Pella 80KM0103 Manuale utente

Marca: Pella

Modello: 80KM0103

Tipo: Manuale utente

INSTALLATION INSTRUCTIONS

HINGED PATIO DOOR - SOUTHWESTERN WALL WITH HARD COAT STUCCO

Installation Instructions for Typical Wood Frame Construction.

These instructions were developed and tested for use with typical wood frame wall construction in a wall system designed to manage water.

These instructions are not to be used with any other construction method. Installation instructions for use with other construction methods,

multiple units or bow and bay windows, may be obtained from Pella

Corporation or a local Pella retailer. Building designs, construction methods,

building materials, and site conditions unique to your project may require an installation method different from these instructions and additional

care. Determining the appropriate installation method is the responsibility of you, your architect, or construction professional.

YOU WILL NEED TO SUPPLY:

s#EDAROR)MPERVIOUSSHIMSSPACERSTO

sGALVANIZEDROOlNGNAILSLB

s#LOSEDCELLFOAMBACKERRODSEALANTBACKERTOFT

s0ELLA

3MART&LASHFOILBACKEDBUTYLWINDOWANDDOOR

ﬂashing tape or equivalent

s(IGHQUALITYEXTERIORGRADEPOLYURETHANEORSILICONESEALANT

TOTUBESPERDOOR

s'REAT3TUFF

™

Window and Door Insulating Foam Sealant

by the Dow Chemical Company or equivalent low pressure

polyurethane window and door foam - DO NOT use high

PRESSUREORLATEXFOAMS

s0ELLAALUMINUMSILLSUPPORTORXWOODBLOCKING

s)NTERIORTRIMANDORJAMBEXTENSIONSTOFT

sWIDE&ORTIlBERmASHINGPAPEROREQUIVALENT

TOOLS REQUIRED:

s4APEMEASURE

sg,EVEL

s3QUARE

s(AMMER

s3TAPLER

s3EALANTGUN

s3CISSORSORUTILITYKNIFE

s$RILL

s3CREWDRIVERS

 0HILLIPSWITHSHAFTANDSMALLmATBLADE

4&"-"/5



'MBTIJOH1BQFS

4JMM'MBTIJOH5BQF

4JMM'MBTIJOH5BQF

4JMM4VQQPSU

5PQ

'MBTIJOH

5BQF

'JO

$PSOFS

4JEF

'MBTIJOH

5BQF

*OUFSMPDLFS

4JEF

'MBTIJOH

5BQF

/BJMJOH'JO

XJEF'MBTIJOH1BQFS

Always read the Pella

,IMITED7ARRANTYBEFOREPURCHASINGORINSTALLING0ELLAPRODUCTS"YINSTALLINGTHISPRODUCTYOUAREACKNOWLEDGING

that this Limited Warranty is part of the terms of the sale. Failure to comply with all Pella installation and maintenance instructions may void your Pella product

warranty. See Limited Warranty for complete details at http://warranty.pella.com.

REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.

Part Number: 80KM0103

1 ROUGH OPENING PREPARATION

A. Verify the opening is plumb and level.

Note: It is critical that the bottom is level.

B. Verify the door will ﬁt the opening.-EASUREALLFOURSIDESOFTHEOPENINGTOMAKE

SUREITISLARGERTHANTHEDOORINWIDTHANDLARGERINHEIGHT-EASURETHE

width at the top, bottom, and center. Measure the height at the far left side, the far

right side, and in the center.

Note: 1-1/2" or more of solid wood blocking is required around the perimeter of

the opening. Fix any problems with the rough opening before proceeding.

C. Apply ﬂashing paper at the bottom##UTONEPIECEOFmASHINGPAPERLONGER

than the width of the rough opening. Position the top edge of the ﬂashing paper with

the top of the sill plate. Center the ﬂashing paper with the opening width. Staple the

ﬂashing paper to the sill plate.

Note: Sill ﬂashing paper is not required for installation on concrete ﬂoors.

D. Apply ﬂashing paper to the sides of the rough opening$#UTTWOPIECESOF

mASHINGPAPERLONGERTHANTHEHEIGHTOFTHEROUGHOPENING!PPLYONEPIECETO

each jamb. Position the edge of the ﬂashing paper with the inside edge of the trimmer

JACKSTUDANDCENTERTHEmASHINGPAPERWITHTHEHEIGHTOFTHEROUGHOPENING3TAPLE

the ﬂashing paper to the trimmer.

E. Apply bottom ﬂashing tape #1.#UTAPIECEOFmASHINGTAPELONGERTHANTHEOPENING

WIDTH!PPLYATTHEBOTTOMOFTHEOPENINGASSHOWN%SOITOVERHANGSTOTHEEXTERIOR

Note: The tape is cut 12" longer than the width of the opening so that it will extend up

each side approximately 6".

F. Tab the bottom ﬂashing tape and fold.#UTWIDETABSATEACHCORNERFROMEACHSIDE

OFCORNER&&OLDTAPETOTHEEXTERIORANDPRESSlRMLYTOADHEREITTOTHEmASHINGPAPER

'Apply bottom ﬂashing tape #2.#UTAPIECEOFmASHINGTAPELONGERTHANTHEOPENING

WIDTH!PPLYATTHEBOTTOMOVERLAPPINGTAPEBYATLEAST$/./4ALLOWTHETAPETO

EXTENDPASTTHEINTERIORFACEOFTHEFRAMING'

In-swing Architect Series

and Designer Series

:)FTHEWALLDEPTHISGREATERTHANADDA

THIRDPIECEOFmASHINGTAPE4HEmASHINGTAPESHOULDCOMETOWITHINOFTHEINTERIORFACEOF

the framing.

Note: The ﬂashing tape does not need to extend all the way to the interior of the framing.

(Attach the aluminum sill support or wood blockingTOTHEEXTERIOROFTHEBOXPLATE

to support the edge of the door sill. Place the sill support ﬂush with the subﬂoor.

£

£

£

£







£

£



£

£

2 SETTING AND FASTENING THE DOOR

A. Remove plastic wrap and cardboard packaging from door. DO NOT remove plastic

SHIPPINGSPACERS4HESHIPPINGSPACERSWILLHELPKEEPTHEDOORSQUAREDURINGINSTALLATION

$/./4UNLOCKOROPENTHEDOORUNTILITISFULLYFASTENED

Note: If screens, grilles or hardware are removed from the door at this time, label

them and store them in a protected area.

B. Fold out installation ﬁn to 90°."ECAREFULNOTTOREMOVEORTEARTHElNCORNERS

Note: If the ﬁn is not at 90°, the door will not line up correctly on the interior.

C. Place three 3/8" beads of sealant.4HElRSTBEADSHOULDBEAPPROXIMATELYFROM

THEEXTERIOROFTHEROUGHOPENINGTHESECONDBEADSHOULDBEPLACEDSOITISUNDERTHE

WOODINTERIORTHRESHOLDOFTHEDOOR0LACEMENTWILLVARYDEPENDINGONWALLTHICKNESS

ANDDOORTYPE0LACEATHIRDBEADOFSEALANTINTHEGROOVEOFTHESILLSUPPORTOR

FROMTHEEXTERIOREDGEOFTHEWOODBLOCKING

TWO OR MORE PEOPLE WILL BE REQUIRED FOR THE FOLLOWING STEPS.

D. Insert the doorFROMTHEEXTERIOROFTHEBUILDING$/./4SLIDETHEBOTTOMOF

the door into the opening. Sliding will damage the sealant lines. Place the bottom

of the door at the bottom of the opening, then tilt the top into position. Center the

door between the sides of the opening to allow clearance for shimming, and insert

ONEROOlNGNAILINTHElRSTHOLEFROMTHECORNERONEACHENDOFTHETOPNAILINGlN

These are used to hold the door in place while shimming it plumb and square.

E. Plumb and square door.0LACESHIMSATEACHHINGEANDLOCKSTRIKELOCATIONBETWEENTHE

DOORANDTHESIDESOFTHEOPENING)NSERTSHIMSINOTHERLOCATIONSASNEEDEDSTARTINGUP

FROMTHEBOTTOMOFTHEDOORTOSQUAREITINTHEOPENING-AKESURETHATTHEREVEALAROUND

THEDOORSISEQUAL/NDOUBLEDOORSMAKESURETHATPANELSAREEVENACROSSTHEBOTTOM

Note: On center latch double doors the lock strike will not be shimmed since it is

located in the center of the unit. DO NOT over shim.

F. Check the interior reveal.-AKESURETHEMEASUREMENTFROMTHEINTERIORFACEOFTHEDOOR

to the interior face of the wall is equal at several points around the door.

Note: If the dimensions are not equal, check to make sure the ﬁns are folded out to 90°

at all points.

Ó

Ó

&YUFSJPS

Ó

&YUFSJPS

Ó

*OUFSJPS

Ó

Óä

Îä {ä xä Èä Çä

ÓÎ

 -



Ó

'Fasten the door to openingBYDRIVINGGALVANIZEDROOlNGNAILSINTOEACH

PREPUNCHEDHOLEINTHENAILINGlN

Note: Make sure the ﬁn corner is lying as ﬂat as possible. When using

the optional ﬁn at the sill, attach the aluminum sill support or wood

blocking under the sill of the door before proceeding to Step H.

( Carefully open the door(s) and remove all shipping spacers.

Note: Be sure to remove the spacers from the bottom edge of the door panel.

Double doors with center latch:

Designer Series Only: Use the construction handle to operate the active door

HANDLE/PERATETHEmUSHBOLTSPERTHEINSTRUCTIONSONTHELABELONTHESTRIKE

located on the astragal.

Architect Series Only: Use the construction handle to operate both the active

and passive door panels.

I. Out-swing doors: Place a dab of sealant in each of the pre-drilled holes in the bottom of the door frame, then insert a

XmATHEADCORROSIONRESISTANTWOODSCREWPROVIDEDINTOTHISHOLE

Note: Single doors will have two pre-drilled holes, double doors will have four.

)Out-swing double doors only:0LACEADABOFSEALANTINTOTHECENTERHOLEOFTHESTRIKEPLATELOCATEDATTHESILLOFTHEDOOR

)NSTALLAXmATHEADCORROSIONRESISTANTWOODSCREWPROVIDEDINTOTHISHOLE

Note: For masonry ﬂoors, use a #8 masonry screw instead of the wood screw.

J. On center latching (double) doors: Place shims at the top of the door frame above

THECENTERSTRIKEPLATE3ECURETHESHIMSBYINSERTINGAXmATHEADCORROSION

RESISTANTSCREWINTOTHEUPPERDOORFRAMETHROUGHTHECENTERHOLEOFTHESTRIKEPLATE

and the shims into the rough opening.

*On center hinged double doors: Insert and attach shims directly

above the astragal in the center of the unit.

Note: Step K does not apply to center hinged doors.

K. On each hinge, starting at the top, insert a 3" long screwPROVIDEDINTOTHE

OPENSCREWHOLE-AKESURETHATTHESCREWPASSESTHROUGHTHESHIMSANDINTOTHE

structural framing.

L. Check door operation./PENANDCLOSETHEDOORTOCHECKFORPROPEROPERATION

-AKESURETHEDOORWILLLATCHCORRECTLY

Note: If there are any problems with the operation, recheck and adjust the reveal.

M. Adjust the reveal if needed.

Architect Series and Designer Series only:4HEDOORPANELSHAVEADJUSTABLEHINGELEAFS5SINGAALLENWRENCH

TURNTHECENTERSCREWCLOCKWISETOINCREASETHESPACEBETWEENTHEHINGESIDEOFTHEFRAMEANDTHEDOORPANELORCOUNTER

CLOCKWISETOINCREASETHESPACEBETWEENTHEDOORPANELANDTHELOCKSIDEOFTHEFRAME$/./4TURNTHESCREWSMORE

THANTURNINEITHERDIRECTION)NSOMECASESITMAYBENECESSARYTOLOOSENANDTHENTIGHTENTHETOPANDBOTTOMHINGE

screws to obtain full hinge adjustment. If necessary, loosen the top and bottom screws, and immediately retighten them.

With the screws retightened, turn the adjustment hinge screw. If the hinge will not adjust any further then it is adjusted

as far as it will go. If more clearance is needed adjust the shims between the frame and the rough opening.

Note: DO NOT adjust the hinge with the top and bottom screws loose; this could force the hinge to adjust beyond

its design capability which can cause the hinge to bind, damage the hinge and/or pull out the screws. A 3/4 turn of

the center screw provides approximately 1/16" adjustment.

Note: For more issues with the adjustable strike latching, go to the troubleshooting section at the end of this instruction.

ProLine Series only: Plastic shims located behind the hinges may be removed to adjust the reveal between the door panel

and door frame. Additional hinge shims may be added if required.

N. On doors with a lock strike in the side,DRILLADIAMETERXDEEPPILOTHOLETHROUGHTHELOCKSTRIKEANDINTOTHE

ROUGHOPENING)NSERTAXCORROSIONRESISTANTSCREWPROVIDEDINTOTHEPILOTHOLEMAKINGSURETHATITPASSESTHROUGH

the shim and into the stud.

Note: This step does not apply to center latching double doors.

O. Install a #8 x 3" ﬂat head corrosion resistant screwINTOTHEHOLELOCATEDAPPROXIMATELYFROMTHETOPOFTHE

door frame, on the latch side of the frame.

&YUFSJPS

Ó

Ó

*OUFSJPS

Ó

Ó

Ó

3 INTEGRATING THE DOOR TO THE BUILDING FELT

Note: The ﬂashing tape must be applied approximately 1/2" onto the frame cladding at the jambs and

head. Pre-folding the tape at 1/2" before removing the paper backing will make it easier to apply the

tape correctly. If the siding is less than 1/2" thick, adjust the dimension of the fold so the exterior sealant

line will cover the exterior edge of the tape.

A. Apply side ﬂashing tape.#UTPIECESOFmASHING

TAPELONGERTHANTHEFRAMEHEIGHTOFTHEDOOR

!PPLYONEPIECEUPONTOTHEFRAMECLADDING

OVERTHENAILINGlNANDONTOTHEmASHINGPAPERTO

EACHSIDE4HETAPESHOULDEXTENDABOVETHETOP

OFTHEDOORANDBELOWTHEBOTTOMOFTHEDOOR

0RESSTHETAPEDOWNlRMLYWHILEFOLDINGDOWNTHE

EXCESSTAPEATTHETOPANDBOTTOMOFTHEDOOR

B. Apply top ﬂashing tape. Cut a piece of ﬂashing tape long enough to go across

THETOPOFTHEDOORANDEXTENDATLEASTPASTTHESIDEmASHINGTAPEONBOTHSIDES

!PPLYTHETAPEUPONTOTHEFRAMECLADDINGOVERTHETOPNAILINGlNASSHOWN

&OLDTHEOVERLAPPINGTAPEDOWNANDPRESSALLTAPEDOWNlRMLY

Note: The top ﬂashing tape must overlap the side ﬂashing tape to prevent

water from getting behind it.

C. Apply the top ﬂashing paper.#UTONEPIECEOFmASHINGPAPERATLEASTLONGERTHANTHE

width of the rough opening. Position the bottom edge of the ﬂashing paper ﬂush with the

frame of the door and center the ﬂashing paper with the door. Staple the ﬂashing paper to

the header.

Note: When applying the ﬁrst layer of building felt, ensure the sill ﬂashing paper

overlaps the building felt. This will tie the door system into the building water

management system.

&YUFSJPS

Î

&YUFSJPS

Î



Î

4 INTERIOR SEAL

Caution: Ensure use of low pressure polyurethane window and door installation foams and strictly follow the foam manufacturer’s

recommendations for application. Use of high pressure foams or improper application of the foam may cause the door to bow and

hinder operation. DO NOT use ﬁberglass insulation.

A. Apply insulating foam. &ROMTHEINTERIORINSERTTHENOZZLEOFTHEAPPLICATORAPPROXIMATELY

DEEPINTOTHESPACEBETWEENTHEDOORANDTHEROUGHOPENINGANDAPPLYADEEPBEAD

OFFOAM4HISWILLALLOWROOMFOREXPANSIONOFTHEFOAMANDWILLMINIMIZESQUEEZEOUT)F

USINGFOAMOTHERTHAN'REAT3TUFF7INDOWAND$OOR)NSULATING&OAM3EALANTBYTHE

$OW#HEMICAL#OMPANYALLOWTHEFOAMTOCURECOMPLETELYUSUALLYTOHOURSBEFORE

PROCEEDINGTOTHENEXTSTEP

Note: DO NOT completely ﬁll the space from the back of the ﬁn to the interior face of

the opening.

*OUFSJPS

{

B. Check the door operation by opening and closing the door.

Note: If the door does not operate correctly, check to make sure it is still plumb, level, square and

that the sides are not bowed. If adjustments are required, remove the foam with a serrated knife.

Adjust the shims, and reapply the insulating foam sealant.

5 SEALING THE DOOR TO THE EXTERIOR WALL CLADDING

Note: When applying the casing bead for stucco, leave 1/2" space between the

head of the door and the casing bead, and 3/8" space between the door jambs

and the casing bead for backer rod and sealant. Refer to the illustration

(Southwestern Wall With Stucco).

Note: The sealant details shown are standard recommendations from the

sealant industry. Contact your sealant supplier for recommendations and

instructions for this and any other application.

A. Install the hardware.2EFERTOTHEINSTRUCTIONSINCLUDEDINTHEHARDWAREBOX

B. Insert backer rodINTOTHESPACEAROUNDTHEDOORLEAVINGATLEASTA

CLEARANCEBETWEENTHEBACKERRODANDTHEEXTERIORFACEOFTHECASINGBEAD

Note: Backer rod adds shape and depth for the sealant line.

C. Apply a bead of high quality exterior grade sealant

to the entire perimeter of the door. At each end of the

bottom of the door, insert sealant into the spaces between

the bottom of the door and the sill support and connect

it to the perimeter sealant.

D. Shape, tool and clean excess sealant. 7HENlNISHED

the sealant should be the shape of an hourglass.

Note: This method creates a more ﬂexible sealant

line capable of expanding and contracting.

E. Remove plastic guards at the base of the door

once construction is complete.

4065)8&45&3/

8"--

8*5)

456$$0

$MFBSBODF

#BDLFS3PEBOE

4FBMBOUUZQJDBM

*OTVMBUJOH

'PBN

"DDFTTPSZ

(SPPWF



x

x

6 INTERIOR FINISHING

)FTHEPRODUCTSCANNOTBElNISHEDIMMEDIATELYCOVERWITHCLEARPLASTICTOPROTECTFROMDIRTDAMAGEANDMOISTURE2EMOVEANYCONSTRUCTION

RESIDUEBEFORElNISHING3ANDALLWOODSURFACESLIGHTLYWITHGRITORlNERSANDPAPER$/./4USESTEELWOOL"%#!2%&5,./44/

3#2!4#(4(%',!332EMOVESANDINGDUST

0ELLAPRODUCTSMUSTBElNISHEDPERTHEBELOWINSTRUCTIONSFAILURETOFOLLOWTHESEINSTRUCTIONSVOIDSTHE,IMITED7ARRANTY

s/NCASEMENTANDAWNINGSITISOPTIONALTOPAINTSTAINORlNISHTHEVERTICALANDHORIZONTALSASHEDGES

s/NSINGLEHUNGANDDOUBLEHUNGDONOTPAINTSTAINORlNISHTHEVERTICALSASHEDGESANYlNISHONTHEVERTICALSASHEDGESMAYCAUSETHESASH

TOSTICKITISOPTIONALTOPAINTSTAINORlNISHTHEHORIZONTALSASHEDGES

s/NPATIODOORSITISOPTIONALTOPAINTSTAINORlNISHTHEVERTICALANDHORIZONTALPANELEDGES

Note: To maintain proper product performance do not paint, ﬁnish or remove the weather-stripping, mohair dust pads, gaskets or vinyl

parts. Air and water leakage will result if these parts are removed. After ﬁnishing, allow venting windows and doors to dry completely

before closing them.

0ELLA#ORPORATIONISNOTRESPONSIBLEFORINTERIORPAINTANDSTAINlNISHIMPERFECTIONSFORANYPRODUCTTHATISNOTFACTORYAPPLIEDBY0ELLA

#ORPORATION5SEOFINAPPROPRIATElNISHESSOLVENTSBRICKWASHORCLEANINGCHEMICALSWILLCAUSEADVERSEREACTIONSWITHWINDOWANDDOOR

materials and voids the Limited Warranty.

&ORADDITIONALINFORMATIONONlNISHINGSEETHE0ELLA/WNERS-ANUALORGOTO www.pella.com.

EXTERIOR FINISH

4HEEXTERIORFRAMEANDSASHAREPROTECTEDBYALUMINUMCLADDINGWITHOURTOUGH%NDURA#LAD

OR%NDURA#LAD0LUSBAKEDONFACTORY

lNISHTHATNEEDSNOPAINTING#LEANTHISSURFACEWITHMILDSOAPANDWATER3TUBBORNSTAINSANDDEPOSITSMAYBEREMOVEDWITHMINERAL

spirits. DO NOT use abrasives. DO NOT scrape or use tools that might damage the surface.

5SEOFINAPPROPRIATElNISHESSOLVENTSBRICKWASHORCLEANINGCHEMICALSWILLCAUSEADVERSEREACTIONSWITHWINDOWANDDOORMATERIALSAND

voids the Limited Warranty.

CARE AND MAINTENANCE

#AREANDMAINTENANCEINFORMATIONISAVAILABLEINTHE0ELLA/WNERS-ANUAL9OUCANOBTAINANOWNERSMANUALBYCONTACTINGYOURLOCAL

Pella retailer. This information is also available at www.pella.com.

IMPORTANT NOTICE

"ECAUSEALLCONSTRUCTIONMUSTANTICIPATESOMEWATERINlLTRATIONITISIMPORTANTTHATTHEWALLSYSTEMBEDESIGNEDANDCONSTRUCTEDTO

properly manage moisture. Pella Corporation is not responsible for claims or damages caused by anticipated and unanticipated water

INlLTRATIONDElCIENCIESINBUILDINGDESIGNCONSTRUCTIONANDMAINTENANCEFAILURETOINSTALL0ELLAPRODUCTSINACCORDANCEWITH0ELLAS

INSTALLATIONINSTRUCTIONSORTHEUSEOF0ELLAPRODUCTSINWALLSYSTEMSWHICHDONOTALLOWFORPROPERMANAGEMENTOFMOISTUREWITHINTHE

wall systems. The determination of the suitability of all building components, including the use of Pella products, as well as the design

and installation of ﬂashing and sealing systems are the responsibility of the Buyer or User, the architect, contractor, installer, or other

construction professional and are not the responsibility of Pella.

Pella products should not be used in barrier wall systems which do not allow for proper management of moisture within the wall systems,

SUCHASBARRIER%XTERIOR)NSULATIONAND&INISH3YSTEMS%)&3ALSOKNOWNASSYNTHETICSTUCCOOROTHERNONWATERMANAGEDSYSTEMS

%XCEPTINTHESTATESOF#ALIFORNIA.EW-EXICO!RIZONA.EVADA5TAHAND#OLORADOPella makes no warranty of any kind on and

assumes no responsibility for Pella windows and doors installed in barrier wall systems. In the states listed above, the installation

of Pella products in barrier wall or similar systems must be in accordance with Pella’s installation instructions.

0RODUCTMODIlCATIONSTHATARENOTAPPROVEDBY0ELLA#ORPORATIONWILLVOIDTHE,IMITED7ARRANTY

TROUBLESHOOTING - Adjustable Strike Latching Issues

5"#4

"EKVTUBCMFTUSJLFTIJN

TJEFWJFX

4USJLF

GSPOUWJFX

"EK4USJLF4IJN

FOEWJFX

'BDUPSZ

JOTUBMMFE

TJEF

4JEFUPCF

VTFEJO

*TTVF

Issue 2:

Door needs to close more

tightly against the weather-

strip. Remove

THESTRIKEAND

ADJUSTABLESTRIKE

shim. Remove

the tabs from the

ADJUSTABLESTRIKE

shim and install

SOTHATTHETHICKER

side is visible at

THESTRIKEEDGE

2EINSTALLTHESTRIKE

Issue 1:

Door is difﬁcult

to latch. Remove

THESTRIKEAND

ADJUSTABLESTRIKE

shim then reinstall

THESTRIKE

Note: Troubleshooting is for Architect Series

and Designer Series

only.

Pella 80KM0103 Manuale utente

Marca: Pella

Modello: 80KM0103

Tipo: Manuale utente

Scarica PDF

rapporto

in altre lingue

English: Pella 80KM0103 User manual

Pella 80KM0103 Manuale utente

Pella 80KM0103 Manuale utente

in altre lingue

Documenti correlati

Altri documenti