JVC GET0172-001A Manuale utente

ENGLISH



‰∑¬

CD RECEIVER KD-S5055

‡§√◊ËÕß‡≈Ëπ

CD KD-S5055

GET0172-001A

[U]

LOUD

SEL

D

IS

P

DIRECT TRACK ACCESS

KD-S5055

CD  !" KD-S5055

For installation and connections, refer to the separate manual.

 !"#$%&'()* !"

°√ÿ≥“¥Ÿ§ŸË¡◊Õ∑’Ë·¬°µË“ßÀ“° „π°“√µ‘¥µ—Èß·≈–°“√‡™◊ËÕ¡µËÕ

INSTRUCTIONS

 !"

§”·π–π”

ENCOVER-KD-S5055[U]f 8/1/03, 10:56 AM1

2

ENGLISH

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside unit; leave all

servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid

direct exposure to beam.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

How to reset your unit

While holding SEL (Select), press (Standby/On Attenuator) for more than 2 seconds.

This will reset the built-in microcomputer.

NOTES:

• Your preset adjustments — such as preset channels or sound adjustments — will also be erased.

• If a CD is in the unit, it will eject when you reset the unit. Be careful not to drop the CD.

(Standby/On Attenuator)

SEL (Select)

LOUD

SEL

D

I

S

P

EN02-03-KD-S5055[U]f 7/31/03, 1:35 PM2

3

ENGLISH

How to use the MODE button

If you press MODE, the unit goes into functions mode and the number buttons work as different

function buttons.

To use these buttons as number buttons again after pressing MODE, wait for 5 seconds without

pressing any number button until the functions mode is cleared.

• Pressing MODE again also clears the functions mode.

CONTENTS

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

How to reset your unit .................................. 2

How to use the MODE button ...................... 3

LOCATION OF THE BUTTONS ...............4

Control panel ............................................... 4

BASIC OPERATIONS ..........................5

Turning on the power ................................... 5

RADIO OPERATIONS .........................6

Listening to the radio ................................... 6

Storing stations in memory .......................... 7

Tuning in to a preset station ........................ 8

CD OPERATIONS ..............................9

Playing a CD ................................................ 9

Locating a track or a particular portion

on a CD .................................................. 10

Selecting CD playback modes ................... 10

Prohibiting CD ejection .............................. 11

SOUND ADJUSTMENTS .................... 12

Adjusting the sound ................................... 12

Turning on/off the loudness function ............. 12

Using the Sound Control Memory (SCM) .. 13

Storing your own sound adjustments ........ 14

OTHER MAIN FUNCTIONS ................. 15

Setting the clock ........................................ 15

Canceling Advanced SCM – SCM LINK .... 15

Selecting the level display ......................... 16

Detaching the control panel ....................... 17

MAINTENANCE .............................. 18

Handling discs ........................................... 18

TROUBLESHOOTING ....................... 19

SPECIFICATIONS ............................ 20

BEFORE USE

*

For safety....

• Do not raise the volume level too much, as this

will block outside sounds, making driving

dangerous.

• Stop the car before performing any complicated

operations.

*

Temperature inside the car....

If you have parked the car for a long time in hot

or cold weather, wait until the temperature in the

car becomes normal before operating the unit.

Time countdown indicator

MODE

MO

RPT RND

7

8

9

10

11

12

EN02-03-KD-S5055[U]f 7/31/03, 1:35 PM3

ENGLISH

4

DIRECT TRACK ACCESS

MO

RPT RND

MODE

SCM

CD

AM

FM

SSM

1

2

3

4

9

8

76

t

w

p

o

;

a

s

d

f g

h

k

j

5

q

e r

i

uy

LOCATION OF THE BUTTONS

1 (Standby/On Attenuator) button

2 +/– buttons

3 LOUD (Loudness) button

4 SEL (Select) button

5 Loading slot

6 AM button

7 0 (Eject) button

8 CD button

9 FM button

p DISP (Display) button

q MO (Monaural) button

w RPT (Repeat) button

e RND (Random) button

r Number buttons

t MODE button

y SCM (Sound Control Memory) button

u

(Control panel release) button

i 4

/ ¢ buttons

• Also functions as SSM buttons when

pressed together.

Display window

o SCM (Sound Control Memory) indicator

; CD indicator

a Band indicators

FM1, FM2, FM3

AM

s Tuner reception indicators

MO (Monaural), ST (Stereo)

d RND (Random) indicator

f RPT (Repeat) indicator

g LOUD indicator

h CD-in indicator

j Main display

k Volume level indicator

Control panel

Display window

EN04-04-KD-S5055[U]f 7/31/03, 1:36 PM4

5

ENGLISH

SCM

MO

RPT RND

MODE

SSM

CD

AM

FM

4

Adjust the sound as you want

(see pages 12 – 14).

To drop the volume in a moment

Press briefly while listening to any

source. “ATT” starts flashing on the display, and

the volume level will drop in a moment.

To resume the previous volume level, press the

button briefly again.

To turn off the power

Press and hold until “SEE YOU”

appears on the display.

Note:

When you use this unit for the first time, set the built-in

clock correctly, see page 15.

Turning on the power

1

Turn on the power.

Note on One-Touch Operation:

When you select a source in step 2 below, the

power automatically comes on. You do not have

to press this button to turn on the power.

2

Select the source.

3

Adjust the volume.

BASIC OPERATIONS

Volume level indicator

(see page 16)

Volume level appears

To increase the volume.

To decrease the volume.

To operate the tuner (FM or AM),

see pages 6 – 8.

To operate the CD,

see pages 9 – 11.

CAUTION on volume setting

CDs produce very little noise compared with other

sources. If the volume level is adjusted for the tuner,

for example, the speakers may be damaged by the

sudden increase in the output level. Therefore, lower

the volume before playing a disc and adjust it as

required during playback.

CD

AM

FM

1

2

3

EN05-05-KD-S5055[U]f 7/23/03, 6:44 PM5

6

ENGLISH

RADIO OPERATIONS

Listening to the radio

You can use either automatic searching or manual

searching to tune in to a particular station.

Searching a station automatically:

Auto search

1

Select the band (FM 1 – 3, AM).

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to an

FM broadcast.

2

Start searching a station.

When a station is received, searching stops.

Selected band appears

Press

¢ to search

stations of higher

frequencies.

Press 4

to search

stations of lower

frequencies.

To stop searching before a station is received,

press the same button you have pressed for

searching.

Searching a station manually:

Manual search

1

Select the band (FM 1 – 3, AM).

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to an

FM broadcast.

2

Press and hold ¢ or 4

until

“M” (manual) starts flashing on the

display.

MO

RPT RND

MODE

SCM

SSM

CD

AM

FM

Selected

band appears

AM

FM

FM1 FM2

FM3

AM

FM

FM1 FM2

FM3

AM

Lights up when receiving an

FM stereo broadcast with

sufficient signal strength.

EN06-08-KD-S5055U]f 7/23/03, 6:52 PM6

7

ENGLISH

3

Tune in to a station you want while “M”

(manual) is flashing.

• If you release your finger from the button, the

manual mode will automatically turn off after 5

seconds.

• If you hold down the button, the frequency keeps

changing (in 50 kHz intervals for FM and 9 kHz

intervals for AM) until you release the button.

When an FM stereo broadcast is hard

to receive:

1 Press MODE to enter the functions mode while

listening to an FM stereo broadcast.

2 Press MO (monaural), while still in the functions

mode, so that the MO indicator lights up on

the display.

Each time you press the button, the MO indicator

lights up and goes off alternately.

When the MO indicator is lit on the display, the

sound you hear becomes monaural but the

reception will be improved.

Storing stations in memory

You can use one of the following two methods to

store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strong-

station Sequential Memory)

• Manual preset of both FM and AM stations

FM station automatic preset: SSM

You can preset 6 local FM stations in each FM band

(FM1, FM2 and FM3).

1

Select the band (FM1 – 3) you want

to store FM stations into.

2

Press and hold both buttons for

more than 2 seconds.

Local FM stations with the strongest signals are

searched and stored automatically in the band

number you have selected (FM1, FM2 or FM3.)

These stations are preset in the number buttons –

No.1 (lowest frequency) to No.6 (highest frequency).

When automatic preset is over, the station stored

in number button 1 will be automatically tuned in.

Press

¢ to search

stations of higher

frequencies.

Press 4

to search

stations of lower

frequencies.

“SSM” appears, then disappears when automatic

preset is over.

MODE

MO

SSM

FM

FM1 FM2

FM3

MO (monaural) indicator

EN06-08-KD-S5055U]f 7/23/03, 6:52 PM7

8

ENGLISH

MO

RPT RND

7

8

9

10

11

12

Manual preset

You can preset up to 6 stations in each band

(FM1, FM2, FM3 and AM) manually.

Ex: Storing an FM station of 92.5 MHz into the

preset number 1 of the FM1 band.

1

Select the band (FM1 – 3, AM) you

want to store FM stations into (in

this example, FM1).

• Each time you press the button, the FM

band changes as follows:

2

Tune in to a station of 92.5 MHz.

3

Press and hold the number button

(in this example, 1) for more than

2 seconds.

4

Repeat the above procedure to store

other stations into other preset

numbers.

Press

¢

to tune

stations of higher

frequencies.

Press 4

to tune

stations of lower

frequencies.

“P1” flashes for a few seconds.

Notes:

• A previously preset station is erased when a new station

is stored in the same preset number.

• Preset stations are erased when the power supply

to the memory circuit is interrupted (for example,

during battery replacement). If this occurs, preset the

stations again.

Tuning in to a preset station

You can easily tune in to a preset station.

Remember that you must store stations first. If you

have not stored them yet, see “Storing stations in

memory” on page 7 and 8.

1

Select the band (FM1 – 3, AM).

2

Select the number (1 – 6) for the preset

station you want.

AM

FM

FM1 FM2

FM3

AM

FM

FM1 FM2

FM3

AM

EN06-08-KD-S5055U]f 7/23/03, 6:52 PM8

9

ENGLISH

Playing a CD

Insert a disc into the loading slot.

The unit turns on, draws

a CD and starts playback

automatically.

Note on One-Touch Operation:

When a CD is already in the loading slot, pressing CD

turns on the unit and starts playback automatically.

All tracks will be played repeatedly until you stop

playback.

CD OPERATIONS

Note:

When a CD is inserted upside down, the CD automa-

tically ejects.

To stop play and eject the CD

Press 0.

CD play stops and the CD automatically ejects

from the loading slot.

• If you change the source, the CD play also

stops (without ejecting the CD).

Next time you select “CD” as the source, CD

play starts from where playback has been

stopped previously.

Notes:

• If the ejected disc is not removed for about 15 seconds,

the disc is automatically inserted again into the

loading slot to protect it from dust. (CD play will not

start this time.)

• You can eject the CD even when the unit is turned off.

Elapsed playing time

Total playing time of

the inserted disc

Total track number of

the inserted disc

Current track

The CD-in indicator lights up

MO

RPT RND

MODE

SCM

AM

FM

SSM

CD

The CD-in indicator flashes

About mistracking:

Mistracking may result from driving on extremely

rough roads. This does not damage the unit and

the CD, but will be annoying.

We recommend that you stop CD play while driving

on such rough roads.

EN09-11-KD-S5055[U]f 9/4/03, 4:30 PM9

10

ENGLISH

Locating a track or a particular

portion on a CD

To fast-forward or reverse the track

To go to the next tracks or the previous

tracks

To go to a particular track directly

Press the number button corresponding to the

track number to start its playback.

• To select a track number from 1 – 6:

Press 1 (7) – 6 (12) briefly.

• To select a track number from 7 – 12:

Press and hold 1 (7) – 6 (12) for more than

1 second.

Press and hold

¢,

while playing a CD, to fast

forward the track.

Press and hold 4

,

while playing a CD, to

reverse the track.

Press

¢

briefly, while

playing a CD, to go ahead

to the beginning of the next

track. Each time you press

the button consecutively,

the beginning of the next

tracks is located and played

back.

