Toto WH171A Installation Instructions Manual
- Categoria
- Prodotti sanitari
- Tipo
- Installation Instructions Manual
Questo manuale è adatto anche per
WH171B(系列)
WH172B(系列)
WH171A
WH172A
WH171B(SERIES)
WH172B(SERIES)
WH171A
WH172A
563403
2018.4
Middle East Branch LOB19-1701-1702, Jebel Ali Free Zone, P.O. box 261804, Dubai U.A.E.
Manila Representative Office. Unit 1010, 10th Floor Rufino Building, Ayala Avenue cor.V.A.
/
77 Moo 5 HSIL Industrial Zone T.Nong -Plamor A.Nong-Khae Saraburi 18140 Thailand
2
Note:
ၢ༶ѝ۳֬֬য়١ٌᇖႼሆଃƓᆓؚႯ߃Ɣ֬ƗႯ߃ढ़ၢҜᅽሸྡྷࢺबèݛࢺब҉ਛƗ໊࣓ࣣᆾ
֬٫ሌ၃ಭ൝࣐ྡྷሸྡྷҾࢺދໂྰƗྺࠪ൏৺༩པ႒֬ሌ၃ಭ൝ࢺबƗь૮ছսߋࠎӈഺ҉шး֬ગٗ
ދ෬è
Users may fix the problems on their own if the corrective action is to be taken by the user according to the chart below.
Non-professionals are prohibited from disassembling and repairing the product. Please contact the relevant professionals
for futher troubleshooting to avoid aggravating the problem.
ӏࡵܪᅷ
ඪམٌ࣐ඪ
ඪམႼඪ҉ؕ
ੇ֥છৡ
ჷႀ য়١ٌ
ç್߃ቀ࣐ඪቀً໊ाచࠎ๛ඪè
çඪམ࣐ඪً໊࢟ռाè
ç࣐ඪًڣႼၺ༅़ህࠎ࣐ඪًԵܙ
ࡸൗ֫ڣٌᆥӏ༶è
çԩၢഏჷႀƗ၎ಝٌ࣐ඪè
çඪམԢඪ८çඪֿًቝᇢຽႼၺ༅
Ɠజు൏҉ཱིྖל࣐ಇ֬ࢄç്ཱིॽ
ְƔƗᄶӵඪًٌޚށ֬૨хè
çϷןࢲઋۍບҍٺӐƗϷሔഏ
ޱᄶӵඪًᆿඪܬᄤଝ၉໑ᇉ
ഏƗٌ૨хè
çᄤඪམৡ֬ϷןࢲઋۍӐƗ֥
ඪམୄҍ֬ѐᆵܼࠎఊඪམམ฿ഏƗ
Ⴜ൏ٌ߽ߴ໑è
çռा࣐ඪቀًࠎ৺༩༅၃ࢺब
ƓᆓؚႯ߃Ɣ
çռाඪམ࣐ඪً࢟
Ɠᆓؚሌ၃ಭ჻Ɣ
çࡦҷ࣐ඪًѰԩၺ༅
Ɠᆓؚሌ၃ಭ჻Ɣè
ç۾ߗ࣐ඪً
Ɠᆓؚሌ၃ಭ჻Ɣè
ç౩য়ඪམୄҍ֬ၺ༅
Ɠᆓؚሌ၃ಭ჻Ɣè
çןᆣϷןࢲઋۍ֬໑ᇉ
Ɠᆓؚሌ၃ಭ჻è
çؒןࢲઋۍ
Ɠᆓؚሌ၃ಭ჻Ɣè
Common faults
Water does not
flow into the tank
Water is
constantly
running into
the bowl.
Possible causes Corrective actions
1 Household water supply has not been turned
on or has been cut off.
2. Angle valve has not been turned on.
3. Residuums in the inlet valve causing the float
device to not operate properly.
4. None of the above.
1. Flush valve seal is not completely closed due
to residuums around the outlet of the cistern
and flush valve (sand or debris lodged in
during installation).
2. The exposed part of the panel's adjust screw
is too long, which resulting the rubber of flush
valve can not fixed in a certain position and
can not sealed.
3. The part of panel's adjusting screw in the
cistern is too long, which may get stuck in the
soft pipe or cistern body and unable to return
sometimes.
1. Turn on the household water supply or
contact the relevant personnel (To be
done by the user).
2. Turn on the angle valve
(To be done by professionals only).
3. Check the fill valve and remove the
residuum To be done by
professionals only).
4. Change the inlet valve
To be done by professionals only .
1. Remove the residuums in the cistern
(To be done by professionals only).
2. Adjust the position of the panel's screw
(To be done by professionals only).
3. To cut back the adjust screw
(To be done by professionals only).
ၥܪᅷؕࠪয়١ٌ
Self diagnosis and troubleshooting
1
Important:
Caution:
Neglecting this sign may result in misunderstanding of the installation instructions, which can
lead to injuries or damage to property.
ѝ൜ݛ൱Օњᇄؾշ༉য়ࢺçҧቛ൏ढ़نഺ༉ࢺçູݤಭ฿ࠪ෬ߑ༅֬ൠࡸè
൴ႌҦ൛ඪམ܆ƥ࿀ඪç࣐ඪًಿఝçъܲ൛ѓఝᆭࡖƗൗႯ܆฿ཊᄤ൴ႌҦ൛ඪམ܄ቛϷ
නଃඇᇖƦ
Օනଃඇᇁ܉൴ႌҦ൛ඪམτሔཔܸୄಿè
ᄤϖս৭׀౼τሔ൏౯ቕ);6B;༩ਠњሠࠎᆇ֙׀њሠ
ç౯ൗႯ౩ඪࠎ༕൫֬ᇖྦ౩ࢸ࠻Ɠ༨ࢸְ࣡Ɣҏൡދ౩ࢸඪམϷƗ؋मႯڱྦృ֬౩ࢸ࠻Ɠƥಇ
ٿçਟ༕൫࠻çЭְƔࠎ๔ර࣐ྡྷҏൡƗၢ૮ڱѰ௬ߑϷ֬ૌܻè
Use water or dilute mild detergent (such as dishwashing detergent) to scrub and clean the surface, Never use strong
corrosive detergent (such as cleanser, paint thinner, benzene and so on) or wire ball to scrub, and to avoid corroding
the surface of the product.
çݛྺးٳఠЮӈƗ౯༆ࢃఊቛເ၉ϵഺࠊঞࠔয়Ɨ౯၎ᅽٌ݆ࣣႵ؆৲֬ߴ൳฿༩࣐ྡྷލ൨֬
য়ç߲ڶދߴ൳è
Please dispose of this product in accordance to the local waste disposal laws and regulations.
1. Functions of the manual concealed cistern: storage water, inlet and outlet calve vessel, frame of wall-hung toilet,
The function reflected in the manual actuator panel instructions.
2. This instruction manual only supports the installation of the manual concealed cistern.
3. For Australia, the installation has to be in accordance with AS/NZS 3500 series of Standards and/or local standards.
ሆၰൠརCautions
౩ࢸçٳ༅য়
Cleaning and waste disposal
2
Note:
ၢ༶ѝ۳֬֬য়١ٌᇖႼሆଃƓᆓؚႯ߃Ɣ֬ƗႯ߃ढ़ၢҜᅽሸྡྷࢺबèݛࢺब҉ਛƗ໊࣓ࣣᆾ
֬٫ሌ၃ಭ൝࣐ྡྷሸྡྷҾࢺދໂྰƗྺࠪ൏৺༩པ႒֬ሌ၃ಭ൝ࢺबƗь૮ছսߋࠎӈഺ҉шး֬ગٗ
ދ෬è
Users may fix the problems on their own if the corrective action is to be taken by the user according to the chart below.
Non-professionals are prohibited from disassembling and repairing the product. Please contact the relevant professionals
for futher troubleshooting to avoid aggravating the problem.
ӏࡵܪᅷ
ඪམٌ࣐ඪ
ඪམႼඪ҉ؕ
ੇ֥છৡ
ჷႀ য়١ٌ
ç್߃ቀ࣐ඪቀً໊ाచࠎ๛ඪè
çඪམ࣐ඪً໊࢟ռाè
ç࣐ඪًڣႼၺ༅़ህࠎ࣐ඪًԵܙ
ࡸൗ֫ڣٌᆥӏ༶è
çԩၢഏჷႀƗ၎ಝٌ࣐ඪè
çඪམԢඪ८çඪֿًቝᇢຽႼၺ༅
Ɠజు൏҉ཱིྖל࣐ಇ֬ࢄç്ཱིॽ
ְƔƗᄶӵඪًٌޚށ֬૨хè
çϷןࢲઋۍບҍٺӐƗϷሔഏ
ޱᄶӵඪًᆿඪܬᄤଝ၉໑ᇉ
ഏƗٌ૨хè
çᄤඪམৡ֬ϷןࢲઋۍӐƗ֥
ඪམୄҍ֬ѐᆵܼࠎఊඪམམ฿ഏƗ
Ⴜ൏ٌ߽ߴ໑è
çռा࣐ඪቀًࠎ৺༩༅၃ࢺब
ƓᆓؚႯ߃Ɣ
çռाඪམ࣐ඪً࢟
Ɠᆓؚሌ၃ಭ჻Ɣ
çࡦҷ࣐ඪًѰԩၺ༅
Ɠᆓؚሌ၃ಭ჻Ɣè
ç۾ߗ࣐ඪً
Ɠᆓؚሌ၃ಭ჻Ɣè
ç౩য়ඪམୄҍ֬ၺ༅
Ɠᆓؚሌ၃ಭ჻Ɣè
çןᆣϷןࢲઋۍ֬໑ᇉ
Ɠᆓؚሌ၃ಭ჻è
çؒןࢲઋۍ
Ɠᆓؚሌ၃ಭ჻Ɣè
Common faults
Water does not
flow into the tank
Water is
constantly
running into
the bowl.
