Viscount D:Sider M12 Manuale del proprietario

Marca: Viscount

Modello: D:Sider M12

Categoria: Altoparlanti

Tipo: Manuale del proprietario

Questo manuale è adatto anche per

D:Sider M15

Important Notes........................................................................................ 2

Overview....................................................................................................3

Controls and Connections..........................................................................6

DSP controls.............................................................................................. 8

Powercon connections............................................................................... 10

Audio Connections.................................................................................... 10

RS-485 connections..................................................................................12

Usage Suggestions.....................................................................................13

Technical Specification.............................................................................. 14

Block Diagram........................................................................................... 15

We live in a universe of sounds.

Sounds to be captured and reproduced, which can just accompany our life, but can also be exalting

and exciting. We were convinced we could reproduce this universe of sound in a new way – which is

why we created Verse. New manufacturing technologies for amplifiers and loudspeakers, combined

with a full digital control from the input socket up to the loudspeaker coil, made us decide to accept

this challenge. In fact, Verse is total sound purity, giving results whose quality is unrivalled in such

small dimensions.

Verse systems are built to astonish for their incredible quality and, thanks to their compactness and

light weight, can always fit in alongside you anywhere. Follow us in our new venture and make it

yours, re-discovering your universe of sounds.

The Verse team

OPEN SYSTEMS FOR OPEN MINDS

THANK YOU FOR CHOOSING A VERSE D:SIDER M SERIES PRODUCT.

THIS GUIDE WILL GIVE YOU INFORMATION AND USEFUL TIPS FOR A CORRECT USE OF YOUR

D:SIDER MONITORS.

THE VERSE STAFF WISHES YOU GOOD WORK AND... HAVE FUN!

LOOKING AFTER THE PRODUCT

• Never apply excessive force to the structures or controls (knobs, switches).

• Do not stress the speaker in transit or during use.

• Do not place the device close to heat sources, in damp or dusty places or

close to strong magnetic fields.

• When possible, do not place the speaker close to units which generate strong

interference, such as radio and TV sets, monitors, etc.

• Never insert objects or liquids of any kind inside the device, for any reason.

• Clean using a soft brush or an air jet only; never use detergents, solvents or

alcohol.

• When disconnecting cables from sockets, always take hold of them by the

connector and not by the cable itself, and when winding take care to avoid

knots or twisting.

• Do not expose the speaker to direct sunlight.

CONNECTING TO THE MAINS

• To avoid the risk of electric shock, do not make connections with wet hands.

• Make sure that the mains voltage is the same as that indicated on the control

panel.

• Connect the speaker to a mains socket with earth contact.

CONNECTING TO A MIXER

• Always use good quality screened cables.

• Before making the connections, check that all the speakers you are about to

connect are switched off. You will avoid noisy, if not hazardous, signal peaks.

IN CASE OF MALFUNCTION

• In case of malfunction, contact only an authorised service centre.

Verse speakers are developed from the idea that speech and music satisfy us

when they are intelligible, undistorted and pleasant to listen to.There’s no such

thing as a system suited to one musical genre or another – these are just

illusions caused by our personal taste. A real sound system can follow you

anywhere: whether you’re in a lounge bar accompanying an aperitif, in a

traditional theatre, or just outdoors with a few instruments or a large orchestra.

In order to do this we applyed the latest design, manufacturing technologies

and DSP processing, and that's what gives Verse systems a huge reserve of

dynamics, which can be heard when the need arises.

The experience of listening to Verse will enable you to discover many new

horizons - a real uniVerse:

• really precise presence for vocals, with a clear image of the other instruments

• natural, dynamic low frequencies that are not pumped up, but give an

unforgettable physical sensation

• crystal-clear high frequencies that are upfront, but never disturb

• a great natural reaction to equalization, to satisfy users’ personal taste,

thanks to the great reserve of dynamics and the capacity of the new

transducers

TECHNOLOGY

DIGITAL AMPLIFIERS

The new digital technology totally changed the way a professional audio amplifier is

developed. No other way make possible to give great power and long term reliability.

Remarkable heat reduction and outstanding weight decrease make digital amplifier,

that equip VERSE D:SIDER MONITORS, efficient, powerful and less heating. The output

stages of the amplifiers typically run at 95% efficiency, dissipating only 5% of the input

energy as heat.

Moreover the efficiency doesn't depend on the output level, and Since standard music

has an average power density of 40% of the maximum level, conventional amplifiers

can easily generate 10 times more heat than VERSE ones for the same volume of

sound.

To grant reliability and durability, VERSE amplifiers are provided with short-circuit

protection, thermal protection with fan-speed control (that avoid temperature rising

over 60° C) and amplifier disactivation system thus preventing amplifier breakdown if

temperature rise to intolerable values.

And also: protection circuit to cancel direct current component, protection from

ultrasonic components in input and output. The I.T.P (Intelligent Thermal Protect) is

warranty of perfect-working and long-lasting speakers.

TOP QUALITY COMPONENTS

Together with high performance amplifiers, VERSE decided to put speakers

conceived specifically to do their best with a so remarkable reserve of power.

The woofer are made with neodymium magnets that allows the highest force factor

and excursion capability, and with ventilated voice coil gap for reduced power

compression. With such components it's easier to obtain huge excursions, "present"

and dynamic bass, high acoustic pressure and mild weights.

The titanium drivers, coaxial type, are custom built for the use in a stage monitor

configuration, with a 40°/60° asimmetric dispersion angle, which proves to be the

best for a stage monitor speaker.

DIGITAL PROCESSING

The processing system included in every D:SIDER M loudspeaker is based on a

performing DSP processor with PC-based remote control using dedicated software.

Sophisticated and innovative processing algorithms have been implemented to

ensure total protection of all system components without sacrificing the dynamic of

the sound source. Digital Limiters switch on when transducers safety conditions or

maximum amplifier power are going to be exceeded, preventing the loudspeakers

from being supplied with higher volume input signals. Along the processing path a

powerful 12 bands feedback remover is placed, detecting any incoming feedback

and immediately suppressing it, without any phase distortion.

The processing unit includes as well a multi-band compressor, a delay line and six

full parametric equalizers.

The digital delay line makes it possible to compensate for vertical alignment

differences between subwoofer and satellites or to create distributed lines of

speakers whose output reaches the listening point simoultaneously, eliminating echo

effects.

The multicomp processor section can be extremely useful for the system's dynamic

EQ and offers a more deep capability to modify and manipulate the dynamic range of

the audio signal.

A six band full parametric EQ may be used to tune the overall audio response to the

need: adapting the frequency response to the ambience, to the musical genre or

speaker voice, to the peculiar use of the moment, to personal tastes, etc.

D:SP EDITOR

To easily customize every parameter of your loudspeakers a PC editor program is

available. This allows to connect to the speakers, editing equalizers and parameters,

but also displaying levels, and checking the status and "health" of every single

loudspeaker connected to this network, showing real time temperature, signal

overloads, limiter activities and other status information of the D:SIDER M.

Two screenshots from the D:SP editor available optionally

8&9

1. POWER: Switches the power on/off.

2. Power AC Out: easily connect another VERSE speaker to the mains. Pay

attention not to exceed the limit reported on the chassis near the grey

connector.

3. Mains In: connect the mains cable supplied from the factory with the

loudspeaker to this socket.

4. Link: sends on output the same signal coming from LINE INPUT connector.

This allow the cascade connection of different devices to the same sound

source.

5. Line input: balanced XLR socket for connection of the signal to be amplified.

6. LEDs:

- ON LED: indicates that the speaker is On.

- Prot. LED: indicates that the internal amplifier switched to protection

mode due to a fault of the amplifier itself or of the connected speakers

(please call the technical support).

- Temp. LED: indicates that the internal amplifier switched to protection

mode due to excessive heating. In this condition, the amplifier supply half

the normal power. Please reduce the input signal to allow the restore of

normal load conditions.

- Comp. H. LED: indicates activity of the High frequency compressor. If the

signal passes over a safety threshold, the compressor guarantees a good

quality playback without acoustic distortion, damping the appropriate signal

frequencies. The system operates in total safety. If the LED is constantly On,

there is an excess of signal. In this case, please reduce the incoming signal

level.

- Comp. L. LED: indicates activity of the Low frequency compressor. If the

signal passes over a safety threshold, the compressor guarantees a good

quality playback without acoustic distortion, damping the appropriate signal

frequencies. The system operates in total safety. If the LED is constantly On,

there is an excess of signal. In this case, please reduce the incoming signal

level.

- Sign. LED: indicates that the signal is present.

7. Gain: to adjust the signal gain in the range from -35dB to 0dB.

8. RS485 OUT : Etherconn connector to connect to the digital network. Use to

connect to the RS485 IN input of the next speaker along the daisy chain.

9. RS485 IN : Etherconn connector to connect to the digital network. Plug here

the cable coming from the RS485 OUT connector of the previous speaker in

the daisy-chain, or the USB-485 interface (D:SP INTERFACE) output if the

speaker is the first in the chain.

SCREW

All the D:SIDER M series speakers are equipped with a powerful DSP (Digital Signal

Processor) which manages the entire signal processing flow. Some of the advanced

functions are ready to use via the simple interface made out of four LED-lighting

switches, accessible when removing the "DSP" panel as shown in the figure. Every

function, described below, can be activated pressing the proper switch. When the LED

is on the DSP function is activated.

The list of LED-switches follows with a description:

- A.Feedb: activates the Automatic Feedback Remover. This consists in an

automatic system constantly monitoring the signal for acoustic feedback

phenomena, steadily suppressing them with 12 adaptive notch filters. The

system detects potential feedback araising, localizes the exact frequency

and activates a very narrow notch filter (with Q factor up to 1/40 octave) on

the given frequency.

- Voice Enh.: activates the Voice Enhancer function. This consists in a specific

compression and loudness configuration, created to give prominence to

the vocal parts. To be used to monitor singers.

- Near Side: activates the Near Side function. This is a specific equalization,

made to use the monitor together with other monitors all close together

forming an array.

- User: activates the "user settings", prepared with the proper software

editor, D:SP EDITOR sold separately. Whenever the previous setting is not

adequate to the peculiar use case, it can be deactivated, switching back to

the factory settings.

AUTOMATIC FEEDBACK REMOVER

Please note the followings:

- The Automatic Feedback Remover can't totally remove any feedback

phenomenon, but can drastically reduce these, permitting to use the system

at higher volumes and in critical conditions (microphones in front of the

speakers, microphones moving along the stage, etc).

- When the Automatic Feedback Remover is active, if at least one of the 12

filters is working on a specific frequency, the LED blinks.

- To remove every active filter, for example when the position of microphones

and speakers is changed, press the A.Feedb. switch for approx. 3 seconds.

The LED will stop blinking, while remaining on, indicating that none of the

filters is placed on a specific frequency.

Note: The "User" preset is not set by factory, which means the speaker

configuration remains the same either the User LED is turned On or Off,

until a user setting is not configured.

MONITOR 1

The Powercon connectors make the system very practical

and, thanks to the LINK OUTPUT on each enclosure, avoid

the problem of having to run a power feed to each element.

Detail of a Powercon

main input

Configuration 1. L+R D:SIDER + 2 D:SIDER M Monitors

MONITOR 2

AUDITORIUM LEFT

AUDITORIUM RIGHT

Audio connections can be arranged in many different ways, depending on the

situation, the number and type of speakers, the ambience dimensions. The

following examples are intended to give an idea on how to route and use the

D:SIDER M speakers.

Configuration 2. Monitor array w/ NearSide function

Configuration 3. Singer Monitor w/ Voice Enhancer

SINGER'S PERSONAL MONITOR

In addition to the DSP functionalities, directly accessible on the speaker, described in

the previous paragraph, it's possible to control in a broader way the speaker of the

D:SIDER M series using an RS485 remote control interface and a personal computer.

An optional USB-485 interface (D:SP INTERFACE) and a personal computer software

(D:SP EDITOR) are available to the purpose. In this way it's possible to control a large

amount of parameters within the signal processing and to monitor in real time

important aspects of the speakers functioning.

With a single USB-485 it is possible to connect in daisy chain up to 127 different

speakers.

For a complete description please refer to the D:SP EDITOR + D:SP INTERFACE user

manual. It is anyway possible to have a preview of the available functionalities,

installing on a personal computer the DEMO version of that software, that can be

found in the attached CD or be downloaded from the official site

www.verseaudio.com

Note: to connect the D:SIDER M speakers to the network use only high quality

Ethernet cables of the CAT5 type.

An example of a daisy chain network for the VERSE D:SIDER M systems is shown in

figure below.

Warning: even if the digital D:SP Verse network is made of common

Ethernet cables, IT IS NOT an Ethernet network, therefore IT IS NOT

possible to connect the D:SIDER M speakers to Ethernet devices. It is,

instead, necessary to make use of the proper VERSE D:SP INTERFACE (USB-

485), available as optional.

The acoustic characteristics of the room/environment in which a sound system is used have

sometimes very significant effects on the overall sound produced.

Thanks to its special technical features (such as the optimal width of its dispersion range),

with the D:SIDER M some of the most common problems can be reduced or prevented.

However, some factors should be borne in mind as they may help to optimise its

performance.

• Do not place speakers in the corners of a room or in recesses (e.g. niches), since this

causes an increase in the low frequencies, producing sounds which are redundant or

blurred.

• Do not place speakers against a wall, as this also causes an increase in the low frequencies,

although less pronounced than that produced in a corner or niche.

N.B.: on the other hand, this phenomenon may sometimes be used to advantage to

reinforce the low range, but it must be employed carefully and in a controlled way.

• Do not place speakers straight on a stage, a floating floor or any other support with

cavities, as this tends to trigger resonances that alter and interfere with the overall sound.

N.B.: solid supports should always be used when possible, or a speaker stand.

• Remember that high frequencies have a high level of directivity and a much higher

absorption coefficient than low frequencies. Therefore, to guarantee that the signal

reaches the listener in an intelligible form, position speakers so that they are in a direct

line with the audience (clearly visible) about ½ metre / 1 metre above the audience’s heads.

• In buildings with a lot of reverberation (places of worship, gymnasiums, etc.) first of all

keep the sound reflections down using materials which absorb sound (carpets, curtains,

special panels, etc.). If this is not possible or is not sufficient, do not simply turn up the

volume, because this will also increase the volume of the reflected sound, and may make

the situation even worse. The best solution is to use more speakers, placed around the

room and closer to the audience (e.g. front+back; front+sides; front+sides+back).

N.B.: in these circumstances it may prove necessary to use the integrated delay line

provided with the D:SIDER M internal DSP processor to realign the timing of the sound of

the various speakers (i.e. to overcome the delays caused by the sound propagation time),

ensuring that the sound heard by the audience will be free from “echo”.

Example: since the speed of sound is about 344 metres a second, sound takes about 1/10

of a second to travel 30 metres. Therefore, a listener close to a “back” speaker 30 metres

from the “front” speaker would hear the sound from the “back” speaker about 1/10 of a

second before the sound from the “front” speaker: in other words, he would hear two

identical sounds 1/10 of a second apart. To ensure that the two sounds strike the ear of

this specific listener at exactly the same time, the sound of the “back” speaker will have to

be delayed by 1/10 of a second using the D:SIDER M delay line.

La pagina sta caricando ...

Viscount D:Sider M12 Manuale del proprietario

Marca: Viscount

Modello: D:Sider M12

Categoria: Altoparlanti

Tipo: Manuale del proprietario

Questo manuale è adatto anche per

D:Sider M15

Scarica il pdf

rapporto

in altre lingue

English: Viscount D:Sider M12 Owner's manual
Deutsch: Viscount D:Sider M12 Bedienungsanleitung

Viscount D:Sider M12 Manuale del proprietario

Questo manuale è adatto anche per

Viscount D:Sider M12 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti