DTS Wonder S Manuale utente

D.T.S. Illuminazione s.r.l.

Via Fagnano Selve 10/12/14

47843 Misano Adriatico (RN) ITALIA Tel +39 0541 611131 Fax +39 0541 611111 info@dts-lighting.it http://www.dts-lighting.it

Made in Italy

User’s Manual rel 1.0 GB

2

Le informazioni contenute in questo documento sono state attentamente redatte e

controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.

Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato,

riprodotto per intero o in parte senza previo consenso scritto della D.T.S .

D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche

estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna

responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and

checked. However, no responsibility will be taken for any errors. All rights are

reserved and this document cannot be copied, photocopied or reproduced, in part or

completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to

any of its products without prior notice. D.T.S. assumes no responsibility for the use or

application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées

avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas

photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement

préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,

fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline

toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits

décrits.

Las informaciones contenidas en este documento han sido cuidadosamente

redactadas y controladas. Con todo, no se asume ninguna responsabilidad por

eventuales inexactitudes. Todos los derechos han sido reservados y este documento

no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa

autorización escrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de

carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los

productos o de los circuitos descritos.

3

INDEX:

1 - SYMBOLS........................................................................................................................... 4

2 - GENERAL WARNING......................................................................................................... 5

3 - GENERAL WARRANTY CONDITIONS .............................................................................. 5

4 - TECHNICAL FEATURES .................................................................................................... 5

5 - ACCESSORIES .................................................................................................................. 7

6 - IMPORTANT SAFETY INFORMATION .............................................................................. 8

6.1 Fire prevention ............................................................................................................... 8

6.2 Prevention of electric shock ........................................................................................... 8

6.3 Safety ............................................................................................................................ 8

6.4 Level of protection against the penetration of solid and liquid objects ............................ 8

6.5 Long-life auto-charging buffer battery ............................................................................ 8

7 - VOLTAGE AND FREQUENCY ........................................................................................... 9

8 - INSTALLATION .................................................................................................................. 9

8.1 Safety cable ................................................................................................................. 10

8.2 Protection against liquids ............................................................................................. 10

8.3 Movement .................................................................................................................... 11

8.4 Risk of fire .................................................................................................................... 11

8.5 Forced ventilation ........................................................................................................ 11

8.6 Ambient temperature ................................................................................................... 11

9 - MAINS CONNECTION ...................................................................................................... 12

9.1 Protection .................................................................................................................... 12

10 - DMX SIGNAL CONNECTION ......................................................................................... 13

10.1 DMX addresses ....................................................................................................... 13

10.2 Selecting the DMX address ...................................................................................... 13

11 - FIRMWARE UPDATING ................................................................................................ 14

12 - DISPLAY FUNCTIONS .................................................................................................. 15

13 - PERIODIC CLEANING .................................................................................................... 19

13.1 Front lenses screen glass ........................................................................................ 19

13.2 Fans and air passages ............................................................................................. 19

14 - PERIODIC CONTROLS ................................................................................................. 19

15 - DMX PROTOCOL ........................................................................................................... 21

4

1- SYMBOLS

Graphic symbols used on this manual:

THIS SYMBOL INDICATES A HOT SURFACE

Never handle the unit until at least 10 minutes have

elapsed since the projector was turned off.

THIS SYMBOL INDICATES TEMPERATURE

OF THE EXTERNAL SURFACE

The maximum temperature that can be reached

on the external surface of the fitting, in a

thermally steady state, is 80°C (176°F).

THIS SYMBOL INDICATES THE

ELECTRIC SHOCK RISK

High voltage is present inside the unit. Unplug the

unit prior to performing any function which

involves touching the inside of the moving head.

THIS SYMBOL INDICATES PROTECTION

AGAINST ELECTRICAL SHOCK

Connection must be made to a power supply system

fitted with efficient earthing (Class I appliance).

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS YOU CAN PLACE THE

UNIT ON NORMALLY FLAMMABLE SURFACES

Suitable for mounting on normally flammable

materials surfaces greater than 200°C with

some combustion time lag.

THIS SYMBOL MEANS

PHOTOBIOLOGICAL SAFETY

Caution: Possibly hazardous optical radiation emitted

from this product. Do not stare at operating light

source. May be harmful to the eyes.

THIS SYMBOL INDICATES THE MINIMUM

DISTANCE FROM ILLUMINATED OBJECTS

LONG-LIFE AUTO-CHARGING BUFFER BATTERY

The projector contains a rechargeable lead-acid or

lithium iron tetraphosphate battery. To preserve the

environment, please dispose the battery at the end

of its life according to the regulation in force.

!

5

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important

information regarding safety during installation, use and maintenance.

The device is not for domestic use and must be installed by a qualified electrician or

experienced person.

Always disconnect the device from the mains before maintenance.

The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing

material defects.

4- TECHNICAL FEATURES

Overview

WONDER S introduces a revolutionary fixture architecture: an exclusive optical

system consisting of two concentric zones, each featuring a different type of lenses.

This new technology achieves an unprecendeted result: the brightest most uniform

wall wash ever seen.

In traditional wash lights, in fact, when the beam is widened to illuminate a larger area,

a darker spot is visible in the center. The exclusive optics of the WONDER S, however

lets you balance the brightness of the entire beam with that of its center, resulting in

unparalleled evenly diffused luminosity.

You can also obtain stunning multicolor projections: WONDER S LED board consists

of four independent zones: a central one, and a ring divided into three distinct

sections. Each of these four areas has individual control of luminosity, colors and

effects: it’s like having four LED fixtures in one.

The unit is also available as WONDER D, offering an exclusive double concentric

optical system featuring different lenses and linear zoom ranges (central: 3.5° - 52°

zoom; ring: 8° - 52° zoom).

This revolutionary configuration results in an unprecendented evenly diffused

luminosity, size and color.

WONDER D can create amazing concentric multi-color beams and effects in the air,

guaranteed to astonish any audience. Also, WONDER D comes equipped with the

‘FPR’ system (D.T.S. patent), which allows limitless pan rotation, in either direction,

never having to reverse motion.

WONDER S FC

(D.T.S. Product Code: 03.LDR014.F)

• Electronic ballast 90-260Vac 50-60 Hz • Black finish

WONDER D FPR FC

(D.T.S. Product Code: 03.LDR013.FFP)

• Electronic ballast 90-260Vac 50-60 Hz • FPR (Free Pan Rotation) • Black finish

6

4- TECHNICAL FEATURES

LED Technology

49 FULL COLOUR LEDs (RGBW)

Optical group

WONDER S:

7 x 3.5° lenses; 42 x 8° lenses

3.5° - 52° long excursion high-efficiency linear motorized zoom

22.000 Lux / 5 m

WONDER D:

2 concentric independent high efficiency optical groups

Optical group 1 (7 lenses): 3.5° - 52° long excursion linear motorized zoom

Optical group 2 (42 lenses): 8°- 52° long excursion linear motorized zoom

22.000 Lux / 5 m

Color generation

4 discrete LED areas; each area is independently controllable (luminosity, colors,

effects) 16 million colors each

Wide palette of pure uniform whites with variable linear color temperature (2700K –

8000K)

Interface / Control / Programming

LCD graphic display + 4 soft-keys (control / management of the main parameters)

Long-life auto-charging buffer battery

RDM

ARTNET ready

Wireless ready

Updatable internal operating system

Li-Fe display backup battery (WONDER D)

DMX channels

34 ch (Default) or 38 ch

Pan & Tilt

WONDER S:

Pan 540°: 2.5 sec.; Tilt 270°: 1.5 sec

WONDER D:

‘FPR’ system (D.T.S. patent)

Pan: limitless rotation, in both directions; 360° rotation in 1.56 sec.; Tilt 270°: 1.5 sec.

Tri-phase stepper motor technology for ultra-fast silent movements

16-bit resolution

Selectable speed ranges

Pan / Tilt lock

Power supply

Electronic full-range 90-260Vac 50-60 Hz

Power consumption: 850W

Connection

DMX: 4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik

Power supply: POWERCON IN and OUT (re-launch) connectors by Neutrik

7

Operating ambient temperature

-10° / 40°

Weight

22 Kg

International certifications

Certification CE; LED Class: Class 2 LED product

DIMENSIONS

Packaging Dimensions (LxWxH)

610 x 410 x 695 mm

Weight: 27 Kg

5- ACCESSORIES

As standard

* 1 x POWERCON male cable connector (Code 0520P014)

* 1 x XLR 5 Pins male cable connector (Code 0508B066)

* 1 x XLR 5 Pins female cable connector (Code 0508B065)

* 2 x Omega clamp with “Fast Lock” connection 1/4 turn (Code 02K00549)

* User’s manual

Optional (on request)

• “C” Clamp G100 black / professional (max. load 200Kg) (Code 0521A015)

• Aliscaf Clamp (max. capacity load 100Kg) (Code 0521A008)

• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (Code

0521A010)

8

6- IMPORTANT SAFETY INFORMATION

6.1 Fire prevention:

-It is permissible to place the unit on normally flammable surfaces.

Suitable for mounting on normally flammable materials surfaces greater than 200°C

with some combustion time lag.

-Minimum distance from the closest illuminable surface: 0,5 m.

-Replace any blown or damaged fuses only with those of identical value (10AT).

Refer to the wiring diagram if there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

It is, moreover, recommended to protect the supply lines of the projectors from

indirect contact and/or shorting to earth by using appropriately sized residual current

devices.

6.2 Prevention of electric shock:

-High voltage is present inside the unit.

Unplug the unit prior to performing any function which involves touching the inside of

the moving head.

-The level of technology inherent in the WONDER requires the assistance of

specialised personnel for all servicing.

Please refer to an authorised D.T.S. service centre.

-Connection must be made to a power supply system fitted with efficient earthing

(Class I appliance).

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

6.3 Safety:

-The projector should always be installed with bolts, clamps and other tools that are

capable of supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the

failure of the main fixing point.

-The maximum temperature that can be reached on the external surface of the fitting,

in a thermally steady state, is 80°C (176°F).

Never handle the unit until at least 10 minutes have elapsed since the projector

was turned off.

-Never install the fixture in an enclosed area lacking sufficient air flow.

The ambient temperature should not exceed 40°C.

-Caution: Possibly hazardous optical radiation emitted from this product.

Do not stare at operating light source. May be harmful to the eyes.

6.4 Level of protection against the penetration of solid and liquid objects:

-The projector is classified as an ordinary appliance and its protection level

against the penetration of solid and liquid objects is IP20.

6.5 Long-life auto-charging buffer battery:

-The projector contains a rechargeable lead-acid or lithium iron tetraphosphate

battery. To preserve the environment, please dispose the battery at the end

of its life according to the regulation in force.

!

9

7- VOLTAGE AND FREQUENCY

The WONDER with electronic ballast can operate at 90-260Vac 50-60 Hz.

8- INSTALLATION

WONDER may be either floor or ceiling mounted.

For floor mounting installations, the WONDER is

supplied with four rubber mounting feet on the

base. For ceiling mounted installations, we

reccomend the use of appropriate clamps to fix

the unit to the mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the

weight of the unit, as should any clamps used to hang it.

The structure should also be sufficiently rigid so as not to move or shake whilst the

WONDER is moving.

Four 1/4 turn Fast Locks connections placed in the base of the unit allow to hang the

WONDER by using the two omega clamps (provided in the box) in conjunction with

fixing clamps for truss (fixing clamps are not included into the unit box).

10

8.1- Safety cable

We recommend the use of a safety cable or chain connected to the WONDER and to

the suspension truss in order to avoid the fixture accidentally falling should the main

fixing point fail.

Make sure that the iron cable or chain can bear the weight of the entire unit.

You may attach the safety chain/cord to the attachment point (A) located on the base

of the fixture, as shown in the picture below.

8.2 Protection against liquids

The projector contains electric and electronic components which should under no

circumstances come into contact with oil, water or any other liquid.

The proper unit functioning would be compromised should this occur.

!

11

8.3- Movement

Unlimited Pan rotation; Tilt 270° (1,5 sec.) .

Do not place any obstructions in the path of the projector's movement.

WARNING

Do not place any object in the

path of the projector’s

movement

Free Pan Rotation (‘FPR’)

8.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place.

It is permissible to place the unit on normally flammable surfaces. Suitable for

mounting on normally flammable materials surfaces greater than 200°C with

some combustion time lag.

Minimum distance from the closest illuminable surface: 0,5 m.

8.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans

located on both the base and head of the fixture.

These should, under no circumstances, be blocked or obstructed whilst the projector

is in operation. Doing so could cause the fixture to seriously overheat thereby

compromising its proper operation.

8.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow.

The ambient temperature should NOT exceed 40°C.

!

12

9- MAINS CONNECTION

WONDER with electronic ballast operates at 90-260V 50-60 Hz.

Prior to connecting the unit to your mains supply, ensure that the model in your

possession correctly matches the mains supply available.

For connection purposes, ensure that your plug is capable of supporting 4 amps

at 230 VOLT, or 10 amps at 90 VOLT each unit connected.

Strict adherence to regulatory norms is strongly recommended.

MAINS AC OUTPUT 90-260V 50/60 Hz (16A Max)

Max 4 WONDER Units @ 230V

Max 2 WONDER Units @ 120V

MAINS AC INPUT 90-260V 50/60 Hz

FUSE 10A T

9.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each WONDER.

It is, moreover, recommended to protect the supply lines of the projectors by using

Appropriately sized residual current devices.

Connection must be made to a power supply system fitted with efficient earthing

(Class I appliance). A good earth connection is essential for the correct operation

of the projector.

!

13

10- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 signal.

Connection between the mixer and the projector or between projectors must be carried

out using a two pair screened ø 0.5 mm cable and a XLR 5 or 3 pins connector.

Ensure that the conductors do not touch each other.

Do not connect the cable ground to the XLR chassy.

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector

plug and connect it to the next projector by connecting the DMX OUT plug on the first

projector to the DMX IN plug of the second one.

This way, all the projectors are cascade connected.

NB. If the display showing the DMX address flashes, then one of the following errors

has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest

to use a DMX terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of

the DMX line.

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

14

10.1-DMX Addresses

WONDER S / WONDER D can be used in 2 different DMX modes: 34 DMX control

channels (Default) or 38 DMX control channels.

Here below is described the DMX channels addressing for the controller when

WONDER is set to 34 and 38 DMX control channels:

34 channels mode (Default)

Projector 1 A001

Projector 2 A035 If you want to select the next projector, just add “34”

Projector 3 A069

….. A….

projector 6 A171

38 channels mode

Projector 1 A001

Projector 2 A039 If you want to select the next projector, just add “38”

Projector 3 A077

….. A….

projector 6 A191

10.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers

on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop

flashing and the projector is now setted to the new DMX address.

TRICKS:

If you keep pushed the UP or DOWN keys, the channels are calculated more quickly

and you get a faster selection.

11- FIRMWARE UPDATING

To update the software version of the WONDER S / WONDER D you need:

- “D.T.S. Firmware Upgrade Utility” program installed on the PC

- D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008)

- USB-DMX Driver for the D.T.S. RED BOX interface.

- Latest firmware release available for WONDER S / WONDER D unit

Updating the software version.

Please follow the procedure below to perform the update:

1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the

unit software.

2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.

3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.

4. Send the new software version into the unit by using “D.T.S Firmware Upgrade

Utility” program.

15

MENU

ENTER DOWN

UP

DISPLAY

PAN DIRECTION

NORMAL

MENU ENTER DOWN UP

TILT DIRECTION

NORMAL

MENU ENTER DOWN UP

12- DISPLAY FUNCTIONS

DISPLAY FUNCTIONS

The WONDER S / WONDER D display panel shows all the available functions . Using

these functions, it is possible to change some of the parameters and add some

functions. Changing the D.T.S. setting can vary the functions of the unit so that it does

not respond to the DMX 512 used to control it. Carefully follow the instructions below

before carrying out any variations or selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired

function.

Software Version: 10-11-11

Pan Direction

PAN DIRECTION

This menu allows to set

the Pan movement

Normal or Reverse

Tilt Direction

TILT DIRECTION

This menu allows to set

the Tilt movement

Normal or Reverse

Pan Speed

PAN SPEED

Pan Speed control (1-8)

Tilt Speed

TILT SPEED

Tilt Speed control (1-8)

Up-Down

Menu

Up-DownENTER

Up-Down

Menu

Up-Down

Menu

Up-DownENTER

ENTER

Up-Down

Menu

Up-DownENTER

ENTER

Pan movement

Normal or Reverse

Default = Normal

Tilt movement

Normal or Reverse

Default = Normal

Pan Speed control

(1-8)

Default = 8 (Live Mode)

Tilt Speed control

(1-8)

Default = 8 (Live Mode)

MENU ENTER DOWN UP

8

LIVE-TOUR MODE

PAN SPEED

MENU ENTER DOWN UP

8

LIVE-TOUR MODE

TILT SPEED

16

MENU ENTER DOWN UP

ENABLED

BY DMX

RESET

MENU ENTER DOWN UP

34 CHANNELS

DMX MODE

12- DISPLAY FUNCTIONS

Display

DISPLAY FLIP / STAND BY / CONTRAST

Display Flip:

Reverses display's reading depending on

the mounting position

(on the ground or suspended).

Display Standby:

To turn off the display (after 5 seconds)

or leave it always on.

Display Contrast:

Display contrast regulation (1-40)

DMX Mode

DMX MODE

To select DMX mode:

34 channels (Default) or 38 channels

Reset

RESET

Reset via DMX ENABLED / DISABLED

and unit motors reset

Wireless

WIRELESS

Wireless DMX enabled / disabled.

(Wireless module on request)

Up-Down

Menu

Up-DownENTER

ENTER

Up-Down

Menu

Up-DownENTER

ENTER

MENU ENTER DOWN UP

FLIP

ON THE GROUND

DISPLAY

MENU ENTER DOWN UP

FLIP

STANDBY

OFF

DISPLAY

MENU ENTER DOWN UP

FLIP

CONTRAST

25

DISPLAY

Display Flip

ON THE GROUND (Default)

SUSPENDED

Display Standby

OFF = Display Standby

disabled (Default)

ON = Display goes OFF

after 5 seconds

Display Contrast

1-40 (Default = 25)

Up-Down

Menu

Up-DownENTER

DMX Mode

34 channels (Default)

38 channels

ENTER

ENABLED = Reset via

DMX enabled (Default)

DISABLED = Reset via

DMX disabled

NOW = Unit motors reset

Up-Down

Menu

Up-DownENTER

ENTER

ON = Enabled

OFF = Disabled

(Default)

UNLINK = Log out

(Wireless module on

request)

WIRELESS

OFF

MENU ENTER DOWN UP

17

SMOOTH VALUE

Range = 0 – 20

Default = 4

GAMMA CORRECTION

LINE = Linear current output

QUAD = Quadratic light

output (Default)

OUTPUT FREQUENCY

Range: 600 Hz – 10 KHz

Default = 600 Hz

BOOST

OFF = 800mA (Default)

ON = 1000mA

SMOOTH

LED

MENU ENTER DOWN UP

4

GAMMA CORR.

LED

MENU ENTER DOWN UP

QUAD

FREQUENCY

LED

MENU ENTER DOWN UP

600 Hz

BOOST

LED

MENU ENTER DOWN UP

OFF

MENU ENTER DOWN UP

LIVE-TOUR

SETTING

LIVE-STUDIO

SYSTEM INFO

UNIT LIFE: 0124H

LED: R10

ZOOM: R11

PT: R11

MODEL: WONDER D FPR

MENU ENTER DOWN UP

RDM: 000009B4

12- DISPLAY FUNCTIONS

LED

SMOOTH: This menu allows to select

the value of the delay (in milliseconds)

for RGBW and Dimmer channels

reaction to DMX or program variation.

4 = 25 ms delay (fast response)

20 = 250 ms delay (slow response)

GAMMA CORRECTION

This menu allows to select between

Linear current output or Quadratic

current output for LEDs.

OUTPUT FREQUENCY

This menu allows to adjust the PWM

frequency value (Hz) in order to reduce

flickering in the process of your camera

recordings.

BOOST

This menu allows to increase the

LEDs current from 800mA to 1000mA.

Live-Studio setting

System Info

Up-Down

Menu

Up-DownENTER

ENTER

SYSTEM INFO

Unit life time; LED Driver,

Zoom and Pan&Tilt PCBs

software version; unit model

and RDM ID

Up-Down

Menu

Up-DownENTER

ENTER

Up-Down

Menu

Up-DownENTER

ENTER

LIVE-TOUR mode = High

fans speed: the LEDs always

work at maximum power

(Default)

STUDIO mode = Low fans

speed for a very low noise

operation

18

REBOOT

MENU ENTER DOWN UP

TEMPERATURE

CENTER: 041°C MAX CURR.

SECTOR 1: 046°C 1000 MA

SECTOR 2: 049°C

SECTOR 3: 048°C

CPU: 049°C

MENU ENTER DOWN UP

LED LIFE HOURS

CENTER S1 S2 S3

R: 0024 0024 0024 0024

G: 0024 0024 0024 0024

B: 0024 0024 0024 0024

W: 0023 0023 0023 0023

MENU ENTER DOWN UP

12- DISPLAY FUNCTIONS

LED Life hours

Temperature

Reserved

RESERVED

000

MENU ENTER DOWN UP

ENTER CODE

PAN LOCK

NO

MENU ENTER DOWN UP

Up-Down

Menu

Up-DownENTER

ENTER

Pan Lock = Lock the Pan

to the desired value

Tilt Lock = Lock the Tilt

to the desired value

Pan Free = Remove power

to Pan motor

Tilt Free = Remove power

to Tilt motor

LOCK DETECTOR

OFF

MENU ENTER DOWN UP

Lock Detector OFF = Default

Lock Detector ON: This function

lets the user to activate the

Lock detector on Pan and Tilt.

When Lock detector is set to

ON, the unit start the Pan&Tilt

motors reset normally, but if for

any reason there is something

blocking the movement for

Pan&Tilt motors during the

initial reset (example unit into

the fly case and power

connected), it automatically will

stop to reset Pan&Tilt motors

after 5 seconds from the startup

and a warning message (Pan

locked-Tilt locked) will appear

on unit display.

Reboot = Unit Reboot without

needing of turning OFF the unit

Exit To Main = Exit from

Reserved menu

RESERVED

(Code = 100)

Pan lock-Tilt lock

Pan free-Tilt free

Lock Detector

Reboot

Exit To Main

Up-Down

Menu

Up-DownENTER

ENTER

Center and sectors LEDs

panels temperatures; CPU

PCB temperature and LEDs

max current value

Up-Down

Menu

Up-DownENTER

ENTER

LED LIFE HOURS:

RGBW LEDs life time

19

12- DISPLAY FUNCTIONS

Demo

Default

DEFAULT

To restore main settings

13- PERIODIC CLEANING

13.1- Front lenses screen glass

The dust can reduce the luminous output substantially.

Regularly clean the front lenses screen glass using a soft cotton cloth, dampened with

a specialist lens cleaning solution.

13.2- Fans and air passages

The fans and air passages must be cleaned approximately every 6 weeks.

This periodic cleaning will depend of course, on the conditions in which the projector is

operating.

Suitable instruments for performing this type of maintenance are a brush and a

common vacuum cleaner or an air compressor.

If necessary, clean the fans and air passages more frequently.

DEFAULT

SURE?

MENU ENTER DOWN UP

RESTORE MAIN SETTINGS

DEFAULT

RESTORE MAIN SETTINGS

MENU ENTER DOWN UP

PRESS ENTER TO CONFORM

PRESS MENU TO CANCEL

Up-Down

Menu

Up-DownENTER

ENTER

Default

To restore main settings

Up-Down

Menu

Up-DownENTER

ENTER

DEMO

Demo games without DMX

controller

Pan, Tilt, Zoom effect, Zoom

speed, Dimmer, Shutter,

LED effect and LED speed

values selectable by user

DIMMER

DEMO

MENU ENTER DOWN UP

255

20

14- PERIODIC CONTROLS

Mechanical parts

Periodically check all mechanical parts, replacing them if necessary.

Electrical components

Check all electrical components for correct earthing and proper

connection of all connectors, refastening if necessary.

Fuse replacement

Locate the fuse, which protects the electronics, in the base of

the WONDER. Using a multimeter, test the condition of the

fuse, replacing it with one of equivalent type (10AT) if necessary.

!

La pagina sta caricando ...

DTS Wonder S Manuale utente

Questo manuale è adatto anche per

DTS Wonder S Manuale utente

in altre lingue

Documenti correlati

Altri documenti