Ericsson Dialog 4186 High Manuale utente

?

Cover Page Graphic

Place the graphic directly on the page, do not care about

putting it in the text flow. Select Graphics > Properties

and make the following settings:

• Width: 15,4 cm (Important!)

• Height: 11,2 cm (May be smaller)

• Top: 5,3 cm (Important!)

• Left: -0,3 cm (Important!)

This text should then be hidden.

Dialog 4186 High

Analog Telephone for MD110 Communication System

User Guide

Title

EN/LZT 103 72 R1A

3Dialog 4186 High

Table of Contents

page

Welcome .......................................................... 4

Description .......................................................6

Free Seating (optional) ....................................12

Incoming Calls ...............................................13

Outgoing Calls ...............................................16

During Calls ....................................................30

Phone Book ...................................................35

Call Forwarding ..............................................41

Absence Information (optional) .......................52

Messages ......................................................54

Group Features ..............................................60

Other Useful Features .....................................62

Settings ..........................................................70

Accessories ...................................................83

Installation ......................................................85

Troubleshooting ..............................................89

Glossary .........................................................90

Index ..............................................................91

Welcome

Dialog 4186 High4

Welcome

Welcome to the user guide for the Ericsson Dialog 4186 High

phone, in the Ericsson MD110 Communication System from

Ericsson. Its alliance of features and facilities effectively improves

communications for virtually any kind of organization.

There is a line of telephones designed for easy use in every

situation to take full advantage of these advanced features and

facilities.

Some markets use differing codes for some functions. In this guide,

all functions are described using the most common code. The

markets and their differing code is shown as a side note.

The user guide describes the facilities of the

Ericsson Dialog 4186 High phone as it is programmed at delivery

from the factory. There may be some differences in the way your

phone is programmed. Please consult your system administrator if

you need further information.

The latest version of this user guide can be downloaded from:

http://www.ericsson.com/enterprise/

5Dialog 4186 High

Welcome

Copyright

stored in retrieval systems, or transmitted in any form or by any

means, electronic, mechanical, photocopying, recording or

otherwise, without prior written permission of the publisher except

in accordance with the following terms.

If this publication is made available on Ericsson media, Ericsson

gives its consent to downloading and printing copies of the content

provided in this file only for private use and not for redistribution. No

parts of this publication may be subject to alteration, modification

or commercial use. Ericsson will not be liable for any damages

arising from use of an illegal modified or altered publication.

Warranty

ERICSSON MAKES NO WARRANTY OF ANY KIND WITH

REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED

TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. Ericsson shall not be

liable for errors contained herein nor for incidental or consequential

damages in connection with the furnishing, performance or use of

this material.

Declaration of Conformity

Hereby, Ericsson Enterprise AB, S-131 89 Stockholm,

declares that this telephone is in conformity with the essential

requirements and other relevant provisions of the R&TTE

directive 1999/5/EC.

Details to be found at:

http://www.ericsson.com/sdoc

Description

Dialog 4186 High6

Description

(bottom side)

22

18

2 3 4 5

6 7 8 9

10

11

13

14

15

16

17

19

20

21

1

24

23

12

7Dialog 4186 High

Description

1 Display

2x24 characters. Indicates call duration and date and time. See

section “Display information” on page 9.

2Alarm

To set, confirm or view an alarm. See section “Alarm Clock” on

page 62.

3 Scroll left

Scroll left in redial memory, menus and Phone book.

4 Scroll right

Scroll right in redial memory, menus and Phone book.

5 Phone book

Access the Phone book. See section “Phone Book” on page 35.

6Program

a. To activate the programming mode.

b. To show the duration of the last incoming call. See section “Call

Timer” on page 34.

7Delete

a. To delete the last entry. Also used as backspace function.

b. To cancel an alarm. See section “Alarm Clock” on page 62.

8Pause

Insert a pause if you have to wait for dial tone. Also used to snooze

an alarm. See sections “Wait for dial tone” on page 17, “Pause

length” on page 78 and “Alarm Clock” on page 62.

9Redial

Last number redial. The 20 last dialed numbers are stored for

redialling. See section “Last Number Redial” on page 18.

10 Message Waiting lamp

A flashing light indicates a waiting message. See section

“Messages” on page 54.

11 Programmable keys (function keys)

Ten keys for storing frequently called numbers. You can store two

numbers per key (first level and second level). See sections “Dial By

a Function Key” on page 24 and “Set the number of programmable

keys” on page 76.

12 Microphone

Used for handsfree conversation.

Description

Dialog 4186 High8

13 Mute

a. Switch microphone on or off. See section “Mute” on page 31.

b. To switch off the ring signal in idle mode or when ringing. See

sections “Silent ring” on page 15 and “Mute ring signal” on

page 15.

14 Loudspeaker on/off

Switch loudspeaker on or off. See section “During Calls” on

page 30.

15 Headset key

Activate headset. See section “Headset (optional)” on page 83.

16 R-key

Used for example to make an inquiry, to transfer a call or to

establish a conference, see section “During Calls” on page 30.

Note: Sometimes it is required to change the flash time for

the R-key, see section “Flash time” on page 77.

17 Volume control

To adjust the volume. See section “Handset, headset and

loudspeaker volume” on page 70.

18 Loudspeaker

19 Prog On/Off switch

Enable or disable the program key. See section “Enable/Disable

function key programming” on page 82.

20 Message Waiting switch

Switch Message Waiting indication on or off. Also used to reverse

the polarity in case of crossed line cables. See section “Message

Waiting indication” on page 82.

21 Data port

For connection of a modem, PC or other phone equipment.

22 Handset with hearing aid function

Please note: The handset may attract and retain small

metal objects in the earcap region.

23 Power adapter connection

24 Designation card

Use the Designation Card Manager to make and print your own

designation cards. The Designation Card Manager is included on

the Telephone Toolbox CD for MD110 Communication System. For

more information, please contact your Ericsson Enterprise certified

sales partner.

9Dialog 4186 High

Description

Display information

The display gives you visual feedback on all actions that you

perform. The size of the display is 2x24 characters.

Idle phone

When your phone is idle, the upper line shows your extension

number (if programmed, see section “Telephone ID” on page 75).

The lower line shows the date and the time.

Note: You can set different formats for the date and time,

see section “Date and Time” on page 73.

During a call

During a call, the display shows the Call Timer on the upper line to

the right. If you initiated the call, the dialed number will appear on

the second line to the right:

During programming

Furthermore, your display assists your actions during programming

and shows the activated menu, for example:

4455

01-15 10:38

4455 00:02:15

0-00460812345678

HEADSET PRESET

Description

Dialog 4186 High10

Tones and signals

The following different tones and signals are sent from the

exchange to your phone.

Tone characteristics

The tones shown in this section are the most used tones

worldwide. Many markets use a differing tone for one or more

situations.

Dial tone

Special dial tone

Ring tone or queue tone every 4 seconds

Busy tone

Congestion tone

Number unobtainable tone

Call waiting tone

Intrusion tone

Conference tone every 15 seconds (to all parties)

Verification tone

Warning tone, expensive route

11Dialog 4186 High

Description

Ring signals

Three different ring signals inform you about the type of the

incoming call. The signals shown in this section are the most used

signals worldwide. Many markets use signals that are adapted for

the local standards. If you get a signal that is not described or you

cannot identify, ask your system administrator.

Internal ring signal

External ring signal

Recall signal

(Callback reminder)

Free Seating (optional)

Dialog 4186 High12

Free Seating (optional)

The Free Seating function is used for persons who have an office

extension number but no phone set of their own. For example,

flexible office workers, persons mostly working outside the office,

etc. As a Free Seating user and working from the office, you logon

to any free phone set that temporarily will be assigned with your

extension number and your system authorities.

To log on

u Lift the handset.

*11* Dial.

z* Enter the authorization code and press.

z# Enter your phone number and press.

d Replace the handset to finish the procedure.

The display shows your phone number.

Note: An earlier version of the Free Seating function uses

another procedure: To log on, dial

* 1 0 * extension No. #.

To log off

u Lift the handset.

#11# Dial.

d Replace the handset to finish the procedure.

Note: An earlier version of the Free Seating function uses

another procedure: To log off, dial

# 1 0 #.

13Dialog 4186 High

Incoming Calls

Answer calls

A ring signal indicates an incoming internal or external call. You can

see the duration of incoming calls, see section “Call Timer” on

page 34.

Note: To answer calls via the headset, see section

“Headset (optional)” on page 83.

To answer an incoming call:

u Lift the handset.

Handsfree

Â Press without lifting the handset.

You are connected to the caller via the loudspeaker and

microphone.

ÄÂ Press to terminate a handsfree call.

On another extension

You can answer a call to another extension from any phone in your

office.

uz Lift the handset and call the ringing extension.

You receive busy tone.

8 Press.

Note: France, press

4; Sweden, press 6

Incoming Calls

Dialog 4186 High14

Answer a second call

A call waiting tone will inform you, during a conversation, that a

second call is waiting on your phone. You have two options.

Option 1:

Finish the ongoing call:

d Replace the handset.

The new call will be signalled on your phone.

u Lift the handset to receive the new call.

Option 2:

Ask your conversation partner to wait:

¸d Press and replace the handset.

The waiting call will be signalled on your phone.

u Lift the handset to receive the new call.

After finishing the new call:

d Replace the handset.

Your first call will be signalled on your phone.

u Lift the handset to receive the first call again.

15Dialog 4186 High

Incoming Calls

Mute ring signal

If the phone rings at an inconvenient moment:

É Press to suppress the ringing.

The ring signal will silence. The Loudspeaker key is flashing and the

display shows:

Note: When a headset is connected, both the

Loudspeaker key and the Headset key are flashing.

The display will toggle between

RINGER OFF and

INCOMING CALL. When the calling person hangs up, the Mute

key lamp flashes and the display steadily shows

RINGER OFF, i.e.

the phone is set for Silent ring (see below).

Press any key to turn the ring signal on again.

Silent ring

If you do not want to be disturbed by the ring signal but still want to

be able to answer an incoming call, you can switch off the ring

signal.

É Press to switch off the ring signal.

The display shows

RINGER OFF, and the Mute key lamp flashes

to indicate silent ringing. The ring signal will automatically be

switched on the next time you lift the handset or press any key.

4455 RINGER OFF

01-15 10:38

Outgoing Calls

Dialog 4186 High16

Outgoing Calls

Make calls

Notes:

To make calls via the headset, see section “Headset

(optional)” on page 83.

You can see the duration of outgoing calls, see section “Call

Timer” on page 34.

How to make internal and external calls.

u Lift the handset and dial either:

z An extension number to make an internal call.

Or:

0z The digit or digits to get an external line and the external

number.

Note: Which digit to press for external call access,

depends on the configuration of the system.

d Replace the handset to end the call.

Notes:

You can make your calls faster, using Common Speed

Dialing numbers and by programming your own Speed

Dialing numbers, see section “Speed Dialing” on page 23.

If you receive a queue tone when the digit or digits to get an

external line are dialed (optional function Least Cost Routing

is used in the system), keep waiting. Once a line becomes

free, you will receive a dial tone. If a warning tone is heard,

the selected line is marked “Expensive”.

17Dialog 4186 High

Outgoing Calls

Handsfree

With the handset on hook.

Â Press without lifting the handset.

z Dial the number.

You are connected to the caller via the loudspeaker and

microphone.

ÄÂ Press to terminate a handsfree call.

Wait for dial tone

Sometimes it is required to wait for a new dial tone after dialing the

prefix digit when making an external call. In such situations, you

must store the pause for a new dial tone into the number:

° Press.

Note: You can program the length of a pause, see section

“Pause length” on page 78.

Number presentation restriction

If you do not want your name and number to be displayed to the

person you are calling, you can use the following procedure.

Notes:

This function is only available in newer versions of the

exchange, and it might be blocked for use on your

extension (programmed by your system administrator).

The number presentation restriction is only valid for the

ongoing call, i.e. the procedure has to be repeated the next

time you want to use it.

u Lift the handset.

*42# Dial and wait for a new dial tone.

z Dial the number.

Your name and number is not indicated on the called person´s

display.

Outgoing Calls

Dialog 4186 High18

Individual External Line

To make a call on a specific external line:

u Lift the handset.

*0* Dial.

z# Dial the individual external line number and press.

z Dial the digit or digits to get an external line and the external

number.

Last Number Redial

When you initiate a call (internal or external) the phone automatically

stores all the dialed digits, irrespective of whether the call was

successful or not.

Your phone stores the last 20 dialed numbers. The call position

and the Call Timer record for each number is also stored. Stored

numbers can consist of maximum 24 digits. If you have dialed the

same number more than one time, this number will only be saved

once.

The last dialed number is always the first one that appears in the

display when you press the Redial key, for example:

POS 1 means that the number is stored at the first position.

Note: To redial a number that incorporates a wait for a new

dial tone, you must indicate to the telephone where in the

number it must pause and wait for the new dial tone. To do

this, press the Pause key at the proper place in the number.

See section “Wait for dial tone” on page 17.

µ Press.

The display shows the last dialed number. If you are looking for

another number, use the Scroll keys to find the required number.

u Lift the handset to redial the number.

POS 1 00:02:15

0-00460812345678

19Dialog 4186 High

Outgoing Calls

Last External Number Redial

When you initiate an external call the system automatically stores all

the dialed digits, irrespective of whether the call was successful or

not.

Note: To redial a number that incorporates a wait for a new

dial tone, you must indicate to the telephone where in the

number it must pause and wait for the new dial tone. To do

this, press the Pause key at the proper place in the number.

See section “Wait for dial tone” on page 17.

u Lift the handset.

*** Press to redial the last dialed external number.

Note: Finland and Sweden, dial

* * 0

When you receive a busy tone

If you call an extension and receive a busy tone or get no answer or

all external lines are busy you can use these methods:

Callback

If a called extension is busy or there is no answer:

6 Press.

Note: France, Finland and Sweden, press

5

d Replace the handset to finish procedure.

You are called back (recall ring signal) when the ongoing call is

finished or the next time a new call is finished. You have to answer

within eight seconds, otherwise the Callback service is cancelled.

u Lift the handset when you are called back.

The system calls the extension.

Note: Callbacks can be activated on several extensions at

the same time.

Outgoing Calls

Dialog 4186 High20

If all external lines are busy (after dialing the digit or digits to get a

line):

6 Press.

Note: France, Finland and Sweden, press

5

z# Dial the external number and press.

d Replace the handset to finish procedure.

When an external line becomes free, you will be called back (recall

ring signal). You have to answer within eight seconds, otherwise

the Callback service is cancelled.

u Lift the handset when you are called back.

The system calls the external number.

Note: Only one Callback can be activated on a busy

external line.

Cancel any single Callback

u Lift the handset.

#37* z Dial and enter the extension number.

Note: To cancel a single Callback on a specific external

line, dial the digit or digits to get a line instead of the

extension number.

#d Press and replace the handset.

Cancel all Callbacks

u Lift the handset.

#37# Dial.

d Replace the handset.

La pagina sta caricando ...

Ericsson Dialog 4186 High Manuale utente

Ericsson Dialog 4186 High Manuale utente

in altre lingue

Documenti correlati

Altri documenti