Mach P4MST-890 Setup Manual

P4MST-890 Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protec tion against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. There is no guarantee

that interfere nce will not occur in a particular ins talla tion.

The ve ndor makes no representa tions or warra nties with respec t to the

contents here and specially disclaims any implied warranties of merchantability

o r fi tnes s fo r a ny purpose . F urthe r t he ve ndo r res e rves t he rig ht to rev is e t his

publication and to make changes to the contents here without obligation to

notify any party beforehand.

D uplication of this publication, in pa rt or in whole, is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and

we will not be res ponsible for any mis takes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction .............................................3

1.1 Before You Start...................................................................3

1.2 Package Checklist................................................................3

1.3 Motherboard Features..........................................................4

1.4 Rear Panel Connectors..........................................................5

1.5 Motherboard Layout............................................................6

Chapter 2: Hardware Installation..............................7

2.1 Installing Central Processing Unit (CPU)................................7

2.2 FAN Headers........................................................................ 9

2.3 Installing System Memory.....................................................10

2.4 Connectors and Slots............................................................11

Chapter 3: Headers & Jumpers Setup......................13

3.1 How to Setup Jumpers..........................................................13

3.2 Detail Settings.....................................................................13

Chapter 4: Useful Help ..............................................18

4.1 Driver Installation Note .......................................................18

4.2 AWARD BIOS Beep Code......................................................19

4.3 Extra Information................................................................19

4.4 Troubleshooting...................................................................21

Chapter 5: WarpSpeeder™ .......................................22

5.1 Introduction........................................................................22

5.2 System Requirement............................................................22

5.3 Installation.........................................................................23

5.4 WarpSpeeder™....................................................................24

Appendencies: SPEC In Other Language ................30

German................................................................................................30

France..................................................................................................32

Italian..................................................................................................34

Spanish................................................................................................36

Portuguese...........................................................................................38

Polish...................................................................................................40

Russian................................................................................................42

Arabic..................................................................................................44

Japanese..............................................................................................46

P4MST-890

3

CHAPTER 1: INTRODUCTION

1.1 BEFORE YOU START

Tha nk yo u fo r choo sing our product. Before you sta rt installing the

mo the rboa rd , plea se make sure you fo llow the ins tructio ns be low:

 Prepare a dry and stable working environment with

s ufficie nt ligh ting .

 Always disconnect the computer from power outlet

be fore ope ra tion.

 Befo re you take the mo the rboa rd ou t f rom a n ti-s ta tic

bag, ground yourself properly by touching any safely

grounde d appliance, or use gro unded wrist strap to

remove the static charge.

 Avo id tou ch ing the compone nts o n mo the rboa rd o r the

rear side of the boa rd unless necessary. Hold the board

on the edge , do not try to bend or flex the board.

 Do not lea ve any unfastene d small parts inside the

case after installation. Loose parts will cause short

circuits which ma y damage the equipment.

 Keep the computer from dangerous area, such as heat

source , humid a ir and wa te r.

1.2 PACKAGE CHECKLIST

z HDD Cable X 1

z Use r’s Manua l X 1

z Fully Setup Driver CD X 1

z Rear I/O Panel for ATX Case X 1

z FDD Cable X 1 (optional)

z Se ria l ATA Cab le X 1 (op tiona l)

z USB 2.0 Cable X1 (optional)

z S/PDIF Cable X 1 (optional)

z Se ria l ATA Po we r Cab le X 1 (o ptio nal)

Motherboard Manual

4

1.3 MOTHERBOARD FEATURES

SPEC

CPU

LGA 775

Intel Core 2Duo

/

Pe ntium 4

/

Pe ntium D

/

Celeron D pr ocessor up to 3.8 GHz

*It is recommended to use processors

with 95W power consumption.

Supports Hy per Tra nsport/ Execute Disable

Bit/ Enhanced Intel S peedStep®/ Intel

Extended Memory 64 technology

FSB 533 / 80 0 / 106 6 MHz

Chipset

VIA P4M890

VIA VT8237A

Graphic Integrated i n U niChrome Pro Chipset Max Share d Video Memory is 64 MB

Super I/O

ITE IT 87 12F

Provides the most commonly used

legacy Super I/O functionality.

Low Pin C ount Interf ace

Environment Control initiatives,

H/W Monitor

Fan Spee d Co ntroller

ITE's "Smart G uardia n" fu nc tion

Main

Memory

DIMM Slots x 2

Supports DDR2 533

Each DIMM supports

256/512MB/1GB/2GB DDR2

Max Memory C apicity 4GB

Single Channel Mode DDR2 memory module

Registered DIMM and ECC DIMM is not

supported

IDE Integrated I DE Controller

Ultra DMA 33~133 Bus Master Mode

supports PIO Mo de 0~4,

SATA Integrated Seri al ATA Controller

Data transfer rates up to 1.5 Gb/s.

SATA Version 1.0 specification compliant.

LAN PHY Realtek RTL 8201CL PHY

10 / 100 Mb/s auto negotiation

Half / Full duplex capability

Sound

Codec

ALC861VD

5.1 cha nnels a udio o ut

High- Defi nition Au dio s upport

PCI Express x 16 slot x1 Supports PCI express x16 expansion cards

PCI Express x 1 slot x1 Supports PCI express x1 expansion cards Slots

PCI slot x2 Supports PCI expansion cards

Floppy connector x1 Each connector supports 2 Floppy drives

IDE Connector x2 Each connector supports 2 IDE device

SATA Connector x2 Each connector supports 1 SATA devices

Front Panel Connector x1 Supports front panel facilities

Front Audi o Co nnector x1 Supports front panel a udio fu nction

On Board

Connector

CD-in Co nnec tor x1 Supports CD au dio-in f unc tion

P4MST-890

5

SPEC

S/PDIF o ut co nnector x1 Supports di gital a udio out fu nction

CPU Fan hea der x1

CPU Fan power s upply (with Smart Fa n

function )

System Fan header x1 System Fan Power supply

Clear CMOS head er x1 Restore CMO S data to fac tory d efa ult

USB connector x2

Each connector supports 2 front panel USB

ports

Power Connector (24pin) x1 Connects to Power supply

Power Connector (4pin) x1 Connects to Power supply

Back Panel

I/O

PS/2 Keyb oard x1

PS/2 Mouse x1

Serial Port x1

Printer Port x1

VGA Port x1

LAN port x1

USB Port x4

Audio Jack x3

Connects to PS/2 Keyboard

Connects to PS/ 2 Mo us e

Provide RS- 232 Serial connection

Connects to various types of device

Connects to mo nitor.

Connects to RJ-45 ethernet cable

Connects to USB devices

Provide A udio-I n/Out a nd microphone

connection

Board Size 190 mm (W) x 24 4 mm (L) Micro ATX form Fac tor

OS

Support

Windows 2000 / XP

Biostar Reserves the right to add or remove

support for any OS with or without notice.

1.4 REAR PANEL CONNECTORS

PS/2

Mouse

PS/2

Keyboard

USBX2USBX2

LAN

COM1 VGA

Printer Port

Line I n /

Surround

Line Out

Mic In 1/

Bass/ Center

Motherboard Manual

6

1.5 MOTHERBOARD LAYOUT

Super

I/O

DIMM1

DIMM2

FDD1

PCI-EX1_1

PCI-EX16

PCI 1

PCI2

JPANEL1

JUSB2

JUSB3

JATXPWR1

JCFAN1

JATXPWR2

JSAT A1

JSATA2

Codec

JCDIN1

JSFAN1

BAT 1

BIOS

VIA

VT8237A

LGA775

CPU1

P4M890

JAUDIOF1

JKBMS1

JUSB1

JUSBLAN1

C

O

M

1

J

C

O

M

1

JVGA1

JAUDIO1

JSPDIF_OUT1

IDE1

JC MOS 1

LAN

IDE2

JUSBV2

JUSBV1

JP RNT 1

No te: represents the 1■

st

pin.

P4MST-890

7

CHAPTER 2: HARDWARE INSTALLATION

2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU)

Special Notice:

Remove Pin Cap before installation, and make good preservation

for future use. When the CPU is removed, cover the Pin Cap on the

empty socket to ensure pin legs won’t be damaged.

Pin Cap

Step 1: Pull the socket locking lever out from the socket and then raise

the lever up to a 90-degree angle.

Motherboard Manual

8

Step 2: Look for the triangular cut edge on socket, and the golden dot on

CPU should point forwards this triangular cut edge. The CPU will

fit only in the correct orientation.

Step 2-1:

Step 2-2:

Step 3: Hold the CPU down firmly, and then lower the lever to locked

position to complete the installation.

Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it

on the retention frame. Connect the CPU FAN power cable into

the JCFAN1. This completes the installation.

P4MST-890

9

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan

cable and connector may be different according to the fan manufacturer.

Connect the fan cable to the connector while matching the black wire to

pin#1.

JCFAN1: CPU Fan Header

Assignment

1 Ground

2 +12V

3 FAN RPM rate

sense

14

JCFAN1

4 Smart Fan

Control

JSFAN1: System Fan Header

Assignment

1 Ground

2 +12V

13

JSFAN1

3 FAN RPM rate

sense

Note:

The JSFAN1 support 3-pi n head connector. When connecti ng with wires onto connectors,

please note that the red wire is the positi ve and should be connected to pin#2, and the

black wire is Ground and should be c onnected to GND.

Motherboard Manual

10

2.3 INSTALLING SYSTEM MEMORY

A. Memory Modules

DIMM1

DIMM2

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a

DIMM on the slot such that the notch on the DIMM matches the

break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining

chip snap back in place and the DIMM is properly seated.

B. Memory Capacity

DIMM Socket

Location

DDR Module

To t a l Me m o r y

Size

DIMM1 256MB/512MB/1GB/2GB

DIMM2 256MB/512MB/1GB/2GB

Max is 4GB.

P4MST-890

11

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,

720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the

provided floppy drive ribbon cables.

34

33

1

2

IDE1/IDE2: Hard Disk Connectors

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO

Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality. It has two

HDD connectors IDE1 (primary) and IDE2 (secondary).

The IDE connectors can connect a master and a slave drive, so you can

connect up to four hard disk drives. The first hard drive should always be

connected to IDE1.

IDE2IDE1

21

3940

Motherboard Manual

12

PCI-EX16: PCI-Express x16 Slot

- PCI-Express 1.0a compliant.

- Maximum theoretical realized bandwidth of 4GB/s simultaneously per

direction, for an aggregate of 8GB/s totally.

PCI-EX1_1: PCI-Express x1 Slot

- PCI-Express 1.0a compliant.

- Data transfer bandwidth up to 250MB/s per direction; 500MB/s in total.

- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

- 2X bandwidth over the traditional PCI architecture.

PCI-EX16

PCI-EX1_1

PCI1~PCI2: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for expansion

cards. This PCI slot is designated as 32 bits.

PCI1

PCI2

P4MST-890

13

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 HOW TO SET UP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is

placed on pins, the jumper is “close”, if not, that means the jumper is

“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SET T ING S

JPANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep

button and speaker connection. It allows user to connect the PC case’s front

panel switch functions.

1

8

16

SLP

PWR_LED

On/Off

RST

HLED

SPK

++

+

9

-

Pin Assignment Functio n Pin Assignment Functio n

1 +5V 9 Sleep control

2 N/A 10 Ground

Sleep button

3 N/A 11 N/A N/A

4 Speaker

Speaker

Connector

12 Power LED (+)

5 HDD LED (+) 13 Power LED (+)

6 HDD LED (-)

Hard drive

LED

14 Power LED (-)

Power LED

7 Ground 15 Power button

8 Reset control

Reset button

16 Ground

Power-on button

Motherboard Manual

14

ATX Power Source Connector: JATXPWR1

JATXPWR1 allows user to connect 24-pin power connector on the ATX power

supply.

1

12

13

24

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V

14 -12V 2 +3.3V

15 Ground 3 Ground

16 PS_ON 4 +5V

17 Ground 5 Ground

18 Ground 6 +5V

19 Ground 7 Ground

20 NC 8 PW_OK

21 +5V 9 Standby Voltage+5V

22 +5V 10 +12V

23 +5V 11 +12V

24 Ground 12 +3.3V

JATXPWR2: ATX Power Source C onnector

By connecting this connector, it will provide +12V to CPU power circuit.

Assignment

1 +12V

2 +12V

3 Ground

1

23

4

4 Ground

P4MST-890

15

JUSB2/JUSB3: Headers for USB 2.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC front panel,

and also can be connected with internal USB devices, like USB card reader.

Assignment

1 +5V (fused)

2 +5V (fused)

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 Key

1

2

9

10

JUSB2

JUSB3

10 NC

JUSBV1/JUSBV2: Power Source Headers for USB Ports

Pin 1-2 Close:

JUSBV1: +5V for USB ports at JUSB1/JUSBLAN1.

JUSBV2: +5V for USB ports at front panel (JUSB2/JUSB3).

Pin 2-3 Close:

JUSBV1: USB ports at JUSB1/JUSBLAN1 are powered by +5V standby

voltage.

JUSBV2: USB ports at front panel (JUSB2/JUSB3) are powered by +5V

standby voltage.

31

Pin 1-2 close

13

JUSBV1

JUSBV2

13

3

1

Pin 2-3 close

Note:

In order to support this function “Power-On system vi a USB device,” “JUSBV1/ JUSBV2”

jumper cap should be placed on Pin 2-3 individuall y.

Motherboard Manual

16

JAUDIOF1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front

panel. It will disable the output on back panel audio connectors.

Pin Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

6 Jack Sense

7 Front Sense

8 Key

9 Left line in

10 Jack Sense

19

210

JCDIN1: CD-ROM Audio-in Connector

This connector allows user to connect the audio source from the variaty devices,

like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.

Assignment

1 Left Channel Input

2 Ground

3 Ground

14

4 Right Channel Input

JSPDIF_OUT1: Digital Audio-out Connector

This connector allows user to connect the PCI bracket SPDIF output header.

Assignment

1 +5V

2 SPDIF_OUT

13

3 Ground

P4MST-890

17

JCMOS1: Clear CMOS Header

By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting

and the CMOS data, please carefully follow the procedures to avoid damaging

the motherboard.

13

Pin 1-2 Close:

Normal Operation (default).

13

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

JSATA1~JSATA2: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 2 channels SATA interface,

it satisfies the SATA 1.0 spec and with transfer rate of 1.5Gb/s.

Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

147

JSATA1

JSATA2

147

7 Ground

Motherboard Manual

18

CHAPTER 4: USEFUL HELP

4.1 D

RIVER INSTALLATION NOTE

After you installed your operating system, please insert the Fully Setup

Driver CD into your optical drive and install the driver for better system

performance.

You will see the following window after you insert the CD

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you ins ert the Driver CD, please use file browser to

locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will

list the compatible driver for your motherboard and operating system.

Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide

will list the software available for your system, click on each software title

to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver

CD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version

of Acrobat Reader software from

http://www.adobe.com/products/acrobat/readstep2.html

P4MST-890

19

4.2 AWARD BIOS BEEP CODE

Beep Sound Meaning

One long beep followed by two short

beeps

Video card not found or video card

memory bad

High-low siren sound CPU overheated

System will shut down automatically

One Short beep when system boot-up No error found during POST

Long beeps every other second No DRAM detected or install

4.3 EXT RA INFORMATION

A. BIOS Update

After you fail to update BIOS or BIOS is invaded by virus, the

Boot-Block function will help to restore BIOS. If the following message

is shown after boot-up the system, it means the BIOS contents are

corrupted.

In this Case, please follow the procedure below to restore the BIOS:

1. Make a bootable floppy disk.

2. Download the Flash Utility “AWDFLASH.exe” from Machspeed's

website

3. C

onfirm motherboard model and download the respectively BIOS

from Biostar website.

4. Copy “AWDFLASH.exe” and respectively BIOS into floppy disk.

5. Insert the bootable disk into floppy drive and press Enter.

6. System will boot-up to DOS prompt.

7. Type

“Awdflash xxxx.bf/sn/py/r” in DOS prompt.

(

xxxx means BIOS name.)

8. System will update BIOS automatically and restart.

9. The BIOS has been recovered and will work properly.

Motherboard Manual

20

B. CPU Overheated

If the system shutdown automatically after power on system for

seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown

automatically to avoid a damage of the CPU, and the system may not

power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection

function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.

(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

La pagina sta caricando ...

Mach P4MST-890 Setup Manual

Mach P4MST-890 Setup Manual

in altre lingue

Altri documenti