Thermador KBUIT4270A Manuale utente

Marca: Thermador

Modello: KBUIT4270A

Categoria: Frigoriferi

Tipo: Manuale utente

USE & CARE GUIDE

For Built-in Refrigerators

MANUAL DE USO Y

CUIDADO

Para los refrigeradores

empotrados

GUIDE

D’UTILISATION ET

D’ENTRETIEN

Pour réfrigérateurs encastrés

Side by Side Model/

Modelo de dos puertas/

Modèle côte à côte

KBUIT4250A, KBUDT4250A

KBUIT4260A, KBUDT4260A

KBUIT4270A, KBUDT4270A

KBUIT4850A, KBUDT4850A

KBUIT4860A, KBUDT4860A

KBUIT4870A, KBUDT4870A

For questions about features, operation/performance,

parts accessories or service, call: 1-800-735-4328

In Canada, call for assistance 1-800-735-4328, for

installation and service, call: 1-800-735-4328 or visit

our website at... www.thermador.com

Para consultas respecto a características, operación/

desempeño, partes, accesorios o servicio, llame al:

1-800-735-4328

En Canadá, para obtener asistencia llame al

1-800-735-4328, para instalación y servicio llame al:

1-800-735-4328 o visite nuestra página de Internet...

www.thermador.com

Au Canada, pour assistance, composez le

1-800-735-4328, pour installation ou service le

1-800-735-4328 ou visitez notre site web à...

www.thermador.com

2302752

TABLE OF CONTENTS

REFRIGERATOR SAFETY .............................................................3

Proper Disposal of Your Old Refrigerator....................................3

BEFORE USE..................................................................................4

REFRIGERATOR USE....................................................................4

Power On/Off Switch ...................................................................4

Water System Preparation...........................................................5

Normal Sounds ............................................................................5

Ensuring Proper Air Circulation....................................................6

Using the Controls .......................................................................6

REFRIGERATOR FEATURES ........................................................7

Water and Ice Dispensers............................................................7

Water Filtration System................................................................8

Refrigerator Shelves.....................................................................9

Deli Pan ........................................................................................9

Deli Pan Temperature Control ...................................................10

Crisper Drawers and Covers......................................................10

Covered Utility Bin .....................................................................10

Wine Rack ..................................................................................11

FREEZER FEATURES..................................................................11

Ice Maker and Storage Bin ........................................................11

Freezer Shelf ..............................................................................12

Freezer Basket ...........................................................................12

DOOR FEATURES........................................................................12

Utility Compartment...................................................................12

Door Bins....................................................................................13

REFRIGERATOR CARE ...............................................................13

Cleaning......................................................................................13

Changing the Light Bulbs...........................................................14

Power Interruptions....................................................................14

Vacation and Moving Care.........................................................14

TROUBLESHOOTING ..................................................................15

ASSISTANCE OR SERVICE.........................................................18

In the U.S.A. ...............................................................................18

In Canada...................................................................................18

Replacement Parts.....................................................................18

WATER FILTER CERTIFICATIONS.............................................18

PRODUCT DATA SHEETS...........................................................19

WARRANTY ..................................................................................20

ÍNDICE

SEGURIDAD DEL REFRIGERADOR...........................................21

Cómo deshacerse adecuadamente de su refrigerador viejo....21

ANTES DE USAR..........................................................................22

USO DE SU REFRIGERADOR.....................................................22

Interruptor de Encendido/Apagado...........................................22

Preparación del sistema de agua..............................................23

Sonidos normales ......................................................................23

Cómo asegurar la debida circulación del aire...........................24

Uso de los controles ..................................................................24

CARACTERÍSTICAS DEL REFRIGERADOR..............................25

Despachadores de agua y hielo ................................................25

Sistema de filtración de agua ....................................................26

Estantes del refrigerador............................................................27

Compartimiento para carnes frías .............................................28

Control de temperatura del compartimiento para carnes frías.28

Cajones para verduras y tapas..................................................29

Compartimiento de uso general con tapa.................................29

Portabotellas ..............................................................................29

CARACTERÍSTICAS DEL CONGELADOR .................................29

Fábrica de hielo y depósito de almacenamiento.......................29

Estante del congelador ..............................................................31

Canastilla del congelador...........................................................31

CARACTERÍSTICAS DE LA PUERTA .........................................31

Compartimiento utilitario............................................................31

Recipientes de la puerta ............................................................31

CUIDADO DE SU REFRIGERADOR............................................32

Limpieza .....................................................................................32

Cómo cambiar los focos............................................................33

Cortes de corriente.....................................................................33

Cuidado durante las vacaciones y mudanzas...........................33

SOLUCIÓN DE PROBLEMAS......................................................34

AYUDA O SERVICIO TÉCNICO...................................................38

En los EE.UU..............................................................................38

En Canadá..................................................................................38

Piezas de repuesto.....................................................................38

HOJA DE DATOS DEL PRODUCTO ...........................................39

GARANTÍA.....................................................................................40

TABLE DES MATIÈRES

SÉCURITÉ DU RÉFRIGÉRATEUR ..............................................41

Mise au rebut de votre vieux réfrigérateur.................................41

AVANT L’UTILISATION ................................................................42

UTILISATION DU RÉFRIGÉRATEUR..........................................42

Commutateur marche/arrêt........................................................42

Préparation du système d’eau...................................................43

Sons normaux............................................................................43

Pour s’assurer d’une circulation d’air appropriée......................44

Utilisation des commandes........................................................44

CARACTÉRISTIQUES DU RÉFRIGÉRATEUR ...........................45

Distributeurs d’eau et de glaçons..............................................45

Système de filtration d'eau ........................................................46

Tablettes du réfrigérateur...........................................................47

Tiroir de spécialités alimentaires................................................48

Commande de température du tiroir

de spécialités alimentaires.........................................................48

Bac à légumes et couvercles.....................................................49

Casier utilitaire couvert...............................................................49

Casier à vin.................................................................................49

CARACTÉRISTIQUES DU CONGÉLATEUR...............................49

Machine à glaçons et bac d’entreposage .................................49

Tablette de congélateur .............................................................51

Panier du congélateur................................................................51

CARACTÉRISTIQUES DE LA PORTE.........................................51

Compartiment utilitaire...............................................................51

Compartiments dans la porte ....................................................51

ENTRETIEN DU RÉFRIGÉRATEUR ............................................52

Nettoyage...................................................................................52

Remplacement des ampoules d’éclairage ................................52

Pannes de courant.....................................................................53

Entretien avant les vacances ou lors d’un déménagement.......53

DÉPANNAGE.................................................................................54

ASSISTANCE OU SERVICE.........................................................57

Pièces de rechange....................................................................57

FEUILLES DE DONNÉES SUR LE PRODUIT.............................58

GARANTIE.....................................................................................59

REFRIGERATOR SAFETY

Proper Disposal of

Your Old Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

– even if they will sit for “just a few days.” If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before you throw away your old refrigerator or freezer:

■

Take off the doors.

■

Leave the shelves in place so that children may not easily

climb inside.

You can be killed or seriously injured if you don't

immediately follow instructions.

You

can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or

“WARNING.” These words mean:

BEFORE USE

Removing packaging materials

■

Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

■

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see the “Refrigerator Safety” section.

Cleaning before use

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in the “Refrigerator Care” section.

REFRIGERATOR USE

Power On/Off Switch

If you need to turn the power to your refrigerator ON or OFF, you

must remove the top grille to gain access to the On/Off switch.

Turn the power to the refrigerator OFF when cleaning or changing

light bulbs.

Remove and replace top grille

Remove top grille:

1. Grasp both ends of the top grille.

2. Push the top grille straight up, then pull straight out. Lay the

top grille on a soft surface.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when re-

moving them to avoid impact from dropping.

1. Top grille

2. Cabinet side trims

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Do not use an extension cord.

Do not use an adapter.

Do not remove ground prong.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion,

or fire.

2 21

Replace top grille:

1. Insert top grille hooks (located on the back of the top grille)

into the slots on the side trim.

2. Pull grille down slightly to lock into place.

Turn Power On or Off:

1. Remove top grille.

2. Press main power switch to the ON or OFF position.

3. Replace top grille.

IMPORTANT: Be sure the power switch is set to the ON position

after cleaning refrigerator or changing light bulbs.

Water System Preparation

Please read before using the water system.

Immediately after installation, follow the steps below to make

sure that the water system is properly cleaned.

1. Open the freezer door and turn off the ice maker. For Style 1

lift up the wire shutoff arm as shown. For Style 2 move the

switch to the OFF (right) setting as shown. The ON/OFF

switch is located on the top right side of the freezer

compartment.

Style 1 – Non-Dispenser Models

Style 2 – Dispenser Models

NOTES:

■

If your model has a base grille filter system, make sure the

base grille filter is properly installed and the cap is in the

horizontal position.

■

■■

■

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

2. Use a sturdy container to depress the water dispenser bar

until the water begins to flow. Flush the water system by

dispensing and discarding 2 to 3 gal. (8 to 12 L) of water.

Cleaning the system will take approximately 6 to 7 minutes

and will help clear air from the line. Additional flushing may be

required in some households.

NOTE: As air is cleared from the system, water may spurt out

of the dispenser.

3. Open the freezer door and turn on the ice maker. For Style 1

lower the wire shutoff arm. For Style 2 move the switch to the

ON (left) position. Please refer to the “Ice Maker and Storage

Bin” section for further instructions on the operation of your

ice maker.

■

Allow 24 hours to produce the first batch of ice.

■

Discard the first three batches of ice produced.

■

Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

Normal Sounds

Your new refrigerator may make sounds that your old one didn’t

make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard

surfaces, such as the floor, walls, and cabinets, can make the

sounds seem louder. The following describes the kinds of sounds

and what may be making them.

■

If your product is equipped with an ice maker, you will hear a

buzzing sound when the water valve opens to fill the ice

maker for each cycle.

■

Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperatures and to minimize

energy usage. The high efficiency compressor and fans may

cause your refrigerator to run longer than your old one. You

may also hear a pulsating or high-pitched sound from the

compressor or fans adjusting to optimize performance.

■

You may hear the evaporator fan motor circulating air through

the refrigerator and freezer compartments. The fan speed

may increase as you open the doors or add warm food.

■

Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

■

Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.

■ As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your refrigerator.

■

Contraction and expansion of the inside walls may cause a

popping noise.

■

You may hear air being forced over the condenser by the

condenser fan.

■

You may hear water running into the drain pan during the

defrost cycle.

1. Power On/Off switch

Ensuring Proper Air

Circulation

In order to ensure proper temperatures, you need to permit

airflow between the two sections. Cold air enters the bottom of

the freezer section and moves up. It then enters the refrigerator

section through the top vent. Air then returns to the freezer as

shown.

Do not block any of these vents with food such as soda, cereal,

bread, etc. If the vents are blocked, airflow will be prevented and

the temperature controls will not function properly.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent

odor transfer from food, wrap or cover foods tightly.

Using the Controls

IMPORTANT:

■

The refrigerator control adjusts the refrigerator compartment

temperature. The freezer control adjusts the freezer

compartment temperature.

■

Wait 24 hours after you turn on the refrigerator before you put

food into it. If you add food before the refrigerator has cooled

completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer controls to a

lower (colder) setting will not cool the compartments any

faster.

■

If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

■

The preset settings should be correct for normal household

usage. The controls are set correctly when milk or juice is as

cold as you like and when ice cream is firm.

NOTE: The factory recommended set points are 0°F (-18°C) for

the freezer and 37°F (3°C) for the refrigerator.

Turning Refrigerator On and Viewing Set Points

■

Press and hold POWER (ON/OFF) for 2 seconds.

Viewing the Celsius Temperatures

■

Press °C SELECT touch pad. The negative sign (-) will light

up. To redisplay degrees Fahrenheit, press °C SELECT again.

NOTE: If the freezer temperature is below zero, the negative sign

next to the freezer display will light up. This is normal.

Adjusting Controls

The set point range for the freezer is -5°F to 5°F (-21°C to

-13°C). The set point range for the refrigerator is 34°F to 46°F

(1°C to 8°C).

■

Press the refrigerator or freezer PLUS (+) or MINUS (-) key

pad until the desired temperature is reached.

NOTE: Wait at least 24 hours between adjustments. Recheck

the temperatures before other adjustments are made.

WATER FILTER Status & Reset

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction may

be used on disinfected waters that may contain filterable

cysts.

The water filter display will help you know when it is time to

change your filter. To change the filter, see the “Water Filtration

System” section.

CONDITION/REASON: TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold

Not set correctly for conditions

REFRIGERATOR Control 1°

higher

REFRIGERATOR too warm

High use or room very warm

REFRIGERATOR Control 1°

lower

FREEZER too cold

Not set correctly for conditions

FREEZER Control 1° higher

FREEZER too warm/too little

ice

High use or heavy ice use

FREEZER Control 1° lower

INDICATOR: STATUS:

99 percent New filter installed

10 percent Order replacement filter

0 percent or flow decreases Replace filter

■

After replacing the water filter, press RESET and hold for

2 seconds to change the water filter display to 99 percent.

REFRIGERATOR

FEATURES

Water and Ice Dispensers

(onsomemodels)

You may have one or more of the following options: the ability to

select either crushed or cubed ice, a special light that turns on

when you use the dispenser, or a lock option to avoid accidental

dispensing.

The Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer. When

the dispenser lever is pressed:

■

A trap door opens in a chute between the dispenser and the

ice bin. Ice moves from the bin and falls through the chute.

■

When you release the dispenser lever, the trap door closes

and the ice dispensing stops. The dispensing system will not

operate when the freezer door is open.

To dispense ice:

1. Press button for the desired type of ice.

■

For cubed ice, press the CUBES button.

■

For crushed ice, press the CRUSHED button.

NOTE: For crushed ice, cubes are crushed before being

dispensed. This may cause a slight delay when

dispensing crushed ice. Noise from the ice crusher is

normal, and pieces of ice may vary in size. When

changing from Crushed to Cubes, a few ounces of

crushed ice will be dispensed along with the first cubes.

2. Press a sturdy glass against the ice dispenser lever. Hold the

glass close to the dispenser opening so ice does not fall

outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to

the lever in order to activate the ice dispenser. Pressing hard

will not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing.

NOTE: The first few batches of ice may have an off-flavor

from new plumbing and parts. Throw the ice away. Also, take

large amounts of ice from the ice bin, not through the

dispenser.

The Water Dispenser

If you did not flush the water system when the refrigerator was

first installed, press the water dispenser lever with a glass or jar

until you draw and discard 2 to 3 gal. (8 to 12 L) or approximately

6 to 7 minutes of water after water begins dispensing. It will take

3 to 4 minutes for the water to begin dispensing. The water you

draw and discard cleans the system and helps clear air from the

lines. Allow several hours for the refrigerator to cool down and

chill water.

To dispense water:

1. Press a glass against the water dispenser lever.

2. Remove the glass to stop dispensing.

NOTE: Dispense enough water every week to maintain a fresh

supply.

IMPORTANT: Depending on your model, the small removable

tray at the bottom of the dispenser is designed to catch small

spills and allow for easy cleaning. There is no drain in the tray.

The tray can be removed from the dispenser and carried to the

sink to be emptied or cleaned.

WARNING

Cut Hazard

Use a sturdy glass when dispensing ice or water.

Failure to do so can result in cuts.

The Dispenser Light

The dispenser area has a light. It can be turned on or off manually

by pressing the ON or OFF button.

When you use the dispenser the lever will automatically turn the

light on.

NOTE: See the “Changing the Light Bulbs” section for

information on changing the dispenser light bulb.

The Dispenser Lock

(on some models)

Your dispenser can be turned off for easy cleaning or to prevent

accidental dispensing by small children and pets.

To lock and unlock the dispenser

NOTE: The lock feature does not shut off power to the

refrigerator, to the ice maker, or to the dispenser light. It simply

deactivates the dispenser levers.

1. Press the LOCK button. The ice and water dispensers will not

work.

2. Press the UNLOCK button. Then, continue to dispense ice or

water as usual.

Water Filtration System

The Base Grille Water Filter Status Light

The water filter indicator display will help you know when to

change your water filter cartridge. The display or light is located

at the top of the refrigerator compartment.

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction may

be used on disinfected waters that may contain filterable

cysts.

A new water filter should display a reading of 99% and will

continue to decrease as the filter life is used. When display reads

10%, it is time to order a replacement filter. It is recommended

that you replace the base grille water filter cartridge when the

water filter indicator light changes to 0% OR when water flow to

your water dispenser or ice maker decreases noticeably. (See

“Changing the Base Grille Filter” later in this section.)

After changing the water filter cartridge, reset the water filter

status light by pressing and holding the RESET for 2 seconds.

The indicator light will change to 99% when the filter indicator is

reset.

Changing the Base Grille Filter

1. Locate the water filter cartridge cap in the front base grille.

Rotate the cap counterclockwise to a vertical position and

pull the cap and filter cartridge out through the base grille.

NOTE: There will be water in the cartridge. Some spilling may

occur.

2. Remove the cartridge cap by sliding it off the end of the old

cartridge. The cap will slide to the left or right. DO NOT

DISCARD THE CAP.

3. Take the new cartridge out of its packaging and remove

protective cover from o-rings.

4. Slide the cartridge cap onto the new cartridge. See

illustration in Step 2.

5. With cartridge cap in the vertical position, push the new filter

cartridge into the base grille until it stops. Rotate the cartridge

cap clockwise to a horizontal position. Flush the water

system (see “Flushing the Water System After Replacing

Filter” section).

Flushing the Water System After Replacing Filter

Use a sturdy container to depress the water dispenser bar until

the water begins to flow. Flush the water system by dispensing

and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the

system will take approximately 6 to 7 minutes and will help clear

air from the line. Additional flushing may be required in some

households.

Using the Dispenser Without the Water Filter

You can run the dispenser without a water filter cartridge. Your

water will not be filtered.

1. Remove the base grille water filter cartridge.

2. Slide the cartridge cap off the end of the filter cartridge. DO

NOT DISCARD THE CAP. With the cartridge cap in the

vertical position, insert the cap into the base grille until it

stops.

3. Rotate the cartridge cap to a horizontal position. The

cartridge cap might not be even with the base grille.

Refrigerator Shelves

The shelves in your refrigerator are adjustable to meet your

individual storage needs.

Storing similar food items together in your refrigerator and

adjusting the shelves to fit different heights of items will make

finding the exact item you want easier. It will also reduce the

amount of time the refrigerator door is open, and save energy.

Shelves

1. Remove the shelf by tilting it up at the front and lifting it out of

the shelf supports. Pull shelf straight out.

2. Reposition the shelf supports in the desired location. Check

that they are level and securely in position.

3. Place the back of the shelf in the shelf supports.

4. Lower the front of the shelf and check to make sure that it is

securely in position.

Deli Pan

The deli pan is temperature-controlled.

The temperature in the deli pan can be set to meet the National

Livestock and Meat Board recommended storage temperature

range of 28°F to 32°F (-2°C to 0°C) for fresh meats. See “Deli Pan

Temperature Control.”

The rubber air connector (located in the back of the meat drawer)

directs air from the air supply hole into the meat drawer. If the air

connector comes off, replace it by pushing it into the square

opening on the back of the drawer.

Remove and replace the deli pan cover:

1. Remove the food from the deli pan cover.

2. Pull the pan out about 4 in. (10.16 cm). Reach under the glass

shelf with both hands and lift gently upward until back of shelf

is free.

3. Tilt the shelf at an angle and remove the shelf from the

refrigerator being careful not to bump the glass.

4. Replace the deli pan cover. Hold the deli pan cover firmly with

both hands. Tilt the cover at an angle and position it above

the shelf supports. Place the shelf gently on supports.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when re-

moving them to avoid impact from dropping.

Deli Pan Temperature

Control

The deli pan control adjusts the storage temperature of the deli

pan. Cold air flows into the deli pan through the air duct between

the freezer and the refrigerator. Setting the controls allows more

or less cold air through the air duct. See “Deli Pan.”

Adjust the deli pan temperature:

■

If a colder temperature is needed, turn the control toward

COLDER.

IMPORTANT: If a food item freezes in the deli pan or crisper,

or the water dispenser stops working, turn the deli pan

temperature control to COLD. If the water dispenser stops

working, water in the line may have frozen.

■

If a less cold temperature is needed, turn the control toward

COLD.

■

Turning the control all the way to COLD will shut off the air

duct completely.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish ........................ use same day as purchased

Chicken, ground beef, variety meat (liver, etc.)................ 1-2 days

Cold cuts, steaks/roasts.................................................. 3-5 days

Cured meats .................................................................. 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

Crisper Drawers and Covers

Remove and replace the crisper drawers:

1. Slide the crisper drawer straight out to the stop. Lift the front

of the drawer with one hand while supporting the bottom of

the drawer with your other hand and slide the drawer out the

rest of the way.

2. To replace the crisper drawer, place the drawer onto slides.

Be sure the small bracket on the side of the crisper drawer is

behind the pin on the slide.

3. Push the drawer back and then pull it forward to be sure it is

securely in position.

Clean the crisper covers:

1. To clean the top crisper cover, remove deli pan.

2. To clean the bottom crisper cover, first remove the top crisper

drawer.

Covered Utility Bin

NOTE: For long-term storage, store eggs in a covered container

or in their original carton on an interior shelf.

1. Bracket

2. Pin

Wine Rack

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the

wall of the refrigerator.

FREEZER FEATURES

Ice Maker and Storage Bin

(onsomemodels-Accessory)

Style 1: Non-Dispenser Models

Turn the ice maker on/off:

The on/off switch for the ice maker is a wire shutoff arm located

on the side of the ice maker.

1. To turn the ice maker on, lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice

cubes will raise the wire shutoff arm to the OFF (arm up)

position.

2. To manually turn the ice maker off, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click to make sure

the ice maker will not continue to operate.

Increase ice production rate:

In normal ice production, the ice maker should produce

approximately 7 to 9 batches of ice in a 24-hour period. If ice is

not being made fast enough, turn the Freezer Control toward a

higher (colder) number. Wait 24 hours between each increase.

Remove and replace the ice bin:

1. Flip up the covering panel.

1. Ice maker cover

2. Lift the wire shutoff arm so it clicks into the OFF (up)

position. Ice can still be dispensed, but no more can be

made.

3. Lift up the front of the storage bin and pull the ice bin forward.

4. Replace the bin by pushing it in all the way or the dispenser

will not work. Push the wire shutoff arm down to the ON

position to restart ice production. Make sure the door is

closed tightly.

Style 2: Dispenser Models

Turn the ice maker on/off:

The On/Off switch is located on the top right side of the freezer

compartment.

1. To turn the ice maker on, slide the control to the ON (left)

position.

NOTE: Your ice maker has an automatic shutoff. The ice

maker sensors will automatically stop ice production, but the

control will remain in the ON (left) position.

2. To manually turn the ice maker off, slide the control to the

OFF (right) position.

Remove and replace the ice storage bin:

1. Hold the base of the storage bin with both hands and press

the release button to lift the storage bin up and out.

NOTE: It is not necessary to turn the ice maker control to the

Off (right) position when removing the storage bin. The sensor

cover (“flipper door”) on the left wall of the freezer stops the

ice maker from producing ice if the door is open or the

storage bin is removed.

2. Replace the storage bin on the door and push down to make

sure it is securely in place.

Clean the ice storage bin

1. Empty the ice container. Use warm water to melt the ice if

necessary.

NOTE: Never use anything sharp to break up the ice in the

bin. This can cause damage to the ice container and the

dispenser mechanism.

2. Wash ice bin with a mild detergent, rinse well and dry

thoroughly. Do not use harsh or abrasive cleaners or solvents.

REMEMBER

■

Allow 24 hours to produce the first batch of ice. Allow 3 days

to completely fill ice container.

■

Discard the first three batches of ice produced to avoid

impurities that may be flushed out of the system.

■

The quality of your ice will be only as good as the quality of

the water supplied to your ice maker.

■

Avoid connecting the ice maker to a softened water supply.

Water softener chemicals (such as salt) can damage parts of

the ice maker and lead to poor quality ice. If a softened water

supply cannot be avoided, make sure the water softener is

operating properly and is well maintained.

■

It is normal for the ice cubes to be attached at the corners.

They will break apart easily.

■

For Style 1 ice maker, do not force the wire shutoff arm up or

down.

■

Do not store anything on top of the ice maker or in the ice

storage bin.

Freezer Shelf

1. Remove the shelf by lifting it up and pulling it straight out.

2. Replace the shelf by putting it over the supports and lowering

it into place.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of food,

the type of packaging or wrap used (should be airtight and

moisture-proof), and the storage temperature. Ice crystals inside

a sealed package are normal. This simply means that moisture in

the food and air inside the package have condensed, creating ice

crystals.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 lbs. of food per cubic foot

[907-1,350 g per L] of freezer space). Leave enough space in the

freezer for air to circulate around packages. Be careful to leave

enough room for the door to close tightly.

For more information on preparing food for freezing, check a

freezer guide or reliable cookbook.

Freezer Basket

The freezer basket can be used to store bags of frozen fruits and

vegetables that may slide off freezer shelves.

Remove and replace the freezer basket:

1. Pull the basket forward out to the stop.

2. Lift the front of the basket and slide it out the rest of the way.

3. Replace the basket by positioning it on the side wall guide

rails. Lift the basket front slightly while pushing it past the

guide rail stops and slide basket in the rest of the way.

DOOR FEATURES

Utility Compartment

(on some models)

The utility compartment can be placed in any position on the

refrigerator door.

Remove and replace the utility bin

1. Remove utility compartment by grasping both ends and lifting

compartment up and out.

2. Replace the bin by sliding it in above the desired support and

pushing it down until it stops.

Door Bins

Large door bins hold gallon containers and the smaller door bins

hold 2-liter bottles. The door bins are adjustable and removable

for easy cleaning and adjusting.

Gallon Door Bin

NOTE: The gallon door bin can only be placed on the lower

support.

1. Insert the attachment brackets into the adjustment slots on

the door.

2. Push down on the bin to secure tabs.

3. If necessary, adjust interior shelves to allow for milk jugs and

tall beverage containers stored in the gallon door bin.

Door Bins

1. Remove the bin by lifting it up and pulling it out.

2. Replace the bin by sliding it in above the desired support and

pushing it down until it stops.

REFRIGERATOR

CARE

Cleaning

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

To clean your refrigerator:

1. Remove the top grille. See “Power On/Off Switch.”

2. Press power switch to OFF.

3. Remove all removable parts from inside, such as shelves,

crispers, etc.

4. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

■

Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning

waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts, interior

and door liners or gaskets. Do not use paper towels,

scouring pads, or other harsh cleaning tools. These can

scratch or damage materials.

■

To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs. to 1 qt.

[26 g to .95 L] of water).

5. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water. Do

not use abrasive or harsh cleaners. Dry thoroughly with a soft

cloth. For additional protection against damage to painted

metal exteriors, apply appliance wax (or auto paste wax) with

a clean, soft cloth. Do not wax plastic parts.

6. Clean the condenser coils located behind the top grille

ventilation panel regularly. Coils may need to be cleaned as

often as every other month. This may help save energy.

■

Use a vacuum cleaner with an extended attachment to

clean the condenser coils when they are dusty or dirty.

7. Clean defrost pan using mild detergent in warm water. Dry

thoroughly.

■

Remove the base grille by removing a screw at each end.

■

Remove the defrost pan by pushing up on the retaining

clip under the refrigerator while sliding the pan forward.

■

Replace the defrost pan by positioning the edge of the

defrost pan approximately 7 in. (17.8 cm) from the left

side of the refrigerator. Lift defrost pan into guides and

push back and place pan inside of retaining clip. Replace

the base grille and base grille screws.

8. Press the power switch to the ON position.

9. Replace the top grille. See “Power On/Off Switch.”

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion,

or fire.

1. Defrost pan

2. Retaining clip

Changing the Light Bulbs

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with one of the same size and shape. The

dispenser light requires a heavy duty 10-watt bulb. All other lights

require a 40-watt maximum appliance bulb. Replacement bulbs

are available from your dealer or appliance store.

1. Remove the top grille. See “Power On/Off Switch.”

2. Press the power switch to OFF.

3. Remove light shield when applicable as shown.

NOTE: To clean a light shield, wash it with warm water and a

liquid detergent. Rinse and dry the shield well.

4. Remove light bulb and replace with one of the same size,

shape and wattage.

5. Replace light shield when applicable as shown.

6. Press the power switch ON.

7. Replace the top grille. See “Power On/Off Switch.”

Dispenser Light (on some models)

Reach through the dispenser area to remove and replace light

bulb.

1. Dispenser Light

Refrigerator Control Panel Light

Reach behind the refrigerator control panel to remove and

replace light bulb.

Freezer and Crisper Lights

■

Remove the light shield by grasping the sides and squeezing

in toward the center. Once the side hooks of shield are free

from the freezer or crisper lining, pull down the shield.

■

Replace the light shield by squeezing the sides toward the

center and inserting the side hooks into the slotted holes.

Once the side hooks are in place, snap the front tab into the

slotted hole.

Power Interruptions

If the power will be out for 24 hours or less, keep the door or

doors closed (depending on your model) to help food stay cold

and frozen.

If the power will be out for more than 24 hours, do one of the

following:

■

Remove all frozen food and store it in a frozen food locker.

■

Place 2 lbs (907 g) of dry ice in the freezer for every cubic foot

(28 L) of freezer space. This will keep the food frozen for 2 to

4 days.

■

If neither a food locker nor dry ice is available, consume or

can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled

one. A freezer full of meat stays cold longer than a freezer full of

baked goods. If you see that food contains ice crystals, it may be

refrozen, although the quality and flavor may be affected. If the

condition of the food is poor, dispose of it.

Vacation and Moving Care

Vacations

If you choose to leave the refrigerator on while you’re

away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

■

Raise wire shutoff arm to OFF (up) position or move the

switch to the OFF (right) setting.

■

Shut off water supply to the ice maker.

3. Empty the ice bin.

If you choose to turn the refrigerator off before you leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

■

Turn off the water supply to the ice maker at least one day

ahead of time.

■

When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

3. Depending on the model, turn the Thermostat Control or

Refrigerator Control to OFF. See the “Using the Control(s)”

section.

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

■

Turn off the water supply to the ice maker at least one day

ahead of time.

■

Disconnect the water line from the back of the

refrigerator.

■

When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Depending on the model, turn the Thermostat Control or

Refrigerator Control to OFF. See the “Using the Control(s)”

section.

5. Unplug refrigerator.

6. Empty water from the defrost pan.

7. Clean, wipe, and dry thoroughly.

8. Take out all removable parts, wrap them well, and tape them

together so they don’t shift and rattle during the move.

9. Depending on the model, raise the front of the refrigerator so

it rolls more easily OR screw in the leveling legs so they don't

scrape the floor. See the “Level Refrigerator” section in the

Installation Instructions.

10. Tape the doors closed and tape the power cord to the

refrigerator cabinet.

When you get to your new home, put everything back and refer to

the Installation Instructions for preparation instructions. Also, if

your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the

cost of an unnecessary service call.

Your refrigerator will not operate

■

Is the power supply cord unplugged? Plug into a grounded

3 prong outlet.

■

Has a household fuse blown or circuit breaker tripped?

Replace the fuse or reset the circuit breaker.

■

Is the refrigerator or freezer control turned to the OFF

position? Refer to the “Using the Control(s)” section.

■

Is the refrigerator defrosting? Recheck to see if the

refrigerator is operating in 30 minutes. Your refrigerator will

regularly run an automatic defrost cycle.

■

Is the refrigerator not cooling? For models with digital

controls, turn the unit OFF then ON again to reset. See the

“Using the Control(s)” section. If this does not correct the

problem, call for service.

The lights do not work

■

Is the power supply cord unplugged? Plug into a grounded

3 prong outlet.

■

Is a light bulb loose in the socket or burned out? See the

“Changing the Light Bulb(s)” section.

There is water in the defrost drain pan

■

Is the refrigerator defrosting? The water will evaporate. It is

normal for water to drip into the defrost pan.

■

Is it more humid than normal? When it is humid, expect that

the water in the defrost pan will take longer to evaporate.

The motor seems to run too much

■

Is the room temperature hotter than normal? The motor

will run longer under warm conditions. At normal room

temperatures, expect your motor to run about 80% of the

time. Under warmer conditions, it will run even more.

■

Has a large amount of food just been added to the

refrigerator? Adding a large amount of food warms the

refrigerator. The motor normally will run longer to cool the

refrigerator back down.

■

Are the doors opened often? The motor will run longer

when this occurs. Conserve energy by getting all items out at

one time, keeping food organized, and closing the door as

soon as possible.

■

Are the controls not set correctly for the surrounding

conditions? Refer to the “Using the Control(s)” section.

■

Are the doors not closed completely? Close the doors

firmly. If they do not close completely, see “The doors will not

close completely” later in this section.

■

Are the condenser coils dirty? This prevents air transfer and

makes the motor work harder. Clean the condenser coils.

Refer to the “Cleaning” section.

■

Are the door gaskets not sealed all the way around?

Contact a technician or other qualified person.

NOTE: Your new refrigerator will run longer than your old one

due to its high-efficiency motor.

The refrigerator seems to make too much noise

■

The sounds may be normal for your refrigerator. See the

“Normal Sounds” section.

The ice maker is not producing ice or not enough ice

■

Has the ice maker just been installed? The ice bin holds

14 to 17 lbs. (6.4 to 7.7 kg) of ice. The ice bin can take three

to four days to completely fill, if no ice is used during this

time.

■

Is the freezer temperature cold enough to produce ice?

Wait 24 hours after ice maker hookup for ice production. See

the “Using the Control(s)” section.

■

Is the ice maker wire shutoff arm in the OFF (arm up)

position (on some models)? Lower the wire shutoff arm to

the ON (arm down) position. See the “Ice Maker and Storage

Bin” section.

■

Is the ice maker switch in the OFF (right) position (on

some models)? Move ice maker switch to the ON (left)

position. See the “Ice Maker and Storage Bin” section.

■

Is the water line shutoff valve to the refrigerator turned

on? Turn on the water valve. See the “Connect Water Line to

Refrigerator” section in the Installation Instructions.

■

Does the ice maker mold have water in it or has no ice

been produced? Make sure your refrigerator has been

connected to a water supply and the supply shutoff valve is

turned on. See the “Connect Water Line to Refrigerator”

section in the Installation Instructions.

■

Is an ice cube jammed in the ice maker ejector arm?

For models with an interior ice bin, remove the ice from the

ejector arm with a plastic utensil. For models with an ice bin

located on the freezer door, access the ice maker by

depressing the ice sensor door on the upper left side of the

freezer interior. While depressing the sensor door, lift the ice

maker service door and remove the ice from the ejector with

a plastic utensil. See the “Ice Maker and Storage Bin”

section.

■

Has a large amount of ice just been removed? Allow three

to four days for an empty ice bin to completely fill, if no ice is

used during this time.

■

Are the controls set correctly? See the “Using the

Control(s)” section.

■

Is there a water filter installed on the refrigerator? The

filter may be clogged or installed incorrectly. Check the filter

installation instructions to ensure that the filter was installed

correctly and is not clogged. If installation or clogging is not a

problem, call a technician or other qualified person.

NOTE: If not due to any of the above, there may be a problem

with the water line. Call for service.

Off-taste, odor or gray color in the ice

■

Are the plumbing connections new, causing discolored or

off-flavored ice? Discard the first few batches of ice.

■

Have the ice cubes been stored too long? Throw old ice

away and make a new supply.

■

Does the freezer and ice bin need to be cleaned? See the

“Cleaning” or “Ice Maker and Storage Bin” section.

■

Has food in the freezer or refrigerator been wrapped

properly? Use airtight, moisture-proof packaging to help

prevent odor transfer to stored food.

■

Does the water contain minerals (such as sulfur)? A filter

may need to be installed to remove the minerals.

■

Is there a water filter installed on the refrigerator? Gray or

dark discoloration in ice indicates that the water filtration

system needs additional flushing. Run additional water

through the water dispenser to flush the water filtration

system more thoroughly (at least 2 to 3 gal. [8 to 12 L] or 6 to

7 minutes initially). Discard discolored ice.

The ice dispenser will not operate properly

■

Is the freezer door closed completely? Push the door firmly

shut. If it will not shut all the way, see “The doors will not

close completely” later in this section.

■

Is the ice bin installed correctly? For models with an interior

ice bin, push the ice bin in all the way. If the ice bin does not

go in all the way, it may not be put in straight. Pull it out and

try again. For models with an ice bin located on the freezer

door, the bin should sit level. To remove the bin, press the

release button on the right side of the bin and lift straight up.

Replace the bin in the door making sure it is properly aligned

and snapped securely into place. Refer to the “Ice Maker and

Storage Bin” section.

■

Has the wrong ice been added to the bin? Use only cubes

produced by the current ice maker. If other cubes have been

added, remove all cubes and check to see that none have

become stuck in the delivery chute.

■

Has the ice frozen in the ice bin? Shake the ice bin to

separate cubes. If cubes do not separate, empty bin and wait

24 hours for ice to restock.

■

Has the ice melted around the auger (metal spiral) in the

ice bin? Dump the ice cubes and clean the ice bin

completely. Allow 24 hours for the ice maker to restock. Do

not try to remove the melted ice with a sharp object. You

could damage the ice bin.

■

Is ice stuck in the delivery chute? Clear the ice from the

delivery chute with a plastic utensil. Do not use anything

sharp to remove the ice. You could cause damage.

■

Is the ice dispenser stalling while dispensing “crushed”

ice? Stop dispensing ice. Change the ice button from

“crushed” to “cubed.” Depress the ice dispenser arm using a

sturdy glass. If cubed ice dispenses correctly, depress the

button for “crushed” ice and begin dispensing again. Refer to

the “Water and Ice Dispensers” section.

■

Is there ice in the bin? See “The ice maker is not producing

ice” earlier in this section.

■

Has the dispenser arm been held in too long? Release

dispenser arm. Ice will stop dispensing when the arm is held

in too long. Wait three minutes for dispenser motor to reset

before using again. It is best to take large amounts of ice

directly from the ice bin, not through the dispenser.

Ice bin difficult to remove

■

Is the ice bin difficult to remove (on some models)? For

models with an ice bin located on the freezer door, select

“cubed” ice. Using a sturdy glass, quickly depress and

release the ice dispenser arm. Open the freezer door, depress

the release button on the ice bin and lift upward. Refer to the

“Ice Maker and Storage Bin” section.

The water dispenser will not operate properly

■

Has the water system not filled? The water system needs

to be filled the first time it is used. Use a sturdy container to

depress the water dispenser bar until the water begins to

flow. Flush the water system by dispensing and discarding

2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take

approximately 6 to 7 minutes and will help clear air from the

line. Additional flushing may be required in some households.

See the “Water and Ice Dispensers” section.

■

Is the water shutoff valve not turned on or the water line

connected at the source? Make sure the water shutoff valve

is turned on and the water source is connected to the

refrigerator. See the “Connect Water Line to Refrigerator”

section in the Installation Instructions.

■

Is the water shutoff valve clogged or incorrectly installed?

See the “Connect Water Line to Refrigerator” section in the

Installation Instructions. If clogging or installation is not a

problem, call for service or contact a plumber.

■

Is there a kink in the home water source line? If you find or

suspect a kink in the water line, call for service.

■

Is there a water filter installed on the refrigerator? The

filter may be clogged or incorrectly installed. First, check the

filter installation instructions to ensure that the filter was

installed correctly and is not clogged. If installation or

clogging is not a problem, call for service.

Water or ice is leaking from the dispenser

■

Is the glass not being held under the ice dispenser long

enough, causing the ice to spill? Hold the container under

the ice chute for two to three seconds after releasing the

dispenser lever. Water or ice may continue to dispense during

this time.

■

Is an ice cube stuck in the chute and holding the trap

door open? Remove the cube.

■

Is there a water filter installed on the refrigerator? The

water filtration system may have air in the lines, causing water

to drip. Additional flushing may help clear air from the lines.

Normal dispenser use should flush air from the lines within 24

to 72 hours.

Water flow from the dispenser decreases noticeably

■

Is there a water filter installed on the refrigerator?

The filter may be full or incorrectly installed. Remove the

water filter cartridge (see the “Water Filtration System”

section). Operate the dispenser. If the water flow increases

noticeably, replace the filter.

The dispenser water is not cool enough

■

Has the refrigerator been newly installed? Allow 24 hours

for the refrigerator to cool completely.

■

Has a large amount of water been recently dispensed?

Allow 24 hours for the water to cool completely.

■

Has water not been recently dispensed? The first glass of

water may not be cool. Discard the first glass of water.

The divider between the two compartments is warm

The warmth is probably due to normal operation of the

automatic exterior moisture control. If still concerned, call for

service.

Temperature is too warm

■

Are the air vents blocked in either compartment? This

prevents the movement of cold air from the freezer to the

refrigerator. Remove any objects from in front of the air vents.

See the “Ensuring Proper Air Circulation” section for the

location of air vents.

■

Are the door(s) opened often? The refrigerator will warm

when this occurs. Keep the refrigerator cool by getting all

items out at one time, keeping food organized, and closing

the door as soon as possible.

■

Has a large amount of food just been added to the

refrigerator or freezer? Adding a large amount of food

warms the refrigerator. It can take several hours for the

refrigerator to return to the normal temperature.

■

Are the controls set correctly for the surrounding

conditions? See the “Using the Control(s)” section.

■

Is the refrigerator not cooling? For models with digital

controls, turn the unit OFF then ON again to reset. See the

“Using the Control(s)” section. If this does not correct the

problem, call for service.

There is interior moisture buildup

■

Are the air vents blocked in the refrigerator? Remove any

objects from in front of the air vents. See the “Ensuring

Proper Air Circulation” section for the location of air vents.

■

Are the door(s) opened often? Avoid humidity buildup by

getting all items out at one time, keeping food organized, and

closing the door as soon as possible.

■

Is the room humid? It is normal for moisture to build up

inside the refrigerator when the room air is humid.

■

Is the food packaged correctly? Check that all food is

securely wrapped. Wipe off damp food containers before

placing in the refrigerator.

■

Are the controls set correctly for the surrounding

conditions? See the “Using the Control(s)” section.

■

Was a self-defrost cycle completed? It is normal for

droplets to form after the refrigerator self-defrosts.

The doors will not close completely

■

Are food packages blocking the door open? Rearrange

containers so that they fit more tightly and take up less

space.

■

Is the ice bin out of position? For models with an interior ice

bin, push the ice bin in all the way. If the ice bin does not go in

all the way, it may not be put in straight. Pull it out and try

again. For models with an ice bin located on the freezer door,

the bin should sit level. To remove the bin, press the release

button on the right side of the bin and lift straight up. Replace

the bin in the door making sure it is properly aligned and

snapped securely into place. See the “Ice Maker and Storage

Bin” section.

■

Are the pans, shelves, bins, or baskets out of position?

Put the crisper cover and all pans, shelves, bins, and baskets

back into their correct positions. See the “Crisper Drawers

and Covers” section for more information.

■

Are the gaskets sticking? Clean gaskets according to the

directions in the “Cleaning” section.

■

Does the refrigerator wobble or seem unstable? Level the

refrigerator. See the “Adjust Doors” and “Level Refrigerator”

sections in the Installation Instructions.

The doors are difficult to open

■

Are the gaskets dirty or sticky? Clean gaskets according to

the directions in the “Cleaning” section.

ASSISTANCE

OR SERVICE

Before calling for assistance or service, please check

“Troubleshooting.” It may save you the cost of a service call. If

you still need help, follow the instructions below.

When calling, please know the purchase date and the complete

model and serial number of your appliance. This information will

help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

only use factory specified replacement parts. Factory specified

replacement parts will fit right and work right because they are

made with the same precision used to build every new

THERMADOR

appliance.

To locate factory specified replacement parts in your area, call

1-800-735-4328.

In the U.S.A.

Call the Thermador Customer Interaction Center toll free:

1-800-735-4328.

Our consultants provide assistance with:

■

Features and specifications on our full line of appliances.

■

Referrals to local dealers.

For further assistance

If you need further assistance, you can write to Thermador with

any questions or concerns at:

Thermador

5551 McFadden Ave.

Huntington Beach, CA 92694

Please include a daytime phone number in your correspondence.

In Canada

Call the Thermador Customer Interaction Center toll free:

1-800-735-4328 Monday to Friday 5:00 a.m. - 6:00 p.m. (PST).

Saturday 8:30 a.m. - 4:30 p.m. (PST).

Our consultants provide assistance with:

■

Features and specifications on our full line of appliances.

■

Referrals to local dealers.

For service in Canada

Call 1-800-735-4328. Thermador Canada designated service

technicians are trained to fulfill the product warranty and provide

after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to Thermador

Canada with any questions or concerns at:

Thermador

5551 McFadden Ave.

Huntington Beach, CA 92694

Please include a daytime phone number in your correspondence.

Replacement Parts

To order replacement parts, call 1-800-735-4328 for the

authorized parts distributor in your area. In Canada, call

1-800-735-4328.

Base grille water filter cartridges:

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction may

be used on disinfected waters that may contain filterable

cysts.

Standard Cartridge:

Order Part: WAFILTER (LC400V)

WATER FILTER

CERTIFICATIONS

PRODUCT DATA SHEETS

Base Grille Water Filtration System

Model WF-LC400V/LC400V Capacity 400 Gallons (1514 Liters)

This system has been tested according to ANSI/NSF 42/53 for the reduction of the substances listed below. The concentration of

the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for

water leaving the system, as specified in ANSI/NSF 42/53.

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 63°F

(17.2°C).

■

It is essential that operational, maintenance, and filter

replacement requirements be carried out for the product to

perform as advertised.

■

Model WF-LC400V The filter monitor system measures the

amount of water that passes through the filter and alerts you

to replace the filter. When 90% of the filter’s rated life is used,

the filter indicator light changes from green to yellow. When

100% of the filter’s rated life is used, the filter indicator light

changes from yellow to red, and it is recommended that you

replace the filter. Use replacement cartridge LC400V, part:

WAFILTER. 2003 suggested retail price of $39.99 U.S.A./

$59.95 Canada. Prices are subject to change without notice.

■

The product is for cold water use only.

■

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

■

Refer to the front cover or “Accessories” section for the

Manufacturer’s name, address and telephone number.

■

Refer to the “Warranty” section for the Manufacturer’s limited

warranty.

Application Guidelines/Water Supply Parameters

Substance Reduction

Aesthetic Effects

NSF

Reduction

Requirements

Average

Influent

Influent Challenge

Concentration

Maximum

Effluent

Average

Effluent

Minimum %

Reduction

Average %

Reduction

NSF Test

Number

Chlorine Taste/Odor

Particulate Class 1

≥50%

≥85%

2.1 mg/L

5,366,667/mL

2.0 mg/L ± 10%

At least 10,000

particles/mL

0.06 mg/L

4,100/mL**

0.05 mg/L

2,300/mL

97.1%

99.3%

97.6%

99.9%

507173-02

507175-02

Contaminant

Reduction

NSF

Reduction

Requirements

Average

Influent

Influent Challenge

Concentration

Maximum

Effluent

Average

Effluent

Minimum %

Reduction

Average %

Reduction

NSF Test

Number

Lead: @ pH 6.5

Lead: @ pH 8.5

0.01mg/L

0.16 mg/L***

0.15 mg/L***

0.15 mg/L ± 10%

0.001 mg/L

99.3%

99.2%

99.35%

99.31%

507601-01

507602-01

Mercury: @ pH 6.5

Mercury: @ pH 8.5

0.002 mg/L

0.0061 mg/L

0.0057 mg/L

0.006 mg/L ± 10%

0.0004 mg/L

0.0008 mg/L

0.0003 mg/L

0.00051 mg/L

93.5%

85.8%

96.7%

91.2%

507603-02

507604-02

Benzene 0.005 mg/L 0.0138 mg/L 0.015 ± 10% 0.0005 mg/L 0.005 mg/L 96.3% 96.3% 507183-02

p-dichlorobenzene 0.075 mg/L 0.220 mg/L 0.225 ± 10% 0.0005 mg/L 0.0005 mg/L 99.7% 99.7% 507186-02

Toxaphene 0.003 mg/L 0.014 mg/L 0.015 ± 10% 0.0014 mg/L 0.001 mg/L 90% 92.96% 507185-02

Atrazine 0.003 mg/L 0.009 mg/L 0.009 mg/L ± 10% 0.0013 mg/L 0.00036 mg/L 85.6% 85.6% 507181-02

2, 4-D 0.07 mg/L 0.197 mg/L 0.215 ± 10% 0.058 mg/L 0.0137 mg/L 70.6% 93.06% 507180-02

Asbestos 99% 26 x 10

to 10

fibers/L**** 0.18 x 10

mg/L 0.18 x 10

mg/L 99.93 99.93% 507178-02

Cysts*****

Turbidity

99.95%

0.5 NTU

111,000/mL

11.08 NTU

50,000/L min.

11 ± 1 NTU

1 mg/L

0.13 NTU

1 mg/L

0.078 NTU

99.99%

98.8%

99.99%

99.3%

507187-02

507751-02

Tested and certified by NSF International against ANSI/NSF Standard

42 for the reduction of Chlorine, Taste and Odor, Particulate Class I*;

and against ANSI/NSF Standard 53 for the reduction of Lead,

Mercury, Atrazine, Benzene, Toxaphene, p-dichlorobenzene, 2, 4-D,

Cysts, Turbidity and Asbestos.

Water Supply

Water Pressure

Water Temperature

Service Flow Rate

City or Well

30 - 120 psi (207 - 827 kPa)

33° - 100°F (0.6° - 37.8° C)

0.5 GPM (1.89 L/min.) @ 60 psi.

***

****

*****

Class I particle size: >0.5 to <1 um

Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

These contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.

Fibers greater than 10 um in length

Based on the use of Cryptosporidium parvum oocysts

® NSF is a registered trademark of NSF International.

THERMADOR

BUILT-IN REFRIGERATOR

WARRANTY

TWO-YEAR FULL WARRANTY

For two years from the date of purchase, when this refrigerator (excluding the water filter cartridges) is operated and maintained

according to instructions attached to or furnished with the product, Thermador will pay for factory specified replacement parts and

repair labor costs to correct defects in materials or workmanship. Service must be provided by a Thermador designated service

company.

Water filter cartridge: 30 day limited warranty on water filter. For 30 days from the date of purchase, when this filter is operated and

maintained according to instructions attached to or furnished with the product, Thermador will pay for replacement parts to correct

defects in materials and workmanship.

THIRD THROUGH SIXTH YEAR FULL WARRANTY ON SEALED REFRIGERATION SYSTEM PARTS AS LISTED

In the third through sixth years from the date of purchase, when this refrigerator is operated and maintained according to instructions

attached to or furnished with the product, Thermador will pay for factory specified replacement parts and repair labor costs to correct

defects in materials or workmanship in the sealed refrigeration system. These parts are: compressor, evaporator, condenser, dryer, and

connecting tubing. Service must be performed by a Thermador designated service company.

SEVENTH THROUGH TWELFTH YEAR LIMITED WARRANTY ON SEALED REFRIGERATION SYSTEM

In the seventh through twelfth years from date of purchase, when this refrigerator is operated and maintained according to instructions

attached to or furnished with the product, Thermador will pay for factory specified replacement parts to correct defects in materials or

workmanship in the sealed refrigeration system. These parts are: compressor, evaporator, condenser, dryer, and connecting tubing.

Thermador will not pay for:

1. Service calls to correct the installation of your refrigerator, to instruct you how to use your refrigerator, to replace house fuses or

correct house wiring or plumbing, to replace light bulbs, or to replace water filters other than as noted above.

2. Repairs when your refrigerator is used in other than normal, single-family household use.

3. Pickup and delivery. Your refrigerator is designed to be repaired in the home.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, improper installation, acts of God, or use of products not

approved by Thermador or Thermador Canada.

5. Any food or medicine loss due to product failure.

6. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

7. Removal and replacement of trim or decorative panels that interfere with servicing the product.

8. Labor or parts installed by any non-designated service company during the full warranty period, unless approved by Thermador

before service is performed.

9. In Canada, travel or transportation expenses for customers who reside in remote areas.

10. Any labor costs during the limited warranty periods.

THERMADOR AND THERMADOR CANADA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation

may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or

province to province.

Outside the 50 United States and Canada, a different warranty may apply. Contact your authorized Thermador dealer to

determine if another warranty applies.

If you need service, first see the “Troubleshooting” section of this book. After checking “Troubleshooting,” additional help can be found

by checking the “Assistance or Service” section or by calling the Thermador Customer Interaction Center, 1-800-735-4328 (toll-free),

from anywhere in the U.S.A. In Canada, contact your designated Thermador Canada service company or

call 1-800-735-4328.

5/03

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your refrigerator to

better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the inside wall of the refrigerator

compartment.

Dealer name____________________________________________________

Address ________________________________________________________

Phone number__________________________________________________

Model number __________________________________________________

Serial number __________________________________________________

Purchase date __________________________________________________

La pagina sta caricando ...

Thermador KBUIT4270A Manuale utente

Marca: Thermador

Modello: KBUIT4270A

Categoria: Frigoriferi

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Thermador KBUIT4270A User manual
français: Thermador KBUIT4270A Manuel utilisateur
español: Thermador KBUIT4270A Manual de usuario
português: Thermador KBUIT4270A Manual do usuário

Thermador KBUIT4270A Manuale utente

Thermador KBUIT4270A Manuale utente

in altre lingue

Altri documenti