JVC CD Player GET0172-001A Manuale utente

Categoria
Ricevitori multimediali per auto
Tipo
Manuale utente

Questo manuale è adatto anche per

ENGLISH
‰∑¬
CD RECEIVER KD-S5055
‡§√◊ËÕ߇≈Ëπ
CD KD-S5055
GET0172-001A
[U]
LOUD
SEL
D
IS
P
DIRECT TRACK ACCESS
KD-S5055
CD  !" KD-S5055
For installation and connections, refer to the separate manual.
 !"#$%&'()* !"
°√ÿ≥“¥Ÿ§ŸË¡◊Õ∑’Ë·¬°µË“ßÀ“° „π°“√µ‘¥µ—Èß·≈–°“√‡™◊ËÕ¡µËÕ
INSTRUCTIONS
 !"
§”·π–π”
ENCOVER-KD-S5055[U]f 8/1/03, 10:56 AM1
2
ENGLISH
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid
direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
How to reset your unit
While holding SEL (Select), press (Standby/On Attenuator) for more than 2 seconds.
This will reset the built-in microcomputer.
NOTES:
Your preset adjustments — such as preset channels or sound adjustments — will also be erased.
If a CD is in the unit, it will eject when you reset the unit. Be careful not to drop the CD.
(Standby/On Attenuator)
SEL (Select)
LOUD
SEL
D
I
S
P
EN02-03-KD-S5055[U]f 7/31/03, 1:35 PM2
3
ENGLISH
How to use the MODE button
If you press MODE, the unit goes into functions mode and the number buttons work as different
function buttons.
To use these buttons as number buttons again after pressing MODE, wait for 5 seconds without
pressing any number button until the functions mode is cleared.
• Pressing MODE again also clears the functions mode.
CONTENTS
Thank you for purchasing a JVC product. Please read all instructions carefully before operation,
to ensure your complete understanding and to obtain the best possible performance from the unit.
How to reset your unit .................................. 2
How to use the MODE button ...................... 3
LOCATION OF THE BUTTONS ...............4
Control panel ............................................... 4
BASIC OPERATIONS ..........................5
Turning on the power ................................... 5
RADIO OPERATIONS .........................6
Listening to the radio ................................... 6
Storing stations in memory .......................... 7
Tuning in to a preset station ........................ 8
CD OPERATIONS ..............................9
Playing a CD ................................................ 9
Locating a track or a particular portion
on a CD .................................................. 10
Selecting CD playback modes ................... 10
Prohibiting CD ejection .............................. 11
SOUND ADJUSTMENTS .................... 12
Adjusting the sound ................................... 12
Turning on/off the loudness function ............. 12
Using the Sound Control Memory (SCM) .. 13
Storing your own sound adjustments ........ 14
OTHER MAIN FUNCTIONS ................. 15
Setting the clock ........................................ 15
Canceling Advanced SCM – SCM LINK .... 15
Selecting the level display ......................... 16
Detaching the control panel ....................... 17
MAINTENANCE .............................. 18
Handling discs ........................................... 18
TROUBLESHOOTING ....................... 19
SPECIFICATIONS ............................ 20
BEFORE USE
*
For safety....
Do not raise the volume level too much, as this
will block outside sounds, making driving
dangerous.
Stop the car before performing any complicated
operations.
*
Temperature inside the car....
If you have parked the car for a long time in hot
or cold weather, wait until the temperature in the
car becomes normal before operating the unit.
Time countdown indicator
MODE
MO
RPT RND
7
8
9
10
11
12
EN02-03-KD-S5055[U]f 7/31/03, 1:35 PM3
ENGLISH
4
DIRECT TRACK ACCESS
MO
RPT RND
MODE
SCM
CD
AM
FM
SSM
1
2
3
4
9
8
76
t
w
p
o
;
a
s
d
f g
h
k
j
5
q
e r
i
uy
LOCATION OF THE BUTTONS
1 (Standby/On Attenuator) button
2 +/– buttons
3 LOUD (Loudness) button
4 SEL (Select) button
5 Loading slot
6 AM button
7 0 (Eject) button
8 CD button
9 FM button
p DISP (Display) button
q MO (Monaural) button
w RPT (Repeat) button
e RND (Random) button
r Number buttons
t MODE button
y SCM (Sound Control Memory) button
u
(Control panel release) button
i 4
/ ¢ buttons
Also functions as SSM buttons when
pressed together.
