ASROCK K7NF2-RAID Manuale del proprietario

11

1

ASRock K7NF2-RAID Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any

kind, either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Published March 2005

ASRock K7NF2-RAID Motherboard

22

2

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

EnglishEnglish

English

1 PS2_USB_PWR1 Jumper 16 Infrared Module Connector (IR1)

2 FID Jumpers (FID0, FID1, FID2, FID3, FID4) 17 USB 2.0 Header (USB67, Blue)

3 CPU Socket 18 Floppy Connector (FLOPPY1)

4 North Bridge Controller 19 Game Connector (GAME1)

5 CPU Fan Connector (CPU_FAN1) 20 JR1 / JL1 Jumpers

6 184-pin DDR DIMM Slots (DDR1- 3) 21 Front Panel Audio Connector (AUDIO1)

7 AGP Slot (AGP1) 22 Flash Memory

8 Secondary Serial ATA Connector (SATA2) 23 PCI Slots (PCI1- 5)

9 Primary Serial ATA Connector (SATA1) 24 Clear CMOS Jumper (CLRCMOS2)

10 South Bridge Controller 25 Internal Audio Connector: AUX1 (White)

11 Primary IDE Connector (IDE1, Blue) 26 Internal Audio Connector: CD1 (Black)

12 Secondary IDE Connector (IDE2, Black) 27 ATX Power Connector (ATXPWR1)

13 Chassis Fan Connector (CHA_FAN1) 28 Shared USB 2.0 Header (USB45E, Blue)

14 System Panel Connector (PANEL1) 29 FSB Select Jumper (FSB_SEL1)

15 Chassis Speaker Connector (SPEAKER 1) 30 FSB Select Jumper (FSB_SEL0)

33

3

ASRock K7NF2-RAID Motherboard

ASRock I/O PlusASRock I/O Plus

ASRock I/O Plus

TMTM

TM

1 Parallel Port 7 USB 2.0 Ports (USB01)

2 RJ-45 Port 8 USB 2.0 Ports (USB23)

3 Line In (Light Blue) 9 Serial Port: COM1

4 Line Out (Lime) 10 PS/2 Keyboard Port (Purple)

5 Microphone (Pink) 11 PS/2 Mouse Port (Green)

6 USB 2.0 Ports (USB45)

EnglishEnglish

English

ASRock K7NF2-RAID Motherboard

44

4

EnglishEnglish

English

1. Introduction1. Introduction

1. Introduction

Thank you for purchasing ASRock K7NF2-RAID motherboard, a reliable motherboard

produced under ASRock’s consistently stringent quality control. It delivers excellent

performance with robust design conforming to ASRock’s commitment to quality and

endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might be

updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice.

You may find the latest memory and CPU support lists on ASRock

website as well.

ASRock website

http://www.asrock.com

1.1 Package Contents1.1 Package Contents

1.1 Package Contents

ASRock K7NF2-RAID Motherboard

(ATX Form Factor: 12.0-in x 7.8-in, 30.5 cm x 19.8 cm)

ASRock K7NF2-RAID Quick Installation Guide

ASRock K7NF2-RAID Support CD

One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable

One Ribbon Cable for a 3.5-in Floppy Drive

One Serial ATA (SATA) Cables

One Serial ATA (SATA) HDD Power Cable (Optional)

One ASRock I/O Plus

TM

Shield

One Game Port Bracket (Optional)

55

5

ASRock K7NF2-RAID Motherboard

EnglishEnglish

English

1.2 Specifications1.2 Specifications

1.2 Specifications

Platform: ATX Form Factor (12.0-in x 7.8-in, 30.5-cm x 19.8-cm)

CPU: Supports Socket A (462 pins) for

AMD Athlon

TM

/ Athlon

TM

XP / Sempron

TM

/ Duron

TM

processor

Chipsets: North Bridge:

nVidia nForce 2 Ultra 400, FSB @ 400/333/266/200 MHz,

AGP 8X;

South Bridge:

MCP-RAID, supports USB 2.0, ATA 133, SATA 1.5Gb/s

Memory: 3 DDR DIMM slots: DDR1, DDR2, and DDR3

PC2100 (DDR266) / PC2700 (DDR333) / PC3200 (DDR400)

for 3 DDR DIMM slots, Max. 3GB;

