Bartscher 101868 Istruzioni per l'uso

Tipo
Istruzioni per l'uso

Questo manuale è adatto anche per

IT
EN
FR
DE
ES
PT
RU
uso e manutenzione
MOD021V09
use and maintenance
emploi et entretien
Benutz und Wartungsanleitung
uso y mantenimiento
uso e manutenção
7-12-18-25-38-50/SN
12-18-25-38-50/FN
12-18-25-38-50/CNS
20-30/LN
использованиe и техобслуживаниe
101868
101869
7-12-18-25-38-50/SN
12-18-25-38-50/FN
12-18-25-38-50/CNS
20-30/LN
SPIRAL KNEADER
CONTENTS
1 GENERAL INFORMATION
Purpose of this manual………………….……….
Manufacturer and machine Identification……....
Kneader description………………………………
Specifications………………………….………….
Instructions –“Digital control” (optional)............
Overall dimensions……………………………….
Safety devices…………………………………….
Safety information………….………………….….
2 INSTALLATION
Packing and unpacking………..…………………
Installation area……….…………………………..
Electric connection…..…………………………...
4
4
5
5
5
6
6
6
7
7
8
3 OPERATION AND CLEANING
Control descriptions……………………………….
Kneader Operation………………………………..
Operation tips.……………………………………..
End-day cleaning…...….………………………….
Removal of the removable parts mod.”CNS”...
Long periods of inactivity……...………………….
4 TROUBLESHOOTING
Foreword….………………………………………..
Troubles, causes and remedies..………………..
ANNEXES
Disposal and recycling
Spare parts catalogue
Electrical wiring diagram
8
8
9
9
9
9
10
10
GENERAL
INFORMATION
1
Purpose of this manual
This manual has been written by the Manufacturer to make an integral part of the machine standard
equipment. During the design and construction phases, special care has been devoted to any aspects which
might endanger the safety and health of the people interacting with the machine. In addition to the applicable
safety legislation, all “good construction practice” rules have been adopted. The purpose of these information
notes is to make machine users aware that special care should be applied to prevent any risks. The biggest
asset to this end, however, is precaution. Safety is also the responsability of all the operators who interact
with the machine. Keep this manual in a suitable place, where it can be conveniently reached for
consultation. In order to highlight some parts of the text, the following symbols have been used:
DANGER – CAUTION: it indicates hazards likely to cause severe injury ; caution is
requested.
INFORMATION: technical indications of special interest.
This manual comes with the following annexes:
- a guarantee certificate containing the guarantee conditions prescribed by the Manufacturer.
- documents certifying compliance with the applicable safety and personal health legislation in force.
To request After-sales service, submit inquiries or dorder spare parts, contact your Authorised dealer.
Manufacturer and machine Identification
Manufacturer Identification
Serial number
Machine model
Specifications
Mark of Compliance
Year of construction
4
GENERAL
INFORMATION
1
Kneader description
The spiral kneader is a machine meant for professional use by bread bakers and pizzerias.
The different versions of the machine (7-12-16-18-25-38-50 Kg. of kneaded product) cater for a vast range of
production needs, allowing various types of dough to be obtained (suitable above all for soft dough for pizza
and bread).
The machine structure has a scratch-proof painted finish which makes for it easy to clean.
It has safety features compliant with the applicable European Directives.
There are 3 kneader models:
Mod.”SN - FN - CNS - LN”:
7/SN (7 Kg. mix capacity) Lever
12/SN – 12/FN – 12/CNS (12 Kg. mix capacity) Lid
20/LN (16 Kg. mix capacity)
18/SN – 18/FN – 18/CNS (18 Kg. mix capacity) Control panel
25/SN – 25/FN – 25/CNS (25 Kg. mix capacity) Pan
30/LN (25 Kg. mix capacity)
38/SN – 38/FN – 38/CNS (38 Kg. mix capacity) Pot flange
50/SN – 50/FN – 50/CNS (50 Kg. mix capacity) Base
The bowl is removable to allow it to be washed in hot running water or a dishawater.
Specifications
Description Unit of measure 7/SN 12/SN 18/SN 25/SN 38/SN 50/SN
Electric power input V Hz Ph
230V 50Hz 1Ph
230/400V 50Hz 3Ph
230/400V
50Hz 3Ph
Power kW (HP) 0.37(0.5) 0.75 (1) 0.75 (1) 1.5 (2) 1.5 (2) 2.2 (3)
Dough per batch kg 7 12 18 25 38 50
Net weight kg 39 58 59 93 105 175
Packaged weight kg 46 65 66 100 112 195
Description Unit of measure 12/CNS-FN 18/CNS-FN 25/CNS-FN 38/CNS-FN 50/CNS-FN
Electric power input V Hz Ph
230V 50Hz 1Ph
230/400V 50Hz 3Ph
230/400V
50Hz 3Ph
Power kW (HP) 0.75 (1) 0.75 (1) 1.5 (2) 1.5 (2) 2.2 (3)
Dough per batch kg 12 18 25 38 50
Net weight kg 65 66 103 115 206
Packaged weight kg 72 73 112 127 230
Noise < 70 dB(A)
Installation On the floor
Description Unit of measure 20/LN 30/LN
Electric power input V Hz Ph
230V 50Hz 1Ph
230/400V 50Hz 3Ph
Power kW (HP) 0.55 0.75 (1)
Dough per batch kg 16 25
Net weight kg 45 69
Packaged weight kg 55 84,4
Noise < 70 dB(A)
Installation On the floor
Instructions –“Digital control” (optional)
Make sure the plug is inserted correctly in the power outlet and press
the “START/STOP” key. The machine will turn on and is ready to use
(the LED next to the key will come on).
To start the machine in “timer” mode, press the key with the clock
symbol twice in succession (the LED next to it will come on) and set the
desired mixing time using the +/- keys.
After setting the desired mixing time (shown on the display) and making
sure that the pot's lid has been lowered down, press the “START/STOP” key to start the machine. The
display will show the countdown of the time set earlier.
If you want to stop the machine to add some ingredients or for any
5
GENERAL
INFORMATION
1
other reason, before lifting the pot's lid, put the machine in standby by pressing the “START/STOP” key
again. This will also stop the timer, which will resume together with the machine only by first lowering the lid
and then pressing the “START/STOP” button again.
Before lifting the pot's lid, put the machine in standby, otherwise the timer will continue the countdown even if
the machine is in standby. When the time is over, the machine will stop.
If you want to work without the timer, press the key with the “hand” symbol (manual) twice. The LED next to it
will come on (it excludes the timer) and by pressing the “START/STOP” key the machine will start in manual
mode.
Once the cycle has ended, press the “START/STOP” key and the machine will stop.
To turn off the display completely, press the “START/STOP” key and hold it for about 3 seconds.
Overall dimensions
mm
A B C
mm
A
BC SN C CNS-FN
7
12
18
20
25
30
38
50
450
450
450
450
550
550
550
600
700
700
700
700
850
850
850
950
720
870
870
870
970
970
970
1150
7
12
18
20
25
30
38
50
280
350
390
390
430
430
480
530
560
650
670
600
730
680
800
910
560
600
600
560
690
660
710
920
\
620
620
\
710
\
730
940
Safety devices
Microswitch: it will stop the machine
when the pan lid is lifted. When the lid
is closed back, restart the machine by
pressing button I
Microswitch: it will stop the machine
when the head is lifted. When the head
is closed back, restart the machine by
pressing button I (only mod.CNS-FN)
Remote control switch: after an
unscheduled power cut, it requests a
specific machine restart control
Sensor: it prevents the machine from
starting if it does not detect the
presence of the pot (CNS mod. only)
Safety information
It is of the greatest importance to carefully read this manual before carrying out installation and use
operations. Consistent compliance with the instructions contained in this manual will guarantee personal
and machine safety.
Do not tamper with the safety devices for any reason.
We recommend that industrial safety regulations issued nationally by the appointed organisms be strictly
respected.
The manufacturer declines all responsability for injures to persons or damages to property, resulting from
failure to comply with these safety rules.
Correct machine setting, lighting and workshop cleanness are pre-conditions for personal safety.
Do not expose the machine to atmospheric agents.
The machine connection and start-up should only be executed by skilled engineers.
Check that the plant mains ratings correspond to the specifications printed on the machine data plate.
Make sure that the machine is connected to a grounding system.
The work area around the machine should always be kept clean and dry.
Wear the work attire prescribed by the industrial accident-prevention regulations.
6
This machine should always be used for its recommended uses ; any other use is deemed improper and
therefore dangerous.
Check the suitability and weight of the products to work ; do not overload the machine to exceed its
capacity.
It is forbidden to introduce any objects, tools or hands in the dangerous parts.
Keep the machine out of children’ s reach.
Unplug the machine from the mains when not in use.
In the event of breakdowns and/or malfunctioning, do not carry out any repair yourselves, apply to your
Authorised dealer.
Order original spare parts only.
Before carrying out machine cleaning, unplug it from the power mains.
Do not clean with high-pressure water jets.
INSTALLATION
2
Packing and unpacking
The machine will come packaged in a carton with foamed
polyester inserts to guarantee perfect safety during transport.
Handle the carton in compliance with the instructions.
Open the carton and make sure that all components are
intact. Keep the carton for any future machine removal.
Remove screws A and lift machine from pallet.
Remove bars B.
Lift the machine according to the instructions and place it
in its selected setting for installation.
Installation area
The selected machine work setting must be sufficiently lit and have an electric power outlet. The worktop must be
sufficiently large, perfectly level and dry. The machine should be installed in non-explosive environments. In any
case, installation should be carried out by taking into account any applicable industrial safety regulations in force.
Environmental Condition Table
Descriptions Values
Working temperature 0÷35 °C (32÷95 °F)
Storage temperature -15 to +65 °C (from –6.8 to +149 °F)
Relative humidity
Maximum 80% at an ambient temperature of 20 °C
Maximum 50% at an ambient temperature of 20÷60 °C
Ambient dust Lower than 0.03 g/m³
7
Electric connection
DANGER – CAUTION: Electric connection to the power
mains should be executed by skilled engineers.
Single-phase Three-phase
connection connection
230V – 1Ph 230/400V – 3Ph
Check for the perfect effeciency of the plant grounding system. Make sure
that the line voltage (V) and frequency (Hz) correspond to the machine
ratings (refer to the machine identification plate and wiring diagram). The
machine comes equipped with an electric cable to which a multipolar plug
should be connected. Plug the machine into a main wall switch with
differential.
Three-phase connection
Start the machine for just a few seconds and check that the beater turns in
the right direction. If this is not the case, disconnect power and exchange
two of the three phase wires in the plug.
OPERATION AND
CLEANING
3
Control descriptions
1) Start button “I”
Press this button to start the machine.The start button will only be enabled
when the lid is down and the pan is in place.
2) Stop button “0”
Press this button to stop the machine.
3) Locking hand lever for the head (only mod.CNS-FN)
Rotate the hand lever to lift the head (clockwise) or to block it (anti-
clockwise). The start button will only be enabled when the head is down and
blocked.
4) Locking flange for the pan (only mod.CNS)
Rotate the flange to lock the pan (anti-clockwise) or to release it
(clockwise).
Kneader Operation
Lift the pan lid and put the required mix ingredients into the pan.
Close the pan lid.
Tighten the locking hand lever of the head for mod.CNS-FN.
Lock the pan by means of the flange below for mod.CNS.
Start the machine by pressing the start button “I”; machine start can only be controlled if the lid is down
and if the pot is blocked on the flange.
After operation completion, press the stop button “0”.
Lift the lid to empty it of the processed product.
After any operation cycle has been completed, wash the pan and spiral by hot water and soap.
Wipe inner face of the lid with a damp sponge.
2-speed version
Lift the pan lid and put the required mix ingredients into the pan.
Close the pan lid.
Tighten the locking hand lever of the head for mod.CNS-FN.
Lock the pan by means of the flange below for mod.CNS.
Rotate the speed selector to position 2.
Start the machine by pressing the start button “I”; machine start can only be controlled if the lid is down
and if the pot is blocked on the flange.
When the dough becomes a rather compact mixture (about 5 minutes later) stop the machine by
pressing the stop button “0” and rotate the speed selector to position 1.
Restart the machine by pressing the start button “I”, until the required consistency is achieved.
After operation completion, press the stop button “0”.
Lift the lid to empty it of the processed product.
After any operation cycle has been completed, wash the pan and spiral by hot water and soap.
Wipe inner face of the lid with a damp sponge.
8
Operation tips
Every litre of the water used for the mix requires about 2Kg. of the flour. The exact quantities will depend on
the type of product to be obtained and the flour being used. The water should always be poured into the pan
before the flour is added.
Capacity production:
Mod.7/SN: Pour 2.5 litres of water into the pan and add 2 Kg. of flour
After 1-2 minutes of kneading, add another 2.5 Kg. of flour.
Mod.12/SN-12/CNS-12/FN: Pour 4 litres of water into the pan and add 4 Kg. of flour
After 1-2 minutes of kneading, add another 4 Kg. of flour.
Mod.18/SN-18/CNS-18/FN: Pour 6 litres of water into the pan and add 6 Kg. of flour
After 1-2 minutes of kneading, add another 6 Kg. of flour.
Mod.20LN: Pour 6 litres of water into the pan and add 6 Kg. of flour
After 1-2 minutes of kneading, add another 4 Kg. of flour.
Mod.25/SN-25/CNS-25/FN 30/LN: Pour 8 litres of water into the pan and add 8 Kg. of flour
After 1-2 minutes of kneading, add another 9 Kg. of flour.
Mod.38/SN-38/CNS-38/FN: Pour 13 litres of water into the pan and add 12 Kg. of flour
After 1-2 minutes of kneading, add another 13 Kg. of flour.
Mod.50/SN-50/CNS-50/FN: Pour 17 litres of water into the pan and add 16 Kg. of flour
After 1-2 minutes of kneading, add another 17 Kg. of flour.
At the end of a work day, unplug the machine from the power mains.
Thoroughly clean the machine using neutral detergents.
Wipe the machine outer parts with a damp sponge.
Do not use steel wool or abrasive cleaning products.
Removal of the removable parts.
Lift the head by rotating anti-clockwise the hand lever (mod.CNS-FN).
For removing the pan rotate the lower
flange clockwise and lift the pan upwards
(mod.CNS).
INFORMATION: Before every operating cycle always check that the removable parts
are well locked to the machine. Lock the pan by rotating anti-clockwise the lower flange.
Long periods of inactivity
If the machine is to be left idle for long periods of time, turn off the main wall switch, thoroughly clean the
machine and cover it with a sheet to protect it from dust.
9
TROUBLESHOOTING
4
Foreword
In the event of breakdowns or malfunctioning, turn off the main wall switch and contact your local Dealer’s
After-sales service. Do not disassemble any internal machine parts.
The Manufacturer declines all responsability for any tampering !
Troubles, causes and remedies
Trouble
Cause Remedy
Main switch is off
Turn the main switch on to “I
The machine will not start
No voltage input to power line
Apply to your local Dealer’s After-sale service
Logic board protective fuse is blown
Apply to your local Dealer’s After-sale service
10
La presenza del bidoncino barrato sulla targhetta dati dell’apparecchiatura indica che essa al termine della propria vita utile dovrà seguire per il
suo smaltimento e riciclaggio quanto previsto dalla Direttiva Europea. La Direttiva prevede la raccolta separata delle apparecchiature elettriche
ed elettroniche attraverso un sistema di raccolta denominato RAEE. All’atto dell’acquisto di un nuovo apparecchio l’utilizzatore è obbligato a non
smaltire l’apparecchio come rifiuto urbano, ma bensì dovrà riconsegnarlo, in ragione di uno contro uno, al rivenditore o distributore. Il rivenditore
provvederà al suo smaltimento seguendo le procedure previste dal sistema di raccolta dei RAEE. Nel caso del solo smaltimento
dell’apparecchiatura, sul territorio italiano, contattare il produttore, il quale fornirà le informazioni adeguate circa lo smaltimento della macchina
presso il centro di raccolta più vicino all’utente. Gli utilizzatori che risiedono al di fuori del territorio italiano dovranno contattare i Ministeri
dell’Ambiente del loro Paese, i quali forniranno le informazioni necessarie ad un corretto smaltimento. Il mancato rispetto delle procedure di
smaltimento può produrre effetti novici a danno dell’ambiente e delle persone. Pertanto lo smaltimento abusivo, totale o parziale, delle
apparecchiature, porterà a sanzioni amministrative da parte delle Autorità Competenti nei riguardi delle utenze negligenti o inadempienti.
The markings illustrated here (barred garbage bin), on the utensil
data plate, indicates that at the end of its working life, the utensil
must be disposed of and recycled according to European Directive.
The Directive provides for the separate collection of electric and
electronic equipment by a collection system called RAEE. Upon
purchasing a new utensil, the user must not dispose of the utensil as
urban waste but must return it, in a one-to-one exchange, to the
dealer or distributor. The dealer may dispose of the utensil following
the procedures set by the RAEE collection system. In the event the
user disposes of the utensil without purchasing a new one, in Italy
contact the manufacturer who will provide suitable information on
machine disposal at the collection centre closest to the user. Users
who do not reside in Italy must contact the Ministry of the
Environment in their countries who will provide information
necessary for correct disposal. Failure to observe the disposal
procedure may cause harmful effects on the environment and
people. Therefore, total or partial illicit utensil disposal by users is
punishable by local authorities.
La présence de ce symbole, comme ci-dessus (poubelle barrée), sur
l’étiquette, indique que l’appareil, au terme de sa durée de vie devra
suivre pour son élimination et son recyclage, les indications prévues à
ce sujet par les Directives Européennes. La Directive prévoit le
ramassage séparé des appareils électriques et électroniques par le biais
d’un système de ramassage appelé RAEE. Au moment de l'achat de
l'appareil l'utilisateur est obligé à ne pas éliminer l'appareil comme
déchets habituels, mais il devra le ramener, en raison d'un échange, au
revendeur ou au distributeur. Le revendeur se fera charge de son
élimination en suivant les procédures prévues par le système de
ramassage.. Dans le cas de l’élimination de l’appareil, sur le territoire
français, contacter le Ministère de l’Environnement ou le revendeur, ce
dernier fournira les informations nécessaires pour l’élimination de
l’appareil auprès du centre de ramassage le plus près. Les utilisateurs
résidents en dehors du territoire italien devront contacter le Ministère de
l’Environnement de leurs Pays, lesquels fourniront les informations
nécessaires pour une correcte élimination. Le non respect des normes
d’élimination peut avoir des effets nocifs sur l'environnement et sur les
personnes. Par conséquent l’élimination abusive, totale ou partielle, des
appareils de la part des utilisateurs, donnera lieu à des sanctions de la
part des Autorités compétentes.
Wenn das hier dargestellte Symbol (durchgestrichene Abfalltonne)
auf dem Typenschild eines Gerätes wiedergegeben ist, bedeutet
dies, dass es am Ende seiner Lebensdauer entsprechend der
europäischen Richtlinie zu entsorgen und wiederzuverwerten ist. Die
Richtlinie sieht eine getrennte Sammlung von Elektro- und
Elektronik-Altgeräten entsprechend dem sogenannten WEEE-System
vor. Beim Kauf eines neuen Geräts verpflichtet sich der Nutzer,
dieses nicht als unsortierten Siedlungsabfall zu entsorgen, sondern
dem Händler oder Verteiler im Verhältnis eins zu eins
zurückzuerstatten. Der Händler sorgt für die Entsorgung des Geräts
unter Einhaltung der vom WEEE-System vorgesehenen
Vorgehensweise. Wenn das Gerät in Italien zu entsorgen ist, den
Hersteller direkt kontakterien. Nutzer außerhalb Italiens erhalten
beim Umweltministerium des jeweiligen Landes Aufschluss über die
zweckmäßige Entsorgung des Geräts. Die Nichteinhaltung der
Entsorgungsvorschriften kann schädliche Auswirkungen zu Lasten
von Mensch und Umwelt mit sich bringen. Deshalb wird die auch nur
teilweise unbefugte Entsorgung der Geräte seitens von Nutzern
durch die zuständigen Behörden mit Bußen bestraft.
La presencia de los símbolos aquí reproducidos (contenedor de basura
tachado), en la placa de datos del aparato, indica al final de su vida útil,
éste deberá ser desguazado y reciclado según cuanto previsto por la
Directiva Europea. La Directiva prevé la recolección separada de los
aparatos eléctricos y electrónicos por medio de un sistema de
recolección denominado RAEE. En el momento de la compra de un
nuevo aparato el usuario está obligado a no eliminar el aparato como
basura urbana, sino que deber entregarlo, como intercambio del nuevo,
al revendedor o distribuidor. El revendedor se encargará de su desguace
siguiendo los procedimientos previstos por el sistema de recolección de
los RAEE. En caso de tratarse de desguace, exclusivamente en el
territorio italiano, contactar el productor, el cual le dará la información
adecuada sobre la eliminación de la máquina en el centro de recolección
más cercano al usuario. Los usuarios que residen fuera del territorio
italiano deberán contactar los Ministerios del Medio ambiente de su país,
los cuales suministrarán la información necesaria para una eliminación
correcta. El no respeto de los procedimientos de eliminación puede
provocar efectos nocivos que dañan el medioambiente y las personas.
Por lo tanto la eliminación clandestina, total o parcial, de los aparatos
por parte de los usuarios, implicará sanciones por parte de las
Autoridades Competentes.
A presença dos símbolos indicados (contentor do lixo barrado) na Наличие данного символа (перечеркнутый мусорный контейнер)
chapa de dados do aparelho, significa que no fim da própria vida útil на паспортной табличке прибора означает, что по завершению
a desactivação e reciclagem deverão ser feitas conforme as своего срока службы прибор подлежит утилизации и переработке
prescrições contidas na Directiva Europeia. A Directiva prevê a в соответствии с европейской директивой. Директива
recolha separada das aparelhagens eléctricas e electrónicas através предусматривает раздельный сбор отработанной электрической
de um sistema de recolha denominado RAEE. No momento da и электронной аппаратуры по системе RAEE. В момент
compra de um novo aparelho, o utilizador é obrigado a não eliminar
o
утилизировать прибор в качестве бытовых отходов, а сдать его
aparelho como lixo urbano, mas deverá entregá-lo, na razão de um (в соотношении один к одному) продавцу или дистрибьютору.
contra um, ao revendedor ou distribuidor. O revendedor ocupar-se-á Продавец должен обеспечить утилизацию прибора в
da sua eliminação seguindo os processos previstos pelo sistema de соответствии с методами, предусмотренными системой RAEE. В
recolha dos RAEE. No caso de eliminação do aparelho no território случае утилизации оборудования на территории Италии
italiano, contacte o produtor, que fornecerá todas as informações обратиться к производителю, который предоставит информацию
necessárias para a eliminação da máquina junto do centro de
recolha
сбора отходов. Пользователи, находящиеся за пределами
mais próximo do utilizador. Os utilizadores que residem fora do Италии, должны обратиться в Министерство по охране
território italiano deverão contactar os Ministérios do Ambiente do окружающей среды своей страны для получения информации о
próprio País, que fornecerão as informações necessárias para uma порядке утилизации. Несоблюдение методов утилизации может
correcta eliminação. A inobservância dos procedimentos de причинить вред окружающей среде и здоровью людей. Ввиду
eliminação pode prejudicar o ambiente e as pessoas. Portanto, a
этого, в случае полного или частичного несоблюдения правил в
области утилизации оборудования пользователь несет
ответственность в соответствии с законом.
eliminação abusiva, total ou parcial, das aparelhagens por parte dos
utilizadores, são objecto de coima por parte das Autoridades
Competentes.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Bartscher 101868 Istruzioni per l'uso

Tipo
Istruzioni per l'uso
Questo manuale è adatto anche per

in altre lingue