Hangar 9 HAN5260 Manuale del proprietario

Cub Crafters XCub 60cc

Instruction Manual

Bedienungsanleitung

Manuel d’utilisation

Manuale di Istruzioni

2

Part # English Deutsch Français Italiano

 REPLACEMENT PARTS • ERSATZTEILE • PIÈCES DE RECHANGE • PEZZI DI RICAMBIO

A

HAN526001 Fuselage Rumpf Fuselage Fusoliera

B

HAN526002 Left Wing with Aileron and Flap Tragﬂ äche Links mit Querruder und Klappe Aile gauche avec aileron et volet Semiala sinistra con alettone e ﬂ ap

C

HAN526003 Right Wing with Aileron and Flap Tragﬂ äche Rechts mit Querruder und Klappe Aile droite avec aileron et volet Semiala destra con alettone e ﬂ ap

D

HAN526004 Stabilizer and Elevator Set Höhenruderset Set Plan horizontal et Gouverne de profondeur Set stabilizzatore ed elevatore

E

HAN526005 Rudder Seitenleitwerk Gouverne de direction Timone

F

HAN526006 Cowling Motorhaube Capot moteur Carenatura

G

HAN526007 Hardware Pack Kleinteilepaket Sachet d’accessoires Viti e accessori

H

HAN526008 Engine Mount Set Motor-Montagesatz Jeu de renfort moteur Set di montaggio motore

I

HAN526009 Wing Struts Set (Left and Right) Tragﬂ ächenstreben (Links und Rechts) Jeu d’entretoises d’aile (Gauche et Droite) Set montanti ala (destro e sinistro)

J

HAN526010 Pushrod Set Gestänge / Anlenkungen Set Jeu de tringleries Set dell’asta di spinta

K

HAN526011 Window Set Fenster Set Jeu de fenêtres Set ﬁ nestrature

L HAN526012 EP Mount Set E-Motorhalter Set Jeu de renforts moteur EP Set di montaggio motore elettrico

M

HAN526013 Aerotow Release Flugzeugschlepp-Freigabe Dégagement de la remorque Dispositivo di sgancio dell’aerotraino

N

HAN526014 Super Scale Tailwheel Super-maßstabsgetreues Spornrad Roue de queue à échelle de précision Ruotino di coda in super scala

0 HAN526016 Gas Tank (20oz) Kraftstofftank (591cc) Réservoir essence (591cc) Serbatoio combustibile (591cc)

P

HAN526017 Landing Gear Set Fahrwerk Set Train d’atterrissage Set del carrello di atterraggio

Q

HAN526018 Wing Tube Tragﬂ ächenverbinder Clé d’aile Tubo dell’ala

R

HAN526019 Decal Set Dekorbogen Planche de décoration Set di decalcomanie

S

HAN526020 Spinner Spinner Cône Ogiva dell’elica

T

HAN526021 Fiberglass Fairings Glasfaser-Verkleidung Carénages en ﬁ bre de verre Carenature in vetroresina

U

HAN526023 2x Seats and Antenna 2X Sitze und Antenne 2x sièges et antenne 2x sedili e antenna

V

HAN526024 Sprung U/C Feder U/C Ressorts U/C Carrello di atterraggio ammortizzato

W

SUL887S Sky Airﬂ ight Wheel with Treads 7-inch Sky Airﬂ ight Rad mit Gewinde 18cm (7 Zoll) Roue SkyAirﬂ ight avec bandes 18cm (7po) Ruota Sky Airﬂ ight con ﬁ letti 7’’

116.0 in (294 cm)

1908 sq in (123.1 dm2) Total

82 in (208 cm)

27–31 lbs (12.0–14.5 kg)

 SPECIFICATIONS • SPEZIFIKATIONEN • SPÉCIFICATIONS • SPECIFICHE

2-Stroke Gas: 50cc–70cc, 4-Stroke gas/petrol: 61cc

2-Takt Benziner: 50cc–70cc, 4-Takt Benzin: 61 cc

2 temps Essence: 50cc–70cc, 4 temps essence: 61cc

2-Tempi Gas: 50cc–70cc, 4 tempi benzina: 61 cc

Electric Power: Power 360, 180Kv Brushless

Elektro Antrieb Power: Power 360, 180Kv Brushless

Moteur électrique (EP): Power 360, 180Kv Brushless

Motore elettrico: Power 360, 180Kv Brushless

5-channel (or greater) with 5 servos

5-Kanal (oder größer) mit 5-Servos

5 voies (ou plus) avec 5 servos

a 5 canali (o più) con 5 servo

Spinner: 4-inch (Included)

Spinner: 102mm (Enthalten)

Cône: 102mm (Fourni)

Ogiva dell’elica: 102mm (Inclusa)

7

1

/

2

inches (190.5mm)

3

Cub Crafters XCub 60cc

Part # English Deutsch Français Italiano

 REQUIRED RADIO EQUIPMENT • ERFORDERLICHE RC AUSRÜSTUNG • ÉQUIPEMENT RADIO REQUIS • APPARECCHIATURE RADIO NECESSARIE

DUB671 Super Strength Long Servo Arm: JR Hochfester langer Servoarm: JR Long bras de servo robuste: JR Braccio servo lungo ultra resistente: JR

EFLRYH9TR Triple Plug Y Harness Y-Kabelbaum mit Dreifach-Stecker Harnais en Y à triple prise Cablaggio a Y tripla presa

SPMA3005 Heavy-Duty Servo Extension 24-inch Servokabelverlängerung 600 mm (24 inch) Rallonge de servo, 600 mm Estensione servo 24 pollici

SPMA3006 Heavy-Duty Servo Extension 36-inch Servokabelverlängerung 920 mm (36 inch) Rallonge de servo, 920 mm Estensione servo 36 pollici

SPMA3054 Servo Connector Clips (25) Servosteckerklemmen (25) Attaches de connexion du servo (25) Morsetti servocomando (25)

SPMAR12310T AR12310T 12CH PowerSafe Tele RX AR12310T PowerSafe Tele RX mit 12 Kanälen PowerSafe Tele RX 12canaux AR12310T PowerSafe Tele RX 12 canali AR12310T

SPMSA6320 A6320 H-T/H-S BrushlessHV Servo A6320 H-T/H-S bürstenloser HV-Servo Servo A6320 H-T/H-S BrushlessHV Servo brushless HV H-T/H-S A6320

HAN9151 Aluminum Sx Arm, 1 inch SPM JR Aluminium Sx Arm, 25,4mm (1 Zoll) SPM JR Bras Sx en aluminium, JP SPM 25,4mm (1po) Braccio alluminio sx, 1’’, SPM JR

SPMA3041 HD Male to Male Extension 6 inch HD Stecker-Stecker-Verlängerung 15 cm (6 Zoll) Extension mâle-mâle HD 15 cm (6po) Prolunga HD maschio-maschio 6’’

SPMEXEC312 12 inch EC3 Extension with 16AWG 30cm (12 Zoll) EC3-Verlängerung mit 16AWG Extension EC3 30 cm (12po) avec 16AWG Prolunga EC3 12’’ con 16AWG

 2-STROKE GAS • 2-TAKT BENZINER • 2 TEMPS ESSENCE • 2-TEMPI A BENZINA

DUB800

Tygon

®

Gas Tubing, 3’ Large

Tygon

®

Gasleitung, 91cm (3 Fuß) groß Tubulure de gaz Tygon

®,

large, 91 cm (3pi) Tubi per combustibile Tygon

®

, diametro 3’

EVOA112 Evolution 3 Wire Ignition/Receiver Switch Evolution Zündschalter Interrupteur Evolution 3 ﬁ ls Allumage/RX

Evolution, interruttore a 3 ﬁ li accensione/

ricevitore

EVOE62GX 62GX 62cc Gas/Petrol Engine 62GX 62cm³ Gas/Benzinmotor Moteur à gaz/essence 62GX 62cc Motore benzina 62GX 62cc

HAN116 Fuel Filler with “T” and Overﬂ ow Fitting Hangar 9 Tanknippel mit T Stück u. Überlauf Fitting Point de remplissage de carburant avec coupleur en T Bocchettone di riempimento carburante con

SPMA3002 Heavy-Duty Servo Extension 9-inch Servokabelverlängerung 230 mm (9 inch) Rallonge de servo, 230 mm Estensione servo 9 pollici

SPMB4000LPRX 4000mAh 2S 7.4V LiPo Receiver Battery LiPo-Empfängerakku (7,4 V / 4000 mAh) Batterie Li-Po de récepteur 7,4 V 4000 mAh Batteria per ricevitore da 7,4 V Li-Po, 4.000 mAh