IDE: IDE1: ATA 133 / Ultra DMA Mode 6;

IDE2: ATA 133 / Ultra DMA Mode 6;

Supports up to 4 IDE devices

Serial ATA: 2 SATA connectors,

support up to 2 SATA devices at1.5Gb/s data transfer rate

(Not Support “Hot Plug” function)

Floppy Port: Supports up to 2 floppy disk drives

Audio: 5.1 channels AC’97 Audio

LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN

Hardware Monitor: CPU temperature sensing;

Chassis temperature sensing;

CPU overheat shutdown to protect CPU life

(ASRock U-COP)(see CAUTION 1);

CPU fan tachometer; Chassis fan tachometer;

Voltage monitoring: +12V, +5V, +3.3V, Vcore

PCI slots: 5 slots with PCI Specification 2.3

AGP slot: 1 AGP slot, supports 1.5V, AGP 8X card (see CAUTION 2)

USB 2.0: 8 USB 2.0 ports:

includes 6 default USB 2.0 ports on the rear panel,

plus two headers to support 2 additional USB 2.0 ports

(see CAUTION 3)

ASRock I/O Plus

TM

: 1 PS/2 keyboard port, 1 PS/2 mouse port;

1 serial port: COM1;

1 parallel port: ECP/EPP support;

1 RJ 45 port;

6 default USB 2.0 ports;

Audio Jack: Line Out / Line In / Microphone

ASRock K7NF2-RAID Motherboard

66

6

EnglishEnglish

English

BIOS: AMI legal BIOS;

Supports “Plug and Play”;

ACPI 1.1 compliance wake up events;

SMBIOS 2.3.1 support;

CPU frequency stepless control

(only for advanced users’ reference, see CAUTION 4)

OS: Microsoft

®

Windows

®

98 SE / ME / 2000 / XP compliant

CAUTION!

1. While CPU overheat is detected, the system will automatically shutdown.

Please check if the CPU fan on the motherboard functions properly before

you resume the system. To improve heat dissipation, remember to spray

thermal grease between the CPU and the heatsink when you install the PC

system.

2. Do NOT insert a 3.3V AGP card into the AGP slot of K7NF2-RAID

motherboard!It may cause permanent damage!

3. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

XP SP1/2000 SP4. It may not work properly under Microsoft

®

Windows

®

98/ME.

4. Although K7NF2-RAID offers stepless control, it is not recommended to

perform over clocking. Frequencies other than the recommended CPU bus

frequencies may cause the instability of the system or damage the CPU.

The CPU host frequency of this motherboard is determined by the jumper-

setting. You must set the FSB jumper according to your AMD CPU before

you use the “Manual” option as the FSB setting in BIOS setup to perform

over clocking. Please check page 24 of “User Manual” in the Support CD for

details.

77

7

ASRock K7NF2-RAID Motherboard

2. Installation2. Installation

2. Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install motherboard

components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static electricity,

NEVER place your motherboard directly on the carpet or the like. Also

remember to use a grounded wrist strap or touch a safety grounded

object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded

antstatic pad or in the bag that comes with the component.

2.1 CPU Installation2.1 CPU Installation

2.1 CPU Installation

STEP 1: Unlock the socket by lifting the lever up to a 90

o

angle.

STEP 2: Position the CPU directly above the socket such that its marked

corner matches the base of the socket lever.

STEP 3: Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

STEP 4: When the CPU is in place, press it firmly on the socket while you

push down the socket lever to secure the CPU. The lever clicks on

the side tab to indicate that it is locked.

STEP 5: Install CPU fan and heatsink. For proper installation, please kindly

refer to the instruction manuals of your CPU fan and heatsink vendors.

EnglishEnglish

English

ASRock K7NF2-RAID Motherboard

88

8

EnglishEnglish

English

2.22.2

2.2

Installation of Memory Modules (DIMM)Installation of Memory Modules (DIMM)

Installation of Memory Modules (DIMM)

K7NF2-RAID motherboard provides three 184-pin DDR (Double Data Rate) DIMM slots,

and supports Dual Channel Memory Technology. To enable Dual-Channel mode, you

need to install 2 DIMMs into DDR1 and DDR3 slots. Although this chipset can work on

the Dual-Channel mode with 2 different modules, we recommend users to use two

identical (the same brand, speed, size and chip-type) memory modules in the DDR

DIMM slots for optimized performance.

If you install only one memory module, please install it on DDR1 first.

If you install 2 memory modules, please install them on DDR1 and

DDR3.

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into

the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

99

9

ASRock K7NF2-RAID Motherboard

2.3 Expansion Slots (PCI and AGP Slots)2.3 Expansion Slots (PCI and AGP Slots)

2.3 Expansion Slots (PCI and AGP Slots)

There are 5 PCI slots and 1 AGP slot on K7NF2-RAID motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

AGP slot: The AGP slot is used to install a graphics card.

The ASRock AGP slot has a special locking mechanism which can

securely fasten the graphics card inserted.

Please do NOT use a 3.3V AGP card on the AGP slot of K7NF2-RAID

motherboard! It may cause permanent damage! For the voltage

information of your VGA card, please check with the VGA card vendors.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

STEP 1: Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

STEP 2: Remove the bracket facing the slot that you intend to use. Keep the screws

for later use.

STEP 3: Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

STEP 4: Fasten the card to the chassis with screws.

2.4 Jumpers Setup2.4 Jumpers Setup

2.4 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

Short

Open

EnglishEnglish

English

ASRock K7NF2-RAID Motherboard

1010

10

EnglishEnglish

English

Jumper Setting

FSB_SEL0

(see p.2 item 30)

FSB_SEL1

(see p.2 item 29)

Note: The setting of the CPU front side bus frequency of this motherboard is by means of the

adjustment of jumper-setting. You must set the FSB jumper according to your AMD CPU

before you use the “Manual” option as the FSB setting in BIOS setup to perform over

clocking. Please follow the figures above to set the CPU front side bus frequency.

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2 item 1) +5VSB (standby) for PS/2

or USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by power supply.

JR1(see p.2 item 20)

JL1(see p.2 item 20)

Note: If the jumpers JL1 and JR1 are short, both the front panel and the rear panel audio

connectors will work.

Clear CMOS Jumper

(CLRCMOS2)

(see p.2 item 24)

Note: CLRCMOS2 allows you to clear the data in CMOS. The data in CMOS includes system

setup information such as system password, date, time, and system setup parameters. To

clear and reset the system parameters to default setup, please turn off the computer and

unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper

cap to short 2 pins on CLRCMOS2 for 5 seconds. However, please do not clear the CMOS

right after you update the BIOS. If you need to clear the CMOS when you just finish

updating the BIOS, you must boot up the system first, and then shut it down before you

do the clear-CMOS action.

FID Jumpers

(FID0, FID1, FID2, FID3, FID4)

(see p.2 item 2)

Note: The set of FID jumpers are designed to adjust the multiplier of CPU. For detailed information,

please refer to page 15 of user Manual in the Support CD.

2-pin jumper

1111

11

ASRock K7NF2-RAID Motherboard

2.5 Connectors2.5 Connectors

2.5 Connectors

Connectors are NOT jumpers. DO NOT place jumper caps over

these connectors. Placing jumper caps over the connectors will

cause permanent damage of the motherboard!

FDD Connector

(33-pin FLOPPY1)

(see p.2 item 18)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE Connector (Blue) Secondary IDE Connector (Black)

(39-pin IDE1, see p.2 item 11) (39-pin IDE2, see p.2 item 12)

Note: If you use only one IDE device on this motherboard, please set the IDE

device as “Master”. Please refer to the instruction of your IDE device

vendor for the details. Besides, to optimize compatibility and performance,

please connect your hard disk drive to the primary IDE connector (IDE1,

blue) and CD-ROM to the secondary IDE connector (IDE2, black).

Serial ATA Connectors These two Serial ATA (SATA)

(SATA1: see p.2 item 9) connectors support SATA data

(SATA2: see p.2 item 8) cables for internal storage

devices. The current SATA

interface allows up to 1.5 Gb/s

data transfer rate.

Serial ATA (SATA) Either end of the SATA data cable

Data Cable can be connected to the SATA

hard disk or the SATA

connector on the motherboard.

connect the black end

to the IDE devices

connect the blue end

to the motherboard

80-conductor ATA 66/100/133 cable

the red-striped side to Pin1

SATA1

SATA2

EnglishEnglish

English

ASRock K7NF2-RAID Motherboard

1212

12

EnglishEnglish

English

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on each drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

USB 2.0 Connector ASRock I/O Plus

TM

provides you

(9-pin USB67) 6 default USB 2.0 ports on the

(see p.2 item 17) rear panel. If the rear USB ports

are not sufficient, this USB 2.0

connector (USB67) is available

to support 2 additional USB 2.0

ports.

Shared USB 2.0 Connector This USB45 connector is shared

(9-pin USB45) with the USB 2.0 ports 4,5 on

(see p.2 item 28) the rear panel. When using the

front panel USB ports by

attaching the front panel USB

cable to this header (USB45),

the shared USB ports 4,5 on

the rear panel will not be able

to function.

Infrared Module Connector This connector supports an

(5-pin IR1) optional wireless transmitting

(see p.2 item 16) and receiving infrared module.

Internal Audio Connectors These connectors allow you to

(4-pin CD1, 4-pin AUX1) receive stereo audio input from

(CD1: see p.2 item 26) sound sources such as a

(AUX1: see p.2 item 25) CD-ROM, DVD-ROM, TV tuner

card, or MPEG card.

Front Panel Audio Connector This is an interface for front

(9-pin AUDIO1) panel audio cable that allows

(see p.2 item 21) convenient connection and

control of audio devices.

CD1

AUX1

connect to the

power supply

connect to the SATA

HDD power connector

1313

13

ASRock K7NF2-RAID Motherboard

System Panel Connector This connector accommodates

(9-pin PANEL1) several system front panel

(see p.2 item 14) functions.

Chassis Speaker Connector This connector allows you to

(4-pin SPEAKER 1) attach to the chassis speaker.

(see p.2 item 15)

Chassis Fan Connector Connect the fan cable to the

(3-pin CHA_FAN1) connector matching the black

(see p.2 item 13) wire to the ground pin.

CPU Fan Connector Connect the fan cable to the

(3-pin CPU_FAN1) connector matching the black

(see p.2 item 5) wire to the ground pin.

ATX Power Connector Connect an ATX power supply

(20-pin ATXPWR1) to the connector.

(see p.2 item 27)

Game Connector Connect a Game cable to this

(15-pin GAME1)

connector if the Game port

(see p.2 item 19) bracket is installed.

Game cable with the

Game port bracket

(Optional)

connect to the Game connector

EnglishEnglish

English

ASRock K7NF2-RAID Motherboard

1414

14

EnglishEnglish

English

2.62.6

2.6

Serial ASerial A

Serial A

TT

T

A (SAA (SA

A (SA

TT

T

A) Hard Disks InstallationA) Hard Disks Installation

A) Hard Disks Installation

This motherboard supports Serial ATA (SATA) hard disks and RAID functions. This

section will guide you to install the SATA hard disks.

STEP 1: Install the SATA hard disks into the drive bays of your chassis.

STEP 2: Connect the SATA power cable to the SATA hard disk.

STEP 3: Connect one end of the SATA data cable to the motherboard’s SATA

connector.

STEP 4: Connect the other end of the SATA data cable to the SATA hard disk.

2.72.7

2.7

Installing Windows 2000 / Windows XP With RAIDInstalling Windows 2000 / Windows XP With RAID

Installing Windows 2000 / Windows XP With RAID

FunctionsFunctions

Functions

If you want to install Windows 2000 or Windows XP on your SATA HDDs with RAID

functions, please follow the below steps.

STEP 1: Make a SATA Driver Diskette.

A. Insert the ASRock Support CD into your optical drive to boot your system.

B. During POST at the beginning of system boot-up, press <F11> key, and

then a window for boot devices selection appears. Please select CD-

ROM as the boot device.

C. When you see the message on the screen, “Do you want to generate

Serial ATA driver diskette [YN]?”, press <Y>.

D. Then you will see these messages,

Please insert a diskette into the floppy drive.

WARNING! Formatting the floppy diskette will

lose ALL data in it!

Start to format and copy files [YN]?

Please insert a floppy diskette into the floppy drive, and press <Y>.

E. The system will start to format the floppy diskette and copy SATA drivers

into the floppy diskette.

STEP 2: Set Up BIOS.

A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration.

B. Set the “SATA Operation Mode” option from [non-RAID] to [RAID].

STEP 3: Use “RAID BIOS Setting Utility” to set RAID configuration.

Before you start to configure the RAID function, you need to

check the installation guide in the Support CD for proper configuration.

Please refer to the document in the Support CD, “Guide to SATA Hard

Disks Installation and RAID Configuration”, which is located in the folder

at the following path:

.. \ RAID BIOS Setting Utility

1515

15

ASRock K7NF2-RAID Motherboard

EnglishEnglish

English

After step1, 2, 3, you can start to install Windows 2000 / Windows XP.

NOTE. If you install Windows 2000 / Windows XP on IDE HDDs and want to manage

(create, convert, delete, or rebuild) RAID functions, you still need to set up

“SATA Operation Mode” to [RAID] first. Then, please set the RAID configura

-tion by using “RAID Utility for Windows” in Windows environment.

Please refer to the document in the Support CD, “Guide to nVidia RAID Utility

for Windows”, which is located in the folder at the following path:

.. \ RAID Utility for Windows

2.92.9

2.9

Installing WInstalling W

Installing W

indows 98 SE / Windows 98 SE / W

indows 98 SE / W

indows ME on SAindows ME on SA

indows ME on SA

TT

T

A HDDA HDD

A HDD

If you want to install Windows 98 SE / Windows ME on SATA HDD, it must be installed

on SATA 1 in order to finish the OS installation process. After finishing the installation

of Windows 98 SE / Windows ME, please install Windows SE 98 / Windows ME

registry patch file provided in the support CD, which is located in the folder at the

following patch:

.. \ Nvidia SATA patch for Win98/ME

Then the SATA HDD can be used in SATA 1 or SATA 2 port.

Windows 98 SE / Windows ME does not support RAID function.

2.82.8

2.8

Installing Windows 2000 / Windows XP Without RAIDInstalling Windows 2000 / Windows XP Without RAID

Installing Windows 2000 / Windows XP Without RAID

FunctionsFunctions

Functions

If you just want to install Windows 2000 or Windows XP on your SATA HDDs without

RAID functions, you don’t have to make a SATA driver diskette. Besides, there is no

need for you to change the BIOS setting. You can start to install Windows 2000 or

windows XP on your system directly.

ASRock K7NF2-RAID Motherboard

1616

16

3. BIOS Information3. BIOS Information

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up the

computer, please press <F2> during the Power-On-Self-Test (POST) to enter BIOS Setup utility;

otherwise, POST continues with its test routines. If you wish to enter BIOS Setup after POST,

please restart the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on

the system chassis.

The BIOS Setup program is designed to be user-friendly. It is a menu-driven program, which allows

you to scroll through its various sub-menus and to select among the predetermined choices. For

the detailed information about BIOS Setup, please refer to the User Manual (PDF file) contained

in the Support CD.

4. Software Suppor4. Software Suppor

4. Software Suppor

t CD informationt CD information

t CD information

This motherboard supports various Microsoft

®

Windows

®

operating systems: 98 SE / ME / 2000

/ XP. The Support CD that came with the motherboard contains necessary drivers and useful

utilities that will enhance motherboard features.

To begin using the Support CD, insert the CD into your CD-ROM drive. It will display the Main

Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear

automatically, locate and double-click on the file “ASSETUP.EXE” from the BIN folder in the

Support CD to display the menus.

EnglishEnglish

English

1717

17

ASRock K7NF2-RAID Motherboard

1818

18

1919

19

ASRock K7NF2-RAID Motherboard

®

” ”

ASRock K7NF2-RAID Motherboard

2020

20

La pagina sta caricando ...

ASROCK K7NF2-RAID Manuale del proprietario

ASROCK K7NF2-RAID Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti