APURO FC374-A Manuale utente

Categoria
Friggitrici
Tipo
Manuale utente
Model:
FC374-A / FC375-A / FC376-A / FC377-A
Heavy Duty
Fryer
Instruction manual
2
AU Telephone Helpline: 1300225960
Safety Instructions
• Position on a flat, stable
surface.
• A service agent/qualified
technician should carry out
installation and any repairs if
required. Do not remove any
components on this product.
• Consult Local and National
Standards to comply with the
following:
- Health and Safety at Work
Legislation
- Fire Precautions
- Wiring Regulations
- Building Regulations
• ALWAYS ensure oil levels are
within the ‘MIN’ and ‘MAX
levels. Failure to do so could
result in fire.
• ALWAYS use a suitable
cooking oil.
• ALWAYS remove excess
moisture/water from food
before frying to avoid excess
foaming and spitting of the
oil.
• Change oil regularly. The
flashpoint of oil (the point
at which it ignites) gradually
reduces the more it is used.
• DO NOT cover the oil pan
when frying.
• DO NOT immerse the
appliance in water.
Some surfaces become
hot during operation -
take care when using the
appliance.
• Always switch off and
disconnect the power supply
to the appliance when not in
use.
• Not suitable for outdoor use.
• This appliance must only
be used in accordance with
these instructions and by
persons competent to do so.
• Keep all packaging away
from children. Dispose of
the packaging in accordance
to the regulations of local
authorities.
• If the power cord is
damaged, it must be
replaced by an Apuro agent
or a recommended qualified
technician in order to avoid a
hazard.
• DO NOT use jet/pressure
washers to clean the
appliance.
3
AU
Telephone Helpline: 1300225960
• This appliance is not
intended for use by persons
(including children) with
reduced physical, sensory or
mental capabilities, or lack
of experience or knowledge,
unless they have been given
supervision or instruction
concerning the use of the
appliance by a person
responsible for their safety.
• Children should be
supervised to ensure that
they do not play with the
appliance.
• Apuro recommend that
this appliance should be
periodically tested (at least
annually) by a Competent
Person. Testing should
include, but not be limited
to: Visual Inspection, Polarity
Test, Earth Continuity,
Insulation Continuity and
Functional Testing.
Ensure oil levels are
maintained above the
minimum level. Failing to do so
may result in element failure.
• Apuro recommend that
this product is connected
to a circuit protected by an
appropriate RCD (Residual
Current Device) (for
FC376-A/FC377-A).
Introduction
Please take a few moments to carefully read
through this manual. Correct maintenance and
operation of this machine will provide the best
possible performance from your Apuro product.
These appliances are intended to be used for
commercial applications, for example in kitchens of
restaurants, canteens, hospitals and in commercial
enterprises such as bakeries, butcheries, etc., but
not for continuous mass production of food.
Apuro will not accept liability for product failures in
the event that:
The instructions in this manual have not been
followed correctly.
Unqualified or unauthorized personnel have
adjusted the Fryer.
Non-original spare parts are used.
The Fryer has not been handled and cleaned
correctly.
The Fryer has been used for a purpose for
which it was not intended.
Pack Contents
The following is included:
Apuro fryer
Basket (FC375-A/FC377-A x 2)
Element guard (FC375-A/FC377-A x 2)
Lid (FC375-A/FC377-A x 2)
Instruction manual
Apuro prides itself on quality and service, ensuring
that at the time of packaging the contents are
supplied fully functional and free of damage.
Should you find any damage as a result of transit,
please contact your Apuro dealer immediately.
Installation
Remove the Fryer from the packaging,
ensuring that all protective packaging, plastic
and residues are thoroughly cleaned from its
surfaces.
Place the Fryer on a firm level surface (Or
Fryer stand if purchased).
Before installing and operating the Fryer, it
is the user’s responsibility to ensure that all
Health & Safety regulations concerning safe
positioning, spacing, ventilation, electrical
installation, and fire risk, are complied with.
4
AU Telephone Helpline: 1300225960
Fitting head unit to the Fryer body
1. Position the head unit onto the body of the fryer,
locating it into the hole (A) at the side of the main
body by the pin (B) on the side of the head unit.
2. Rotate the head unit and put spring pin (C) into
the hole (D) ,then it can hold the position if the
appliance is not going to be used.
3. Continue to push spring pin (C) and rotate the head
unit, the element is lowered into the pan and the
head unit is close to the operating position.
4. When the spring pin is put into the hole (E), the
safety switch (F) will work and the appliance will
work.
The fryer can now be filled with the appropriate cooking
oil.
Connect the Fryer to the correct power supply and it is
ready to operate.
Operation
1. Please ensure Oil level is between Min and Max lines.
2. Turn on the power switch. Then turn the thermostat dial to the required temperature setting.
3. Allow time for the oil temperature to reach the required setting. While the oil is heating, the green
light will be on. When the oil has reached the required temperature, the green light will switch off.
4. As the oil temperature fluctuates, the thermostat will operate to maintain the set temperature, the
indicator light will be lit when the Fryer is heating the oil.
5. A temperature setting of between 170°C and 180°C will be sufficient for most cooking. However this
may vary for particular food types or according to individual requirements.
Using the timer
The digital timer with audible alarm can be set from 1 second to 15 minutes. The timer provides an
audible alarm only; after the set time expires unit will continue to operate at set temperature.
START/STOP: Press START/STOP to start timer, press again
to stop. The timer will provide an audible alarm after the
set time. The alarm will beep 10 times and the display will
continue to flash until timer is reset (press the START/STOP
button).
UP: Press UP to add extra time.
DOWN: Press DOWN to reduce time.
PROGRAM: There are a total of 6 programmable timer settings. The default factory program settings
are given below.
Program 1 2 3 4 5 6
Factory preset time 00:30 01:00 01:30 02:00 02:30 03:00
To change the length of a program select the program you want to change by scrolling using the
PROGRAM button.
Adjust the program time by using the UP and DOWN buttons. Press START/STOP to commence the
count-down. The new program time will be automatically stored.
If the unit is left without power for more than 24hrs the timer settings will revert to the factory
defaults.
5
AU
Telephone Helpline: 1300225960
Cleaning, Care & Maintenance
The Fryer should be cleaned after each day’s operation; however it may require cleaning more often,
depending on the volume of frying carried out.
1. Switch off the power and disconnect from the power supply by removing the plug from the socket.
2. The Fryer must be left until the oil has cooled to room temperature before cleaning.
3. Empty oil by opening the drain tap at the front of the unit.
Note: If the oil is to be reused, it should be filtered.
4. Once the oil has been emptied from the fryer, the head unit can be tilted back enabling the pan to be
cleaned using warm soapy water.
Warm soapy water is recommended for cleaning. Cleaning agents after prolonged use can cause damage
to stainless steel.
The main body can also be cleaned with warm soapy water. Remove the head unit and element before
cleaning takes place.
The head unit cannot be immersed in water, but can be wiped down with a damp cloth.
After cleaning as above, please use a dry cloth to clean the appliance to ensure there is no water on the
heating element and in the water oil pan.
Troubleshooting
Fault Probable Cause Solution
Appliance not working Unit not switched on Check the unit is plugged in correctly and
switched on
Lead is damaged Call Apuro agent or qualified Technician
Power supply Check power supply
Appliance does not
reach set temperature
Faulty thermostat Call Apuro agent or qualified technician
Faulty element Call Apuro agent or qualified technician
Build-up of fat on the element Clean the appliance
Appliance heats up but
indicator light not ON
Indicator light has expired Call Apuro agent or qualified technician
Power indicator light
comes on but appliance
does not heat up
Faulty element Call Apuro agent or qualified technician
Faulty thermostat Call Apuro agent or qualified technician
Thermostat set incorrectly Check thermostat
Appliance slow to heat
up
Faulty element Call Apuro agent or qualified technician
Build-up of fat on the element Clean the appliance
No power Thermal cut-out activated Press re-set switch on rear of unit
Technical Specifications
Model Voltage Power Capacity
(Litres)
Max batch
load (kg)
Dimensions
H x W x D mm Weight
FC374-A 220-240V~,
50Hz
2900W 8L 1 440 x 280 x 510 9.5kg
FC375-A 2 x 2900W 2 x 8L 2 x 1 440 x 560 x 510 17.0kg
FC376-A 6000W 8L 1 440 x 280 x 510 10.4kg
FC377-A 2 x 6000W 2 x 8L 2 x 1 440 x 560 x 510 18.8kg
6
AU Telephone Helpline: 1300225960
Electrical Wiring: FC374-A/FC375-A
The plug is to be connected to a suitable mains socket.
This appliance is wired as follows:
Live wire (coloured brown) to terminal marked L
Neutral wire (coloured blue) to terminal marked N
Earth wire (coloured green/yellow) to terminal marked E
This appliance must be earthed.
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency
disconnection being required they must be readily accessible.
Electrical Wiring: FC376-A/FC377-A
FC376-A and FC377-A are supplied unplugged and
require hardwiring to a suitable electrical power
supply capable of supporting 6KW at 220-240V/50hz.
