Panasonic Diga DMR-ES10 Istruzioni per l'uso

Marca: Panasonic

Modello: Diga DMR-ES10

Categoria: Lettori DVD

Tipo: Istruzioni per l'uso

Questo manuale è adatto anche per

DMRES10

RQT8020-3L

Operating Instructions

DVD Recorder

DMR-ES10

Model No.

EG GN GC GCS

For Asia

For Continental Europe

For Australia and N.Z.

Dear customer

Thank you for purchasing this product. For optimum

performance and safety, please read these

instructions carefully.

Before connecting, operating or adjusting this

product, please read the instructions completely.

Please keep this manual for future reference.

Region number supported by

this unit

Region numbers are allocated to DVD players

and DVD-Video according to where they are

sold.

For Continental Europe and

Middle East

• The region number of this unit is “2”.

• The unit will play DVD-Video marked with

labels containing “2” or “ALL”.

Example:

For Asia

• The region number of this unit is “3”.

• The unit will play DVD-Video marked with

labels containing “3” or “ALL”.

Example:

For Australia and N.Z.

• The region number of this unit is “4”.

• The unit will play DVD-Video marked with

labels containing “4” or “ALL”.

Example:

ALL

RQT8020

Getting started

ENGLISH

Caution for AC Mains Lead

(For Saudi Arabia)

For your safety, please read the following text carefully.

This appliance is supplied with a moulded three pin mains plug for

your safety and convenience.

A 5-ampere fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that the

replacement fuse has a rating of 5-ampere and that it is approved by

ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the

fuse.

If the plug contains a removable fuse cover you must ensure that it is

refitted when the fuse is replaced.

If you lose the fuse cover the plug must not be used until a

replacement cover is obtained.

A replacement fuse cover can be purchased from your local dealer.

If a new plug is to be fitted please observe the wiring code as stated

below.

If in any doubt please consult a qualified electrician.

IMPORTANT

The wires in this mains lead are coloured in accordance with the

following code:

Blue: Neutral, Brown: Live.

As these colours may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows:

The wire which is coloured Blue must be connected to the terminal

which is marked with the letter N or coloured Black or Blue.

The wire which is coloured Brown must be connected to the terminal

which is marked with the letter L or coloured Brown or Red.

WARNING: DO NOT CONNECT EITHER WIRE TO THE

EARTH TERMINAL WHICH IS MARKED WITH THE

LETTER E, BY THE EARTH SYMBOL

OR COLOURED

GREEN OR GREEN/YELLOW.

THIS PLUG IS NOT WATERPROOF—KEEP DRY.

Before use

Remove the connector cover.

How to replace the fuse

The location of the fuse differ according to the type of AC mains plug

(figures A and B). Confirm the AC mains plug fitted and follow the

instructions below.

Illustrations may differ from actual AC mains plug.

1. Open the fuse cover with a screwdriver.

2. Replace the fuse and close or attach the fuse cover.

CAUTION!

THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS OR ADJUSTMENTS OR

PERFORMANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.

REFER SERVICING TO QUALIFIED PERSONNEL.

WARNING:

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR

PRODUCT DAMAGE, DO NOT EXPOSE THIS APPARATUS TO

RAIN, MOISTURE, DRIPPING OR SPLASHING AND THAT NO

OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL

BE PLACED ON THE APPARATUS.

CAUTION!

• DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE,

BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE.

ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT

RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO

OVERHEATING, ENSURE THAT CURTAINS AND ANY

OTHER MATERIALS DO NOT OBSTRUCT THE

VENTILATION VENTS.

• DO NOT OBSTRUCT THE UNIT’S VENTILATION OPENINGS

WITH NEWSPAPERS, TABLECLOTHS, CURTAINS, AND

SIMILAR ITEMS.

• DO NOT PLACE SOURCES OF NAKED FLAMES, SUCH AS

LIGHTED CANDLES, ON THE UNIT.

• DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY

FRIENDLY MANNER.

THIS UNIT IS INTENDED FOR USE IN MODERATE CLIMATES.

THIS UNIT IS INTENDED FOR USE IN TROPICAL CLIMATES.

This product may receive radio interference caused by mobile

telephones during use. If such interference is apparent, please

increase separation between the product and the mobile

telephone.

The socket outlet shall be installed near the equipment and easily

accessible or the mains plug or an appliance coupler shall remain

readily operable.

For Continental Europe, Australia and N.Z.

For Asia and Middle East

(Inside of product)

(Tuotteen sisällä)

(Produktets innside)

RQLS0233

VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN.

AVOID DIRECT EXPOSURE TO BEAM.

DANGER

(FDA 21 CFR)

(IEC60825-1)

VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN.

AVOID EXPOSURE TO BEAM.

CAUTION

RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS D’OUVERTURE.

EXPOSITION DANGEREUSE AU FAISCEAU.

ATTENTION

SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING.

UNDGÅ UDSÆTTELSE FOR STRÅLING.

ADVARSEL

AVATTAESSA OLET ALTTIINA NÄKYVÄÄ JA NÄKYMÄTÖN

LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARO!

SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.

VARNING

SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES.

UNNGÅ EKSPONERING FOR STRÅLEN.

ADVARSEL

SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG

GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.

VORSICHT

CAUTION!

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE

SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD

BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF

SAFELY.

THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF

THE CUT OFF PLUG IS INSERTED INTO ANY 13-AMPERE

SOCKET.

Figure A Figure B

Fuse cover

Fuse

(5 ampere)

Fuse

(5 ampere)

RQT8020

Getting started

ENGLISH

Table of contents

Caution for AC Mains Lead . . . . . . . . . . . . . . . . . . . . . . . .2

Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

The remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Disc information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Control reference guide . . . . . . . . . . . . . . . . . . . . . . . . . . .6

STEP 1 Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

STEP 2 TV Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

STEP 3 Set up to match your television and

remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Recording television programmes . . . . . . . . . . . . . . . . .15

Recording modes and approximate recording times . . . . . . . 15

Recording television programmes . . . . . . . . . . . . . . . . . . . . . 15

Direct TV Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Playing while you are recording . . . . . . . . . . . . . . . . . . . . . . . 16

Flexible Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Recording from an external equipment . . . . . . . . . . . . . . . . . 17

Timer recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Using SHOWVIEW system to make timer recordings . . . . . . . . 18

Using G-

CODE system to make timer recordings. . . . . . . . . . . 19

Manually programming timer recordings . . . . . . . . . . . . . . . . 20

Recording from digital/satellite receiver or decoder . . . . . . . . 20

Check, change or delete a programme . . . . . . . . . . . . . . . . . 21

Making timer recordings on the television . . . . . . . . . . . . . . . 21

Linked timer recordings with external equipment

(digital/satellite receiver)–EXT LINK. . . . . . . . . . . . . . . . . . . . 21

Playing discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Changing audio during play . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Operations during play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Editing operations during play . . . . . . . . . . . . . . . . . . . . . . . . 23

Using menus to play MP3 and

still pictures (JPEG/TIFF) . . . . . . . . . . . . . . . . . . . . . . .24

Playing MP3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Playing still pictures (JPEG/TIFF). . . . . . . . . . . . . . . . . . . . . . 24

