Gold Note A6 EVO II Manuale utente

USER

MANUAL

A6 EVO II

EN

DE

IT

Thank you for purchasing one of our units

and welcome into the Gold Note world,

where we turn High-End audio and music

into a new experience.

Maurizio Aterini,

founder of Gold Note

EN

DE

IT

|

IMPORTANT SAFETY

| INFORMATIONS

the third prong are provided for your safety.

If the provided plug does not fit into

your outlet, consult an electrician for

replacement of the obsolete outlet. or

pinched particularly at plugs, convenience

receptacles, and the point where they exit

from the apparatus.

|Only use attachments/accessories specied

by the manufacturer.

|Use only with the cart, stand, tripod,

bracket, or table specied by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

|Unplug this apparatus during lightning

storms or when unused for long periods

of time. Refer all servicing to qualied

service personnel only. Servicing is required

when the apparatus has been damaged in

any way (such as when the power cord or

plug is damaged, liquid has been spilled

or objects have fallen into the apparatus,

the apparatus has been exposed to rain

or moisture) and in any case when the

apparatus does not operate normally or

has been dropped.

PLEASE NOTE

1 Do not disassemble any part of the

product.

2 Do not use any part of the product for

other purposes.

3 For service and problems of any kind,

contact qualified Gold Note personnel.

4 Protect the product from rain, humidity

and keep away from heat sources, electric

and electronic motors etc. The power

cord supplied must be used only on this

unit.

5 Gold Note does not have responsibility

for any improper use of this unit.

GENERIC INFORMATION

|Read these instructions and store them.

|Heed all warnings.

|Follow the instructions.

|Do not use this apparatus near water.

|Clean only with a dry cloth.

|Do not block the ventilation openings

and install in accordance with the

manufacturer’s instructions.

|Do not install near heat sources such as

radiators, heat registers, stoves or other

apparatus (including ampliers) that

produce heat.

|Do not defeat the safety purpose of

the polarised or grounding-type plug: a

polarised plug hastwo blades with one

wider than the other.

|A grounding type plug has two blades and

a third grounding prong. The wide blade or

EN

DE

IT

This appliance has a serial number located on the rear panel.

Please record the model and serial number and retain them for your records.

MODEL

SERIAL NUMBER

CAUTION!

To reduce the risk of electric shock, do not

remove cover (or back). No user-serviceable

parts inside. Refer only to qualified Gold

Note service personnel for service.

WARNING!

To prevent fire or shock hazard, do not

expose this appliance to rain or moisture.

GOLD NOTE - Information on the correct management of waste from

household Equipment pursuant to the European Directive 2012/19/EU

The crossed-out wheelie bin symbol shown on the equipment or its packaging indicates

that the product, at the end of its useful life, must be collected separately from other waste

to allow its proper treatment and recycling. The user must therefore deliver, free of charge,

the end-of-life equipment to the centres for the separate collection of waste electrical and

electronic equipment, or return it to the dealer in accordance with the procedures established

by the legislation.

The appropriate separate collection of discarded equipment allows for proper recycling,

treatment and environmentally compatible disposal, helping to avoid the possible dispersion

of hazardous substances and negative effects on the environment and health, favouring

the reuse and/or recycling of the materials of which the equipment is composed of. Illegal

dumping of the product by the user involves the application of administrative sanction

provided for by the legislation in force. We invite you consult the current legislation and the

measures adopted by the public service operating in your country or territory.

| INDEX

| PACKAGE CONTENT

INTRODUCTION AND FEATURES 1

TECHNICAL SPECIFICATIONS 2

ASSEMBLING THE STAND 3

CONNECTING THE LOUDSPEAKERS 4

POSITIONING THE LOUDSPEAKERS 5

LOUDSPEAKERS SETUP 7

PRODUCT REGISTRATION 8

TROUBLESHOOTING 9

RELATED PRODUCTS 10

2x

A6 EVO II

2x

LOUDSPEAKER

GRILLES

8x

SPIKE FEET

1x

ALLEN KEY

4x

M4x20mm

SCREWS

with washers

8x

SPIKE PADS

8x

M4x35mm

SCREWS

with washers

1x

USER

MANUAL

EN

DE

IT

| INTRODUCTION AND FEATURES

The A6 EVO II is a three-way floor-standing

loudspeaker with rear bass reflex design

featuring a 6” internal sub-woofer, 2 x 5.5”

mid-woofers and a 1.1” dome tweeter in

silk. This compact but extremely powerful

loudspeaker provides a naturally smooth

sound, complemented by the distinctive

beauty of the unique diamond design.

From the cabinet to the drivers, this

loudspeaker is entirely made in Italy by

local suppliers and craftsmen to deliver the

highest quality in terms of sound, design

and materials. The crossover is developed

with audio-grade components to match the

unique characteristics of the drivers and

deliver exceptionally powerful responses

across the entire frequency spectrum,

achieving a most natural and dynamic sound.

The drivers are supported by extra-rigid

flanges in aluminum and the silk dome

ensures ultra-clean high frequencies with a

noteworthy extension thanks to its powerful

magnet. A premium material such as

aluminium is used to support the drivers and

for the rear reflex ports.

To provide an exceptionally fast transient

response and retain its natural sound quality,

the two mid-bass drivers have a 12dB/

Octave set up at 2000Hz/70Hz range.

An internal 6” subwoofer is located in a

dedicated sealed chamber in the lower

part of the cabinet, featuring a dedicated

crossover network and bass reflex port facing

downwards for perfect control over the lower

frequencies down to 40Hz. The custom 1”

silk dome tweeter is fine-tuned to match the

cabinet shape and size, delivering crystal

clear high frequencies.

1

To increase the rigidity of the structure,

the cabinet is made of hardened HDF

and reinforced with beautiful side panels

featuring our exclusive diamond design.

Luxurious finishes are used for the cabinet

and the side panels, a statement of true

Italian craftsmanship. The A6 EVO II

combines elegance, performance and audio

pleasure in unconventional ways to satisfy

even the most demanding audiophiles.

2

MAIN FEATURES

|3 way design with rear bass reex port

|Frequency response:

40-20000Hz ±3dB

|Sensitivity:

88dB SPL 2,83V/1m

|Nominal Impedance:

4Ω

|Tweeter:

1.1” dome driver

|Mid-woofer:

5,5” cone driver

|Sub-woofer:

6” cone driver

|Suggested power amplier:

min. 20W

|Max power handling:

150W RMS

|Crossover:

70Hz and 2000Hz @ 12dB/Oct.

|Connectors:

Gold Note gold plated nickel-free

DIMENSIONS AND WEIGHT

Dimensions:

290mm W x 1075mm H x 445mm D

Weight:

Kg. 60/pr. net

Kg. 80/pr. boxed

KEY FEATURES

|6” cone sub-woofer

|2x 5.5” cone mid-woofer

|1.1” silk dome tweeter

|2x aluminium rear bass reex ports

| TECHNICAL SPECIFICATIONS EN

DE

IT

STEP 1

Carefully place the loudspeaker upside

down or alternatively lay it horizontally on

a table to assemble the stand, covering the

supporting surface with a soft cloth to avoid

scratches and other damages to the cabinet.

To lift the loudspeaker, you can use the bass

reex port as a lifting point but pay attention

to avoid damaging the drivers.

STEP 2

Insert the spike feet into the 4 holes on the

base as shown in the picture below and

tighten them rmly to lock them in place.

STEP 3

Insert the M4x35 screws into the 4 outer

holes and rmly tighten them to join the

base.

STEP 4

Insert the M4x20 screws into the 2 central

holes and rmly tighten them to join the

base.

| ASSEMBLING THE STAND

3

STEP 5

Turn the loudspeaker upside down to

place the base on the ground ensuring the

spike feet sit on the spike pads to prevent

damages to the oor.

IMPORTANT

Please pay attention to the screws and

ensure you are using the correct type for

each step.

M4x35

M4x20

Spike feet

EXAMPLE CONNECTION

|

CONNECTING THE

| LOUDSPEAKERS

4

EN

DE

IT

STEREO POWER AMPLIFIER

A6 EVO II

RIGHT LEFT

A6 EVO II

|

POSITIONING THE

| LOUDSPEAKERS

5

The dimensions of your listening room don’t

have as much of an effect on the audio

quality as the position of the loudspeakers so

we recommend placing them carefully. The

better the positioning, the better the focus

and the sound stage will be.

Managing reective surfaces is a key factor

to get the best out of your loudspeakers,

especially because the sound waves carry

enough energy to bounce off surfaces twice,

affecting the sound performance of the

system greatly.

Depending on the size of the room and

the materials, the rst reection can create

a 25m/s delay disturbing the sound.

Reections creating delays between 40 and

80m/s are less important as they contribute

to creating the so-called ambience.

Therefore it is very important to mitigate

reections resulting in 25m/s delays.

We recommend placing the loudspeakers

as far as possible from the sidewalls

and covering the oor in front of them

with carpets if possible. Ensuring the

loudspeakers are located at the same

distance from the walls to the sides as the

one at the back (symmetrical layout) can be

highly benecial.

WALL MATERIAL

Thick walls provide good control over the

bass extension as well as acoustic insulation.

Dry and thin walls can vibrate, therefore

they are usually to be avoided or treated

accordingly.

CEILING

High ceilings tend to offer better results, with

an ideal constant height of 2,50m to 3,60m.

Vaulted ceilings can be difcult to deal with

as they act as a magnier lens for specic

frequencies.

If the ceiling is not at but at an angle, we

recommend to position the loudspeakers

closer to the side where the ceiling is lower

while the listening point should be where the

ceiling is higher.

FLOOR

Marble and hard-stone oors are difcult to

manage due to the reections they create.

Carpeted oors can also prove difcult

because of how they absorb the sound

waves. Wooden oors tend to perform well

in most cases.

In any case, oors can be easily treated with

a 2/4cm thick carpet placed in front of the

loudspeakers.

SIDE WALLS

You should avoid naked side walls around

the system as well as hanging carpets.

Hanging objects, such as framed pictures

and paintings, are usually okay if they

come without glass protections and are

located symmetrically on both sides of the

loudspeakers. Treating the walls with wall

sound traps and diffusers tends to give the

best results.

6

EN

DE

IT

REAR WALL

The rear wall is generally to be treated as the

sidewalls, taking measures to facilitate sound

diffraction using sound traps or diffusers

(such as bookshelves, bookcases and record

racks).

OPPOSITE WALL

If your listening room is small in size and the

system is too close to the opposite wall, it’s

worth considering treating the wall with thick

curtains or other diffusers.

WINDOWS AND DOORS

Windows and doors will most likely produce

vibrations when the music is playing. It’s

best to avoid rooms with windows, doors

and other glass surfaces in corners or at the

center of the side walls. If that’s not possible,

treatment should be applied to prevent

overwhelming reections. If using curtains,

it’s recommended to opt for lighter materials

to allow some of the sound waves to travel

through it and bounce off the surface.

FURNITURE

Avoid furniture with a large quantity of

glass and/or doors and drawers. Open shelf

furniture usually works quite well. If possible,

avoid placing racks and at surfaces between

the loudspeakers and the listening point as

they might reect heavily the high and mid-

frequencies.

AUDIO RACKS

Audio racks are greatly inuenced by their

design and the material used so, depending

on these factors, it might be best to place

them between the speakers or to the side

of the system. The Gold Note Galileo

rack features a special curved design to

effectively diffracting the sound waves

and can therefore be placed between the

loudspeakers.