This appliance is wired as follows:
Live wire (coloured brown) to terminal marked L
Neutral wire (coloured blue) to terminal marked N
Earth wire (coloured green/yellow) to terminal
marked E
This appliance must be earthed.
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of
any obstructions. In the event of any emergency
disconnection being required they must be readily
accessible.
Connection to a suitable power supply
should only be carried out by a qualified and
competent electrical engineer.
For FC376-A:
For FC377-A:
7
AU
Telephone Helpline: 1300225960
Compliance
The product must not be disposed of as household waste. To help prevent possible harm to human
health and/or the environment, the product must be disposed of in an approved and environmentally safe
recycling process. For further information on how to dispose of this product correctly, contact the product
supplier, or the local authority responsible for waste disposal in your area.
Apuro parts have undergone strict product testing in order to comply with regulatory
standards and specifications set by international, independent, and federal authorities.
Apuro products have been approved to carry the following symbol:
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, mechanical, photocopying,
recording or otherwise, without the prior written permission of Apuro.
Every effort is made to ensure all details are correct at the time of going to press, however, Apuro reserve the right to change specifications without
notice.
DECLARATION OF CONFORMITY
Conformiteitsverklaring Déclaration de conformité Konformitätserklärung Dichiarazione di conformità
Declaración de conformidad Declaração de conformidade
Equipment Type Uitrustingstype • Type d'équipement Gerätetyp
Tipo di apparecchiatura Tipo de equipo Tipo de equipamento
Model Modèle Modell Modello
Modelo Malli
Single Fryer 1 x 8Ltr 2.9kW with Timer
Double Fryer - 2 x 8Ltr 2.9kW with Timer
Single Fryer 1 x 8Ltr 6kW with Timer
Double Fryer - 2 x 8Ltr 6kW with Timer
FC374-A
FC375-A
FC376-A
FC377-A
Application of Territory Legislation &
Council Directives(s)
Toepassing van Europese Richtlijn(en) •
Application de la/des directive(s) du
Conseil Anwendbare EU-Richtlinie(n) •
Applicazione delle Direttive
• Aplicación de la(s) directiva(s) del
consejo Aplicação de directiva(s) do
Conselho
Electrical safety
AS/NZS 60335.1:2011 +A1:2012 +A2:2014 +A3:2015 +A4:2017
IEC 60335-2-37:2002 +A1:2008 +A2:2011
EN 62233:2008
Electro-Magnetic Compatibility
EN 55014-1:2017
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
Producer Name Naam fabrikant Nom du producteur Name des Herstellers
Nome del produttore Nombre del fabricante Nome do fabricante
Apuro
I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation, Directive(s)
and Standard(s).
Ik, de ondergetekende, verklaar hierbij dat de hierboven gespecificeerde uitrusting goedgekeurd is volgens de bovenstaande
Richtlijn(en) en Standaard(en).
Je soussigné, confirme la conformité de l'équipement cité dans la présente à la / aux Directive(s) et Norme(s) ci-dessus
Ich, der/die Unterzeichnende, erkläre hiermit, dass das oben angegebene Gerät der/den oben angeführten Richtlinie(n) und
Norm(en) entspricht.
Il sottoscritto dichiara che l'apparecchiatura di sopra specificata è conforme alle Direttive e agli Standard sopra riportati.
El abajo firmante declara por la presente que el equipo arriba especificado está en conformidad con la(s) directiva(s) y
estándar(es) arriba mencionadas.
Eu, o abaixo-assinado, declaro que o equipamento anteriormente especificado está em conformidade com a(s) anterior(es)
Directiva(s) e Norma(s)
Date • Data • Date • Datum • Data •
Fecha • Data
21
st
May 2021
Signature Handtekening • Signature
Unterschrift Firma • Firma •
Assinatura
Full Name Volledige naam • Nom et
prénom Vollständiger Name • Nome
completo Nombre completo Nome
por extenso
Ashley Hooper
Position Functie Fonction • Position
Qualifica Posición Função
Technical & Quality Manager
Supplier
Producer Address • Adres fabrikant •
Adresse du producteurAnschrift des
Herstellers • Indirizzo del produttore •
Dirección del fabricante • Morada do
fabricante
Fourth Way,
Avonmouth,
Bristol,
BS11 8TB
United Kingdom
Campbelltown
NSW 2560
DocuSign Envelope ID: AD52F341-7934-46D3-96D3-85DACAA38FF8
FC374-A to FC377-A_A5_v2_20210715
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

APURO FC374-A Manuale utente

Categoria
Friggitrici
Tipo
Manuale utente

in altre lingue