Using on-screen menus . . . . . . . . . . . . . . . . . . . . . . . . . .26

Common procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Disc menu–Setting the disc content . . . . . . . . . . . . . . . . . . . . 26

Play menu–Change the play sequence . . . . . . . . . . . . . . . . . 26

Picture menu–Change the picture quality. . . . . . . . . . . . . . . . 27

Sound menu–Change the sound effect. . . . . . . . . . . . . . . . . . 27

Other menu–Change the display position . . . . . . . . . . . . . . . . 27

FUNCTIONS window and Status messages . . . . . . . . . 27

FUNCTIONS window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Status messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Editing titles/chapters . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Editing titles/chapters and playing chapters . . . . . . . . . . . . . . 28

Title operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Chapter operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Creating, editing and playing playlists . . . . . . . . . . . . . 30

Creating playlists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Editing and playing playlists/chapters . . . . . . . . . . . . . . . . . . . 31

Playlist operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Chapter operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

DISC MANAGEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Setting the protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Providing a disc with a name. . . . . . . . . . . . . . . . . . . . . . . . . . 32

Erasing all titles–Erase all titles. . . . . . . . . . . . . . . . . . . . . . . . 32

Erasing all the contents of a disc–Format Disc . . . . . . . . . . . . 33

Enabling DVD-R, DVD-RW (DVD-Video format) or +R to be

played on other equipment–Finalize . . . . . . . . . . . . . . . . . . . . 33

Entering text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Changing the unit’s settings . . . . . . . . . . . . . . . . . . . . . 34

Common procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Summary of settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

TV System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Clock settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Child Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Frequently asked questions . . . . . . . . . . . . . . . . . . . . . 43

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Error messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover

Please check and identify the supplied accessories.

(Product numbers correct as of January 2005. These may be subject to change.)

■ Batteries

•

Insert so the poles (+ and –) match those in the remote control.

• Do not use rechargeable type batteries.

• Do not mix old and new batteries.

• Do not use different types at the same time.

• Do not heat or expose to flame.

• Do not take apart or short circuit.

• Do not attempt to recharge alkaline or manganese batteries.

• Do not use batteries if the covering has been peeled off.

Mishandling of batteries can cause electrolyte leakage which can

damage items the fluid contacts and may cause a fire.

Remove if the remote control is not going to be used for a long

period of time. Store in a cool, dark place.

Note

If you cannot operate the unit or television using the remote control

after changing the batteries, please re-enter the codes (➔ page 14).

■ Use

Getting started

Recording

Playing back

Editing

Convenient functions

Reference

Accessories

The remote control

1 Remote control

(EUR7720KL0)

(EUR7720KN0)

(EUR7720KP0)

For Continental Europe

For Australia, N.Z. and Asia

For Middle East

1 RF coaxial cable

2 Batteries

for remote control

1 Audio/video cable

• For use with this unit only.

Do not use it with other equipment.

Also do not use the cords for other equipment

with this unit.

For Australia

and N.Z.

For Middle East

For Continental

Europe and Asia

1 AC mains lead

For Saudi Arabia

2 AC mains lead

R6/LR6, AA

7 m directly in front of the unit

Remote control signal sensor

RQT8020

Getting started

ENGLISH

Disc information

Discs you can use for recording and play (12 cm/8 cm)

• We recommend using Panasonic discs. We recommend using DVD-RAM discs with cartridges to protect them from scratches and dirt.

• You may not be able to record to DVD-R, DVD-RW and +R discs on this unit or play them due to the condition of the recording.

• You cannot record programmes that allow “One time only recording” to CPRM compatible DVD-R and DVD-RW on this unit.

• You can use high speed recording compatible discs on this unit.

1 You cannot record or play continuously on two sides.

Play-only discs (12 cm/8 cm)

3 Play may be impossible on some CD-R, CD-RW, DVD-RW or +RW discs due to the condition of the recording.

4 You can play still pictures (JPEG/TIFF), CD-DA, Video CD and MP3 format data recorded on CD-R/RW.

• The producer of the disc can control how discs are played. So you may not always be able to control play as described in these operating

instructions. Read the disc’s instructions carefully.

Disc type DVD-RAM

• 4.7 GB/9.4 GB, 12 cm

• 2.8 GB, 8 cm

DVD-R (DVD-Video format)

• 4.7 GB, 12 cm

• 1.4 GB, 8 cm

Logo

Indication in these instructions

Before finalizing

After finalizing

Main use

Re-writable discs

One time recording discs

(recordable until the disc is full)

Maximum recording time

(➔ page 15, Recording modes and approximate recording times)

8 hours

(16 hours in EP ( 8Hours ) mode

on double-sided disc 1)

8 hours

Play on other players Only on DVD-RAM compatible

players. It is not necessary to

finalize the disc. (➔ page 41)

Only after finalizing the disc.

(➔ page 33)

What you can do on this unit ( : Can do × : Cannot do)

Chasing playback

Recording broadcasts that allow one copy

(CPRM (➔ page 41) compatible

discs only.)

Recording both M 1 and M 2 of bilingual broadcast

Only one is recorded

(➔ page 36, Bilingual Audio

Selection)

Recording 16:9 aspect picture

(The picture is recorded in 4:3

aspect.)

Enter programme (title) name

Erase programme (title)

(Available space increases

after erasing.)

(Available space does not

increase after erasing.)

Creating playlists

RAM

-R

DVD-V

Disc type DVD-Video DVD-Audio DVD-RW (DVD Video Recording

format)

+RW

Logo

––––

Indication in these

instructions

Instructions High quality movie and

music discs

High fidelity music discs

• Played on this unit in

2 channels.

DVD-RW recorded on another DVD

Recorder 3

• You can play programmes that

allow “One time only recording” if

they have been recorded to a

CPRM compatible disc.

• By formatting (➔ page 33) the

disc, you can record to it in

DVD-Video format and play it on

this unit.

+RW recorded on

another DVD

Recorder 3

• It may be necessary to finalize the disc on the

equipment used for recording.

Regarding DVD-Audio

Some multi-channel DVD-Audio will prevent down-mixing (➔ page 41) of all or part of their contents if this is the manufacturer’s intention. When

playing such discs, or such parts of disc, unless the number of connected speakers is the same as the disc’s channel specification, audio will not

be output properly (e.g. part of the audio is missing, multi-channel audio cannot be selected and audio is played in two channels.) Refer to the

disc’s jacket for more information.

DVD-V DVD-A

-RW(VR)

DVD-V

RQT8020

Getting started

ENGLISH

• 2.6 and 5.2 GB DVD-RAM, 12 cm

• 3.95 and 4.7 GB DVD-R for Authoring

• DVD-R recorded by DVD Video Recording format

• DVD-R (DVD-Video format), DVD-RW (DVD-Video format), +R

recorded on another unit and not finalized (➔ page 41).

• DVD-Video with a region

number other than “2” or “ALL”

DVD-Video with a region number other than “3” or “ALL”

DVD-Video with a region number other than

“4” or “ALL”

• Blu-ray

• DVD-ROM, DVD-R DL, +R DL, +R (8 cm), CD-ROM, CDV, CD-G,

Photo CD, CVD, SVCD, SACD, MV-Disc, PD, Divx Video Disc, etc.

■ How to hold a disc

Do not touch the recorded surface.

■ Concerning non-cartridge

discs

Be careful about scratches and dirt.

■ If there is dirt or

condensation on the disc

Wipe with a damp cloth and then wipe dry.

■ Handling precautions

•

Do not attach labels or stickers to

discs. (This may cause disc warping and un-balanced rotation,

rendering it unusable.)

• Write on the label side of the disc only with a soft, oil-based felt

pen. Do not use ballpoint pens or other hard writing implements.

• Do not use record cleaning sprays, benzine, thinner, static

electricity prevention liquids or any other solvent.

• Do not use scratch-proof protectors or covers.

• Do not drop, stack, or impact discs. Do not place objects on them.

• Do not use the following discs:

– Discs with exposed adhesive from removed stickers or labels

(rented discs etc).

– Discs that are badly warped or cracked.

– Irregularly shaped discs, such as

heart shapes.

• Do not place in the following areas:

– In direct sunlight.

– In very dusty or humid areas.

– Near a heater.

– Locations susceptible to significant differences in temperature

(condensation can occur).

– Where static electricity or electromagnetic waves occur.

• To protect discs from scratches and dirt, return them to their cases

or cartridges when you are not using them.

When you use the discs recorded either PAL or NTSC, refer to this table.

( : Possible to view, ×: Impossible to view)

If you select “NTSC” in “TV System” (➔ page 39), the picture may

be clearer.

Select “NTSC” in “TV System” (➔ page 39).

If your television is not equipped to handle PAL 525/60 signals

the picture will not be shown correctly.

DVD-RW (DVD-Video format)

• 4.7 GB, 12 cm

• 1.4 GB, 8 cm

• 4.7 GB, 12 cm

––––

Before finalizing Before finalizing

After finalizing After finalizing

Re-writable discs

One time recording discs

(recordable until the disc is full)

8 hours

Only after finalizing the disc.

(➔ page 33)

Only after finalizing the disc.

(➔ page 33)

××

Only one is recorded

(➔ page 36, Bilingual Audio

Selection)

Only one is recorded

(➔ page 36, Bilingual Audio

Selection)

(The picture is recorded in 4:3

aspect.)

(The picture is recorded in 4:3

aspect.)

(The available space on

DVD-RW (DVD-Video format)

increases only when the last

recorded title is erased.) 2

(Available space does not

increase after erasing.)

××

Audio CD Video CD

––––

Music and audio

recorded

(including

CD-R/RW 3 4)

CD-R and

CD-RW 3 4

with music

recorded in MP3

Still pictures

(JPEG and TIFF)

recorded on

CD-R and

CD-RW 3 4

Music and video recorded

(including CD-R/RW 3 4)

The manufacturer accepts no responsibility and offers no

compensation for loss of recorded or edited material due to a

problem with the unit or recordable media, and accepts no

responsibility and offers no compensation for any

subsequent damage caused by such loss.

Examples of causes of such losses are

• A disc recorded and edited with this unit is played in a DVD

recorder or computer disc drive manufactured by another

company.

• A disc used as described above and then played again in this

unit.

• A disc recorded and edited with a DVD recorder or computer disc

drive manufactured by another company is played in this unit.

-RW(V) +R

DVD-V DVD-V

The available space does not increase if these are erased.

Erase this to increase the available space.

Title 1 Title 2

The last

recorded title

The available

space

- - - -

CD VCD

DVD Video Recording format

This is a recording method which allows you to freely record and

edit television broadcasts and so on.

• Digital broadcasts that allow “One time only recording” can be

recorded to a CPRM compatible disc. You can record to CPRM

compatible DVD-RAM on this unit.

• Play is only possible on a compatible DVD player.

Use a DVD-RAM to record by the DVD Video Recording format.

DVD-Video format

This recording method is the same as commercially available DVD-Video.

• Digital broadcasts that allow “One time only recording” cannot be

recorded.

•

These can be played on a DVD player. However programmes recorded

on this unit must be finalized to be played on other DVD players.

Use a DVD-R or DVD-RW to record by the DVD-Video format.

Discs that cannot be played

Disc handling

Types of disc for the type of connected TV

TV type Disc Yes/No

Multi-system TV

PAL

NTSC

NTSC TV

PAL

NTSC

PAL TV

PAL

NTSC

(PAL60)

For Continental Europe and Middle East

For Asia

For Australia and N.Z.

RQT8020

Getting started

ENGLISH

Control reference guide

e.g.,

Remote control

Continental Europe

SKIP SLOW/SEARCH

REC MODE

REC

F Rec

TIME SLIP

FUNCTIONSDIRECT NAVIGATOR

TOP MENU

RETURN

VOLUME

STATUS

DISPLAY

SUB MENU

DIRECT TV REC

CANCEL

MANUAL SKIP

INPUT SELECT

AUDIO

ERASE

EXT LINK

CHAPTER

PROG/CHECK

TIMER

ShowView

CREATE

Turn the unit on (➔ page 10, 12)

Direct TV recording (➔ page 16)

Input select (AV1, AV2, AV3 or AV4)

For Continental Europe

For Australia, N.Z., Asia and Middle East

Select channels and title numbers etc./

Enter numbers

Cancel

Basic operations for recording and play

Show Top menu/Direct Navigator

(➔ page 22, 24, 28)

Show sub menu (➔ page 25, 28, 31)

Show on-screen menu (➔ page 26)

Change recording mode (➔ page 15)

Select Audio (➔ page 22)

Create chapter (➔ page 23)

For Continental Europe

(➔ page 14)Television operations

Channel select (➔ page 15)

Show S

HOWVIEW screen (➔ page 18)

Show G-

CODE screen (➔ page 19)

For Continental Europe

For Australia, N.Z. and Asia

Skip 30 seconds forward (➔ page 23)

Input select (AV1, AV2, AV3 or AV4)

Select channels

For Continental Europe

For Australia, N.Z., Asia and Middle East

Show FUNCTIONS window (➔ page 13, 27)

(➔ page 10, 12, 23)

Selection/Enter, Frame-by-frame

Return to previous screen

Show status messages (➔ page 27)

Skip the specified time/Display the television image

as a picture-in-picture (➔ page 16, 23)

Start Flexible Recording (➔ page 17)

Programme recording standby/release

(➔ page 18, 19, 20)

Linked timer recordings with external equipment

(➔ page 21)

Erase items (➔ page 23)

For Continental Europe

For Australia, N.Z., Asia and Middle East

Show timer recording programme screen

(➔ page 20)

(➔ page 38)Manual tuning operation

Erase items (➔ page 23)

Create chapter (➔ page 23)

For Continental Europe

For Australia, N.Z., Asia and Middle East

INPUT SELECT

G-Code

ERASE

CREATE

CHAPTER

Start recording (➔ page 15)

Main unit

Continental Europe

REC

OPEN/CLOSE

EXT LINK

Display (➔ below)

Disc tray (➔ page 15, 22)

Open/close disc tray (➔ page 15, 22)

Channel select (➔ page 15)

Start recording (➔ page 15)

Connection for camcorder etc.

(➔ page 17)

/Remote control signal sensor

Standby/on switch (8) (➔ page 10)

Press to switch the unit from on to

standby mode or vice versa.

In standby mode, the unit is still

consuming a small amount of power.

Start play (➔ page 22)

Stop (➔ page 16, 23)

Rear panel terminals (➔ page 7, 8)

Linked timer recordings

with external equipment

(➔ page 21)

For Continental Europe

Opening the front panel

Press down on the part

with your finger.

The unit’s display

Continental Europe

EXT Link D.MIX

–

RAM

PLAY

REC

PLAY PLAY

REC

AVCD

DVD

D. MIX (multi-channel DVD-Audio only)

When lit: down-mixing audio is played.

When off: the disc prevents down-mixing so only

the two front channels can be played.

Recording modeMain display section

Disc type

Recording

Playback

Recording/

Playback

Timer recording indicator

Linked timer recordings with external

equipment indicator

For Continental Europe

RQT8020

Getting started

ENGLISH

STEP 1 Connection

• The equipment connections described are examples.

• Before connection, turn off all equipment and read the appropriate operating instructions.

• Peripheral equipment and optional cables are sold separately unless otherwise indicated.

When there is no 21-pin Scart terminal on the television (➔ page 8)

■ RGB

This refers to the three primary colours of light, red (R), green (G), and blue (B) and also the method of producing video that uses them. By

dividing the video signal into the three colours for transmission, noise is reduced for even higher quality images.

■ Q Link functions

Q Link offers a range of convenient functions (For further details ➔ page 42). Make sure to connect a fully wired 21-pin Scart cable to the

television if using the Q Link function.

The following systems from other manufacturers have similar function to Q Link from Panasonic. For details, refer to your television’s operating

instructions or consult your dealer.

• Q Link (registered trademark of Panasonic)

• DATA LOGIC (registered trademark of Metz)

• Easy Link (registered trademark of Philips)

• Megalogic (registered trademark of Grundig)

• SMARTLINK (registered trademark of Sony)

■ Do not connect the unit through a video cassette recorder

Video signals fed through video cassette recorders will be affected by copyright

protection systems and the picture will not be shown correctly on the television.

• When connecting to a television with a built in VCR, connect to the input terminals on

the television side, not the VCR side.

■ When the unit is not to be used for a long time

To save power, unplug it from the household mains socket. This unit

consumes a small amount of power, even when it is turned off

[approx. 3 W (Power Save mode)].

Connecting a television with 21-pin Scart terminal and VCR

VHF/UHF

RF IN

AV IN

VHF/UHF

RF IN

AV OUT

Television’s rear panel

This unit’s

rear panel

indicates included accessories.

indicates accessories not included.

are required connections. Connect in the numbered order.

VCR’s rear panel

AV1 terminal

If your television is equipped with RGB input

capability, by connecting with a fully wired 21-pin

Scart cable you can see video using RGB output on

this unit (➔ below).

To output in RGB select “RGB (without component)”

from “AV1 Output” in the SETUP menu (➔ page 36)

after tuning is completed (➔ page 10–12).

Fully wired 21-pin

Scart cable

RF coaxial

cable

To the aerial

Aerial

cable

Use a splitter if you also

want to connect the

aerial to your VCR.

Splitter

21-pin Scart cable

To household mains socket

(AC 220-240 V, 50 Hz)

(AC 220-240 V, 50 Hz/60 Hz)

For Continental Europe,

Australia and N.Z.

For Asia and Middle East

e.g.,

Continental Europe

BE SURE TO READ THE CAUTION

FOR THE AC MAINS LEAD ON PAGE 2

BEFORE CONNECTION.

AC mains lead

Connect only after all other

connections are complete.

• Use the AC mains lead

that matches the socket

for the area you live in.

For Middle East

For Saudi Arabia

For Continental Europe

Television

This unit

VCR

Television

VCR

This unit

Before moving the unit, ensure the disc tray is

empty.

Failure to do so will risk severely damaging the disc and

the unit.

RQT8020

Getting started

ENGLISH

STEP 1 Connection

Connecting to the television using the 21-pin Scart cables (➔ page 7)

(➔ page 9, Note to owners of progressive compatible PAL

system televisions)

■ Component video output

Component signal outputs the colour difference signals (PB/PR) and luminance signal (Y) separately in order to achieve high fidelity in

reproducing colours. If the television is compatible with progressive output, a high quality picture can be output because this unit’s component

video output terminal outputs a progressive output signal (➔ page 42).

Connecting a television with AUDIO/VIDEO terminals and VCR

Connecting a television with S VIDEO or COMPONENT VIDEO terminals

VHF/UHF

RF IN

VHF/UHF

RF IN

R L

AUDIO OUT VIDEO OUT

AUDIO IN

R L

VIDEO IN

Audio/Video cable

This unit’s

rear panel

BE SURE TO READ THE CAUTION

FOR THE AC MAINS LEAD ON PAGE 2

BEFORE CONNECTION.

indicates included accessories.

indicates accessories not included.

are required connections. Connect in the numbered order.

To the aerial

Splitter

Aerial

cable

Television’s rear panel

Red White Yellow

RF coaxial cable

AC mains lead

Connect only after all other

connections are complete.

• Use the AC mains lead

that matches the socket

for the area you live in.

For Middle East

Audio/Video cable

VCR’s rear panel

Red

White

Yellow

Red

White

Yellow

Red White Yellow

Use a splitter if you also

want to connect the

aerial to your VCR.

For Saudi Arabia

To household mains socket

(AC 220-240 V, 50 Hz)

(AC 220-240 V, 50 Hz/60 Hz)

For Continental Europe,

Australia and N.Z.

For Asia and Middle East

e.g.,

Asia

AUDIO IN

R L

VIDEO

COMPONENT

VIDEO IN

S VIDEO

Television’s

rear panel

Red White Yellow

Audio/Video

cable

S Video cable

This unit’s

rear panel

S VIDEO OUT terminal

Connect to S VIDEO IN terminal on the television through

a S Video cable.

The S VIDEO OUT terminal achieves a more vivid picture than

the VIDEO OUT terminal. (Actual results depend on the

television.)

Red

White

Yellow

e.g.,

Continental Europe

AUDIO IN

R L

VIDEO

COMPONENT

VIDEO IN

S VIDEO

Television’s

rear panel

Red White Yellow

Audio/Video

cable

Video cable

This unit’s

rear panel

COMPONENT VIDEO OUT terminal

Connect to COMPONENT VIDEO IN terminals on the television

through a component video cable. These terminals can be used

for either interlace or progressive output (➔ page 42) and provide

a purer picture than the S VIDEO OUT terminal.

• Connect to terminals of the same colour.

• Video output from the component terminal will have no colour

during EXT LINK recordings. Use a fully wired 21-pin Scart

cable between the TV and the unit when viewing external

equipment picture through the AV2 terminal.

For Continental Europe

Red

White

Yellow

e.g.,

Continental Europe

RQT8020

Getting started

ENGLISH

• Decoder here means the device used to decode scrambled broadcasts (Pay TV).

• Change the “AV2 Input” and “AV2 Connection” settings in the SETUP menu to match the connected equipment (➔ page 36).

■ To enjoy multi-channel surround sound on

DVD-Video

Connect an amplifier with Dolby Digital, DTS and MPEG decoders

using an optical digital audio cable and change the settings in

“Digital Audio Output” (➔ page 36).

• You cannot use DTS Digital Surround decoders not suited to DVD.

• Even if using this connection, output will be only 2 channels when

playing DVD-Audio.

■ Connection to a stereo amplifier

For Continental Europe

Connecting a digital/satellite receiver or decoder

Connecting an amplifier or system component

AV OUT

This unit’s rear panel

21-pin Scart cable

Digital/satellite receiver or

decoder’s rear panel

Viewing video from the decoder on the television while

the unit is stopped, or while recording

If you connected the television to the AV1 terminal and the

decoder to the AV2 terminal on this unit, press

[0]+[ENTER]. (“DVD” appears on the unit’s display.)

Press again to cancel. (“TV” appears on the unit’s display.)

• If the television is compatible with RGB input, the RGB

output signal from the decoder can also be output from

the main unit the same way.

OPTICAL IN

Optical digital audio cable

Do not bend this cable sharply.

Insert fully, with this side facing up.

This unit’s rear panel

Amplifier’s rear panel

e.g.,

Continental Europe

AUDIO IN

R L

Amplifier’s rear panel

This unit’s rear panel

Audio cable

Red White

White

Red

e.g.,

Continental Europe

Do not place the unit on

amplifiers or equipment

that may become hot.

The heat can damage the unit.

Note to owners of progressive compatible PAL system televisions

•

If you have an LCD/plasma television or LCD projector

Using progressive output, you can enjoy high-resolution video

recorded on media such as DVD-Video. Connect this unit’s

component video output terminals to your television and turn on the

progressive output setting (➔ page 13).

• If you have a CRT (cathode ray tube) television

Use component output with progressive “Off” (Factory setting,

➔ page 36), even if it is progressive compatible, because

progressive output can cause some flickering. This is the same for

multi system televisions using PAL mode.

COMPONENT

VIDEO OUT

COMPONENT

VIDEO IN

This unit

Progressive output

COMPONENT

VIDEO OUT

COMPONENT

VIDEO IN

This unit

Progressive output

RQT8020

Getting started

ENGLISH

STEP 2 TV Tuning

When connecting to a television that has the Q Link

function (➔ page 42) with a fully wired 21-pin Scart

cable (➔ page 7).

(The AV2 and AV4 Scart terminals on Panasonic televisions are

compatible with the Q Link function.)

You can download the tuning positions from the television.

This unit Auto Clock Setting function synchronizes the time when

the TV channel that is broadcasting time and date information is

tuned.

1 Turn on the television and select the

appropriate AV input to suit the

connections to this unit.

2 Press [^ DVD] to turn the unit on.

Tuning Preset Downloading starts.

Tuning Preset Downloading is complete when you see the

television picture.

• If the Country setting menu appears on the television, press

[e, r, w, q] to select the country and press [ENTER].

If you select “Schweiz”, “Suisse” or “Svizzera” in the Country

setting, or when the television tuning setting has been set to

Switzerland, the “Power Save” setting menu appears. Select

“On” or “Off” (➔ page 37).

To stop partway

Press [RETURN].

■ If the clock setting menu appears

Set the clock manually (➔ page 40).

■ To confirm that stations have been tuned

correctly (➔ page 38)

■ To restart Preset Download (➔ page 39)

SKIP SLOW/SEARCH

REC MODE

REC

F Rec

TIME SLIP

FUNCTIONSDIRECT NAVIGATOR

TOP MENU

RETURN

VOLUME

STATUS

DISPLAY

SUB MENU

DIRECT TV REC

CANCEL

INPUT SELECT

AUDIO

ERASE

EXT LINK

CREATE

CHAPTER

PROG/CHECK

TIMER

MANUAL SKIP

ShowView

^ DVD

RETURN

e, r, w, q

ENTER

2 CH 1

REC

OPEN/CLOSE

EXT LINK

e.g.,

Continental Europe

e.g.,

Continental Europe

Numbered

buttons

Tuning Preset Download

(Setup with Q Link functions)

For Continental Europe

Download from TV

Pos 2

Download in progress, please wait.

RETURN: to abort

RETURN

Country

RETURN: leave ENTER: access

Others

Deutschland

Österreich

Portugal

Suomi

Sverige

Schweiz

Suisse

Svizzera

België

Belgique

Belgien

Danmark

España

France

Italia

Nederland

Norge

RETURN

SELECT

ENTER

RQT8020

Getting started

ENGLISH

• When connecting to a television with the VIDEO OUT,

S VIDEO OUT or COMPONENT VIDEO OUT terminal (

➔

page 8).

• When connecting to a television that does not have the

Q Link function (➔ page 42).

This unit’s Auto-Setup function automatically tunes all available TV

stations and synchronizes the time when the TV channel that is

broadcasting time and date information is tuned.

1 Turn on the television and select the

appropriate AV input to suit the

connections to this unit.

2 Press [^ DVD] to turn the unit on.

The Country setting menu appears.

If you select “Schweiz”, “Suisse” or “Svizzera”, the “Power

Save” setting menu appears. Select “On” or “Off”

(➔ page 37).

3 Press [e, r, w, q] to select the

country.

4 Press [ENTER].

Auto-Setup starts. This takes about 8 minutes.

Auto-Setup is complete when you see the television picture.

To stop partway

Press [RETURN].

■ If the clock setting menu appears

Set the clock manually (➔ page 40).

■ To confirm that stations have been tuned

correctly (➔ page 38)

■ To restart Auto-Setup (➔ page 39)

You can also use the following method to restart Auto-Setup.

When the unit is on and stopped

Press and hold [2 CH] and [CH 1] on the main unit until the

Country setting screen appears.

• All the settings except for the ratings level, ratings password and

time settings return to the factory preset. The timer recording

programmes are also cancelled.

Auto-Setup

(Setup without Q Link functions)

For Continental Europe

Country

RETURN: leave ENTER: access

Others

Deutschland

Österreich

Portugal

Suomi

Sverige

Schweiz

Suisse

Svizzera

België

Belgique

Belgien

Danmark

España

France

Italia

Nederland

Norge

RETURN

SELECT

ENTER

Auto-Setup

Ch 1

Auto-Setup in progress, please wait.

RETURN: to abort

RETURN

RQT8020

Getting started

ENGLISH

Refer to the control reference on page 10.

STEP 2 TV Tuning

When connecting to a television with the corresponding

terminal (➔ page 8).

This unit’s Auto-Setup function automatically tunes all available TV

stations.

1 Turn on the television and select the

appropriate AV input to suit the

connections to this unit.

2 Press [^ DVD] to turn the unit on.

The Country setting menu appears on the television.

3 Press [e, r] to select the country and

press [ENTER].

Auto-Setup starts. This takes about 5 minutes.

Auto-Setup is complete when you see the clock setting

menu.

4 Press [w, q] to select the item you

want to change.

This is a 24-hour clock.

The items change as follows:

Reset the clock regularly to maintain accuracy (➔ page 40).

(Monthly accuracy +/– 15 seconds.)

5 Press [e, r] to change the setting.

You can also use the numbered buttons for setting.

6 Press [ENTER] when you have

finished the settings.

The clock starts and the television displays the channel being

received.

To stop partway

Press [RETURN].

■ To confirm that stations have been tuned

correctly (➔ page 38)

■ To restart Auto-Setup (➔ page 39)

You can also use the following method to restart Auto-Setup.

When the unit is on and stopped

Press and hold [2 CH] and [CH 1] on the main unit until the

Country setting screen appears.

• All the settings except for the ratings level, ratings password and

time settings return to the factory preset. The timer recording

programmes are also cancelled.

When connecting to a television with the corresponding

terminal (➔ page 8).

This unit’s Auto-Setup function automatically tunes all available TV

stations.

1 Turn on the television and select the

appropriate AV input to suit the

connections to this unit.

2 Press [^ DVD] to turn the unit on.

Auto-Setup starts. This takes about 5 minutes.

Auto-Setup is complete when you see the clock setting

menu.

3 Press [w, q] to select the item you

want to change.

This is a 24-hour clock.

The items change as follows:

Reset the clock regularly to maintain accuracy (➔ page 40).

(Monthly accuracy +/– 15 seconds.)

4 Press [e, r] to change the setting.

You can also use the numbered buttons for setting.

5 Press [ENTER] when you have

finished the settings.

The clock starts and the television displays the channel being

received.

To stop partway

Press [RETURN].

■ To confirm that stations have been tuned

correctly (➔ page 38)

■ To restart Auto-Setup (➔ page 39)

You can also use the following method to restart Auto-Setup.

When the unit is on and stopped

Press and hold [2 CH] and [CH 1] on the main unit until the

Auto-Setup screen appears.

• All the settings except for the ratings level, ratings password and

time settings return to the factory preset. The timer recording

programmes are also cancelled.

Auto-Setup

For Australia and N.Z.

Country

Australia

Others

New Zealand

Auto-Setup

128

Auto-Setup in progress, please wait.

RETURN: to abort

RETURN

Clock

Time Date

00 :

Please set clock manually.

ENTER: store RETURN: leave

0 9

No.

CHANGE

SELECT

ENTER

1 1..

2005

Hour Minute Second Day Month Year

Auto-Setup

For Asia and Middle East

Auto-Setup

128

Auto-Setup in progress, please wait.

RETURN: to abort

RETURN

Clock

Time Date

00 :

1 1..

2005

Please set clock manually.

ENTER: store RETURN: leave

0 9

No.

CHANGE

SELECT

ENTER

Hour Minute Second Day Month Year

RQT8020

Getting started

ENGLISH

STEP 3 Set up to match your television and remote control

Choose the setting to suit your television and preference.

1 While stopped

Press [FUNCTIONS].

2 Press [e, r] to select “To Others”

and press [ENTER].

3 Press [e, r] to select “SETUP” and

press [ENTER].

e.g.,

4 Press [e, r] to select “Connection”

and press [q].

5 Press [e, r] to select “TV Aspect”

and press [ENTER].

6 Press [e, r] to select the TV aspect

and press [ENTER].

You can enjoy progressive video by connecting this unit’s

COMPONENT VIDEO OUT terminals to an LCD/plasma television

or LCD projector compatible with progressive scan (➔ page 42).

1 While stopped

Press [FUNCTIONS].

2 Press [e, r] to select “To Others”

and press [ENTER].

3 Press [e, r] to select “SETUP” and

press [ENTER].

4 Press [e, r] to select “Connection”

and press [q].

5 Press [e, r] to select “Progressive”

and press [ENTER].

6 Press [e, r] to select “On” and press

[ENTER].

Output becomes progressive.

Note

• When connected to a CRT (Cathode ray tube) television, even if it

is progressive compatible, progressive output can cause some

flickering. Turn off “Progressive” if this occurs (➔ page 27).

• Picture will not be displayed correctly if connected to an

incompatible television.

• There is no output from the COMPONENT VIDEO OUT terminals

if “AV1 Output” in the SETUP menu is set to “RGB (without

component)”. Set this item to either “Video (with component)” or

“S Video (with component)” (➔ page 36).

• If the unit is connected to the television through VIDEO OUT,

S VIDEO OUT or AV1 terminal, output will be interlace

irrespective of the settings.

To exit the screen

Press [RETURN] several times.

To return to the previous screen

Press [RETURN].

Selecting television type and aspect

SKIP SLOW/SEARCH

TIME SLIP

FUNCTIONSDIRECT NAVIGATOR

TOP MENU

RETURN

VOLUME

STATUS

DISPLAY

SUB MENU

DIRECT TV REC

CANCEL

MANUAL SKIP

INPUT SELECT

PROG/CHECK

ShowView

Numbered

buttons

RETURN

e, r, w, q

ENTER

TV operation

buttons

FUNCTIONS

e.g.,

Continental Europe

FUNCTIONS No Disc

DVD

Playback

ENTER

RETURN

To Others Return

Recording

TIMER RECORDING

ShowView

SETUP

e.g.,

Continental Europe

SETUP

Disc

Picture

Sound

Display

Connection

Others

Tuning

Manual

Auto-Setup Restart

Download from TV

TAB

SELECT

RETURN

To enjoy progressive video

SETUP

Disc

Picture

Sound

Display

Tuning

TV Aspect

16:9

4:3

Letterbox

Others

16:9 WIDE TV

4:3 TV

Connection

SELECT

ENTER

RETURN

• 16:9: 16:9 widescreen television

• 4:3: 4:3 standard aspect television

Even if it records and plays, the aspect does not

change.

Video recorded for a widescreen is played as Pan &

Scan (unless prohibited by the producer of the

disc) (➔ page 42).

• Letterbox: 4:3 standard aspect television

Widescreen picture is shown in the letterbox style

(➔ page 42).

RAM

DVD-V

RQT8020

Getting started

ENGLISH

Refer to the control reference on page 13.

You can configure the remote control TV operation buttons to turn

the television on/off, change the television input mode, select the

television channel and change the television volume.

Point the remote control at the television

While pressing [^ TV], enter the code with

the numbered buttons.

e.g., 01: [0] ➔ [1]

Manufacturer and Code No.

Test by turning on the television and changing channels. Repeat the

procedure until you find the code that allows correct operation.

• If your television brand is not listed or if the code listed for your

television does not allow control of your television, this remote

control is not compatible with your television.

If other Panasonic products are placed close together, change the

remote control code on the main unit and the remote control (the

two must match).

Under normal circumstances use the factory set code “DVD 1”.

1 While stopped

Press [FUNCTIONS].

2 Press [e, r] to select “To Others”

and press [ENTER].

3 Press [e, r] to select “SETUP” and

press [ENTER].

4 Press [e, r] to select “Others” and

press [q].

5 Press [e, r] to select “Remote

Control” and press [ENTER].

6 Press [e, r] to select the code

(“DVD 1”, “DVD 2” or “DVD 3”) and

press [ENTER].

To change the code on the remote control

7 While pressing [ENTER], press and

hold the numbered button ([1], [2] or

[3]) for more than 2 seconds.

8 Press [ENTER].

■ When the following indicator appears on the

unit’s display

Note

Executing “Shipping Condition” in the SETUP menu returns the

main unit code to “DVD 1”. Change the remote control code to 1

(➔ step 7).

Television operation

Brand Code Brand Code

Panasonic

01, 02, 03,

04, 45

NOKIA 25, 26, 27

AIWA 35 NORDMENDE 10

AKAI 27, 30 ORION 37

BLAUPUNKT 09 PHILIPS 05, 06

BRANDT 10, 15 PHONOLA 31, 33

BUSH 05, 06 PIONEER 38

CURTIS 31 PYE 05, 06

DESMET 05, 31, 33 RADIOLA 05, 06

DUAL 05, 06 SABA 10

ELEMIS 31 SALORA 26

FERGUSON 10 SAMSUNG 31, 32, 43

GOLDSTAR/LG 31 SANSUI 05, 31, 33

GOODMANS 05, 06, 31 SANYO 21

GRUNDIG 09 SBR 06

HITACHI

22, 23, 31,

40, 41, 42

SCHNEIDER

05, 06, 29,

30, 31

INNO HIT 34 SELECO 06, 25

IRRADIO 30 SHARP 18

ITT 25 SIEMENS 09

JVC 17, 39 SINUDYNE 05, 06, 33

LOEWE 07 SONY 08

METZ 28, 31 TELEFUNKEN

10, 11, 12,

13, 14

MITSUBISHI 06, 19, 20 THOMSON 10, 15, 44

MIVAR 24 TOSHIBA 16

NEC 36

WHITE

WESTINGHOUSE

05, 06

Brand Code Brand Code

Panasonic/

National

01, 02, 03,

PHILIPS 12

GOLDSTAR/LG 15, 16 SAMSUNG 12, 17, 18

HITACHI 08 SANYO 14, 19

JVC 07 SHARP 11

MITSUBISHI 09, 10 SONY 05

NEC 13 TOSHIBA 06

For Continental Europe

For Australia, N.Z., Asia and Middle East

When other Panasonic products

respond to this remote control

SETUP

Remote Control

Picture

Tuning

Disc

Press “ ” and “ENTER” together

for more than 2 seconds on the remote

control.

Press and hold [ENTER] and

the indicated number button at

the same time for more than 2

seconds.

RQT8020

RecordingRecording

ENGLISH

Recording television programmes

Depending on the content being recorded, the recording times may

become shorter than indicated.

(Unit: hour)

When “Recording time in EP Mode” is set to “EP ( 6Hours )” in the

SETUP menu.

The sound quality is better when using “EP ( 6Hours )” than when

using “EP ( 8Hours )”.

Note

When recording to DVD-RAM using EP ( 8Hours ) mode, play may

not be possible on DVD players that are compatible with DVD-RAM.

In this case use EP ( 6Hours ) mode.

FR (Flexible Recording) Mode

The unit automatically selects a recording rate between XP and EP

( 8Hours ) that will enable the recordings to fit in the remaining disc

space with the best possible recording quality.

• You can set when programming timer recordings.

• All the recording modes from “XP” to “EP” appear in the display.

• It is not possible to record continuously from one side of a double

sided disc to the other. You will need to eject the disc and turn it

over.

• When using 8 cm DVD-RAM or 8 cm DVD-R, remove the disc from

the cartridge.

• You can record up to 99 titles on one disc ( 49 titles).

• It is not possible to record digital broadcasts that allow “One time

only recording” onto DVD-R, DVD-RW, +R or 8 cm DVD-RAM

discs. Use a CPRM compatible DVD-RAM.

Preparation

• Turn on the television and select the appropriate video input to suit

the connections to this unit.

• Turn the unit on.

1 Press [; OPEN/CLOSE] on the main

unit to open the tray and insert a disc.

• Press the button again to close the tray.

2 Press [1 2 CH] to select the channel.

3 Press [REC MODE] to select the

recording mode (XP, SP, LP or EP).

4 Press [* REC] to start recording.

The elapsed time is shown on the display.

Recording will take place on open space on disc. Data will not

be overwritten.

• You cannot change the channel or recording mode during

recording. You can change the channel or recording mode

while paused; however, the recording will then be as a

separate title.

• You can change the audio being received by pressing

[AUDIO] during recording. (This does not affect the actual

recording of the audio.)

Recording modes and approximate

recording times

Mode

DVD-RAM DVD-R

DVD-RW

(4.7 GB)

Single-sided

(4.7 GB)

Double-sided

(9.4 GB)

XP (High quality) 1 2 1

SP (Normal) 2 4 2

LP (Long play) 4 8 4

EP (Extra long play)

8 (6 ) 16 (12 ) 8 (6 )

FR (Automatic

mode selection)

8 hours

maximum

8 hours

maximum for

one side

8 hours

maximum

REC

OPEN/CLOSE

EXT LINK

SKIP SLOW/SEARCH

REC MODE

REC

F Rec

TIME SLIP

FUNCTIONSDIRECT NAVIGATOR

TOP MENU

RETURN

VOLUME

STATUS

DISPLAY

SUB MENU

DIRECT TV REC

CANCEL

MANUAL SKIP

INPUT SELECT

AUDIO

ERASE

EXT LINK

CREATE

CHAPTER

PROG/CHECK

TIMER

ShowView

Numbered

buttons

AV3 input terminals

F Rec

RETURN

e, r, w, q

ENTER

STATUS

TIME SLIP

DIRECT

NAVIGATOR

* DIRECT TV REC

INPUT SELECT

For Continental

Europe

For Australia, N.Z.,

Asia and Middle East

INPUT SELECT

-/--

For Continental

Europe

For Australia, N.Z.,

Asia and Middle East

z TIMER

e.g.,

Continental Europe

e.g.,

Continental Europe

AUDIO

EP ( 6Hours )

EP ( 8Hours )

Picture quality

Recording time

Recording television programmes

RAM

-R -RW(V) +R

When recording to DVD-R, DVD-RW (DVD-Video format) or +R

• When recording bilingual TV broadcast onto DVD-R, DVD-RW or

+R, only one of either “M 1” or “M 2” audio can be recorded.

Select at “Bilingual Audio Selection” (➔ page 36).

• The aspect ratio of the recorded images will be 4:3.

• In order to play a DVD-R, DVD-RW (DVD-Video format) or +R

recorded using this unit on another playback source, the

disc must first be finalized (➔ page 33).

Insert label-up.

Insert with the

arrow facing in.

Insert fully so it clicks

into place.

RAM

DVD

To select with the numbered buttons:

e.g.,

5: [0] ➔ [5] 5: [5]

15: [1] ➔ [5] 15: [-/--] ➔ [1] ➔ [5]

For Continental Europe For Australia, N.Z., Asia and Middle East

RAM

DVD

Remaining time on the disc

RAM

DVD

REC

RAM

RQT8020

Recording

ENGLISH

Recording television programmes

Refer to the control reference on page 15.

■ To stop recording

Press [g].

From the start to the end of the recording is called one title.

It takes about 30 seconds for the unit to complete recording

management information after recording finishes.

■ To pause recording

Press [h].

Press again to restart recording.

You can also press [* REC] to restart.

(Recorded title is not split into separate titles.)

The Quick Start feature enables this unit to start recording to a DVD-

RAM that is already inserted soon after turning it on.

It is set to “On” at the time of purchase (➔ page 37).

Note

Startup takes more time when:

– You play a disc or start recording to discs other than DVD-RAM.

– The clock has not been set.

During recording

Press [* REC] on the main unit to select the recording time.

Each time you press the button:

• This does not work during timer recordings (➔ page 18) or while

using Flexible Recording (➔ page 17).

The unit automatically records the programme’s and station’s name

if the station’s Title Page is correctly set (➔ page 38).

Note

The unit may take some time in retrieving titles (up to 30 minutes)

and may fail in some cases.

When you insert a new DVD-RW or a DVD-RAM or DVD-RW (DVD-

Video format) recorded on a computer or other equipment, a format

confirmation screen is displayed. Format the disc to use it. However

all the recorded contents are erased.

Press [w] to select “Yes” and press [ENTER].

■ To format a disc

(Several steps are necessary to format a disc.)

“Erasing all the contents of a disc–Format Disc” (➔ page 33)

When connected to a television that has the Q Link function

using a fully wired 21-pin Scart cable

(

➔

page 7)

This function allows you to immediately start recording the

programme that you are viewing on the TV.

Insert a disc. (➔ page 15)

Press and hold [* DIRECT TV REC]

for 1 second.

Recording starts.

To stop recording

Press [g].

Press [q] (PLAY) during recording.

Press [DIRECT NAVIGATOR] during

recording.

Press [e, r, w, q] to select a title and

press [ENTER].

To exit the Direct Navigator screen

Press [DIRECT NAVIGATOR].

Press [TIME SLIP] during recording.

• You will hear the playback audio.

Press [e, r] to select the time and

press [ENTER].

• Press [TIME SLIP] to show the play images in full. Press

again to show the play and recording images.

■ To stop play

Press [g].

■ To stop recording

2 seconds after play stops

Press [g].

■ To stop timer recording

Press [z TIMER].

• You can also press and hold [g] on the main unit for more than 3

seconds to stop recording.

Quick Start

To specify a time to stop recording—One Touch

Recording

If a station also broadcasts Teletext information

When the format confirmation screen is displayed

-R -RW(V) +R

30 (min.) 60 (min.) 90 (min.) 120 (min.)

240 (min.) 180 (min.)

Counter (cancel)

For Continental Europe

Format the disc in DISC MANAGEMENT ?

This disc is not formatted properly.

ENTER

SELECT

RETURN

Format

Yes

Direct TV Recording

Playing while you are recording

Playing from the beginning of the title you are

recording—Chasing playback

Playing a title previously recorded while recording—

Simultaneous rec and play

Reviewing the recorded images while recording—

Time Slip

For Continental Europe

RAM

0 min

PLAY

REC

Play starts from 30

seconds previous.

The current recording

images

RQT8020

Recording

ENGLISH

The unit sets the best possible picture quality that fits the recording

within the remaining disc space.

Preparation

• Select the channel to record or the external input.

While stopped

Press [F Rec].

Press [w, q] to select “Hour” and

“Min.” and press [e, r] to set the

recording time.

• You can also set the recording time with the numbered

buttons.

When you want to start recording

Press [e, r, w, q] to select “Start”

and press [ENTER].

Recording starts.

• All the recording modes from

XP to EP appear in the

display.

To exit the screen without recording

Press [RETURN].

To stop recording partway

Press [g].

To show the recording time

Press [STATUS].

Note

When performing EXT LINK recording (➔ page 21), the flexible

recording function does not work.

Preparation

• Connect a video cassette recorder, etc. to this unit’s input

terminals.

• When recording bilingual programmes

When both M 1 and M 2 is selected on the connected

equipment, you can select the audio type in playback.

Select either M 1 or M 2 on the connected

equipment. (The selected audio only is

recorded.)

• When the output signal from the external equipment is NTSC,

change the “TV System” to “NTSC” in the SETUP menu

(➔ page 39).

• To reduce noise in input from external equipment (e.g., video

casette recorder), set “AV-in NR” to “On” (➔ page 27).

• Check the time on the unit is correct.

e.g.,Connecting other video equipment to the AV3 input

terminals

If the audio output of the other equipment is monaural, connect to

L/MONO.

The S VIDEO terminal achieves a more vivid picture than the

VIDEO terminal.

While stopped

Press [INPUT SELECT] to select the

input channel for the equipment you

have connected.

Press [REC MODE] to select the

recording mode.

Start play on the other equipment.

Press [* REC].

Recording starts.

To skip unwanted parts

Press [h] to pause recording. (Press again to restart recording.)

To stop recording

Press [g].

To record programmes to fill up the remaining space on the

disc

➔ Left, Flexible Recording

Flexible Recording

Using “Flexible Recording” is convenient in these kind of

situations

• When the amount of free space on the disc makes selecting an

appropriate recording mode difficult

• When you want to record a long programme with the best picture

quality possible

e.g., Recording a 90 minutes programme to disc

: necessary space for recording

RAM

-R -RW(V) +R

FLEXIBLE REC

Star

Cancel

Recording in FR mode.

Set rec. time

8 Hour 00 Min.Maximum rec. time

1 Hour 30 Min.

Maximum recording

time

This is the maximum

recording time in EP

mode.

RAM

DVD

–

DVD-RAM

REC 59

L R

ARD

Recording

time

e.g., DVD-RAM

For Continental Europe

XP mode

If you select XP mode, the programme will not fit one disc.

SP mode

If you select SP mode, the programme will fit one disc.

FLEXIBLE REC

If you select “FLEXIBLE REC”, the programme will fit one disc

perfectly.

4.7GB

DVD-RAM

4.7GB

DVD-RAM

If you try to record a 90 minutes

programme in XP mode, only

the first 60 minutes will fit on the

disc and the 30 minutes

balance will not get recorded.

another disc is necessary

Full

4.7GB

DVD-RAM

However there will be 30 minutes

remaining disc space.

Remains

4.7GB

DVD-RAM

Fit

Recording from an external equipment

Almost all videos and DVD software on sale have been treated

to prevent illegal copying. Any software that has been so

treated cannot be recorded using this unit.

RAM

-R -RW(V) +R

RAM

-R -RW(V) +R

REC

OPEN/CLOSE

EXT LINK

Ye l l o w W h i t e R e d

S Video

cable

Audio/Video cable

Panasonic Diga DMR-ES10 Istruzioni per l'uso

Marca: Panasonic

Modello: Diga DMR-ES10

Categoria: Lettori DVD

Tipo: Istruzioni per l'uso

Questo manuale è adatto anche per

DMRES10

Scarica il pdf

rapporto

in altre lingue

English: Panasonic Diga DMR-ES10 Operating instructions

Panasonic Diga DMR-ES10 Istruzioni per l'uso

Questo manuale è adatto anche per

Panasonic Diga DMR-ES10 Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti