Foster 7341/645 Use And Installation Manual

Marca: Foster

Modello: 7341/645

Categoria: Piani cottura

Tipo: Use And Installation Manual

model: 7341/645

induction vitroceramic hob

piano cottura induzione in vetroceramica

glaskeramik-induktions-kochfeld

table de cuisson induction en vitrocéramique

placa inducción en vitrocerámica

[EN] Use and installation manual 2

[IT] Manuale d’istallazione e uso 20

[DE] Bedienungs-und Montageanleitung 38

[FR] Manuel d’installation et d’utilisation 56

[ES] Manual de instalación y uso 74

ENGLISH

[EN] use and installation manual

TABLE OF CONTENTS

PART 1 - User Guide

important safety instructions 3

Intended use 3

Children at the cooktop 3

Technical safety 3

Proper use 4

induction cooking 6

Advantages of induction cooking 6

Cookware 6

Correct cookware positioning 7

overview 8

Control panel sensor keys 8

Display symbols and leds 9

using the cooktop 10

Switching the appliance on 10

Switching the appliance off 10

Switching the cooking zones on 10

Switching the cooking zones off 10

Pot detection 10

Residual heat 10

Timer 10

Egg timer/reminder 11

Pause 11

Recall 11

Control lock 12

Child safety lock 12

Special programs: Warming, Melt, Simmer,

Power Boost, Automatic warm-up 12

Safety switch 13

Bridge (Flexible cooking zones) 14

Power management 15

Technical speciﬁcations 15

troubleshooting 16

cleaning and care 18

Important information 18

General information 18

Cleaning the cooktop 18

protecting the environment 19

Disposal of the packing material 19

Disposal of your old appliance 19

Energy-saving advice 19

PART 2 - Installer Guide

installation 20

Installing the cooktop 20

Positioning 22

Ventilation 22

Worktop cut-out 22

Electrical connections 23

Dear Customer,

congratulations on your purchase.

Please carefully read the instructions for installation and use before using the

cooktop for the ﬁrst time.

The instructions contain important information for installation, safety, use and

maintenance.

This will protect you from injury and prevent damage to the cooktop.

The manufacturer will not be held liable for damage caused by failure to comply with the

safety instructions and warnings.

Keep the instructions in a safe place and pass them along to any future owner.

ENGLISH

important safety instructions

PART 1 - User Guide

WARNING!

READ THE OPERATING INSTRUCTIONS CAREFULLY

BEFORE USING THE COOKTOP!

THIS APPLIANCE IS INTENDED FOR

RESIDENTIAL COOKING ONLY.

Intended use

• Use the cooktop only in household-type situations for the preparation and

warming of food. All other types of use are not permitted.

• This cooktop is not intended for outdoor use or in mobile locations such as

ships.

• Individuals who are incapable of using the appliance safely because of their

physical, sensory or mental capabilities or their lack of experience or knowledge

must not use this appliance without supervision or instruction by a responsible

person.

Children at the cooktop

• Children under 8 years of age must be kept away from the cooktop unless they

are under constant supervision.

• Children 8 years and older must only be allowed to use the cooktop if they have

been given supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved.

• Children shall not play with the appliance.

• Cleaning and user maintenance shall not be made by children without supervision.

• Risk of suffocation! Children could wrap themselves in packaging materials

(e.g. foil) or pull it over their heads during play and suffocate. Keep packaging

materials out of the reach of children.

• Risk of burns! Keep the spaces above and behind the cooktop clear of any

items that could draw the interest of a child. Otherwise, a child could be tempted

to climb onto the cooktop.

• Risk of scalding and burns! ALWAYS turn pot/pan handles inward so that they

do not extend out from the cooktop, where they could be grabbed. This helps

reduce the risk of burns and scalding.

• If available, use the Child Safety Lock to prevent children from turning the cooktop

on. When using the cooktop, turn on the Control Lock to prevent children from

changing the (selected) settings.

Technical safety

• Installation, repair and maintenance work should only be performed by an

authorized service technician. Work by unqualiﬁed persons could be dangerous

for the user.

Safety da Miele KM 6310

ENGLISH

important safety instructions

• Connection of the cooktop to the electrical power supply must only be performed

by a qualiﬁed electrician.

• A damaged cooktop can be dangerous. Before installing the cooktop, check for

visible damage. Do not operate a damaged appliance.

• The electrical safety of this cooktop can only be guaranteed if proper grounding

has been installed in compliance with applicable regulations. It is imperative that

this basic safety requirement be met. If in doubt, have the house wiring checked

by a qualiﬁed electrician.

• Before installation, make sure that the voltage and frequency on the cooktop’s

data plate correspond with the household electrical supply. These ratings

must match to prevent damaging the cooktop. If in doubt, consult a qualiﬁed

electrician.

• Before installation, maintenance or repair work is performed, disconnect the

cooktop from the electrical power supply.

• Multiple power outlets or extension cords are not safe (risk of ﬁre). Do not use

them to connect the cooktop to the electrical power supply.

• To ensure safe operation, use the cooktop only when it has been properly

installed.

• Do not under any circumstances open the cooktop housing. Any contact with

connections carrying voltage or changes to the electrical or mechanical set-up

will endanger you and may impair the functioning of the cooktop.

• Only with original spare parts can the manufacturer guarantee the safety of the

appliance. Defective components should only be replaced with original parts.

• Risk of electric shock! If the cooktop is defective or chipped, cracked or broken

in any way, immediately switch it off and do not continue to use it. Disconnect it

from the electrical power supply.

• WARNING: If the supply cord of the appliance is damaged, it must be replaced

by the manufacturer, its service agent or similarly qualiﬁed persons in order to

avoid a hazard.

Proper use

• WARNING: The appliance and its accessible parts become hot during use.

Care should be taken to avoid touching heating elements.

• WARNING: Unattended cooking on a hob with fat or oil can be dangerous and

may result in ﬁre. NEVER try to extinguish a ﬁre with water, but switch off the

appliance and then cover ﬂame e.g. with a lid or a ﬁre blanket.

• WARNING: The cooktop is hot during use and remains so for some time after

being switched off. The risk of burns remains until the residual heat indicators

have gone out.

• CAUTION: The cooking process has to be supervised. A short term cooking

process has to be supervised continuously.

• DANGER OF FIRE: Do not store items on the cooking surfaces!

• Metallic objects such as knives, forks, spoons and lids should not be placed on

ENGLISH

important safety instructions

the hob surface since they can become hot.

• Always switch the cooking zones off after use!

• Spray cans, ﬂammable liquids or ﬂammable materials can ignite if heated. If

there is a drawer below the appliance, do not store ﬂammable items in the

drawer. If there is a cutlery tray below the cooktop, it must be made of heat-

resistant material.

• Flames can set ﬁre to the grease ﬁlters in the exhaust hood. Never ﬂambé food

under an exhaust hood.

• Never heat empty cookware or an empty pot! This can damage the glass

ceramic surface.

• Never use the cooktop to heat closed cans. The increased pressure can cause

the cans to explode.

• If using a small appliance (e.g. a hand mixer) in the vicinity of the cooktop, make

sure that the power cord does not come into contact with the hot cooktop. The

insulation of the cord could get damaged.

• Salt, sugar, and grains of sand or dirt (e.g. from fresh vegetables) between the

cookware and the cooktop can cause scratches. Keep cooktop and cookware

clean.

• Rough cookware can scratch the glass ceramic surface. Use only pots and

pans with a smooth bottom.

• Even light objects such as a salt shaker can cause cracks and chips if they

fall on the glass ceramic surface. Do not drop anything on the glass ceramic

surface.

• Hot objects on the sensor areas or indicators can damage the electronics

underneath. Never place hot pots or pans on the sensor areas or indicators.

• Metal objects stored in a drawer under the cooktop can become hot when the

cooktop is in heavy use over a longer period of time. Do not store metal objects

in a drawer under the cooktop!

• The appliance is not intended to be operated by means of an external timer or

separate remote-control system.

• For users who wear a pacemaker: When the cooktop is in use it is surrounded

by an electromagnetic ﬁeld. It is unlikely that this will affect a pacemaker.

However, if in doubt consult the manufacturer of the pacemaker or your doctor.

• Objects affected by electromagnetic ﬁelds, for instance credit cards, CDs and

calculators, should be kept away from the cooktop when it is on.

• Because induction heating works so quickly, the temperature of the cookware

bottom can quickly reach the ignition point of oils and fats. Never leave the

cooktop unattended during use!

