Gold Note Mediterraneo X Manuale utente

USER

MANUAL

MEDITERRANEO X

EN

DE

IT

FR

Thank you for purchasing one of our units

and welcome into the Gold Note world,

where we turn High-End audio and music

into a new experience.

Maurizio Aterini,

founder of Gold Note

EN

DE

IT

FR

|

IMPORTANT SAFETY

| INFORMATION

the third prong are provided for your safety.

If the provided plug does not fit into

your outlet, consult an electrician for

replacement of the obsolete outlet. or

pinched particularly at plugs, convenience

receptacles, and the point where they exit

from the apparatus.

|Only use attachments/accessories specied

by the manufacturer.

|Use only with the cart, stand, tripod,

bracket, or table specied by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

|Unplug this apparatus during lightning

storms or when unused for long periods

of time. Refer all servicing to qualied

service personnel only. Servicing is required

when the apparatus has been damaged in

any way (such as when the power cord or

plug is damaged, liquid has been spilled

or objects have fallen into the apparatus,

the apparatus has been exposed to rain

or moisture) and in any case when the

apparatus does not operate normally or

has been dropped.

PLEASE NOTE

1 Do not disassemble any part of the

product.

2 Do not use any part of the product for

other purposes.

3 For service and problems of any kind,

contact qualified Gold Note personnel.

4 Protect the product from rain, humidity

and keep away from heat sources, electric

and electronic motors etc. The power

cord supplied must be used only on this

unit.

5 Gold Note does not have responsibility

for any improper use of this unit.

GENERIC INFORMATION

|Read these instructions and store them.

|Heed all warnings.

|Follow the instructions.

|Do not use this apparatus near water.

|Clean only with a dry cloth.

|Do not block the ventilation openings

and install in accordance with the

manufacturer’s instructions.

|Do not install near heat sources such as

radiators, heat registers, stoves or other

apparatus (including ampliers) that

produce heat.

|Do not defeat the safety purpose of

the polarised or grounding-type plug: a

polarised plug hastwo blades with one

wider than the other.

|A grounding type plug has two blades and

a third grounding prong. The wide blade or

This appliance has a serial number located on the rear panel.

Please record the model and serial number and retain them for your records.

MODEL

SERIAL NUMBER

CAUTION!

To reduce the risk of electric shock, do not

remove cover (or back). No user-serviceable

parts inside. Refer only to qualified Gold

Note service personnel for service.

WARNING!

To prevent fire or shock hazard, do not

expose this appliance to rain or moisture.

GOLD NOTE - Information on the correct management of waste from

household Equipment pursuant to the European Directive 2012/19/EU

The crossed-out wheelie bin symbol shown on the equipment or its packaging indicates

that the product, at the end of its useful life, must be collected separately from other waste

to allow its proper treatment and recycling. The user must therefore deliver, free of charge,

the end-of-life equipment to the centres for the separate collection of waste electrical and

electronic equipment, or return it to the dealer in accordance with the procedures established

by the legislation.

The appropriate separate collection of discarded equipment allows for proper recycling,

treatment and environmentally compatible disposal, helping to avoid the possible dispersion

of hazardous substances and negative effects on the environment and health, favouring

the reuse and/or recycling of the materials of which the equipment is composed of. Illegal

dumping of the product by the user involves the application of administrative sanction

provided for by the legislation in force. We invite you consult the current legislation and the

measures adopted by the public service operating in your country or territory.

EN

DE

IT

FR

| INDEX

UNBOXING 1

TECHNICAL SPECIFICATIONS 2

SETTING UP THE TURNTABLE 3

INSTALLING THE TURNTABLE 4

POWER ADAPTER 7

SPEED SELECTION & FEATURES 8

CARTRIDGE CALIBRATION 11

DETACHABLE DUST COVER 13

PRODUCT REGISTRATION 14

TROUBLESHOOTING 15

| PACKAGE CONTENT

1x

MEDITERRANEO X

1x

DUST

COVER

(with spacers)

3x

SPIKE

WASHERS

1x

ANTI-

SKATING

1x

OIL JAR

1x

LIFTING EYE

BOLT

1x

USER

MANUAL

1x

GN STYLUS

GAUGE

1x

BALL

BEARING

1x

PROTRACTOR/OVERHANG and

STROBOSCOPE

1x

FELT MAT

1x

DRIVE

BELT

1x

TURNTABLE

CLAMP

1x

PLATTER

SPINDLE TIP

1x

18V POWER

SUPPLY

(with cable)

1x

PHONO

CABLE

1X

TONEARM

(pre-installed and calibrated)

3x

ALLEN KEYS

|2.5mm |1.5mm |2.0mm

2x

COUNTERWEIGHTS

|110g |28.5g

EN

DE

IT

FR

1

| UNBOXING

Oil

Counterweights

Clamp

Platter spindle

Platter spindle tip

Lifting eye bolt

User manual

Belt

Stroboscope,

overhang and

protractor

Platter

Felt mat

Dust cover

Dust cover spacers

Allen keys (3)

Anti-skating

GN stylus gauge

Spike washers

Ball bearing

Power cable

Phono cable

2

MAIN FEATURES

|Wow & utter:

< 0,1%

|Rumble:

-82dB

|Speed:

331/3 rpm and 45 rpm ±0,1%

|Speed changing:

Electronic with fine pitch control

|Transmission:

70 shores rectified EPDM belt

|Motor:

Ultra-precise 12V synchronous motor

|Platter:

Aluminium and high-density POM

(45mm, 7Kg)

|Platter spindle:

Split-spindle™ clamping design

|Platter bearing:

4,3mm ceramic ball

|Tonearm:

Gold Note B-7 Ceramic

|Dust cover:

Smoked acrylic with hinges

POWER

|Power supply:

18V output, 100-240V / 50-60Hz

|Power consumption:

max 27W

| TECHNICAL SPECIFICATIONS

DIMENSIONS AND WEIGHT

Dimensions:

470mm W | 210mm H | 360mm D

590mm W | 510mm H | 460mm D – boxed

Weight:

Kg. 25

Kg. 30 - boxed

EN

DE

IT

FR

3

| SETTING UP THE TURNTABLE

FIRST OPERATION

1 Please remove carefully the protecting

foam and check if all the listed items are

supplied.

2 Place the turntable on a flat surface, then

adjust the feet to level the turntable.

3 Install the counterweight on the tonearm,

ensure the tracking weight matches the

requirements of your cartridge.

4 Install the drive belt around the motor

pulley first, then carefully run it around

the platter.

5 Plug the power adapter cable into the

turntable, then connect it to the AC.

POSITIONING THE TURNTABLE

Your turntable has been designed for Hi-Fi

systems. It must be protected from direct

sun and humidity. Do not place it near

heating sources, electrical and electronic

motors, mobile phones etc. The levelling

and positioning on a solid shelf, is crucial

to achieve the best audio performances

possible.

PITCH ADJUSTMENTS

The pitch can be adjusted easily from the

display.

Select the speed and tap “PITCH”, then

use the + and - icon to precisely adjust the

speed.

Tap “SAVE” to apply the adjustment and exit

the pitch control, tap “BACK” to cancel any

adjustments.

Tap “DEFAULT” to set the speed to the

factory default.

TURNTABLE CONTROLS

The turntable can be fully controlled using

the touchscreen display.

1 Tap the display once to turn ON the

turntable.

2 Tap and hold for 3 seconds the Home

button to turn OFF the turntable.

4

| INSTALLING THE TURNTABLE

Lifting eye

bolt

Platter

spindle

Ball bearing

Platter

Bearing

housing

PLATTER

1 Remove the cap from the center of the

turntable.

2 Insert the ball bearing into the bearing

housing of the turntable taking care to

centre it on the bottom seat.

3 Add oil to the spindle as shown below.

4 Insert the spindle into the bearing

housing.*

5 Screw the lifting eye bolt in the platter to

lift it.

6 Position the platter on the spindle.

1

drop

* PLEASE NOTE: the bearing housing is already

installed in the plinth of the turntable.

Do not remove it.

EN

DE

IT

FR

5

Platter

spindle tip

7 Remove the eye bolt from the platter.

8 Tighten the spindle tip onto the spindle

to lock the platter in place.

9 Wrap the belt around the pulley and the

platter as shown in the picture.

6

1

2

3

1

2

3

2.5 1.5 0.5

ANTI-SKATING AND

COUNTERWEIGHT

Anti-skating: Nylon wire with bullet

counterweight.

Slip the loop of the ANTI-SKATING

nylon wire over the groove of the

ADJUSTMENT BAR.

1

Anti-skating: Adjustment bar.

Feed the wire through the loop of the

SUPPORT HOOP.

Adjust the ANTI-SKATING force

choosing the correct groove on the

ADJUSTMENT BAR.

2

3

Tonearm counterweight: to set up the

correct tracking force depending on the

phono cartridge in use.

3

INSTALLING THE ANTI-SKATING

SYSTEM

EN

DE

IT

FR

7

CONNECTING THE POWER SUPPLY

ADAPTER

Before plugging the power adapter in to the

AC make sure the connector is plugged into

the turntable.

PLEASE NOTE

Use only the original power adapter to

power the turntable to ensure the correct

functioning.

| POWER ADAPTER

VTA SETUP

Use the 1.5mm Allen key supplied to adjust

the VTA. Before moving the tonearm, loosen

the hex bolts found in the tonearm collar.

We recommend to loosen one hex bolt at

a time (usually loosening one is enough to

adjust the VTA).

8

TURNING ON AND OFF THE

TURNTABLE

Connect the Mediterraneo X to the power

supply, then tap the display once (Fig. 1).

HOME PAGE

From the home page you can select the

speed, check the cartridge timer, see

the product information, and adjust the

brightness of the display.

Home

Allows you to select the speed, start/stop the

playback and turn OFF the turntable.

Cartridge menu

Shows the active cartridge and the time

count for all cartridges.

Information

Shows the serial number (S/N) of the unit

and the current rmware version.

Brightness Adjustment

3 options available: 100%, 50% and OFF.

When OFF, tap the display to activate the

brightness temporarily.

| SPEED SELECTION & FEATURES

Fig. 1 Fig. 2

Home

331/3 rpm 45 rpm

Cartridge

menu

Information

Brightness

adjustment

To turn OFF the Mediterraneo X, tap and

hold the Home button for 3 seconds (Fig. 2).

EN

DE

IT

FR

9

33 / 45

Tap the desired speed to start the turntable.

To stop it, tap the speed again.

When the platter’s rotation is stable, the

other functions become available.

Opens the Pitch adjustment.

Opens the Torque adjustment.

Shows the timer viewer to start and stop the

time count for the active cartridge.

PITCH ADJUSTMENT

Pitch adjustment is only available after the

platter speed has stabilised.

Use + and – to increase/decrease the

rotation speed.*

* Please note that the displayed speed is always

33.33, it does not change as you adjust the pitch.

Tap “SAVE” to conrm the pitch adjustment

and store the setting into memory.

Tap “DEFAULT” to set the pitch adjustment

to the factory default.

Tap “BACK” to exit without saving the pitch

adjustment.

10

TORQUE ADJUSTMENT

Adjusting the torque allows you to change

the amount of force applied by the motor to

the pulley and the platter.

Torque is not related to rotational speed -

which can be changed with Pitch adjustment

- and only affects the rotational force.

Changing the torque will result in subtle

audio differences depending on the

combination of cartridge and vinyl. The

torque changes in real-time while the platter

is spinning to give you instant feedback.

You can choose between ve settings.

5 white bars = maximum torque

1 white bar = minimum torque

Please ensure to press SAVE to apply the

selected torque setting.

CARTRIDGE MENU

Tap one of the cartridges to select it as the

active cartridge, this will be displayed in the

timer viewer.

When playing 33/45 LPs, the timer viewer

allows you to start/stop the time count for

the active cartridge.

You can see the time count in minutes for

each cartridge and reset it. When a cartridge

totals over 1000 minutes of playback, it’s

marked in red as it requires maintenance.

TIMER VIEWER

The active cartridge is displayed in the timer

viewer when the speed is selected.

Tap / to start/stop the timer for the

current session, tap to close the viewer.

The time count continues even when the

viewer is closed and until it’s manually

stopped.

When the timer is stopped, the time count

for the session is added to the total time

count for the active cartridge. This can be

viewed in the Cartridge Timer.

EN

DE

IT

FR

11

Our turntables and tone arms are always pre-

calibrated at our factory but you can use the

GN Calibration tool to adjust the:

A Phono Cartridge alignment.

B Overhang.

C 45rpm and 331/3rpm speed (requires a

strobe light).

| CARTRIDGE CALIBRATION

AC B

SPEED ADJUSTMENTS

Check the speed with the help of a strobe

light while the platter is spinning.

The outer line is to check the 331/3 rpm.

The inner line is to check the 45rpm.

OVERHANG

To set the correct overhang the Calibration

Tool must be inserted on to the turntable

record pin and the cartridge Tip must be

positioned on top of the pin.

Adjust the position of the cartridge until the

overhang of the phono cartridge matches

the manufacturer’s specications.

La pagina sta caricando ...

Gold Note Mediterraneo X Manuale utente

Gold Note Mediterraneo X Manuale utente

in altre lingue

Documenti correlati

Altri documenti