Gold Note PA-10 Manuale utente

USER

MANUAL

PA-10

EN

DE

IT

Thank you for purchasing one of our units

and welcome into the Gold Note world,

where we turn High-End audio and music

into a new experience.

Maurizio Aterini,

founder of Gold Note

EN

DE

IT

|

IMPORTANT SAFETY

| INFORMATIONS

|A grounding type plug has two blades and

a third grounding prong. The wide blade or

the third prong are provided for your safety.

If the provided plug does not fit into

your outlet, consult an electrician for

replacement of the obsolete outlet. or

pinched particularly at plugs, convenience

receptacles, and the point where they exit

from the apparatus.

|Only use attachments/accessories specied

by the manufacturer.

|Use only with the cart, stand, tripod,

bracket, or table specied by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

|Unplug this apparatus during lightning

storms or when unused for long periods

of time. Refer all servicing to qualied

service personnel only. Servicing is required

when the apparatus has been damaged in

any way (such as when the power cord or

plug is damaged, liquid has been spilled

or objects have fallen into the apparatus,

the apparatus has been exposed to rain

or moisture) and in any case when the

apparatus does not operate normally or

has been dropped.

PLEASE NOTE

1 Do not disassemble any part of the

product.

2 Do not use any part of the product for

other purposes.

3 For service and problems of any kind,

contact qualified Gold Note personnel.

4 Protect the product from rain, humidity

and keep away from heat sources, electric

and electronic motors etc. The power

cord supplied must be used only on this

unit.

5 Gold Note does not have responsibility

for any improper use of this unit.

GENERIC INFORMATION

|Read these instructions and store them.

|Heed all warnings.

|Follow the instructions.

|Do not use this apparatus near water.

|Clean only with a dry cloth.

|Do not block the ventilation openings

and install in accordance with the

manufacturer’s instructions.

|Do not install near heat sources such as

radiators, heat registers, stoves or other

apparatus (including ampliers) that

produce heat.

|Do not defeat the safety purpose of

the polarised or grounding-type plug: a

polarised plug hastwo blades with one

wider than the other.

EN

DE

IT

This appliance has a serial number located on the rear panel.

Please record the model and serial number and retain them for your records.

MODEL

SERIAL NUMBER

CAUTION!

To reduce the risk of electric shock, do not

remove cover (or back). No user-serviceable

parts inside. Refer only to qualified Gold

Note service personnel for service.

WARNING!

To prevent fire or shock hazard, do not

expose this appliance to rain or moisture.

GOLD NOTE - Information on the correct management of waste from

household Equipment pursuant to the European Directive 2012/19/EU

The crossed-out wheelie bin symbol shown on the equipment or its packaging indicates

that the product, at the end of its useful life, must be collected separately from other waste

to allow its proper treatment and recycling. The user must therefore deliver, free of charge,

the end-of-life equipment to the centres for the separate collection of waste electrical and

electronic equipment, or return it to the dealer in accordance with the procedures established

by the legislation.

The appropriate separate collection of discarded equipment allows for proper recycling,

treatment and environmentally compatible disposal, helping to avoid the possible dispersion

of hazardous substances and negative effects on the environment and health, favouring

the reuse and/or recycling of the materials of which the equipment is composed of. Illegal

dumping of the product by the user involves the application of administrative sanction

provided for by the legislation in force. We invite you consult the current legislation and the

measures adopted by the public service operating in your country or territory.

| INDEX

| PACKAGE CONTENT

INTRODUCTION AND FEATURES 1

TECHNICAL SPECIFICATIONS 2

FRONT PANEL 3

REAR PANEL 4

PA-10 INSTALLATION 5

PRODUCT REGISTRATION 10

TROUBLESHOOTING 11

RELATED PRODUCTS 12

1x

PA-10

1x

POWER

CABLE

1x

GN LINK

CABLE

1x

USER

MANUAL

EN

DE

IT

| INTRODUCTION AND FEATURES

SMALL AND POWERFUL

The PA-10 is the new Power Amplifier of

the series 10, packing plenty of innovative

solutions, developed for high-power

delivery and compact size, the perfect

match for a modern High-End System that

offers the Gold Note signature power and

sound quality. The PA-10 is a fully balanced

amplifier featuring a BTL design (Bridge-

Tied-Load) which allows the unit to easily

switch from Stereo to Mono, increasing the

power rate from 75Watt per channel @ 8Ω

stereo to a considerable 600Watt @ 4Ω

mono. Use two PA-10 and the performance

of your stereo system will increase

noticeably. Audio-grade components, RCA

and XLR connectors, gold-plated speaker

terminals and high-quality circuitry ensure

outstanding sound.

ADJUSTABLE DAMPING FACTOR

The PA-10 features a unique adjustable

Damping Factor design that allows you to

drive any loudspeakers optimally - including

large and challenging speakers (DF High) or

high sensitivity and mini-monitor speakers

(DF Low).

DESIGN AND MATERIALS

The solid steel chassis is made of massive

panels of aluminium to avoid RFI and EMI

and for maximum shielding, following

the design principle of the Series 10 to

seamlessly integrate the PA-10 into our

coherent philosophy inspired by the Italian

tradition.

GN LINK

Our proprietary GN Link technology enables

the PA-10 to work in Master-Slave mode

with other Gold Note sources, such as the

DS-10, turning On/Off the amplifier together

with the master unit. The Master-Slave mode

is a convenient way to enjoy your music

controlling the entire audio chain from one

source only.

OPTIONAL ACCESSORIES

MX-10 card: this card allows the

simultaneous use of the RCA and XLR inputs.

With this card, you don’t have to select

the RCA/XLR input on the rear panel (BAL

switcher), and you can even play music from

two sources at the same time and use the

PA-10 as an analogue mixer.

1

2

MAIN FEATURES

|Power output:

75W@ 8Ω and 150W @ 4Ω per channel,

600W @ 4Ω per channel in mono (BTL)

|Frequency response:

10Hz-30kHz at +/-1dB

|THD – Total Harmonic Distortion:

0,05%

|Damping factor:

High= 250

Low= 25

|Input sensitivity:

1,4V RMS on RCA and XLR

|Input impedance:

13kΩ RCA/XLR

AUDIO INPUTS

RCA Stereo unbalanced

XLR Stereo balanced

AUDIO OUTPUTS

Speaker terminals:

Gold Plated Binding Posts

HIGH POWER AMP

The PA-10 is capable of:

75W @ 8Ω Stereo load

150W @ 4Ω Stereo load

300W @ 2Ω Stereo load

300W @ 8Ω Mono (BTL) load

600W @ 4Ω Mono (BTL) load

| TECHNICAL SPECIFICATIONS

1x

2x

1x

POWER

|Power supply:

100-240V, 50/60Hz

|Standby power:

<1W

|<10W no signal

|Power Consumption:

600W (nominal power)

|Dinamic power:

1400W max

|Fuse 6,3A T

DIMENSIONS AND WEIGHT

Dimensions:

200W | 80H | 260D mm

290W | 180H | 390D mm - boxed

Weight:

Kg. 4

Kg. 5 - boxed

OPERATING CONDITION LIMITS

Temperature:

From 0°C to 35°C

Humidity:

90% without condensation

EN

DE

IT

FRONT PANEL OVERVIEW

The LED light turns blue when PA-10 is

powered.

| FRONT PANEL

1

3

LED status light

1

Red = standby

Blue = ON

REAR PANEL OVERVIEW

| REAR PANEL

POWER

Right channel

6Press BTL switch to use in

Mono, the Led above turns

blue.

Press DF switch for low

damping factor, the Led

above turns blue.

Press BAL switch to activate

the XLR inputs, the Led

above turns blue.

5

AC IEC plug with integrated

fuse holder drawer 6,3A T

5x20mm at 100/240V.

8

12V IN/OUT (3.5mm) to

synchronise with other Gold

Note units.

4

AUDIO INPUTS

LINE INPUTS

GN LINK

RCA unbalanced

1

Master switch ON/OFF

9

XLR balanced

3

1

6 7

XLR balanced

2

2 3 4

8

9

SPEAKER OUT

Left channel

MONO MODE (BTL)

See page 6 for more info.

ATTENTION

The left - and right + outputs

are electrically interconnected.

7

4

5

EN

DE

IT

RCA CONNECTION

The PA-10 can be connected to your audio

system via unbalanced RCA inputs or

balanced XLR inputs. The PA-10 is extremely

| PA-10 INSTALLATION

5

XLR CONNECTION

Press the BAL button on the rear of the

PA-10 to use the XLR connection.

SPEAKER RIGHT

GN Link

SPEAKER RIGHT

SPEAKER LEFT

DS-10

PA-10

GN LINK

Control multiple units in

Master-Slave mode by

turning ON/OFF just one.

PA-10

When BAL is active, the

LED above turns blue.

flexible and you can set it up in a wide

variety of configurations, as shown in the

following pages.

IN

6

EN

DE

IT

GN Link

SPEAKER RIGHT SPEAKER LEFT

MONO MODE (BTL) XLR

CONNECTION WITH TWO PA-10

Press the BAL and BTL buttons of each PA-10

for this configuration.

PA-10

DS-10

PA-10

When BTL is active

(PA-10 in mono),

the LED above

turns blue.

MONO MODE (BTL) RCA

CONNECTION WITH TWO PA-10

Press the BTL button of each PA-10 for this

configuration.

IN ININOUT

7

GN Link

BI-WIRING CONNECTION

The PA-10 can be easily matched with

speakers designed for bi-wiring.

PA-10

DS-10

PA-10

Both the PA-10

must be set in

MONO (BTL is

active and the LED

is blue).

To drive bi-wiring speakers, you need a pair

of PA-10s which must both be set in MONO

mode. Connect the cables as shown in the

picture below to complete the installation.

IN ININOUT

SPEAKER RIGHT

bi-wiring

SPEAKER LEFT

bi-wiring

8

PA-10

DS-10

PA-10

XLR CONNECTION WITH TWO PA-10

AND FOUR LOUDSPEAKERS

Press the BAL button of each PA-10 for this

configuration.

GN Link

SPEAKER RIGHT 1 SPEAKER RIGHT 2

SPEAKER LEFT 1 SPEAKER LEFT 2

EN

DE

IT

IN INOUT

9

PA-10

DS-10

PA-10

XLR CONNECTION WITH FOUR

PA-10 AND FOUR LOUDSPEAKERS

Press the BAL and BTL buttons of each PA-10

for this configuration.

GN Link

SPEAKER RIGHT 1 SPEAKER RIGHT 2

SPEAKER LEFT 2SPEAKER LEFT 1

IN

OUT

| PRODUCT REGISTRATION

10

EN

DE

IT

PRODUCT REGISTRATION

We recommend to register the unit on our

internet website within 15 days from the

purchase at

www.goldnote.it/product-registration

Registering your product ensures that you

will always receive communications about

updates, information, and news regarding

your product.

WARRANTY

All Gold Note products come with a

warranty against defective materials and

workmanship.

Any service and inspection must be carried

out by a Gold Note dealer or distributor so

in case you need any assistance with this

product, please contact the seller.

PLEASE NOTE

Descriptions and technical characteristics

may vary at any time and without notice.

ATTENTION

Gold Note products should only be

opened, serviced and inspected by certified

Gold Note technicians and dealers. Work

performed by unqualified personnel may

cause serious damage or personal injury.

Opening of the product by non-authorised

personnel will void the guarantee.

In this case, contact your dealer to be

advised on how the fault can be solved.

Do not return any object directly to the

factory or to the distributor without being

authorised to do so.

www.goldnote.it/product-

registration

| TROUBLESHOOTING

PROBLEM

CLEANING THE UNIT

CAUSE SOLUTION

The speakers hum when

the amplier is connected

to the system.

With EXTREME care use ONLY water or detergents for delicate surfaces with a very soft

cloth to sweep dust and remove stains.

Any acid or not extremely soft cloth will irreversibly damage the unit ne aesthetic. Do not

use alcohol.

The unit does not work

when the stage is switched

ON.

|The unit is not correctly

coupled with the Ground

on DC.

|The AC Stage plug is

disconnected from the

wall power outlet.

|Ensure the system is well

grounded and check the

ground Pin on the power

cord plug.

|Make sure it’s connected

and that the wall outlet

works.

|The interconnect input

and/or output cables are

not shielded.

|The interconnect

cables are not properly

connected to the amp.

|One of the fuses is blown.

The unit buzzes every time

it is turned ON or OFF.

|Be sure to always use

shielded cables for the

amp connections.

|Make sure they are

properly connected and

working.

|Substitute the fuse with

one of the same value

(6,3A T 5x20).

|Turn Off the amplier as

rst but turn it on as last

of the audio system unit.

11

| RELATED PRODUCTS

CARTRIDGES

|DONATELLO

Lightweight MC phono cartridge with

top-of-the-range performance. Features

Micro Elliptical diamonds, copper coils and

Duraluminium body.

|VASARI

High-quality MM phono cartridge featuring

Elliptical or Conical diamond tips and

copper coils in a special computer-

designed body.

TURNTABLES

|PIANOSA

Italian design meets technical innovation

and impeccable finishes. Pianosa is a

handmade turntable featuring a 23mm

platter made of damping polyvinyl and

our proprietary motor powered by micro-

controlled for 33/45rpm.

|VALORE 425 PLUS

Available in 4 luxurious finishes, Valore

425 Plus is a handmade turntable and

features a 23mm platter made of PTE. A

classic design delivering excellent audio

performances.

ELECTRONICS

|DS-10

Our modern Streaming DAC with Preamp

and Headphone Output, the DS-10 and

DS-10 PLUS are the core of a modern and

compact audio system.

|PH-10

The PH-10 is a fully analogue phono

preamplifier that offers unique features,

including EQ CURVES, LOAD and GAIN

adjustments, and an intuitive UX thanks to

its SKC (Single Knob Control) and display.

LOUDSPEAKERS

|A3 EVO II

Elegant and compact, the A3 EVO is

a 2-way loudspeaker with bass reflex.

Modern Italian looks, stunning materials

and audiophile sound.

Discover more on our website

www.goldnote.it

EN

DE

IT

12

13

La pagina sta caricando ...

Gold Note PA-10 Manuale utente

Gold Note PA-10 Manuale utente

in altre lingue

Documenti correlati

Altri documenti