66250070 - V. 1.4 - 26/11/13
Art.4800-4800M - Installation instructions
Art. 4800 - 4800M
1
CODELOCK UNIT MODULES ART.4800
The module features 12 stainless steel buttons (Keys 0 - 9, ENTER and CLEAR), 2 LED’s for progress information during use and pro-
gramming and a mirror nish stainless steel front plate (Standard version). With three integral relays each with common, normally
open and normally closed connections and two inputs to enable the external triggering of relays one and two (For example, push to
exit button). Key presses are signalled both acoustically and visually while each button press has a tactile feel. Entering the correct
code followed by ENTER will activate the relevant relay. Programming is carried out through the same keypad following a simple
programming menu. The module can be combined with other 4000 Series modules in an audio or video intercom system.
MAIN FEATURES
• 3 C, NC, NO relay outputs (24Vac/dc – 5A max);
• 3 Programmable secret codes (one for each relay);
• Each relay can be set to be activated for a specic time (01 to 99 seconds) or to work as latch;
• Two active low inputs to command directly the relay 1 and 2;
• Programming menu guarded by a 4-8 digit programmable engineer’s code;
• Visual and Acoustic signal during operating and programming;
• Keypad illumination LEDs;
GENERAL DIRECTIONS FOR INSTALLATION
• In order to achieve the best results from the schematics described it is necessary to install only original VIDEX equipment, strictly
keeping to the items indicated on each schematic and follow these General Directions for Installation:
• The system must be installed according to national rules in force, in any case the running of cables of any intercom unit must be carried
out separately from the mains;
• All multipair cables should be compliant to CW1308 specication (0.5mm twisted pair telephone cable).
• Cables for speech line and service should have a max resistance of 10 Ohm
• Lock release wires should be doubled up (Lock release wires and power supply wires should have a max resistance of 3 Ohm);
• The cable sizes above can be used for distances up to 50m. On distances above 50m the cable sizes should be increased to keep
the overall resistance of the cable below the RESISTANCES indicated above;
• Double check the connections before power up;
• Power up the system then check all functions.
LOCK RELEASE BACK EMF PROTECTION
A capacitor must be tted across the terminals on AC lock release (Fig.1A) and a diode must be tted across the terminals on a DC
lock release (Fig.1B) to suppress back EMF voltages.
Connect the components to the lock releases as shown in gures.
4000 Series digital codelock module
66250070 - V. 1.4 - 26/11/13
Art.4800-4800M - Installation instructions
Art. 4800 - 4800M
2
BUZZER BACK EMF
When using intercoms with buzzer call (Art.924/926, SMART1/2, 3101/2, 3001/2 and 3021/2) add one 0,1uF capacitor between
terminals 3 and 6 on the telephone
.
BUILTIN RELAYS BACK EMF PROTECTION ART.4800M
The 4800M includes selectable back EMF protection on the relays. The jumpers marked MOV (One jumper for each relay) are used to select
the protection type. When using a fail secure lock with connections C & NO the jumper should be in the NO position. When using a fail
open lock with connections C & NC the jumper should be in the NC position and when using the codelock to trigger a gate controller or
another third party controller the jumper should be removed completely (This disables the protection on the relay).
PROGRAMMING SEE ALSO THE RELEVANT FLOW CHART
• Enter the “ENGINEER’S CODE”: rst time type six times “1” (111111 factory preset) and press “ENTER” (The red LED will illuminate);
• Conrm “ENGINEER’S CODE” (typing again the same) or type the new code (4 to 8 digits) then press “ENTER” (Melody). Pressing
twice the “ENTER” button without changing the “ENGINEER’S CODE”, will exit from the programming;
• Enter the code (4 to 8 digits) to enable “RELAY 1” or re-enter the existing code then press “ENTER” (Melody);
• Enter the “RELAY 1” operation time (2 digits 01 to 99 I.E. 05=5 seconds, 00= remain open time) or re-enter the existing time then press “ENTER” (Melody);
• Enter the code (4 to 8 digits) to enable “RELAY 2” or re-enter the existing code then press “ENTER” (Melody);
• Enter the “RELAY 2” operation time (2 digits 01 to 99 I.E. 05=5 seconds, 00= remain open time) or re-enter the existing time then
press “ENTER” (Melody);
• Enter the code (4 to 8 digits) to enable “RELAY 3” or re-enter the existing code then press “ENTER” (Melody);
• Enter the “RELAY 3” operation time (2 digits 01 to 99 I.E. 05=5 seconds, 00= remain open time) or re-enter the existing time then
press “ENTER” (Melody);
• The system is ready to use (the red LED will be o).
PROGRAMMING NOTES
• After pressing enter following a command, press ENTER a further twice to exit the programming menu.
RETURN SYSTEM TO PRESET ENGINEER’S FACTORY CODE
• Turn o power to code lock;
• Keep “ENTER” button pressed while turning the power back on;
• Release “ENTER” button;
• The engineer’s code is now set to “111111” (six times one).
OPERATION
• Type in the programmed code and press “ENTER”;
• If the code is correct, the green LED will illuminate for approx. 2 seconds and the relay relevant to the code will operate for the programmed time;
• If a wrong code is entered, a continuous melody will sound for 4 or more seconds, according to the number of mistakes;
• To switch o any relay while operating, type in the relevant code then press the “CLEAR” button;
OPERATION NOTES
• To operate relays together, set the same code for each relay;
• If a wrong code is entered, the system will lock out for 5 seconds which will increase each time a wrong code is entered. The sys-
tem will operate only when the correct code is entered.
TERMINALS
SW2 Relay 2 command signal (active low)
SW1 Relay 1 command signal (active low)
NC3 Relay 3 normally closed contact
NO3 Relay 3 normally open contact
C3 Relay 3 common contact
NC2 Relay 2 normally closed contact
NO2 Relay 2 normally open contact
C2 Relay 2 common contact
NC1 Relay 1 normally closed contact
NO1 Relay 1 normally open contact
C1 Relay 1 common contact
-
12/24Vac/dc power input
+
4000 Series digital codelock module
66250070 - V. 1.4 - 26/11/13
Art.4800-4800M - Installation instructions
Art. 4800 - 4800M
COSTUMER SUPPORT - SUPPORTO CLIENTI
SUPPORTO CLIENTI
COSTUMER SUPPORT
All Countries:
VIDEX ELECTRONICS S.P.A.
www.videx.it - [email protected]
Tel: +39 0734-631669
Fax: +39 0734-632475
All Countries:
VIDEX ELECTRONICS S.P.A.
www.videx.it - [email protected]
Tel: +39 0734-631669
Fax: +39 0734-632475
UK Customers:
VIDEX SECURITY LTD
www.videx-security.com
Tech Line: 0191 224 3174
Fax: 0191 224 1559
UK Customers:
VIDEX SECURITY LTD
www.videx-security.com
Tech Line: 0191 224 3174
Fax: 0191 224 1559
Tutte le nazioni:
VIDEX ELECTRONICS S.P.A.
www.videx.it - [email protected]
Tel: +39 0734-631669
Fax: +39 0734-632475
Il prodotto è marchiato CE a dimostrazione della sua conformità e può essere
distribuito liberamente all’interno dei paesi membri dell’unione europea EU. Questo
prodotto è conforme alle direttive Europee 2004/108/ECC (EMC); 2006/95/ECC (LVD)
e 93/68/ECC (marcatura CE).
Il prodotto è marchiato CE a dimostrazione della sua conformità e può essere
distribuito liberamente all’interno dei paesi membri dell’unione europea EU. Questo
prodotto è conforme alle direttive Europee 2004/108/ECC (EMC); 2006/95/ECC (LVD)
e 93/68/ECC (marcatura CE).
Il prodotto è marchiato CE a dimostrazione della sua conformità e può essere
distribuito liberamente all’interno dei paesi membri dell’unione europea EU. Questo
prodotto è conforme alle direttive Europee 2004/108/ECC (EMC); 2006/95/ECC (LVD)
e 93/68/ECC (marcatura CE).
The product is CE marked demonstrating its conformity and is for distribution within
all member states of the EU with no restrictions. This product follows the provisions
of the European Directives 2004/108/ECC (EMC); 2006/95/ECC (LVD) and 93/68/ECC
(CE marking).
The product is CE marked demonstrating its conformity and is for distribution within all
member states of the EU with no restrictions. This product follows the provisions of the
European Directives 2004/108/ECC (EMC); 2006/95/ECC (LVD) and 93/68/ECC (CE marking).
SUPPORTO CLIENTI
MASTER S.R.L. DIVISIONE ELETTRICA
Via Mario Tognato, 16
35042 Este (Padova) - ITALIA
Tel. +39 0429 602777
Fax +39 0429 601247
Email citofonia@master-de.it
3
4000 Series digital codelock module
TECHNICAL SPECIFICATION
Power Supply: 12/24 Vac/dc – 2VA
Power Consumption: 50mA max
Working Temperature: -10 +50° C
FLOW CHART
ENTER
“ENGINEER’S CODE”
CONFIRM OR CHANGE
“ENGINEER’S CODE”
ENTER
“ACCESS 1 CODE”
ENTER
“ACCESS 1 TIME”
ENTER
“ACCESS 2 CODE”
ENTER
“ACCESS 2 TIME”
ENTER
“ACCESS 3 CODE”
ENTER
“ACCESS 3 TIME”
SYSTEM READY TO USE
FIRST TIME SIX TIMES 1
“111111” FACTORY
PRESET
TYPE AGAIN SIX TIMES “1”
OR THE NEW ENGINEER’S
CODE 4 TO 8 DIGITS
TWO DIGITS (01 TO 99)
I.E. 05=5 SECONDS
00= REMAIN OPEN
CODE TO ENABLE
RELAY 1
4 TO 8 DIGITS
CODE TO ENABLE
RELAY 2
4 TO 8 DIGITS
CODE TO ENABLE
RELAY 3
4 TO 8 DIGITS
TWO DIGITS (01 TO 99)
TWO DIGITS (01 TO 99)
RED LED WILL BE OFF
Press Enter
(Red LED will be ON)
Press Enter
(Melody)
Press Enter
(Melody)
Press Enter
(Melody)
Press Enter
(Melody)
Press Enter
(Melody)
Press Enter
(Melody)
Press Enter
(Melody)
66250070 - V. 1.4 - 05/11/13
Art.4800-4800M - Installation instructions
Art. 4800 - 4800M
4
4000 Series digital codelock module
66250070 - V. 1.4 - 05/11/13
Art.4800-4800M - Installation instructions
Art. 4800 - 4800M
5
4000 Series digital codelock module
66250070 - V. 1.4 - 05/11/13
Art.4800-4800M - Installation instructions
Art. 4800 - 4800M
6
4000 Series digital codelock module
66250070 - V. 1.4 - 05/11/13
Art.4800-4800M - Installation instructions
Art. 4800 - 4800M
7
4000 Series digital codelock module
Note
66250070 - V. 1.4 - 22/11/13
Art.4800-4800M - Installation instructions
Art. 4800 - 4800M
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Videx 4800 Instructions Manual
- Tipo
- Instructions Manual
- Questo manuale è adatto anche per
in altre lingue
- English: Videx 4800