DTS SCENA COMPACT LED 50 Manuale utente

Made in Italy

SCENA COMPACT LED 50

User’s Manual rel. 1.0 GB

D.T.S. Illuminazione s.r.l. – ITALY

http://www.dts-lighting.it/

2

Le informazioni contenute in questo documento sono state attentamente redatte e

controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.

Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato,

riprodotto per intero o in parte senza previo consenso scritto della D.T.S .

D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche

estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna

responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and

checked. However, no responsibility will be taken for any errors. All rights are

reserved and this document cannot be copied, photocopied or reproduced, in part or

completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to

any of its products without prior notice. D.T.S. assumes no responsibility for the use or

application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées

avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas

photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement

préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,

fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline

toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits

décrits.

Las informaciones contenidas en este documento han sido cuidadosamente

redactadas y controladas. Con todo, no se asume ninguna responsabilidad por

eventuales inexactitudes. Todos los derechos han sido reservados y este documento

no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa

autorización escrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de

carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los

productos o de los circuitos descritos.

3

INDEX:

1- SYMBOLS 4

2- GENERAL WARNING 4

3- GENERAL WARRANTY CONDITION 4

4- TECHNICAL FEATURES 5

5- ACCESSORIES 6

6- IMPORTANT SAFETY INFORMATION 7

6.1 Fire prevention

6.2 Prevention of electric shock

6.3 Safety

7- INPUT / OUTPUT CONNECTIONS 7

8- DMX SIGNAL CONNECTION 8

8.1 DMX Addresses

8.2 Selecting the DMX address

9- FIRMWARE UPDATING 9

10- DISPLAY FUNCTIONS 10

11- DMX PROTOCOL 14

4

!

1- SYMBOLS

Graphic symbols used on this manual:

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC SHOCK

RISK

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS YOU CAN PLACE THE

UNIT ON NORMALLY FLAMMABLE SURFACES

THIS SYMBOL INDICATES THE MINIMUM

DISTANCE TO BE KEPT BETWEEN THE DEVICE

AND THE LIT OBJECT

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important

information regarding safety during installation , use and maintenance.

The device is not for domestic use and must be installed by a qualified electrician or

experienced person.

Always disconnect the device from the mains before maintenance.

The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing

material defects.

LED 30 cm

5

4- TECHNICAL FEATURES

OVERVIEW

SCENA COMPACT LED 50 is a compact, lightweight, DMX-controlled projector

featuring a single high-power LED, and a wide excursion zoom, enabling it to be used

as a Beam or a very wide Wash.

SCENA COMPACT LED 50 is a modern alternative to conventional lights, improving

light quality, flexibility of use and installation, energy savings and component duration.

In fact the fixture doesn’t heat up, and the projection is always flicker free.

Also, the dimming curves are similar to those of halogen lamps.

The unit is available with PC or Fresnel lenses.

PRODUCT CODES:

03.TS023.46.A SCENA COMPACT LED 50 PC *White 3.000°K *Black

03.TS023.46.F SCENA COMPACT LED 50 FR *White 3.000°K *Black

03.TS024.46.A SCENA COMPACT LED 50 PC *White 4.000°K *Black

03.TS024.46.F SCENA COMPACT LED 50 FR *White 4.000°K *Black

03.TS025.46.A SCENA COMPACT LED 50 PC *White 5.600°K *Black

03.TS025.46.F SCENA COMPACT LED 50 FR *White 5.600°K *Black

LED Technology

1 x White LED (3.000 °K, 4000°K or 5600°K)

CRI > 90; LED Max power: 50W

Optical group

Linear zoom:

PC version (Ø 90 mm PC lens) from 10° to 76°; 2000 Lux / 3 m

Fresnel version (Ø 112 mm FR lens) from 14° to 77°; 1850 Lux / 3 m

Control

2 DMX channels

4 digit 7 segments display + 4 soft keys

Connectors

Power supply: POWERCON IN & OUT connectors

DMX: 5 poles In & Out connectors

Power supply

Electronic full-range AC 90-260V , 50/60 Hz

Weight

4 Kg (PC version)

3,7 Kg (FR version)

6

DIMENSIONS

5- ACCESSORIES

As standard

1 x User’s Manual

1 x POWERCON male cable connector (D.T.S. Code 0520P014)

1 x XLR 5 pins male cable connector (D.T.S. Code 0508B028)

1 x XLR 5 pins female cable connector (D.T.S. Code 0508B027)

Optional (on request)

- “C” Clamp G60 (Max. Load. 50 Kg) *Black finish (D.T.S. Code 0521A004)

- Barndoor for SCENA COMPACT *Black finish (D.T.S. Code 03.TA206)

- Filterframe for SCENA COMPACT *Black finish (D.T.S. Code 02M00422.46)

7

7- IMPORTANT SAFETY INFORMATION

7.1 Fire prevention:

It is permissible to place the unit on normally flammable surfaces.

Suitable for mounting on normally flammable materials surfaces greater than 200°C

with some combustion time lag.

Minimum distance from the closest illuminable surface: 30 cm.

Replace any blown or damaged fuses only with those of identical value (1AT).

7.2 Prevention from electric shock:

High voltage is present inside the unit.

Unplug the unit prior to performing any operation which involves touching the inside of

the unit.

This equipment must be grounded, do not connect to non-grounded supplies.

The use of a thermal magnetic circuit breaker is recommended for each SCENA

COMPACT LED 50 unit. Use only AC supplies 90-260V , 50 / 60 Hz.

SCENA COMPACT LED 50 should never be located in position exposed to rain or in

areas of extreme humidity.

A good air ventilation is essential for proper equipment work.

7.3 Safety:

The external surface of the unit may exeed 50°C; never handle the unit until at least 5

minutes have elapsed since the unit was turned off.

Never install the unit in an enclosed area lacking sufficient air flow.

The ambient temperature should not exeed 40°C and should not be lower than -10°C.

8- INPUT / OUTPUT CONNECTIONS

FUSE 1AT

DMX OUT

XLR 5 Pins Male Panel Connector

MAINS AC INPUT 90-260V , 50/60 Hz

DMX IN

XLR 5 Pins Female Panel Connector

DISPLAY PANEL

MAINS AC OUTPUT 90-260V , 50/60 Hz

MAX 16A

!

8

9- DMX SIGNAL CONNECTION:

The unit operates using a digital DMX 512 signal.

Connection between the controller and the unit or between units must be carried out

using a two pair screened ø 0.5 mm.

Ensure that the conductors do not touch each other.

Do not connect the cable ground to the DMX connector chassis.

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector

plug and connect it to the next projector by connecting the DMX OUT plug on the first

unit to the DMX IN plug of the second one.

In this way, all the projectors are cascade connected.

If the display showing the DMX address flashes, then one of the following errors has

occurred:

- DMX signal not present

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we

suggest to use a DMX terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

Between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of

the DMX line.

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

5

3

4 2

1

1=GND

2=DATA-

3=DATA+

CONTROLLER

S T A N D A R D

D M X 5 1 2

DMX OUT DMX OUT

DMX IN DMX IN

DMX OUT

DMX IN

DMX OUT

9

9.1 DMX addresses

SCENA COMPACT LED 50 can be controlled with 2 DMX channels.

In order to use the unit in 2 DMX channels mode, set the following addresses on the

mixer:

Projector 1 A001

Projector 2 A003 If you want to select the next projector, just add “2”

Projector 3 A005

….. A….

projector 6 A011

9.2 Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX address. The numbers

on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop

flashing and the projector is now controlled by the new DMX address.

TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more

quickly and you get a faster selection.

2) Press ENTER to confirm your selection. The numbers on the display will stop

flashing and the projector is now controlled by the new DMX address.

10- FIRMWARE UPDATING

To update the software version of the SCENA COMPACT LED 50 you need:

- D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008)

- USB-DMX Driver for the D.T.S. RED BOX interface

- “D.T.S. Firmware upgrade utility” program installed on PC

- Latest firmware release available for SCENA COMPACT LED 50 unit

Updating the software version.

Please follow the procedure below to perform the update:

1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the

unit software.

2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.

3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.

4. Send the new software version into the unit by using “D.T.S. Firmware upgrade

Utility” program.

10

Up-Down

MENU

ENTERUp-Down

Up-DownENTER

ENTER

Up-Down

MENU

ENTER

Up-Down

ENTER

Up-Down

ENTER

10- DISPLAY FUNCTIONS

DISPLAY FUNCTIONS

The SCENA COMPACT LED 50 display panel shows all the available functions.

Using these functions, it is possible to change some of the parameters and add some

functions. Changing the D.T.S. setting can vary the functions of the unit so that it does

not respond to the DMX 512 used to control it. Carefully follow the instructions below

before carrying out any variations or selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired

function.

Software version 1.00

REVERSE DISPLAY

Reverses display's reading depending on

the mounting position (on the ground or

suspended).

DISPLAY STAND BY

To turn off the display (after 5 seconds)

Or leave it always on.

DMX MODE

To select DMX mode : 2 DMX channels

mode (default), 1 DMX channel mode,

3 DMX channels mode or Manual mode.

Manual mode can also be activated by

pressing at the same time the “UP’’ +

”DOWN” buttons on unit display for 3

seconds (“A001”).

Suspended

Position

Floor

Position

Display

Off

Display

Always on

Default DMX Mode

2 Channels

Manual Mode

1 DMX channel mode

3 DMX channels mode

11

With BOOST active, the LED’S

current is set to Max value.

(30% more gain compared to

BOOST Off)

Default = Disabled

Up-Down

MENU

ENTER

Up-Down

ENTER

Up-Down

Up-DownENTER

ENTER

Up-Down

ENTER

Up-DownENTER

ENTER

MENU

Up-Down Up-DownENTER

ENTER

LED

Led Min/Max, Smooth, Compression,

Sync and Boost level values settings

LED MINIMUM VALUE

This menu allows to select the

minimum levels for white

LED MAXIMUM VALUE

This menu allows to select the

maximum levels for white

These settings have priority

on Master Dimmer channel

SMOOTH VALUE

This menu allows to select the value of

the delay (in milliseconds) for Dimmer

channel reaction to DMX or Program

variation.

Off = 25 ms. Instant response to DMX

variation.

20 = 250 ms. Smooth response to DMX

variation.

COMPRESSION

This menu allows to select between

Linear current output or Quadratic

current output for LEDs

Default = Quadratic

SYNC

This menu allows to adjust the PWM

frequency value (Hz) in order to reduce

flickering in the process of your camera

recordings

BOOST DRIVING

This menu allow to increase the LED’s

current from Min to Max

Linear = Linear

Current output

Quadratic =

Linear light

output

Default = 0

Default = 100

Range = Off-20

Default = 4

Range =

610 Hz – 10 KHz

Default = 610 Hz

Boost mode

activated

Boost mode

deactivated

MENU

Up-Down Up-DownENTER

ENTER

INFRARED MODE

Infrared remote control.

By activating Ir Mode, it will be

possible to navigate trought the unit

functions by using the D.T.S.

infrared remote control

(D.T.S. Code: 0514L008)

Note:

External infrared remote sensor

needed (D.T.S. Code: 03.LA.016)

NOT IMPLEMENTED ON SCENA COMPACT LED 50

DIMMER

Dimmer intensity level (range 0-255)

Active only if MODE = 1 DMX channel mode

12

MENU Up-Down

Up-DownENTER

ENTER

WIRELESS DMX

Wireless DMX enabled / disabled.

By activating WDMX MODE, it will be

possible to control SCENA COMPACT

LED 50via D.T.S. ANTENNA Wireless

DMX Transmitter (cod. 03.E1271).

Active only on SCENA COMPACT

LED 50 with Wireless on board

Wireless

Enabled

Wireless

Disabled

UNLINK = LOG OUT

Logging on SCENA COMPACT LED 50 (WIRELESS DMX must be enabled on SCENA COMPACT LED 50

unit)

To log on the SCENA COMPACT LED 50 in the WIRELESS system simply press and quickly release the

function button on the transmitter.

The transmitter will start flashing rapidly red/green scanning for new free receivers / SCENA COMPACT LED

50 units. When a SCENA COMPACT LED 50 logs on to the transmitter the LINK green light on transmitter

starts to flash rapidly.

After approximately 10 seconds the transmitter will jump back to normal mode and continue transmitting data.

The SCENA COMPACT LED 50 now try to synchronize to the transmitter.

When synchronized to the transmitter, 2 different modes are possible:

1. Antenna transmitter has detected and transmits a DMX signal, in this mode a solid green light is seen on the

transmitter and solid display is seen on SCENA COMPACT LED 50.

2. No DMX signal connected, the Antenna transmitter will flash red/green; display blinking on SCENA

COMPACT LED 50.

To log SCENA COMPACT LED 50 off from a transmitter simply select UNLINK function under

WIRELESS DMX MENU and press ENTER.

When SCENA COMPACT LED 50 is logged off, the display is blinking, meaning its available for log in on a

new transmitter.

Logging out a SCENA COMPACT LED 50

Select UNLINK function under WIRELESS DMX MENU and press ENTER.

When SCENA COMPACT LED 50 is logged off the display is blinking, meaning its available for log in on a

new transmitter.

Logging out all SCENA COMPACT LED 50 units linked to a transmitter

Press and hold the function button of the transmitter for about 3 seconds. When the display is blinking on

SCENA COMPACT LED 50, it mean that the units are logged out.

Transmitter, Status LED

Flashing red/green, no dmx connected.

Solid green, dmx signal detected and transmitted.

Fast flashing red/green, log in mode (every free SCENA COMPACT LED 50 unit, not logged in to any other

transmitter, will be logged on)

SCENA COMPACT LED 50 Status

Display blinking = not logged on to a transmitter (free).

Solid display = logged on to a transmitter and receiving dmx data.

13

MENU Up-Down

Up-DownENTER

ENTER

Up-DownENTER

ENTER

EMERGENCY

Emergency operating mode.

By setting Emergency mode, it

will be possible to select

Dimmer intensity level that will

then ran if DMX signal is

missing or not available.

Usefull for Emergency EXIT

illumination on public areas.

Default = 204 (80%)

ENTERENTER

Up-Down

MENU

ENTERENTER

Up-Down

MENU

.

DEFAULT SETTING

To restore default settings

TEMPERATURE

Internal unit temperature

visualisation

Internal unit temperature

(° Celsius)

LIFE TIME

This menu show the total

unit life time and the

LED life time

SOFTWARE

Software version

Default = OFF

ENTER

Up-DownENTER

Up-Down

MENU

ENTER

Up-Down

MENU

. .

14

11- DMX PROTOCOL

2 CHANNELS MODE (Default)

1 SHUTTER / STROBE

2 DIMMER

DMX CHANNEL

1

Parameter: SHUTTER / STROBE

DMX range

Value

Mid Point

DMX

value

Move Range

(degrees)

Mode

Option

Function

000-009

Black-out

010-019

Open

020-029

Black-out

030-119

Strobe (from 3.27 s to 30 ms)

120-149

Pulse up (from 42.6 s to 120 ms)

150-179

Pulse down (from 42.6 s to 120 ms)

180-204

Random strobe

(Dimmer channel active)

205-229

Full independent Random Strobe

(Dimmer channel disabled)

230-255

Open

DMX CHANNEL

2

Parameter: DIMMER

DMX range

Value

Mid Point

DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional dimmer

1 CHANNEL MODE

1 DIMMER

DMX CHANNEL

1

Parameter: DIMMER

DMX range

Value

Mid Point

DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional dimmer

15

3 CHANNELS MODE

1 SHUTTER / STROBE

2 DIMMER

3 DIMMER FINE

DMX CHANNEL

1

Parameter: SHUTTER / STROBE

DMX range

Value

Mid Point

DMX

value

Move Range

(degrees)

Mode

Option

Function

000-009

Black-out

010-019

Open

020-029

Black-out

030-119

Strobe (from 3.27 s to 30 ms)

120-149

Pulse up (from 42.6 s to 120 ms)

150-179

Pulse down (from 42.6 s to 120 ms)

180-204

Random strobe

(Dimmer channel active)

205-229

Full independent Random Strobe

(Dimmer channel disabled)

230-255

Open

DMX CHANNEL

2

Parameter: DIMMER

DMX range

Value

Mid Point

DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional dimmer

DMX CHANNEL

3

Parameter: DIMMER FINE

DMX range

Value

Mid Point

DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional dimmer

16

The information contained in this publication has been carefully prepared and

checked. However, no responsibility will be taken for any errors. All rights are reserved

and this document cannot be copied, photocopied or reproduced, in part or

completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to

any of its products without prior notice. D.T.S. assumes no responsibility for the use or

application of the products or circuits described herein.

D.T.S. Illuminazione s.r.l. – Via Fagnano Selve 10-12-14 47843

Misano Adriatico (RN) Italia

Tel.: +39 0541 611131. Fax + 39 0541 611111

[email protected] www.dts-lighting.it

0517I222

MADE IN ITALY

ISO 9001:2008

D.T.S. quality system

is certified to the

ISO 9001:2008 standard

D.T.S. products are designed

and manufactured at the D.T.S.

plants in italy

*0517I222*

DTS SCENA COMPACT LED 50 Manuale utente

DTS SCENA COMPACT LED 50 Manuale utente

in altre lingue

Documenti correlati