Press 4

briefly, while

playing a CD, to go back to

the beginning of the current

track. Each time you press

the button consecutively,

the beginning of the

previous tracks is located

and played back.

Selecting CD playback modes

To play back tracks at random (Random Play)

You can play back all tracks on the CD at random.

1 Press MODE to enter the functions mode

while playing a CD.

2 Press RND (Random), while still in the functions

mode, so that the RND indicator lights up on

the display.

Each time you press the button, CD random

play mode turns on and off alternately.

When the random play is turned on, the RND indi-

cator lights up on the display. A track randomly

selected starts playing.

To play back tracks repeatedly (Repeat Play)

You can play back the current track repeatedly.

1 Press MODE to enter the functions mode

while playing a CD.

2 Press RPT (Repeat), while still in the functions

mode, so that the RPT indicator lights up on

the display.

Each time you press the button, CD repeat

play mode turns on and off alternately.

When the repeat play is turned on, the RPT indicator

lights up on the display. The current track starts

playing repeatedly.

Track number

of the currently

playing track

RPT indicator

RND indicator

MO

RPT RND

7

8

9

10

11

12

RND

MODE

RPT

MODE

EN09-11-KD-S5055[U]f 9/4/03, 4:30 PM10

11

ENGLISH

Prohibiting CD ejection

You can prohibit the CD ejection and can lock a

CD in the loading slot.

While pressing CD, press and hold 0 for

more than 2 seconds.

“EJECT” flashes on the display for about

5 seconds, and the CD is locked and cannot

be ejected.

To cancel the prohibition and unlock the CD

While pressing CD, press and hold 0 again for

more than 2 seconds.

“EJECT” appears on the display, and the CD ejects

from the loading slot.

CD

The CD-in indicator flashes

EN09-11-KD-S5055[U]f 9/4/03, 4:30 PM11

12

ENGLISH

SOUND ADJUSTMENTS

Adjusting the sound

You can adjust the sound characteristics to your

preference.

1

Select the item you want to adjust.

Each time you press the

button, the adjustable

items change as follows:

Indication To do: Range

BAS Adjust the bass. –06 (min.)

(Bass) |

+06 (max.)

TRE Adjust the treble. –06 (min.)

(Treble) |

+06 (max.)

FAD Adjust the front R06 (Rear only)

(Fader)* and rear speaker |

balance. F06 (Front only)

BAL Adjust the left L06 (Left only)

(Balance) and right speaker |

balance. R06 (Right only)

VOL Adjust the volume. 00 (min.)

(Volume) |

50 (max.)

* If you are using a two-speaker system, set the fader

level to “00.”

2

Adjust the level

Note:

Normally the + and – buttons work as the volume

control. So you do not have to select “VOL” to adjust

the volume level.

Turning on/off the loudness

function

The human ear is less sensitive to low and high

frequencies at low volumes.

The loudness function can boost these frequencies

to produce well-balanced sound at low volume level.

Each time you press LOUD, the loudness function

turns on and off alternatively.

@A

To increase the level.

To decrease the level.

Ex.: when you adjust “TRE” (treble)

LOUD (loudness) indicator

EN12-14-KD-S5055[U]f 7/31/03, 1:41 PM12

13

ENGLISH

Recalling the sound modes

When “SCM LINK” is set to “LINK ON,”

select the source.

Each time you change the playback source, the

SCM indicator flashes on the display.

The sound mode stored in memory for the

selected source is recalled.

Notes:

• You can adjust each sound mode to your preference,

and store it in memory.

If you want to adjust and store your original sound

mode, see “Storing your own sound adjustments” on

page 14.

• To adjust the bass and treble reinforcement levels or

to turn on/off the loudness function temporarily, see

page 12. (Your adjustments will be cancelled if another

source is selected.)

Using the Sound Control

Memory (SCM)

You can select and store a preset sound adjustment

suitable to each playback source. (Advanced SCM)

Selecting and storing the sound modes

Once you select a sound mode, it is stored in

memory. It will be recalled every time you select

the same source and will be shown on the display.