SUBWOOFER

Subwoofers generate sound waves that

behave similarly to the waves created by

the loudspeakers so they should be placed

keeping in mind the principles listed here.

7

If this is not possible, then it’s crucially

important to adjust the position and angle

of the loudspeaker to find the preferred

balance between a wide soundstage and

focussed sharp details.

If possible, try to follow these rules to place

the loudspeakers in their initial setup. From

here, you can then perform listening tests to

fine-tune the position of each loudspeaker

and improve the focus and soundstage

perceived from the listening point.

The distance between the loudspeakers and

the listening point should be approximately

the same as shown in the picture below. In

the same way, the distance between each

loudspeaker and the closer sidewall should

be approximately the same as the distance

between them and the back wall.

Listening point

A6 EVO IIA6 EVO II

Loudspeakers distance

| LOUDSPEAKERS SETUP

8

EN

DE

IT

| PRODUCT REGISTRATION

PRODUCT REGISTRATION

We recommend to register the unit on our

internet website within 15 days from the

purchase at

www.goldnote.it/product-registration

If the unit is not registered correctly or has

been purchased from a different country of

the purchaser home address the unit will

not be covered by any warranty and the

registration will be refused.

Please note that the warranty does not cover

in any case: Tubes, Phono Cartridge Stylus

and Batteries.

WARRANTY

All Gold Note products come with a

warranty against defective materials and

workmanship.

Any service and inspection must be carried

out by a Gold Note dealer or distributor so

in case you need any assistance with this

product, please contact the seller.

If you experience any problems locating

your official Gold Note dealer or distributor,

please check our website or contact

[email protected]

PLEASE NOTE

Descriptions and technical characteristics

may vary at any time and without notice.

If you have any questions contact us at:

[email protected]

WARNING

Gold Note products should only be

opened, serviced and inspected by certified

Gold Note technicians and dealers. Work

performed by unqualified personnel may

cause serious damage or personal injury.

Opening of the product by non-authorised

personnel will void the guarantee.

In this case, contact your dealer to be

advised on how the fault can be solved.

Do not return any object directly to the

factory or to the distributor without being

authorised to do so.

www.goldnote.it/product-

registration

9

| TROUBLESHOOTING

PROBLEM CAUSE SOLUTION

The loudspeakers make a

humming noise.

The music is out of phase.

One or more drivers are

not working.

|The loudspeakers are not

correctly grounded.

|The speaker terminals

(negative/positive poles)

are inverted on the amp

or on the speaker.

|The bridges are not well

connected to the speaker

terminals (binding posts).

|The speaker cables are

not well connected to the

speaker.

|The amplier or the

sources are not working

correctly.

|Check that the system

and the rest of the room

is grounded correctly.

|Switch completely off the

amplier, then connect

the speaker cables

correctly.

|Check that the bridges

are well connected.

|Check that the cables are

well connected.

|Check that all the

components of the

system are working and

correctly wired.

|The interconnect input

and/or output cables are

not shielded.

|Always use shielded

cables.

CLEANING THE UNIT

With EXTREME care use ONLY water or detergents for delicate surfaces with a very soft

cloth to sweep dust and remove stains.

Any acid or not extremely soft cloth will irreversibly damage the unit. Do not use alcohol.

10

EN

DE

IT

| RELATED PRODUCTS

INTEGRATED AMPLIFIER

|IS-1000

Class-A/B streaming integrated amplifier

delivering 125Watt @ 8Ω per ch. with High-

Current Mosfet technology. Features UPnP

streamer, BurrBrown PCM1796 DAC, MM/

MC phono stage.

POWER AMPLIFIER

|PA-1175 MKII

Class-A/B power amplifier with variable

Damping Factor technology for a perfect

match with all types of loudspeakers.

Discover more on our website

www.goldnote.it

11

Vielen Dank, dass Sie sich für eines unserer

Geräte entschieden haben und herzlich

Willkommen in der Welt von Gold Note, wo

wir High-End Audio und Musik in eine neue

Erfahrung verwandeln.

Maurizio Aterini,

Gründer von Gold Note

12

EN

DE

IT

|

WICHTIGE

| SICHERHEITSHINWEISE

BITTE BEACHTEN

1 Nehmen Sie das Gerät nicht auseinander.

2 Verwenden Sie das Gerät oder Teile

davon nicht für einen anderen als den

vorgesehenen Zweck.

3 Für Reparaturen und Probleme jeglicher

Art wenden Sie sich bitte an den Gold

Note Fachhändler.

4 Schützen Sie das Produkt vor Nässe

und Feuchtigkeit und halten Sie es

fern von Wärmequellen, elektrischen

und elektronischen Motoren, usw. Das

mitgelieferte Netzkabel darf nur an

diesem Gerät verwendet werden.

5 Gold Note übernimmt keine

Verantwortung für Schäden durch

unsachgemäße Handhabung.

13

ALLGEMEINE HINWEISE

|Lesen und verwahren Sie diese Anleitung.

|Beachten Sie alle Warnungen.

|Befolgen Sie alle Anweisungen.

|Verwenden Sie dieses Gerät nicht in der

Nähe von Wasser.

|Reinigen Sie das Gerät nur mit einem

trockenen Tuch.

|Blockieren Sie keine Lüftungsöffnungen.

Installieren Sie das Gerät gemäß den

Anweisungen des Herstellers.

|Installieren Sie das Gerät nicht in der

Nähe von Wärmequellen wie Heizkörpern,

Heizregistern, Öfen oder anderen Geräten

(einschließlich Verstärkern), die Wärme

erzeugen.

|Die Sicherheitsfunktion des gepolten

oder geerdeten Steckers darf nicht

beeinträchtigt werden. Ein polarisierter

Stecker hat zwei Blätter, von denen einer

breiter als der andere ist. Ein geerdeter

Stecker hat zwei Klingen und einen dritten

Erdungsstift. Die breite Klinge oder der

dritte Zinken dienen Ihrer Sicherheit. Wenn

der mitgelieferte Stecker nicht in Ihre

Steckdose passt, wenden Sie sich an einen

Elektriker, um die veraltete Steckdose

auszutauschen.

|Schützen Sie das Netzkabel vor

unbefugtem Betreten oder Quetschungen,

insbesondere an Steckern, Steckdosen und

an der Stelle, an der sie aus dem Gerät

austreten.

|Verwenden Sie nur die vom Hersteller

angegebenen Anbaugeräte/Zubehörteile.

|Verwenden Sie das Gerät nur mit dem

vom Hersteller angegebenen oder mit

dem Gerät verkauften Wagen, Ständer,

Stativ, Halter oder Tisch. Wenn ein Wagen

benutzt wird, seien Sie vorsichtig, wenn Sie

die Kombination Wagen/Gerät bewegen,

um Verletzungen durch Umkippen zu

vermeiden.

|Das Gerät soll bei Gewitter oder längerer

Nichtbenutzung vom Netz getrennt

werden.

|Die Wartungsarbeiten und Reparaturen

nur von qualizierten Fachpersonal des

Kundendienst ausführen lassen. Das Gerät

zum Kundendienst bringen, wenn es Regen

oder Feuchtigkeit ausgesetzt war, wenn

Flüssigkeit oder Fremdkörper hineingelangt

sind, wenn es heruntergefallen ist oder

nicht normal funktioniert, oder wenn das

Netzkabel beschädigt ist.

La pagina sta caricando ...

Gold Note A6 EVO II Manuale utente

Gold Note A6 EVO II Manuale utente

in altre lingue

Documenti correlati

Altri documenti