• The cooktop is equipped with a cooling fan. If there is a drawer below the

installed appliance, you will need to ensure there is enough space to allow for

ventilation. Do not use the drawer to store sharp or small objects or paper. They

could pass through or be sucked into the vents in the housing and damage the

fan blades or otherwise interfere with cooling.

ENGLISH

induction cooking

Advantages of induction cooking

When cooking with induction, heat is generated directly in the base of the pan.

This provides many beneﬁts for you:

• Time saving when boiling and frying. Cookware is heated directly.

• Less energy is consumed.

• Easy cleaning and maintenance. Spilled food does not burn onto the cooktop

so quickly.

• Controlled supply of heat and increased safety. The burner reacts immediately

to any power change, so heating can be dosed precisely. Heating is interrupted

when you remove the cookware from the burner even if the burner is still

switched on.

Cookware

Only ferromagnetic cookware made of the following materials is suitable for

induction cooktops:

• Enameled steel

• Cast iron

• Induction-capable cookware of stainless steel.

To determine whether the cookware is

suitable, check whether the base of the pot

or pan attracts a magnet.

There are other induction-capable pots

and pans whose bases are not completely

ferromagnetic. If the base of the cookware it’s

not completely ferromagnetic, only the area

that is magnetizable will get hot. Thus it can

happen that the heat is not distributed evenly.

To get good cooking results, we recommend that the dimension of the

ferromagnetic area of the cookware match the size of the burner.

Unsuitable cookware

Do not ever use adapter plates for induction or cookware made of:

• Traditional stainless steel

• Glass

• Clay

• Copper

• Aluminum

ENGLISH

Correct cookware positioning

INCORRECT CORRECT

Cookware not centered on Cooking Zone

surface.

Cookware centered correctly on Cooking

Zone surface.

Curved or warped pan bottoms or sides. Flat pan bottom & straight sides.

Pan does not meet the minimum size

required for the Cooking Zone.

Pan size meets or exceeds the

recommended minimum size for the

Cooking Zone.

Pan bottom rests on cooktop trim or does

not rest completely on the cooktop surface.

Pan rests completely on the Cooktop

surface.

Heavy handle tilts pan. Pan is properly balanced.

induction cooking

ENGLISH

overview

Control panel sensor keys

The appliance is operated using the control panel sensor keys.

Functions are controlled by touching the sensor keys and conﬁrmed by displays

and acoustic signals. Touch the sensor keys from above, without covering other

sensor keys.

9 9

02 5

min

Sensor

key

Function

Power key - press to switch on the appliance

Control Lock key - press to activate ‘‘Control lock” function

Pause/Recall key - press to activate ‘‘Pause’’ or ‘‘Recall’’ function

‘Programs’ key - press to activate ‘‘Warming’’, ‘‘Melt’’ or ‘‘Simmer’’

program

Timer - press [+] and/or [-] to activate and set a cooking zone

“Timer”, or to set an ‘‘Egg timer/Reminder”

Slidebar - Slide left or right to activate and set the heat level of a

cooking zone

WARNING! Risk of burns from heat emitted.

Lengthy cooking on higher settings with larger cookware on the front cooking

zones can heat the sensor ﬁelds. Take care when touching sensor ﬁelds.

ENGLISH

Display symbols and leds

Display Description

active function led - indicates that the corresponding function/zone

is active

timer/egg timer led - cooking zone timer active / egg timer active

bridge led - indicates that the bridge function is active

warming led - indicates that the ‘‘warming’’ program is active (the

cooking zone heat level is set at 42°)

melt led - indicates that the ‘‘melt’’ program is active (the cooking

zone heat level is set at 70°)

simmer led - indicates that the ‘‘simmer’’ program is active (the

cooking zone heat level is set at 94°C)

a 4

no timer setting made

0 4

the cooking zone is on and ready to be set

1 4

9 4

active cooking zone heat level

025

Timer display

0 4

pot detection - cookware is unsuitable, too small or no cookware

has been placed on the cooking zone

h 4

residual heat - indicates that the cooking zone is still hot. Warning!

p 4

power boost function is activated

a 4

automatic warm-up function is activated

e 4

+ digit

error - malfunction has occurred. (Refer to ‘‘troubleshooting’’ chapter)

WARNING! RISK OF BURNS FROM RESIDUAL HEAT

Residual heat indicator

After being switched off, the cooking zones need

some time to cool down.

Look at the residual heat indicator.

Tips: Residual heat can be used for melting and keeping food warm.

overview

ENGLISH

Switching the appliance on

Press the Power key to switch the appliance on.

All the displays relative to the cooking zones switch on in the standby position

«0».

The control unit remains active for 10 seconds. If no cooking zone is selected

within this time, the appliance switches off automatically.

Switching the appliance off

To turn off the appliance entirely hold down the power key.

Switching the cooking zones on

Switch on the appliance then adjust the heat setting using the corresponding

cooking zone slidebar within 10 seconds. The heat level of each single cooking

zone can be set in 9 different positions and will be shown in the corresponding

cooking zone display with a number ranging from «1» to «9». Slide right on the

slidebar to increase the heat level, slide left to decrease it.

Switching the cooking zones off

To switch a cooking zone off bring its level back to «0» by sliding left on the

corresponding slidebar.

Pot detection

Each induction cooking zone has a pot detection minimum limit, which

varies according to the material of the cookware being used.

For this reason, you should choose the cooking zone which is most suitable for

the diameter of the cookware you are going to use.

If the symbol

0 4

appears on the cooking zone display, it means that:

• The cookware used is not suitable for induction cooking.

• The cookware diameter is smaller than the one allowed by the hob.

• No cookware is on the cooking zone.

For more details about this feature refer to chapter ‘‘induction cooking”.

Residual heat

If the temperature of the cooking zone is still high (over 50°C) after it has been

switched off, the relative display will indicate the symbol «H» (residual heat).

The symbol will stay on even when the appliance is switched off and will only

switch off when the burn risk in no longer present.

Timer

This function allows you to set the time from «1.00» (1 minute) to «1.59» (1 hour

and 59 minutes) for the automatic switch off of a cooking zone.

Switch on a cooking zone by sliding on the slidebar to adjust the heat level. To

activate the timer press simultaneously the [+] and [-] keys on the timer area until

using the cooktop

ENGLISH

the clock symbol lights up beside the cooking zone display, then set the desired

time using the timer [+] and [-] keys within 5 seconds. Wait for 5 seconds for the

automatic conﬁrmation. The time countdown will be start on the timer display.

When time elapses the cooking zone will automatically switch off, the timer

display will show a ﬂashing «000» and an acoustic signal will be heard. Press the

[+] or [-] key on the timer area to stop the signals.

To disable the timer of a cooking zone press repeatedly and simoultaneously

the [+] and [-] keys on the timer area until the clock symbol lights up beside

the display of the desired cooking zone, press again the timer [+] and [-] keys

simoultaneously, then bring the timer value back to «000»

by using the timer [-]

key. Wait for 5 seconds for the automatic conﬁrmation.The clock symbol beside

the cooking zone display goes off.

Egg timer/reminder

When no cooking zone is active it is possible to set an acoustic reminder which

stays active after switching the appliance off. When the Egg timer/Reminder

function is active, the Timer function cannot be selected.

To enable this function press simoultaneously the timer [+] and [-] keys. The

clock symbol lights up below the timer display. Set the time, ranging from «1.00»

(1 minute) to «1.59» (1 hour and 59 minutes), by pressing the [+] and [-] keys.

Wait for 5 seconds for the automatic conﬁrmation. The time countdown will be

shown on the timer display.

When time elapses the display will show a ﬂashing «000» and an acoustic signal

will be heard. Press the [+] or [-] key on the timer area to stop the signals.

To disable the Egg timer/Reminder function press simoultaneously the timer [+]

and [-] keys. The clock symbol lights up below the timer display. Bring the timer

value back to «000»

by using the [-] key. Wait for 5 seconds for the automatic

conﬁrmation.The clock symbol beside the timer display goes off.

Pause

When at least one cooking zone is operating it is possible to momentaneously

pause the appliance switching off the cooking zones.

To enable this function press the Pause/recall key. The relative led lights up

and all the cooking zone displays show the symbol

«II»

. Previously programmed

timers will be stopped.

The pause can last for maximum 10 minutes. If this status is not terminated

within this time the appliance switches off.

To disable the Pause function press the Pause/recall key and slide right on the

ﬂashing slidebar within 10 seconds.

Recall

When the appliance has been switched off by mistake it is possible to quickly

recall the previously active settings by pressing the Power key within 5

using the cooktop

ENGLISH

seconds, then pressing the Pause/recall key within another 5 seconds. If the

recall function is available the relative led will be ﬂashing when the appliance is

switched on again.

Control lock

Controls can be locked in order to prevent any risk of unintentional changes to

the settings (children, cleaning operations, etc.). To activate this function press

the Control Lock key. The relative led will light up. The function remains active

when the appliance is switched off and on again.

To disable the Control Lock function simply press the

Control Lock key. The

relative led will go off.

Child safety lock

This function serves the purpose of preventing children from switching on the

appliance even accidentally or intentionally.

The Child safety lock can only be activated with all the cooking zones off.

To activate this function press simoultaneously the

Control lock key and

the

Pause/Recall key, then again the Control Lock key. The symbol

«L

will

appear on all displays to conﬁrm your selection and the relative led will light up.

When the Child safety lock is enabled you can switch the appliance off. The

Child safety lock is still enabled when the appliance is switched on again.

To unlock the appliance permanently, press simoultaneously the

Control lock

key and the Pause/Recall key, then again the Pause/Recall key. In this case

the Child safety lock won’t be enabled when the appliance is switched on

again.

To unlock the appliance temporarily press simoultaneously the

Control lock

key and the Pause/Recall key. In this case the Child safety lock will still be

active each time the appliance is switched on again.

Special programs: Warming, Melt, Simmer, Power Boost,

Automatic warm-up

The cooktop has three special programs that have already been set to perform

special cooking operations.

• Warming

The ‘‘Warming’’ program sets the heat temperature of the selected cooking

zone at 42°C to keep food warm. To activate this program press the

Programs key once. The Warming led lights up besides the cooking zone

display.

• Melt

The ‘‘Melt’’ program sets the heat temperature of the selected cooking zone

at 70°C to melt chocolate, butter or the like. To activate this program press

using the cooktop

ENGLISH

the Programs key twice. The Melt led lights up besides the cooking zone

display.

• Simmer

The ‘‘Simmer’’ program sets the heat temperature of the selected cooking

zone at 94°C to bring to a boil slowly preparing sauces or soups and stews.

To activate this program press three times the Programs key, the Simmer

led lights up besides the cooking zone display.

• Power Boost

This program further reduces the cooking time of a certain cooking zone, by

bringing the temperature to the maximum heat level for 10 minutes.

At the end of this timeframe, the cooking zone heat level will automatically go

back to level «9». The use of this function is recommended for heating large

quantities of liquids (e.g. water to cook pasta) or food in a very short time.

To activate this program slide right on the slidebar until the «P» symbol appears

on the cooking zone display.

• Automatic warm-up

All cooking zones are equipped with an “automatic warm up” function. This

feature sets the cooking zone to the highest heat level for a certain period of

time and then automatically switches back to the cooking setting that was

originally set.

The lenght of time that the automatic warm up function operates depends on

the heat setting selected.

To activate the “automatic warm up” function on a cooking zone place your

ﬁnger on the slidebar at the desired heat level an hold the position until the

symbol «A», alternating with the selected heat level, appears on the cooking

area display.

Safety switch

The appliance has a safety switch that

automatically switches off the cooking

zones when they have been operating

for a certain amount of time at a given

heat level. In case of hot surface the

residual heat symbol

«H» is displayed.

HEAT LEVEL OPERATING

TIME LIMIT (hours)

1 - 2 6

3 - 4 5

5 4

6 - 7 - 8 - 9 1,5

using the cooktop

ENGLISH

Bridge (Flexible cooking zones)

This function allows you to combine the front cooking zone to the rear cooking

zone to create one large zone as shown below (a+b).

Pay attention in placing the cookware in the correct position on the cooking zones.

yes

no no

yes

a b c d

yes

To activate the Bridge function between two cooking zones press simoultaneously

on both slidebars. The bridge luminous symbol will appear on the side of the two

cooking zones display indicating that the function is active (see image below).

Now it is possible to set the heat level of the bridge zone.

6 0

02 5

min

NOTE: the settings of the brige zone are only enabled by the front cooking zone

slidebar and sensor keys.

To disable the Bridge function press simoultaneously on both cooking zones

slidebar.

using the cooktop

front zone commands rear zone commands

ENGLISH

Power management

All cooking zones are connected to one phase (see the

illustration). The phase has a maximum electricity loading of

3700 W/230V (see ‘‘Technical specifications” paragraph below).

The function divides the heat level between cooking zones and

activates when the total electricity loading of the cooking zones

exceeds 3700 W. The function decreases the heat level to the

other cooking zones. The heat setting display of the reduced

zones changes between two levels.

Technical specifications

In acc. with regulation (EU) No. 66/2014

product dimensions: 29x52 cm

Cooking

zone

Cooking zone

dimensions

(cm)

Minimum pot

dimensions

(cm)

Output

(watt) 230V

EC - Energy

Consumption

(Wh/kg)

a, b 20x18

Ø 14,5

normal

booster

2100

3700

171

a+b 20x37

23x14,5

normal

booster

2100

3700

171

type of hob: built-in

heating technology: induction

max.

power

3700

171

using the cooktop

ENGLISH

troubleshooting

Problem Possible cause Remedy

You cannot activate or operate

the appliance.

The appliance is not

connected to an electrical

supply or it is connected

incorrectly.

Check if the appliance is correctly

connected to the electrical supply.

Refer to “electrical connection”

chapter.

The fuse is released. Make sure that the fuse is the cause

of the malfunction.

If the fuse releases again and again,

contact a qualiﬁed electrician.

it’s been more than 10

seconds from the switching

on of the appliance.

Activate the appliance again and

set the heat setting in less than 10

seconds.

You touched 2 or more

sensor keys at the same

time.

Touch only one sensor key.

Pause function operates. Refer to “Using the cooktop”

chapter.

There is water or fat stains

on the control panel.

Clean the control panel.

The hob deactivates. You put something on the

sensor key ON-OFF.

Remove the object from the sensor

key.

Residual heat indicator does not

come on.

The zone is not hot because

it operated only for a short

time.

If the zone operated sufﬁciently

long to be hot contact an Authorised

Service Centre.

Automatic Warm Up function

does not operate.

The zone is hot. Let the zone become sufﬁciently

cool.

The highest heat setting is

set.

The highest heat setting has the

same power as the function.

The heat setting changes

between two levels.

Power management

function operates.

Refer to “Using the cooktop”

chapter.

The sensor keys become hot. The cookware is too large

or you put it too near to the

controls.

Put large cookware on the rear

zones if possible.

a 4

comes on.

Automatic Switch Off

operates.

Deactivate the appliance and

activate it again.

comes on.

The Child Lock function

operates.

Refer to “Using the cooktop”

chapter.

comes on.

Water or cooking utensils

above the control panel.

Remove the objects from the control

panel.

uguale per tutti i BIU

ENGLISH

0 4

comes on.

There is no cookware on

the zone.

Put cookware on the zone.

The cookware is incorrect. Use the correct cookware. Refer to

“Induction Cooking” chapter.

The dimension of the

bottom of the cookware is

too small for the zone.

Use cookware with correct

dimensions. Refer to “Induction

Cooking” chapter.

The cookware does not

cover the cooking zone.

Cover the cooking zone fully.

e 4

and a number come on.

There is an error in the

appliance.

Disconnect the appliance from

the electrical supply for some

time. Disconnect the fuse from

the electrical system of the house.

Connect it again. If comes on again,

contact an Authorised Service

Centre.

comes on.

The induction coils are

overheated.

Allow the appliance to cool down.

e21

e03

comes on.

The appliance is

overheated. The cooling

fan might be blocked.

Allow the appliance to cool down.

Check if objects block the cooling

fan. If comes on again, contact an

Authorised Service Centre.

e03

comes on.

Incorrect data

conﬁguration.

New conﬁguration needed. Contact

an Authorised Service Centre.

e03

comes on.

None or faulty

communication between

control panel and induction

coils.

Ensure that connection cable is

plugged on correctly and functional.

comes on.

Control Panel is wrongly

connected.

Connect to correct mains voltage.

e03

comes on.

An internal component

of the appliance needs

replacing.

Contact an Authorised Service

Centre.

If you cannot find a solution to the problem yourself, contact your dealer or

an Authorised Service Centre. Give the data from the rating plate.

troubleshooting

ENGLISH

cleaning and care

uguale per tutti i piani

Important information

• Clean regularly the appliance to prevent the deterioration of the surface

material.

• Deactivate the appliance and let it cool down before you clean it.

• Disconnect the appliance from the electrical supply before maintenance.

• Do not use water spray and steam to clean the appliance.

• Clean the appliance with a moist soft cloth. Only use neutral detergents.

• Do not use abrasive products, abrasive cleaning pads, solvents or metal

objects.

General information

• Clean the hob after each use.

• Always use cookware with clean bottom.

• Scratches or dark stains on the surface have no effect on how the hob

operates.

• Use a special cleaner applicable for the surface of the hob.

• Use a special scraper for the glass.

Cleaning the cooktop

• Remove immediately: melted plastic,

plastic foil, and food with sugar.

If not, the dirt can cause damage to the

cooktop. Put the special scraper on

the glass surface at an acute angle and

move the blade on the surface.

• Remove when the hob is sufficiently

cool: limescale rings, water rings, fat

stains, shiny metallic discoloration.

Clean the cooktop with a moist cloth

and non-abrasive detergent. After

cleaning, wipe the cooktop dry with a

soft cloth.

ENGLISH

protecting the environment

Disposal of the packing material

The cardboard box and packing materials protect the appliance during shipping.

They have been designed to be biodegradable and recyclable.

Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out

of the reach of children. Danger of suffocation!

Disposal of your old appliance

The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment

(WEEE), requires that old household electrical appliances must not be disposed of

in the normal unsorted municipal waste stream. Old appliances must be collected

separately in order to optimise the recovery and recycling of the materials they

contain and reduce the impact on human health and the environment.

The crossed-out dustbin symbol on the product reminds you of your

obligation regarding separated waste collection. Consumers should

contact their local public service or their local dealer for more information

on the correct disposal of exhausted household appliances.

Energy-saving advice

• Always place a ﬁtting lid on cookware. Cooking with an uncovered pan will result

in a four-fold increase in energy use. Use a glass lid to provide visibility and avoid

having to lift the lid.

• Use cookware equipped with a solid, ﬂat bottom. Curved pan bases increase

energy consumption.

• The diameter of the pan base must match the size of the element. If not, energy

may be wasted. Note: The manufacturer normally indicates the pan’s upper

diameter. This is normally greater than the diameter of the pan’s base.

• Choose cookware of a size suited to the amount of food you are going to cook.

A large pan that is only half full will use a lot of energy.

• Use a small amount of water when cooking. This saves energy, and vegetables

retain a larger percentage of their vitamins and minerals.

• Select a lower power level.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR

EVENTUAL DAMAGES CAUSED BY BREAKING THE ABOVE WARNINGS.

THE WARRANTY IS NOT VALID IN THE CASE OF DAMAGE CAUSED BY

FAILURE TO COMPLY WITH THE ABOVE WARNINGS.

uguale per tutti i piani

ENGLISH

i punti in azzurro vengono dai nostri vecchi

manuali es. BTO632

uguale per tutti i BIU

PART 2 - Installer Guide

installation

Installing the cooktop

1. Create the cut-out on the worktop (see paragraph ‘‘Worktop cut-out’’).

CAUTION!

Excessive Weight Hazard

Use two or more people to move and install cooktop.

Failure to do so can result in back or other injury.

2. Using 2 or more people, place the cooktop upside down on a covered surface

and predispose sealing material along the whole perimeter of the cooktop.

3. Place the cooktop centrally in the cut-

out and feed the mains connection cable

down through the cut-out. When doing

this, make sure that the seal under the

cooktop sits ﬂush with the worktop on

all sides. This is important to ensure

an effective seal all round. Do not use

sealant (e.g. silicone). If the seal does

not meet the worktop correctly on the

corners the corner radius can be carefully

scribed to suit.

2 mm

La pagina sta caricando ...

Foster 7341/645 Use And Installation Manual

Marca: Foster

Modello: 7341/645

Categoria: Piani cottura

Tipo: Use And Installation Manual

Scarica il pdf

rapporto

in altre lingue

English: Foster 7341/645
français: Foster 7341/645
español: Foster 7341/645
Deutsch: Foster 7341/645

Documenti correlati

Foster 7322/300 Use And Installation Manual

Foster 7341/645 Use And Installation Manual

Foster 7341/645 Use And Installation Manual

in altre lingue

Documenti correlati

Altri documenti