ProLights 28 W track mounted mini LED profile Manuale utente

Marca: ProLights

Modello: 28 W track mounted mini LED profile

Categoria: Stroboscopi

Tipo: Manuale utente

USER MANUAL

MANUALE UTENTE

MINIECLIPSETRWD

MINIECLIPSEWD

EN - IT

MINI LED ELLIPSOIDAL

Optics(not included)

MINIECLIPSEWD

•

MINIECLIPSEWDTU

•

MINIECLIPSEWDDY

MINIECLIPSEL

• MINIECLIPSEL19

• MINIECLIPSEL26

• MINIECLIPSEL36

• MINIECLIPSEL50

Reector Housing

Optics(not included)

MINIECLIPSETRWD

•

MINIECLIPSETRWDTU

•

MINIECLIPSETRWDDY

MINIECLIPSETRL

• MINIECLIPSETRL19

• MINIECLIPSETRL26

• MINIECLIPSETRL36

• MINIECLIPSETRL50

Reector Housing

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.001-11/15

MINIECLIPSEWD - MINIECLIPSETRWD

Packing content

• MINIECLIPSEWD/TRWD

• User manual

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 MINIECLIPSEW Description and specications

1. 2 Technical specications

1. 3 MINIECLIPSETRWD Description and specications

1. 4 Technical specications

1. 5 Conguration MINIECLIPSEWD/TRWD

1. 6 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 Autoshow mode

3. 5 Static mode

3. 6 DMX conguration

3. 7 DMX mode

3. 8 Channels DMX

3. 9 Fixture settings

3. 10 Fixture informations

3. 11 Wireless setting

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Trouble shooting

MINIECLIPSEWD - MINIECLIPSETRWD

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bumps;

- in places with a temperature of over 45 °C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

MINIECLIPSEWD - MINIECLIPSETRWD

- 1 - INTRODUCTION

1.1 MINIECLIPSEWD - DESCRIPTION

MINIECLIPSEWD is a new concept of mini LED ellipsoidal. Showcasing a stylish design, ease of use, precise

optics, sharp image projection and bright even projection all in a compact housing that is just a quarter of

the size of traditional ellipsoidals. MINIECLIPSEWD comes with a built-in Wireless DMX (WDMX) module for

cable-free operation, extending the possible applications of this light. Designed for applications in com-

mercial installtions, museums, restaurant, churches, educational theatres, and any other installation where

size is an important factor. Available in Tungsten and Daylight versions, MINIECLIPSEWD performs even

eld projection, high CRI at any level of brightness and linear dimmer over the entire ramp.

FEATURES:

• Bright, Compact LED Ellipsoidal with sharp optics and wireless DMX control.

• Available with Warm and Cold White High CRI LED sources.

• 19°, 26°, 36° and 50° lens options.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 1x28W CREE LED

• CT: TU 3100 K - DY 6000K

• CRI: TU 93 - DY 91

• Luminous ux: TU 612 lm - DY 700lm

• Lux: TU 880 lux - DY 1037lux @3m - 19°

• Source life expectancy: >50.000 h

OPTICS

• Beam angle: optional 19° / 26° / 36° / 50°

• Lens type: high-quality glass lens optics

DYNAMIC EFFECTS

• Fixed gobos: Gobo Holder Included in optics

• Gobo size: E size, gobo Ø 37.5 mm - img Ø 24 mm - thickness 0.5 mm

• Static colour mode: selection of static colour

• Manual colour mode: manual adjustment of dimmer and strobe

• Auto mode: built-in programs with execution speed adjustment

BODY

• Body: sturdy die-cast aluminium body conceived for long-time durability

• Body colour: black

CONTROL

• Protocols: W-DMX

• DMX channels: 1 / 2 / 5channel

• W-DMX: included, wireless solution receiver

• Display: LCD display

• Firmware upgrade:

ELECTRONICS

• Dimmer: linear 0~100% electronic dimmer

• Dimmer curves: 4 dierent dimming curves available

• Strobe / shutter: 1-25 Hz, electronic

• Operating temperature: -10° ~ +45°

• Flicker: icker free operation

• Selectable PWM: 600~25K Hz

MINIECLIPSEWD - MINIECLIPSETRWD

1.3 MINIECLIPSETRWD - DESCRIPTION

MINIECLIPSETRWD is the track-mounted version of MINIECLIPSE LED ellipsoidal. Featuring elegant white

housing and Wireless onboard DMX allowing the remote control of the luminaire, thus making it an in-

novative and perfect solution for installation in commercial areas, showrooms, museums and churches.

It showcases a stylish design, ease of use, precise optics, sharp image projection and bright at projection

in a compact housing, thus keeping superior brightness and high CRI white reproduction.

FEATURES:

• Track mounted compact LED ellipsoidal with sharp optics and wireless DMX control.

• Available with warm and cool white high CRI LED sources.

• 19°, 26°, 36° and 50° lens options.

1.4 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 1x28W CREE LED

• CT: TU 3100 K - DY 6000K

• CRI: TU 93 - DY 91

• Luminous ux: TU 612 lm - DY 700lm

• Lux: TU 880 lux - DY 1037lux @3m - 19°

• Source life expectancy: >50.000 h

OPTICS

• Beam angle: optional 19° / 26° / 36° / 50°

MINIECLIPSEWD

Fig.1 - Technical drawing

226226

112

202

226226

112

252

ELECTRICAL

• Power supply: 100-240V – 50/60Hz

• Power consumption (at 230V): 29W

PHYSICAL

• Cooling: natural cooling of the peculiar chassis and to absence of fans

• Power connection: moulded IP power IN connector

• IP rating: 20

• Dimensions (WxHxD): 112x202x226mm

• Weight: 1.5kg

MINIECLIPSEWD - MINIECLIPSETRWD

• Lens type: high-quality glass lens optics

DYNAMIC EFFECTS

• Fixed gobos: Gobo Holder Included in optics

• Gobo size: E size, gobo Ø 37.5 mm - img Ø 24 mm - thickness 0.5 mm

• Static colour mode:

• Manual colour mode: manual adjustment of dimmer and strobe

• Auto mode:

BODY

• Body: sturdy die-cast aluminium body conceived for long-time durability

• Body colour: white

CONTROL

• Protocols: W-DMX

• DMX channels: 1 / 2 / 5channel

• W-DMX: included, wireless solution receiver

• Display: LCD display

• Firmware upgrade: yes, via USB-DMX interface (UPBOX1) not included

ELECTRONICS

• Dimmer: linear 0~100% electronic dimmer

• Dimmer curves: 4 dierent dimming curves available

• Strobe / shutter: 1-25 Hz, electronic

• Operating temperature: -10° ~ +45°

• Flicker: icker free operation

• Selectable PWM: 600~25K Hz

ELECTRICAL

• Power supply: 100-240V – 50/60Hz

• Power consumption (at 230V): 29W

PHYSICAL

• Cooling: natural cooling of the peculiar chassis and to absence of fans

• Sospension and xing: track-adapter included for suspension and xing

• Power connection: moulded IP power IN connector

• IP rating: 20

• Dimensions (WxHxD): 112x252x226mm

• Weight: 1.7kg

Fig.2 - Technical drawing

MINIECLIPSETR

226226

112

202

226226

112

252

MINIECLIPSEWD - MINIECLIPSETRWD

1.5 THE CONFIGURATIONS MINIECLIPSEWD/TRWD

Conﬁgurations

MINIECLIPSEWD/TRWDTU

Reector Housing

Versione Tungsten

Temp. colore: 3100K

MINIECLIPSEWD/TRWDDY

Reector Housing

Versione Daylight

Temp. colore: 6000K

MINIECLIPSE/TRL19

Ottica per sagomatore

MINIECLIPSEWD/TRWD,

angolo 19°

MINIECLIPSE/TRL26

Ottica per sagomatore

MINIECLIPSEWD/TRWD,

angolo 26°

Illuminance at a Distance

19°

1.0m

3.0m

5.0m

7.0m

10.0m

0.33m

1.00m

1.67m

2.34m

Lux Center Beam Angle: 19° Beam Width

9333lx

1037lx

373lx

190.5lx

3.17m94lx

MINIECLIPSEWD/TRWD DY(19°)

Illuminance at a Distance

26°

1.0m

3.0m

5.0m

7.0m

10.0m

0.46m

1.39m

2.31m

3.23m

Lux Center Beam Angle: 26° Beam Width

5040lx

560lx

202lx

103lx

4.62m51lx

MINIECLIPSEWD/TRWD DY(26°)

Illuminance at a Distance

19°

1.0m

3.0m

5.0m

7.0m

10.0m

0.33m

1.00m

1.67m

2.34m

Lux Center Beam Angle: 19° Beam Width

7920lx

880lx

316lx

161lx

3.17m80lx

MINIECLIPSEWD/TRWD TU(19°)

Illuminance at a Distance

26°

1.0m

3.0m

5.0m

7.0m

10.0m

0.46m

1.39m

2.31m

3.23m

Lux Center Beam Angle: 26° Beam Width

4626lx

514lx

185lx

94lx

4.62m46lx

MINIECLIPSEWD/TRWD TU(26°)

MINIECLIPSEWD - MINIECLIPSETRWD

MINIECLIPSE/TRL36

Ottica per sagomatore

MINIECLIPSEWD/TRWD,

angolo 36°

MINIECLIPSE/TRL50

Ottica per sagomatore

MINIECLIPSEWD/TRWD,

angolo 50°

Illuminance at a Distance

36°

1.0m

3.0m

5.0m

7.0m

10.0m

0.65m

1.95m

3.25m

4.55m

Lux Center Beam Angle: 36° Beam Width

2925lx

325lx

117lx

60lx

6.5m29lx

MINIECLIPSEWD/TRWD D

Y(36°)

lluminan

ce at a Distance

50°

1.0m

3.0m

5.0m

7.0m

10.0m

0.93m

2.80m

4.65m

6.53m

Lux Center Beam Angle: 50° Beam Width

27405lx

3045lx

1096lx

559lx

9.19m274lx

MINIECLIPSEWD/TRWD DY(50°)

Illuminance at a Distance

36°

1.0m

3.0m

5.0m

7.0m

10.0m

0.46m

1.39m

2.31m

3.23m

Lux Center Beam Angle: 36° Beam Width

2547lx

283lx

102lx

52lx

4.62m26lx

MINIECLIPSEWD/TRWD TU(36°)

lluminan

ce at a Distance

50°

1.0m

3.0m

5.0m

7.0m

10.0m

0.93m

2.80m

4.65m

6.53m

Lux Center Beam Angle: 50° Beam Width

1440lx

160lx

58lx

30lx

9.19m14.5lx

MINIECLIPSEWD/TRWD TU(50°)

MINIECLIPSETRWD

MINIECLIPSEWD

Fig.3

MINIECLIPSEWD - MINIECLIPSETRWD

1.6 OPERATING ELEMENTS AND CONNECTIONS

1. MINIECLIPSEWD/MINIECLIPSETRWD

2. LOCKING KNOB for optics proler

3. SAFETY EYE to attach safety cable.

4. ROTARY ARM

5. DIMMER KNOB for brightness adjustment

6. MINIECLIPSEL/MINIECLIPSETRL optics proler

7. FOCUS AND ZOOM ADJUSTING SCREW to

zoom the projected image clearly

8. SHUTTER

9. GOBO HOUSING

10. SCREW to regolate housing gobos

11. CONTROL PANEL with display and 4 buttons

used to access the control panel functions and

manage them

12. TRACK-ADAPTER

Fig.4

MINIECLIPSEWD - MINIECLIPSETRWD

- 2 - INSTALLATION

2.1 MOUNTING

MINIECLIPSEWD/MINIECLIPSETRWD is designed for applications in exhibition areas, commercial spaces,

museums, restaurant, churches, and any other installation where size is an important factor. For xing, sta-

ble mounting clips are required. The mounting place must be of sucient stability and be able to support

a weight of 10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the xture’s being used.

• Install the projector at a suitable location.

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm. The

adjust the projector and use the knobs.

NOTE - For the installation of the MINIECLIPSETRWD make sure that the ridge of the adaptor is in with the

groove of the track. Turn knobs 90° to connect the adaptor to the circuit. Please see the gure 4.

MINIECLIPSEWD - MINIECLIPSETRWD

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

To turn on the MINIECLIPSEWD connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then

the unit is ready for operation. You can also adjust the dimmer and zoom using the knobs.

To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and o via a light switch.

NOTE - To operate the projector MINIECLIPSETRWD you need a system track. The track system must be in-

stalled and maintained by a suitably qualied person in compliance with latest construction and relevant

legislation. It is the responsibility of the installer to ensure the electrical, mechanical and thermal com-

patibility of the track system and the ttings. The connection to the main network of electric distribution

must be carried out by a qualied electrical installer.

ATTENTION - Mains voltage must be switched o before mounting; maintenance; insert and replace

Adaptors; spots and luminaires.

3.2 BASIC

Access control panel functions using the four panel buttons located directly underneath the LED Display

(g.3).

UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in a

function

Used to select and store the

current menu or conrm the

current function value or

option within a menu

MENU UP DOWN ENTER

Fig.5- Functions of the buttons

MINIECLIPSEWD - MINIECLIPSETRWD

3.3 MENU STRUCTURE

MENU (LEVEL 1) (LEVEL 2) (LEVEL 3) REMARK

1 Auto Show Auto Show Speed

< Auto 1 > < 100 > Default: Auto 1; Speed:100

< Auto 2 > < 100 >

< Auto 3 > < 100 >

< Auto 4 > < 100 >

2 Static Dimmer 255 Default: 255

Strobe 0 Default: 0

3 Dimmer Mode < O > O: Dimmer speed On/O

<Dimmer1> DIM 1: Dimmer speed fast 0.8 s

<Dimmer2> DIM 2: Dimmer speed middle 1.6 s

<Dimmer3> DIM 3: Dimmer speed slow 2.4 s

4 Back Light < On > Default: On

< 10 s > 10 s: O after 10 seconds

< 20 s > 20 s: O after 20 seconds

< 30 s > 30 s: O after 30 seconds

5 Information Fixture Hours < 9999H>

Version < V1.0 >

6 DMX Address < 001 > Default 001

7 DMX Channel < 1 Ch > Default 5CH

< 2 Ch >

< 5 Ch >

8 Master/Slave Master Default: Slave

Slave

9 Wireless Setting Receive Setting < On > Default: O

< O>

Receive Reset < No >

< Yes >

3.4 AUTO SHOW MODE

If no DMX control signal is present at the DMX INPUT, the unit independently runs through its show pro-

gramme provided that the blackout mode is switched o:

• Press the button MENU so many times until the display shows AUTO, then press the button ENTER.

• Press the button UP/DOWN to switch between the show AUTO 1 - AUTO 4. The unit will operate in show

mode.

• Using the button UP/DOWN to select the desired run speed slow-fast (0-100)

• Press the button ENTER to save the setting.

IMPORTANT: Programs AUTO 1 - AUTO 4 are fully pre-programmed and will not be altered by changes.

NOTE - To deactivate AUTOSHOW mode, activate SLAVE function.

MINIECLIPSEWD - MINIECLIPSETRWD

3.5 STATIC MODE

This xture has the ability to accept custom static color settings. Access this via the control panel.

• To enable the static mode, press MENU repeatedly until STATIC shows on the display.

• Through the button UP/DOWN select DIMMER or STROBE then press the button ENTER.

• Set the value (000 - 255), through the buttons UP/DOWN.

• Press the button ENTER to conrm.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.6 DMX CONFIGURATION

MINIECLIPSEWD/TRWD is equipped with dierent DMX conguration.

• Press the button MENU so many times until shows DMX CHANNEL, and press the button ENTER to conrm.

• Select the desired DMX conguration (1CH - 2CH - 5CH ) through the buttons UP/DOWN.

The tables on page 13 indicate the operating mode and DMX value.

3.7 DMX MODE

• Press the button MENU so many times until the display shows DMX ADDRESS, and press the button ENTER

to conrm.

• Press UP/DOWN button to select the desired value (001-512). Press and hold to scroll quickly.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

To able to operate the MINIECLIPSEWD/TRWD with a light controller, adjust the DMX start address for the

rst a DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst

DMX channel, adjust the start address 33 on the MINIECLIPSEWD/TRWD. The other functions of the light

eect panel are then automatically assigned to the following addresses.

