ADEMCO Security System VISTA-15CN Installation And Setup Manual

Marca: ADEMCO

Modello: Security System VISTA-15CN

Categoria: Sistemi di controllo accessi di sicurezza

Tipo: Installation And Setup Manual

Questo manuale è adatto anche per

Security System VISTA-15

9,67$

9,67$&1

6HF XULW\6\VWHP



,QVWDOODWLRQDQG6HWXS*XLGH

K3892V2 7/01

•

RECOMMENDATIONS FOR PROPER PROTECTION

The Following Recommendations for the location of Fire and Burglary Detection Devices Help

Provide Proper Coverage for the Protected Premises.

Recommendations for Smoke and Heat Detectors

With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in

the National Fire Protection Association's (NFPA) Standard #72 noted below.

Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of

the household as follows: For minimum protection, a smoke detector should be installed outside of each separate

sleeping area and on each additional floor of a multi-floor family living unit, including basements. The installation of

smoke detectors

in kitchens, attics (finished or unfinished), or in garages is not normally recommended.

For additional protection, the NFPA recommends that you install

heat

smoke detectors

in the living room,

dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements, and

attached garages.

In addition, we recommend the following:

• Install a smoke detector inside every bedroom where a smoker sleeps.

• Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely closed.

Smoke could be blocked by the closed door. Also, an alarm in the hallway outside may not wake up the sleeper if

the door is closed.

• Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air conditioners,

or humidifiers) are used.

• Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters) long.

• Install smoke detectors in any room where an alarm control is located, or in any room where alarm control

connections to an AC source or phone lines are made. If detectors are not so located, a fire within the room could

prevent the control from reporting a fire or an intrusion.

THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR TEMPORAL

PULSE SOUNDING OF FIRE NOTIFICATION APPLIANCES.

DINING

KITCHEN

BEDROOM

LIVING ROOM

✪

▲

BEDROOM

BDRM

DINING

LIVING ROOM

TV ROOM

KITCHEN

■

✪

✪✪

✪

▲

✪

BEDROOM

■

LVNG RM

BASEMENT

KTCHN

▲

CLOSED

DOOR

GARAGE

▲

Smoke Detectors for Minimum Protection

Smoke Detectors for Additional Protection

Heat-Activated Detectors

Recommendations for Proper Intrusion Protection

For proper intrusion coverage, sensors should be located at every possible point of entry to a home or commercial

premises. This includes skylights and upper windows in a multi-level building.

In addition, we recommend that radio backup be used in a security system so that alarm signals can still be sent to the

alarm monitoring station in the event that the telephone lines are out of order (alarm signals are normally sent over the

phone lines, if connected to an alarm monitoring station).

Table of Contents

•••••••••••••••••••••••••••••••••••••••••••••••••

Table of Contents..................................................................................................................................................................... i

List of Figures ........................................................................................................................................................................iii

Conventions Used In This Manual ....................................................................................................................................iv

SECTION 1 Introduction ...................................................................................................................................................1–1

Features.............................................................................................................................................................................1–1

SECTION 2 Mounting and Wiring the Control............................................................................................................2–1

Cabinet and Lock ..............................................................................................................................................................2–1

Mounting the PC Board with RF Receiver.......................................................................................................................2–2

Wiring to Keypads.............................................................................................................................................................2–3

Sounder (Bell) Connections .............................................................................................................................................2–4

Wiring the AC Transformer..............................................................................................................................................2–5

Backup Battery .................................................................................................................................................................2–5

Earth Ground ....................................................................................................................................................................2–6

Hardwire Zones.................................................................................................................................................................2–7

4219/4229 Expansion Zones..............................................................................................................................................2–8

Installing the RF Receiver................................................................................................................................................2–9

Installing a 5800TM Module ............................................................................................................................................2–9

Installing the Transmitters............................................................................................................................................2–10

Jam Detection and Reporting.........................................................................................................................................2–10

About 5800 Series Transmitters.....................................................................................................................................2–10

Connecting Relay Modules .............................................................................................................................................2–12

Power Line Carriers........................................................................................................................................................2–13

Phone Line/Phone Module Connections.........................................................................................................................2–14

Long Range Radio Connections ......................................................................................................................................2–15

AAV Connections.............................................................................................................................................................2–15

SECTION 3 Programming Overview..............................................................................................................................3–1

About Programming..........................................................................................................................................................3–1

Entering Program Mode ...................................................................................................................................................3–1

Programming a Data Field...............................................................................................................................................3–1

Reviewing a Data Field/Erasing an Entry.......................................................................................................................3–2

Interactive Mode Programming (

✱

56,

✱

58,

✱

80,

✱

81, and

✱

82) .....................................................................................3–2

Loading Factory Defaults .................................................................................................................................................3–2

Programming System Setup Fields..................................................................................................................................3–2

Exiting the Programming Mode.......................................................................................................................................3–2

SECTION 4 Zone Response Type Definitions ..............................................................................................................4–1

Zone Type Definitions .......................................................................................................................................................4–1

SECTION 5 Data Field Programming............................................................................................................................5–1

About Data Field Programming .......................................................................................................................................5–1

Programming Data Fields ................................................................................................................................................5–1

System Setup Fields (*20 - *30)........................................................................................................................................5–1

Zone Sounds and Timing (*31 - *39) ................................................................................................................................5–2

Dialer Programming (*40 - *52) .......................................................................................................................................5–3

Zone Assignment Alarm Report Codes

(

✱

56 &

✱

58).......................................................................................................5–5

To Program System Status and Restore Report Codes

(

✱

59 –

✱

76, &

✱

89)...................................................................5–5

System Status Report Codes

(

✱

59–

✱

68) ..........................................................................................................................5–6

Restore Report Codes (

✱

70–

✱

76)......................................................................................................................................5–7

Daylight Saving Time (*77 & *78) ...................................................................................................................................5–7

Dynamic Signaling (*79)...................................................................................................................................................5–8

Output And System Setup (*80 - *82; *84, *85; *87 - *93)..............................................................................................5–8

Download Information (*94, *95) ...................................................................................................................................5–11

SECTION 6 Zone Programming ......................................................................................................................................6–1

About Zone Programming.................................................................................................................................................6–1

✱

56 Zone Programming Procedures.................................................................................................................................6–1

✱

58 Expert Programming Mode Procedures....................................................................................................................6–4

To Remove a Zone .............................................................................................................................................................6–5

To Delete a Transmitter Serial Number..........................................................................................................................6–6

To Enter and Duplicate Wireless Keys ............................................................................................................................6–6

SECTION 7 Output Device Programming ....................................................................................................................7–1

Programming Options Defined.........................................................................................................................................7–1

Programming Output Relays and Powerline Carrier Devices........................................................................................7–2

SECTION 8 Zone Lists.......................................................................................................................................................8–1

About Zone List Menu Mode.............................................................................................................................................8–1

Zone List Displays.............................................................................................................................................................8–1

Cross Zoning - Zone List 04 ..............................................................................................................................................8–1

NIGHT-STAY - Zone List 05 ............................................................................................................................................8–2

SECTION 9 Alpha Descriptor Programming ...............................................................................................................9–1

About Alpha Descriptor Programming.............................................................................................................................9–1

Zone Descriptors................................................................................................................................................................9–1

Programming Zone Descriptors (Program Menu Mode

✴

82) .........................................................................................9–1

Adding Custom Words/Numbers (not annunciated by the 4285/4286 VIP Module)......................................................9–3

SECTION 10 Remote Programming and Control (Downloading) .........................................................................10–1

About Remote Programming ..........................................................................................................................................10–1

Equipment Required.......................................................................................................................................................10–1

Initial Download..............................................................................................................................................................10–2

Remote Programming Commands..................................................................................................................................10–2

Remote Programming Advisory Notes ...........................................................................................................................10–2

SECTION 11 System Communication..........................................................................................................................11–1

Panel Communication with Central Station..................................................................................................................11–1

Report Code Formats ......................................................................................................................................................11–1

SECTION 12 System Operation.....................................................................................................................................12–1

Security Codes.................................................................................................................................................................12–1

Keypad Functions ...........................................................................................................................................................12–1

Setting the Real-Time Clock...........................................................................................................................................12–4

SECTION 13 Testing the System...................................................................................................................................13–1

Test Procedure.................................................................................................................................................................13–1

SECTION 14 Troubleshooting Guide ...........................................................................................................................14–1

SECTION 15 Specifications & Accessories .................................................................................................................15–1

Specifications...................................................................................................................................................................15–1

Accessories (Compatible Devices)...................................................................................................................................15–3

5800 RF System Wireless Transmitters .........................................................................................................................A–1

Transmitter Input Loop Identification............................................................................................................................A–1

Regulatory Agency Statements.......................................................................................................................................B–3

Warnings and Limitations................................................................................................................................................C–1

Summary of Connections........................................................................................................................Inside back cover

iii

List of Figures

•••••••••••••••••••••••••••••••••••••••••••••••••

Figure 1. Installing the Cabinet Lock ...................................................................................................................................2–1

Figure 2. Mounting the PC Board .........................................................................................................................................2–1

Figure 3. Mounting the PC Board and RF Receiver .............................................................................................................2–2

Figure 4. Using a Supplementary Power Supply .................................................................................................................2–3

Figure 5. Sounder Wiring (Supervised) ...............................................................................................................................2–4

Figure 6. Connections of 4300 Transformer to Panel ..........................................................................................................2–5

Figure 7. Wire Smoke Detector Connected to Zone 1 ..........................................................................................................2–7

Figure 9. Wiring Connections - 4219 Expansion Module .....................................................................................................2–8

Figure 10. Wiring Connections - 4229 Expansion/Relay Module ........................................................................................2–8

Figure 11. 5881/5882 RF Receiver (cover removed) .............................................................................................................2–9

Figure 12. 4204 Connections to Control Panel ...................................................................................................................2–12

Figure 13. 4285/4286 VIP Module Wiring Connections .....................................................................................................2–14

Figure 14. Connection of AAV Unit When Not Using a 4285/4286 VIP Module ..............................................................2–15

Figure 15. Connection of AAV Unit When Also Using a 4285 or 4286 VIP Module .........................................................2–15

Conventions Used In This Manual

•••••••••••••••••••••••••••••••••••••••••••••••••

Before you begin using this manual, it is important that you understand the meaning of the following symbols:

A UL note that includes specific information that must be followed if you are installing this system in a UL

Listed application.

A note that includes specific information that must be followed if you are installing this system in a Canadian

UL Listed application..

A checked note includes information you should be aware of before continuing with the installation, and

which, if not observed, could result in operational difficulties.

This symbol warns of conditions that could seriously affect the operation of the system, or cause damage to

the system. Please read each warning carefully. This symbol also denotes warnings about physical harm to

the user.

PRODUCT MODEL NUMBERS:

Unless noted otherwise, references to specific model numbers represent ADEMCO

products.

1–1

SECTION 1

Introduction

•••••••••••••••••••••••••••••••••••••••••••••••••

The VISTA-15/VISTA-15CN control with the following major features :

Features

Basic Hardwired Zones

Provides 6 basic hardwired zones having the following characteristics:

• EOLR supervision supporting N.O. or N.C. sensors

• Programmable response time (10, 350, or 700 mS)

• Up to sixteen 2-wire smoke detectors on zone 1

• 4-wire smoke or heat detectors on zones 2 through 6 (as many as can be powered from Auxiliary Power on the

control).

Optional Expansion Zones (26 total: up to 8 wired with 18 wireless, OR 26 wireless)

Wired Expansion

Supports up to 8 additional wired zones using a 4219 Expansion Module or 4229 Expansion/Relay Module. These zones

have the following characteristics:

• EOLR supervision supporting N.O. or N.C. sensors

• 300-500mS normal response with an option for fast (10-15mS) response on loop A (first expansion zone).

Wireless Expansion:

Supports up to 26 wireless zones (fewer if using wired expansion zones).

• Requires the use of a 5881 (5882 in Canada) type RF receiver,

as indicated below:

Receiver Model No. of Zones

5881L/5882L Up to 8

5881M/5882M Up to 16

5881H/5882H Up to 26

• Requires the use of 5800 Series Wireless Transmitters.

Remote Keypads

Up to 4 of any of the following keypads may be used in the installation:

Fixed-word keypad: 6128, 6128RF

Alpha keypad: 6139 (2-line alphanumeric display)

Security Codes Supported

• One Installer code for entire system (user 1)

• One Master code for entire system (user 2)

• 12 Secondary User codes (users 3–14)

• One Temporary code (user 15)

• One Duress code (user 16).

Temporary Code: A special code that can be used to disarm and arm the system until the Master code is

entered.

Duress Code: An emergency code that, when entered by

any

user to disarm or arm the system, sends a

silent duress message to the Central Station.

Keypad Panic Features

• Up to 3 programmable panic key functions provided

• Designated as zones 95, 96, 99

• Activated by wired and wireless keypads

• Distinguished by subscriber ID number.

VISTA-15/VISTA-15CN Installation and Setup Guide

1–2

Zone Monitor Features

• Provides automatic high loop resistance detection on hardwired zones 2–6, and displays a

CHECK

message for the

affected zone when the system is in the disarmed state.

• Contains a Hardwire Short Detection circuit for zones 1-6

†

, and enabled in

✱

30. Detecting a short in any wired zone,

it sends a sensor Trouble message to the Central Station when the system is in the disarmed state. At the same time

CHECK

message is displayed on the keypad.

• Hardwire Short Detection is disabled on any zone programmed for FIRE (Zone type 09).

• Either condition (high resistance or short) detected on any zone, prevents the system from being armed until the

offending condition is cleared. Conversely, when the system is armed, and these conditions occur, an alarm is

generated.

Exit Error False Alarm Prevention Features

• Enables the system to determine the difference between an actual alarm and an alarm caused by leaving an

entry/exit or interior zone open after the Exit Delay expires. If not disarmed in time, an alarm sounds and an Exit

Error report is sent to the Central Station.

• An exit alarm condition also occurs if an entry/exit or interior zone re-opens within 2 minutes after the end of an

Exit Delay.

• The system provides an automatic Exit Delay Reset feature that allows the user to exit (fault), close the door

(restore the fault), then re-enter (fault again) the premises within the exit delay time period. Upon re-entering, a

new exit delay time period is begun with the keypad annunciating three rapid beeps. This feature only resets the

exit delay time once for each arming session.

Optional Output Relays and Powerline Carrier Devices (X10 type)

The VISTA-15/VISTA-15CN supports the following optional output relays and Powerline Carrier devices (X10 type):

• Maximum of 4 output devices

• Up to 4 relays using one 4204 Relay Module

• Up to 2 relays using one 4229 Zone/Relay Module

• Up to 4 Powerline Carrier devices (you must subtract the number of relay outputs actually used by the 4204 or 4229

modules, if used).

• Actions are programmable to respond to zone activity or manual keypad entries.

Powerline Carrier devices require the use of the optional 4300 Transformer Module instead of the supplied

1321/1321CN AC Transformer.

Optional VIP Module

• The VISTA-15/VISTA-15CN supports the ADEMCO 4285/4286 VIP Module

(refer to Section 8: 4285/4286 VIP

Module for further information).

• Provides access to the system via on-premises or off-premises phones for arming, disarming, etc., plus control of

relay outputs and Powerline Carrier devices.

Paging Feature

If programmed, the paging feature allows certain system conditions to be reported to a pager. Up to 16 digits may be

programmed to be sent as a message to the pager. A 7-digit code following the programmed message indicates the type of

condition that has occurred.

Audio Alarm Verification (AAV) Option

• Provides a programmable Audio Alarm Verification (AAV) option, which can be used in conjunction with an output

relay to permit voice dialog between an operator at the Central Station and a person at the premises.

• This AAV option must be used with a relay unit, such as an Eagle Model 1250.

The AAV option may not be used in UL installations.

Optional Long Range Radio

Allows all messages that have been programmed to go to the primary telephone number to also be sent to any ECP-

operational radio (such as the 7835C, 7720PLUS, and 7820) for transmission to the Central Station.

Section 1: Introduction

1–3

Built-in Telephone Line Monitoring Option

• You can monitor telephone line voltage to supervise the phone line connection. You must connect the panel to a

proper earth ground or you will get a false line cut indication if this feature is enabled.

• The loss of the line can optionally cause a local display, or a display and trouble sound.

Event Logging

Keeps a record of up to 48 selected events in a history log. All control and readout from the log is done via ADEMCO

COMPASS software

only

Quick Arm Feature

Quick Arm may be programmed , allowing use of the [#] key in place of the security code for arming (Quick Arm will not

work unless the Master code has been programmed into the system).

Alarm Output Features

• Provides a 12VDC, 2 amp output that can drive the compatible sounders listed in

Section 9:

External Sounders

(assuming a fully charged battery is connected).

• Steady output for burglary/panic, or temporal pulse output (3 pulses – pause – 3 pulses – pause – 3 pulses . . .) for

fire.

• Uses current-limiting circuitry for protection.

• Provision for Bell supervision.

Optional Bell Supervision

Red jumper on control board, when cut, provides supervision of bell wiring (when bell is wired with EOL resistor, as

indicated in the instructions).

Chime/Chime by Zone

Chime, when on, normally sounds when any entry/exit or perimeter zone is faulted. However, a “chime by zone” option,

when programmed, allows only specific zones to chime if they are faulted when the system is in the chime mode.

Auxiliary Power Output Features

• Provides 12VDC, 600mA maximum (500mA maximum for UL installations). Uses current-limiting circuitry for

protection.

• Interrupts for smoke detector reset if 4-wire smoke detectors are used.

Programming

• Programmed options are stored in electrically erasable, nonvolatile EEPROM memory (information can be

reprogrammed at any time and will not be lost in the event of a power loss).

• The system can be uploaded, downloaded, or controlled via an IBM-compatible computer, COMPASS software, and a

modem specified by ADEMCO.

• Keypad programming consisting of:; Data field programming and Interactive (menu) mode programming.

To program from a keypad, you must connect a 6139 2-line alpha keypad, but it need not stay in the system.

Communication Formats Supported

• ADEMCO Low Speed

(Standard or Expanded)

• Sescoa/Radionics (Standard or Expanded)

• ADEMCO

Express

•

ADEMCO

Contact ID

Zone Descriptors

You can assign

alpha descriptors to all zones (only when using alpha keypads).

AC Power Supply

Uses 1321/1321CN, 110VAC plug-in transformer with 16.5VAC, 25VA output, unless Powerline Carrier devices (for

example, X10 type) are used, in which case a 4300 Transformer Module

must be used.

Backup Battery

Rechargeable (Sealed Lead Acid) 12VDC, 4AH-17.2AH. Refer to

Section 12: Final Power-Up

to calculate the actual

battery size needed.

VISTA-15/VISTA-15CN Installation and Setup Guide

1–4

2–1

SECTION 2

Mounting and Wiring the Control

•••••••••••••••••••••••••••••••••••••••••••••••••

This section describes the procedures for mounting and wiring this control and its peripheral devices. In the following

subsections, procedures are listed in the left column, while notes and pertinent explanations are provided in the right

column.

Cabinet and Lock

Notes

1. Mount the control cabininet to a sturdy wall in a

clean, dry area which is not readily accessible to

the general public using fasteners or anchors ( not

supplied) and the four cabinet mounting holes.

2. Remove cabinet door, then remove the lock

knockout from the door. Insert the key into the

lock. Position the lock in the hole, making certain

that the latch will make contact with the latch

bracket when the door is closed.

3. Insert the retainer clip into the retainer slots.

Position the clip as shown in order to permit easy

removal.

• Use an ADEMCO No. N6277 Cam Lock and No.

N6277–1 Push-On Clip (Retainer Clip).

• The cabinet can be closed and secured without a lock

by using 2 screws in the cover's edge.

CABINET DOOR BOTTOM

RETAINER

CLIP

RETAINER CLIP

(NOTE POSITION)

RETAINER

SLOTS

LOCKED

UNLOCKED

Figure 1. Installing the Cabinet Lock

Mounting the PC Board Alone

(No RF

Receiver)

Note

1. Hang two short mounting clips (provided) on the

raised cabinet tabs (see Detail B in Figure 2).

2. Insert the top of the circuit board into the slots at

the top of the cabinet. Make sure that the board

rests on the correct row (see Detail A).

3. Swing the base of the board into the mounting

clips and secure the board to the cabinet with the

accompanying screws (see Detail B).

Before installing the cabinet's contents, remove the metal

cabinet knockouts required for wiring entry. Do not

attempt to remove the knockouts after the circuit board

has been installed.

CABINET

CIRCUIT BOARD

CABINET

DETAIL B

SIDE VIEW

OF MOUNTING

CLIPS

DETAIL A

SIDE VIEW

OF BOARD

SUPPORTING

SLOTS

CIRCUIT

BOARD

V15-01-V0

Figure 2. Mounting the PC Board

VISTA-15/VISTA-15CN Installation and Setup Guide

2–2

Mounting the PC Board with RF Receiver

Notes

1. Remove the receiver board from its case, then

insert the top of the board into the slots at the top

of the cabinet, as shown in Figure 3, Detail A.

Make sure the board rests on the correct row of

tabs.

2. Swing the base of the board into the

mountingclips and secure it to the cabinet with

the accompanying screws.

3. Insert the top of the control’s board into the slot in

the clips and position two clips at the lower edge

of the board.

4. Swing this board into place nad secure with two

additional screws.

5. Insert grounding lugs (supplied with receiver)

through the top of the cabinet into the left-hand

terminals of the antenna blocks (at the upper edge

of the receiver board) and secure them to the

cabinet top with the screws provided, as shown in

Detail B.

6. Insert the receiver’s antennas through the top of

the cabinet, into the block’s right-hand terminals,

and tighten the screws.

• Do not mount the cabinet on or near metal objects.

This decreases RF range and/or block RF

transmissions from wireless transmitters.

• Do not locate the cabinet in an area of high RF

interference (revealed by frequent or prolonged

lighting of the LED in the receiver after it is

operational (random flicker is OK).

ANTENNA

MOUNT

(2 PLACES)

ANTENNA

(2)

SCREW

(2)

BLACK

MOUNTING

CLIP

RED

MOUNTING

CLIP

WHITE

MOUNTING

CLIP

GROUNDING

LUG

(2)

NOTE

A COMBINATION OF THESE MOUNTING CLIPS HAS BEEN

INCLUDED IN YOUR INSTALLATION KIT.

USE THE APPROPRIATE CLIPS FOR MOUNTING.

IF NO RF RECEIVER IS USED, MOUNT THE PC BOARD USING

EITHER THE WHITE OR BLACK CLIPS, WHICHEVER ARE

INCLUDED IN THE CONTROL PANEL'S HARDWARE KIT.

DETAIL A

SIDE VIEW

OF BOARD -

SUPPORTING SLOTS

CIRCUIT

BOARD

CABINET

MOUNTING

CLIP

CABINET

MOUNTING

CLIP

CONTROL

CIRCUIT

BOARD

SUPPORTING

SLOTS

RECEIVER CIRCUIT BOARD

pc_mount-001-V1

DETAIL B

ANTENNA AND GROUNDING

LUG INSTALLATION

INSTALLATION WITH RECEIVER CIRCUIT BOARD

Figure 3. Mounting the PC Board and RF Receiver

Section 2: Mounting and Wiring the Control

2–3

Wiring to Keypads

Notes

1. Connect keypads to the control’s keypad terminals

as shown in the Summary of Connections

diagram.

2. Determine wire gauge using the Wiring Run

Chart below.

Supplementary Power (optional)

Connect as shown. Be sure to connect the negative (–)

terminal on the power supply unit to terminal 4 (AUX –)

on the control.

–

456 7

SUPPLEMENTARY

POWER SUPPLY

–

CONTROL TERMINAL STRIP

AUX.

AUX. DATA

DATA

OUT

IMPORTANT:

MAKE THESE

CONNECTIONS

DIRECTLY TO

SCREW

TERMINALS AS

SHOWN.

TO KEYPAD RED WIRE

TO KEYPAD BLK WIRE

TO KEYPAD YEL WIRE

TO KEYPAD GRN WIRE

TO KEYPAD BLK WIRE

TO KEYPAD RED WIRE

TO KEYPAD GRN WIRE

TO KEYPAD YEL WIRE

Figure 4. Using a Supplementary Power Supply

• Fixed-Word Display: 6128, 6128RF

•

Alpha

Display

6139

• Be sure the keypads are set to the non-addressable

mode (address 31).

• Up to 4 keypads may be used in the system.

• For single 4-wire runs, determine the current drawn

by all units, then refer to the Wiring Run Chart below

to determine the maximum wire length that can be

safely used for each wire size.

• Use supplementary power if the control’s aux. Power

load for all devices exceeds 600mA.

• Suggested power supplies:

• 487-12 supplies 12V, 250mA with battery backup

• 488-12 supplies 12V, 500mA with battery backup

Use a UL Listed, battery-backed supply for UL

installations. The battery supplies power to these keypads

in case of AC power loss. The battery-backed power

supply should have enough power to supply the keypads

with the UL required minimum standby power time.

Keypads powered from supplies that do not

have a backup battery

will not function

when AC power is lost. Therefore, be sure to

power at least one keypad from the control's

auxiliary power output.

Wiring Run Chart for Devices* Drawing Aux Power from the Control (12V+ & 12V–)

TOTAL CURRENT DRAWN BY ALL DEVICES CONNECTED TO A SINGLE WIRE RUN

Wire Size

50mA or less

100mA 300mA 500mA 600mA

#22 500 ft (152m) 250 ft (76m) 80 ft (24m) 50 ft (15m) 42 ft (13m)

#20 750 ft (228.6m) 380 ft (116m) 130 ft (39.6m) 80 ft (24m) 67 ft (20.4m)

#18 1300 ft (396m) 650 ft (198m) 220 ft (67m) 130 ft (39.6m) 115 ft (35m)

#16 1500 ft (457m) 1000 ft (305m) 330 ft (100.5m) 200 ft (70m) 170 ft (52m)

* Includes Keypads, RF Receivers, Zone Expander/Relay Units, or 4285/4286 VIP Module.

Maximum wire lengths for any device that is home run to the control can also be determined from the Wiring Run Chart, based

on the current draw of that device alone

The length of all wire runs must not exceed 1500 feet (457m) when unshielded quad conductor cable is used (750 feet if

shielded cable is used). This restriction is due to the capacitive effect on the data lines when quad cable is used.

VISTA-15/VISTA-15CN Installation and Setup Guide

2–4

Sounder (Bell) Connections

Notes

1. Make sounder connections to alarm output

terminals 3 (+) and 4 (–). For supervised output,

continue with steps 2 and 3.

2. Cut the red Bell Supervision Jumper located

above terminals 2 and 3 on the control board.

3. Connect a 2k ohm resistor across the terminals of

the last sounder.

EXTERNAL ALARM

SOUNDER

TERMINALS ON

CONTROL BOARD

ALARM

OUTPUT

TERMINALS

V15-011-V0

CUT RED JUMPER ON CONTROL

BOARD TO ENABLE BELL

(SOUNDER) SUPERVISION.

2000

OHM

EOL

RESISTOR

IF BELL SUPERVISION IS ENABLED

(RED JUMPER ON CONTROL BOARD IS CUT),

CONNECT A 2000 OHM RESISTOR ACROSS THE

EXTERNAL SOUNDER AS SHOWN BY THE

DOTTED LINE.

DO NOT CONNECT THE RESISTOR AT THE

ALARM OUTPUT TERMINALS THEMSELVES!

OBSERVE

POLARITY

Figure 5. Sounder Wiring (Supervised)

This control complies with NFPA requirements for

temporal pulse sounding of the notification appliances.

Temporal pulse sounding for a fire alarm consists of: 3

pulses – pause –3 pulses – pause –3 pulses –etc.

• The 12VDC sounder output activates when an alarm

occurs.

• Total current drawn from this output cannot exceed 2

A (going beyond 2 A will overload the power supply, or

may cause the electronic circuit protecting the sounder

output to trip).

• You must install a battery, since the battery supplies

this current.

• Use only UL Listed sounding devices for UL

installations.

• Bell supervision is required for fire alarm

installations.

• The total current drawn from the alarm output and

the auxiliary power output, combined, cannot

exceed 600 mA. In addition, the sounding device

must be a UL Listed audible signal appliance rated

to operate in a 10.2-13.8 VDC voltage range, and

must be mounted indoors.

Section 2: Mounting and Wiring the Control

2–5

Wiring the AC Transformer

Notes

1321/1321CN Transformer

Connect the 1321/1321CN Transformer to terminals 1 and

2 on the control board. See wiring table at the right for

wire gauge to use.

4300 Transformer

(required If Using Powerline Carrier devices)

1. Connect terminals

1, 3 (AC), and 2 (Ground) to control

board terminals 1, 2, and 25, respectively (see

Figure 5

See wiring

table

at the right for wire gauge to use.

2. Wire the other three terminals (Sync, Data, Com) on

the 4300 Transformer. Wires from these terminals must

be connected to a 9-pin connector on the control board

(using a

4142TR Cable

supplied with the 4300

Transformer), as shown In

Figure 5

. These particular

wires can be 24-gauge or larger, and can be run along with

the AC and ground wires to the control panel.

123456789

9-PIN CONNECTOR

ON CONTROL BOARD

BLACK

BLUE

BROWN

GREEN

RED

WHITE

YELLOW

GRAY

VIOLET

4142TR CABLE

125 2

Earth

Ground

Sync

Data

Com

4300 TRANSFORMER/INTERFACE

TERMINALS

ON CONTROL

BOARD

Figure 6. Connections of 4300 Transformer to Panel

• Use caution when wiring the transformer to the

control panel to guard against blowing the fuse inside

the transformer (the fuse is nonreplaceable).

• Wiring to the AC transformer must not exceed 250

feet using 16-gauge wire. The voltage reading between

terminals 1 and 2 of the control must not fall below

16.5VAC, or an

AC LOSS

message is displayed.

• Do not plug the transformer into the AC outlet while

making any wiring connections to the control. As a

safety precaution, always power down the control

when making such connections.

Wirng Table

Distance from control Wire Gauge

Up to 50 feet #20

50 to 100 feet #18

100 to 250 feet #16

Backup Battery

Notes

Place the 12-volt backup battery in the control

cabinet.

After all connections to the control are completed,

connet the red and black flying leads on the

control board to the battery. Do not attach these

leads to the battery terminals until all

connections are completed.

Use a 4AH battery or larger for UL installations.

Refer to chart below to calculate the actual battery size

needed.

Table 1.

Auxiliary Device Current Draw Worksheet

DEVICE CURRENT # UNITS TOTAL CURRENT

6128 Keypad 30mA

6139 Keypad 100mA

5881/5882 RF Receiver 35mA

4219 Zone Expander 35mA

4204 Relay Unit

15/180mA

‡

4229 Zone Expander/Relay Unit

35/100mA

‡

4285 VIP Module 160mA

4286 VIP Module 300mA

TOTAL =

Current available from Aux. terminals = 600mA max (500mA max for UL installations)**

* If you are using hardwire devices such as PIRs, refer to the specifications for that particular unit's current draw.

VISTA-15/VISTA-15CN Installation and Setup Guide

2–6

** In UL installations, maximum current draw from the Auxiliary Output and the Alarm Output

combined

must not exceed

600mA.

‡

Figures are for relays OFF/relays ON.

Earth Ground

Notes

Metal Cold Water Pipe

Use a noncorrosive metal strap (copper is recommended)

firmly secured to the pipe to which the ground lead is

electrically connected and secured.

AC Power Outlet Ground:

Available from 3-prong, 120VAC, power outlets only. To

test the integrity of the ground terminal, use a 3-wire

circuit tester with neon lamp indicators, such as the

Listed

Ideal Model 61-035

, or equivalent, available at most

electrical supply stores.

The designated earth ground terminal (25) must be

terminated in a good earth ground for the lightning

transient protective devices in this product to be effective.

The examples of good earth grounds listed at the left are

available at most installations.

Section 2: Mounting and Wiring the Control

2–7

Hardwire Zones

Notes

Wiring Burglary and Panic Devices to Zones 1–6

1. Connect sensors/contacts to the hardwired zone terminals

(8 through 17).

2. Connect closed-circuit devices in series in the high (+) side

loop. The EOL resistor must be connected in

series

with the

devices, following the last device.

3. Connect open-circuit devices in parallel across the loop.

The 2000-ohm EOLR must be connected

across

the loop

wires at the last device.

Wiring 2-Wire Smoke Detectors to Zone 1

1. Connect 2-wire smoke detectors across zone 1 terminals 8

(+) and 9 (–). Observe proper polarity when connecting the

detectors.

2. If an

EOL resistor

is presently connected across zone 1

terminals, remove it.

The EOL resistor must be

connected across the loop wires at the last detector.

ZONE 1

2-WIRE SMOKE

DETECTOR

UL NOTE:

IN UL INSTALLATIONS, ONLY ZONE 1

MAY BE USED FOR FIRE.

SMOKE

2000 OHMS

2k EOLR

Figure 7. Wire Smoke Detector Connected to Zone 1

• If the EOLR is not at the end of the loop, the zone

will not be properly supervised, and the system

may not respond to an open-circuit on the zone.

• The alarm current provided by zone 1 supports only

one smoke detector in the alarmed state.

In UL installations, only zone 1 may be used as

a fire zone. In addition, an ADEMCO Model 610–7 must

be used as the end-of-line resistor at the last detector.

COMPATIBLE 2-WIRE SMOKE DETECTORS

Detector Type System Sensor

Model No.

Photoelectric w/heat sensor, direct

wire

2300TB, 2400TH

Photoelectric, direct wire 2400

Photoelectric 2451 w/B401B base

Photoelectric w/heat sensor 2451TH w/B401B

base

Ionization, direct wire 1400

Ionization 1451 w/B401B base

Photoelectric duct detector 2451 w/DH400 base

Ionization duct detector 1451D w/DH400

base H

Low-profile, photoelectric, w/135°F

thermal

2100T

Low-profile, ionization type, direct wire 1100

Wiring 4-Wire Smoke/Combustion Detectors on Zones

2-6

1. Connect 12-volt power for the detectors from Auxiliary

Power terminals 4 and 5 (which interrupts power for fire

alarm reset). Observe proper polarity when connecting

detectors.

2. Connect detectors (including heat detectors, if used) across

terminals of the zone selected (zones 2-6 may be used). All

detectors must be wired in parallel.

2000

OHMS

EOLR

HEAT

DETECTOR

HEAT

DETECTOR

ZONES 2-6

RED

EOL

POWER

SUPERVISION

RELAY MODULE

A77-716B

VIOLET

4-WIRE SMOKE

OR COMBUSTION

DETECTORS

TO HI SIDE OF

SELECTED

TO LO SIDE OF

SELECTED

AUX PWR

OUTPUT

TERMINALS

BLK

Figure 8. Wire Smoke Detector Connections (Zones 2–6

)

• Remove 2000 ohm EOL resistor if connected across

the selected zone terminals. You must connect the

EOL resistor across the loop wires at the last

detector.

•

To supervise power, we recommend the use of a

System Sensor

No. A77-716B

Supervisory Module.

Compatible 4-Wire Smoke/Combustion

Detectors

System Sensor

1412

4-wire ionization products of

combustion detector

System Sensor

2412

4-wire photoelectric smoke

detector

System Sensor

2412TH

4-wire photoelectric smoke

detector w/135

F (57

C) heat

detector

System Sensor

A77716B

EOL relay module (supervisory

module for wired 4-wire fire zone).

System Sensor

2112/24T

low-profile 4-wire photoelectric

smoke detector w/135

F (57

heat detector

VISTA-15/VISTA-15CN Installation and Setup Guide

2–8

4219/4229 Expansion Zones

Notes

1. Connect the module to the control's keypad terminals.

2 .

Set the 4219 or 4229's

DIP switch

for device

address

“1” (switch 2 in the OFF position and switches 3, 4, 5 in the

ON position). Switch 1 determines expansion zone A's

response time (ON = normal response, OFF = fast

response).

• You can add 8 wired EOLR zones to the basic control's

6 zones, for a total of 14 wired zones, by using a 4219

Wired Expansion Unit or 4229 Wired Expansion/Relay

Unit.

•

Connected a 1000 ohm

EOL resistor

across the

terminals of unused expansion zones on the

4219

4229

Module).

4219

GRN

BLK

(–) GROUND

RED

(+) 12VDC

YEL

ZONES

TAMPER JUMPER

POSITION IN CABINET

(NOT TAMPER PROTECTED)

REMOTE

TAMPER PROTECTED

TB1

TB2

4-PIN CONSOLE PLUG

(CONNECTIONS SAME AS TB2)

DATA OUT

TO CONTROL

DATA IN FROM

CONTROL

TERMINATE EACH PROGRAMMED

ZONE WITH 1000 OHM (1K)

END-OF-LINE RESISTOR

(EACH ZONE'S LOOP RESISTANCE:

300 OHMS + EOL)

REED

(TAMPER)

SWITCH

4 6

DIP SWITCH FOR SETTING

ADDRESS AND ZONE A

RESPONSE TIME

Figure 9. Wiring Connections - 4219 Expansion Module

BRN

GRN

BLK

(–) GROUND

RED

(+) 12VDC

YEL

ZONES

DIP SWITCH FOR SETTING

ADDRESS AND ZONE A

RESPONSE TIME

TAMPER JUMPER

POSITION IN CABINET

(NOT TAMPER PROTECTED)

REMOTE

TAMPER PROTECTED

TB1

4229

TB2

WHT

GRY

VIO

BLK

YEL

ORG

GND

RLY

RELAYS SHOWN

DE-ENERGIZED

RELAY

CONNECTOR

RELAY

(TERM 6)

(TERM 4)

(TERM 5)

(TERM 7)

NO C NC

TERMINALS ON

CONTROL PANEL

DATA OUT

TO CONTROL

DATA IN FROM

CONTROL

REED

(TAMPER)

SWITCH

4 6

TERMINATE EACH PROGRAMMED

ZONE WITH 1000 OHM (1K)

END-OF-LINE RESISTOR

(EACH ZONE'S LOOP RESISTANCE:

300 OHMS + EOL)

4229 ADDRESS SETTINGS

SWITCH

NUMBER

("—" means "OFF")

123456789101112131415

ON — ON — ON — ON — ON — ON — ON — ON —

ON ON — — ON ON — — ON ON — — ON ON — —

ON ON ON ON — — — — ON ON ON ON — — — —

ON ON ON ON ON ON ON ON — — — — — — — —

12345

➞

OFF ON

4-PIN

CONSOLE

PLUG

EITHER OR BOTH

CAN BE USED

SWITCH SHOWN

FOR ADDRESS "0"

Figure 10. Wiring Connections - 4229 Expansion/Relay Module

Section 2: Mounting and Wiring the Control

2–9

Installing the RF Receiver

Notes

1. Set the receiver's DIP switch for device address “00”, as

described in its instructions (all switches to the left, the

“off” position).

2. Mount the receiver noting that the RF receiver can

detect signals from transmitters within a nominal range of

200 feet.

3. Connect the receiver's wire harness to the control's

keypad terminals. Plug the connector at the other end of

the harness into the receiver. Refer to the installation

instructions provided with the receiver for further

installation procedures regarding antenna mounting, etc.

• You must use one of the following receivers:

RF Receiver No.of Zones

5881L/5882L Up to 8

5881M/5882M Up to 16

5881H/5882H Up to 26

• If you are using a 5804BD, 5827, or 5827BD Wireless

Keypad with the system, you must program a House

ID Code (01-31) in field

✱

24 to establish proper

communication, and the keypad must be set to the

same ID. House ID 00 disables all wireless keypads.

Note the following if the receiver is mounted remotely.

• Place the RF receiver in a high, centrally located area

for best reception.

•

Do not locate the receiver or transmitters on or near

metal objects. This decreases range and/or block

transmissions.

•

Do not locate the receiver in an area of high

interference (revealed by frequent or prolonged

lighting of the LED in the receiver; random flicker is

OK).

• The RF receiver must be at least 10 feet from any

remote keypads to avoid interference from the

microprocessors in those units.

MOUNTING

HOLES

INTERFERENCE

INDICATOR

LED

CIRCUIT BOARD

DIP

SWITCH

ANTENNAS

(INSERT IN

RIGHT-HAND

TERMINALS)

YELLOW

RED

BLACK

GREEN

WIRING OPENING

KNOCKOUT AREA

FOR SURFACE WIRING

TO CONTROL'S

REMOTE KEYPAD

CONNECTION

POINTS.

5882

LOCATION

TO RELEASE CIRCUIT BOARD,

REMOVE SCREWS AND

BEND BACK TABS

NOTE

CIRCUIT BOARD IS MOUNTED IN

CONTROL'S CABINET. GROUNDING

LUGS (2) PROVIDED

MUST

BE INSERTED

IN LEFT-HAND TERMINALS OF ANTENNA

BLOCKS AND SECURED TO CABINET.

(SEE RECEIVER'S AND CONTROL'S

INSTRUCTIONS)

SOCKET

PLUG

MODEL NO. IS INDICATED ON CIRCUIT BOARD

5881-003-V0

Figure 11. 5881/5882 RF Receiver (cover removed)

Installing a 5800TM Module

Notes

1. Mount the 5800TM next to the RF receiver (between 1

and 2 feet from the receiver’s antennas) using its

accompanying mounting brackets. Do not install within

the control cabinet.

2. Connect the 5800TM to the control panel’s keypad

connection terminals as shown on the Summary of

Connections diagram.

3. For additional information refer to the 5800TM’s

instructions.

• Use this module is necessary only if you are using one

or more 5827BD Wireless Bi-directional Keypads,

5804 or 5804BD Transmitters (wireless keys).

• Do not cut any of the jumpers on the 5800TM when

using it with the VISTA-15/VISTA-15CN.

VISTA-15/VISTA-15CN Installation and Setup Guide

2–10

Installing the Transmitters

Notes

1. To be sure of the transmitter’s signal at the

proposed mounting location is adequate, perform

a Go/No Go Test, described in the

Testing the

System

section.

2. Install transmitters in accordance with the

instructions provided with each.

3. Set 5827 transmitters to the programmed House

ID, using its DIP switches.

• Refer to the table of compatible devices at the back of

this manual.

The 5802MN, 5802MN2, 5804, 5804BD, 5814,

5816TEMP, 5819, 5819S(WHS & BRS), 5827BD, and

5850 transmitters are not intended for use in UL

installations.

Transmitter Battery Life

• Batteries in the wireless transmitters may last from 4 to 7 years, depending on the environment, usage, and the

specific wireless device being used. Factors such as humidity, extreme temperatures, as well as large

temperature variations may all reduce the actual battery life in a given installation.

• The wireless system can identify a true low-battery situation, thus allowing the dealer or user of the system time

to arrange a change of battery and maintain protection for that given point within the system.

• Some transmitters (e.g., 5802, 5802CP, and 5804) contain long-life but nonreplaceable batteries, and no battery

installation is required. At the end of their life, the complete unit must be replaced (and a new serial number

enrolled by the control).

• Button-type transmitters (such as 5801, 5802, 5802MN/MN2, 5802CP, and 5804) should be periodically tested for

battery life.

• The 5802MN and 5804 Button Transmitters have replaceable batteries.

Do not install batteries in wireless transmitters until you are ready to enroll the transmitters during system

programming. After enrolling, batteries need not be removed.

Jam Detection and Reporting

When field

✱

22, option 4 (in Data Field Descriptions) is selected, a 5800 series receiver detecting a jam condition sends

E344

(RF Receiver Jam Detect) Contact ID report to the Central Station. At the same time, a

Rcvr Jam

(alpha

keypads) or

CHECK 90

(fixed-word keypads) message alternates with the present system message on the keypad. When

the jam condition is cleared, a

Restore

message is sent to the CS. Entering a code and OFF restores the keypad display.

The default for this option is 0 (disabled).

Normal use of a 5827 wireless keypad may cause a false RF jam message to be displayed in system

that have been programmed for RF Jam Detection.

About 5800 Series Transmitters

Programming Wireless Zones

5800 Series transmitters have built-in serial numbers that you must “enroll” into the system using the

✱

56 or

✱

58 Zone

Programming mode, or input to the control via the downloader. 5800 Series transmitters (except 5827, described

separately) do not have DIP switches.

Program each transmitter's zone number into the system using

✱

56 or

✱

58 mode (see

Section 16: Zone

Programming

). Some transmitters, such as the 5816 and 5817, can support more than one “zone” (referred to as loops

or inputs). On the 5816, for example, the wire connection terminal block is loop 1, the reed contact is loop 2. Each loop

must be assigned a different zone number.

The 5816 and 5817 transmitters do not have EOL supervision of their loop wiring. Therefore, for UL

Household Burglary installations, the loop wiring may not exceed 3 feet.

For button transmitters (RF “keys”), such as the 5801, 5804, and 5804BD, you must assign a unique zone number to

each individual button used on the transmitter. Each button on the transmitter also has a predesignated loop or input

number, which is automatically displayed on the keypad.

La pagina sta caricando ...

ADEMCO Security System VISTA-15CN Installation And Setup Manual

Marca: ADEMCO

Modello: Security System VISTA-15CN

Categoria: Sistemi di controllo accessi di sicurezza

Tipo: Installation And Setup Manual

Questo manuale è adatto anche per

Security System VISTA-15

Scarica il pdf

rapporto

in altre lingue

English: ADEMCO Security System VISTA-15CN

ADEMCO Security System VISTA-15CN Installation And Setup Manual

Questo manuale è adatto anche per

ADEMCO Security System VISTA-15CN Installation And Setup Manual

in altre lingue

Documenti correlati

Altri documenti