Possible causes Corrective actions
1 Household water supply has not been turned
on or has been cut off.
2. Angle valve has not been turned on.
3. Residuums in the inlet valve causing the float
device to not operate properly.
4. None of the above.
1. Flush valve seal is not completely closed due
to residuums around the outlet of the cistern
and flush valve (sand or debris lodged in
during installation).
2. The exposed part of the panel's adjust screw
is too long, which resulting the rubber of flush
valve can not fixed in a certain position and
can not sealed.
3. The part of panel's adjusting screw in the
cistern is too long, which may get stuck in the
soft pipe or cistern body and unable to return
sometimes.
1. Turn on the household water supply or
contact the relevant personnel (To be
done by the user).
2. Turn on the angle valve
(To be done by professionals only).
3. Check the fill valve and remove the
residuum To be done by
professionals only).
4. Change the inlet valve
To be done by professionals only .
1. Remove the residuums in the cistern
(To be done by professionals only).
2. Adjust the position of the panel's screw
(To be done by professionals only).
3. To cut back the adjust screw
(To be done by professionals only).
ၥܪᅷؕࠪয়١ٌ
Self diagnosis and troubleshooting
1
Important:
Caution:
Neglecting this sign may result in misunderstanding of the installation instructions, which can
lead to injuries or damage to property.
ѝ൜ݛ൱Օњᇄؾշ༉য়ࢺçҧቛ൏ढ़نഺ༉ࢺçູݤಭ฿ࠪ෬ߑ༅֬ൠࡸè
൴ႌҦ൛ඪམ܆ƥ࿀ඪç࣐ඪًಿఝçъܲ൛ѓఝᆭࡖƗൗႯ܆฿ཊᄤ൴ႌҦ൛ඪམ܄ቛϷ
නଃඇᇖƦ
Օනଃඇᇁ܉൴ႌҦ൛ඪམτሔཔܸୄಿè
ᄤϖս৭׀౼τሔ൏౯ቕ);6B;༩ਠњሠࠎᆇ֙׀њሠ
ç౯ൗႯ౩ඪࠎ༕൫֬ᇖྦ౩ࢸ࠻Ɠ༨ࢸְ࣡Ɣҏൡދ౩ࢸඪམϷƗ؋मႯڱྦృ֬౩ࢸ࠻Ɠƥಇ
ٿçਟ༕൫࠻çЭְƔࠎ๔ර࣐ྡྷҏൡƗၢ૮ڱѰ௬ߑϷ֬ૌܻè
Use water or dilute mild detergent (such as dishwashing detergent) to scrub and clean the surface, Never use strong
corrosive detergent (such as cleanser, paint thinner, benzene and so on) or wire ball to scrub, and to avoid corroding
the surface of the product.
çݛྺးٳఠЮӈƗ౯༆ࢃఊቛເ၉ϵഺࠊঞࠔয়Ɨ౯၎ᅽٌ݆ࣣႵ؆৲֬ߴ൳฿༩࣐ྡྷލ൨֬
য়ç߲ڶދߴ൳è
Please dispose of this product in accordance to the local waste disposal laws and regulations.
1. Functions of the manual concealed cistern: storage water, inlet and outlet calve vessel, frame of wall-hung toilet,
The function reflected in the manual actuator panel instructions.
2. This instruction manual only supports the installation of the manual concealed cistern.
3. For Australia, the installation has to be in accordance with AS/NZS 3500 series of Standards and/or local standards.
ሆၰൠརCautions
౩ࢸçٳ༅য়
Cleaning and waste disposal
3
Important:
τሔఴ౯ሴ༬ᄎ؇නଃඇƗЮ܋ය҉Ӽႀτሔ
ಭ჻໊φනଃඇး౷േ܄ᄶӵ֬෬ӈᇖЎ
ݪೕ߈࠻Ɨτሔѓఝ൏࿑Ⴏ
1. Please read through this Instructions carefully prior to
installation,and our company shall not be responsible
for any loss caused by not installating according with
this Instructions. Lubricants are provided for the
installation.
ᄤᆭࡖτሔఴƗ႒༼ಙಱτሔ໑ᇉƗѰۻओ൰ୄሔ
ྰ֬ቀ฿ҭߊಙሔྰຢӵޱ֬׀..4ᄤτሔ
ుഏߊԢ..4ནƗѰ൚ᇛၢՕቛເۡ؎֬ࠕሠན
2. Please confirm the FFL according to the overall indoor
fitment method. Line out the FFL on the wall and
always regard FFL as datum line of 0 height.
ᄤτሔᆭࡖఴƗ౯ಙಱτሔుъӼᇞ
ుƗుъޯ؎ᄤ UUၢഏƗౖ֙SONၢ
ഏ֬৶േࡍຢ܄ޱ֬ѓఝఴؑ൏Ɨుъ႒
Ӽൺᆊܩট৶è
3. Please confirm the wall is the main wall, the
thickness exceed 80mm and it can bear more
than 300kgf strength when the strength act on
the front of toilet bowl.
౯ᄤ๓ՓልఴτሔЮӈƦႼ֬ԋձ֍໑
ເݿૣ
൜ਲ਼ࡸೖთ༅҉ڟƗ౯ၢ༅ເሠ
1. Please install the frame before paving the tiles.
The dimensional unit is millimeter.
2. As the parts images are for illustrative
purposes only, please refer to the actual
product if it varies from the parts images.
Note:
FFL =
0
FFL of finish face, all dimension is
millimeter
FFL =
0
FFL
0
B
A
300kgf
τሔනଃ
INSTALLATION INSTRUCTION FOR MANUAL CONCEALED CISTERN
ࡸ၉লѝ"
Accessories List:
Main wall
Straight flush pipe of some products are offered with two kinds of
seal gaskets A.B which can be selected according to toilet bowl
type during installation.
4
ሴ༬ࡦҷƗಙГЎሔᇖ֬ࡸƥ
Check to make sure you have all these parts from the package:
Parts in Bag 2
Ўሔᇖ֬ࡸ
Parts in Bag 44
Ўሔᇖ֬ࡸ Parts in Bag 3
ుୄඪམƓຈࡖƔ
In Wall Tank (Carrier)
ઋໜᇿ
Threaded
Mounting Stud (2)
ઋໜᇿ
Threaded
Mounting Stud (2)
༶ᆭࡖ
Lower
Bracket
ᅵೝ
Anchor (6)
ઋ
Lag Screw (6)
ઋඤ
Bolt (4)
ు࢝ܬॽ
Angle Fixture
࣐ඪً࢟
Angle Valve
ઋඤ
Bolt (4)
ઋଢ
Nut (4)
ઋଢ
Nut (2)
ۉሷ
Cap (2)
Washer (2)
ᇿઋඤٌম
Stud Bolt Flange (2)
ٌমܼ
Flange Pipe
࣐ඪܼ
Inlet Pipe
ೕ߈ݡ૬
Lubricated Sponge
૨چั*
Seal Gasket B
૨چั)
Seal Gasket A
ხϷ
Push Plate Rough In
ხϷ
Push Plate Rough In
τሔනଃඇ
Installation
Manual
Ўሔᇖ֬ࡸ Parts in Bag 1
ඪܼ
֚؈
Outlet Pipe
Mud Guard
࣐ඪܼ
֚؈
Inlet Pipe
Mud Guard
ඪܼ
Outlet Pipe
ഏᆭࡖ
Upper Bracket
ЎሔಙಱIncluded Parts
3
Important:
τሔఴ౯ሴ༬ᄎ؇නଃඇƗЮ܋ය҉Ӽႀτሔ
ಭ჻໊φනଃඇး౷േ܄ᄶӵ֬෬ӈᇖЎ
ݪೕ߈࠻Ɨτሔѓఝ൏࿑Ⴏ
1. Please read through this Instructions carefully prior to
installation,and our company shall not be responsible
for any loss caused by not installating according with
this Instructions. Lubricants are provided for the
installation.
ᄤᆭࡖτሔఴƗ႒༼ಙಱτሔ໑ᇉƗѰۻओ൰ୄሔ
ྰ֬ቀ฿ҭߊಙሔྰຢӵޱ֬׀..4ᄤτሔ
ుഏߊԢ..4ནƗѰ൚ᇛၢՕቛເۡ؎֬ࠕሠན
2. Please confirm the FFL according to the overall indoor
fitment method. Line out the FFL on the wall and
always regard FFL as datum line of 0 height.
ᄤτሔᆭࡖఴƗ౯ಙಱτሔుъӼᇞ
ుƗుъޯ؎ᄤ UUၢഏƗౖ֙SONၢ
ഏ֬৶േࡍຢ܄ޱ֬ѓఝఴؑ൏Ɨుъ႒
Ӽൺᆊܩট৶è
3. Please confirm the wall is the main wall, the
thickness exceed 80mm and it can bear more
than 300kgf strength when the strength act on
the front of toilet bowl.
౯ᄤ๓ՓልఴτሔЮӈƦႼ֬ԋձ֍໑
ເݿૣ
൜ਲ਼ࡸೖთ༅҉ڟƗ౯ၢ༅ເሠ
1. Please install the frame before paving the tiles.
The dimensional unit is millimeter.
2. As the parts images are for illustrative
purposes only, please refer to the actual
product if it varies from the parts images.
Note:
FFL =
0
FFL of finish face, all dimension is
millimeter
FFL =
0
FFL
0
B
A
300kgf
τሔනଃ
INSTALLATION INSTRUCTION FOR MANUAL CONCEALED CISTERN
ࡸ၉লѝ"
Accessories List:
Main wall
Straight flush pipe of some products are offered with two kinds of
seal gaskets A.B which can be selected according to toilet bowl
type during installation.
4
ሴ༬ࡦҷƗಙГЎሔᇖ֬ࡸƥ
Check to make sure you have all these parts from the package:
Parts in Bag 2
Ўሔᇖ֬ࡸ
Parts in Bag 44
Ўሔᇖ֬ࡸ Parts in Bag 3
ుୄඪམƓຈࡖƔ
In Wall Tank (Carrier)
ઋໜᇿ
Threaded
Mounting Stud (2)
ઋໜᇿ
Threaded
Mounting Stud (2)
༶ᆭࡖ
Lower
Bracket
ᅵೝ
Anchor (6)
ઋ
Lag Screw (6)
ઋඤ
Bolt (4)
ు࢝ܬॽ
Angle Fixture
࣐ඪً࢟
Angle Valve
ઋඤ
Bolt (4)
ઋଢ
Nut (4)
ઋଢ
Nut (2)
ۉሷ
Cap (2)
Washer (2)
ᇿઋඤٌম
Stud Bolt Flange (2)
ٌমܼ
Flange Pipe
࣐ඪܼ
Inlet Pipe
ೕ߈ݡ૬
Lubricated Sponge
૨چั*
Seal Gasket B
૨چั)
Seal Gasket A
ხϷ
Push Plate Rough In
ხϷ
Push Plate Rough In
τሔනଃඇ
Installation
Manual
Ўሔᇖ֬ࡸ Parts in Bag 1
ඪܼ
֚؈
Outlet Pipe
Mud Guard
࣐ඪܼ
֚؈
Inlet Pipe
Mud Guard
ඪܼ
Outlet Pipe
ഏᆭࡖ
Upper Bracket
ЎሔಙಱIncluded Parts
110/130
位置1 Position1: 65 (A档)/W=85 (B档)
位置2 Position2: W=110 (A档)/130 (B档)
45°，
The drainage function may be affected when the installation
排污管侧向45度输出时，只能装在位置2(W=110/130)
When excretory tube lean 45°, it can only be fixed in
必要时，根据马桶尺寸调整管夹和排污管位置。
If necessary, adjust the clamp and drainage pipe location
(Clamp should only be untightened by professionals!)
位置2
Position 2
位置1
Position 1
B
A
152 134
6
W 110/130
Note: The drainage function may be affected when the installation
angle of drainage pipe exceed 45°
When excretory tube lean 45°, it can only be fixed in
Position 2(W=80/100).
If necessary, adjust the clamp and drainage pipe location
according to the bowl dimension.
(Clamp should only be untightened by professionals!)
Install drainage pipe clamp.
Position 2
Position 1
B
B
A
A
5
580
1000
650
40
G1/2
1110
1180
180
230
320
100
35
FFL
0
35(15~135)
147 129
0
110
Main wall
Main wall
135~220
20~60
400-10
0
110
W(70~130)
Please make sure W is between 70 to 130.
Dimensions and Supply Pipe-laying
Drainage Pipe Installation
8
1
1
2
1
19
2
3
“Click”
“Click”
1
2
3
B
B
AA
“Click’’“Click’’
“Click’’“Click’’
Adjust horizontally and vertically, and tighten lag screw:
B
C
D
E
A
7
2.
1.
10mm
10X50mm
1
3
2
4
5
6
1165
0
FFL
490
286
650
C
B
A
C
A
B
A
ҋᇮනଃƥ
५@മƦ
ሔ್ᅵઋඤƦ
As shown on picture:
1. Drill 10*60;
2. Insert anchor;
Drill on the main wall and floor
Install Wall-fixing bracket and adjust floor-fixing bracket
䃦
Install Expansion Bolts
0
0
䃦䠘൏ઋඤӐ؎ເUU
䃦䠘170: Bolt length of 75 mm
䃦䍻൏ઋඤӐ؎ເUU
䃦䍻170: Bolt length of 120 mm
0
8
1
1
2
1
19
2
3
“Click”
“Click”
1
2
3
B
B
AA
“Click’’“Click’’
“Click’’“Click’’
Adjust horizontally and vertically, and tighten lag screw:
B
C
D
E
A
7
2.
1.
10mm
10X50mm
1
3
2
4
5
6
1165
0
FFL
490
286
650
C
B
A
C
A
B
A
ҋᇮනଃƥ
५@മƦ
ሔ್ᅵઋඤƦ
As shown on picture:
1. Drill 10*60;
2. Insert anchor;
Drill on the main wall and floor
Install Wall-fixing bracket and adjust floor-fixing bracket
䃦
Install Expansion Bolts
0
0
䃦䠘൏ઋඤӐ؎ເUU
䃦䠘170: Bolt length of 75 mm
䃦䍻൏ઋඤӐ؎ເUU
䃦䍻170: Bolt length of 120 mm
0
10
The thickness of fixed wall is 20~60mm
(measured from the front of frame to the finished tile surface)
ሆƥ
ሔྰు࣓ൗႯᇐç
ၥєྠç҉ӼᇞҒਟƗ
ƥଗç്ְۢ
It is forbidden to use
unsustainable, ductile or
light-weight material to fix the
covering. Such as foam board
etc.
20-60mm
max.
3mm
max.
3mm
610mm
100mm
0
FFL
180mm
35mm
Push Plate 226mm
140mm
Outlet Drain Hole
Diameter 114mm
Inlet Drain Hole
Diameter 64mm
Toilet
Mounting
Holes
Diameter 19mm
Inlet Drain
mud guard
Outlet Drain
Mud Guard
Push Plate
Rough-In
Threaded
Mounting
Stud
20~60mm
9
180
230
“Click’’“Click’’
Install Plug:
ሆƥ
ؚӐઋۍ֬ܬᆭӱഏ܉ل
ቍ҉खঢ়ઋඤ५Ɨሔ൏Ɨ౯
ۻओѓఝ֬ԋձ࣐ྡྷ࿑ᄻτሔ
For the fixing of the long screw, there
are two groups of screw holes on the
bracket which are of different distance.
Please choose the right position
according to the size of the toilet bowl.
ᇞး൜ƥᄤᆭࡖτሔޱజుఴƗ༇шඪѰ٩ᇉཱི൏
ၢഏƗࡦҷڕႼസཊཧè
Important remind: When the concealed tank fixed completely, it is
important to test leaking with water upon 12 hours before fixing wall.
ຢӵ൜ၰ
Sketch of installed frame
10
The thickness of fixed wall is 20~60mm
(measured from the front of frame to the finished tile surface)
ሆƥ
ሔྰు࣓ൗႯᇐç
ၥєྠç҉ӼᇞҒਟƗ
ƥଗç്ְۢ
It is forbidden to use
unsustainable, ductile or
light-weight material to fix the
covering. Such as foam board
etc.
20-60mm
max.
3mm
max.
3mm
610mm
100mm
0
FFL
180mm
35mm
Push Plate 226mm
140mm
Outlet Drain Hole
Diameter 114mm
Inlet Drain Hole
Diameter 64mm
Toilet
Mounting
Holes
Diameter 19mm
Inlet Drain
mud guard
Outlet Drain
Mud Guard
Push Plate
Rough-In
Threaded
Mounting
Stud
20~60mm
9
180
230
“Click’’“Click’’
Install Plug:
ሆƥ
ؚӐઋۍ֬ܬᆭӱഏ܉ل
ቍ҉खঢ়ઋඤ५Ɨሔ൏Ɨ౯
ۻओѓఝ֬ԋձ࣐ྡྷ࿑ᄻτሔ
For the fixing of the long screw, there
are two groups of screw holes on the
bracket which are of different distance.
Please choose the right position
according to the size of the toilet bowl.
ᇞး൜ƥᄤᆭࡖτሔޱజుఴƗ༇шඪѰ٩ᇉཱི൏
ၢഏƗࡦҷڕႼസཊཧè
Important remind: When the concealed tank fixed completely, it is
important to test leaking with water upon 12 hours before fixing wall.
ຢӵ൜ၰ
Sketch of installed frame
12
d
2. 3.
ઋۍןࢲӐ؎ເLUU
Adjusting length for Bolt is d+25mm as
shows.
ඪᆷܼҳ್ඪܼᄣࢃԑඞᆷܼ
ҳ್ѓఝ५
First install Drain Straight Pipe into Drain
Bend, and then install Flush Straight Pipe
into Hole on Bowl.
4. 5.
ҳ್ѓఝ
Install Bowl.
൲ᄕྡྷޱƗ౯ಙಱႼৼࢫҍयඪཊཧè
τሔ҉֥໑ƗःႼढ़߽ඪƗᄶӵҔӈ෬Ɨਬൈࡌकְè
After conducting a test run, confirm that no connections are leaking water.
Not installing the product properly may cause water leaks that could result in
flooding damage to property, such as household belongings.
1.
ѓఝྟ
Toilet bowl type
౯್࣐ҋᇮ
Proceed to step 2.
౯φᅽѓఝڿւ֬േ܄නଃඇ
࣐ྡྷτሔ
Install according to the Installation
Guide enclosed with the toilet bowl.
Install the toilet:
7. 8.
ಃԢւႼ݈Ⴙݡ૬ᄤᆷܼთຜܼ֬ࢹލഏ݈Ⴙ
Take out the sponge with silicon oil and smear it on connecting
edges of Straight Pipe and Bends.
ࢃघܼܼؒ֬८ؑռଏ֡࢟ƗѰಇԩષя
Chamfer and trim the cutting edges on the shortened Straight
pipes (as shows).
11
L2
L1
L1+3mm
L2+3mm
2
1
Install the toilet
1. 2. 3.
5. 6.
ࢃᆷܼٺѠҳ್ԑඪܼދඪܼ֥
໑Ѱ߉ནњൔ
Set Straight Pipes into Flush Bend and
Drain Bend properly, and marks lines.
4. 5. 6.
ԑඪᆷܼ߉ནњൔᆴ࡞4Ʀ
ඪᆷܼ߉ནњൔᆴ࡞4
L1 is the distance of two marks on Flush
Straight Pipe, and L2 is that of two marks
on Drainpipe Straight Pipe.
߉ནњൔ
Mark lines as shows.
۰ᆷܼ
Cut Straight Pipe just as shows.
ٺѠᄤۻᆷܼཤഏഏೕ߈
Ⴙᄣҳ್ѓఝƓԑඞᆷܼ૨چัτ
ሔ١൛ࡵççƔ
Add lubricant onto the Rubber Gaskets of
two Straight Pipes and set them into Bowl.
(Flush Pipe seal Gasket assembly see 3.1,
3.2 and 3.3).
3.1 3.2 3.3
૨چัτሔ൏ৼԑඞᆷܼ၉ఖҳ್ѓ
ఝ५ୄè
Seal Gasket A insert into Bowl with Flush Pipe
together.
૨چั*τሔƥ
Ŭ൵༼шࢃ૨چัሔ್ѓఝ५Ʀ
ŭಝޱࢃԑඞᆷܼೝ࣐૨چั*è
Seal Gasket B install:
➀ install the Gasket into Bowl first;
➁ then insert the Flush Pipe into the Seal Gasket.
ԑඞᆷܼ૨چั)τሔ൜ၰè
Seal Gasket A install
ԑඞᆷܼ૨چัè
Flush Pipe Seal
Gasket.
ԑඞᆷܼ૨چั*τሔ൜ၰè
Seal Gasket B install.
૨چั)
Seal Gasket A
૨چั*
Seal Gasket B
12
d
2. 3.
ઋۍןࢲӐ؎ເLUU
Adjusting length for Bolt is d+25mm as
shows.
ඪᆷܼҳ್ඪܼᄣࢃԑඞᆷܼ
ҳ್ѓఝ५
First install Drain Straight Pipe into Drain
Bend, and then install Flush Straight Pipe
into Hole on Bowl.
4. 5.
ҳ್ѓఝ
Install Bowl.
൲ᄕྡྷޱƗ౯ಙಱႼৼࢫҍयඪཊཧè
τሔ҉֥໑ƗःႼढ़߽ඪƗᄶӵҔӈ෬Ɨਬൈࡌकְè
After conducting a test run, confirm that no connections are leaking water.
Not installing the product properly may cause water leaks that could result in
flooding damage to property, such as household belongings.
1.
ѓఝྟ
Toilet bowl type
౯್࣐ҋᇮ
Proceed to step 2.
౯φᅽѓఝڿւ֬േ܄නଃඇ
࣐ྡྷτሔ
Install according to the Installation
Guide enclosed with the toilet bowl.
Install the toilet:
7. 8.
ಃԢւႼ݈Ⴙݡ૬ᄤᆷܼთຜܼ֬ࢹލഏ݈Ⴙ
Take out the sponge with silicon oil and smear it on connecting
edges of Straight Pipe and Bends.
ࢃघܼܼؒ֬८ؑռଏ֡࢟ƗѰಇԩષя
Chamfer and trim the cutting edges on the shortened Straight
pipes (as shows).
11
L2
L1
L1+3mm
L2+3mm
2
1
Install the toilet
1. 2. 3.
5. 6.
ࢃᆷܼٺѠҳ್ԑඪܼދඪܼ֥
໑Ѱ߉ནњൔ
Set Straight Pipes into Flush Bend and
Drain Bend properly, and marks lines.
4. 5. 6.
ԑඪᆷܼ߉ནњൔᆴ࡞4Ʀ
ඪᆷܼ߉ནњൔᆴ࡞4
L1 is the distance of two marks on Flush
Straight Pipe, and L2 is that of two marks
on Drainpipe Straight Pipe.
߉ནњൔ
Mark lines as shows.
۰ᆷܼ
Cut Straight Pipe just as shows.
ٺѠᄤۻᆷܼཤഏഏೕ߈
Ⴙᄣҳ್ѓఝƓԑඞᆷܼ૨چัτ
ሔ١൛ࡵççƔ
Add lubricant onto the Rubber Gaskets of
two Straight Pipes and set them into Bowl.
(Flush Pipe seal Gasket assembly see 3.1,
3.2 and 3.3).
3.1 3.2 3.3
૨چัτሔ൏ৼԑඞᆷܼ၉ఖҳ್ѓ
ఝ५ୄè
Seal Gasket A insert into Bowl with Flush Pipe
together.
૨چั*τሔƥ
Ŭ൵༼шࢃ૨چัሔ್ѓఝ५Ʀ
ŭಝޱࢃԑඞᆷܼೝ࣐૨چั*è
Seal Gasket B install:
➀ install the Gasket into Bowl first;
➁ then insert the Flush Pipe into the Seal Gasket.
ԑඞᆷܼ૨چั)τሔ൜ၰè
Seal Gasket A install
ԑඞᆷܼ૨چัè
Flush Pipe Seal
Gasket.
ԑඞᆷܼ૨چั*τሔ൜ၰè
Seal Gasket B install.
૨چั)
Seal Gasket A
૨چั*
Seal Gasket B
14
Cleaning the Filter of the Fill Valve
φഏඔҧቛƗܸх࣐ඪً࢟ƗಝޱҾ༶࣐ඪًè
൜ƗҾा࣐ඪًƗಝޱႯඪ౩༨ݝະƗࠎᆇ
Ⴏඞሷ౩ԩ༅è
φᅽთഏඔཔ٘֬ҋᇮҧቛƗѓࢃ࣐ඪًτሔߴჷ
দ֬໑ᇉè
1. Close the water shutoff valve, and then remove the fill valve as
described above.
2. As shown in the figure, disassemble the fill valve, and then either
clean the filter with water or use a brush to clean any dirt from it.
3. To install, follow the procedure in reverse to return the fill valve to
its original position.
13
Servicing procedures
Replacing the Flush Valve
1.
Ҿ༶ѰটԢ٤ࡾᅾè
Remove the splash guard and pull it out.
2.
5.
ট࣌ᇖ൜ট൴Ҿ༶࣌ᆭࡖè
Remove the hold-down bracket by pulling on the tab indicated.
3.
ܸхඪམᇖ࣐֬ඪً࢟Ɨಝޱφ༶ಁࡸഏ֬φ୭࣐
ྡྷԑඪè
Close the shutoff valve in the tank, and then push the button on the
actuator to flush the water.
4.
6.
টఖԑඪًƗ࿏ሎটۍè
Pull the flush valve up, and rotate the rods.
φህট൴Ҿ༶ಁࡸè
Push on the tab to remove the actuator.
7.
টԢ൏࿏ሎᆣ۸ሔᇉè
Rotate the whole unit as you pull it out.
ࢃԑඪً֬ۻটۍ౧ྃᇇႾҮè
Tilt the two pull-up rods of the flush valve to the right.
8.
ԑඪً၉ؑ֬ཤࡸढ़ၢҾ༶࣐ྡྷ౩ࢸࠎ۾ߗè
At the other end of the flush valve, the rubber piece can be
removed for cleaning or to be replaced.
9.
φᅽთഏඔཔ٘֬ҋᇮҧቛƗѓࢃਲ਼ࡸτሔߴඪམè
To install the parts back into the tank, do the reverse order.
14
Cleaning the Filter of the Fill Valve
φഏඔҧቛƗܸх࣐ඪً࢟ƗಝޱҾ༶࣐ඪًè
൜ƗҾा࣐ඪًƗಝޱႯඪ౩༨ݝະƗࠎᆇ
Ⴏඞሷ౩ԩ༅è
φᅽთഏඔཔ٘֬ҋᇮҧቛƗѓࢃ࣐ඪًτሔߴჷ
দ֬໑ᇉè
1. Close the water shutoff valve, and then remove the fill valve as
described above.
2. As shown in the figure, disassemble the fill valve, and then either
clean the filter with water or use a brush to clean any dirt from it.
3. To install, follow the procedure in reverse to return the fill valve to
its original position.
13
Servicing procedures
Replacing the Flush Valve
1.
Ҿ༶ѰটԢ٤ࡾᅾè
Remove the splash guard and pull it out.
2.
5.
ট࣌ᇖ൜ট൴Ҿ༶࣌ᆭࡖè
Remove the hold-down bracket by pulling on the tab indicated.
3.
ܸхඪམᇖ࣐֬ඪً࢟Ɨಝޱφ༶ಁࡸഏ֬φ୭࣐
ྡྷԑඪè
Close the shutoff valve in the tank, and then push the button on the
actuator to flush the water.
4.
6.
টఖԑඪًƗ࿏ሎটۍè
Pull the flush valve up, and rotate the rods.
φህট൴Ҿ༶ಁࡸè
Push on the tab to remove the actuator.
7.
টԢ൏࿏ሎᆣ۸ሔᇉè
Rotate the whole unit as you pull it out.
ࢃԑඪً֬ۻটۍ౧ྃᇇႾҮè
Tilt the two pull-up rods of the flush valve to the right.
8.
ԑඪً၉ؑ֬ཤࡸढ़ၢҾ༶࣐ྡྷ౩ࢸࠎ۾ߗè
At the other end of the flush valve, the rubber piece can be
removed for cleaning or to be replaced.
9.
φᅽთഏඔཔ٘֬ҋᇮҧቛƗѓࢃਲ਼ࡸτሔߴඪམè
To install the parts back into the tank, do the reverse order.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Toto WH171A Installation Instructions Manual
- Categoria
- Prodotti sanitari
- Tipo
- Installation Instructions Manual
- Questo manuale è adatto anche per
in altre lingue
- English: Toto WH171A
Documenti correlati
Altri documenti
-
Edgewater Networks 318CC Owner Assistance Manual
-
Regal 42 Fly-Grande Coupe Manuale del proprietario
-
CASAINC JUN-TOILET-026 Manuale utente
-
Johnson Hardware IB-412 R01 Manuale utente
-
-
Bayliner 1983 Explorer Manuale del proprietario
-
THETFORD Tecma® Easy Fit Guida d'installazione
-