Biostar A740G3L - BIOS Setup Manual

A780L3L Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. There is no guarantee

that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the

contents here and specially disclaims any implied warranties of merchantability

or fitness for any purpose. Further the vendor reserves the right to revise this

publication and to make changes to the contents here without obligation to

notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and

we will not be responsible for any mistakes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ........................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 3

1.5 Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation .......................... 5

2.1 Installing Central Processing Unit (CPU)....................................... 5

2.2 FAN Headers...................................................................................... 7

2.3 Installing System Memory................................................................ 8

2.4 Connectors and Slots ....................................................................... 10

Chapter 3: Headers & Jumpers Setup ................... 13

3.1 How to Setup Jumpers .................................................................... 13

3.2 Detail Settings.................................................................................. 13

Chapter 4: RAID Functions .................................. 18

4.1 Operating System............................................................................ 18

4.2 Raid Arrays ...................................................................................... 18

4.3 How RAID Works............................................................................. 18

Chapter 5: Useful Help ........................................ 21

5.1 Driver Installation Note.................................................................. 21

5.2 Software............................................................................................ 22

5.3 Extra Information............................................................................ 26

5.4 Troubleshooting............................................................................... 28

Appendix: SPEC In Other Languages ................... 30

German.................................................................................................................. 30

French .................................................................................................................... 32

Italian..................................................................................................................... 34

Spanish ................................................................................................................... 36

Portuguese ............................................................................................................ 38

Polish...................................................................................................................... 40

Russian ................................................................................................................... 42

Arabic..................................................................................................................... 44

Japanese ................................................................................................................ 46

A780L3L

1

CHAPTER 1: INTRODUCTION

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the

motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely

grounded appliance, or use grounded wrist strap to

remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board

on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short

circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

1.2 PACKAGE CHECKLIST

HDD Cable X 1 (optional)

Serial ATA Cable X 2

Rear I/O Panel for ATX Case X 1

Installation Guide X 1

Fully Setup Driver CD X 1 (full version manual files inside)

FDD Cable X 1 (optional)

USB 2.0 Cable X1 (optional)

S/PDIF out Cable X 1 (optional)

Serial ATA Power Cable X 1 (optional)

Note: The package contents may be different due to area or your motherboard version.

Motherboard Manual

2

1.3 MOTHERBOARD FEATURES

SPEC

CPU

Socket AM3

AMD Sempron / Athlon II / Phenom II

processors

(Maximum Watt: 95W)

AMD 64 Architecture enables 32 and 64 bit

comput ing

Supports Hyper Transport 3.0

FSB

Support HyperTransport 3.0

Supports up to 3.2 GT/s Bandwidth

Chipset

AMD RS780L

AMD SB710

Super I/O

ITE 8721

Provides the most commonly used leg acy

Super I/O functionality

Low Pin Count Interface

Environment Control in it iatives

H/W Monitor

ITE's "Smart Guardian" function

Main

Memory

DDR3 DIMM Slots x 2

Max Memory Capacity 8GB

Each DIMM supports 512MB/

1GB/2GB/4GB DDR3

Dual Channel Mode DDR3 memory module

Supports DDR3 800 / 1066 / 1333

Registered DIMM and ECC DIMM is not supported

Graphics Integrated in AMD RS780L Chipset

Max Shared V ideo Memory is 512 MB

DVI/HDCP support

IDE Integr ated IDE Contro ller

Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode

supports PIO Mode 0~4,

SATA II Integrated Serial ATA Controller

Data transfer rates up to 3 Gb/s

SATA Version 2.0 specificat ion co mpliant

LAN Realtek RTL 8103EL

10 / 100 Mb/s auto negotiation

Half / Full duplex capability

Sound ALC662

5.1 channels audio out

High Definition Audio

PCI Express Gen2 x16 slot x1 Supports PCI-E Gen2 x16 expansion cards

Slots

PCI slot x2 Supports PCI expansion cards

Floppy Connector x1 Each connector supports 2 Floppy drives

IDE Connector x1 Each connector supports 2 IDE devices

SATA Connector x4 Each connector supports 1 SATA device

Front Panel Connector x1 Supports front panel facilities

On Board

Connectors

Front Audio Connector x1 Supports front panel audio function

A780L3L

3

SPEC

S/PDIF out Connector x1 Supports digital audio out function

CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)

System Fan Header x1 System Fan Power supply

CMOS clear Header x1 Restore CMOS data to factory default

USB Connector x2 Each connector supports 2 front panel USB ports

Power Connector (24pin) x1 Connects to Power supply

Power Connector (4pin) x1 Connects to Power supply

Printer Port Connector x1 Each connector supports 1 Printer port

Serial Port Connector x1 Connects to RS-232 Port

Back Panel

I/O

PS/2 Keyboard x1

PS/2 Mouse x1

DVI port x1

VGA port x1

LAN port x1

USB Port x4

Audio Jack x3

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connect to DVI-D monitor

Connect to D-SUB monitor

Connect to RJ-45 Ethernet cable

Connect to USB devices

Provide Audio-In/Out and microphone connection

Board Size 182 mm(W) x 235 mm(L)

Special

Features

RAID 0 / 1 / 1+0 support

OS Support Windows XP / Vista / 7

Biostar reserves the right to add or remove support

for any OS With or without notice.

1.4 R

EAR PANEL CONNECTORS

PS/2

Mou se

PS/2

Keyboard

USBX2USBX2

LAN

VGA

Line In/

Surround

Line Out

Mic In 1/

Bass/ Center

DVI-D

Motherboard Manual

4

1.5 MOTHERBOARD LAYOUT

KBMS1

USB1

RJ45USB1

VGA1

DVI1

AUDIO1

JUSBV1

F_AUDIO1

LAN

Super

I/O

Codec

PEX16_1

PCI1

PCI2

FDD1

JUSBV2

J_PRINT1J_COM1

PANEL1

F_USB2

F_USB1

SATA1 SATA2

SYS_FAN1

SATA3

SATA4

BIOS

IDE1

ATXPWR 1

D3_A1DR

DB1DR3_

CPU_FAN1

BATTERY

ATXPWR 2

AMD

RS780L

AMD

SB710

JCMOS1

JSPDIFOUT1

Socket AM3

Note: represents the 1■

st

pin.

A780L3L

5

CHAPTER 2: HARDWARE INSTALLATION

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Pull the lever toward direction A from the socket and then raise the

lever up to a 90-degree angle.

Step 2: Look for the white triangle on socket, and the gold triangle on

CPU should point towards this white triangle. The CPU will fit only

in the correct orientation.

Motherboard Manual

6

Step 3: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the CPU_FAN1. This completes the

installation.

A780L3L

7

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan

cable and connector may be different due to the fan manufacturer.

Connect the fan cable to the connector while matching the black wire to

pin#1.

CPU_FAN1: CPU Fan Header

Assignment

1 Ground

2 +12V

3

FAN RPM rate

sense

1

4

4 Smart Fan

Control (By Fan)

SYS_FAN1: System Fan Header

Assignment

1 Ground

2 +12V

1

3

3 FAN RPM rate

sense

Note:

The CPU_FAN1 supports 4-pin head connector. The SYS_FAN1 supports 3-pin head

connector. When connecting with wires onto connectors, please note that the red wire is

the positive and should be connected to pin#2, and the black wire is Ground and should

be connected to GND.

Motherboard Manual

8

2.3 INSTALLING SYSTEM MEMORY

A. Memory Modules

DB1DR3_

D3_A1DR

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a

DIMM on the slot such that the notch on the DIMM matches the

break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining

chip snap back in place and the DIMM is properly seated.

A780L3L

9

B. Memory Capacity

DIMM Socket

Location

DDR3 Module

Total Mem ory

Size

DDR3_A1 512MB/1GB/2GB/4GB

DDR3_B1 512MB/1GB/2GB/4GB

Max is 8GB.

C. Dual Channel Memory installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table

Dual Channel Status

DDR3_A1

DDR3_B1

Disabled X O

Disabled O X

Enabled O O

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or

x16)

Motherboard Manual

10

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,

720K, 1.2M, 1.44M and 2.88M floppy disk types.

133

234

IDE1: Hard Disk Connector

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO

Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.

21

3940

SATA1~SATA4: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 4channels SATA interface, it

satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s.

Pin Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

74

1

SATA1 SATA2

SATA4

SATA3

7 Ground

A780L3L

11

ATXPWR1: ATX Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX

power supply.

1

12

13

24

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V

14 -12V 2 +3.3V

15 Ground 3 Ground

16 PS_ON 4 +5V

17 Ground 5 Ground

18 Ground 6 +5V

19 Ground 7 Ground

20 NC 8 PW_OK

21 +5V 9 Standby Voltage+5V

22 +5V 10 +12V

23 +5V 11 +12V

24 Ground 12 +3.3V

ATXPWR2: ATX Power Source Connector

Connecting this connector provides +12V to CPU power circuit.

Assignment

1 +12V

2 +12V

3 Ground

34

12

4 Ground

Note:

Before you power on the system, please make sure that both ATXPWR1 and ATXPWR2

connectors have been plugged-in.

Motherboard Manual

12

PEX16_1: PCI-Express Gen2 x16 Slot

- PCI-Express 2.0 compliant.

- Maximum theoretical realized bandwidth of 8GB/s simultaneously per

direction, for an aggregate of 16GB/s totally.

- PCI-Express supports a raw bit-rate of 5.0Gb/s on the data pins.

- 2X bandwidth over the PCI-Express 1.1 architecture.

PEX16_1

PCI1~PCI2: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for expansion

cards. This PCI slot is designated as 32 bits.

PCI1

PCI2

A780L3L

13

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is

placed on pins, the jumper is “close”, if not, that means the jumper is

“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and

speaker connection. It allows user to connect the PC case’s front panel switch

functions.

1

8

16

PW R_LED

On/Off

RST

HLED

SPK

++

+

9

-

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A

2 N/A 10 N/A

N/A

3 N/A 11 N/A N/A

4 Speaker

Speaker

Connector

12 Power LED (+)

5 HDD LED (+) 13 Power LED (+)

6 HDD LED (-)

Hard drive

LED

14 Power LED (-)

Power LED

7 Ground 15 Power button

8 Reset control

Reset button

16 Ground

Power-on button

Motherboard Manual

14

F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel

These headers allow user to connect additional USB cable on the PC front panel,

and also can be connected with internal USB devices, like USB card reader.

Assignment

1 +5V (fused)

2 +5V (fused)

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 NC

19

210

FUSB_1

FUSB_2

10 Key

JCMOS1: Clear CMOS Header

Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and

the CMOS data.lPease carefully follow the procedures to avoid damaging the

motherboard.

13

Pin 1-2 Close:

Normal Operation (default).

13

Pin 2-3 Close:

Clear CMOS data.

Clear CMOS Procedures:※

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

A780L3L

15

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front

panel. This header allows only HD audio front panel connector; AC’97 connector

is not acceptable.

Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

6 Jack Sense

7 Front Sense

8 Key

9 Left line in

19

210

10 Jack Sense

JSPDIFOUT1: Digital Audio-out Connector

This connector allows user to connect the PCI bracket SPDIF output header.

Assignment

1 +5V

2 SPDIF_OUT

13

3 Ground

Motherboard Manual

16

J_PRINT1: Printer Port Connector

This header allows you to connector printer on the PC.

125

2

26

Pin Assignment Pin Assignment

1 -Strobe 14 Ground

2 -ALF 15 Data 6

3 Data 0 16 Ground

4 -Error 17 Data 7

5 Data 1 18 Ground

6 -Init 19 -ACK

7 Data 2 20 Ground

8 -Scltin 21 Busy

9 Data 3 22 Ground

10 Ground 23 PE

11 Data 4 24 Ground

12 Ground 25 SCLT

13 Data 5 26 Key

J_COM1: Serial port Connector

The motherboard has a Serial Port Connector for connecting RS-232 Port.

Assignment

1 Carrier detect

2 Received data

3 Transmitted data

4 Data terminal ready

5 Signal ground

6 Data set ready

7 Request to send

8 Clear to send

9 Ring indicator

1

2

10

9

10 NC

A780L3L

17

JUSBV1/JUSBV2: Power Source Headers for USB Ports

Pin 1-2 Close:

JUSBV1: +5V for USB ports at USB1/RJ45USB1.

JUSBV2: +5V for USB ports at front panel (F_USB1/F_USB2).

Pin 2-3 Close:

JUSBV1: +5V STB for USB ports at USB1/RJ45USB1.

JUSBV2: +5V STB for USB ports at front panel (F_USB1/F_USB2).

13

3

1

Pin 1-2 close

13

3

1

JUSBV2

JUSBV1

13

3

1

Pin 2-3 close

Motherboard Manual

18

CHAPTER 4: RAID FUNCTIONS

4.1 O

PERATING SYSTEM

z Supports Windows XP , Windows Vista, and Windows 7.

4.2 RAID ARRAYS

RAID supports the following types of RAID arrays:

RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for

many applications.

RAID 1: RAID 1 defines techniques for mirroring data.

RAID 1+0: RAID 1+0 combines the techniques used in RAID 0 and RAID 1.

4.3 HOW RAID WORKS

RAID 0:

The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks

up a large file into smaller blocks and performs disk reads and writes across multiple

drives in parallel. The size of each block is determined by the stripe size parameter,

which you set during the creation of the RAID set based on the system environment.

This technique reduces overall disk access time and offers high bandwidth.

Features and Benefits

- Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the

platform.

- Uses: Intended for non-critical data requiring high data throughput, or any

environment that does not require fault tolerance.

- Benefits: provides increased data throughput, especially for large files.

No capacity loss penalty for parity.

- Drawbacks: Does not deliver any fault tolerance. If any drive in the array

fails, all data is lost.

- Fault Tolerance: No.

Block 1

Block 3

Block 5

Block 2

Block 4

Block 6

La pagina sta caricando ...

Biostar A740G3L - BIOS Setup Manual

Questo manuale è adatto anche per

Biostar A740G3L - BIOS Setup Manual

in altre lingue

Documenti correlati

Altri documenti