Display window
o SCM (Sound Control Memory) indicator
; CD indicator
a Band indicators
FM1, FM2, FM3
AM
s Tuner reception indicators
MO (Monaural), ST (Stereo)
d RND (Random) indicator
f RPT (Repeat) indicator
g LOUD indicator
h CD-in indicator
j Main display
k Volume level indicator
Control panel
Display window
EN04-04-KD-S5055[U]f 7/31/03, 1:36 PM4
5
ENGLISH
SCM
MO
RPT RND
MODE
SSM
CD
AM
FM
4
Adjust the sound as you want
(see pages 12 – 14).
To drop the volume in a moment
Press briefly while listening to any
source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.
To turn off the power
Press and hold until “SEE YOU”
appears on the display.
Note:
When you use this unit for the first time, set the built-in
clock correctly, see page 15.
Turning on the power
1
Turn on the power.
Note on One-Touch Operation:
When you select a source in step 2 below, the
power automatically comes on. You do not have
to press this button to turn on the power.
2
Select the source.
3
Adjust the volume.
BASIC OPERATIONS
Volume level indicator
(see page 16)
Volume level appears
To increase the volume.
To decrease the volume.
To operate the tuner (FM or AM),
see pages 6 – 8.
To operate the CD,
see pages 9 – 11.
CAUTION on volume setting
CDs produce very little noise compared with other
sources. If the volume level is adjusted for the tuner,
for example, the speakers may be damaged by the
sudden increase in the output level. Therefore, lower
the volume before playing a disc and adjust it as
required during playback.
CD
AM
FM
1
2
3
EN05-05-KD-S5055[U]f 7/23/03, 6:44 PM5
6
ENGLISH
RADIO OPERATIONS
Listening to the radio
You can use either automatic searching or manual
searching to tune in to a particular station.
Searching a station automatically:
Auto search
1
Select the band (FM 1 – 3, AM).
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to an
FM broadcast.
2
Start searching a station.
When a station is received, searching stops.
Selected band appears
Press
¢ to search
stations of higher
frequencies.
Press 4
to search
stations of lower
frequencies.
To stop searching before a station is received,
press the same button you have pressed for
searching.
Searching a station manually:
Manual search
1
Select the band (FM 1 – 3, AM).
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to an
FM broadcast.
2
Press and hold ¢ or 4
until
“M” (manual) starts flashing on the
display.
MO
RPT RND
MODE
SCM
SSM
CD
AM
FM
Selected
band appears
AM
FM
FM1 FM2
FM3
AM
AM
FM
FM1 FM2
FM3
AM
Lights up when receiving an
FM stereo broadcast with
sufficient signal strength.
EN06-08-KD-S5055U]f 7/23/03, 6:52 PM6
7
ENGLISH
3
Tune in to a station you want while M
(manual) is flashing.
If you release your finger from the button, the
manual mode will automatically turn off after 5
seconds.
If you hold down the button, the frequency keeps
changing (in 50 kHz intervals for FM and 9 kHz
intervals for AM) until you release the button.
When an FM stereo broadcast is hard
to receive:
1 Press MODE to enter the functions mode while
listening to an FM stereo broadcast.
2 Press MO (monaural), while still in the functions
mode, so that the MO indicator lights up on
the display.
Each time you press the button, the MO indicator
lights up and goes off alternately.
When the MO indicator is lit on the display, the
sound you hear becomes monaural but the
reception will be improved.
Storing stations in memory
You can use one of the following two methods to
store broadcasting stations in memory.
Automatic preset of FM stations: SSM (Strong-
station Sequential Memory)
• Manual preset of both FM and AM stations
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM band
(FM1, FM2 and FM3).
1
Select the band (FM1 3) you want
to store FM stations into.
2
Press and hold both buttons for
more than 2 seconds.
Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2 or FM3.)
These stations are preset in the number buttons –
No.1 (lowest frequency) to No.6 (highest frequency).
When automatic preset is over, the station stored
in number button 1 will be automatically tuned in.
Press
¢ to search
stations of higher
frequencies.
Press 4
to search
stations of lower
frequencies.
“SSM” appears, then disappears when automatic
preset is over.
MODE
MO
SSM
FM
FM1 FM2
FM3
MO (monaural) indicator
EN06-08-KD-S5055U]f 7/23/03, 6:52 PM7
8
ENGLISH
MO
RPT RND
7
8
9
10
11
12
Manual preset
You can preset up to 6 stations in each band
(FM1, FM2, FM3 and AM) manually.
Ex: Storing an FM station of 92.5 MHz into the
preset number 1 of the FM1 band.
1
Select the band (FM1 3, AM) you
want to store FM stations into (in
this example, FM1).
Each time you press the button, the FM
band changes as follows:
2
Tune in to a station of 92.5 MHz.
3
Press and hold the number button
(in this example, 1) for more than
2 seconds.
4
Repeat the above procedure to store
other stations into other preset
numbers.
Press
¢
to tune
stations of higher
frequencies.
Press 4
to tune
stations of lower
frequencies.
P1 flashes for a few seconds.
Notes:
A previously preset station is erased when a new station
is stored in the same preset number.
Preset stations are erased when the power supply
to the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset the
stations again.
Tuning in to a preset station
You can easily tune in to a preset station.
Remember that you must store stations first. If you
have not stored them yet, see Storing stations in
memory on page 7 and 8.
1
Select the band (FM1 3, AM).
2
Select the number (1 6) for the preset
station you want.
AM
FM
FM1 FM2
FM3
AM
AM
FM
FM1 FM2
FM3
AM
EN06-08-KD-S5055U]f 7/23/03, 6:52 PM8
9
ENGLISH
Playing a CD
Insert a disc into the loading slot.
The unit turns on, draws
a CD and starts playback
automatically.
Note on One-Touch Operation:
When a CD is already in the loading slot, pressing CD
turns on the unit and starts playback automatically.
All tracks will be played repeatedly until you stop
playback.
CD OPERATIONS
Note:
When a CD is inserted upside down, the CD automa-
tically ejects.
To stop play and eject the CD
Press 0.
CD play stops and the CD automatically ejects
from the loading slot.
If you change the source, the CD play also
stops (without ejecting the CD).
Next time you select “CD” as the source, CD
play starts from where playback has been
stopped previously.
Notes:
If the ejected disc is not removed for about 15 seconds,
the disc is automatically inserted again into the
loading slot to protect it from dust. (CD play will not
start this time.)
You can eject the CD even when the unit is turned off.
Elapsed playing time
Total playing time of
the inserted disc
Total track number of
the inserted disc
Current track
The CD-in indicator lights up
MO
RPT RND
MODE
SCM
AM
FM
SSM
CD
The CD-in indicator flashes
About mistracking:
Mistracking may result from driving on extremely
rough roads. This does not damage the unit and
the CD, but will be annoying.
We recommend that you stop CD play while driving
on such rough roads.
EN09-11-KD-S5055[U]f 9/4/03, 4:30 PM9
10
ENGLISH
Locating a track or a particular
portion on a CD
To fast-forward or reverse the track
To go to the next tracks or the previous
tracks
To go to a particular track directly
Press the number button corresponding to the
track number to start its playback.
To select a track number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
To select a track number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than
1 second.
Press and hold
¢,
while playing a CD, to fast
forward the track.
Press and hold 4
,
while playing a CD, to
reverse the track.
Press
¢
briefly, while
playing a CD, to go ahead
to the beginning of the next
track. Each time you press
the button consecutively,
the beginning of the next
tracks is located and played
back.
Press 4
briefly, while
playing a CD, to go back to
the beginning of the current
track. Each time you press
the button consecutively,
the beginning of the
previous tracks is located
and played back.
Selecting CD playback modes
To play back tracks at random (Random Play)
You can play back all tracks on the CD at random.
1 Press MODE to enter the functions mode
while playing a CD.
2 Press RND (Random), while still in the functions
mode, so that the RND indicator lights up on
the display.
Each time you press the button, CD random
play mode turns on and off alternately.
When the random play is turned on, the RND indi-
cator lights up on the display. A track randomly
selected starts playing.
To play back tracks repeatedly (Repeat Play)
You can play back the current track repeatedly.
1 Press MODE to enter the functions mode
while playing a CD.
2 Press RPT (Repeat), while still in the functions
mode, so that the RPT indicator lights up on
the display.
Each time you press the button, CD repeat
play mode turns on and off alternately.
When the repeat play is turned on, the RPT indicator
lights up on the display. The current track starts
playing repeatedly.
Track number
of the currently
playing track
RPT indicator
RND indicator
MO
RPT RND
7
8
9
10
11
12
RND
MODE
RPT
MODE
EN09-11-KD-S5055[U]f 9/4/03, 4:30 PM10
11
ENGLISH
Prohibiting CD ejection
You can prohibit the CD ejection and can lock a
CD in the loading slot.
While pressing CD, press and hold 0 for
more than 2 seconds.
EJECT flashes on the display for about
5 seconds, and the CD is locked and cannot
be ejected.
To cancel the prohibition and unlock the CD
While pressing CD, press and hold 0 again for
more than 2 seconds.
EJECT appears on the display, and the CD ejects
from the loading slot.
CD
The CD-in indicator flashes
EN09-11-KD-S5055[U]f 9/4/03, 4:30 PM11
12
ENGLISH
SOUND ADJUSTMENTS
Adjusting the sound
You can adjust the sound characteristics to your
preference.
1
Select the item you want to adjust.
Each time you press the
button, the adjustable
items change as follows:
Indication To do: Range
BAS Adjust the bass. –06 (min.)
(Bass) |
+06 (max.)
TRE Adjust the treble. –06 (min.)
(Treble) |
+06 (max.)
FAD Adjust the front R06 (Rear only)
(Fader)* and rear speaker |
balance. F06 (Front only)
BAL Adjust the left L06 (Left only)
(Balance) and right speaker |
balance. R06 (Right only)
VOL Adjust the volume. 00 (min.)
(Volume) |
50 (max.)
* If you are using a two-speaker system, set the fader
level to “00.”
2
Adjust the level
Note:
Normally the + and – buttons work as the volume
control. So you do not have to select “VOL” to adjust
the volume level.
Turning on/off the loudness
function
The human ear is less sensitive to low and high
frequencies at low volumes.
The loudness function can boost these frequencies
to produce well-balanced sound at low volume level.
Each time you press LOUD, the loudness function
turns on and off alternatively.
@A
To increase the level.
To decrease the level.
Ex.: when you adjust TRE (treble)
LOUD (loudness) indicator
EN12-14-KD-S5055[U]f 7/31/03, 1:41 PM12
13
ENGLISH
Recalling the sound modes
When “SCM LINK” is set to “LINK ON,”
select the source.
Each time you change the playback source, the
SCM indicator flashes on the display.
The sound mode stored in memory for the
selected source is recalled.
Notes:
You can adjust each sound mode to your preference,
and store it in memory.
If you want to adjust and store your original sound
mode, see “Storing your own sound adjustments” on
page 14.
To adjust the bass and treble reinforcement levels or
to turn on/off the loudness function temporarily, see
page 12. (Your adjustments will be cancelled if another
source is selected.)
Using the Sound Control
Memory (SCM)
You can select and store a preset sound adjustment
suitable to each playback source. (Advanced SCM)
Selecting and storing the sound modes
Once you select a sound mode, it is stored in
memory. It will be recalled every time you select
the same source and will be shown on the display.
A sound mode can be stored for each of the
following sources — FM1, FM2, FM3, AM, and CD.
If you do not want to store the sound mode
separately for each playback source, but want
to use the same sound mode for all the sources,
see “Canceling Advanced SCM – SCM LINK”
on page 15.
Select the sound mode you want.
Each time you press the button, the sound mode
changes as follows.
When “SCM LINK” is set to “LINK ON”, the
selected sound mode can be stored in memory
for the current source and the effect applies only
to the current source.
When “SCM LINK” is set to “LINK OFF”, the
selected sound mode effect applies to any source.
Indication For: Preset values
BAS TRE
LOUD
SCM OFF (Flat sound) 00 00 ON
BEAT Rock or disco +02 00 ON
music
SOFT Quiet +01 –03 OFF
background
music
POP Light music +04 +01 OFF
SCM
CD
AM
FM
EN12-14-KD-S5055[U]f 7/31/03, 1:41 PM13
14
ENGLISH
Storing your own sound
adjustments
You can adjust the sound modes (BEAT, SOFT,
POP: see page 13) to your preference and store
your own adjustments in memory.
• There is a time limit in doing the following
procedure. If the setting is cancelled before you
finish, start from step 1 again.
1
Call up the sound mode you want to
adjust.
See page 13 for details.
2
Select BAS (bass) or TRE (treble).
3
Adjust the bass or treble level.
See page 12 for details.
4
Repeat steps 2 and 3 to adjust the
other items.
5
To turn on/off the loudness function.
See page 12 for details.
6
Press and hold SCM until the sound
mode you have selected in step 1
flashes on the display.
Your adjustment made for the selected sound
mode is stored in memory.
7
Repeat the same procedure to store
other sound modes.
To reset to the factory settings
Repeat the same procedure and reassign the preset
values listed in the table on page 13.
SCM
SCM
EN12-14-KD-S5055[U]f 7/31/03, 1:41 PM14
15
ENGLISH
OTHER MAIN FUNCTIONS
Setting the clock
1
Press and hold SEL (Select) for more
than 2 seconds.
“CLOCK H”, “CLOCK M”, “SCM LINK” or
“LEVEL” appears on the display.
2
Set the hour.
1 Select “CLOCK H” if not shown on the
display.
2 Adjust the hour.
3
Set the minute.
1 Select “CLOCK M.”
2 Adjust the minute.
4
Press SEL (select) to finish the setting.
21
During tuner operation:
During CD operation:
Clock
Frequency
Clock
Elapsed playing time
To check the current clock time (changing the
display mode)
Press DISP repeatedly. Each time you press the
button, the display mode changes as follows.
Cancelling Advanced SCM
– SCM LINK
You can cancel the Advanced SCM (Sound Control
Memory), and unlink the sound modes and the
playback sources.
When shipped from the factory, a different sound
mode can be stored in memory for each source so
that you can change the sound modes simply by
changing the sources.
LINK ON: Advanced SCM (different SCM for
different sources)
LINK OFF: Conventional SCM (one SCM for all
sources)
1
Press and hold SEL (select) for more
than 2 seconds.
“CLOCK H”, “CLOCK M”, “SCM LINK” or
“LEVEL” appears on the display.
2
Select “SCM LINK” if not shown on the
display.
3
Select the desire mode — “LINK ON”
or “LINK OFF”.
4
Press SEL (select) to finish the setting.
If the unit is not in use when you press DISP, the
power turns on, the clock time is shown for
5 seconds, then the power turns off.
2
1
EN15-17-KD-S5055[U]f 7/31/03, 1:43 PM15
16
ENGLISH
3
Select the desired mode — “VOL 1”,
“VOL 2” or “OFF”.
4
Press SEL (select) to finish the setting.
Selecting the level display
You can select the level display according to your
preference.
When shipped from the factory, “VOL 2” is selected.
VOL 1 : Shows the volume level indicator.
VOL 2 : Alternates “VOL 1” setting and
illumination display.
OFF : Erases the volume level indicator.
1
Press and hold SEL (Select) for more
than 2 seconds.
“CLOCK H”, “CLOCK M”, “SCM LINK” or
“LEVEL” appears on the display.
2
Select “LEVEL” if not shown on the
display.
EN15-17-KD-S5055[U]f 9/2/03, 5:13 PM16
17
ENGLISH
Note on cleaning the connectors:
If you frequently detach the control panel, the
connectors will deteriorate.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened
with alcohol, being careful not to damage the
connectors.
Connectors
Detaching the control panel
You can detach the control panel when leaving the
car.
When detaching or attaching the control panel, be
careful not to damage the connectors on the back
of the control panel and on the panel holder.
Detaching the control panel
Before detaching the control panel, be sure to
turn off the power.
1
Unlock the control panel.
2
Lift and pull the control panel out of
the unit.
3
Put the detached control panel into
the case provided.
Attaching the control panel
1
Insert the left side of the control panel
into the groove on the panel holder.
2
Press the right side of the control
panel to fix it to the panel holder.
EN15-17-KD-S5055[U]f 7/31/03, 1:51 PM17
18
ENGLISH
MAINTENANCE
Handling discs
This unit has been designed to reproduce CDs
and CD-Rs (Recordable).
This unit is not compatible with MP3 discs.
How to handle discs
When removing a disc from
its case, press down the
center holder of the case
and lift the disc out,
holding it by the edges.
Always hold the disc by the edges.
Do not touch its recording surface.
When storing a disc into its case, gently insert
the disc around the center holder (with the
printed surface facing up).
Make sure to store discs into the cases after use.
To keep discs clean
A dirty disc may not play correctly.
If a disc does become dirty,
wipe it with a soft cloth in
a straight line from center
to edge.
To play new discs
New discs may have some
rough spots around the inner
and outer edges. If such a
disc is used, this unit may
reject the disc. To remove
these rough spots, rub the
edges with a pencil or ball-point
pen, etc.
Moisture condensation
Moisture may condense on the lens inside the
unit in the following cases:
After starting the heater in the car.
If it becomes very humid inside the car.
Should this occur, the unit may malfunction. In
this case, eject the disc and leave the unit
turned on for a few hours until the moisture
evaporates.
Center holder
When playing a CD-R
Before playing back CD-Rs, read their
instructions or cautions carefully.
Use only “finalized” CD-Rs.
Some CD-Rs may not play back on this unit
because of their disc characteristics, and for
the following reasons:
Discs are dirty or scratched.
Moisture condensation on the lens inside
the unit.
The pickup lens inside the unit is dirty.
CD-Rs are susceptible to high temperatures or
high humidity, so do not leave them inside
your car.
Do not use following CD-Rs:
Discs with stickers, labels, or protective seal
stuck to the surface.
Discs on which labels can be directly printed
by an ink jet printer.
Using these discs under high temperatures or
high humidity may cause malfunctions or damage
to discs For example,
Stickers or labels may shrink and warp a disc.
Stickers or lables may peel off so discs
cannot be ejected.
Print on discs may get sticky.
Read instructions or cautions about labels and
printable discs carefully.
CD-RWs (Rewritable) cannot be played back
on this unit.
CAUTIONS:
Do not insert 8 cm discs (single CDs) into the
loading slot. (Such discs cannot be ejected.)
Do not insert any disc of unusual shape — like a
heart or flower; otherwise, it will cause a
malfunction.
Do not expose discs to direct sunlight or any heat
source or place them in a place subject to high
temperature and humidity. Do not leave them in
a car.
Do not use any solvent (for example, conventional
record cleaner, spray, thinner, benzine, etc.) to
clean discs.
Sticker
Warped
disc
Disc
Stick-on
label
Stick
residue
EN18-20-KD-S5055[U]f 9/2/03, 5:18 PM18
19
ENGLISH
TROUBLESHOOTING
What appears to be trouble is not always serious. Check the following points before calling a service
center.
Symptoms Causes Remedies
Sound cannot be heard The volume level is set to the Adjust it to the optimum level.
from the speakers. minimum level.
Connections are incorrect. Check the cords and
connections.
This unit does not work at The built-in microcomputer While holding SEL (Select),
all. may have functioned press
(Standby/
incorrectly due to noise, etc. On Attenuator) for more
than 2 seconds to reset the unit.
(The clock setting and preset
stations stored in memory are
erased) (See page 2)
SSM (Strong-station Signals are too weak. Store stations manually.
Sequential Memory)
automatic preset does not
work.
Static noise while listening The antenna is not connected Connect the antenna firmly.
to the radio. firmly.
CD automatically ejects. CD is inserted upside down. Insert the CD correctly.
CD-R cannot be played CD-R is not finalized. Insert a finalized CD-R.
back.
Tracks on the CD-R cannot Finalize the CD-R with the
be skipped. component which you used
for recording.
CD can be neither played CD is locked. Unlocked the CD. (See page 11)
back nor ejected.
The CD player may have While holding
functioned incorrectly. (Standby/On Attenuator), press
/ (Eject) for more than 2 seconds.
Be careful not to drop the CD
when it is ejected.
CD sound is sometimes You are driving on rough Stop playback while driving on
interrupted. roads. rough roads.
CD is scratched. Change the CD.
Connections are incorrect. Check the cords and
connections.
“NO DISC” appears on the No CD in the loading slot. Insert a CD into the loading slot.
display.
CD is inserted incorrectly. Insert the CD correctly.
General
FM/AM
CD Playback
EN18-20-KD-S5055[U]f 7/31/03, 1:45 PM19
20
ENGLISH
SPECIFICATIONS
AUDIO AMPLIFIER SECTION
Maximum Power Output:
Front: 45 watts per channel
Rear: 45 watts per channel
Continuous Power Output (RMS):
Front: 17 watts per channel into 4 ,
40 Hz to 20 000 Hz at no more than
0.8% total harmonic distortion.
Rear: 17 watts per channel into 4 ,
40 Hz to 20 000 Hz at no more than
0.8% total harmonic distortion.
Load Impedance: 4 (4 to 8 allowance)
Tone Control Range
Bass: ±10 dB at 100 Hz
Treble: ±10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance: 2.0 V/20 k load
(full scale)
Output Impedance: 1 k
TUNER SECTION
Frequency Range
FM: 87.5 MHz to 108.0 MHz
AM: 531 kHz to 1 602 kHz
[FM Tuner]
Usable Sensitivity: 11.3 dBf (1.0 µV/75 )
50 dB Quieting Sensitivity:
16.3 dBf (1.8 µV/75 )
Alternate Channel Selectivity (400 kHz):
65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 35 dB
Capture Ratio: 1.5 dB
[AM Tuner]
Sensitivity: 20 µV
Selectivity: 35 dB
CD PLAYER SECTION
Type: Compact disc player
Signal Detection System: Non-contact optical
pickup (semiconductor laser)
Number of channels: 2 channels (stereo)
Frequency Response: 5 Hz to 20 000 Hz
Dynamic Range: 90 dB
Signal-to-Noise Ratio: 95 dB
Wow and Flutter: Less than measurable limit
GENERAL
Power Requirement
Operating Voltage: DC 14.4 volts (11 volts to 16
volts allowance)
Allowable Working Temperature:
0°C to +40°C
Grounding System: Negative ground
Dimensions (W x H x D)
Installation Size:
182 mm x 52 mm x 150 mm
Panel Size: 188 mm x 58 mm x 11 mm
Mass: 1.3 kg (excluding accessories)
Design and specifications are subject to change
without notice.
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
EN18-20-KD-S5055[U]f 7/23/03, 7:27 PM20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78

JVC CD Player GET0172-001A Manuale utente

Categoria
Ricevitori multimediali per auto
Tipo
Manuale utente
Questo manuale è adatto anche per

in altre lingue