DTS FOS 100 FULL RGBW Manuale utente

Tipo
Manuale utente

Questo manuale è adatto anche per

Made in Italy
FOS 100 POWER SOLO
FOS 100 POWER
User’s Manual rel 1.2 GB
D.T.S. Illuminazione s.r.l. – ITALY
http://www.dts-lighting.it
2
Le informazioni contenute in questo documento sono state attentamente redatte e
controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i
diritti sono riservati e questo documento non può essere copiato, fotocopiato, riprodotto
per intero o in parte senza previo consenso scritto della D.T.S .
D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche
estetiche, funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna
responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked.
However, no responsibility will be taken for any errors. All rights are reserved and this
document cannot be copied, photocopied or reproduced, in part or completely, without
prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any
of its products without prior notice. D.T.S. assumes no responsibility for the use or
application of the products or circuits described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec
le plus grand soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles
inexactitudes. Tous droits réservés. Ce document ne peut être copié, photocopié ou
reproduit, dans sa totalité ou partiellement, sans le consentement préalable de D.T.S.
D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,
fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline toute
responsabilité sur l'utilisation ou sur l'application des produits ou des circuits décrits.
Las informaciones contenidas en este documento han sido cuidadosamente redactadas
y controladas. Con todo, no se asume ninguna responsabilidad por eventuales
inexactitudes. Todos los derechos han sido reservados y este documento no puede ser
copiado, fotocopiado o reproducido, total o parcialmente, sin previa autorización escrita
de D.T.S.
D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de
carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume
responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los productos
o de los circuitos descritos.
3
INDEX:
1- SYMBOLS 4
2- GENERAL WARNING 4
3- GENERAL WARRANTY CONDITION 4
4- TECHNICAL FEATURES 5
5- MAIN ELECTRICAL CHARACTERISTICS 6
6- ACCESSORIES 7
7- IMPORTANT SAFETY INFORMATION 10
7.1 Fire prevention
7.2 Prevention of electric shock
7.3 Safety
8- INPUT / OUTPUT CONNECTIONS 11
9- DMX SIGNAL CONNECTION 13
9.1 DMX Addresses
9.2 Selecting the DMX address
10- FIRMWARE UPDATING 15
11- DISPLAY FUNCTIONS 16
12- SERVICE MENU 20
13- DMX PROTOCOL 22
4
1- SYMBOLS
Graphic symbols used on this manual
THIS SYMBOL INDICATES A HOT SURFACE
THIS SYMBOL INDICATES ELECTRIC SHOCK RISK
THIS SYMBOL INDICATES GENERAL RISK
THIS SYMBOL MEANS “DO NOT PLACE THE UNIT
ON INFLAMMABLE SURFACES”
THIS SYMBOL INDICATES THE MINIMUM
DISTANCE TO BE KEPT BETWEEN THE DEVICE
AND THE LIT OBJECT
2- GENERAL WARNING
Read the instruction contained in this user manual carefully, as they give important
information regarding safety during installation, use and maintenance.
The device is not for domestic use and must be installed by a qualified electrician or
experienced person.
Always disconnect the device from the mains before maintenance.
The device must always be equipped with an efficient ground connection.
3- GENERAL WARRANTY CONDITIONS
The unit is guaranteed for 36 months from the date of purchase against manufacturing
material defects.
F
!
10cm
5
4- TECHNICAL FEATURES
OVERVIEW
FOS 100 POWER is the most powerful model in the FOS line of compact LED bars,
designed for lighting and colouring large surfaces with a homogeneous projection.
FOS 100 POWER is ideal in a variety of applications, either indoor or outdoor, such as:
lighting building facades, monuments, public and commercial spaces; creating uniform
background colours and cycloramas, etc.
FOS 100 POWER is available in two versions.
FOS 100 POWER FULL COLOUR: 24 x Full Colour (RGBW) LEDs;
FOS 100 POWER RGBW: 96 x RGBW LEDs.
Three dedicated lenses sets (Spot, Medium flood, Wide flood) are available for each
model.
LED Technology
FOS 100 POWER FULL COLOUR:
24 x Full Colour (RGBW) LEDs; 7.028 Lux at 3 m;
16 million colours; linear colour temperature 2800°K – 6500°K
FOS 100 POWER RGBW:
96 x RGBW LEDs (24 x Red, 24 x Green, 24 xBlue, 24 x White); 10.528 Lux at 3 m;
16 million colours; linear colour temperature 2800°K – 6500°K
No infrared emission; no ultraviolet emission
LEDs average lifespan: 100.000 hours
Optical group
3 lenses sets available (Spot, Medium flood, Wide flood)
Control
Via any DMX lighting console (FOS 100 POWER SOLO)
Protection
IP65 protection level against the penetration of solids and liquids
Construction
FOS units are made on aluminium and steel
Connections
M16 male connector + cable (length 30 cm) connection system between Power supply
and LED bar (All versions).
POWERCON + XLR 5 poles cable connectors (FOS 100 POWER SOLO IP20);
HARTING 5 poles cable connector (FOS 100 POWER SOLO IP65)
Power supply
Electronic full range power supply AC 90-260V 50 / 60 Hz
Integrated power supply / LED controller (FOS 100 POWER SOLO)
(Z10 POWER IP20 or Z10 POWER IP65);
External dedicated Z40 power supply / LED controller (FOS 100 POWER)
6
Product codes:
03.LB030S.26.FW10 FOS 100 POWER SOLO IP20 FULLWHITE NARROW GREY SILVER
03.LB030S.26.FW25 FOS 100 POWER SOLO IP20 FULLWHITE MEDIUM GREY SILVER
03.LB030S.26.FW40 FOS 100 POWER SOLO IP20 FULLWHITE WIDE GREY SILVER
03.LB030S.FW10 FOS 100 POWER SOLO IP20 FULLWHITE NARROW BLACK
03.LB030S.FW25 FOS 100 POWER SOLO IP20 FULLWHITE MEDIUM BLACK
03.LB030S.FW40 FOS 100 POWER SOLO IP20 FULLWHITE WIDE BLACK
03.LB030S.F10 FOS 100 POWER SOLO IP20 FULLRGBW NARROW BLACK
03.LB030S.F25 FOS 100 POWER SOLO IP20 FULLRGBW MEDIUM BLACK
03.LB030S.F40 FOS 100 POWER SOLO IP20 FULLRGBW WIDE BLACK
03.LB030S.T10 FOS 100 POWER SOLO IP20 RGBW NARROW BLACK
03.LB030S.T25 FOS 100 POWER SOLO IP20 RGBW MEDIUM BLACK
03.LB030S.T40 FOS 100 POWER SOLO IP20 RGBW WIDE BLACK
03.LB031S.26.FW10 FOS 100 POWER SOLO IP65 FULLWHITE NARROW GREY SILVER
03.LB031S.26.FW25 FOS 100 POWER SOLO IP65 FULLWHITE MEDIUM GREY SILVER
03.LB031S.26.FW40 FOS 100 POWER SOLO IP65 FULLWHITE WIDE GREY SILVER
03.LB031S.FW10 FOS 100 POWER SOLO IP65 FULLWHITE NARROW BLACK
03.LB031S.FW25 FOS 100 POWER SOLO IP65 FULLWHITE MEDIUM BLACK
03.LB031S.FW40 FOS 100 POWER SOLO IP65 FULLWHITE WIDE BLACK
03.LB031S.F10 FOS 100 POWER SOLO IP65 FULLRGBW NARROW BLACK
03.LB031S.F25 FOS 100 POWER SOLO IP65 FULLRGBW MEDIUM BLACK
03.LB031S.F40 FOS 100 POWER SOLO IP65 FULLRGBW WIDE BLACK
03.LB031S.T10 FOS 100 POWER SOLO IP65 RGBW NARROW BLACK
03.LB031S.T25 FOS 100 POWER SOLO IP65 RGBW MEDIUM BLACK
03.LB031S.T40 FOS 100 POWER SOLO IP65 RGBW WIDE BLACK
03.LB031.26.FW10 FOS 100 POWER IP65 FULLWHITE NARROW GREY SILVER
03.LB031.26.FW25 FOS 100 POWER IP65 FULLWHITE MEDIUM GREY SILVER
03.LB031.26.FW40 FOS 100 POWER IP65 FULLWHITE WIDE GREY SILVER
03.LB031.FW10 FOS 100 POWER IP65 FULLWHITE NARROW BLACK
03.LB031.FW25 FOS 100 POWER IP65 FULLWHITE MEDIUM BLACK
03.LB031.FW40 FOS 100 POWER IP65 FULLWHITE WIDE BLACK
03.LB031.F10 FOS 100 POWER IP65 FULLRGBW NARROW BLACK
03.LB031.F25 FOS 100 POWER IP65 FULLRGBW MEDIUM BLACK
03.LB031.F40 FOS 100 POWER IP65 FULLRGBW WIDE BLACK
03.LB031.T10 FOS 100 POWER IP65 RGBW NARROW BLACK
03.LB031.T25 FOS 100 POWER IP65 RGBW MEDIUM BLACK
03.LB031.T40 FOS 100 POWER IP65 RGBW WIDE BLACK
5- MAIN ELECTRICAL CHARACTERISTICS (FOS 100 POWER SOLO)
Input Voltage Range : Vin 90 - 260 Vac
Frequency : 50 / 60 Hz
Power Consumption Range : 10 - 200 W
Power Factor (Pf) : 0.95 electronic PFC controller
Efficiency : 90% typical
Control Input:
Control Signal : DMX 512
Dimming System : Constant Current PWM
Address Range : DMX 512 channels addressable by display
7
6- ACCESSORIES
As standard (IP20)
1 x User’s Manual
1 x POWERCON IN male cable connector (FOS 100 POWER SOLO)
(D.T.S. Code: 0520P014)
1 x POWERCON OUT male cable connector (FOS 100 POWER SOLO)
(D.T.S. Code: 0520P029)
1 x XLR 5 poles male cable connector (D.T.S. Code: 0508B028)
1 x XLR 5 poles female cable connector (D.T.S. Code: 0508B027)
1 x Joint/spacer (D.T.S. Code: 00M09519.46 black finish; 00M09519.44 grey finish) with
2 x knobs (D.T.S. Code: 0511P014)
As standard (IP65)
1 x User’s Manual
1 x HARTING 5 poles male cable connector (D.T.S. Code: 02LD0093.1)
1 x Joint/spacer (D.T.S. Code: 00M09519.46 black finish; 00M09519.44 grey finish) with
2 x knobs (D.T.S. Code: 0511P014)
Optional (on request)
Lenses set Spot (FOS 100 POWER FULLCOLOUR) (D.T.S. Code 03.LK.107)
Lenses set Medium flood (FOS 100 POWER FULLCOLOUR) (D.T.S. Code 03.LK.108)
Lenses set Wide flood (FOS 100 POWER FULLCOLOUR) (D.T.S. Code 03.LK.109)
Lenses set Medium flood (FOS 100 POWER RGBW) (D.T.S. Code 03.LK.114)
Lenses set Wide flood (FOS 100 POWER RGBW) (D.T.S. Code 03.LK.115)
G60 ‘’C’’ Clamp (Max. load 50 Kg) *Black (D.T.S. Code 0521A004)
G50 ‘’C’’ Clamp (Max. load 10 Kg) *Black (D.T.S. Code 0521A012)
M16 female (9 poles) cable connector (D.T.S. Code 0508B106)
M16 male (9 poles) cable connector (D.T.S. Code 0508B105)
Z40 Power supply / LED controller (FOS 100 POWER) (D.T.S. Code 03.LA.120)
8
1
6
0
m
m
140 mm
DIMENSIONS
FOS 100 POWER SOLO
Unit Dimensions Packing Dimensions
(LxWxH) (LxWxH)
990 x 100 x 84,5 mm 1060 x 160 x 200 mm
Weight Weight
7 Kg 8,5 Kg
990 mm
100 mm
8
4
,
5
m
m
9
FOS 100 POWER
Unit Dimensions Packing Dimensions
(LxWxH) (LxWxH)
990 x 56 x 84,5 mm 1060 x 160 x 200 mm
Weight Weight
5,5 Kg 7 Kg
1
6
0
m
m
990 mm
56 mm
8
4
,
5
m
m
10
7- IMPORTANT SAFETY INFORMATION
7.1 Fire prevention:
Never locate the fixture on any flammable surface.
Minimum distance from flammable materials: 10 cm.
Minimum distance from the closest illuminable surface: 10 cm.
7.2 Prevention from electric shock:
High voltage is present inside the unit.
Unplug the unit prior to performing any operation which involves touching the inside of
the unit.
This equipment must be grounded, do not connect to non-grounded supplies.
The use of a thermal magnetic circuit breaker is recommended for each FOS 100
POWER SOLO unit.
Use only AC supplies 90-260V, 50 / 60 Hz.
FOS 100 POWER SOLO (IP20) should never be located in position exposed to rain or in
areas of extreme humidity.
A good air ventilation is essential for proper equipment work.
7.3 Safety:
The external surface of the unit may exeed 50°C; never handle the unit until at
least 5 minutes have elapsed since the unit was turned off.
Never install the unit in an enclosed area lacking sufficient air flow.
The ambient temperature should not exeed 40°C and should not be lower than -10°C.
F
!
10cm
11
8- INPUT / OUTPUT CONNECTIONS
FOS 100 POWER SOLO (IP20)
Mains 90-260 V AC
50-60 Hz input Powercon
Female panel connector
DMX IN/OUT
XLR 5 pins Male / Female
Panel Connectors
Mains 90-260 V AC
50-60 Hz output Powercon
Female panel connector
MAX load:
230 V AC
= 10 FOS 100 POWER SOLO
100 V AC = 5 FOS 100 POWER SOLO
M16 LED input
Male cable connector
M16 LED output
Female panel connector
12
FOS 100 POWER (IP65)
M16 LED input
Male cable connector
13
9- DMX SIGNAL CONNECTION (FOS 100 POWER SOLO):
The unit operates using a digital DMX 512 signal.
Connection between the controller and the unit or between units must be carried out
using a two pair screened ø 0.5 mm.
Ensure that the conductors do not touch each other.
Do not connect the cable ground to the DMX connector chassis.
The plug housing must be isolated. Connect the mixer signal to the DMX IN projector
plug and connect it to the next projector by connecting the DMX OUT plug on the first
unit to the DMX IN plug of the second one.
In this way, all the projectors are cascade connected.
If the display showing the DMX address flashes, then one of the following errors has
occurred:
- DMX signal not present
- DMX reception problem
For Installations where long distance DMX cable connections are needed, we suggest to
use a DMX terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between
pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the
DMX line.
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
1
2
3
5
4
OUT
120 ohm
PIN 3
PIN 2
5
3
4 2
1
1=GND
2=DATA-
3=DATA+
CONTROLLER
S TA N D A R D
D M X 5 1 2
UNIT 1
UNIT 2
UNIT 3
14
9.1 DMX addresses
FOS 100 POWER SOLO (all models) can be used in seven different modes: 10 DMX
channels mode (default), 6 DMX channels mode (Shutter + Dimmer + RGBW), WALL
mode (6 DMX channels; for use with DTS Wall mounted DMX controller 0514L007),
M4CH mode (5 DMX channels; Dimmer + RGBW), RGBW mode (4 channels), 1 DMX
channel mode or CUSTOM DMX mode (not yet implemented).
If you want to use the FOS 100 POWER SOLO in 10 channels mode, select the 10 CH
mode from the MODE menu and set the following addresses on the mixer:
Projector 1 A001
Projector 2 A011 If you want to select the next projector, just add “10”
Projector 3 A021
….. A….
projector 6 A051
If you want to use the FOS 100 POWER SOLO in “WALL” mode, select the “WALL”
mode from the MODE menu and set the following addresses on the mixer: (To be used
only with DTS Wall mounted DMX controller 0514L007)
Projector 1 A001
Projector 2 A009
Projector 3 A017
….. A….
projector 6 A041
9.2 Selecting the DMX address
1) Press the UP-DOWN key until you reach the required DMX address. The numbers on
the display will start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing
and the projector is now controlled by the new DMX address.
TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more
quickly and you get a faster selection.
If you want to select the next projector, just add “8”.
DTS Wall mounted DMX controller 0514L007 assign
8 DMX channels per unit even if some channels are
not used
15
10- FIRMWARE UPDATING
Warning:
This procedure require a base knowledge of Windows computer applications.
Please refer to an authorised D.T.S. service centre.
To update the software version of the FOS 100 POWER SOLO you need:
D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008).
USB-DMX Driver for the D.T.S. RED BOX interface.
D.T.S. Firmware upgrade utility program.
(The driver and the installation procedure are available in our web site
www.dts-lighting.it)
Updating the software version.
Please follow the procedure below to perform the update:
1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit
software.
2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.
3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.
4. Download the new software version into the unit by using D.T.S. Firmware upgrade
utility program.
!
16
11- DISPLAY FUNCTIONS
The FOS 100 POWER SOLO display panel shows all the available functions . Using
these functions, it is possible to change some of the parameters and add some
functions. Changing the D.T.S. setting can vary the functions of the unit so that it does
not respond to the DMX 512 signal used to control it. Carefully follow the instructions
below before carrying out any variations or selections.
NOTE: the symbol shows which key has to be pushed to obtain the desired
function.
Software version 4.0.7
DOWN
UP
ENTER
MENU
REVERSE DISPLAY
Reverses display's reading depending
on the mounting position (On the
ground or suspended).
DISPLAY STAND BY
To turn off the display (after 5 seconds)
or leave it always on.
Up
-
Down
MENU
ENTER
Up
-
Down
Up-Down
Up-DownENTER
ENTER
Up-Down
ENTER
6 CHANNELS
Up-Down
ENTER
ENTER
Up-Down
Up-DownENTER
ENTER
Up-Down
ENTER
AUX MODE
Up-Down
Up-Down
ENTER
ENTER
ENTER
ENTER
Show Custom settings
Up-Down
ENTER
Dimmer + RGBA
Up-Down
ENTER
.
ENTER
ENTER
ENTER
ENTER
Up
-
Down
MENU
ENTER
6 CHANNELS
Up
-
Down
Up-Down
ENTER
ENTER
Default DMX Mode = 10 CH
10 CHANNELS
Up-Down
Floor
Position
Suspension
Position
Display
OFF
Display
Always ON
DMX MODE
To select DMX mode : 10 DMX
channels mode (default), 6 DMX
channels mode (Shutter + Dimmer +
RGB), WALL mode (6 DMX channels;
for use with DTS Wall mounted DMX
controller 0514L007), M3CH mode
(4 DMX channels; Dimmer + RGB),
RGB mode (4 channels), 1 DMX
channel mode.
AUX mode let you activate an
external ON -OFF control on IR
connector.
CUSTOM DMX mode let you set the
parameters for Shutter, Dimmer, Red,
Green, Blue, Ctc, Macro and Function
to the desired DMX channels.
(not yet implemented)
MACRO Function enables
channel mapping macro
rainbow effects
STD (default)
Custom mode enabled
Parameters Setting
on Custom Mode
External ON – OFF
control on IR connector
Standard mode
enabled (Default)
Extended mode enabled:
Rainbow effects on MACRO
channel
M4CH(5 CHANNELS)
RGBA(4 CHANNELS)
1 CHANNEL
17
Boost mode activated
Boost mode deactivated
LED
RGBA Min/Max,
Smooth and
Compression levels
values settings
RGBA MINIMUM VALUES
This menu allow to select
the minimum levels for
Red, Green, Blue and
Amber
RGBA MAXIMUM
VALUES
This menu allow to select
the maximum levels for
These settings have priority
on Master Dimmer
SMOOTH VALUE
This menu allow to select the
value
of the delay ( in milliseconds) for
RGB and Dimmer channels
reaction to DMX or Program
variation.
Off=25 ms delay (Fast response)
20=250 ms delay (Slow response)
COMPRESSION
This menu allow to select
between
Linear courrent output or
Quadratic courrent output
for LEDs
Default = Linear
BOOST DRIVING
This menu allow to increase
the LED’s current from
350mA to 500 mA
Range = Off-20
Default = 4
20 = 250 ms
Smooth response to DMX
variation
Off = 25 ms
Instant response to DMX
variation
Linear=Linear
current output
Quadratic=Linear
light output
With BOOST active, the
LED’s current is set to
500mA
(30%more gain).
Default = Activated
Range =
610 Hz -10 KHz
Default = 610
Default=0
Default=100
Default=0
Default=100
Default=0
Default=100
Up
-
Down
MENU
ENTER
Up
-
Down
Up
-
Down
Up
-
Down
ENTER
Up
-
Down
ENTER
ENTER
ENTER
ENTER
ENTER
Up
-
Down
Up
-
D
own
ENTER
ENTER
ENTER
Up
-
Down
Up
-
Down
ENTER
ENTER
Up
-
Down
Up
-
Down
ENTER
ENTER
ENTER
Up
-
Down
Up
-
Down
ENTER
ENTER
Up
-
Down
ENTER
ENTER
Up
-
Down
ENTER
18
AUTOMATIC MODE
Automatic demo game without
DMX controller
ChPr
Chase with 16 steps
previously created in REC
MODE
Speed and Wait time
selectable by user
CUPr
RGB values selectable by
user
Rainbow (rAIn)
Rainbow colours effect.
Speed time selectable by user
CU01-CU16
Color Macros as on DMX
channel 8 (Macro)
WHITE MACROS
16 macros for White color
from 2800 to 6500 ° K
DIMMER
Dimmer level selectable by
user as on DMX channel 2
(Dimmer)
Dimmer level is active for all
the programs and macros
SHUTTER
Shutter level selectable by
user as on DMX channel 1
(Shutter)
Shutter level is active only for
CU01/CU16 and Wh01/Wh16
macros
ESC
Esc from Automatic Mode
Menu
19
u
DMX Recorder Mode
For the programming of ChPr by using a DMX controller, besides the 10 channels necessary to control the unit
a further 3 DMX channels are needed.
So that in RECORDER mode ( via DMX) the unit will need 13 channels to be correctly programmed.
The three new DMX channels are:
- DMX channel 11 = SCENES channel
From 0-10 = no function ( r001)
From 11-255 are displayed the programmable scenes (max 16 scenes from M001 to M0016 )
- DMX channel 12 = EDIT channel:
From 0-19 = no function
From 20-234 the unit runs the configuration given by the received input DMX values.
With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to
record the selected scene.
From 235-255 the unit runs the configuration given by the received input DMX values closing the sequence as
last scene.
With the channel REC it is possible to record the selected scene as last scene.
- DMX channel 13 = RECORDING channel
Records the set scene with a variation between 0 to 255 (the display flashes indicating that the scene has
been recorded).It is advised that you keep the REC channel set to 0 and to run through the 255 only once you
have decided to save the scene. If ChPr is not closed, by indicating the last scene ( Edit channel between 235-
255), in playback mode all 16 scenes will be played through even if not programmed
INFRARED MODE
Infrared remote control.
By activating Ir MODE, it will be possible to navigate
through the unit functions by using the D.T.S. infrared
remote control.
D.T.S. Code :0514L008
ENTER
MENU
Up-Down
ENTER
.
Up-DownENTER
ENTER
ENTER
Default = OFF
Default = White 1
Default = 255
ENTER
Up-Down
ENTER
MENU
Up-Down
ENTER
.
Up-Down
MENU
Up
-
Down
ENTER
Up-DownENTER
MENU Up-Down
ENTER
REC MODE
In DMX Recorder Mode, it is possible to create
and store the scenes of the ChPr by using an
external DMX controller.
The unit must be setted to 10 channels MODE
NOTE:
External infrared remote
sensor needed.
D.T.S. Code :03.LA.016
Up-DownENTERENTER
MENU
Up-Down
ENTER
SLAVE MODE
Slave mode for ChPr program.
All slave units will be synchronised with master unit,
running their own Chpr program.
FAN SPEED CONTROL
Internal Fan Speed control selectable by
user.
Range: OFF - 24 volt Default : 24 volt
EMERGENCY
Emergency operating mode.
By setting Emergency mode, it will be possible to select
one of the 16 preprogrammed WHITE cues that
will then ran if DMX signal is missing or
not available.
Useful for Emergency EXIT illumination on
public areas.
20
12 - SERVICE MENU
For technical personnel only
To operate this menu:
-Connect the unit to the main
-While reset is running, press the MENU and ENTER keys at the same time.
CHANNELS
This menu allow to set 3 channels or 4 channels LEDs output mode
3 LEDs channels output mode = Not Used on FOS 100 POWER SOLO
4 LEDs channels output mode = Default
PRODUCT MODEL SELECTION:
- FOS 100 POWER = Default
- TITAN PLUS = only for TITAN PLUS unit
- DELTA 8= only for DELTA 8 unit
EXIT
Exit from hidden menu.
AUTOMATIC OPERATION (AUTO):
FOS 100 POWER SOLO can work in automatic mode without a DMX controller. First of
all connect the projectors with a DMX cable (picture below). A maximum quantity of 32
slave units can be connected to the same Master unit.
MASTER SLAVE 1 SLAVE 2 SLAVE 32
To activate Auto mode on the first unit, use the menu to run through the different modes
until AUTO appears on the display, and press enter.
Now it is possible to choose between the different pre-programmed games (CUPr-RAIn-
CU01/CU16-Wh01/Wh16) or ChPr which is user programmable through REC mode. To
confirm game activation press ENTER on the selected GAME.
CUPr-RAIn-CU01/CU16-Wh01/Wh16
The first unit that will work as a Master should be placed in Automatic mode (AUTO), the
other units have to be placed 10 channels DMX mode (MODE 10 CH) and the DMX
address should be set at A001. For RaIn (rainbow) game it is possible to select the
speed for the colour changhing (SPEE).
DIMMER function (in AUTOMATIC MODE) is active for all the programs.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

DTS FOS 100 FULL RGBW Manuale utente

Tipo
Manuale utente
Questo manuale è adatto anche per

in altre lingue