Tripp Lite SmartOnline SU6000RT3U Manuale del proprietario

Owner’s Manual

1111 W. 35th Street • Chicago, IL 60609 USA

Customer Support: (773) 869-1234 • Application Services: (773) 869-1236 • www.tripplite.com

SmartOnline

™

Single-Phase 6kVA & 10kVA

Intelligent True On-Line UPS Systems

(Rackmount/Tower)

For all UPS system modules (power module, isolation transformer module and battery module)

sold either separately or combined. Select UPS system modules may include separate instruction

or warning sheets which should be used in conjunction with this manual.

Important Safety Warnings

Mounting

Connection

Features

Operation

Service/Warranty and Insurance

Specifications

Español/Français/Ðóññêèé

2

3

5

9

16

19

20

23/45/67

Optional Connection

13

Power ON/OFF

14

Manual Bypass Operation

15

2

Important Safety Warnings

SAVE THESE INSTRUCTIONS. This manual contains important instructions and warnings that should be followed during the installation and

maintenance of all Tripp Lite SmartOnline Rackmount/Tower UPS Systems and their batteries.

UPS Location Warnings

• Install your UPS indoors, away from excess moisture or heat, direct sunlight, dust and conductive contaminants.

• Install your UPS in a structurally sound area. Your UPS is extremely heavy; take care when moving and lifting the unit.

• Only operate your UPS at indoor temperatures between 32° F and 104° F (between 0° C and 40° C). For best results, keep indoor

temperatures between 62° F and 84° F (between 17° C and 29° C).

• Leave adequate space around all sides of the UPS for proper ventilation.

• Do not install the UPS near magnetic storage media, as this may result in data corruption.

UPS Connection Warnings

• The power supply for this unit must be single-phase rated in accordance with the equipment nameplate. It also must be suitably grounded.

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems in life support applications in which a malfunction or failure of a Tripp Lite UPS System could

cause failure or significantly alter the performance of a life support device.

• Connect your UPS power module’s and/or isolation transformer module’s grounding terminal to a grounding electrode conductor.

• The UPS is connected to a DC energy source (battery). The output terminals may be live when the UPS is not connected to an AC supply.

Maintenance Warnings

• Your UPS power module, isolation transformer module and battery module(s) do not require routine maintenance. Do not open them

for any reason. There are no user-serviceable parts inside.

Battery Warnings

• Do not operate your UPS without connecting it to an external battery module.

• Connect only Tripp Lite battery modules to your UPS power module’s external battery connector.

• The batteries in your battery module are recyclable. Refer to local codes for disposal requirements, or if in the USA call

1-800-SAV-LEAD (1-800-728-5323) for complete recycling information. CAUTION: Do not dispose of the batteries in a fire, as this

could cause the battery to explode.

• Because the batteries present a risk of electrical shock and burn from high short-circuit current, batteries should be changed only by

trained service personnel observing proper precautions. Consult your battery module manual before proceeding. Remove watches,

rings, and other metal objects. Use tools with insulated handles. Wear rubber gloves and boots. Do not lay tools or metal parts on top

of the batteries. Do not short or bridge the battery terminals with any object. Disconnect the charging source prior to connecting or

disconnecting battery terminals. Determine if the batteries are inadvertently grounded. If inadvertently grounded, remove the source

of the ground. Contact with any part of a grounded battery can result in electrical shock. The likelihood of such shock will be reduced

if such grounds are removed during installation and maintenance.

• Do not open or mutilate the batteries. Released electrolyte is harmful to the skin and eyes, and may be toxic.

• Fuses should be replaced only by factory authorized personnel. Blown fuses should be replaced only with fuses of the same number

and type.

• Service and repair should be done only by trained personnel. During any service work to the UPS, it should be turned off or manually

bypassed via the transformer. Note that potentially lethal voltages exist within this unit as long as the battery supply

is connected.

• Do not connect or disconnect battery module(s) while the UPS is operating from the battery supply or when the transformer module

is not in bypass mode (if your UPS system includes a transformer module).

• During “hot-swap” battery module replacement your UPS will be unable to provide battery backup in the event of a blackout.

3

Mounting (Rack)

1

4-Post Mounting

1

2

3

A

B

C

F

E

G

4

H

Connect the two segments of each shelf using the included attached screws and

wing nuts . Leave the screws slightly loose so that the shelves can be adjusted in

the next step.

Adjust each shelf to fit your rack, then mount them in the lowest available space

of your rack with the screws, nuts and washers provided . Note that the support

ledges should face inward. Tighten the wingnuts that connect the shelf segments .

Attach mounting ears to the front mounting holes of your equipment using

the screws provided . The ears should face forward.

Using an assistant, lift your equipment and slide it onto the mounting shelves.

Attach your equipment to the rack by passing the screws, nuts and washers

(user-provided) through its mounting ears and into the rack rails.

To mount your equipment in a 2-post rack, you must purchase a Tripp Lite 2-Post

Rackmount Installation Kit (model: 2POSTRMKIT, sold separately) for each module

installed. See the Installation Kit's owner's manual for complete mounting instructions.

H

G

FE

D

C

B

A

4

Mount your equipment in either a 4-post or 2-post rack or rack enclosure.The user must determine the fitness of hardware and procedures

before mounting. If hardware and procedures are not suitable for your application, contact the manufacturer of your rack or rack enclosure.

The procedures described in this manual are for common rack and rack enclosure types and may not be appropriate for all applications.

2

3

2-Post (Telecom) Mounting

B

D

4

Mounting (Tower)

The UPS system is shipped with two sets of plastic feet and extensions that

can be used to tower mount the UPS’s power module, a battery module and either an

isolation transformer module or a second battery module.

Adjust the feet to a width of 10.25 inches (26 cm) for a UPS power module and

battery module, or to a width of 15.375 inches (39 cm) for three units. Align the feet

in your installation area, approximately 10 inches (26 cm) apart. Have one or more

assistants help you place the units on their sides in the feet. The control panel of

the UPS should be the UPS’s upper corner and face outward. If you are installing

a transformer module, place it between the UPS power module and its battery module.

Rotate the power module’s Control Panel to view it easier while the UPS is tower

mounted. Insert a small screwdriver, or other tool, in the slots on either side of the

Control Panel. Pop the panel out; rotate it; and pop the panel back into place.

BA

1

A

B

Mount all modules in an upright, tower position using included base stands. The user must determine the fitness of hardware and procedures

before mounting.

2

5

Features

There are three separate UPS system modules available from Tripp Lite (a power module, an isolation transformer module and a battery

module) used in a variety of combinations. Familiarize yourself with the location and function of the features on each module before

installing and operating your UPS system. The power module is the only module which includes front panel features.

Power Module Front Panel Controls

1. LCD DISPLAY: This backlit (16 × 2 character) dot matrix display indicates a wide range of UPS operating conditions and diagnostic

data. It also displays UPS settings and options when the UPS is in setup mode.

2. ON/MUTE BUTTON: Press this button and hold it until you hear a beep to turn the UPS system’s inverter ON. If the UPS’s battery

alarm is sounding, press this button to silence it.

3. SCROLL DOWN/EXIT SETUP BUTTON: This button allows you to browse through different options and power readings on the

LCD display. Momentarily pressing it causes the LCD screen to display a different power reading (see “Operation”, pg. 18). Pressing it

and the SCROLL UP Button together puts the UPS in setup mode, where this button is used to scroll through setup options and to exit

setup mode.

4. SCROLL UP/SELECT BUTTON: This button allows you to browse through different options and power readings on the LCD dis-

play. Momentarily pressing it causes the LCD screen to display a different power reading (see “Operation”, pg. 18). Pressing it and the

SCROLL DOWN Button together puts the UPS in setup mode, where this button is used to select setup options.

5. OFF BUTTON: Press this button until you hear a beep to turn the UPS system’s inverter OFF.

6. O/P (OUTPUT) LED: This green light will illuminate to indicate your UPS is supplying AC power to connected equipment.

7. DC/AC (INVERTER) LED: This green light will illuminate to indicate the UPS’s DC/AC inverter is activated.

8. BYPASS LED: This green light will illuminate when the UPS is providing filtered mains power without engaging its converter or

inverter. If this LED is lit, connected equipment will not receive battery power in the event of a blackout.

9. AC/DC (Converter) LED: This green light will illuminate to indicate the UPS’s AC/DC converter is charging the connected battery pack(s).

10. BATTERY LED: This red light will illuminate when the UPS is discharging the battery to provide connected equipment with AC

power. An alarm will sound which can be silenced by pressing the ON/MUTE Button. This LED will remain lit after the alarm is

silenced.

11. I/P (INPUT) LED: This green light will illuminate to indicate an AC input supply is present.

12. ACCESS SLOTS: To rotate the controls, insert a flathead screwdriver into these slots and gently lever the panel out. Taking care not

to excessively twist or yank the cables connecting the controls to the rest of the UPS, turn the controls to the desired orientation and

reinsert them.

1

2 345

6879

10

11

12

Features (Rear Panel)

see page 8 for feature descriptions

6kVA Power Module

6kVA Isolation Transformer Module

Battery Module for 6kVA and 10kVA Models

54

6

7

89

10

16

17

15

12

20

21

3

6

1 2

11

13

18

19

7

Features (Rear Panel)

see page 8 for feature descriptions

10kVA Power Module

45

6

7

8

9

10

3

Battery Module for 6kVA and 10kVA Models

20

21

10kVA Isolation Transformer Module

16

14

11

12

17

12

15

18 19

8

Features (Rear Panel)

continued

Power Module Feature Description

(6kVA and 10kVA models)

1. Output Terminal Block: Use these terminals to connect your power module to your equipment or to the transformer module. Unscrew

and remove the cover over the block for access.

2. Input Terminal Block: Use these terminals to connect your power module to utility power or to the transformer module. Unscrew and

remove the cover over the block for access.

3. External Battery Connector: Use this to connect one or more Tripp Lite battery modules to the power module. Remove the cover for

access. The power module will not start without a connection to a charged battery module. Refer to the battery module owner’s manual

for connection instructions and safety warnings.

4. AC Input Breaker: One double-pole circuit breaker controls input power to the power module.

5. AC Output Breaker: One double-pole circuit breaker controls output power from the power module.

6. Exhaust Fan: This cools and ventilates the inside of the power module.

7. Accessory Slot: Remove the small cover panel to install optional accessories to remotely control and monitor your UPS system. Visit

Tripp Lite on the Web (www.tripplite.com) to learn about available SNMP, network management and connectivity products that may be

installed in this slot.

8. EPO (Emergency Power Off) Port: The power module features an EPO port that may be used to connect the power module to a contact

closure switch to enable emergency power off. See “Optional Connection” section for details.

9. RS-232 Communication Port: This female DB9 serial port may be used to connect your UPS to a workstation or server. It uses RS-232

protocol to communicate with a connected computer. It is used with Tripp Lite software and the included serial cable to monitor and

manage the UPS remotely over a network and to automatically save open files and shut down equipment during a blackout. See

“Optional Connection” for details.

10. Dry Contact Interface Port: This female DB9 port sends contact-closure signals to indicate line-fail and low-battery status. See

“Optional Connection” for details.

Isolation Transformer Module Feature Description

(6kVA and 10kVA models)

11. Utility Input Terminal Block: Use these terminals to connect your transformer module to utility power. Unscrew and remove the cover

over the block for access.

12. Equipment Output Terminal Block: Use these terminals to connect your equipment to the transformer module. Unscrew and remove

the cover over the block for access.

13. Cable for Power Module Connection (6kVA models only): Connects the transformer module to the power module’s input/output after

the power module’s terminal blocks have been removed. See “Connection” section for details.

14 Hardwire Terminal Block for Power Module Connection (10kVA models only): Use these terminals to connect the transformer mod-

ule to the power module’s input and output terminal blocks. See “Connection” section for details.

15. Overtemperature Reset Breaker: This circuit breaker trips if the unit’s temperature climbs too high.

16. AC to UPS Breaker: One double-pole circuit breaker controls the transformer module’s power output to the UPS.

17. Output Breaker: One triple-pole circuit breaker controls the transformer module’s power output to connected equipment.

18. Manual Bypass Switch: This red and yellow dial is used to circumvent the power module while still supporting connected equipment

when performing power module maintenance. While this switch is on BYPASS, connected equipment will receive filtered AC mains

power from the transformer module, but the equipment will not receive battery power in the event of a blackout. See “Manual Bypass

Operation” section for complete bypass procedure.

WARNING! For qualified service personnel only. Failure to follow the bypass procedure completely will not adequately power

down the UPS power module, resulting in the continued risk of death or injury from potential contact with high voltage.

19. Input Voltage Select Switch: Use this switch to set the transformer module's input voltage (either 200V AC, 208V AC or 240V AC).

See “Connection” section for details.

Battery Module Feature Description

(6kVA and 10kVA models)

20. Input Connector: Use this connector to daisy chain additional battery modules onto the first. Remove the cover panel for access. Refer

to the battery module owner’s manual for connection instructions and safety warnings.

21. Output Cable: Use this cable to connect the battery module to the power module or to another battery module. The power module will not start

without a connection to a charged battery module. Refer to the battery module owner’s manual for connection instructions and safety

warnings.

9

There are three separate UPS system modules available from Tripp Lite (a power module and a battery module, which are required in all

applications, and an isolation transformer module) used in a variety of combinations. Follow the connection procedure below which matches

the combination of modules which you plan on installing.

Connection Combination #1:

Power Module (either 6kVA or 10kVA) + Battery Module(s)

Hardwire the power module to your equipment.

Using a screwdriver, remove the top of the box covering the power module’s

input and output terminals. Pass a user-supplied cable through the terminal

box’s left knockout and connect it to the power module’s output terminals.

Connect the other end of the cable to your equipment.

Hardwire the power module to a utility power source.

Pass a user-supplied cable through the box’s right knockout and connect it

to the power module’s input terminals. Replace the top of the terminal box.

Connect the other end of the cable to a utility power source.

Connect the battery module to the power module.

Consult the owner’s manual that came with your battery module. Fully insert

the connector on the end of the battery module’s cable into the connector

on the rear panel of the power module . Small sparks may occur; this is

normal. NOTE: the power module does not contain internal batteries and will not

start until a battery module is connected. The battery modules are fully charged

prior to shipping. However, before expecting full backup capability (particularly

if the battery module has been stored for an extended period) after the UPS system

is connected to a utility power source, allow the battery module to recharge for

12 hours. Once the UPS system is in use, it will charge the batteries and maintain

the charge level automatically. If needed, connect additional battery modules

in a daisy-chain with each module’s cable inserted into the previous module’s

connector .

F

E

D

C

B

A

1

2

Connection

• Wiring must be done by a qualified electrician.

• The UPS power module may be installed on its own or connected to an isolation transformer module. Both applications require the power module

to be connected to a battery module.

• When making wiring connections, observe the cable connection regulations appropriate to your area [e.g. National Electrical Code (NEC)

in the U.S.] at all times. Be sure to install an easily accessible disconnect switch in your installation wiring so you may cut off the UPS’s

AC input during fires and other emergencies. Ensure that cables are fitted with cable sleeves and are secured by connector clamps. Tighten

connections with a torque of not less than 24-28 inch-pounds (2.7-3.2 NM).

• Make sure that your equipment is properly grounded.

• Using cables of improper size may damage your equipment and cause fire hazards. Choose appropriate cabling and protection circuits to

make wiring connections (Ground conductors must be the same size and type as the power conductors used):

RATED INPUT CURRENT RATED OUTPUT CURRENT RATED OUTPUT CURRENT OUTPUT PROTECTION

200 - 240 (1Ø, 2-Wire + PE) 200 - 240V (1Ø, 2-Wire + PE) 120V (1Ø, 2-Wire + PE) CIRCUIT

6kVA Models 30A 8 AWG (10mm

2

) 30A 8 AWG (10mm

2

) 2 × 30A 8 AWG (10mm

2

) 30A

10kVA Models 50A 6 AWG (16mm

2

) 50A 6 AWG (16mm

2

) 2 × 50A 6 AWG (16mm

2

) 63A

Connecting Modules to Each Other and to Utility Power and Equipment

Hardwiring Cautions

3

A

B

C

D

E

F

1

6kVA Power Module Shown

10

Connection Combination #2:

Power Module (6kVA) + Transformer Module (6kVA) + Battery Module(s)

Connect the power module to the transformer module.

Using a screwdriver, remove the entire box covering the power module’s

input and output terminals. Remove the screws on either side of the terminals.

Grip the terminals and slide them out until you can view the cable connector

release tab . Press the tab down and pull on the cables to release them from

the internal connector . Remove the terminals. Insert the connector cable

from the transformer module into the internal connectors in the power module’s

terminal box until the release tab clicks in place. Replace the screws around

the plate. Although they are not needed, retain the power module’s terminals

and terminal box cover in case you plan to operate the power module without

the transformer module at a future date.

Hardwire the transformer module to your equipment.

Using a screwdriver, remove the top of the box covering the transformer

module’s input and output terminals. Pass a user-supplied cable through the

box’s left knockout and connect it to the transformer module’s output ter-

minals. See the AC Output Voltage Diagram to determine which terminal

connections will provide voltage appropriate to your application. Connect the

other end of the cable to your equipment.

Hardwire the transformer module to a utility

power source.

Pass a user-supplied cable through the box’s right knockout and connect it to

the transformer module’s input terminals. Replace the top of the box covering

the transformer module’s terminals. Connect the other end of the cable to a utility

power source.

I

H

G

F

E

D

C

B

A

1

3

Connection

continued

N

O

R

M

A

L

BY

PAS

S

2

120V

240V

120V

208V

AC OUTPUT VOLTAGE DIAGRAM

G

N

O

R

M

A

L

BY

PAS

S

3

N

O

R

M

A

L

BY

PAS

S

1

A

B

C

D

E

G

I

F

Connection Combination #2 continued on next page

H

Select the transformer module’s input voltage.

Using a screwdriver, remove the panel covering the transformer module’s

Input Voltage Select Switch . Set the switch to match your facility’s input

voltage. Then, use the power module’s front panel switches to configure input

voltage on the LCD Display (see “Configure your UPS’s input and output” in

the “Power ON/OFF” section on page 14).

IMPORTANT NOTE: if your facility’s input voltage is 200V AC, set the trans-

former module’s switch to 240V AC, but configure the power module to 200V

AC. If your facility’s input voltage is either 208V AC or 240V AC, the trans-

former module and power module settings must match. The factory default

settings for both modules is 208V. See chart below.

Transformer Module Power Module

Your Facility's Input Voltage Setting Input Voltage Setting

Input Voltage (Rear Panel Switch) (Front Panel Switches/LCD Display)

240V AC 240V AC 240V AC

208V AC 208V AC 208V AC

200V AC 240V AC 200V AC

Connect the battery module to the power module.

Consult the owner’s manual that came with your battery module. Fully insert

the connector on the end of the battery module’s cable into the connector on

the rear panel of the power module . Small sparks may occur; this is normal.

NOTE: the power module does not contain internal batteries and will not start

until a battery module is connected. The battery modules are fully charged prior

to shipping. However, before expecting full backup capability (particularly if

the battery module has been stored for an extended period) after the UPS system

is connected to a utility power source, allow the battery module to recharge for

12 hours. Once the UPS system is in use, it will charge the batteries and maintain

the charge level automatically. If needed, connect additional battery modules in

a daisy-chain with each module’s cable inserted into the previous module’s

connector .

Connection Combination #3: Power Module (10kVA)

+ Transformer Module (10kVA) + Battery Module(s)

Hardwire the power module to the transformer module.

Using a screwdriver, remove the top of the box covering the power module’s input

and output terminals. Remove the top of the box covering the transformer

module’s terminals. With supplied cable, connect the power module’s input and

output terminals to the corresponding terminals on the transformer module’s

“Hardwire Terminal Block for Power Module Connection” in the box’s right

knockout .

Hardwire the transformer module to your equipment.

Pass a user-supplied cable through the box’s left knockout and connect it to

the transformer module’s output terminals. See the AC Output Voltage Diagram

to determine which terminal connections will provide voltage appropriate to

your application. Connect the other end of the cable to your equipment.

E

D

C

B

A

M

L

K

J

11

Connection

continued

NORMAL

BY

PAS S

240V AC

208V AC

4

5

N

O

R

M

A

L

BY

PAS

S

5

NORMAL

BY

PAS

S

1

N

O

R

M

A

L

BY

PASS

2

4

J

M

L

A

B

C

D

K

Connection Combination #3 continued on next page

120V

240V

120V

208V

AC OUTPUT VOLTAGE DIAGRAM

G

E

12

Connection

continued

Hardwire the transformer module to a utility

power source.

Pass a user-supplied cable through the box’s middle knockout and connect

it to the transformer module’s input terminals. Connect the other end of the

cable to a utility power source. Replace the top of the boxes covering the power

module’s and transformer module’s terminals.

Select the transformer module’s input voltage.

Using a screwdriver, remove the panel covering the transformer module’s

Input Voltage Select Switch . Set the switch to match your facility’s input

voltage. Then, use the power module’s front panel switches to configure input

voltage on the LCD Display (see “Configure your UPS's input and output” in

the “Power ON/OFF” section on page 14).

IMPORTANT NOTE: if your facility's input voltage is 200VAC, set the trans-

former module’s switch to 240V AC, but configure the power module to 200V

AC. If your facility’s input voltage is either 208V AC or 240V AC, the trans-

former module and power module settings must match. The factory default

settings for both modules is 208V. See chart below.

Transformer Module Power Module

Your Facility’s Input Voltage Setting Input Voltage Setting

Input Voltage (Rear Panel Switch) (Front Panel Switches/LCD Display)

240V AC 240V AC 240V AC

208V AC 208V AC 208V AC

200V AC 240V AC 200V AC

Connect the battery module to the power module.

Consult the owner’s manual that came with your battery module. Fully insert

the connector on the end of the battery module’s cable into the connector

on the rear panel of the power module . Small sparks may occur; this is normal.

NOTE: the power module does not contain internal batteries and will not supply

power to connected equipment until a battery module is connected. The battery

modules are fully charged prior to shipping. However, if the battery module

has been stored for an extended period, after the UPS system is connected to a

utility power source, allow the battery module to recharge for 12 hours. If

needed, connect additional battery modules in a daisy-chain with each module’s

cable inserted into the previous module’s connector .

J

I

H

G

F

3

N

O

R

M

A

L

BY

PAS

S

3

4

N

O

R

M

A

L

BY

PAS

S

5

F

NORMAL

BY

PAS S

240V AC

208V AC

4

G

H

I

J

The following connections are optional. Your UPS system will function properly without

these connections.

RS-232 Serial Communication Connection

Use the included cable to connect the power module’s “RS-232” port to the communication

port on your computer. This will allow full network monitoring and control of your

UPS system. Install on your computer the Tripp Lite PowerAlert Software appropriate

to your computer’s operating system.

Contact-Closure Communication Connection

Use a user-supplied contact-closure DB9 cable to connect the power module’s “Dry-

Contact” port to the communication port on your computer or other equipment. This

will allow basic contact-closure signals to be sent to and from the UPS. Refer to the

following diagram and table to determine the signals carried by this port. Install on your

computer the Tripp Lite PowerAlert Software appropriate to your computer’s operating system.

EPO Port Connection

This optional feature is only for those applications which require connection to a facility’s

Emergency Power Off (EPO) circuit. When the power module is connected to this circuit,

it enables emergency shutdown of the output. Using the included cable, connect the

power module’s EPO port to a user-supplied remote switch. The pin assignments for the

EPO port are shown in the following diagram. Note: if there is a short between pins 2

and 3, 2 and 5, 4 and 5, or 3 and 4, the UPS system will power off.

13

Optional Connection

0

12 V

>2 sec



54321

9

8

7

6



NO

COM NC

lm in. > 3.3 mA

BACK-UP

REMOTE SHUTDOWN SIGNAL

FROM EXTERNAL

SIGNAL FROM COMPUTER

COM NC

LOW BATTERY

NO

MAXIMUM CAPACITY OF DRY CONTACT: AC250V/3A • DC30V/3A

DRY CONTACT INTERFACE DIAGRAM

UPS Operating Pin 8,3 Pin 1,3 Pin 6,3

Mode

Normal OPEN OPEN *

Back Up CLOSE * *

Low Battery CLOSE CLOSE *

Fault * * CLOSE

* Inactive: may be in either state

DRY CONTACT INTERFACE TABLE

1

2

3

4

5

6

X

12V

X

1K



EPO PIN ASSIGNMENT

14

1. Configure your UPS’s input and output: Put your UPS power module into setup mode by holding down both of its scroll buttons (

and ) at once. Scroll through the setup options (using or ) and select the appropriate setting for each of the following options using

the “SELECT” button .

• Input & Output Voltage: Select 200, 208 or 240 VAC.

• Output Frequency: Your UPS will autoselect 50 or 60 Hz to match the input.

• Economy Mode: Your UPS can provide on-line operation with zero transfer time. It can also operate in a more energy-efficient

line-interactive mode. Select Economy On to put the UPS in line-interactive mode. Select Economy Off to put the UPS in on-line mode.

• After you have set these options, “exit” the setup mode with the scroll button , then exit bypass mode by holding the ON

button down until you hear a beep.

2. Turn input to the UPS ON: If the UPS power module is connected to a transformer module, turn the tranformer module’s AC-to-UPS

and Output Circuit Breakers on. Turn the UPS power module’s Input Circuit Breaker on. Press the UPS power module’s ON button

until you hear a beep to begin inverter operation. If your AC input is not providing power normally, you may “cold start” your UPS

from battery. (Your battery must be at least partially charged for this operation to succeed.) Press and hold the “ON” button until you

hear a beep to start your UPS in ON BATTERY mode. Note that some electronic equipment may draw more amps during startup; when

starting from battery, consider reducing the initial load on the UPS. Your UPS will perform a brief self-test and show the results on the

LCD Display . See “Startup Self-Test” in the “Operation” section for the display sequence.

3. Turn UPS output ON: Turn the UPS power module’s Output Circuit Breaker ON. If the UPS is connected to a transformer module, turn

the transformer module’s Manual Bypass Switch from BYPASS to NORMAL and its Output Circuit Breaker ON. Your UPS will now

provide power to connected equipment.

4. To turn the UPS power module and transformer module OFF: Press the UPS power module’s OFF button until you hear a beep.

Your load will still be energized. The inverter is now off, but your UPS is not fully deactivated. The LCD Display will show BYPASS

MODE. Turn the UPS power module’s Input and Output Circuit Breakers ( and ) OFF. If the UPS is connected to a transformer module,

turn the transformer module’s power AC-to-UPS and Output Circuit Breakers OFF. Your load will no longer be energized, and the

LCD Display will be dark.

F

D

HE

F

E

I

H

F

C

ED

C

A

B

BAB

A

Power ON/OFF

NORMAL

BY

PA

S

N

O

R

M

A

L

B

Y

P

A

S

6kVA Models

10kVA Models

D

E

H

I

E

H

I

6kVA & 10kVA Models

(Front Panel)

D

F

C

A

B E

15

Manual Bypass Operation

(for power module maintenance or replacement)

The following procedure only applies to UPS system configurations that include a 6kVA or 10kVA transformer module. The procedure

details how to service or replace the power module while supplying equipment connected to the transformer module with utility power.

NOTE: since the power module and battery module will be disconnected during the procedure, they will be unable to supply battery backup

support to equipment connected to the transformer module in the event of a blackout.

WARNING! For qualified service personnel only. Failure to follow this procedure completely will not adequately power down the

UPS power module, resulting in the continued risk of death or injury from potential contact with high voltage.

1. Disable PowerAlert Software and disconnect communication cable from the power module’s communication ports .

2. Turn transformer module’s Bypass Switch to “BYPASS”.

3. Press power module’s OFF Button , if power module is powered, until a beep is heard and a “BYPASS MODE” message is displayed

in the LCD panel .

4. Turn off the transformer module's double-pole AC to UPS breaker .

5. Turn off the power module’s double-pole input breaker and double-pole output breaker .

6. Disconnect battery module cable from the power module’s battery connector .

7. FOR 10kVA POWER MODULES ONLY: Use a voltage meter to check the cable connecting the power module’s terminal blocks to

the transformer module’s terminal blocks to ensure the power module is no longer powered. Once it is no longer powered, remove the

cabling.

The power module is now safely powered down and maintenance/replacement can be performed.

J

I

H

GF

E

D

C

B

A

N

O

R

M

A

L

BY

PAS

S

N

O

R

M

A

L

B

Y

P

A

S

6kVA Models (Rear Panel)

10kVA Models (Rear Panel)

A

B

F

G

A

B

F

G

I

E

D

C

6kVA & 10kVA Models

(Front Panel)

H

E

H

J

16

DIAGNOSTIC MODE

AC/DC OK

DIAGNOSTIC MODE

TESTING INVERTER

ON BATTERY MODE

LOAD = XXX% X.XXKW

Operation

When you turn the UPS ON, it will enter Diagnostic Mode and perform a brief self-test lasting about 15 seconds. The results of the self-test

are shown on the LCD screen in the sequence below.

DIAGNOSTIC MODE

FREQ OUT = XXHz

DIAGNOSTIC MODE

INPUT AC OK

DIAGNOSTIC MODE

INPUT AC OK

DIAGNOSTIC MODE

BATTERY OK

DIAGNOSTIC MODE

CHARGER OK

DIAGNOSTIC MODE

AC/DC OK

DIAGNOSTIC MODE

TESTING INVERTER

ONLINE MODE

LOAD = XXX% X.XXKW

DIAGNOSTIC MODE

FREQ OUT = XXHz

DIAGNOSTIC MODE

INPUT AC BAD

DIAGNOSTIC MODE

INPUT AC BAD

DIAGNOSTIC MODE

BATTERY OK

M

STARTED WITH

AC INPUT

COLD

START*

*Note: If the UPS is cold started, its BATTERY LED will be lit.

If a problem is detected during the self-test, the LCD will display a error message. If your UPS displays any of the following messages in

its LCD, call Tripp Lite Technical Support at (773) 869-1234 for service.

BAD BATTERY!

CALL FOR SERVICE

CHARGER FAILURE!

CALL FOR SERVICE

AC/DC FAILURE!

CALL FOR SERVICE

INVERTER FAILURE!

CALL FOR SERVICE

OUTPUT FAILURE!

CALL FOR SERVICE

FAN FAILURE!

CALL FOR SERVICE

Startup Self-Test

Failed Self-Test

17

Operation

continued

During normal operation, the first line of your LCD Display shows which operating mode your UPS is in: Online, Economy, On Battery,

or Bypass.

Online mode: The UPS provides AC power while utility power is available and switches to On Battery mode instantly (zero transfer time)

if AC power is interrupted.

Economy mode: The UPS provides AC power at high efficiency while utility power is available and switches to On Battery mode quickly

if AC power is interrupted.

On Battery mode: The UPS provides AC power from battery backup so long as battery power lasts. It switches back to Online or Economy

mode if utility power is available and shuts down if it runs out of battery power.

Bypass mode: The UPS provides AC power while utility power is available. The UPS shuts down if AC power is interrupted.

The second line of the LCD Display shows basic power conditions. Push the SCROLL buttons to browse through these basic power conditions

in the sequence shown below.

XXXX MODE

LOAD = XXX% X.XXKW

XXXX MODE

IN = XXXV XX.X Hz

XXXX MODE

OUT = XXXV XX.X Hz

XXXX MODE

BATTERY = XXXVDC

M

When in the On Battery mode, the UPS power module will beep to inform you that it is using battery power to support connected equipment.

If its connected batteries are at more than half capacity, it will beep every two seconds. If its connected batteries are below half capacity, it

will beep twice a second. If its connected batteries are nearly depleted, the UPS power module will beep continuously.

To silence the On Battery Alarm, press the “ON/MUTE” button.

When the UPS detects an output overload, its LCD will switch to the following display:

The UPS will then begin a countdown. If the UPS is still overloaded at the end of the countdown, the UPS will automatically go to Bypass

Mode to protect its inverter. The duration of the countdown varies with the severity of the overload, as follows:

OVERLOAD!

LOAD = XXX% X.XXKW

Overload Condition Countdown Duration

102% - 125% 1 minute

125% - 150% 30 seconds

>150% Immediate

M

L

Normal Operation

On Battery Alarm

Overload Messages

18

Operation

continued

While in Bypass Mode, the UPS monitors its input voltage and passes that input power along to connected equipment. The UPS will not

provide battery backup in Bypass Mode.

If the output voltage deviates from an acceptable range (between 15% higher and 20% lower than nominal), the UPS displays the condition

on its LCD and stops supplying output power to its load. If power levels return to an acceptable level, the UPS resumes supplying power

to the load, and its LCD reports that output voltage was too high or too low at one time, but has returned to nominal.

>15% Higher

Than Nominal

>20% Lower

Than Nominal

Was Too High,

Now Nominal

Was Too Low,

Now Nominal

BYPASS VOLTAGE

CONDITIONS

LCD DISPLAY

MESSAGES

Your UPS will shut down and the LCD will display a message if it detects one of the following conditions. Note: During all these conditions,

the “Input,” “Output” and “Bypass” LEDs will be illuminated.

Extended

Overload

Output Short

Circuit

Remote Shutdown

Command (Via DB9)

Remote Shutdown

Command (Via EPO)

SHUTDOWN

CONDITIONS

LCD DISPLAY

MESSAGES

Internal

Faults

NO OUTPUT

BYPASS AC TOO HI

NO OUTPUT

BYPASS AC TOO LO

BYPASS MODE

BYPASS AC WAS HI

BYPASS MODE

BYPASS AC WAS LO

SHUT DOWN

OVERLOAD XXX%

SHUT DOWN

O/P SHORT CIRCUIT

SHUT DOWN

REMOTE COMMAND

SHUT DOWN

EMERGENCY STOP!

SHUT DOWN

+ DC BUS HIGH

SHUT DOWN

+ DC BUS LOW

SHUT DOWN

- DC BUS HIGH

SHUT DOWN

- DC BUS LOW

SHUT DOWN

OVERTEMPERATURE

Bypass Messages

Shutdown Messages

19

Service/Warranty and Insurance

Your SmartOnline UPS is covered by the 2-year limited warranty period described below. A variety of service contracts are also available

from Tripp Lite, including start-up service contracts and 3- to 5-year SafeSure on-site service contracts. For more information, call

Tripp Lite Customer Service at (773) 869-1234.

TRIPP LITE warrants its products including batteries to be free from defects in materials and workmanship for a period of two years from the date of initial purchase. After 90 days

from the date of purchase, TRIPP LITE’s obligation under this warranty is limited to replacing parts on such defective products. To obtain service under this warranty, you must call

TRIPP LITE or an authorized TRIPP LITE service center. Products must be returned to TRIPP LITE or an authorized TRIPP LITE service center with transportation charges prepaid

and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does not apply to equipment which has been

damaged by accident, negligence or misapplication or has been altered or modified in any way. This warranty applies only to the original purchaser who must have properly registered the

product within 10 days of purchase.

The warranties of all TRIPP LITE surge suppressors are null and void if they have been connected to the output of any UPS system.The warranties of all TRIPP LITE UPS Systems

are null and void if a surge suppressor has been connected to its output receptacles.

EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING

OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is not liable for any costs, such as lost profits or

revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.

The policy of TRIPP LITE is one of continuous improvement. Specifications are subject to change without notice.

Tripp Lite warrants, for the lifetime of the product, (at Tripp Lite's option) to repair or replace (on a pro rata basis) directly connected equipment that is damaged due to power tran-

sients while properly connected to Tripp Lite products offering the Ultimate Lifetime Insurance Policy. Power transients include spikes and surges on the AC power, data or telephone

lines that the Tripp Lite products have been designed to protect against (as recognized by industry standards).

AC Power Line Transients: To claim damages, the Tripp Lite product must be plugged into a properly wired and grounded outlet. No extension cords or other electrical connections

may be used. The installation must comply with all applicable electrical and safety codes set forth by the National Electrical Code (NEC). Except as provided above, this warranty

does not cover any damage to properly connected electronic equipment resulting from a cause other than an "AC power transient". If user meets all of the above requirements, Tripp Lite

will repair or replace (at Tripp Lite's option) equipment up to the specified value (See Ultimate Lifetime Insurance Policy Limits). No coverage is allowed for damage entering from

telephone or data lines, unless they are separately protected, as described below.

Telephone and Data Line Transients: Tripp Lite will repair or replace directly connected equipment that is damaged by transients on telephone and/or data lines only when all such

paths are protected by a Tripp Lite protection product(s) and the AC power (utility) line is simultaneously protected by a Tripp Lite power protection device (UPS, surge suppressor or

line conditioner) with Ultimate Lifetime Insurance coverage. Additional telephone and/or data line connected devices downstream must have their own telephone and/or dataline protectors.

Reimbursement dollar limits will be equal to that of the Tripp Lite power protection protector. Coverage is excluded where a suitable environment for the protection device is not provided,

including, but not limited to, lack of a proper safety ground. Telephone service equipment must also include a properly installed and operating "primary protection" device at the telephone

service entrance (such devices are normally added during telephone line installation).

All above warranties are null and void if the Tripp Lite product has been improperly installed, tampered with or altered in any way, or if the connected equipment was not used under

normal operating conditions or in accordance with any labels or instructions. All claims under this warranty must be submitted in writing to Tripp Lite within 30 days of the occurrence

or the claim will not be considered. This warranty does not include damage resulting from accident or misuse, and applies to the domestic (USA & Canada) use of these products only.

Tripp Lite reserves the right to determine whether the damage to the connected equipment is due to malfunction of the Tripp Lite product by requesting the equipment in question

be sent to Tripp Lite for examination. This policy is above and beyond, only to the extent needed, of that provided by any coverage of connected equipment provided by other sources,

including, but not limited to, any manufacturer's warranty and/or any extended warranties.

EXCEPT AS PROVIDED ABOVE, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT

OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, Tripp Lite is not liable for any costs, such as lost profits or revenue,

loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties or otherwise. Coverage also does not apply to connected medical

and industrial equipment.

To receive service under this warranty, you must be the original purchaser/user of the product in question. You must obtain a Returned Material Authorization (RMA) number from

Tripp Lite. Products must be returned to Tripp Lite with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date

and place of purchase.

Service

2-Year Limited Warranty

Ultimate Lifetime Insurance Policy

(Valid in U.S. and Canada ONLY)

20

Specifications

SU6000RT3U and SU10KRT3U models include a Power Module, Isolation Transformer Module and one Battery Module.

SU6000RT3UXR models include a Power Module, Isolation Transformer Module and two

Battery Modules.

Model SU6000RT3U SU6000RT3UXR SU10KRT3U

Input

Input Voltage Range 156V~276V Single Phase 156V~276V Single Phase 156V~276V Single Phase

Module Input Voltage 200/208/240V 200/208/240V 200/208/240V

Input Frequency 50/60 Hz ± 3 Hz 50/60 Hz ± 3 Hz 50/60 Hz ± 3 Hz

Input Current 22.6A 22.6A 40A

Inrush Current <150A <150A <200A

Power Factor (Full Load) >0.97 >0.97 >0.97

Efficiency (Full Load/On-Line) >87% >87% >88%

Power Module Circuit Breaker 40A (2 pole) 40A (2 pole) 63A (2 pole)

Transformer Module Circuit Breaker 40A (2 pole) 40A (2 pole) 63A (2 pole)

Output

VA 6000 6000 10000

Watts (Power Factor: 0.7) 4200 4200 7000

Waveform (On-Line) Sinewave Sinewave Sinewave

Waveform (On-Battery) Sinewave Sinewave Sinewave

Output Voltage (RMS) 100/120/200/208/240V 100/120/200/208/240V 100/120/200/208/240V

Output Frequency 50/60 Hz 50/60 Hz 50/60 Hz

(± 0.2 Hz on battery) (± 0.2 Hz on battery) (± 0.2 Hz on battery)

Voltage Regulation ±3% ±3% ±3%

Max. Harmonic Distortion

(Linear Full Load) <3% <3% <3%

(Non-Linear Full Load) <6% <6% <6%

Overload Capabilities 102% (continuous) 102% (continuous) 102% (continuous)

102%~125% (1 min.) 102%~125% (1 min.) 102%~125% (1 min.)

125%~150% (30 sec.) 125%~150% (30 sec.) 125%~150% (30 sec.)

>150% (Immediate) >150% (Immediate) >150% (Immediate)

Short Circuit Capability 90A* 90A* 160A*

Power Module Circuit Breaker 40A 63A 63A

Transformer Module Circuit Breaker 30A (3 pole) 63A (3 pole) 63A (3 pole)

Crest Factor 3:1 3:1 3:1

*The short circuit capability at 1ø 2W 120V for the SU6000RT3U and SU6000RT3UXR is greater than 180A, and for the SU10KRT3U is greater than 320A.

Operation

On-Line Transfer Time

(Line to Battery, Battery to Line) 0 ms 0 ms 0 ms

Audible Noise (Full Load @ 1 m) <50 dBA <55 dBA <55 dBA

Typical Backup Time (with included Battery Module)

(Full Load) 15 min. + 37 min. + 8 min. +

(Half Load) 37 min. + 79 min. + 20 min. +

Indicators

Includes an LCD Display and LEDs (I/P (input), BATTERY, AC/DC, BYPASS DC/AC, O/P (output)).

Communications

Includes an RS-232 DB9 female connector, a dry contact DB9 female connector and an accessory slot.

Physical Specifications

Unit Dimensions (H x W x D)

Power Module 5.25 (3U) x 17.5 x 22.5 in. 5.25 (3U) x 17.5 x 22.5 in. 5.25 (3U) x 17.5 x 22.5 in.

[13.4 x 44.5 x 57.2 cm.] [13.4 x 44.5 x 57.2 cm.] [13.4 x 44.5 x 57.2 cm.]

Transformer Module 5.25 (3U) x 17.5 x 26 in. 5.25 (3U) x 17.5 x 26 in. 5.25 (3U) x 17.5 x 26 in.

[13.4 x 44.5 x 66.1 cm.] [13.4 x 44.5 x 66.1 cm.] [13.4 x 44.5 x 66.1 cm.]

Battery Module #1 5.25 (3U) x 17.5 x 22.5 in. 5.25 (3U) x 17.5 x 22.5 in. 5.25 (3U) x 17.5 x 22.5 in.

[13.4 x 44.5 x 57.2 cm.] [13.4 x 44.5 x 57.2 cm.] [13.4 x 44.5 x 57.2 cm.]

Battery Module #2 (if applicable) n/a 5.25 (3U) x 17.5 x 22.5 in. n/a

[13.4 x 44.5 x 57.2 cm.]

Shipping Weight

Power Module 58 lb. 58 lb. 68 lb.

[27 kg.] [27 kg.] [31 kg.]

Transformer Module 124 lb. 124 lb. 124 lb.

[57 kg.] [57 kg.] [57 kg.]

Battery Module #1 160 lb. 160 lb. 160 lb.

[73 kg.] [73 kg.] [73 kg.]

Battery Module #2 (if applicable) n/a 160 lb. n/a

[73 kg.]

+ Backup times are expandable with additional Battery Modules (model: BP240V10RT-3U) sold separately.

La pagina sta caricando ...

Tripp Lite SmartOnline SU6000RT3U Manuale del proprietario

Questo manuale è adatto anche per

Tripp Lite SmartOnline SU6000RT3U Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti