplémentaire, veuillez consulter le

site web d’Intermec, à l’adresse www.intermec.com.

Par la présente, Intermec Technologies Corporation déclare que ce

modèle 802MIG2 est conforme aux exigences de base et autres exigen-

ces pertinentes de la Directive R&TTE (1999/5/EC). Ce produit a été

évalué par rapport aux normes suivantes :

• ETSI EN 300 328-2 v1.2.1 (2001-12)

• ETSI EN 301 489-17 v1.1.1 (2001-09)

• EN 60950:1992 (comprenant l’amendement 1-4, 11)

La Déclaration de conformité originale est disponible sur le site web

d’Intermec Technologies Corporation, à l’adresse www.intermec.com.

Ce produit émet des ondes électromagnétiques à une plage de fréquences

de 2,4 GHz. Il a été évalué et reconnu conforme aux règlements concer-

nant l’exposition à la radiofréquence des États-Unis (OET Guide 65) et

du Canada (RSS 102). Il n’y a actuellement aucun règlement couvrant ce

type de produit pour l’Union européenne.

La puissance de sortie du module émetteur-récepteur est de 11.6mW.

Les produits utilisant ce module sont destinés à des environnements

commerciaux et industriels. Ils ne doivent pas être utilisés dans des envi-

ronnements résidentiels et par des enfants.

Ce produit est marqué de ce logo et il utilise

des bandes de fréquence radio qui ne sont pas

harmonisées sur le territoire de la Communauté

européenne.

8 EasyLAN Wireless Interface Kit Installation Instructions

Chapter 1 — Introduction

Le tableau suivant répertorie les zones d’utilisation prévues pour l’équipe-

ment et les restrictions connues.

Pays d’utilisation

prévu

Oui Non License

Requise

Restric-

tions

Détails

France X X

Lorsque ce produit

est utilisé à

l’extérieur, il est alors

limité à une valeur

variant entre les

parties 2400 et 2454

MHz.

Conformité additionelle à la norme EMI/RFI

Cet appareil respecte les limites imposées pour la Classe B par le CISPR

22.

EasyLAN Wireless Interface Kit Installation Instructions 9

Chapter 1 — Introduction

Für Benutzer außerhalb von Kanada und den Vereinigten

Staaten

Das Intermec-Produkt, das Sie gekauft haben, enthält ein Sende-Emp-

fangs-Modul, Modell 802MIG2. Dieses Modul sendet und empfängt

Daten mit Hilfe eines 2,4-GHz-Direktsequenz-Spreiz-spektrumsystems.

Weitere Hinweise erhalten Sie auf der Intermec-website unter www.

intermec.com.

Hiermit erklärt Intermec Technologies Corporation, dass das Modell

802MIG2 mit den wesentlichen Anforderungen und anderen sachdien-

lichen Vorschriften der R&TTE-Richtlinie (1999/5/EC) übereinstimmt.

Dieses Produkt wurde gemäß der folgenden Normen bewertet:

• ETSI EN 300 328-2 v1.2.1 (2001-12)

• ETSI EN 301 489-17 v1.1.1 (2001-09)

• EN 60950:1992 (einschl. Amdt. 1-4, 11)

Die Originalkonformitätserklärung steht auf der website der Intermec

Technologies Corporation unter www.intermec.com zur Verfügung.

Dieses Produkt übermittelt elektromagnetische Wellen in einem

Frequenzbereich von 2,4 GHz. Es wurde getestet und in Überein-

stimmung mit U.S. (OET Anleitung 65) und kanadischen (RSS 102)

RF-Bestrahlungsvorschriften befunden. Zur Zeit gibt es in der EU keine

Richtlinien, die diesen Produkttyp abdecken.

Die Ausgangsleistung des Sende-Empfangs-Moduls beträgt 11.6mW. Die

Produkte, die dieses Modul verwenden, sind für geschäftliche und indu-

strielle Umgebungen gedacht. Sie sollten nicht in Wohngegenden und in

der Nähe von Kindern verwendet werden.

Das Produkt ist mit diesem Markenzeichen ver-

sehen und verwendet Radiofrequenzbreiten, die

in der Europäischen Gemeinschaft nicht überall

aufeinander abgestimmt sind.

Zusätzliche Elektromagnetische Störung-Übereinstimmung

Dieses Gerät entspricht den Grenzbestimmungen der Klasse B von

CISPR 22.

10 EasyLAN Wireless Interface Kit Installation Instructions

Chapter 1 — Introduction

Per gli utenti al di fuori del Canada o degli Stati Uniti

Il prodotto Intermec che avete acquistato contiene un modulo transcei-

ver Modello 802MIG2. Il transceiver trasmette e riceve i dati tramite

un sistema a 2,4 GHz che utilizza la tecnologia DSSS (sequenza diretta,

spettro esteso).

Per altre informazioni, consultate il sito web Intermec all’indirizzo www.

intermec.com.

Con la presente Intermec Technologies Corporation dichiara che questo

Modello 802MIG2 è conforme ai requisiti essenziali e alle altre clausole

importanti della direttiva R&TTE (1999/5/EC).

Questo prodotto è stato valutato in base ai seguenti standard:

• ETSI EN 300 328-2 v1.2.1 (2001-12)

• ETSI EN 301 489-17 v1.1.1 (2001-09)

• EN 60950:1992 (incluso Amdt. 1-4, 11)

La dichiarazione di conformità originale è disponibile presso il sito web

di Intermec Technologies Corporation a www.intermec.com.

Questo prodotto trasmette onde elettromagnetiche con una frequenza

intorno ai 2,4 GHz. Dai collaudi ai quali è stato sottoposto è risultato

conforme alle norme statunitensi (OET Guide 65) e a quelle canadesi

(RSS 102) relative all’esposizione alle radiofrequenze. Attualmente non

esistono norme relative a questo prodotto nell’Unione Europea.

La potenza di uscita del modulo trasmittente è di 11.6mW. I prodotti

che utilizzano questo modulo sono destinati ad ambienti industriali e

commerciali e non debbono essere utilizzati in ambienti residenziali e dai

bambini.

Questo prodotto reca questo marchio ed utilizza

bande di radiofrequnza che non sono armonizzate

nell’ambito della Comunità Europea.

Ulteriore conformità con EMI/RFI

Questo dispositivo è conforme ai limiti stabiliti in CISPR 22 per la

Classe B.

EasyLAN Wireless Interface Kit Installation Instructions 11

Chapter 1 — Introduction

Para Usuarios Fuera de Canada o de los Estados Unidos

Este producto de Intermec contiene un módulo transceptor Modelo

802MIG2. Dicho módulo transmite y recibe datos por medio de un

sistema de espectro ensanchado en secuencia directa de 2,4 GHz.

Para obtener documentación adicional, visite el sitio web de Intermec:

www.intermec.com.

Por la presente, Intermec Technologies Corporation declara que el

Modelo 802MIG2 cumple con los requisitos esenciales de acuerdo con

la directiva (1999/5/EC) de R&TTE. Este producto ha sido evaluado de

acuerdo con los siguientes estándares o normas:

• ETSI EN 300 328-2 v1.2.1 (2001-12)

• ETSI EN 301 489-17 v1.1.1 (2001-09)

• EN 60950:1992 (incl. Enmienda 1-4, 11)

La Declaración de Conformidad original está disponible en el sitio web

de Intermec Technologies Corporation: www.intermec.com.

Este producto transmite ondas electromagnéticas de radio en la gama

de frecuencias de 2,4 GHz. Ha sido probado y se ha determinado que

cumple con las reglamentaciones de los EE.UU. (OET Guide 65) y del

Canadá (RSS 102), referentes a la exposición de RF. En este momento,

no existen reglamentaciones que abarquen este producto en la UE.

La potencia de salida del módulo transmisor es de 11.6mW. Los pro-

ductos que usan este módulo están destinados para uso en ambientes

comerciales e industriales. No deben ser usados en ambientes residencia-

les o en la proximidad de niños.

Este producto está marcado con este logotipo y

usa bandas de frecuencia de radio que no han sido

armonizadas a lo largo de la Unión Europea.

Conformidad adicional con EMI/RFI

Este dispositivo cumple con los límites requeridos para la Clase B de

CISPR 22.

12 EasyLAN Wireless Interface Kit Installation Instructions

Chapter 1 — Introduction

Para Usuários Fora do Canadá ou dos Estados Unidos

O produto Intermec que você comprou contém um módulo transceptor

Modelo 802MIG2. Este módulo transmite e recebe dados usando um

sistema DSSS (Espectro de Difusão de Sequência Direta) de 2,4 GHz.

Consulte também o site da Intermec na web, no endereço www.intermec.

com, para documentação complementar.

Por este documento, a Intermec Technologies Corporation declara que

o Modelo 802MIG2 atende aos requisitos essenciais e outras condições

relevantes da Diretiva R&TTE (1999/5/EC). Esse produto foi avaliado

em relação aos seguintes padrões:

• ETSI EN 300 328-2 v1.2.1 (2001-12)

• ETSI EN 301 489-17 v1.1.1 (2001-09)

• EN 60950:1992 (incluída Amdt. 1-4, 11)

A Declaração de Conformidade original está disponível no site da web da

Intermec Technologies Corporation no endereço www.intermec.com.

Este produto transmite ondas eletromagnéticas na faixa de freqüência de

2,4 GHz. Ele foi testado e aprovado quanto à sua conformidade com os

regulamentos de exposição à RF dos EUA (OET Guide 65) e do Canadá

(RSS 102). Não existem regulamentos cobrindo esse tipo de produto atu-

almente na UE.

A potência de saída do módulo transmissor é de 11.6mW. Os produtos

que usam este módulo são destinados aos ambientes comerciais e indus-

triais. Eles não devem ser utilizados em ambientes residenciais e por

crianças.

Este produto é identiﬁ cado por esta logomarca e

utiliza bandas de freqüência de rádio que não estão

harmonizadas na Comunidade Européia.

Conformidades EMI/RFI Adicionais

Este produto atende aos requisitos de limite Classe B do CISPR 22.

EasyLAN Wireless Interface Kit Installation Instructions 13

2

Physical Installation

 is chapter describes how to physically install the

EasyLAN Wireless interface kit in a PF2/4i-, PM4i-,

or PX4/6i-series printer.

 e installation described in this chapter

must only be performed by an authorized

service technician. Intermec assumes

no responsibility for personal injury or

damage to the equipment if the instal-

lation in performed by an unauthorized

person.

Take precautions against electrostatic

discharges, for example by wearing

grounded bracelets.

Note: When the EasyLAN Wireless

interface is factory-installed in a printer,

the antenna is packed separately in the box

and must be ﬁ tted to its connector on the

printer’s rear plate as illustrated at the end

of this chapter.

14 EasyLAN Wireless Interface Kit Installation Instructions

Chapter 2 — Physical Installation

Step-by-Step Instructions

• Switch oﬀ the printer and disconnect the power cord.

• Disconnect all communication cables.

• Remove the cover over the electronics compartment as follows.

 e electronic compartment contains wires and compo-

nents with dangerous voltage (up to 380V). Make sure that

the printer is switched oﬀ and the power cord is discon-

nected before the left-hand cover is removed.

EasyCoder PF2/4i Printers

• Open the right-hand door.

• Using a #T20 Torx screwdriver, remove the three screws and lift the

cover up so it disengages the bottom plate.

• Swing out the rear part of the cover so you can disconnect the console

cable from the CPU board.

EasyLAN Wireless Interface Kit Installation Instructions 15

Chapter 2 — Physical Installation

• Put the cover aside on a soft cloth or similar to avoid scratches.

• Remove any optional interface board or blind cover plate ﬁ tted on the

rear plate.

• Remove any present EasyLAN Ethernet interface installed in the

printer including cables etc.

• Remove the present rear plate like this:

- Loosen but do not remove the two #T20 Torx screws that hold

the rear plate and the #T20 Torx screw that holds the rear bottom

corner of the CPU board.

- Carefully manipulate the rear plate out of the groove in the chassis.

Allow the CPU board to ﬂ ex a little to be able to get the connectors

out of their slots.

• Install the rear plate included in the kit in reverse order and tighten all

three screws.

• Reinstall any optional interface board or blind cover plate previously

removed.

• Continued on page 18.

16 EasyLAN Wireless Interface Kit Installation Instructions

Chapter 2 — Physical Installation

EasyCoder PM4i Printers

• Using a #T20 Torx screwdriver, loosen the four screws that holds the

cover along the lower left edge of the bottom plate.

• Remove the four screws that hold the cover to the center section.

• Pull out the cover so you can disconnect the console cable from the

CPU board.

• Put the cover aside on a soft cloth or similar to avoid scratches.

• Remove any present EasyLAN Ethernet interface including cables etc.

Fit the RJ-45 plug included in the kit into the square hole left by the

RJ-45 Ethernet connector.

• Remove the antenna plug, which is snap-locked into the rear plate.

• Continue on page 18.

La pagina sta caricando ...

Intermec PM4i Installation Instructions Manual

Questo manuale è adatto anche per

Intermec PM4i Installation Instructions Manual

in altre lingue

Documenti correlati

Altri documenti