Gold Note T-5 Manuale utente

USER

MANUAL

T-5

EN

DE

IT

FR

Thank you for purchasing one of our units

and welcome into the Gold Note world,

where we turn High-End audio and music

into a new experience.

Maurizio Aterini,

founder of Gold Note

EN

DE

IT

FR

|

IMPORTANT SAFETY

| INFORMATION

the third prong are provided for your safety.

If the provided plug does not fit into

your outlet, consult an electrician for

replacement of the obsolete outlet. or

pinched particularly at plugs, convenience

receptacles, and the point where they exit

from the apparatus.

|Only use attachments/accessories specied

by the manufacturer.

|Use only with the cart, stand, tripod,

bracket, or table specied by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

|Unplug this apparatus during lightning

storms or when unused for long periods

of time. Refer all servicing to qualied

service personnel only. Servicing is required

when the apparatus has been damaged in

any way (such as when the power cord or

plug is damaged, liquid has been spilled

or objects have fallen into the apparatus,

the apparatus has been exposed to rain

or moisture) and in any case when the

apparatus does not operate normally or

has been dropped.

PLEASE NOTE

1 Do not disassemble any part of the

product.

2 Do not use any part of the product for

other purposes.

3 For service and problems of any kind,

contact qualified Gold Note personnel.

4 Protect the product from rain, humidity

and keep away from heat sources, electric

and electronic motors etc. The power

cord supplied must be used only on this

unit.

5 Gold Note does not have responsibility

for any improper use of this unit.

GENERIC INFORMATION

|Read these instructions and store them.

|Heed all warnings.

|Follow the instructions.

|Do not use this apparatus near water.

|Clean only with a dry cloth.

|Do not block the ventilation openings

and install in accordance with the

manufacturer’s instructions.

|Do not install near heat sources such as

radiators, heat registers, stoves or other

apparatus (including ampliers) that

produce heat.

|Do not defeat the safety purpose of

the polarised or grounding-type plug: a

polarised plug hastwo blades with one

wider than the other.

|A grounding type plug has two blades and

a third grounding prong. The wide blade or

This appliance has a serial number located on the rear panel.

Please record the model and serial number and retain them for your records.

MODEL

SERIAL NUMBER

CAUTION!

To reduce the risk of electric shock, do not

remove cover (or back). No user-serviceable

parts inside. Refer only to qualified Gold

Note service personnel for service.

WARNING!

To prevent fire or shock hazard, do not

expose this appliance to rain or moisture.

GOLD NOTE - Information on the correct management of waste from

household Equipment pursuant to the European Directive 2012/19/EU

The crossed-out wheelie bin symbol shown on the equipment or its packaging indicates

that the product, at the end of its useful life, must be collected separately from other waste

to allow its proper treatment and recycling. The user must therefore deliver, free of charge,

the end-of-life equipment to the centres for the separate collection of waste electrical and

electronic equipment, or return it to the dealer in accordance with the procedures established

by the legislation.

The appropriate separate collection of discarded equipment allows for proper recycling,

treatment and environmentally compatible disposal, helping to avoid the possible dispersion

of hazardous substances and negative effects on the environment and health, favouring

the reuse and/or recycling of the materials of which the equipment is composed of. Illegal

dumping of the product by the user involves the application of administrative sanction

provided for by the legislation in force. We invite you consult the current legislation and the

measures adopted by the public service operating in your country or territory.

EN

DE

IT

FR

| INDEX

TECHNICAL SPECIFICATIONS 1

SET-UP INSTRUCTIONS 2

UNBOXING 3

INSTALLING THE TURNTABLE 4

OPERATION 8

CARTRIDGE CALIBRATION 9

DETACHABLE DUST COVER 11

PRODUCT REGISTRATION 12

TROUBLESHOOTING 13

| PACKAGE CONTENT

1x

T-5

1x

DUST

COVER

(with spacers)

3x

SPIKE

WASHERS

1x

USER

MANUAL

1x

GN STYLUS

GAUGE

1x

PROTRACTOR/OVERHANG

AND STROBOSCOPE

1x

FELT MAT

1x

DRIVE

BELT

1x

POWER

ADAPTER

1X

TONEARM

(pre-installed and calibrated)

1x

ANTI-SKATING

(bar, screws and counterweight)

1x

COUNTERWEIGHT

|118g

3x

ALLEN KEYS

|2.5mm |1.5mm |2.0mm

EN

DE

IT

FR

1

MAIN FEATURES

|Speed:

331/3 rpm and 45rpm ±0,1%

|Speed changing:

Manual

|Transmission:

70 shores rectified NBR belt

|Motor:

High torque 12V synchronous

|Platter:

Ultra-clear soda lime glass (15mm)

|Plinth:

HDF with vibration-damping geometry

(22mm)

|Platter bearing:

Inverted design with 5mm chromed steel

ball bearing

|Tonearm:

Gold Note B-5.2

|Dust cover:

Transparent acrylic with hinges

| TECHNICAL SPECIFICATIONS

POWER

|Power supply:

12V, 100-120V 60Hz or

12V, 200-240V 50Hz

|Power consumption:

max 3W

DIMENSIONS AND WEIGHT

Dimensions:

425mm W | 140mm H | 360mm D

Weight:

Kg. 7.5

Kg. 12.5 - boxed

2

| SET-UP INSTRUCTIONS

CAUTION

Please pay attention while unpacking the

turntable. The tonearm and the headshell

connectors are extremely delicate and must

be handled carefully to avoid damages to

the tonearm.

FIRST OPERATION

1 Please remove carefully the protecting

foam and check if all the listed items are

supplied.

2 Place the turntable on a levelled surface.

3 Fine tune the counterweight on the

tonearm ensuring the tracking weight

matches the requirements of your

cartridge.

4 Install the drive belt around the motor

pulley first, then carefully run it around

the platter.

5 Connect the turntable to the power

outlet.

POSITIONING THE TURNTABLE

Your turntable has been designed for Hi-Fi

systems. It must be protected from direct sun

and humidity. Do not place it near heating

sources, electrical and electronic motors,

mobile phones etc. The positioning on a

solid shelf, is crucial to achieve the best

audio performances possible.

SPEED SELECTION

To change the speed, place the belt on the

appropriate groove the pulley.

See page 8 for more info.

EN

DE

IT

FR

3

| UNBOXING

Dust cover spacers

Allen keys (3)

Anti-skating

GN stylus gauge

Spike washers

Stroboscope,

overhang and

protractor

Belt

Platter

Counterweight

Felt mat

Power adapter

4

| INSTALLING THE TURNTABLE

Platter

PLATTER SECTION

Small bevel = top side

Big bevel = bottom side

Platter

spindle

PLATTER

1 Position the platter on the spindle

ensuring the correct side is facing

upward.

2 Place the felt mat on the platter.

IMPORTANT

The platter bearing and spindle come

installed. To avoid damages, please do not

remove them.

EN

DE

IT

FR

5

1

2

3

BELT

Wrap the belt around the pulley and the

platter as shown in the picture.

ANTI-SKATING AND

COUNTERWEIGHT

Anti-skating: Nylon wire with bullet

counterweight.

1

Anti-skating: Adjustment bar.

2

Tonearm counterweight: to set up the

correct tracking force depending on the

phono cartridge in use.

3

6

INSTALLING AND CALIBRATING THE

ANTI-SKATING

The anti-skating bar and the screws (2) are

packaged separately.

1 Install the anti-skating bar on the tonearm

ensuring the correct alignment and

tightening the screws gently.

2 Slip the loop of the anti-skating nylon wire

over the groove of the anti-skating bar.

2.5 1.5 0.5

3 Feed the wire through the loop of the

support hoop.

4 Adjust the anti-skating force choosing the

correct groove on the anti-skating bar.

EN

DE

IT

FR

7

Two

on the rear

VTA SETUP

Use the 1.5mm Allen key supplied to adjust

the VTA. Before moving the tonearm, loosen

the hex bolts found in the tonearm collar.

We recommend to loosen one hex bolt at

a time (usually loosening one is enough to

adjust the VTA).

8

| OPERATION

POWER ON/OFF

Use the supplied cable to power the

turntable. Connect the power to the mains

socket rst and then to the turntable.

Use the ON/OFF button to power ON/OFF

the turntable. To set the desired speed,

follow the instructions below.

SPEED SELECTION

To change the speed, place the belt on the

appropriate groove the pulley.

Power cable

50 Hz 60 Hz

ON/OFF

button

33rpm:

Place the belt in the lower groove.

45rpm:

Place the belt in the higher groove.

45 rpm

331/3 rpm

IMPORTANT

Do not use power supplied or power

adapters other than the original to avoid

damages to the motor.

EN

DE

IT

FR

9

| CARTRIDGE CALIBRATION

Our turntables and tone arms are always pre-

calibrated at our factory but you can use the

GN Calibration tool to adjust the:

A Overhang.

B Phono Cartridge alignment.

BA

10

OVERHANG

To set the correct overhang the Calibration

Tool must be inserted on to the turntable

record pin and the cartridge Tip must be

positioned on top of the pin.

Adjust the position of the cartridge until the

overhang of the phono cartridge matches

the manifacturer’s specications.

ALIGNMENT

To correctly align the phono cartridge and

achieve the best tracking position, point the

tip of the phono cartridge into the circles as

in the picture below.

The body of the phono cartridge must be

aligned to the vertical lines.

EN

DE

IT

FR

11

| DETACHABLE DUST COVER

The dust cover features detachable hinges, a

new proprietary design developed to let you

enjoy your turntable at the best.

The hinges provide a stop point at about

90°: in this position the dust cover is stable

and held in place by the hinges.

Removing the dust cover is simple and

quick: lift the dust cover until it reaches the

90° stop point and it’s completely opened,

then gently slide it towards LEFT (facing the

turntable) to detach it from the plinth.

Please note: the dust cover can be removed

and reinserted only when it’s in its resting

position, at 90°.

12

| PRODUCT REGISTRATION

PRODUCT REGISTRATION

We recommend to register the unit on our

internet website within 15 days from the

purchase at

www.goldnote.it/product-registration

If the unit is not registered correctly or has

been purchased from a different country of

the purchaser home address the unit will

not be covered by any warranty and the

registration will be refused.

Please note that the warranty does not cover

in any case: Tubes, Phono Cartridge Stylus

and Batteries.

WARRANTY

All Gold Note products come with a

warranty against defective materials and

workmanship.

Any service and inspection must be carried

out by a Gold Note dealer or distributor so

in case you need any assistance with this

product, please contact the seller.

PLEASE NOTE

Descriptions and technical characteristics

may vary at any time and without notice.

www.goldnote.it/product-

registration

WARNING

Gold Note products should only be

opened, serviced and inspected by certified

Gold Note technicians and dealers. Work

performed by unqualified personnel may

cause serious damage or personal injury.

Opening of the product by non-authorised

personnel will void the guarantee.

In this case, contact your dealer to be

advised on how the fault can be solved.

Do not return any object directly to the

factory or to the distributor without being

authorised to do so.

EN

DE

IT

FR

13

Discover more on our website

www.goldnote.it

| TROUBLESHOOTING

PROBLEM CAUSE SOLUTION

Levelling the turntable.

Cleaning the turntable.

Motor heating.

Noise on startup.

|The turntable is not

levelled.

|Use a spirit level to help

yourself and adjust the

levelling by screwing or

unscrewing the feet.

Unscrewing a foot increase

the height of that corner.

|With EXTREME care use

ONLY very soft 100%

cotton cloth to sweep

dust and stains out.

Any acid, alcohol or not

extremely soft cloth will

irreversibly damage the

turntable ne aesthetic.

Only dry cloth is allowed.

|During operations,

it is normal for AC

synchronous motors to

warm up to 50° Celsius.

|The driving belt drives

the platter by friction

and can produce a small

noise when initiating the

rotation.

|The turntable is dusty or

requires cleaning.

|The motor feels warm.

|There’s a rubbing noise

for a couple of seconds

when the motor starts to

spin.

La pagina sta caricando ...

Gold Note T-5 Manuale utente

Gold Note T-5 Manuale utente

in altre lingue

Documenti correlati

Altri documenti