An example with the start address 33 is shown below:

Number of

DMX

channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

5 33 33-37 38 43 48

Fig.6 - Esempio di congurazione a 7 canali DMX

DMX512 Controller

wireless

solution

MINIECLIPSEWD - MINIECLIPSETRWD

2 CHANNELS

MODE

FUNCTION DMX

Value

2 Ch

DIMMER

0~100% 000 - 255

STROBE

NO Function

Strobe slow to fast

000 - 010

011 - 255

1 CHANNEL

MODE

FUNCTION DMX

Value

1 Ch

DIMMER

0~100% 000 - 255

3.8 CHANNELS DMX

5 CHANNELS

MODE

FUNCTION DMX

Value

5 Ch

DIMMER

0~100% 000 - 255

STROBE

NO Function

Strobe slow to fast

000 - 010

011 - 255

AUTO PROGRAMS

NO Function

Auto Program 1

Auto Program 2

Auto Program 3

Auto Program 4

000 - 010

011 - 070

071 - 130

131 - 190

191 - 255

AUTO SPEED

0~100% 000 - 255

AUTO PROGRAMS

Present Dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode 1 (fast speed)

Dimmer speed mode 2 (middle speed)

Dimmer speed mode 3 (slow speed)

000 - 010

011 - 070

071 - 130

131 - 190

191 - 255

MINIECLIPSEWD - MINIECLIPSETRWD

3.9 FIXTURE SETTINGS

It is possible to change the parameter value in the following way:

Dimmer

• Enter in Dimmer mode to select specic dimming curve, press the button MENU so many times

until shows DIM MODE, and press the button ENTER to conrm.

• Press the button UP/DOWN to select OFF - DIM1 - DIM2 - DIM3.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

Back Light

• To activate Backlight display press the button MENU so many times until shows BACK LIGHT, and press

the button ENTER to conrm.

• Press the button UP/DOWN to select ON - 10S - 20S - 30S.

• Press ENTER button to conrm the selection.

• Press the MENU button to go back or to meet the waiting time to exit from the setup menu auto-

matically.

3.10 FIXTURE INFORMATION

Fixture Hours

Show the xture working hours.

• Press the button MENU so many times until shows INFORMATION. Press the button ENTER to conrm

• Using the button UP/DOWN to select FIX HOURS, then press the button ENTER to conrm

• Then the display will show the working hours.

• Press the MENU button to go back or to meet the waiting time to exit from the setup menu auto-

matically

Version

Show the xture rmware version.

• Press the button MENU so many times until shows INFORMATION

• Select through the button UP/DOWN the VERSION menu voice.

• The display will show the rmware data.

• Press the MENU button to go back or to meet the waiting time to exit from the setup menu automatically.

3.11 WIRELESS SETTING

To set the wireless mode refer to the following guide:

• Press the MENU button until the display shows Wireless Setting, then press the ENTER button.

• Use the UP/DOWN button until the display reads Wireless Receive, and then press the ENTER button

and select the ON mode.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

NOTE - After you complete these steps, you have to synchronize with any wi unit with which you

want to communicate by pressing the sync button present on the same. Then connect any DMX

console to wi unit for to open the communication with the MINIECLIPSEWD/TRWD unit.

• To reset the unit press the MENU button until the display shows Wireless Reset, then press the ENTER

button.

• Use the UP/DOWN button until the display reads Yes, and then press the ENTER button.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

MINIECLIPSEWD - MINIECLIPSETRWD

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch o the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

4.2 TROUBLESHOOTING

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• Faulty LED

• Check the power supply voltage

• Increase the value of the dimmer channels

• Replace the LED board

General low light intensity

• Dirty lens assembly

• Misaligned lens assembly

• Clean the xture regularly

• Install lens assembly properly

Fixture does not power up

• No power

• Loose or damaged power cord

• Check for power on power outlet

• Check power cord

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

REV.001-11/15

Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.

La riproduzione - anche parziale - per propri scopi commerciali è vietata.

Al ne di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modicare, in

qualunque momento e senza preavviso, le speciche menzionate nel presente manuale di istruzioni.

Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it

MINIECLIPSEWD - MINIECLIPSETRWD

• MINIECLIPSEWD/MINIECLIPSETRWD

• Manuale utente

Contenuto dell'imballo:

INDICE

Sicurezza

Avvertenze generali

Attenzioni e precauzioni per l’installazione

1 Introduzione

1. 1 MINIECLIPSEWD Descrizione

1. 2 Speciche tecniche

1. 3 MINIECLIPSETRWD Descrizione

1. 4 Speciche tecniche

1. 5 Congurazione MINIECLIPSEWD/TRWD

1. 6 Elementi di comando e di collegamento

2 Installazione

2. 1 Montaggio

3 Funzioni e impostazioni

3. 1 Funzionamento

3. 2 Impostazione base

3. 3 Struttura menù

3. 4 Modalità Autoshow

3. 5 Modalità Static

3. 6 Congurazione canali

3. 7 Modalità DMX

3. 8 Canali DMX

3. 9 Funzioni dispositivo

3. 10 Informazioni sul dispositivo

3. 11Impostazioni Wireless

4 Manutenzione

4. 1 Manutenzione e pulizia del sistema ottico

4. 2 Risoluzione dei problemi

MINIECLIPSEWD - MINIECLIPSETRWD

ATTENZIONE! Prima di effettuare qualsiasi operazione con l’unità, leggere con attenzione

questo manuale e conservarlo accuratamente per riferimenti futuri. Contiene informazioni

importanti riguardo l’installazione, l’uso e la manutenzione dell’unità.

SICUREZZA

Avvertenze generali

• I prodotti a cui questo manuale si riferisce sono conformi alle Direttive della Comunità Europea e per-

tanto recano la sigla .

• Il dispositivo funziona con pericolosa tensione di rete 230V~. Non intervenire mai al suo interno al di

fuori delle operazioni descritte nel presente manuale; esiste il pericolo di una scarica elettrica.

• È obbligatorio eettuare il collegamento ad un impianto di alimentazione dotato di un’eciente messa

a terra (apparecchio di Classe I secondo norma EN 60598-1). Si raccomanda, inoltre, di proteggere le

linee di alimentazione delle unità dai contatti indiretti e/o cortocircuiti verso massa tramite l’uso di

interruttori dierenziali opportunamente dimensionati.

• Le operazioni di collegamento alla rete di distribuzione dell’energia elettrica devono essere eettuate

da un installatore elettrico qualicato. Vericare che frequenza e tensione della rete corrispondono alla

frequenza ed alla tensione per cui l’unità è predisposta, indicate sulla targhetta dei dati elettrici.

• L’unità non per uso domestico, solo per uso professionale.

• Evitare di utilizzare l’unità:

- in luoghi soggetti a vibrazioni, o a possibili urti;

- in luoghi a temperatura superiore ai 45°C.

• Evitare che nell’unità penetrino liquidi inammabili, acqua o oggetti metallici.

• Non smontare e non apportare modiche all’unità.

• Tutti gli interventi devono essere sempre e solo eettuati da personale tecnico qualicato. Rivolgersi al

più vicino centro di assistenza tecnica autorizzato.

• Se si desidera eliminare il dispositivo denitivamente, consegnarlo

per lo smaltimento ad un’istituzione locale per il riciclaggio.

Attenzioni e precauzioni per l’installazione

• Se il dispositivo dovesse trovarsi ad operare in condizioni dierenti da quelle descritte nel presente

manuale, potrebbero vericarsi dei danni; in tal caso la garanzia verrebbe a decadere. Inoltre, ogni altra

operazione potrebbe provocare cortocircuiti, incendi, scosse elettriche, rotture etc.

• Prima di iniziare qualsiasi operazione di manutenzione o pulizia sull’unità togliere la tensione dalla rete

di alimentazione.

• È assolutamente necessario proteggere l’unità per mezzo di una fune di sicurezza. Nell’eseguire qual-

siasi intervento attenersi scrupolosamente a tutte le normative (in materia di sicurezza) vigenti nel

paese di utilizzo.

• Installare l’unità in un luogo ben ventilato.

• Mantenere i materiali inammabili ad una distanza di sicurezza dall’unità.

• I ltri, le lenti o gli schermi ultravioletti se danneggiati possono limitare la loro ecienza.

• I LED devono essere sostituiti se danneggiati o termicamente deformati.

• Non guardare direttamente il fascio luminoso. Tenete presente che i veloci cambi di luce possono pro-

vocare attacchi d’epilessia presso persone fotosensibili o epilettiche.

• Non toccare l’alloggiamento del prodotto quando è in funzione perché potrebbe essere molto caldo.

La pagina si sta caricando...

ProLights 28 W track mounted mini LED profile Manuale utente

Marca: ProLights

Modello: 28 W track mounted mini LED profile

Categoria: Stroboscopi

Tipo: Manuale utente

Scarica PDF

rapporto

in altre lingue

English: ProLights 28 W track mounted mini LED profile User manual

Documenti correlati

Altri documenti

AudioQuest HDMIVOD08 Manuale utente