ProLights DISPLAYCOBFC Manuale utente

Marca: ProLights

Modello: DISPLAYCOBFC

Categoria: Stroboscopi

Tipo: Manuale utente

USER MANUAL

MANUALE UTENTE

DISPLAYCOBFC

EN - IT

DIFFUSED LIGHT PROJECTOR

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.01-06/15

DISPLAYCOBFC

Packing content

• DISPLAYCOBFC

• Mount bracket (2 pc.)

• Power cable

• User manual

TABLE OF CONTENTS

Safety

General instructionsGeneral instructions

Warnings and installation precautionsWarnings and installation precautions

1 Introduction

1. 1 Description1. 1 Description

1. 2 Technical specications1. 2 Technical specications

1. 3 Operating elements and connections1. 3 Operating elements and connections

2 Installation

2. 1 Mounting2. 1 Mounting

3 Functions and settings

3. 1 Operation3. 1 Operation

3. 2 Basic3. 2 Basic

3. 3 Menu structure3. 3 Menu structure

3. 4 Auto show3. 4 Auto show

3. 5 Static mode3. 5 Static mode

3. 6 Manual mode3. 6 Manual mode

3. 7 Master/Slave mode3. 7 Master/Slave mode

3. 8 Linking3. 8 Linking

3. 9 DMX mode3. 9 DMX mode

3. 10 DMX addressing 3. 10 DMX addressing

3. 11 Connection of the DMX line3. 11 Connection of the DMX line

3. 12 Construction of the DMX termination3. 12 Construction of the DMX termination

3. 13 DMX control3. 13 DMX control

3. 14 Dimmer3. 14 Dimmer

3. 15 Back light3. 15 Back light

3. 16 Fixture information3. 16 Fixture information

3. 17 White balance3. 17 White balance

3. 18 Temperature3. 18 Temperature

4 Maintenance

4. 1 Maintenance and cleaning the unit4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement4. 2 Fuse replacement

4. 3 Trouble shooting4. 3 Trouble shooting

DISPLAYCOBFC

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bumps;

- in places with a temperature of over 40 °C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

DISPLAYCOBFC

- 1 - INTRODUCTION

1.1 DESCRIPTION

DisplayCob FC is the compact version of the popular StudioCob FC - perfect for an installation or indoor

venues. DisplayCob FC uses a 60 W COB LED source RGB / FC, combined with a special parabolic reector

built in aluminium which develops an extremely bright and homogeneous output and interchangeable

lens system to switch from 60° (incl.) to 30° (incl.) and 15° (opt.).

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 60W COB RGB / FC LED

• Luminous ux: 2’055lm

• Lux: (60°) 122,7lx @3 m full

• Lux: (30°) 358,5lx @3 m full

• Source life expectancy: > 30.000 h

OPTICS

• Beam angle: 60°

• Field angle: 80°

• Lens type: parabolic reector in combination with HD fresnel lens

• Additional optics: 30° (inc) - 15° (opt)

COLOUR SYSTEM

• Colour mixing: RGB / FC

• White presets: 3.200 K ~ 10.000K

• Colour wheel: virtual colour wheel with presets

• Macros: built-in white presets

DYNAMIC EFFECTS

• Static colour mode: selection of static colour

• Manual colour mode: manual adjustment of colour

• Auto mode: built-in programs with execution speed adjustment

• BODY

• Body: sturdy die-cast aluminium body conceived for long-time durability

• Body colour: black

CONTROL

• Protocols: DMX512

• DMX channels: 3 / 5 / 8channel

• Display: black OLED high resolution display

• Firmware upgrade: yes, via USB - DMX interface (UPBOX1) not included

• Master/Slave: for synchronized operation of more units linked in a chain

ELECTRONICS

• Dimmer: linear 0 ~ 100% electronic dimmer

• Dimmer curves: 4 dierent dimming curves available

• Strobe / shutter: 1 - 28 Hz, electronic

• Operating temperature: -10° ~ +45°

DISPLAYCOBFC

• Flicker: icker free operation

• Selectable PWM: 600 ~ 25.000 Hz

ELECTRICAL

• Power supply: 100-240 V – 50/60 Hz

• Power consumption (at 230 V): 75W

• Power consumption (at 120 V): 70W

• Output (at 230 V): 24 units on a single power line

PHYSICAL

• Cooling: passive cooling and fan-free

• Sospension and xing: double hanging bracket suitable for safe hanging and for oor positioning

• Signal connection: XLR 5p IN/OUT connectors

• Power connection: moulded IP power IN connector

• IP rating: 20

• Dimensions (WxHxD): 166x118x250mm

• Weight: 1,85kg

Technical drawing Fig.1

DISPLAYCOBFC

1.3 OPERATING ELEMENTS AND CONNECTIONS

Fig.2

1. MOUNTING BRACKET

2. SCREW for the mounting bracket

3. CONTROL PANEL with display and 4 button

used to access the control panel functions

and manage them

4. DMX IN (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+, 4 N/C, 5 N/C

5. DMX OUT (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+, 4 N/C, 5 N/C

6. GND POINT grounding the xture to the earth

7. MAIN FUSE HOLDER: replace a burnt-out fuse

by one of the same type only (T1/250V)

8. SAFETY RING to attach safety cable

9. CONNECTION CABLE with Shuko plug

(100-240V~/50-60Hz).

Rear panel

DISPLAYCOBFC

- 2 - INSTALLATION

2.1 MOUNTING

DISPLAYCOBFC may be set up on a solid and even surface. The unit can also be mounted upside down to a

cross arm. For xing, stable mounting clips are required. The mounting place must be of sucient stability

and be able to support a weight of 10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the xture’s being used.

• Install the projector at a suitable location by means of the mounting bracket (1).

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.

• Adjust the projector and use the screw to slightly release or tighten the locking mechanism of the

bracket if is necessary (2).

Fig.3

DISPLAYCOBFC

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). Then the unit is ready for operation

and can be operated via a DMX controller or it independently performs its show program in succession.

To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and o via a light switch.

3.2 BASIC

Access control panel functions using the four panel buttons located directly underneath the black OLED

display (g.4).

Fig.4 - Functions of the buttons

MENU UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or conrm the

current function value or

option within a menu

MENU UP DOWN ENTER

DISPLAYCOBFC

3.3 MENU STRUCTURE

MENU (LEVEL 1) (LEVEL 2) (LEVEL 3) REMARK

1 Auto Show

Auto Show

< Auto 1 >

< Auto 2 >

< Auto 3 >

< Auto 4 >

Speed

< 100 >

Default: Auto 1; Speed:100

2 Static

Fixed Color

< R >

< G >

< B >

< GB >

< RB >

< RG >

< RGB >

Default: RGB

Manual Color

Value

< R=255 >

< G=255 >

< B=255 >

Default: RGB=255

3 Dimmer Mode

Dimmer Mode

< O >

< DIM 1 >

< DIM 2 >

< DIM 3 >

Default: O

4 Fix Installation

O

Default: 0

5 Back Light

Back Light

< On >

< 10 s >

< 20 s >

< 30 s >

Default: 10 s

6 Information

Auto

Fix Hours

Version

Test

< 9999 H >

< V1.0 >

7 DMX Address

< 001 > Default: 001

8 DMX Channel

< 3Ch >

< 5Ch >

< 8Ch >

Default: 8Ch

9 Master/Slave

<Slave>

Default: Slave

10 White Balance

Balance

<R=255>

<G=255>

<B=255>

Value

<R=255>

<G=255>

<B=255>

11 LED Frequency

<600Hz>

<1200Hz>

<2000Hz>

<4000Hz>

<25KHz>

Default:1200Hz

12 Temperature

58°C

DISPLAYCOBFC

3.4 AUTO SHOW

If no DMX control signal is present at the DMX INPUT, the unit independently runs through its show pro-

gramme provided that the blackout mode is switched o:

• Press the button MENU so many times until the display shows Auto Show, then press the button ENTER.

• Press the button UP/DOWN to switch between the show Auto 1 - Auto 4. The unit will operate in show

mode.

• Using the button UP/DOWN to select the desired run speed slow-fast 0-100.

• Press the button ENTER to save the setting.

IMPORTANT: Programs Auto 1 - 4 are fully pre-programmed and will not be altered by changes. Instead,

3.5 STATIC MODE

This xture has the ability to accept custom static color settings. Access these chases via the control panel

on the back of the xture.

• Press the button MENU so many times until the display shows Static, then press the button ENTER.

• Select Fixed Color through the buttons UP/DOWN, then press the button ENTER.

• Set the colors R , G , B, GB, RB, RG, RGB, through the buttons UP/DOWN, then press the button ENTER.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.6 MANUAL MODE

This mode allows to combine the colors red, green and blue (R, G, B).

• Press the button MENU so many times until the display shows Static, then press the button ENTER.

• Select Manual Color through the buttons UP/DOWN, then press the button ENTER.

• Select the color R, G, B through the buttons UP/DOWN, then press the button ENTER.

• Using UP/DOWN button, select the desired color value 000 - 255.

• Press ENTER button to continue to the next color R, G, B.

• Continue until the desired mix is obtained.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.7 MASTER/SLAVE MODE

This mode will allow you to link up the units together without a controller. Choose a unit to function as the

Master. The unit must be the rst unit in line; other units will work as slave.

• Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the

units. For longer cable runs we suggest a terminator at the last xture (see page 13).

• Set on master xture the desired program (see section 3.4).

• Set the slaves to the same DMX modes.

3.8 LINKING

1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

3.9 DMX MODE

• Press the button MENU so many times until shows 3 Ch, 5 Ch or 8 Ch and press the button ENTER to con-

rm.

• Press the button UP/DOWN to select the desired DMX address 001 - 512. Press and hold to scroll quickly.

DISPLAYCOBFC

DMX Address: 57DMX Address: 40DMX Address: 33 DMX Address: 49

Fig.5 - Example 8 DMX channels conguration

............

DMX512 Controller

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

3 33 33-35 36 39 42

5 33 33-37 38 43 48

8 33 33-40 41 49 57

Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

The tables on page 14 indicate the operating mode and DMX value. DISPLAYCOBFC is equipped with

5-pole XLR connections.

3.10 DMX ADDRESSING

To able to operate the DISPLAYCOBFC with a light controller, adjust the DMX start address for the rst a

DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX

channel, adjust the start address 33 on the DISPLAYCOBFC. The other functions of the light eect panel are

then automatically assigned to the following addresses.

An example with the start address 33 is shown below:

DISPLAYCOBFC

Fig.6

Fig.7

3.11 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.12 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

Example:

3 pin XLR connector

DISPLAYCOBFC

3.13 DMX CONTROL

3 CHANNELS

MODE

FUNCTION DMX

Value

3 Ch

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

5 CHANNELS

MODE

FUNCTION DMX

Value

5 Ch

DIMMER

0~100% 000 - 255

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

STROBE

No Function

Strobe slow to fast

000 - 010

011 - 255

8 CHANNELS

MODE

FUNCTION DMX

Value

8 Ch

DIMMER

0~100% 000 - 255

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

STROBE/AUTO SPEED

No Function

Strobe slow to fast

000 - 010

011 - 255

AUTO SPEED SLOW TO FAST

Speed slow to fast 000 - 255

COLOR

No Function

Color Macros

000 - 015

016 - 255

AUTO MODE

RGB mode

Pulse eect 0-100%

Pulse eect 100%-0

Pulse eect 100%-0-100%

Auto fade transition

Auto snap transition (3 colors)

Auto snap transition (7 colors)

000 - 010

011 - 050

051 - 090

091 - 130

131 - 170

171 - 210

211 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode 1 (fast speed)

Dimmer speed mode 2 (middle speed)

Dimmer speed mode 3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

DISPLAYCOBFC

3.14 DIMMER

• To enter dimmer mode and choose to simulate dierent dimming curves, press the MENU button re-

peatedly until the display shows Dimmer Mode, then press the ENTER button.

• Press the button MENU repeatedly until Dimmer Mode shows, and press ENTER button to accept.

• Use the button UP/DOWN to select a dimmer curve O - Dimmer1 - Dimmer2 - Dimmer3.

• Press ENTER button to conrm the selection.

• Press the MENU button to go back or to meet the waiting time to exit from the setup menu automati-

cally.

3.15 BACK LIGHT

• To activate backlight display press the button MENU so many times until shows Back Light, and press the

button ENTER to conrm.

• Press the button UP/DOWN to select On - 10S - 20S - 30S. Press ENTER button to conrm the selection.

• Press the MENU button to go back or to meet the waiting time to exit from the setup menu automati-

cally.

3.16 FIXTURE INFORMATION

1. Press the MENU button so many times until shows Information, and then press ENTER button.

2. Use UP/DOWN button to select: Auto Test - Fixture Hours - Version.

3. Press ENTER button to conrm the selection.

4. Press the MENU button to go back or to meet the waiting time to exit from the setup menu automati-

cally.

Auto Test

This setting starts the products test sequence. Select Auto Test.

Fixture Hours

This option shows the user the amount of hours the DISPLAYCOBFC has been in use throughout its

lifetime. Select Fixture Hours.

Version

This option shows the user the software version currently installed in the unit. Select Version.

3.17 WHITE BALANCE

Enter the White balance to adjust the Red, Green, and Blue parameter to make dierent whites.

• Press the button MENU so many times until shows White Balance, and press the button ENTER to conrm.

• Select the color R, G, B through the buttons UP/DOWN, then press the button ENTER.

• Using UP/DOWN button, select the desired color value 125 - 255.

• Press ENTER button to continue to the next color R, G, B.

• Continue until the desired mix is obtained.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.18 TEMPERATURE

• To read the value of the internal temperature of the device, press the MENU button repeatedly until the

display shows Temperature, and then press the ENTER key to read the value.

• Press the MENU button to go back or wait a few seconds to exit the setup menu.

DISPLAYCOBFC

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch o the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

4.2 FUSE REPLACEMENT

1. Remove the safety cap by a screwdriver.

2. Replace the blown fuse with a fuse of the exact same type and rating (T1/250V).

3. Install the safety cap, and reconnect power.

4.3 TROUBLESHOOTING

Fig.8

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• All color faders set to 0

• Faulty LED

• Faulty LED board

• Check the power supply voltage

• Increase the value of the dimmer channels

• Increase the value of the color channels

• Replace the LED board

General low light intensity

• Dirty lens assembly • Clean the xture regularly

Fixture does not power up

• No power

• Loose or damaged power cord

• Faulty internal power supply

• Check for power on power outlet

• Check power cord

• Replace internal power supply

Fixture does not respond to DMX

• Wrong DMX addressing

• Damaged DMX cables

• Bouncing signals

• Check control panel and unit addressing

• Check DMX cables

• Install terminator as suggested

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

Note

REV.01-06/15

Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.

La riproduzione - anche parziale - per propri scopi commerciali è vietata.

Al ne di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modicare, in

qualunque momento e senza preavviso, le speciche menzionate nel presente manuale di istruzioni.

Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it

DISPLAYCOBFC

• DISPLAYCOBFC

• Staa di ssaggio (2pz.)

• Cavo di alimentazione

• Manuale utente

Contenuto dell'imballo:

INDICE

Sicurezza

Avvertenze generaliAvvertenze generali

Attenzioni e precauzioni per l’installazioneAttenzioni e precauzioni per l’installazione

1 Introduzione

1. 1 Descrizione1. 1 Descrizione

1. 2 Speciche tecniche1. 2 Speciche tecniche

1. 3 Elementi di comando e di collegamento1. 3 Elementi di comando e di collegamento

2 Installazione

2. 1 Montaggio2. 1 Montaggio

3 Funzioni e impostazioni

3. 1 Funzionamento3. 1 Funzionamento

3. 2 Impostazione base3. 2 Impostazione base

3. 3 Struttura menu3. 3 Struttura menu

3. 4 Modalità automatica3. 4 Modalità automatica

3. 5 Modalità statica3. 5 Modalità statica

3. 6 Modalità manuale3. 6 Modalità manuale

3. 7 Modalità Master/Slave3. 7 Modalità Master/Slave

3. 8 Collegamento3. 8 Collegamento

3. 9 Modalità DMX 3. 9 Modalità DMX

3. 10 Indirizzamento DMX3. 10 Indirizzamento DMX

3. 11 Collegamenti della linea DMX3. 11 Collegamenti della linea DMX

3. 12 Costruzione del terminatore DMX3. 12 Costruzione del terminatore DMX

3. 13 Canali DMX3. 13 Canali DMX

3. 14 Dimmer3. 14 Dimmer

3. 15 Back Light3. 15 Back Light

3. 16 Informazioni sul dispositivo3. 16 Informazioni sul dispositivo

3. 17 Bilanciamento bianco3. 17 Bilanciamento bianco

3. 18 Temperatura3. 18 Temperatura

4 Manutenzione

4. 1 Manutenzione e pulizia del sistema ottico4. 1 Manutenzione e pulizia del sistema ottico

4. 2 Sostituzione fusibile4. 2 Sostituzione fusibile

4. 3 Risoluzione dei problemi4. 3 Risoluzione dei problemi

DISPLAYCOBFC

ATTENZIONE! Prima di effettuare qualsiasi operazione con l’unità, leggere con attenzione

questo manuale e conservarlo accuratamente per riferimenti futuri. Contiene informazioni

importanti riguardo l’installazione, l’uso e la manutenzione dell’unità.

SICUREZZA

Avvertenze generali

• I prodotti a cui questo manuale si riferisce sono conformi alle Direttive della Comunità Europea e per-

tanto recano la sigla .

• Il dispositivo funziona con pericolosa tensione di rete 230V~. Non intervenire mai al suo interno al di

fuori delle operazioni descritte nel presente manuale; esiste il pericolo di una scarica elettrica.

• È obbligatorio eettuare il collegamento ad un impianto di alimentazione dotato di un’eciente messa

a terra (apparecchio di Classe I secondo norma EN 60598-1). Si raccomanda, inoltre, di proteggere le

linee di alimentazione delle unità dai contatti indiretti e/o cortocircuiti verso massa tramite l’uso di

interruttori dierenziali opportunamente dimensionati.

• Le operazioni di collegamento alla rete di distribuzione dell’energia elettrica devono essere eettuate

da un installatore elettrico qualicato. Vericare che frequenza e tensione della rete corrispondono alla

frequenza ed alla tensione per cui l’unità è predisposta, indicate sulla targhetta dei dati elettrici.

• L’unità non per uso domestico, solo per uso professionale.

• Evitare di utilizzare l’unità:

- in luoghi soggetti a vibrazioni, o a possibili urti;

- in luoghi a temperatura superiore ai 40°C.

• Evitare che nell’unità penetrino liquidi inammabili, acqua o oggetti metallici.

• Non smontare e non apportare modiche all’unità.

• Tutti gli interventi devono essere sempre e solo eettuati da personale tecnico qualicato. Rivolgersi al

più vicino centro di assistenza tecnica autorizzato.

• Se si desidera eliminare il dispositivo denitivamente, consegnarlo

per lo smaltimento ad un’istituzione locale per il riciclaggio.

Attenzioni e precauzioni per l’installazione

• Se il dispositivo dovesse trovarsi ad operare in condizioni dierenti da quelle descritte nel presente

manuale, potrebbero vericarsi dei danni; in tal caso la garanzia verrebbe a decadere. Inoltre, ogni altra

operazione potrebbe provocare cortocircuiti, incendi, scosse elettriche, rotture etc.

• Prima di iniziare qualsiasi operazione di manutenzione o pulizia sull’unità togliere la tensione dalla rete

di alimentazione.

• È assolutamente necessario proteggere l’unità per mezzo di una fune di sicurezza. Nell’eseguire qual-

siasi intervento attenersi scrupolosamente a tutte le normative (in materia di sicurezza) vigenti nel

paese di utilizzo.

• Installare l’unità in un luogo ben ventilato.

• Mantenere i materiali inammabili ad una distanza di sicurezza dall’unità.

• I ltri, le lenti o gli schermi ultravioletti se danneggiati possono limitare la loro ecienza.

• I LED devono essere sostituiti se danneggiati o termicamente deformati.

• Non guardare direttamente il fascio luminoso. Tenete presente che i veloci cambi di luce possono pro-

vocare attacchi d’epilessia presso persone fotosensibili o epilettiche.

• Non toccare l’alloggiamento del prodotto quando è in funzione perché potrebbe essere molto caldo.

• Questo prodotto è stato progettato e costruito per l’utilizzo indicato in questa documentazione. Qual-

siasi altro utilizzo non espressamente indicato potrebbe pregiudicare la funzionalità del prodotto e/o

rappresentare fonte di pericolo.

• Si declina ogni responsabilità derivata dall’uso improprio del prodotto.

La pagina sta caricando ...

ProLights DISPLAYCOBFC Manuale utente

Marca: ProLights

Modello: DISPLAYCOBFC

Categoria: Stroboscopi

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: ProLights DISPLAYCOBFC User manual

Documenti correlati

Altri documenti

Sagitter SG HALOPCW1528 Manuale utente