A sound mode can be stored for each of the

following sources — FM1, FM2, FM3, AM, and CD.

• If you do not want to store the sound mode

separately for each playback source, but want

to use the same sound mode for all the sources,

see “Canceling Advanced SCM – SCM LINK”

on page 15.

Select the sound mode you want.

• Each time you press the button, the sound mode

changes as follows.

• When “SCM LINK” is set to “LINK ON”, the

selected sound mode can be stored in memory

for the current source and the effect applies only

to the current source.

• When “SCM LINK” is set to “LINK OFF”, the

selected sound mode effect applies to any source.

Indication For: Preset values

BAS TRE

LOUD

SCM OFF (Flat sound) 00 00 ON

BEAT Rock or disco +02 00 ON

music

SOFT Quiet +01 –03 OFF

background

music

POP Light music +04 +01 OFF

SCM

CD

AM

FM

EN12-14-KD-S5055[U]f 7/31/03, 1:41 PM13

14

ENGLISH

Storing your own sound

adjustments

You can adjust the sound modes (BEAT, SOFT,

POP: see page 13) to your preference and store

your own adjustments in memory.

• There is a time limit in doing the following

procedure. If the setting is cancelled before you

finish, start from step 1 again.

1

Call up the sound mode you want to

adjust.

See page 13 for details.

2

Select “BAS” (bass) or “TRE” (treble).

3

Adjust the bass or treble level.

See page 12 for details.

4

Repeat steps 2 and 3 to adjust the

other items.

5

To turn on/off the loudness function.

See page 12 for details.

6

Press and hold SCM until the sound

mode you have selected in step 1

flashes on the display.

Your adjustment made for the selected sound

mode is stored in memory.

7

Repeat the same procedure to store

other sound modes.

To reset to the factory settings

Repeat the same procedure and reassign the preset

values listed in the table on page 13.

SCM

EN12-14-KD-S5055[U]f 7/31/03, 1:41 PM14

15

ENGLISH

OTHER MAIN FUNCTIONS

Setting the clock

1

Press and hold SEL (Select) for more

than 2 seconds.

“CLOCK H”, “CLOCK M”, “SCM LINK” or

“LEVEL” appears on the display.

2

Set the hour.

1 Select “CLOCK H” if not shown on the

display.

2 Adjust the hour.

3

Set the minute.

1 Select “CLOCK M.”

2 Adjust the minute.

4

Press SEL (select) to finish the setting.

21

During tuner operation:

During CD operation:

Clock

Frequency

Clock

Elapsed playing time

To check the current clock time (changing the

display mode)

Press DISP repeatedly. Each time you press the

button, the display mode changes as follows.

Cancelling Advanced SCM

– SCM LINK

You can cancel the Advanced SCM (Sound Control

Memory), and unlink the sound modes and the

playback sources.

When shipped from the factory, a different sound

mode can be stored in memory for each source so

that you can change the sound modes simply by

changing the sources.

LINK ON: Advanced SCM (different SCM for

different sources)

LINK OFF: Conventional SCM (one SCM for all

sources)

1

Press and hold SEL (select) for more

than 2 seconds.

“CLOCK H”, “CLOCK M”, “SCM LINK” or

“LEVEL” appears on the display.

2

Select “SCM LINK” if not shown on the

display.

3

Select the desire mode — “LINK ON”

or “LINK OFF”.

4

Press SEL (select) to finish the setting.

• If the unit is not in use when you press DISP, the

power turns on, the clock time is shown for

5 seconds, then the power turns off.

2

1

EN15-17-KD-S5055[U]f 7/31/03, 1:43 PM15

16

ENGLISH

3

Select the desired mode — “VOL 1”,

“VOL 2” or “OFF”.

4

Press SEL (select) to finish the setting.

Selecting the level display

You can select the level display according to your

preference.

When shipped from the factory, “VOL 2” is selected.

VOL 1 : Shows the volume level indicator.

VOL 2 : Alternates “VOL 1” setting and

illumination display.

OFF : Erases the volume level indicator.

1

Press and hold SEL (Select) for more

than 2 seconds.

“CLOCK H”, “CLOCK M”, “SCM LINK” or

“LEVEL” appears on the display.

2

Select “LEVEL” if not shown on the

display.

EN15-17-KD-S5055[U]f 9/2/03, 5:13 PM16

17

ENGLISH

Note on cleaning the connectors:

If you frequently detach the control panel, the

connectors will deteriorate.

To minimize this possibility, periodically wipe the

connectors with a cotton swab or cloth moistened

with alcohol, being careful not to damage the

connectors.

Connectors

Detaching the control panel

You can detach the control panel when leaving the

car.

When detaching or attaching the control panel, be

careful not to damage the connectors on the back

of the control panel and on the panel holder.

Detaching the control panel

Before detaching the control panel, be sure to

turn off the power.

1

Unlock the control panel.

2

Lift and pull the control panel out of

the unit.

3

Put the detached control panel into

the case provided.

Attaching the control panel

1

Insert the left side of the control panel

into the groove on the panel holder.

2

Press the right side of the control

panel to fix it to the panel holder.

EN15-17-KD-S5055[U]f 7/31/03, 1:51 PM17

18

ENGLISH

MAINTENANCE

Handling discs

This unit has been designed to reproduce CDs

and CD-Rs (Recordable).

• This unit is not compatible with MP3 discs.

How to handle discs

When removing a disc from

its case, press down the

center holder of the case

and lift the disc out,

holding it by the edges.

• Always hold the disc by the edges.

Do not touch its recording surface.

When storing a disc into its case, gently insert

the disc around the center holder (with the

printed surface facing up).

• Make sure to store discs into the cases after use.

To keep discs clean

A dirty disc may not play correctly.

If a disc does become dirty,

wipe it with a soft cloth in

a straight line from center

to edge.

To play new discs

New discs may have some

rough spots around the inner

and outer edges. If such a

disc is used, this unit may

reject the disc. To remove

these rough spots, rub the

edges with a pencil or ball-point

pen, etc.

Moisture condensation

Moisture may condense on the lens inside the

unit in the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car.

Should this occur, the unit may malfunction. In

this case, eject the disc and leave the unit

turned on for a few hours until the moisture

evaporates.

Center holder

When playing a CD-R

Before playing back CD-Rs, read their

instructions or cautions carefully.

• Use only “finalized” CD-Rs.

• Some CD-Rs may not play back on this unit

because of their disc characteristics, and for

the following reasons:

– Discs are dirty or scratched.

– Moisture condensation on the lens inside

the unit.

– The pickup lens inside the unit is dirty.

• CD-Rs are susceptible to high temperatures or

high humidity, so do not leave them inside

your car.

• Do not use following CD-Rs:

– Discs with stickers, labels, or protective seal

stuck to the surface.

– Discs on which labels can be directly printed

by an ink jet printer.

Using these discs under high temperatures or

high humidity may cause malfunctions or damage

to discs For example,

– Stickers or labels may shrink and warp a disc.

– Stickers or lables may peel off so discs

cannot be ejected.

– Print on discs may get sticky.

Read instructions or cautions about labels and

printable discs carefully.

• CD-RWs (Rewritable) cannot be played back

on this unit.

CAUTIONS:

• Do not insert 8 cm discs (single CDs) into the

loading slot. (Such discs cannot be ejected.)

• Do not insert any disc of unusual shape — like a

heart or flower; otherwise, it will cause a

malfunction.

• Do not expose discs to direct sunlight or any heat

source or place them in a place subject to high

temperature and humidity. Do not leave them in

a car.

• Do not use any solvent (for example, conventional

record cleaner, spray, thinner, benzine, etc.) to

clean discs.

Sticker

Warped

disc

Disc

Stick-on

label

Stick

residue

EN18-20-KD-S5055[U]f 9/2/03, 5:18 PM18

19

ENGLISH

TROUBLESHOOTING

What appears to be trouble is not always serious. Check the following points before calling a service

center.

Symptoms Causes Remedies

• Sound cannot be heard The volume level is set to the Adjust it to the optimum level.

from the speakers. minimum level.

Connections are incorrect. Check the cords and

connections.

• This unit does not work at The built-in microcomputer While holding SEL (Select),

all. may have functioned press

(Standby/

incorrectly due to noise, etc. On Attenuator) for more

than 2 seconds to reset the unit.

(The clock setting and preset

stations stored in memory are

erased) (See page 2)

• SSM (Strong-station Signals are too weak. Store stations manually.

Sequential Memory)

automatic preset does not

work.

• Static noise while listening The antenna is not connected Connect the antenna firmly.

to the radio. firmly.

• CD automatically ejects. CD is inserted upside down. Insert the CD correctly.

• CD-R cannot be played CD-R is not finalized. • Insert a finalized CD-R.

back.

• Tracks on the CD-R cannot • Finalize the CD-R with the

be skipped. component which you used

for recording.

• CD can be neither played CD is locked. Unlocked the CD. (See page 11)

back nor ejected.

The CD player may have While holding

functioned incorrectly. (Standby/On Attenuator), press

/ (Eject) for more than 2 seconds.

Be careful not to drop the CD

when it is ejected.

• CD sound is sometimes You are driving on rough Stop playback while driving on

interrupted. roads. rough roads.

CD is scratched. Change the CD.

Connections are incorrect. Check the cords and

connections.

• “NO DISC” appears on the No CD in the loading slot. Insert a CD into the loading slot.

display.

CD is inserted incorrectly. Insert the CD correctly.

General

FM/AM

CD Playback

EN18-20-KD-S5055[U]f 7/31/03, 1:45 PM19

20

ENGLISH

SPECIFICATIONS

AUDIO AMPLIFIER SECTION

Maximum Power Output:

Front: 45 watts per channel

Rear: 45 watts per channel

Continuous Power Output (RMS):

Front: 17 watts per channel into 4 Ω,

40 Hz to 20 000 Hz at no more than

0.8% total harmonic distortion.

Rear: 17 watts per channel into 4 Ω,

40 Hz to 20 000 Hz at no more than

0.8% total harmonic distortion.

Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)

Tone Control Range

Bass: ±10 dB at 100 Hz

Treble: ±10 dB at 10 kHz

Frequency Response: 40 Hz to 20 000 Hz

Signal-to-Noise Ratio: 70 dB

Line-Out Level/Impedance: 2.0 V/20 kΩ load

(full scale)

Output Impedance: 1 kΩ

TUNER SECTION

Frequency Range

FM: 87.5 MHz to 108.0 MHz

AM: 531 kHz to 1 602 kHz

[FM Tuner]

Usable Sensitivity: 11.3 dBf (1.0 µV/75 Ω)

50 dB Quieting Sensitivity:

16.3 dBf (1.8 µV/75 Ω)

Alternate Channel Selectivity (400 kHz):

65 dB

Frequency Response: 40 Hz to 15 000 Hz

Stereo Separation: 35 dB

Capture Ratio: 1.5 dB

[AM Tuner]

Sensitivity: 20 µV

Selectivity: 35 dB

CD PLAYER SECTION

Type: Compact disc player

Signal Detection System: Non-contact optical

pickup (semiconductor laser)

Number of channels: 2 channels (stereo)

Frequency Response: 5 Hz to 20 000 Hz

Dynamic Range: 90 dB

Signal-to-Noise Ratio: 95 dB

Wow and Flutter: Less than measurable limit

GENERAL

Power Requirement

Operating Voltage: DC 14.4 volts (11 volts to 16

volts allowance)

Allowable Working Temperature:

0°C to +40°C

Grounding System: Negative ground

Dimensions (W x H x D)

Installation Size:

182 mm x 52 mm x 150 mm

Panel Size: 188 mm x 58 mm x 11 mm

Mass: 1.3 kg (excluding accessories)

Design and specifications are subject to change

without notice.

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

EN18-20-KD-S5055[U]f 7/23/03, 7:27 PM20

La pagina sta caricando ...

JVC GET0172-001A Manuale utente

Questo manuale è adatto anche per

JVC GET0172-001A Manuale utente

in altre lingue

Documenti correlati

Altri documenti