Extron electronics SMK 2 Manuale utente

Marca
Extron electronics
Modello
SMK 2
Tipo
Manuale utente

Questo manuale è adatto anche per

1
IMPORTANT:
Go to www.extron.com for the
complete user guide and installation
instructions before connecting the
product to the power source.
www.extron.com
SMK 2 and SMK 3 • Installation Guide
Overview
ATTENTION:
• All structural steps and electrical installation must be performed by qualied personnel in accordance with local and
national building codes and electrical codes.
• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualié, conformément aux codes du
bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.
The SMK 2 is used to mount the TLP Pro 725M to a wall or glass surface. The
SMK 3 is used to mount the TLP Pro 1025M to a wall or glass surface.
This guide provides instructions for professional installers to mount and install
these touchpanels using the appropriate SMK mounting kit. The kits consist of:
A
(1) plastic enclosure (SMK 2 or SMK 3, see gure 1) with an adhesive patch
on the back.
B
The SMK 2 and SMK 3 Alignment Guide, which should be downloaded
from www.extron.com. Print at 100% size. Do not scale it.
C
(1) cover overlay.
The kit also includes the following optional items:
• (1) LED overlay (see figure 5,
5
, on the next page).
• (4) M3 screws (see figure 5,
6
).
• (1) 10 foot (3 meters) at Ethernet cable with RJ-45 connectors.
Cover
Overlay
SMK
A
lignment
Guide
Cover
Cover
O
verla
y
Page size: 11" x 17"
Print scale 1:1
Do not shrink.
1. See the E
xtro
n SMK 2
and SMK 3 Installation
Guide for complete
instructions.
2. Double-check the pr
int
settings
before printing.
Make sure the scale
settings
are 1:1.
3. After pr
inting, check that
the gr
ay dotted lines
correspond to the
dimensions shown.
4. Decide where to mount
the SMK.
Use this
template to ensure there
is enough
clearance at
the sides to mount the
touchpanel.
5. Stick this guide to the
glass
on the
opposite
side from where the
S
MK is being mounted
.
Use a level
to make sure
the template is horizont
al
.
6. Align the bottom edge of
the SMK (on the side
with the adhesive patch)
with the red line
o
n the
template. Wet the
adhesive patch so
that i
t
slides easily.
P
/N 68-3236-01
Rev.
B
Outer
edge of
TLP Pro 725M
5.05
"
H x 7.1"
W
(128 mm
H x 180 mm W)
Bottom, inner
edge
o
f SMK 2
Alignment Template for the Extron
SMK 2 and SMK 3
O
ut
er
edge of
TLP
Pro 1025M
6.84"
H x 10
.1" W
(174 m
m
H x 25
7 mm W)
S
MK
g
side fr
S
MK is bein
Use a level to ma
the template is horizo
e bottom ed
ge of
the SMK (o
n the side
with the a
with the a
with the a
with the a
with the a
with the a
h
dhesive pat
dhesive pat
dhesive pat
dhesive pat
dhesive pa
dhesive pa
dhesive
ch)
ch)
ch)
ch)
ch)
ch)
)
he
with the
with the r
with the r
with the r
with the r
with the r
with the r
with the r
with the r
line
on
ed line
on
ed line
on
ed line
on
ed line
on
ed line
on
ed line
on
ed line
on
ed line
on
ed line
on
th
the
the
the
the
the
the
the
the
the
template.
Wet the
adhesive p
atch so
tha
t i
t
slides easily.
P
/N 68-3236
-01
Rev.
B
C
A
B
Figure 1. SMK 2 or SMK 3 Kit
Before Starting
Remove one or more knockouts from the SMK enclosure to run cables
to the back of the touchpanel. The SMK has four knockouts (see
gure 2,
A
), one in the middle of each side.
You may need to use a sharp knife to cut the plastic holding the
knockout in place.
Option 1: Mounting the SMK to a Wall
with Fasteners
To mount the SMK to a wall or furniture:
1. Drill holes through the four dimples in the plastic (see gure 2,
B
).
2. Attach the SMK to the mounting surface, using screws (not
provided) that are appropriate for the mounting surface.
Do not overtighten the screws or the SMK may be damaged.
B
A
B
A
B
B
A
A
Figure 2. SMK Knockouts and Mounting Holes
1
Outside Glass Surface
2
3
3
Page size: 11" x 17"
Print scale 1:1
Do not shrink.
1. See the E
x
tron SMK 2
and SMK 3 Installation
Guide for complete
instructions
.
2. Double-check the pr
int
settings
before printing.
Make sure the
scale
settings
are 1:1.
3. After pr
inting, check that
the gr
ay dotted lines
correspon
d to the
dimensions shown.
4. Decide where to mount
the SMK.
Use this
template to ensure ther
e
is enough clearance at
the sides to mount the
touchpanel.
5. Stick this g
uide to the
glass
on the
o
pposite
side from where the
S
MK is being mounted
.
Use a lev
el
to make sure
the template is ho
rizont
al
.
6. Align the bottom edge of
the SMK (on the side
with the adhe
sive patch)
with the red line
on the
template. Wet the
adhesive patch so
that i
t
slides easily.
P
/N 68-3236-01
Rev.
B
Outer
edge of
TLP Pro 725
M
5.05"
H x 7.1
"
W
(128 mm
H x 180 mm W)
Alignment Template for the Extron
SMK 2 and SMK 3
O
ut
er
edge of
TLP Pro 1025M
6.84
"
H x 10
.1
"
W
(174 m
m
H x 25
7 mm W)
Inside Glass
Surface
O
utside
G
lass
S
urfac
e
3
Page size: 11
"
x 17
"
Print scale 1:1
Do not sh
rink.
1. See the
1. See the
E
x
tro
n SMK
E
x
tro
n SMK
E
x
tro
n SM
2
2
or the E
xtron
SMK 3
and SMK 3 Installation
and SMK 3 Installation
SMK 3
and SM
Installation
Guide fo
for
complete
instructio
io
ns.
2. Double-c
2.
heck the pr
he
int
settings
b
s
efore print
ef
ing.
Make sure
Ma
he
scale
th
ttings
a
sett
re 1
1:1.
3. After
er pr
inting,
, che
ck that
the gr
gr
ay d
otted
d lines
corres
spon
d
to t
the
dimens
sions
sho
own.
4. Decide
where to
o m
ount
the SMK
K.
U
se thi
is
template
e t
o ensu
ure th
er
e
is enoug
gh
cleara
ance a
t
the side
e
s
to mou
unt th
e
touchpa
anel
.
5. Stick th
h
is g
uide t
to
the
glass
o
on t
he
o
pp
pposite
side fro
rom
where
e the
S
MK is
is bei
ng m
mounted.
Use a
a leve
l
to m
make s
ure
the t
templa
te is
is ho
riz
ont
al
.
6. Alig
ign th
e bott
ottom ed
ge of
the
he SMK (o
n
n the side
w
with the a
d
dhesive pat
ch)
with the r
r
e
ed line
o
n
the
template
te.
Wet the
adhesiv
sive p
atch so
tha
t i
t
t
slides
es eas
ily.
P
/N 68-3236
-01
Rev.
B
Figure 3. Placing the Template
Option 2: Mounting the SMK to
a Glass Surface
1. Clean both sides of the glass with a lint-free cloth and a 1:1
mixture of isopropyl alcohol and water.
2. Place the alignment guide on the inside glass surface (see
gure 3,
1
).
Use tape (
2
) to attach the alignment guide to the glass. Use a
level (
3
) to ensure it is at the correct angle.
3. Remove the plastic backing from the adhesive patch on the back
of the SMK.
TIP: Wet your ngers to prevent them from sticking to the
adhesive patch.
gure 1
2
© 2018 - 2020 Extron Electronics All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
SMK 2 and SMK 3 • Installation Guide (Continued)
4. Hold the SMK at a slight angle with the top tilting forward and carefully
align the bottom inner edge of the SMK with the red line on the alignment
guide marked Bottom, inner edge of SMK (see gure 4,
1
).
5. Press the SMK rmly against the glass surface.
6. Remove the paper alignment guide.
Mounting the Cover Overlay (Optional)
The cover overlay (see figure 1,
C
, on the previous page) is not required for
mounting the touchpanel, but it can be applied to the inside glass surface
directly behind the SMK to improve the aesthetics when the SMK is viewed
through the window from inside the conference room.
1. Remove the paper backing from the cover overlay.
TIP: Wet your ngers to prevent them from sticking to the adhesive
patch.
2. Center the cover overlay behind the SMK enclosure.
TOP
Mounting Plate
LED Overlay
TLP Pr
o 725M
TLP Pro 7
2
TL
2
1
6
Back View
4
4
3
5
Figure 5. Mounting the TLP Pro 725M to the SMK 2
3. Use a credit card or similar at edge to remove any air
bubbles.
Mounting the Touchpanel
ATTENTION:
• Do not power on the touchpanels until you have
read the Attention in the Power supply section
of the TLP Pro 525, 725, and 1025 Series User
Guide.
• Ne branchez pas les écrans tactiles avant d’avoir
lu la mise en garde du TLP Pro 525, 725, et 1025
Series dans la section «sources d’alimentation»
du UserGuide.
Figure 5 shows how to mount the TLP Pro 725M to the
SMK 2. Mount the TLP Pro 1025M to the SMK 3 in exactly
the same way.
1. Remove the paper backing, and attach the LED overlay
to the back of the touchpanel (see gure 5,
1
). This
overlay covers the rear panel LEDs so that they do not
cause a distraction inside the conference room.
2. Run an Ethernet cable to the SMK and pass the cable
through the center of the mounting plate.
Pass the cable through the gap left by removing the
knockout (see Before Starting on the previous page).
3. Fasten the mounting plate to the SMK using the four
provided M3 screws (
2
). Use the holes marked EU on
the mounting plate.
4. Attach the Ethernet cable to the LAN/PoE input on the
rear panel of the touchpanel (see the TLP Pro 525, 725,
and 1025 Series User Guide).
5. The mounting plate has four hooks (
3
), one on each
corner. Position the touchpanel so that these hooks t
into the four slots on the rear panel of the touchpanel
(see the TLP Pro 525, 725, and 1025 Series User
Guide).
6. Slide the touchpanel down slightly so that the hooks
are seated securely in the slots.
7. The tongue at the bottom of the mounting plate (
4
)
sits in the groove in the bottom of the touchpanel (see
inset,
5
). Fasten the touchpanel to the mounting plate
by tightening the lock screw (
6
).
Page size: 11" x 17"
Print scale 1:1
Do not shrink.
1. See the Extron SMK 2
and SMK 3 Installation
Guide for complete
instructions.
2. Double-check the print
settings before printing.
Make sure the scale
settings are 1:1.
3. After printing, check that
the gray dotted lines
correspond to the
dimensions shown.
4. Decide where to mount
the SMK. Use this
template to ensure there
is enough clearance at
the sides to mount the
touchpanel.
5. Stick this guide to the
glass on the opposite
side from where the
SMK is being mounted.
Use a level to make sure
the template is horizontal.
6. Align the bottom edge of
the SMK (on the side
with the adhesive pa
tch)
with the red line on the
template. Wet the
adhesive patch so that it
slides easily.
P/N 68-3236-01 Rev. B
Bottom, inner
edge of SMK 2
Alignment Template for the Extron
SMK 2 and SMK 3
Outer edge of
TLP Pro 1025M
6.84" H x 10.1" W
(174 mm H x 257 mm W)
Page size: 11
"
x 17
"
Print scale 1:1
Do not shrink.
1. See the Extron SMK 2
and SMK 3 Installation
Guide for complete
instructions.
2. Double-check the print
settings before printing.
Make sure the scale
settings are 1:1.
3. After printing, check that
the gray dotted lines
correspond to the
dimensions shown.
4. Decide where to mount
the SMK. Use this
template to ensure there
is enough clearance at
the sides to mount the
touchpanel.
5. Stick this guide to the
glass on th
e opposite
de from w
here the
s bein
g mounted.
ed.
evel
to make s
e sur
e
mplat
e is hor
horizon
tal.
he
bottom
ottom edge
of
MK (on
(on
the side
e a
e ad
hesive patch
)
e re
d line on th
e
ate. W
et the
ve pa
tch so that
it
easi
ly.
N 68-3236-01 Rev. B
Bottom, inner
edge of SMK 2
Alignment Template for the Extron
SMK 2 and SMK 3
Outer edge of
TLP Pro 1025M
6.84
"
H x 10.1
"
W
(174 mm H x 257 mm W)
1
g
side fr
sid
s
s
K is
MK
MK
MK
MK
SMK
MK
SMK
MK
SM
MK
SM
SM
SM
SM
e
e
a
a le
e
a
s
se
s
Us
th
he
e
e
e
t
t
te
te
em
6. Al
l
i
g
g
g
gn
n
n
n th
th
he
e
e
e
S
S
S
S
SM
wi
i
it
th
h
h
h
h
t
the
wi
i
it
th
h
h
h
h
t
the
he
te
em
m
m
m
m
p
p
plat
p
p
p
m
m
m
m
e
a
h
he
e
e
e
esiv
h
d
d
ad
sl
i
id
d
d
de
e
e
es
es e
P
P/N
Figure 4. Attaching the SMK to the Glass
gure 5
68-3233-01 Rev. D
01 20
  • Page 1 1
  • Page 2 2

Extron electronics SMK 2 Manuale utente

Marca
Extron electronics
Modello
SMK 2
Tipo
Manuale utente
Questo manuale è adatto anche per
Scarica PDF
rapporto

in altre lingue

Altri documenti