Hitachi RAK-25PPA Manuale utente

– 1 –

ENGLISH

– 1 –

ENGLISH

SPLIT TYPE AIR CONDITIONER

MODEL

INDOOR UNIT/OUTDOOR UNIT

INDOOR UNIT

RAK-18PPA

RAK-25PPA

RAK-35PPA

OUTDOOR UNIT

Instruction manual Page 1~15

To obtain the best performance and ensure years of

trouble free use, please read this instruction manual

completely.

RAC-18WPA

RAC-25WPA

RAC-35WPA

RAK-18PPA/RAC-18WPA

RAK-35PPA/RAC-35WPA

RAK-25PPA/RAC-25WPA

Instruction manual Page 1~36

To obtain the best performance and ensure years of

trouble free use, please read this instruction manual

completely.

Bedlenungsanleitung Seite 37~72

Bitte lesen Sie diese Bedienungsanleitung aufmerksam

durch, um durch richtige Bedienung jahrelangen und

störungsfreien Betrieb zu gewährleisten.

Mode d’emploi Page 73~108

Des performances optimales et un fonctionnement à

long terme seront assurés en appliquant les présentes

instructions après avoir entièrement lu ce mode

d’emploi.

Manuale di istruzioni Pag. 109~144

Per garantire la migliore prestazione e la più lunga

durataleggere attentamente e al completo le seguanti

istruzioni.

Manual de instrucciones Página 145~180

Para obtener el mejor funcionamiento y asegurar años

de uso libre de problemas, lea cuidadosamente este

manual de instrucciones.

Manual de instruções Página 181~216

A m de obter um bom funcionamento e de garantir

uma utilização sem falhas durante muitos anos, é

favor ler este manual de instruções completamente.

Οδηγίες χρήσης ™ÂÏ›‰· 217~252

°È· ÙËÓ Î·Ï‡ÙÂÚË ·ﬁ‰ÔÛË ÙÔ˘ ÎÏÈÌ·ÙÈÛÙÈÎÔ‡ Î·È ÁÈ·

ÙËÓ Ì·ÎÚÔÚﬁıÂÛÌË ¯Ú‹ÛË ÙÔ˘ ¯ˆÚ›˜ ÚÔ‚Ï‹Ì·Ù·,

‰È·‚¿ÛÙÂ ÚÔÛÂÎÙÈÎ¿ ·˘Ù¤˜ ÙÈ˜ Ô‰ËÁ›Â˜ ¯Ú‹ÛË˜.

– 2 –

SAFETY PRECAUTION

• Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.

• Pay special attention to signs of “

Warning” and “ Caution”. The “Warning” section contains

matters which, if not observed strictly, may cause death or serious injury. The “Caution” section

contains matters which may result in serious consequences if not observed properly. Please observe

all instructions strictly to ensure safety.

• The signs indicate the following meanings. (The following are examples of signs.)

• Please keep this manual after reading.

This sign in the figure indicates prohibition. Indicates the instructions that must be followed.

WARNING

CAUTION

• Do not reconstruct the unit.

Water leakage, fault, short circuit or fire may occur if you reconstruct the unit by

yourself.

• Please ask your sales agent or qualified technician for the installation of your

unit.

Water leakage, short circuit or fire may occur if you install the unit by yourself.

• Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor, or the

earth line of telephone. Improper installation of earth line may cause electric

shock.

• Be sure to use the specified piping set for R410A. Otherwise, this may result in

broken copper pipes or faults.

• A circuit breaker should be installed depending on the mounting site of the unit.

Without a circuit breaker, the danger of electric shock exists.

• Do not install the unit near a location where there is flammable gas.

The outdoor unit may catch fire if flammable gas leaks around it. Piping shall be

suitable supported with a maximum spacing of 1m between the supports.

• Please ensure smooth flow of water when installing the drain hose. If any failure

is found in the drain path, water drops from the indoor and outdoor units, causing

wet household effects.

• Make sure that a single phase 230V power source is used.

The use of other power sources may cause electrical components to overheat

and lead to fire.

PROHIBITION

CONNECT EARTH LINE

PROHIBITION

• Should abnormal situation arise (like burning smell), please stop operating the

unit and remove plug from the socket or turn off the circuit breaker. Contact your

agent. Fault, short circuit or fire may occur if you continue to operate the unit

under abnormal situation.

• Please contact your agent for maintenance.

Improper self maintenance may cause electric shock and fire.

• Please contact your agent if you need to remove and reinstall the unit.

Electric shock or fire may occur if you remove and reinstall the unit yourself improperly.

WARNING

PRECAUTIONS DURING INSTALLATION

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

“OFF”

PROHIBITION

• Avoid an extended period of direct air flow for your health.

• Do not connect the power calbe with an extension cable or do not plug too many

leads of the other electric appliance into the socket where this cable is plugged.

In addition, wire the cable with some allowances to prevent the cable from stretching.

Not doing so will cause an electrical shock, heat generation or fire.

PROHIBITION

• Do not put objects like thin rods into the panel of blower and suction side

because the high-speed fan inside may cause danger.

• Do not bundle the power cable, pull it, put something on it, heat it, process it, or

put it between things. Breakage of the power cable may result.

Use of a damaged cable may cause an electrical shock or a fire.

PROHIBITION

– 3 –

ENGLISH

– 3 –

ENGLISH

WARNING

PRECAUTIONS DURING OPERATION

• Do not use any conductor as fuse wire, this could cause fatal accident.

PROHIBITION

• During thunder storm, disconnect the plug top or turn off the circuit breaker.

• Spray cans and other combustibles should not be located within a meter of the air

outlets of both indoor and outdoor units.

As a spray can’s internal pressure can be increased by hot air, a rupture may result.

“OFF”

CAUTION

PROHIBITION

• The product shall be operated under the manufacturer specification and not for

any other intended use.

PROHIBITION

DON’T WET

• Do not attempt to operate the unit with wet hands, this could cause fatal accident.

STRICTLY OBSERVE

PRECAUTIONS

PROHIBITION

• When operating the unit with burning equipments, regularly ventilate

the room to avoid oxygen insufficiency.

• Do not direct the cool air coming out from the air-conditioner panel to

face household heating apparatus as this may affect the working of

apparatus such as the electric kettle, oven etc.

• Do not wash the unit with water or place a water container such as a

vase on the indoor unit.

Electrical leakage could be present and cause electric shock.

• Please ensure that outdoor mounting frame is always stable, firm and

without defect. If not, the outdoor unit may collapse and cause danger.

• Do not place plants or animals directly under the air flow as it is bad for the plants or

animals.

• Do not climb on the outdoor unit or put objects on it.

PROHIBITION

DON’T TOUCH

• When operating the unit with the door and windows opened, (the room humidity

is always above 80%) and with the air deflector facing down or moving automati-

cally for a long period of time, water will condense on the air deflector and drips

down occasionally. This will wet your furniture. Therefore, do not operate under

such condition for a long time.

• If the amount of heat in the room is above the cooling or heating capability of the

unit (for example: more people entering the room, using heating equipments and

etc.), the preset room temperature cannot be achieved.

• This appliance especially indoor unit cleaning must be performed by authorized

personnel only. Consult your sales agent.

Using a commercially available detergent or similar can damage the plastic parts

or clog the drain pipe, causing water to drip with potential electric shock hazard.

• Do not touch the air outlet, bottom surface and aluminum fin of the outdoor

unit.

You may get hurt.

• Do not touch the refrigerant pipe and connecting valve.

Burns may result.

• This appliance is not intended for use by young children or infirm persons unless they have been

adequately supervised by a responsible person to ensure that they can use this appliance safely.

• Young children should be supervised to ensure that they do not play with the appliance.

– 4 –

780 280 218

700 505 258

750 548 288

RAK-18PPA , RAK-25PPA , RAK-35PPA

– 4 –

RAC-18WPA , RAC-25WPA

RAC-35WPA

Drain hose

Drains the dehumidified water from the indoor unit to the

outdoor during “cooling” or “dehumidifying” operation.

Piping and Wiring

Air inlets (Rear and left sides)

Air filter

To prevent dust from coming into the indoor unit.

(Refer page )

Front panel

Indoor unit indicators

Light indicator showing the operating condition.

(Refer page 5)

Horizontal deflector Vertical deflector

(Air Outlet)

Remote controller

Send out operation signal to the indoor unit. So as

to operate the whole unit.

(Refer page 6)

NAMES AND FUNCTIONS OF EACH PART

INDOOR UNIT

OUTDOOR UNIT

Air outlet

When “heating” operation is

performed, cool air blows and

when “cooling” or “dehumidifying”

operation is performed, warm air

blows.

Drain port

(Bottom)

Earth terminal

(Lower section of the side)

Air outlet

When “heating” operation is

performed, cool air blows and

when “cooling” or “dehumidifying”

operation is performed, warm air

blows.

Drain hose

Drains the dehumidified water from the indoor unit to the

outdoor during “cooling” or “dehumidifying” operation.

Piping and Wiring

Air inlets (Rear and left sides)

MODEL NAME AND DIMENSIONS

MODEL WIDTH (mm) HEIGHT (mm) DEPTH (mm)

Drain port

(Bottom)

Earth terminal

(Lower section of the side)

About the outdoor unit:

• When “Stop” is selected during operation

of the indoor unit, the fan of the outdoor

unit continues turning for 10 to 60

seconds to cool the electric parts down.

• In heating operation, condensate or

water due to defrosting will flow.

Do not cover the drain port of the outdoor

unit because such water may freeze in

the chilly area.

• When the outdoor unit is hung on the

ceiling, install the bush and drain pipe

on the drain port and drain water.

RAC-18WPA

RAC-25WPA

RAC-35WPA

31

(Refer page )

31

– 5 –

ENGLISH

– 5 –

HSILGNE

NAMES AND FUNCTIONS OF EACH PART

INDOOR UNIT INDICATIONS

TIMER LAMP (Orange)

This lamp lights when the

timer is working.

OPERATION LAMP (Yellow)

This lamp lights during operation.

The OPERATION LAMP flashes

in the following cases during

heating.

(1) During preheating

For about 2-3 minutes after

starting up.

(2) During defrosting

Defrosting will be performed

about once an hour when frost

forms on the heat exchanger

of the outdoor unit, for 5-10

minutes each time.

TEMPORARY SWITCH

Use this switch to start and stop when the remote

controller does not work.

This temporary operation will be at the most

recent

setting made. (The unit will immediately go into

automatic operation once power is switched on.)

CAUTION

Turn off the circuit breaker or pull out

the power plug if the unit is not be

operated for a long period.

If the power stays on and the unit is not operated, power is slightly consumed in the control circuit.

The power is saved by turning off the power switch (or the circuit breaker when the power is supplied

from the outdoor unit).

Attaching the Wasabi-Nano Titanium Air Cleaning

s Attach the

to the C-case by gently compress its both sides

and release after insertion into filter frame.

s The cooling capacity is slightly weakened and

the cooling speed becomes slower when the

are used.

.

s

and reusable up to 20 times by using vacuum

cleaner or water rinse under running tap water.

When you want to renew it, please ask your sales

agent. Optional air cleansing and deodorizing

filters.

Air Filter

Claw

Filter Frame

Mesh (Accessories) to the filter frame.

Wasabi-Nano Titanium Air Cleaning Mesh

are washable

Wasabi-Nano Titanium Air Cleaning Mesh

C-case

– 6 –

PREPARATION BEFORE OPERATION

– 6 –

HSILGNE

1. Slide the cover to take it off.

2.

Install two dry batteries AAA.LR03 (alkaline).

The direction of the batteries should match

the

marks in the case.

1. Choose a place from where the signals can reach the unit.

2. Fix the remote controller holder to a wall, a pillar or similar

location with the provided screws.

3.

Place the remote controller in the remote controller holder.

Remote controller

Screws

Remote controller holder

■ To install the batteries

3. Replace the cover at its original position.

■ To  fix the remote controller holder to the wall

NOTE

Notes on batteries

● When replacing the batteries, use batteries of the same

type, and replace both old batteries together

.

● When the system is not used for a long time, take the

batteries out.

● The batteries will last for approximately 1 year. However, if

the remote controller display begins to fade and degradation

of reception performance occurs within a year

, replace both

batteries with new size AAA.LR03 (alkaline).

● The attached batteries are provided for the initial use of

the system.

The usable period of the batteries may be short depending

on the manufactured date of the air conditioner.

Notes on the remote controller

● Never expose the remote controller to direct sunlight.

● Dust on the signal transmitter or receiver will reduce the

sensitivity

. Wipe off dust with soft cloth.

● Signal communication may be disabled if an electronic-

starter-type 

uorescent lamp (such as inverter-type lamps)

is in the room. Consult the shop if that is the case.

● If the remote controller signals happen to operate another

appliance,

move that appliance to somewhere else, o

r

consult the service shop.

● When the remote controller is not in use, please close the

slide cover to prevent failure.

– 7 –

ENGLISH

– 7 –

HSILGNE

PREPARATION BEFORE OPERATION

■ To set calendar and clock

1. Press (RESET) button when first time setting.

"Year" blinks.

2. Press

(TIME) button to set the current year.

3. Press

(CLOCK) button. Next, "Day" and

"Month" blink.

4. Press

(TIME) button to set the current day and

month.

5. Press

(CLOCK) button. Next, "CLOCK" blinks.

6. Press

(TIME) button to set the clock to the current

time.

7. Press

(CLOCK) button.

Calendar and clock are set.

To modify the calendar and clock, press

(CLOCK)

button.

Then follow steps 1 to 7.

Calendar and clock shall be set again after changing

batteries.

After changing the batteries,

1. Press

(RESET) button.

2. Direct remote control towards indoor unit and press

(INFO) button.

3. The calendar and clock from indoor unit will be transmitted.

■ Calendar and clock will not be transmitted from indoor

unit when the following occurs:

● When there is a power failure.

● When breaker is OFF by user (unit is not in STANDBY

MODE).

NOTE

Note on setting the calendar and clock.

● If the calendar and clock are not set, the ON-timer, OFF-timer and Weekly Timer cannot be set.

● If the calendar and clock are not set correctly, the ON-timer, OFF-timer and Weekly Timer will not

operate correctly.

● When the ON-timer, OFF-timer and Weekly Timer are set, the calendar and clock cannot be changed. If

need to change the calendar and clock, ON-timer, OFF-timer and Weekly Timer need to be cancelled.

– 8 –

HSILGNE

NAMES AND FUNCTIONS OF REMOTE CONTROLLER

REMOTE CONTROLLER

● This controls the operation of the indoor unit. The range of control is about 7 meters. If indoor lighting is

controlled electronically, the range of controller may be shorter.

This unit can be fixed on a wall using the fixture provided. Before fixing it, make sure the indoor unit can

be controlled from the remote controller.

● Handle the remote controller with care. Dropping it or getting it wet may compromise its signal transmission

capability.

● After new batteries are inserted into the remote controller, the unit will initially require approximately 10

seconds to respond to commands and operate.

● When remote controller is not in use for about 3 minutes during OFF condition, indicated by on the

display, the LCD will turn off.

● During clock setting, the LCD will turn off about 10 minutes later if the remote controller is not in use.

● When pressing any button, the LCD will turn on.

● The LCD will not turn off during TIMER setting.

Signal Transmitting/Receiving

Window

Point this window towards the

indoor unit when controlling it.

Sensor

A temperature sensor inside the

remote controller senses ambient

temperature around the remote-

controller.

Display

ROOM TEMPERATURE setting Buttons

Press these buttons to set the room

temperature.

Press the [

] button to raise the room

temperature.

Press the [

] button to lower the room

temperature.

Keep pressing and the value will change

more quickly.

ECO Button

Use this button to set the ECO

START/STOP button

Press this button to start

operation. Press it again to stop

operation.

Transmission sign

The transmission sign lights up

when a signal is sent.

FAN SPEED selector Button

This determines the fan speed.

Every time you press this button

the ange from

(AUTO) (HIG H)

(MED) (LOW)

(SILENT) (This button allows

optimal or preferred

fan speed for each operation mode).

➔

airflow rate will ch

selection of

This indicates the room temperature

selected, current time, timer status,

function and airflow rate selected.

mode.( p.18)

– 9 –

HSILGNE

MODE SELECTOR

AUTO

HEAT

DEHUMIDIFY

COOL

FAN

FAN SPEED

AUTO

SILENT

LOW

MED

HI

START / STOP

ECO

Precautions for Use

●

Do not put the remote controller in the following places.

●

Under direct sunlight.

●

In the vicinity of a heater.

●

Handle the remote controller carefully. Do not drop it on the floor, and protect it from water.

●

Once the outdoor unit stops, it will not restart for about 3 minutes (unless you turn the power switch

off and on or unplug the power cord and plug it in again).

This is to protect the device and does not indicate a failure.

●

If you press the MODE selector button during operation, the device may stop for about 3 minutes for

protection.

POWERFUL Button

Use this button to set the

POWERFUL mode.

INFORMATION Button

ONE TOUCH CLEAN Button

ON / OFF TIMER setting Buttons

MODE selector Button

Use this button to select the

operating mode. Every time you

press this button, the mode will

change from

(AUTO)

(HEAT)

(DEHUMIDIFY)

(COOL) and

(FAN)

cyclically.

SILENT Button

Use this button to set the SILENT

mode.

AUTO SWING (Vertical) Button

Controls the angle of the

horizontal air deflector.

WEEKLY TIMER setting Buttons

LEAVE HOME Button

NAMES AND FUNCTIONS OF REMOTE CONTROLLER

SLEEP TIMER Button

Use this button to set the sleep

timer.

FAN

POWERFUL

SILENT

INFO

SLEEP TIMER

AUTO SWING (VERTICAL)

LEAVE HOME

CLEAN

DAY

PROGRAM NO.

ON / OFF TIMER

TIME

OK

DELETE

COPY / PASTE

CANCEL

SEND

CLOCK

( p.16)

( p.30 )

( p.20 )

( p.19)

( p.21)

( p.22)

( p.17)

( p.24)

( p.15)

– 9 –

ENGLISH

– 9 –

HSILGNE

MODE SELECTOR

AUTO

HEAT

DEHUMIDIFY

COOL

FAN

FAN SPEED

AUTO

SILENT

LOW

MED

HI

START / STOP

ECO

Precautions for Use

●

Do not put the remote controller in the following places.

●

Under direct sunlight.

●

In the vicinity of a heater.

●

Handle the remote controller carefully. Do not drop it on the floor, and protect it from water.

●

Once the outdoor unit stops, it will not restart for about 3 minutes (unless you turn the power switch

off and on or unplug the power cord and plug it in again).

This is to protect the device and does not indicate a failure.

●

If you press the MODE selector button during operation, the device may stop for about 3 minutes for

protection.

POWERFUL Button

Use this button to set the

POWERFUL mode.

INFORMATION Button

ONE TOUCH CLEAN Button

ON / OFF TIMER setting Buttons

MODE selector Button

Use this button to select the

operating mode. Every time you

press this button, the mode will

change from

(AUTO)

(HEAT)

(DEHUMIDIFY)

(COOL) and (FAN)

cyclically.

SILENT Button

Use this button to set the SILENT

mode.

AUTO SWING (Vertical) Button

Controls the angle of the

horizontal air deflector.

WEEKLY TIMER setting Buttons

LEAVE HOME Button

NAMES AND FUNCTIONS OF REMOTE CONTROLLER

SLEEP TIMER Button

Use this button to set the sleep

timer.

FAN

POWERFUL

SILENT

INFO

SLEEP TIMER

AUTO SWING (VERTICAL)

LEAVE HOME

CLEAN

DAY

PROGRAM NO.

ON / OFF TIMER

TIME

OK

DELETE

COPY / PASTE

CANCEL

SEND

CLOCK

( p.16)

( p.30 )

( p.20 )

( p.19)

( p.21)

( p.22)

( p.17)

( p.24)

( p.15)

– 10 –

HSILGNE

AUTOMATIC OPERATION

The device will automatically determine the mode of operation, HEAT or COOL depending on the current

room temperature. The selected mode of operation will change when the room temperature varies.

However, the mode of operation will not change when indoor unit is connected to multi type outdoor unit.

VARIOUS FUNCTIONS

■ Auto Restart Control

● If there is a power failure, operation will be automatically restarted when the power is resumed with previous operation

mode and airflow direction.

(As the operation is not stopped by remote controller.)

● If you intend not to continue the operation when the power is resumed, switch off the power supply.

When you switch on the circuit breaker, the operation will be automatically restarted with previous operation

mode

and air flow

direction.

Note: 1. If you do not require Auto Restart Control, please consult your sales agent.

2. Auto Restart Control is not available when Timer or Sleep Timer mode is set.

Press the MODE selector button so that the display indicates the

(AUTO) mode of operation.

● When AUTO has been selected, the device will automatically

determine the mode of operation, HEAT or COOL depending on

the current

room temperature. However the mode of operation will

not change when indoor unit is connected to multi type

outdoor

unit.

● If the mode automatically selected by the unit is not satisfactory

,

manually change the mode setting (HEAT, DEHUMIDIFY, COOL

or FAN).

Press the (FAN SPEED) button to select AUTO, HI, MED, LOW or

SILENT.

Press the

(START/STOP) button.

Operation starts with a beep.

Press the button again to stop operation.

Set the desired room temperature with the TEMPERATURE buttons

(the display indicates the setting).

The temperature setting and the actual room temperature may vary

depending on conditions.

START

STOP

1

3

2

Set the desired FAN SPEED with the (FAN SPEED) button (the

display indicates the setting).

(AUTO)

(HIGH)

(MED)

(LOW)

(SILENT)

■ As the settings are stored in the memory the remote controller, you

(START/STOP) button next time.only have to press the

of

– 11 –

ENGLISH

– 11 –

HSILGNE

HEATING OPERATION

● Use the device for heating when the outdoor temperature is under 21°C.

When it is too warm (over 21°C), the heating function may not work in order to protect the device.

●

Press the MODE selector button so that the display indicates

(HEAT).

Set the desired FAN SPEED with the (FAN SPEED) button

(the display indicates the setting).

Set the desired room temperature with the TEMPERATURE buttons

(the display indicates the setting).

The temperature setting and the actual room temperature may

vary depending on conditions.

Press the

(START/STOP) button. Heating operation starts with

a beep. Press the button again to stop operation.

■

■ During AUTO fan, the fan speed automatically changes as below:

● When the difference between room temperature and setting temperature

is large, fan starts to run at HI speed.

● After room temperature reaches the preset temperature, fan speed

will be changed to lower speed to obtain optimum room temperature

condition for natural healthy heating.

START

STOP

■ Defrosting

Defrosting will be performed about once an hour when frost forms on the heat exchange of the outdoor unit,

for 5~10 minutes each time.

During defrosting operation, the operation lamp blinks in a cycle of 3 seconds on and 0.5 second off.

The maximum time for defrosting is 20 minutes.

(If the piping length used is longer than usual, frost is likely to form.)

1

2

3

In order to maintain reliability of the device, please use this device when outdoor temperature is above -15°C.

(AUTO)

(HIGH)

(MED)

(LOW)

(SILENT)

■ As the settings are stored in the memory of the remote controller, you only

have to press the (START/STOP) button next time.

However, if the indoor unit is connected to multi type outdoor unit, the maximum time for defrosting is 15 minutes.

– 12 –

HSILGNE

DEHUMIDIFYING OPERATION

■ Dehumidifying Function

● When the room temperature is higher than the temperature setting: The device will dehumidify the

room, reducing the room temperature to the preset level.

When the room temperature is lower than the temperature setting: Dehumidifying will be performed at

the temperature setting slightly lower than the current room temperature, regardless of the temperature

setting.

● The preset room temperature may not be reached depending on the number of people present in the

room or other room conditions.

Set the desired room temperature with the ROOM

TEMPERATURE setting buttons (the display indicates the

setting).

The range of 20-26°C is recommended as the room

temperature for dehumidifying.

Press the (START/STOP) button. Dehumidifying operation

starts with a beep. Press the button again to stop operation.

■ As the settings are stored in the memory of the remote controller, you

(START/STOP) button next time.

START

STOP

Press the MODE selector button so that the display

indicates

(DEHUMIDIFY).

The fan speed is set at LOW.

Press

(FAN SPEED) button to select SILENT or LOW fan

speed.

Use the device for dehumidifying when the room temperature is over 16°C.

When it is under 15°C, the dehumidifying function will not work.

1

2

only have to press the

– 13 –

HSILGNE

COOLING OPERATION

Use the device for cooling when the outdoor temperature is -10~ 43°C.

If indoors humidity is very high (80%), some dew may form on the air outlet grille of the indoor unit.

Press the MODE selector button so that the display indicates

(COOL).

Set the desired FAN SPEED with the

(FAN SPEED) button (the

display indicates the setting).

Set the desired room temperature with the TEMPERATURE buttons

(the display indicates the setting).

The temperature setting and the actual room temperature may vary

depending on conditions.

Press the

(START/STOP) button. Cooling operation starts with a

beep. Press the button again to stop operation. The cooling function

does not start if the temperature setting is higher than the current

room temperature (even though the (OPERATION) lamp lights).

The cooling function will start as soon as user set the temperature

below the current room temperature.

■

As the settings are stored in the memory of the remote controller, you only

have to press the

(START/STOP) button next time.

■ During AUTO fan, the fan speed automatically changes as below:

● When the difference between room temperature and setting tem-

perature is large, fan starts to run at HI speed.

● After room temperature reaches the preset temperature, fan speed

will be changed to lower speed to obtain optimum room temperature

condition for natural healthy cooling.

START

STOP

1

3

(AUTO)

(HIGH)

(MED)

(LOW)

(SILENT)

2

– 13 –

ENGLISH

– 13 –

HSILGNE

COOLING OPERATION

Use the device for cooling when the outdoor temperature is -10~ 43°C.

If indoors humidity is very high (80%), some dew may form on the air outlet grille of the indoor unit.

Press the MODE selector button so that the display indicates

(COOL).

Set the desired FAN SPEED with the

(FAN SPEED) button (the

display indicates the setting).

Set the desired room temperature with the TEMPERATURE buttons

(the display indicates the setting).

The temperature setting and the actual room temperature may vary

depending on conditions.

Press the

(START/STOP) button. Cooling operation starts with a

beep. Press the button again to stop operation. The cooling function

does not start if the temperature setting is higher than the current

room temperature (even though the (OPERATION) lamp lights).

The cooling function will start as soon as user set the temperature

below the current room temperature.

■

As the settings are stored in the memory of the remote controller, you only

have to press the

(START/STOP) button next time.

■ During AUTO fan, the fan speed automatically changes as below:

● When the difference between room temperature and setting tem-

perature is large, fan starts to run at HI speed.

● After room temperature reaches the preset temperature, fan speed

will be changed to lower speed to obtain optimum room temperature

condition for natural healthy cooling.

START

STOP

1

3

(AUTO)

(HIGH)

(MED)

(LOW)

(SILENT)

2

– 14 –

HSILGNE

FAN OPERATION

User can use the device simply as an air circulator.

START

STOP

1

2

Press the MODE selector so that the display indicates

(FAN).

Press the

(START/STOP) button. Fan operation starts with

a beep. Press the button again to stop operation.

Set the desired FAN SPEED with the (FAN SPEED) button

(the display indicates the setting).

(AUTO)

(HIGH)

(MED)

(LOW)

(SILENT)

– 15 –

ENGLISH

Vertical

about 10°

about 40°

When cooling,

dehumidifying

When heating

about 10°

about 45°

HSILGNE

– 15 –

Minimum Maximum Minimum Maximum

Indoor Dry bulb °C 21 32 20 27

Wet bulb °C 15 23 12 19

Outdoor Dry bulb °C 21 43 2 21

Wet bulb °C 15 26 1 15

Note

gnitaeHgnilooC

Avoid to use the room air conditioner for cooling operation when the outside temperature is below

-10°C (14°F).

The recommended maximum and minimum operating temperatures of the hot and cold sides

should be as below:

AUTO SWING OPERATION

■ To start Vertical Auto Swing

■ To cancel Vertical Auto Swing

NOTE

●

During cooling and dehumidifying operation, do not keep

the deflectors swinging or in the lower position (in the case

of vertical auto swing) for a long time. It may cause dew

condensation on the deflectors.

Press (AUTO SWING (VERTICAL)) button. The

deflector(s) will start to swing up and down.

 is displayed on the LCD.

Press (AUTO SWING (VERTICAL)) button again. The

deflector(s) will stop in the current position.

 disappeared from the LCD.

●

– 16 –

HSILGNE

POWERFUL OPERATION

● By pressing (POWERFUL) button during AUTO, HEATING, DEHUMIDIFYING, COOLING or FAN

operation, the air conditioner performs an the maximuum power.

● During POWERFUL operation, cooler or warmer air will be blown out from indoor unit for COOLING of

HEATING operation respectively.

■ To start POWERFUL operation

■ To cancel POWERFUL operation

1

NOTE

● When SLEEP mode, ECO mode, SILENT mode or LEAVE HOME mode is selected, POWERFUL

operation is cancelled.

● During POWERFUL operation, capacity of the air conditioner will not increase

– if the air conditioner is already running at maximum capacity.

–

just before defrost operation (when the air conditioner is running in HEATING operation).

● After auto restart, POWERFUL operation is cancelled and previous operation shall start.

Press (POWERFUL) button during operation.

●

“

” is displayed on the LCD.

POWERFUL operation ends in 20 minutes. Then the system

automatically operates with the previous settings used before

POWERFUL operation.

Press

(POWERFUL) button again.

POWERFUL operation stops.

“

” disappears from the LCD.

●

Press (START/ STOP) button.Or

●

– 17 –

ENGLISH

– 17 –

HSILGNE

SILENT OPERATION

● By pressing (SILENT) button during AUTO, HEATING, DEHUMIDIFYING, COOLING or FAN

operation, the fan speed will change to ultra slow.

■ To start SILENT operation

■ To cancel SILENT operation

Press (SILENT) button during operation.

“

” is displayed on the LCD. Fan speed will be ultra

slow.

● Press (START/STOP) button. Or

● Press (SILENT) button again or (FAN SPEED)

button.

Fan speed will return to previous fan speed before SILENT

operation starts.

SILENT operation stops.

“

” disappears from the LCD.

1

NOTE

● When POWERFUL operation is selected, SILENT operation is cancelled. Fan speed will return to

previous fan speed before SILENT operation.

● After auto restart, SILENT operation is cancelled. Fan speed will return to previous

fan speed before SILENT operation.

● During any operation with fan speed (SILENT), if press (SILENT) button, fan speed will

not change.

●

– 18 –

HSILGNE

ECO OPERATION

● By pressing the (ECO) button during AUTO, HEATING,

DEHUMIDIFYING or COOLING operation, the air conditioner

performs the "ECO" operation.

1

■ To start ECO operation

■ To cancel ECO operation

Press (ECO) button during operation.

“

” is displayed on the LCD.

Energy saving operation will start by changing the set

temperature higher or lower automatically and reducing operation

power consumption. This function may vary based on the

●

Press (START/STOP) button.Or

●

Press (ECO) button again.

“

” disappears from the LCD.

NOTE

●

ECO function will not be effective when power consumption is low.

●

By pressing (POWERFUL) button, ECO operation is cancelled.

●

After auto restart, ECO operation is cancelled and previous operation mode shall start.

●

For multi model connections, energy saving operation shall only start by changing set temperature higher

connected outdoor unit.

o

r lower automatically. However, effectiveness of ECO depends on operation conditions.

ECO operation is an energy saving function by changing set temperature automatically and by limiting the

ma x imum power consumption value.

●

– 19 –

HSILGNE

LEAVE HOME(LH) OPERATION

■ To start LEAVE HOME operation

Press

(LEAVE HOME) button during stop or operation.

●

Room temperature is set at 10°C and heating operation starts.

“

”, “ ”, “ ”, “ ” is displayed on the LCD.

Press

(LEAVE HOME) button during stop or operation.

Room temperature is set at 10°C and heating operation starts.

“

”, “ ”, “ ”, “ ” is displayed on the LCD.

● Set number of operation days (1 to 99 days), if needed.

Press

(TIME) button to select number of days.

Number of days blink.

* Press “

(UP)” to set number of days from 1 day, 2 days, 3

days ..... 98 days, 99 days, 1 day and so on.

* Press “

(DOWN)” to set number of days from 99 days, 98

days, 97 days .... 3 days, 2 days, 1 day, 99 days and so on.

* Number of day is counted when clock indicates 0:00.

● Press (SEND) button to confirm number of operation

days. Display for number of operation days will stop blinking.

● Press (CANCEL) button to reset number of operation

days or to have continuous operation.

■ To cancel LEAVE HOME operation

● Press (START/STOP) button.Or

● Press (LEAVE HOME) button again.

● Change to other operation mode by pressing (MODE) button.

NOTE

● After reaching the set number of operation days for Leave Home or by pressing the (Leave Home) button again,

● During Leave Home operation, fan speed and horizontal air deflector position cannot be changed.

● By pressing (Leave Home) button, implementation of Weekly Timer or One Timer only Timer is cancelled.

● In case of power supply shut down, after autorestart, all setting for number of days operation will be reset and unit

shall be in continuous operation.

●

For multi connections, when each room is running in different operation mode such as FAN only, COOLING, DEHUMIDIFYING

or AUTO mode, Leave Home operation cannot operate even though it is possible to set Leave Home operation.

In order to start Leave Home operation, all rooms must stop its operation. Then, press (LEAVE HOME) button to

operate Leave Home operation.

● For multi connections, when all rooms are running HEATING operation, it is possible to operate Leave Home operation

by pressing the (LEAVE HOME) button.

● For multi connections, if two or more rooms are set to operate Leave Home operation, the capability to reach the

set temperature at 10°C may not possible. In addition, this also depends on outdoor temperature.

Continuous operation

Day timer operation

Prevent the room temperature from falling too much by setting temperature automatically when no one is at home.

This operation is able to operate by" Continuous operation" or " Day timer operation" . Please use " Day timer operation"

to set the number of days up to 99 days.

10°C

°

●

Option 1. Continuous operation.

Option 2. Day timer operation.

Return to previous operation mode.Or

othe unit will operate in previous mode.

POWERFUL,SILENT and ECO operations are not applicable during Leave Home.

●

1

– 19 –

ENGLISH

– 19 –

HSILGNE

LEAVE HOME(LH) OPERATION

■ To start LEAVE HOME operation

Press

(LEAVE HOME) button during stop or operation.

●

Room temperature is set at 10°C and heating operation starts.

“

”, “ ”, “ ”, “ ” is displayed on the LCD.

Press

(LEAVE HOME) button during stop or operation.

Room temperature is set at 10°C and heating operation starts.

“

”, “ ”, “ ”, “ ” is displayed on the LCD.

● Set number of operation days (1 to 99 days), if needed.

Press

(TIME) button to select number of days.

Number of days blink.

* Press “

(UP)” to set number of days from 1 day, 2 days, 3

days ..... 98 days, 99 days, 1 day and so on.

* Press “

(DOWN)” to set number of days from 99 days, 98

days, 97 days .... 3 days, 2 days, 1 day, 99 days and so on.

* Number of day is counted when clock indicates 0:00.

● Press (SEND) button to confirm number of operation

days. Display for number of operation days will stop blinking.

● Press (CANCEL) button to reset number of operation

days or to have continuous operation.

■ To cancel LEAVE HOME operation

● Press (START/STOP) button.Or

● Press (LEAVE HOME) button again.

● Change to other operation mode by pressing (MODE) button.

NOTE

● After reaching the set number of operation days for Leave Home or by pressing the (Leave Home) button again,

● During Leave Home operation, fan speed and horizontal air deflector position cannot be changed.

● By pressing (Leave Home) button, implementation of Weekly Timer or One Timer only Timer is cancelled.

● In case of power supply shut down, after autorestart, all setting for number of days operation will be reset and unit

shall be in continuous operation.

●

For multi connections, when each room is running in different operation mode such as FAN only, COOLING, DEHUMIDIFYING

or AUTO mode, Leave Home operation cannot operate even though it is possible to set Leave Home operation.

In order to start Leave Home operation, all rooms must stop its operation. Then, press (LEAVE HOME) button to

operate Leave Home operation.

● For multi connections, when all rooms are running HEATING operation, it is possible to operate Leave Home operation

by pressing the (LEAVE HOME) button.

● For multi connections, if two or more rooms are set to operate Leave Home operation, the capability to reach the

set temperature at 10°C may not possible. In addition, this also depends on outdoor temperature.

Continuous operation

Day timer operation

Prevent the room temperature from falling too much by setting temperature automatically when no one is at home.

This operation is able to operate by" Continuous operation" or " Day timer operation" . Please use " Day timer operation"

to set the number of days up to 99 days.

10°C

°

●

Option 1. Continuous operation.

Option 2. Day timer operation.

Return to previous operation mode.Or

othe unit will operate in previous mode.

POWERFUL,SILENT and ECO operations are not applicable during Leave Home.

●

1

– 20 –

– 2 0 –

HSILGNE

CLEAN (ONE TOUCH CLEAN) OPERATION

Drying indoor heat exchanger after cooling operation to prevent mildew.

■ To start CLEAN operation

■ To cancel CLEAN operation

● Press (CLEAN) button when unit is OFF.

Total time taken for One Touch Clean operation is 60 minutes.

During this operation, HEATING or FAN operation shall

operate.

During one touch clean, operation lamp is blinking.

“

”, “ ” is displayed on the LCD.

● Press (START/STOP) button.Or

● Press (CLEAN) button again.

1

NOTE

● When CLEAN operation finish, unit will switch OFF automatically.

●

● For multi connections, when pressing (CLEAN) button, operation is limited to FAN operation.

● For multi connections, when one room operates CLEAN operation first, other rooms can operate

COOLING, DEHUMIDIFYING or FAN operation. However, when other rooms need to operate HEATING

operation, air conditioner will be in STANDBY mode. After CLEAN operation finish, HEATING operation

will start.

If Weekly Timer or Once Timer is set, there is a need to cancel those timer before operating CLEAN function.

– 21 –

HSILGNE

ONCE TIMER (ON/OFF TIMER) OPERATION

The device can be set to turn off at a preset time.

1. Press

(OFF-TIMER) button. and blink on the display.

2. Set the "turn-off time" with

(TIME) button.

3. After setting, direct the remote controller towards the indoor and press

(SEND) button.

and "set time" lights up instead of blinking.

A beep sound emitted from indoor unit and the (TIMER) lamp on the

indoor unit lights up.

ON TIMER

The device will turn on at a designated time.

1. Press

(ON-TIMER) button. and blink on the display.

2. Set the "turn-on time" with

(TIME) button.

3. After setting, direct the remote controller towards the indoor and press

(SEND) button.

and "set time" light up instead of blinking.

A beep sound emitted from indoor unit and the (TIMER) lamp on the indoor

unit lights up.

ON/OFF TIMER

● The device will turn on (off) and off (on) at the designated time.

● The switching occurs first at the preset time that comes earlier.

● The arrow mark appears on the display to indicate the sequence of switching

operations.

1. Press

(OFF-TIMER) button so that and blink on the

display.

2. Set the "turn-off" time with

(TIME) button. After setting, direct the remote

controller towards the indoor and press

(SEND) button.

3. Press

(ON-TIMER) button so that and set "turn-off" time light up.

The

and blink.

4. Set the "turn-on" time with

(TIME) button.

5. After setting, direct the remote controller towards the indoor and press

(SEND) button

and set "turn-on" time light up instead of blinking.

A beep sound emitted from indoor unit and the (TIMER) lamp on the indoor

unit lights up.

■

The timer may be used in three ways: OFF-timer, ON-timer and ON/OFF (OFF/ON)-

timer. Set the current time first because it serves as a reference.

■ To cancel Reservation

●

Point the signal window of the remote controller towards the indoor unit and press (CANCEL) button.

and "ON or OFF set time" goes out with a beep and the (TIMER) lamp on the indoor unit turns off.

NOTE

●

User can set only one of the OFF-timer, ON-timer or ON/OFF-timer.

●

If WEEKLY TIMER already set, by setting the ONCE TIMER, ONCE TIMER operation is prioriti zed. When

ONCE TIMER operation is complete, WEEKLY TIMER operation will be activated.

OFF TIMER

1

La pagina sta caricando ...

Hitachi RAK-25PPA Manuale utente

Questo manuale è adatto anche per

Hitachi RAK-25PPA Manuale utente

in altre lingue

Documenti correlati

Altri documenti