SPMSA6110 A6110 HV Standard Servo A6110 HV Standard Servo Servo standard A6110 HV Servo standard A6110 HV

 ELECTRIC POWER • ELEKTROANTRIEB • MOTEUR ELECTRIQUE (EP) • MOTORE ELETTRICO

CSE010010300 Edge 160HV 50V ESC 010-0103-00

Edge 160HV 50V Geschwindigkeitsregler

010-0103-00

Variateur ESC Edge 160HV 50V 010-0103-00 ESC Edge 160HV 50V 010-0103-00

CSE010000401 Castle BEC PRO V2, 010-0004-01 Castle BEC PRO V2, 010-0004-01 Castle BEC PRO V2, 010-0004-01 Castle BEC PRO V2, 010-0004-01

EFLAEC508 EC5 Batt Series Harness, 10Awg EC5 Akku-Serie Kabelbaum, 10AWG Harnais de batteries EC5, 10AWG EC5 collegamento in serie delle batterie, 10Awg

EFLM4360A Power 360 BL Outrunner Motor,180Kv Power 360 bürstenloser Außenläufer-Motor,180Kv Moteur à cage tournante sans balais Power 360, 180K Motore outrunner BL Power 360,180K

KXSB70006S30 F-Tek 7000mAh 6S 22.2V 30C, EC5 F-Tek 7000mA 6S 22,2V 30C, EC5 EC5 F-Tek 7000mAh 6S 22,2V 30C F-Tek 7000mAh 6S 22,2V 30C, EC5

SPMB4000LPRX 4000mAh 2S 7.4V LiPo Receiver Battery LiPo-Empfängerakku (7,4 V / 4000 mAh) Batterie Li-Po de récepteur 7,4 V 4000 mAh Batteria per ricevitore da 7,4 V Li-Po, 4.000 mAh

 REQUIRED ADHESIVES • ERFORDERLICHE KLEBSTOFFE • TYPES DE COLLES • ADESIVI NECESSARI

DLMAD44 Roket Rapid CA 5-10 sec: 20g Roket Rapid CA 5-10 s: 20g Colle cyano Roket Rapid 5-10 sec: 20g Colla cianoacrilica Roket Rapid 5-10 sec: 20 g

DLMAD45 Roket Max CA 10-20 sec: 20g Roket Max CA 10-20 s: 20g Colle cyano Roket Max 10-20 sec: 20g Colla cianoacrilica Roket Max 10-20 sec: 20 g

PAAPT715 CA Accelerator Sekundenkleber (CA) Aktivator Accélérateur de colle CA Accelerante colla CA

PAAPT37 5-Minute Epoxy 5 Minuten Epoxy Époxy 5 minutes Colla epossidica 5 minuti

PAAPT35 15-Minute Epoxy 15 Minuten Epoxy Époxy 15 minutes Colla epossidica 15 minuti

PAAPT39 30-Minute Epoxy 30 Minuten Epoxy Époxy 30 minutes Colla epossidica 30 minuti

PAAPT42 Threadlock Schraubensicherungslack Frein-ﬁ let Frenaﬁ letti

DLMAD12 R/C Modeller Canopy Glue: 4 oz R/C Modeller Kanzelkleber: 113,4g (4 oz) Colle à verrière R/C Modeller: 113g Colla per capottine R/C Modeller: 4 oz

4

Part # English Deutsch Français Italiano

 REQUIRED TOOLS • BENÖTIGTES WERKZEUG • OUTILS REQUIS • ATTREZZI NECESSARI

Box wrench: 12mm, 1/2-inch Ringschlüssel: 12mm, 1/2-inch Clé hexagonales: 12mm, 1/2-inch Chiavi: 12mm, 1/2-inch

Drill Bohrer Mini-perceuse Trapano

Drill bits: 5/64-inch, 3/32-inch, 7/64-inch,

1/8-inch, 9/64-inch, 3/16-inch

Bohrer: 1,5 mm, 2mm, 2,5mm, 3mm, 3,5mm, 5mm Forêt : 1,5 mm, 2mm, 2,5mm, 3mm, 3,5mm, 5mm

Punte per trapano: 1,5 mm, 2mm, 2,5mm, 3mm,

3,5mm, 5mm

Epoxy brush Pinsel Pinceau Epoxy Spazzole epoxy

Felt-tipped pen Faserstift Feutre ﬁ n effaçable Pennarello

Flat blade screwdriver, small and large Schraubendreher ﬂ ach Tournevis plat, petit et grand Cacciavite a lama piatta: piccolo, grande

Flat ﬁ le Flachfeile Lime plate Lima piatta

Hemostats Klemme Pince Hemostat Pinzetta

Hex wrench: 1.5mm, 2mm, 2.5mm, 3mm,

4mm, 5mm, 6mm, 3/32-inch

Inbusschlüssel: 1,5mm, 2mm, 2.5mm, 3mm, 4mm,

5mm, 6mm, 3/32-inch

Tournevis hexagonal : 1,5mm, 2mm, 2.5mm, 3mm,

4mm, 5mm, 6mm, 3/32-inch

Chiave esag.: 1,5mm, 2mm, 2.5mm, 3mm, 4mm,

5mm, 6mm, 3/32-inch

Hobby knife with #11 blade Hobbymesser mit # 11 Klinge Couteau : Lame numéro 11 Taglierino: #11 lama

Hobby scissors Hobbyschere Ciseaux Forbici per hobby

Hook and loop strap and tape Klettband Bande auto aggripante Nastro e fascette

Isopropyl alcohol Isopropyl Alkohol Alcool isopropylique Alcol isopropilico

Low-tack tape Kreppband Adhésif de masquage Nastro a bassa aderenza

Mixing cups and sticks Mischbecher und Rührstäbchen Récipients pour mélanger et bâtons Contenitori e stick per mixer colla

Needle nose pliers Spitzzange Pince ﬁ ne Pinze a becco stretto

Nut driver: 5mm, 5.5mm, 10mm, 1/4-inch Steckschlüssel. 5mm, 5.5mm, 10mm, 1/4-inch Clés à douilles : 5mm, 5.5mm, 10mm, 1/4-inch Chiave per dadi: 5mm, 5.5mm, 10mm, 1/4-inch

Paper towels Papiertücher Papier absorbant Asciugamani di carta

Pencil Stift Crayon à papier Matita

Phillips screwdriver: #1, #2 Phillips Schraubendreher: #1,#2 Tournevis cruciforme: #1, #2 Cacciavite a croce: #1, #2

Pin vise Handbohrer Porte forets Trapano manuale

Ruler Lineal Réglet Righello

Sandpaper, medium grit Schleifpapier Papier de verre Carta vetrata

Scissors Schere Ciseaux Forbici

Side cutters Seitenschneider Pince coupante Lama laterale

 OPTIONAL ITEMS • OPTIONALE TEILE • ÉLÉMENTS OPTIONNELS • ARTICOLI OPZIONALI

EVOA100 Optical Ignition Kill Switch Optischer Zünd-Notausschalter Coupe-circuit optique d’allumage Sezionatore ottico accensione

SPMA3000 Heavy-Duty Servo Extension 3-inch Servokabelverlängerung 75 mm (3 inch) Rallonge de servo, 75 mm Estensione servo 3 pollici

SPMAS3000 AS3000 AS3X Stabilization Module AS3000 AS3X Stabilisierungsmodul Module de stabilisation AS3000 AS3X Modulo di stabilizzazione AS3000 AS3X

WGT111

Extreme Big Tote,82 x 24 x 3 inches, Red &

Black

Extreme Big Tote, 208 x 60 x 7cm (82 x 24 x 3 Zoll), rot

und schwarz

Grand sac Extrême, 210 x 60 x 10 cm (82 x 24 x 3po),

rouge et noir

Borsa tote Extreme grande, 82 x 24 x 3’’, rossa

e nera

5

Cub Crafters XCub 60cc

 OPTIONAL SCALE ACCESSORIES

We have worked with various vendors to develop scale

details speciﬁ cally for this model. These items include

pilot ﬁ gures, decals, propellers, wheels and shocks.

Pilots:

www.tailoredpilots.com

www.warbirdpilots.com

Wheels, axles and shocks:

www.prbushwheels.com

Scale instrument panels:

www.iﬂ ytailies.com

Custom markings and decals:

www.callie-graphics.com

Scale Propellers:

www.aircraftinternational.com

 OPTIONALES MASSSTABSGETREUES

ZUBEHÖR

Wir haben mit verschiedenen Anbietern

zusammengearbeitet, um maßstabsgetreue Einzelteile

speziell für dieses Modell zu entwickeln. Zu diesen

Einzelteilen zählen Pilotenﬁ guren, Decals, Propeller, Räder

und Stoßdämpfer.

Piloten:

www.tailoredpilots.com

www.warbirdpilots.com

Räder, Achsen und Stoßdämpfer:

www.prbushwheels.com

Maßstabsgetreue Instrumententafeln:

www.iﬂ ytailies.com

Kundenspeziﬁ sche Markierungen und Decals:

www.callie-graphics.com

Maßstabgetreue Propeller:

www.aircraftinternational.com

 ACCESSOIRES À ÉCHELLE FACULTATIFS

Nous avons collaboré avec plusieurs fournisseurs pour

développer des détails à échelle spéciﬁ quement pour

ce modèle. Notamment des ﬁ gurines de pilote, des

autocollants, des hélices, des roues et des amortisseurs.

Pilotes:

www.tailoredpilots.com

www.warbirdpilots.com

Roues, axes et amortisseurs:

www.prbushwheels.com

Panneaux d’instrument à échelle:

www.iﬂ ytailies.com

Marquages et autocollants personnalisés:

www.callie-graphics.com

Hélices à échelle:

www.aircraftinternational.com

 ACCESSORI IN SCALA OPZIONALI

Abbiamo collaborato con diversi fornitori per sviluppare

dettagli in scala pensati appositamente per questo

modello. Gli articoli includono piloti in miniatura,

decalcomanie, eliche, ruotini e ammortizzatori.

Piloti:

www.tailoredpilots.com

www.warbirdpilots.com

Ruotini, assali e ammortizzatori:

www.prbushwheels.com

Pannelli degli strumenti in scala:

www.iﬂ ytailies.com

Contrassegni e decalcomanie personalizzati:

www.callie-graphics.com

Eliche in scala:

www.aircraftinternational.com

6

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon

Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

The following terms are used throughout the product literature to indicate various levels of potential harm when

operating this product:

Meaning of Special Language

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage,

and serious injury OR create a high probability of superﬁ cial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a

possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or

no possibility of injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.

Failure to operate the product correctly can result in damage to the product, personal property and cause serious

injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic

mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage

to the product or other property. This product is not intended for use by children without direct adult supervision. Do

not attempt disassembly, use with incompatible components or augment product in any way without the approval

of Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to

read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate

correctly and avoid damage or serious injury.

AGE RECOMMENDATION: NOT FOR CHILDREN UNDER 14 YEARS. THIS IS NOT A TOY.

 USING THE MANUAL

This manual is divided into sections to help make assembly easier to understand.

 SAFETY WARNINGS AND PRECAUTIONS

Read and follow all instructions and safety precautions before use. Improper use can result in ﬁ re, serious injury and

damage to property.

Components

Use only with compatible components. Should any compatibility questions exist, please refer to the product

instructions, component instructions or contact the appropriate Horizon Hobby ofﬁ ce.

Flight

Fly only in open areas to ensure safety. It is recommended ﬂ ying be done at radio control ﬂ ying ﬁ elds. Consult local

ordinances before choosing a ﬂ ying location.

Propeller

Keep loose items that can become entangled in the propeller away from the prop. This includes loose clothing or other

objects such as pencils and screwdrivers. Keep your hands away from the propeller as injury can occur.

Batteries

Always follow the manufacturer’s instructions when using and disposing of any batteries. Mishandling of Li-Po

batteries can result in ﬁ re causing serious injury and damage.

Small Parts

This kit includes small parts and should not be left unattended near children as choking and serious injury could result.

 SAFE OPERATING RECOMMENDATIONS

• Inspect your model before every ﬂ ight to ensure it is airworthy.

• Be aware of any other radio frequency user who may present an interference problem.

• Always be courteous and respectful of other users in your selected ﬂ ight area.

• Choose an area clear of obstacles and large enough to safely accomodate your ﬂ ying activity.

• Make sure this area is clear of friends and spectators prior to launching your aircraft.

• Be aware of other activities in the vicinity of your ﬂ ight path that could cause potential conﬂ ict.

• Carefully plan your ﬂ ight path prior to launch.

• Abide by any and all established AMA National Model Aircraft Safety Code.

 BEFORE STARTING ASSEMBLY

• Remove parts from bag.

• Inspect fuselage, wing panels, rudder and stabilizer for damage.

• If you ﬁ nd damaged or missing parts, contact your place of purchase.

• Charge transmitter and receiver batteries.

• Center trims and sticks on your transmitter.

• For a computer radio, create a model memory for this particular model.

• Bind your transmitter and receiver, using your radio system’s instructions.

IMPORTANT: Rebind the radio system once all control throws are set. This will keep the servos from moving to

their endpoints until the transmitter and receiver connect. It will also guarantee the servo reversal settings are

saved in the radio system.

 FAA INFORMATION

If you own this product, you may be required to register with the FAA.

For up-to-date information on how to register with the FAA, please visit https://registermyuas.faa.gov/.

For additional assistance on regulations and guidance on UAS usage, visit knowbeforeyouﬂ y.org/.

 BUILDING PRECAUTIONS

During assembly, we recommend resting the parts on a soft surface such as a soft towel to help prevent denting the

sheeting.

7

Cub Crafters XCub 60cc

Propeller

Halten Sie lose Gegenstände die sich im Propeller verfangen können weg vom Propeller. Dieses gilt auch für Kleidung

oder andere Objekte wie zum Beispiel Stifte oder Schraubendreher.

Halten Sie ihre Hände weg vom Propeller, es besteht akute Verletzungsgefahr.

Akkus

Folgen Sie immer den Herstelleranweisungen bei dem Gebrauch oder Entsorgung von Akkus. Falsche Behandlung von

LiPo Akkus kann zu Feuer mit Körperverletzungen und Sachbeschädigung führen.

Kleinteile

Dieser Baukasten beinhaltet Kleinteile und darf nicht unbeobachtet in der Nähe von Kindern gelassen werden, da die

Teile verschluckt werden könnten mit ernsthaften Verletzung zur Folge.

 EMPFEHLUNGEN ZUM SICHEREN BETRIEB

• Überprüfen Sie zur Flugtauglichkeit ihr Modell vor jedem Flug.

• Beachten Sie andere Piloten deren Sendefrequenzen ihre Frequenz stören könnte.

• Begegnen Sie anderen Piloten in ihrem Fluggebiet immer höﬂ ich und respektvoll.

• Wählen Sie ein Fluggebiet, dass frei von Hindernissen und groß genug ist.

• Stellen Sie vor dem Start sicher, dass die Fläche frei von Freunden und Zuschauern ist.

• Beobachten Sie den Luftraum und andere Flugzeuge/Objekte die ihren Flugweg kreuzen und zu einem Konﬂ ikt

führen könnten.

• Planen Sie sorgfältig ihren Flugweg vor dem Start.

 VOR DEM ZUSAMMENBAU

• Entnehmen Sie zur Überprüfung jedes Teil der Verpackung.

• Überprüfen Sie den Rumpf, Tragﬂ ächen, Seiten- und Höhenruder auf Beschädigung.

• Sollten Sie beschädigte oder fehlende Teile feststellen, kontaktieren Sie bitte den Verkäufer.

• Laden des Senders und Empfängers.

• Zentrieren der Trimmungen und Sticks auf dem Sender.

• Sollten Sie einen Computersender verwenden, resetten Sie einen Speicherplatz und benennen ihn nach dem Modell.

• Sender und Empfänger jetzt nach den Bindeanweisung des Herstellers zu binden.

WICHTIG: Wir empfehlen dringend nachdem alle Einstellungen vorgenommen worden sind, das Modell neu zu binden.

Dieses verhindert, dass die Servos in die Endanschläge laufen bevor sich Sender und Empfänger verbunden haben. Es

garantiert auch, dass die Servoreverseeinstellungen in der RC Anlage gesichert sind.

 HINWEISE ZUM BAU

Während des Zusammenbaus empfehlen wird, dass die Teile auf einer weichen Oberﬂ äche, wie einem Handtuch,

abgelegt werden, um ein Eindrücken der Bleche zu verhindern.

HINWEIS

Alle Anweisungen, Garantien und anderen zugehörigen Dokumente können im eigenen Ermessen von Horizon Hobby,

LLC. jederzeit geändert werden Die aktuelle Produktliteratur ﬁ nden Sie auf horizonhobby.com unter der Registerkarte

„Support“ für das betreffende Produkt.

Spezielle Bedeutungen

Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe

Gefahrenrisiken beim Betrieb dieses Produkts hinzuweisen:

WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden,

Kollateralschäden und schwere Verletzungen ODER mit hoher Wahrscheinlichkeit oberﬂ ächliche Verletzungen.

ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden UND die

Gefahr von schweren Verletzungen.

HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND geringe

oder keine Gefahr von Verletzungen ergeben.

WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem Betrieb mit den Produktfunktionen

vertraut zu machen. Wird das Produkt nicht korrekt betrieben, kann dies zu Schäden am Produkt oder persönlichem

Eigentum führen oder schwere Verletzungen verursachen.

Dies ist ein hochentwickeltes Hobby-Produkt. Es muss mit Vorsicht und gesundem Menschenverstand betrieben

werden und benötigt gewisse mechanische Grundfähigkeiten. Wird dieses Produkt nicht auf eine sichere und

verantwortungsvolle Weise betrieben, kann dies zu Verletzungen oder Schäden am Produkt oder anderen Sachwerten

führen. Dieses Produkt eignet sich nicht für die Verwendung durch Kinder ohne direkte Überwachung eines

Erwachsenen. Verwenden Sie das Produkt nicht mit inkompatiblen Komponenten oder verändern es in jedweder Art

ausserhalb der von Horizon Hobby, LLC vorgegebenen Anweisungen. Diese Bedienungsanleitung enthält Anweisungen

für Sicherheit, Betrieb und Wartung. Es ist unbedingt notwendig, vor Zusammenbau, Einrichtung oder Verwendung

alle Anweisungen und Warnhinweise im Handbuch zu lesen und zu befolgen, damit es bestimmungsgemäß betrieben

werden kann und Schäden oder schwere Verletzungen vermieden werden.

NICHT GEEIGNET FÜR KINDER UNTER 14 JAHREN. DIES IST KEIN SPIELZEUG.

 ÜBER DIESE ANLEITUNG

Diese Anleitung ist zur Vereinfachung des Zusammenbaues in Sektionen unterteilt.

 WARNUNGEN UND SICHERHEITS-VORKEHRUNGEN

Bitte lesen und befolgen Sie alle Anweisungen und Sicherheitsvorkehrungen vor dem Gebrauch. Falscher, nicht

sachgemäßer Gebrauch kann Feuer, ernsthafte Verletzungen und Sachbeschädigungen zur Folge haben.

Komponenten

Verwenden Sie mit dem Produkt nur kompatible Komponenten. Sollten Fragen zur Kompatibilität auftreten, lesen Sie

bitte die Produkt- oder Bedienungsanweisung oder kontaktieren den Service von Horizon Hobby.

Fliegen

Fliegen Sie um Sicherheit garantieren zu können, nur in weiten offenen Gegenden. Wir empfehlen hier den Betrieb auf

zugelassenen Modellﬂ ugplätzen. Bitte beachten Sie lokale Vorschriften und Gesetze, bevor Sie einen Platz zum Fliegen

wählen.

8

L’hélice

Gardez éloignés tous les éléments qui pourraient être attrapés par l’hélice. Cela inclut les vêtements larges ou les

objets comme des outils par exemple. Gardez toujours vos mains à distance pour éviter tout cas de blessures.

Les batteries

Suivez toujours les instructions du fabricant de vos batteries. Une mauvaise manipulation d’une batterie Li-Po peut

entraîner un incendie causant de graves dégâts matériels et des blessures corporelles.

Petites pièces

Ce kit contient des petites pièces qui ne doivent pas être laissées à la portée des enfants, ces pièces sont dangereuses

pour eux et peuvent entraîner de graves blessures.

 CONSIGNES DE SÉCURITÉ CONCERNANT L’UTILISATION

• Inspectez votre modèle avant chaque vol.

• Surveillez les fréquences utilisées à proximité.

• Soyez toujours courtois et respectueux des autres utilisateurs de la zone de vol.

• Choisissez une zone dégagée de tout obstacle et sufﬁ samment grande pour voler en toute sécurité.

• Contrôlez que la zone est libre de spectateurs avant de lancer votre modèle.

• Soyez conscient des autres activités aux alentours de votre vol, risque de conﬂ it potentiel.

• Planiﬁ ez votre vol avant de le commencer.

 AVANT DE COMMENCER L’ASSEMBLAGE

• Retirez toutes les pièces des sachets pour les inspecter.

• Inspectez soigneusement le fuselage, les ailes et les empennages.

• Si un élément est endommagé, contactez votre revendeur.

• ll est recommandé de préparer tous les éléments du système de la radio.

• Cela inclut la charge des batteries comme la mise au neutre des trims et des manches de votre émetteur.

• Si vous utilisez une radio programmable, sélectionnez une mémoire libre aﬁ n d’y enregistrer les paramètres de ce

modèle.

• Nous vous recommandons d’affecter maintenant le récepteur à l’émetteur en suivant les instructions fournies avec

votre radio.

IMPORTANT: Il est hautement recommandé de ré-affecter le système une fois que les courses seront réglées. Cela

empêchera les servos d’aller en butée lors de la connexion du système. Cela garantit également que la direction des

servos est enregistrée dans l’émetteur.

 PRÉCAUTIONS D’ASSEMBLAGE

Lors de l’assemblage de votre modèle, nous vous recommandons de poser les pièces sur une surface douce comme

une serviette douce pour éviter d’abîmer l’entoilage.

REMARQUE

La totalité des instructions, garanties et autres documents est sujette à modiﬁ cation à la seule discrétion d’Horizon

Hobby, LLC. Pour obtenir la documentation àjour, rendez-vous sur le site horizonhobby.com et cliquez sur l’onglet de

support de ce produit.

Signiﬁ cation de certains termes spéciﬁ ques

Les termes suivants sont utilisés dans l’ensemble du manuel pour indiquer différents niveaux de danger lors de

l’utilisation de ce produit:

AVERTISSEMENT: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels

et des blessures graves OU engendrer une probabilité élevée de blessure superﬁ cielle.

ATTENTION: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels ET des

blessures graves.

REMARQUE: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels ET

éventuellement un faible risque de blessures.

AVERTISSEMENT: Lisez la TOTALITÉ du manuel d’utilisation aﬁ n de vous familiariser avec les caractéristiques du

produit avant de le faire fonctionner. Une utilisation incorrecte du produit peut entraîner sa détérioration, ainsi que des

risques de dégâts matériels, voire de blessures graves.

Ceci est un produit de loisirs sophistiqué. Il doit être manipulé avec prudence et bon sens et requiert des aptitudes

de base en mécanique. Toute utilisation irresponsable de ce produit ne respectant pas les principes de sécurité peut

provoquer des blessures, entraîner des dégâts matériels et endommager le produit. Ce produit n’est pas destiné à

être utilisé par des enfants sans la surveillance directe d’un adulte. N’essayez pas de modiﬁ er ou d’utiliser ce produit

avec des composants incompatibles hors des instructions fournies par Horizon Hobby, LLC. Ce manuel comporte des

instructions relatives à la sécurité, au fonctionnement et à l’entretien. Il est capital de lire et de respecter la totalité

des instructions et avertissements du manuel avant l’assemblage, le réglage et l’utilisation, ceci aﬁ n de manipuler

correctement l’appareil et d’éviter tout dégât matériel ou toute blessure grave.

14 ANS ET PLUS. CECI N’EST PAS UN JOUET.

 UTILISATION DU MANUEL

Ce manuel est divisé en sections pour vous aider à comprendre plus facilement l’assemblage.

 AVERTISSEMENTS RELATIFS À LA SÉCURITÉ

Lisez et suivez toutes les instructions relatives à la sécurité avant utilisation. Une utilisation inappropriée peut entraîner

un incendie, de graves blessures et des dégâts matériels.

Composants

Utilisez uniquement des composants compatibles. Si vous avez des questions concernant la compatibilité, référez-vous

à ce manuel ou contactez le service technique Horizon Hobby.

Le vol

Volez uniquement dans des zones dégagées pour un maximum de sécurité. Il est recommandé d’utiliser les pistes des

clubs d’aéromodélisme. Consultez votre mairie pour connaître les sites autorisés.

9

Cub Crafters XCub 60cc

AVVISO

Tutte le istruzioni, le garanzie e gli altri documenti pertinenti sono soggetti a cambiamenti a totale discrezione di

Horizon Hobby, LLC. Per una documentazione aggiornata sul prodotto, visitare il sito www.horizonhobby.com e fare

clic sulla sezione Support per questo prodotto.

Signiﬁ cato dei termini particolari

In tutta la documentazione relativa al prodotto sono utilizzati iseguenti termini per indicare vari livelli di potenziale

pericolo durante il funzionamento:

AVVERTENZA: Procedure che, se non debitamente seguite, espongono alla possibilità di danni alla proprietà ﬁ sica

opossono omportare un’elevata possibilità di provocare ferite superﬁ ciali. Ulteriori precauzioni per la sicurezza e

avvertenze.

ATTENZIONE: Procedure che, se non sono seguite correttamente, possono creare danni materiali E possibili gravi

lesioni.

AVVISO: Procedure che, se non sono seguite correttamente, possono creare danni materiali E nessuna oscarsa

possibilità di lesioni.

AVVERTENZA: Leggere TUTTO il manuale di istruzioni e prendere familiarità con le caratteristiche del prodotto, prima

di farlo funzionare. Un utilizzo scorretto del prodotto può causare danni al prodotto stesso, alle persone oalle cose,

provocando gravi lesioni.

Questo è un prodotto di hobbistica soﬁ sticato e NON un giocattolo. È necessario farlo funzionare con cautela e

responsabilità e avere conoscenze basilari di meccanica. Se questo prodotto non è utilizzato in maniera sicura e

responsabile potrebbero veriﬁ carsi lesioni odanni al prodotto stesso oad altre proprietà. Non è un prodotto adatto

aessere utilizzato dai bambini senza la diretta supervisione di un adulto. Non usare componenti non compatibili

o alterare il prodotto in nessuna maniera al di fuori delle istruzioni fornite da Horizon Hobby, LLC. Questo manuale

contiene le istruzioni per un funzionamento e una manutenzione sicuri. È fondamentale leggere e seguire tutte le

istruzioni e le avvertenze del manuale prima di montare, conﬁ gurare ofar funzionare il Prodotto, al ﬁ ne di utilizzarlo

correttamente e di evitare danni olesioni gravi.

MINIMO 14 ANNI. NON È UN GIOCATTOLO.

 COME USARE IL MANUALE

Questo manuale è diviso in sezioni per rendere più facile la comprensione del montaggio.

 AVVERTIMENTI E PRECAUZIONI PER LA SICUREZZA

Prima dell’uso leggere attentamente tutte le istruzioni e le precauzioni per la sicurezza. In caso contrario si potrebbero

procurare incendi, danni o ferite.

Componenti

Usare solo componenti compatibili. Se ci fossero dubbi riguardo alla compatibilità, è opportuno far riferimento alle

istruzioni relative al prodotto o ai componenti oppure rivolgersi al reparto Horizon Hobby di competenza.

Volo

Per sicurezza volare solo in aree molto ampie. Meglio se in campi volo autorizzati per modellismo. Consultare le

ordinanze locali prima di scegliere luogo dove volare.

Elica

Tenere gli oggetti liberi (vestiti, penne, cacciaviti, ecc.) lontano dall’elica, prima che vi restino impigliati. Bisogna fare

attenzione anche con le mani perché c’è il rischio di ferirsi anche gravemente.

Batterie

Quando si maneggiano o si utilizzano le batterie, bisogna attenersi alle istruzioni del costruttore; il rischio è di procurare

incendi, specialmente con le batterie LiPo, con danni e ferite serie.

Piccole parti

Questo kit comprende delle parti di piccole dimensioni e non lo si può lasciare incustodito se c’è la presenza di bambini

che li possono inghiottire e rimanere soffocati o intossicati.

 RACCOMANDAZIONI PER OPERARE IN SICUREZZA

• Controllare attentamente il modello prima di ogni volo per accertarsi che sia idoneo.

• Essere consapevoli che un altro utente della frequenza in uso, potrebbe procurare delle interferenze.

• Essere sempre cortesi e rispettosi nei confronti degli altri utilizzatori dell’area in cui ci si trova.

• Scegliere un’area libera da ostacoli e abbastanza ampia da permettere lo svolgimento del volo in sicurezza.

• Prima del volo veriﬁ care che l’area sia libera da amici e spettatori.

• Stare attenti alle altre attività che si svolgono in vicinanza della vostra traiettoria di volo, per evitare possibili conﬂ itti.

• Pianiﬁ care attentamente il volo prima di lanciare il modello.

• Rispettare sempre scrupolosamente le regole stabilite dall’associazione locale.

 PRIMA DI INIZIARE IL MONTAGGIO

• Togliere tutti i pezzi dalla scatola.

• Veriﬁ care che la fusoliera, l’ala e i piani di coda non siano danneggiati.

• Se si trovano parti danneggiate, contattare il negozio da cui è stato acquistato.

• Caricare il trasmettitore e la batteria di volo.

• Centrare stick e trim sul trasmettitore.

• Con una radio computerizzata creare una nuova memoria per questo modello.

• Facendo riferimento alle istruzioni del radiocomando, connettere (bind) trasmettitore e ricevitore.

IMPORTANTE: Ripetere la procedura di connessione una volta regolate le corse, per evitare che i servi vadano a ﬁ ne

corsa. Garantirà anche che le impostazioni di inversione del servo vengano salvate nel sistema radio.

 PRECAUZIONI PER LA COSTRUZIONE

Durante l’assemblaggio noi consigliamo di appoggiare le varie parti su di una superﬁ cie morbida come un

asciugamano di spugna per evitare ammaccature al rivestimento.

10

 REMOVING WRINKLES

The covering of your model may develop wrinkles during

shipping and will require the use of a heat gun (HAN100)

and covering glove (HAN150) or covering iron (HAN101)

with a sealing iron sock (HAN141) to remove them. Use

caution while working around areas where the colors

overlap to prevent separating the colors. Avoid using

too much heat, which could separate the colors. Placing

a cool damp cloth on adjacent colors will also help in

preventing the separation of the colors while removing

wrinkles.

 TRANSPORTATION AND STORAGE

When transporting and storing your model, you will

need a minimum of 82 inches (2.1m) in length, and 24

inches (61cm) in height to accommodate the size of

the fuselage. The width of the stabilizer must also be

taken into consideration, which is 36 inches (9.2cm).

We also recommend the use of a wing bag (WGT111)

to help protect the wings during transport and storage.

The control horns and linkages can also cause damage

to nearby surfaces even when placed in storage bags.

Always place surfaces so the tops are together to prevent

damage from the control horns and linkages.

 NOSE WEIGHT

Your model may require the addition of nose weight to

properly balance. Our test aircraft with the recommended

Evolution

®

62cc engine and mufﬂ er, and batteries on

either side of the fuel tank required 1

1

/

2

lbs (680g) of

nose weight. This may vary from plane to plane. Add

this weight as far forward in the fuselage as possible to

reduce the amount required to balance. This weight must

be secure so it does not come loose in ﬂ ight, causing

an unsafe model which could result in the loss of the

aircraft.

 REPLACEMENT COVERING

Your model is covered with UltraCote

®

ﬁ lm in the

following colors. If repairs are required, order these

coverings to make those repairs.

White HANU870

Silver HANU881

Deep Red HANU871

 ENTFERNEN VON FALTEN

Während des Transportes können bei der Bespannung

Falten aufgetreten sein. Sie können diese mit dem

Heißluftfön (HAN100) und Bespannhandschuh (HAN150)

oder dem Bügeleisenbezug (HAN141) entfernen. Bitte

achten Sie bei überlappenden Farben diese nicht durch

zuviel Hitze zu lösen. Ein kühlendes Stück Stoff kann hier

neben den Falten aufgelegt helfen, dass die Farben sich

nicht trennen.

 TRANSPORT UND LAGERUNG

Beim Transport und der Lagerung des Modells müssen

mindestens 2,1m (82 Zoll) in der Länge und 61cm

(24 Zoll) in der Höhe vorhanden sein, um die Größe

des Rumpfs aufnehmen zu können. Die Breite des

Stabilisators muss ebenfalls beachtet werden, die

9,2cm (36 Zoll) beträgt. Wir empfehlen außerdem die

Verwendung einer Flügeltasche (WGT111), um die

Tragﬂ ächen bei Transport und Lagerung zu schützen. Die

Steuerhörner und Gestänge können zudem Schäden an

benachbarten Oberﬂ ächen verursachen, auch wenn sie

in Taschen gelagert sind. Oberﬂ ächen stets so platzieren,

dass die Oberseiten aneinander liegen, um Schäden

durch Steuerhörner und Gestänge zu vermeiden.

 BUGGEWICHT

Das Modell kann für das korrekte Gleichgewicht

ein zusätzliches Buggewicht benötigen. Unser

Testﬂ ugzeug mit dem empfohlenen Evolution® 62cm³

Motor und Schalldämpfer sowie auf beiden Seiten

des Kraftstofftanks montierten Akkus benötigte ein

Buggewicht von 680g (11/2 lbs). Dies kann von Flugzeug

zu Flugzeug unterschiedlich sein. Dieses Gewicht so weit

vorne im Rumpf wie möglich hinzufügen, um die für das

Gleichgewicht benötigte Menge zu reduzieren. Dieses

Gewicht muss gesichert werden, damit es sich im Flug

nicht löst, wodurch das Modell unsicher wird und zum

Verlust des Flugzeugs führt.

 ERSATZABDECKUNG

Die nachfolgenden Abdeckungen werden während der

Montage des Modells verwendet. Sind Reparaturen

erforderlich, die nachfolgenden Abdeckungen zur

Durchführung dieser Reparaturen bestellen.

Weiß HANU870

Silber HANU881

Deep Red HANU871

 ÉLIMINATION DES PLIS

L’entoilage de votre modèle peut développer des plis

lors de l’expédition. Vous pouvez les lisser en utilisant le

pistolet à air chaud (HAN100) et le gant (HAN150) ou le

fer à entoiler (HAN101) avec la chaussette de protection

(HAN141). Soyez vigilant sur les zones où plusieurs

couleurs d’entoilage sont superposées, une température

trop élevée pourrait séparer les couleurs. Placez un

chiffon humide et froid sur les couleurs adjacentes pour

éviter leur séparation lorsque vous enlevez les plis.

 TRANSPORT ET STOCKAGE

Lorsque vous transportez et stockez votre modèle, vous

devez avoir au minimum un espace de 2,1m (82po) de

longueur et 61cm (24po) de hauteur pour la taille du

fuselage. La largeur du stabilisateur doit également être

prise en compte: 9,2cm (36po). Nous vous conseillons

également d’utiliser un sac à ailes (WGT111) pour

protéger les ailes lors du transport et du stockage. Les

renvois de commande et tringleries peuvent également

endommager les surfaces proches même si rangés dans

des sacs de rangement. Placez toujours ces surfaces

de manière à ce que les sommets soient ensemble

pour prévenir tout dommage causé par les renvois de

commande et les tringleries.

 POIDS DU NEZ

Votre modèle peut nécessiter l’ajout d’un poids du nez

à des ﬁ ns d’équilibre. Notre appareil test avec le moteur

recommandé Evolution® 62cc et silencieux, avec

batterie de chaque côté du réservoir de carburant a

nécessité un poids du nez de 680g (11/2lb). Cela peut

varier d’un avion à l’autre. Ajoutez ce poids aussi loin que

possible dans le fuselage pour réduire la quantité requise

pour équilibrer. Ce poids doit être ﬁ xé aﬁ n de ne pas se

desserrer en vol, faute de quoi le modèle ne sera pas

sécuritaire pouvant provoquer la perte de l’appareil.

 ENTOILAGE DE RECHANGE

Les entoilages suivants sont utilisés pendant le montage

de votre modèle. Si des réparations sont nécessaires,

commandez les entoilages suivants pour pouvoir

effectuer ces réparations.

Blanc HANU870

Argent HANU881

Rouge foncé HANU871

 TOGLIERE LE GRINZE

rivestimento di questo modello potrebbe sviluppare delle

grinze durante la spedizione e quindi per toglierle, sarà

necessario usare una pistola termica (phon) (HAN100) e

un guanto speciale (HAN150), oppure un ferro apposito

per rivestimenti (HAN101) con la sua calza (HAN141).

Bisogna usare cautela quando si lavora intorno ad

aeree con sovrapposizione di colori per evitare la loro

separazione. Evitare di scaldare troppo per non separare

i colori. Mettere un panno umido fresco sui colori vicini,

aiuta a prevenire la separazione dei colori mentre si

tolgono le grinze.

 TRASPORTO E IMMAGAZZINAGGIO

Durante il trasporto e l’immagazzinaggio del modello,

è necessario uno spazio di almeno 2,1 m (82 pollici) di

lunghezza e 61 cm (24 pollici) di altezza per ospitare la

fusoliera. Inoltre, è necessario prendere in considerazione

la larghezza dello stabilizzatore, pari a 9,2 cm (36 pollici).

È consigliabile usare delle borse alari (WGT111) per

proteggere le ali durante il trasporto e l’immagazzinaggio.

Squadrette e rinvii possono danneggiare le superﬁ ci

circostanti anche all’interno delle borse. Per prevenire

questo problema, sistemare sempre le superﬁ ci facendo

combaciare le superﬁ ci superiori.

 PESO DEL MUSO

Per un bilanciamento accurato, il modello potrebbe

necessitare di un peso aggiuntivo a livello del muso. Il

nostro aeromodello di prova con motore raccomandato

Evolution® 62cc, silenziatore e batterie su ciascun lato

del serbatoio ha richiesto un contrappeso di 680 g (11/2

libbre). Tale peso può variare a seconda dell’aeromodello.

Aggiungere il contrappeso nel punto più avanzato

possibile della fusoliera per ridurre il peso necessario.

Fissare saldamente il contrappeso afﬁ nché non si sposti

durante il volo, rendendo instabile il modello e facilitando

la perdita del controllo.

 COPERTURE DI RICAMBIO

Le seguenti coperture vengono usate durante il

montaggio del vostro modellino. Se sono necessari

interventi di riparazione, ordinare le seguenti coperture.

Bianco HANU870

Argento HANU881

Rosso scuro HANU871

11 EN

Cub Crafters XCub 60cc

 CONTROL HORN INSTALLATION

1. Insert the M3 x 15 socket head cap screw into the hole in the

aileron control horn. Remove any paint using a hobby knife

and #11 blade so the screw ﬁ ts into the hole easily. Check all

the control horns.

2. Use medium-grit sandpaper to lightly sand the aileron control

horn where it ﬁ ts into the aileron. Clean the sanded area

using a paper towel and isopropyl alcohol to remove any

debris or oils. This provides the surface texture necessary for

the epoxy to bond to.

 Use tape on the painted area to help prevent

removing the exposed portion of the control horn.

3. Test ﬁ t the aileron control horn in the slot in the aileron.

4. Place low-tack tape around the aileron control horn. The tape

should be 1/32-inch (1mm) from the control horn as shown.

5. Check that the horn is 90-degrees to the surface of the

aileron. If not, lightly trim the hole in the aileron to reposition

the control horn.

6. Remove the control horn from the control surfaces. Mix 10g

of 15-minute epoxy. Apply epoxy to the slot in the aileron and

ﬂ ap. Make sure the epoxy gets into the slot for a good bond

between the surfaces and control horn.

7. Apply epoxy to the area of the control horn that ﬁ ts into the

slots. Use enough epoxy so the control horns will be fully

bonded to the control surfaces.

8. Before the epoxy fully cures, remove the tape from around

the control horn. This will allow the epoxy to ﬂ ow around the

control horn, creating a small ﬁ llet between the control horn

and surface for a ﬁ nished look and secure bond.

9. Test ﬁ t the remaining control horn. When gluing the control

horn, place the ball end between the horns and insert the

M3 x 15 socket head cap screw through the control horns

and rod ends. This will align the horns correctly, making the

linkage installation easier later.

10. Insert the rudder control horn in the rudder. The tabs on the

horn will rest against the rudder.

12EN

11. Use a felt-tipped pen to mark the control horn on both sides

of the rudder. This will indicate the area of the control horn

where the paint must be removed.

 AILERON SERVO INSTALLATION

16. Remove the aileron servo cover from the wing. Tape the string

to the wing so it won’t fall into the wing.

12. Remove the control horn from the rudder. Place tape against

the lines drawn to prevent removing any unwanted paint. Use

medium-grit sandpaper to lightly sand the control horn where

it ﬁ ts into the udder. Clean the sanded area using a paper

towel and isopropyl alcohol to remove any debris or oils. This

provides the surface texture necessary for the epoxy to bond

to.

17. Use a toothpick or hobby knife to puncture the covering for

the servo cover mounting screws.

13. Prepare the rudder by applying tape to the rudder around the

opening for the rudder control horn. Mix 10g of 15-minute

epoxy and apply it to the sanded area of the rudder control

horn. Insert the rudder control horn in the rudder. Check to

make sure the horn is centered correctly in the rudder. Allow

the epoxy to fully cure before proceeding.

18. Use a #2 Phillips screwdriver to thread the M2.5 x 10 self-

tapping screws into the holes. Remove the screws before

proceeding to the next step.

 Do not press down excessively on the

screw as it could damage the structure.

14. Prepare the remaining rudder control horn. Use the rod ends

and M3 x 15 socket head cap screws to align the second

control horn to the ﬁ rst. Allow the epoxy to fully cure before

removing the screws and rod ends.

19. Apply a small amount of thin CA to harden the threads

made in the previous step. Allow the CA to fully cure before

installing the aileron servo cover.

15. Install the elevator control horns to complete the control horn

installation. Follow the same procedure as the aileron control

horns to install the elevator control horns.

20. Center the aileron servos. Install the aluminum servo arms on

the servos perpendicular to the servo centerline. Prepare both

the right and left aileron servos.

13 EN

Cub Crafters XCub 60cc

21. Fit the servo between the servo mounting tabs in the aileron

servo tray. The servo arm will be centered in the slot. Mark

the locations for the servo mounting screws using a pencil,

then remove the servo.

26. Use the string to pull the servo lead through the wing and out

at the root.

 We left a small amount of the string on the aileron

servo lead so it can be quickly differentiated between

the flap servo lead that will be installed later.

23. Thread a servo mounting screw into each of the holes in the

servo mounting holes. Remove the screws, then apply a small

amount of thin CA to harden the threads made in the previous

step. After the CA has fully cured, secure the servo to the

cover using the screws provided with the servo.

28. Use two rod ends and the 6 inch (152mm) threaded linkage

to construct two aileron pushrods. Thread the rod ends evenly

on the threaded rod. Start with the linkage the length shown

in the photo.

22. Use a drill and a 5/64-inch (2mm) drill bit to drill the holes

for the servo mounting screws in the locations marked in the

previous step.

27. Secure the servo to the wing using four M2.5 x 10 self-

tapping screws. Use a #2 Phillips screwdriver to tighten the

screws.

24. Secure a 24-inch (600mm) servo extension to the servo using

a commercially available retainer (SPMA3054).

25. Tie or tape the string located inside the wing to the end of the

servo lead.

29. Attach one end of the linkage to the control horn using two

M3 washers, an M3 x 15 socket head cap screw and an M3

lock nut. Tighten the hardware using a 2.5mm hex wrench

and 5.5mm nut driver.

 Do not over-tighten the hardware and

damage the control horn or ball end.

30. Attach the opposite end of the linkage to the servo arm using

the hardware provided with the servo arm. Connect the

radio system to the servo and center the servo. Adjust the

linkage as necessary to center the aileron when the servo is

centered.

 Repeat this section for the remaining aileron servo.

14EN

5/8 inch

(16mm)

 FLAP SERVO INSTALLATION

31. Center the servos and install the servo arms on the servos

perpendicular to the servo centerline. Prepare both the right

and left ﬂ ap servos.

32. Remove the ﬂ ap servo cover from the wing. Make sure to

mark the tray so it can be returned to the wing in the correct

direction.

33. Follow the steps outlined for the aileron servos to install the

ﬂ ap servos.

34. The output of the ﬂ ap servo will face toward the leading edge

of the wing.

35. Use two rod ends and the 5

1

/

2

inch (140mm) threaded linkage

to construct two ﬂ ap pushrods. Thread the rod ends evenly on

the threaded rod. Start with the linkage the length shown in

the photo.

36. When attaching the linkage to the servo arm, use the hole in

the arm that is 5/8-inch (16mm) from the center of the arm.

Enlarge this hole using a pin vise and 1/8-inch (3mm) drill bit.

37. Attach the ball end to the servo arm using an M3 x 12 socket

head cap screw, M3 lock nut and M3 washer. Tighten the

hardware using a 2.5mm hex wrench and 5.5mm nut driver.

38. Insert the ﬂ ap servo linkage into the wing. Place the ﬂ ap

servo tray roughly into position, allowing the cover to be

moved so the linkage can be attached to the ﬂ ap.

39. Guide the ﬂ ap servo lead to the root of the wing.

 Use a tie wrap or string to secure the two leads

together. This makes them less likely to fall back

into the wing, and easier to retrieve if they do.

40. Attach the ﬂ ap linkage to the ﬂ ap control horn using two M3

washers, an M3 x 15 socket head cap screw and an M3 lock

nut. Tighten the hardware using a 2.5mm hex wrench and

5.5mm nut driver.

 Do not over-tighten the hardware and

damage the control horn or ball end.

15 EN

Cub Crafters XCub 60cc

41. Check the operation of the ﬂ ap using the radio system. Trim

the sheeting using a hobby knife and #11 blade if any of the

hardware contacts the sheeting.

42. Secure the servo to the wing using four M2.5 x 10 self-

tapping screws. Use a #2 Phillips screwdriver to tighten the

screws.

 Be careful not to press too hard and damage the structure.

43. Connect the ﬂ ap servo to the radio system. Move the switch

on the transmitter to the “UP” ﬂ ap position. Adjust the radio

setting to align the ﬂ ap with the trailing edge of the wing

making sure the aileron is centered. The wing tip can be

used as a guide for aligning the aileron, or step back and look

directly at the trailing edge of the wing to make sure the ﬂ ap

and aileron are aligned.

44. Move the switch at the transmitter to the “MID” ﬂ ap position

of 15/16 inches (24mm). Adjust the radio settings to achieve

the setting for mid ﬂ ap.

45. Move the switch at the transmitter to the “FULL” ﬂ ap position

of 2

3

/

4

inches (70mm). Adjust the radio settings to achieve the

setting for full ﬂ ap.

46. Use hobby scissors or a hobby knife with a new #11 blade to

trim the ﬂ ap linkage cover. Use care not to chip or damage

the paint.

47. Use canopy glue or contact adhesive to attach the ﬂ ap linage

cover to the top of the wing. Use low-tack tape to hold the

cover in position until the adhesive fully cures. Make sure to

operate the ﬂ aps with the fairing in place to make sure fairing

does not interfere with the linkage and cause the fairing to

come loose during operation of the ﬂ aps.

48. Use canopy glue or contact adhesive to attach the wing light

cover to the of the wing. Use low-tack tape to hold the cover

in position until the adhesive fully cures.

 Do not use CA as it will fog the lens.

 WHEEL ASSEMBLY

49. Place one of the aluminum wheel hubs in the center of the

tire.

50. Align the hub so the holes in the center align with the notches

in the tire.

16EN

51. Place the nylon bushing in position in the center of the cover.

52. Fit the remaining aluminum wheel hub into position, aligning

it with the notches in the tire. Also check to make sure the

holes around the bushing are in alignment.

53. Secure the hubs using six 4-40 x 3/4-inch stainless socket

head cap screws and six 4-40 lock nuts. Tighten the

hardware using a 3/32-inch hex wrench and 1/4-inch nut

driver. Tighten the hardware evenly so the wheel will run true

when installed on the axles.

55. Cut a hole in a piece of thin card stock and slide it on the bolt.

Place a drop of threadlock on the bolt near the card stock.

Thread the axle nut on the bolt. Don’t tighten the nut too tight,

preventing the wheel from spinning on the axle bolt.

 Allow the threadlock to fully cure before

proceeding. Once cured, remove the card stock

from the bolt without disturbing the nut.

56. Secure the axle bolt to the landing gear using the axle bolt

lock nut. Use a 6mm hex wrench and 1/2-inch nut driver to

tighten the hardware. Once tightened, make sure the wheel

can spin freely on the axle bolt.

 Use a 1/2-inch open end wrench if necessary to hold

the inner nut in position when tightening the hardware.

57. Check to make sure the landing gear angles toward the front

of the fuselage. The remaining wheel and landing gear strut

can now be installed.

58. Use four M4 x 25 socket head cap screws and four M4

washers to attach the landing gear to the bottom of the

fuselage. Place a drop of threadlock on each screw before

placing it into position. Tighten the screws using a 3mm hex

wrench.

59. Fit the landing gear cover to the fuselage. There is a left and

right cover, so check that the cover conforms to the fuselage

and gear. Use a felt-tipped pen to transfer the screw locations

to the fuselage.

 STANDARD LANDING GEAR INSTALLATION

54. Slide the axle bolt into the bushing from the side of the wheel

with the text.

60. Remove the cover and use a drill and 5/64-inch (2mm) drill

bit to drill the holes for the screws. Thread a screw into each

hole, then remove the screw. Place a few drops of thin CA in

each hole to harden the surrounding wood. Allow the CA to

fully cure before proceeding.

17 EN

Cub Crafters XCub 60cc

61. Once the CA has fully cured, attach the landing gear cover to

the fuselage using two M2.5 x 10 sheet metal screws and a

#2 Phillips screwdriver.

62. The remaining two screws can be installed, completing the

installation of the landing gear covers. Repeat the previous

steps to install the remaining landing gear cover.

 These screws on the bottom of the fuselage are not

essential, but can be used to help the bottom of the fairing sit

closer to the fuselage. Be aware there is only a single layer

of plywood in this area so be careful not to strip the hole.

 SPRUNG LANDING GEAR INSTALLATION

(OPTIONAL)

63. Use a hobby knife and #11 blade to remove the covering for

the strut mount mounting screws.

64. Attach the strut mount to the fuselage using two M3 x 15

socket head cap screws. Place a drop of threadlock on each

screw before placing them into position. Use a 2.5mm hex

wrench to tighten the screws.

 Thread an M3 x 15 socket head cap screw into each

of the blind nuts. If any of the screws are difficult to thread

in, use a 3mm tap and tap handle to clear the threads.

65. Attach the strut mount to the fuselage using two M3 x 15

socket head cap screws. Place a drop of threadlock on each

screw before placing them into position. Use a 2.5mm hex

wrench to tighten the screws.

66. Attach the cross brace to the inner holes on the landing gear

mounts using two M3 x 15 socket head cap screws and

two M3 lock nuts. Tighten the hardware using a 2.5mm hex

wrench and 5.5mm nut driver.

67. Attach the sprung strut to the main landing gear using an M3

x 20 socket head cap screw and M3 lock nut. The spring will

face away from the gear when installed. Tighten the hardware

using a 2.5mm hex wrench and 5.5mm nut driver.

68. Attach the main landing gear to the mounts using two M3 x

15 socket head cap screws and two M3 lock nuts. Tighten the

hardware using a 2.5mm hex wrench and 5.5mm nut driver.

69. Attach the sprung struts to the cross brace using two M3 x 10

socket head cap screws and two M3 lock nuts. Tighten the

hardware using a 2.5mm hex wrench and 5.5mm nut driver.

70. Slide the axle into the wheel hub from the lettered side of the

wheel.

18EN

71. Slide the axle into the main landing gear. Place a drop

of threadlock on the two M3 x 3 setscrews. Thread the

setscrews into the gear, tightening them on the ﬂ at areas of

the axle. Use a 2mm hex wrench to tighten the setscrews.

 Use care not to overtighten the

setscrews and damage the threads.

 Repeat the previous steps to install the remaining wheel.

 WING AND WING STRUT INSTALLATION

72. Slide the wing tube into the wing tube socket.

 The wing tube may be a tight fit in the socket.

Polishing the wing tube with fine sand paper or steel

wool will help ease the installation of the wing tube.

73. Slide the wing into position on the fuselage. Guide the leads

for the ailerons and ﬂ aps into the fuselage. Secure the wing

to the fuselage using two nylon wing bolts.

 The nylon bolt can be shortened to 1

3

/

8

inches

(55mm) to make securing the wing easier.

 Repeat the previous steps to attach

the remaining wing panel.

 In testing, we found that a single wing bolt near the leading

edge of the wing and the installation of the wing struts was

enough to retain the wings even during sustained aerobatics.

75. Attach the strut ﬁ tting near the aileron to the bottom of the

wing using two M3 x 15 socket head cap screws. Apply a

drop of threadlock on each screw before tightening them

using a 2.5mm hex wrench.

 Do not overtighten the screws and

compress the wing sheeting.

76. Attach the strut ﬁ tting near the leading edge to the bottom of

the wing using two M3 x 15 socket head cap screws. Apply

a drop of threadlock on each screw before tightening them

using a 2.5mm hex wrench.

 Do not overtighten the screws and

compress the wing sheeting.

77. Thread the jury strut mounts into the holes in the wing. The

base of the mount will be ﬂ ush with the bottom of the wing.

 Place a drop of canopy glue on the screws before

installation. This will keep the mounts from vibrating loose.

78. Attach the wing struts to the fuselage using two M3 x 15

socket head cap screws and two M3 washers. Tighten the

screws using a 2.5mm hex wrench.

 Place a drop of canopy glue on the screws before

installation. This will keep the screws from vibrating loose

yet leave them easily removable to disassemble the model.

79. Slide the outer strut fairing on the strut.

 The outer strut fairings are optional as

they are a non-functional scale detail.

74. Thread an M3 x 15 socket head cap screw into each of the

blind nuts in the bottom of the wing. If any of the screws do

not thread easily, use a 3mm tap to clear the threads.

19 EN

Cub Crafters XCub 60cc

80. Thread the strut end ﬁ tting on the threaded rod at the end of

the strut. Adjust the position of the end so there is no stress

on the strut when it is attached to the ﬁ tting. Attach the ﬁ tting

to the mount using an M3 x 15 socket head cap screw, two

M3 washers and an M3 locknut. Tighten the hardware using a

2.5mm hex wrench and 5.5mm nut driver.

81. Slide the outer strut fairing against the wing. Mark the

locations for the three mounting screws on the wing.

83. Once the CA has fully cured, slide the fairing back into

position. Use three M2.5 x 10 sheet metal screws and a #2

Phillips screwdriver to secure the fairing to the wing.

 The front and rear struts and fairing

can be installed at this time.

85. The jury strut will ﬁ t over the jury strut ﬁ tting on the bottom of

the wing. Slide the pin through the strut and ﬁ tting.

 A small 1/8-inch (3mm) piece of fuel tubing

can be placed between the jury strut and head of

the pin to prevent the pin from vibrating.

86. Use a keeper to secure the jury strut to the ﬁ tting. Secure

both the front and rear struts.

 The inner strut fairings cannot be installed when the model

has been fitted with the sprung landing gear option. Skip to

the next section if the spring landing gear has been installed.

 The inner strut fairings are optional as

they are a non-functional scale detail.

87. Locate the inner strut fairings. There is a left and right fairing.

Check the ﬁ t of each fairing to make sure they are installed

on the correct sides of the fuselage.

84. Slide the jury struts on the ﬁ tting on the main struts. The

spreader bar is located on the inside of the jury strut on the

side toward the fuselage. Use two M3 x 15 socket head cap

screws, four M3 washers and two M3 lock nuts to secure the

jury struts. Tighten the hardware using a 2.5mm hex wrench

and 5.5mm nut driver.

82. Slide the fairing on the strut. Use a drill and 5/64-inch (2mm)

drill bit to drill the holes for the outer strut fairing screws.

Prepare the holes by threading an M2.5 x 10mm sheet metal

screw in each hole. Remove the screws and apply a few

drops of thin CA in each hole to harden the surrounding wood.

 Use care not to accidentally drill through the top of the wing.

88. Use a #1 Phillips screwdriver or toothpick to remove the

covering exposing the blind nuts used to secure the fairings

to the fuselage. Remove the struts from the fuselage.

 Thread an M3 x 15 socket head cap screw into each

of the blind nuts. If any of the screws are difficult to thread

in, use a 3mm tap and tap handle to clear the threads.

20EN

AA

A=A

AA

A=A

89. Cut two pieces of card stock that are 1/2 x 2 inches (13 x

25mm). Make a 1/8-inch (3mm) hole in each piece. Tape the

card stock to the fuselage with the hole aligned with the blind

nut in the fuselage.

90. Slide the fairing on the strut. Trace around the struts using a

felt-tipped pen.

91. Use a hobby knife and #11 blade, hobby scissors and a rotary

tool with a sanding drum to trim the fairing so the struts can

be reattached to the fuselage.

 Be careful not to chip or damage the

paint on the strut fairing when cutting.

92. Hold the fairing tightly against the fuselage. Use a felt-tipped

pen to mark the locations for the mounting screws on the

fairings.

94. Fit the fairing back on the strut. Attach the struts to the

fuselage, then attach the fairing to the fuselage using two M3

x 15 socket head cap screws and two M3 washers. Tighten

the screws using a 2.5mm hex wrench.

 Place a drop of canopy glue on the screws before

installation. This will keep the screws from vibrating loose

yet leave them easily removable to disassemble the model.

96. Separate the elevators from the stabilizer. Remove all the

hinges.

97. Place the stabilizer on the fuselage. Center the stabilizer on

the fuselage.

 The elevator can be left in position

to aid in centering the stabilizer.

93. Disconnect the struts and remove the fairing. Use a pin vise

and 1/8-inch (3mm) drill bit to drill the mounting holes in the

fairing.

98. Stand back 8-10 feet (2-3 meters) and check that the

stabilizer is aligned with the wing. Lightly sand the stabilizer

saddle on the fuselage to correct any misalignment.

 STABILIZER INSTALLATION

95. Place a small piece of tape on the bottom of the stabilizer and

elevator for identiﬁ cation.

La pagina sta caricando ...

Hangar 9 HAN5260 Manuale del proprietario

Hangar 9 HAN5260 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti